ar71xx: add support for YunCore SR3200 and XD3200

YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

12 files changed, 256 insertions, 4 deletions

diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index a93ea1d..38e665f 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -444,6 +444,9 @@ som9331)
 	ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt"
 	ucidef_set_led_usbdev "usb" "USB" "$board:green:system" "1-1"
 	;;
+sr3200)
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
+	;;
 tellstick-znet-lite)
 	ucidef_set_led_netdev "lan_act" "LANACT" "tellstick:green:lan" "eth0" "tx rx"
 	ucidef_set_led_netdev "lan_link" "LANLINK" "tellstick:orange:lan" "eth0" "link"
@@ -738,6 +741,9 @@ wzr-hp-g300nh)
 	ucidef_set_led_netdev "router" "Router" "buffalo:green:router" "eth1"
 	ucidef_set_led_usbdev "usb" "USB" "buffalo:blue:usb" "1-1"
 	;;
+xd3200)
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:blue:wlan2g" "phy1tpt"
+	;;
 z1)
 	ucidef_set_led_netdev "wlan1" "WLAN1" "$board:blue:tricolor0" "wlan1"
 	;;
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index 949f161..57d690d 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -230,6 +230,7 @@ ar71xx_setup_interfaces()
 	dir-835-a1|\
 	esr900|\
 	mynet-n750|\
+	sr3200|\
 	wndr3700v4|\
 	wndr4300)
 		ucidef_add_switch "switch0" \
@@ -395,7 +396,8 @@ ar71xx_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth0" "1:lan" "2:wan"
 		;;
-	unifiac-pro)
+	unifiac-pro|\
+	xd3200)
 		ucidef_add_switch "switch0" \
 			"0@eth0" "2:lan" "3:wan"
 		;;
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 9b9aea8..43ea2b6 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -18,7 +18,9 @@ get_status_led() {
 	antminer-s3|\
 	antminer-r1|\
 	minibox-v1|\
-	som9331)
+	som9331|\
+	sr3200|\
+	xd3200)
 		status_led="$board:green:system"
 		;;
 	ap132|\
diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 7983dad..97875bd 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -49,7 +49,9 @@ case "$FIRMWARE" in
 	case $board in
 	cf-e380ac-v1|\
 	cf-e380ac-v2|\
-	dlan-pro-1200-ac)
+	dlan-pro-1200-ac|\
+	sr3200|\
+	xd3200)
 		ath10kcal_extract "art" 20480 2116
 		;;
 	dap-2695-a1)
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 526d033..c27cd13 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -905,6 +905,9 @@ ar71xx_board_detect() {
 	*SOM9331)
 		name="som9331"
 		;;
+	*SR3200)
+		name="sr3200"
+		;;
 	*TEW-632BRP)
 		name="tew-632brp"
 		;;
@@ -1190,6 +1193,9 @@ ar71xx_board_detect() {
 	*WHR-HP-G300N)
 		name="whr-hp-g300n"
 		;;
+	*XD3200)
+		name="xd3200"
+		;;
 	*Z1)
 		name="z1"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 5f4375d..7b59bf3 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -228,6 +228,7 @@ platform_check_image() {
 	rocket-m-xw|\
 	rocket-m|\
 	rw2458n|\
+	sr3200|\
 	tew-632brp|\
 	tew-712br|\
 	tew-732br|\
@@ -251,7 +252,8 @@ platform_check_image() {
 	wzr-hp-ag300h|\
 	wzr-hp-g300nh2|\
 	wzr-hp-g300nh|\
-	wzr-hp-g450h)
+	wzr-hp-g450h|\
+	xd3200)
 		[ "$magic" != "2705" ] && {
 			echo "Invalid image type."
 			return 1
diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
index c6a757a..3181797 100644
--- a/target/linux/ar71xx/config-4.4
+++ b/target/linux/ar71xx/config-4.4
@@ -150,6 +150,7 @@ CONFIG_ATH79_MACH_R6100=y
 CONFIG_ATH79_MACH_RW2458N=y
 CONFIG_ATH79_MACH_SMART_300=y
 CONFIG_ATH79_MACH_SOM9331=y
+CONFIG_ATH79_MACH_SR3200=y
 CONFIG_ATH79_MACH_TELLSTICK_ZNET_LITE=y
 CONFIG_ATH79_MACH_TEW_632BRP=y
 CONFIG_ATH79_MACH_TEW_673GRU=y
@@ -217,6 +218,7 @@ CONFIG_ATH79_MACH_WZR_HP_AG300H=y
 CONFIG_ATH79_MACH_WZR_HP_G300NH=y
 CONFIG_ATH79_MACH_WZR_HP_G300NH2=y
 CONFIG_ATH79_MACH_WZR_HP_G450H=y
+CONFIG_ATH79_MACH_XD3200=y
 CONFIG_ATH79_MACH_Z1=y
 CONFIG_ATH79_MACH_ZBT_WE1526=y
 CONFIG_ATH79_MACH_ZCN_1523H=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index f1bfcb8..9e1b50e 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -280,6 +280,17 @@ config ATH79_MACH_SOM9331
 	select ATH79_DEV_USB
 	select ATH79_DEV_WMAC
 
+config ATH79_MACH_SR3200
+	bool "YunCore SR3200 support"
+	select SOC_QCA956X
+	select ATH79_DEV_AP9X_PCI if PCI
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+
 config ATH79_MACH_BHR_4GRV2
 	bool "Buffalo BHR-4GRV2 board support"
 	select SOC_QCA955X
@@ -425,6 +436,16 @@ config ATH79_MACH_WPJ558
 	select ATH79_DEV_USB
 	select ATH79_DEV_WMAC
 
+config ATH79_MACH_XD3200
+	bool "YunCore XD3200 support"
+	select SOC_QCA956X
+	select ATH79_DEV_AP9X_PCI if PCI
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_WMAC
+
 config ATH79_MACH_DGL_5500_A1
 	bool "D-Link DGL-5500 A1 support"
 	select SOC_QCA955X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index ac2dbbb..e573b4b 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -156,6 +156,7 @@ obj-$(CONFIG_ATH79_MACH_RBSXTLITE)		+= mach-rbsxtlite.o
 obj-$(CONFIG_ATH79_MACH_RW2458N)		+= mach-rw2458n.o
 obj-$(CONFIG_ATH79_MACH_SMART_300)		+= mach-smart-300.o
 obj-$(CONFIG_ATH79_MACH_SOM9331)		+= mach-som9331.o
+obj-$(CONFIG_ATH79_MACH_SR3200)			+= mach-sr3200.o
 obj-$(CONFIG_ATH79_MACH_TELLSTICK_ZNET_LITE)	+= mach-tellstick-znet-lite.o
 obj-$(CONFIG_ATH79_MACH_TEW_632BRP)		+= mach-tew-632brp.o
 obj-$(CONFIG_ATH79_MACH_TEW_673GRU)		+= mach-tew-673gru.o
@@ -223,6 +224,7 @@ obj-$(CONFIG_ATH79_MACH_WZR_HP_AG300H)		+= mach-wzr-hp-ag300h.o
 obj-$(CONFIG_ATH79_MACH_WZR_HP_G300NH)		+= mach-wzr-hp-g300nh.o
 obj-$(CONFIG_ATH79_MACH_WZR_HP_G300NH2)		+= mach-wzr-hp-g300nh2.o
 obj-$(CONFIG_ATH79_MACH_WZR_HP_G450H)		+= mach-wzr-hp-g450h.o
+obj-$(CONFIG_ATH79_MACH_XD3200)			+= mach-sr3200.o
 obj-$(CONFIG_ATH79_MACH_Z1)			+= mach-z1.o
 obj-$(CONFIG_ATH79_MACH_ZBT_WE1526)		+= mach-zbt-we1526.o
 obj-$(CONFIG_ATH79_MACH_ZCN_1523H)		+= mach-zcn-1523h.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-sr3200.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-sr3200.c
new file mode 100644
index 0000000..51fcccf
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-sr3200.c
@@ -0,0 +1,187 @@
+/*
+ * Support for YunCore SR3200 and XD3200 boards
+ *
+ * Copyright (C) 2016 Piotr Dymacz <pepe2k@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/phy.h>
+#include <linux/gpio.h>
+#include <linux/ar8216_platform.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define SR3200_XD3200_GPIO_LED_SYSTEM	1
+#define SR3200_XD3200_GPIO_LED_WLAN2G	19
+
+#define SR3200_XD3200_GPIO_BTN_RESET	2
+
+#define SR3200_XD3200_KEYS_POLL_INTERVAL	20
+#define SR3200_XD3200_KEYS_DEBOUNCE_INTERVAL	\
+		(3 * SR3200_XD3200_KEYS_POLL_INTERVAL)
+
+static struct gpio_led xd3200_leds_gpio[] __initdata = {
+	{
+		.name		= "xd3200:green:system",
+		.gpio		= SR3200_XD3200_GPIO_LED_SYSTEM,
+		.active_low	= 1,
+	},
+	{
+		.name		= "xd3200:blue:wlan2g",
+		.gpio		= SR3200_XD3200_GPIO_LED_WLAN2G,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_led sr3200_leds_gpio[] __initdata = {
+	{
+		.name		= "sr3200:green:system",
+		.gpio		= SR3200_XD3200_GPIO_LED_SYSTEM,
+		.active_low	= 1,
+	},
+	{
+		.name		= "sr3200:green:wlan2g",
+		.gpio		= SR3200_XD3200_GPIO_LED_WLAN2G,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button sr3200_xd3200_gpio_keys[] __initdata = {
+	{
+		.desc		= "reset",
+		.type		= EV_KEY,
+		.code		= KEY_RESTART,
+		.debounce_interval = SR3200_XD3200_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= SR3200_XD3200_GPIO_BTN_RESET,
+		.active_low	= 1,
+	},
+};
+
+static const struct ar8327_led_info sr3200_leds_qca833x[] = {
+	AR8327_LED_INFO(PHY0_0, HW, "sr3200:green:lan1"),
+	AR8327_LED_INFO(PHY1_0, HW, "sr3200:green:lan2"),
+	AR8327_LED_INFO(PHY2_0, HW, "sr3200:green:lan3"),
+	AR8327_LED_INFO(PHY3_0, HW, "sr3200:green:lan4"),
+	AR8327_LED_INFO(PHY4_0, HW, "sr3200:green:wan"),
+};
+
+static const struct ar8327_led_info xd3200_leds_qca833x[] = {
+	AR8327_LED_INFO(PHY1_0, HW, "xd3200:green:lan"),
+	AR8327_LED_INFO(PHY2_0, HW, "xd3200:green:wan"),
+};
+
+/* Blink rate: 1 Gbps -> 8 hz, 100 Mbs -> 4 Hz, 10 Mbps -> 2 Hz */
+static struct ar8327_led_cfg sr3200_xd3200_qca833x_led_cfg = {
+	.led_ctrl0 = 0xcf37cf37,
+	.led_ctrl1 = 0xcf37cf37,
+	.led_ctrl2 = 0xcf37cf37,
+	.led_ctrl3 = 0x0,
+	.open_drain = true,
+};
+
+static struct ar8327_pad_cfg sr3200_xd3200_qca833x_pad0_cfg = {
+	.mode = AR8327_PAD_MAC_SGMII,
+	.sgmii_delay_en = true,
+};
+
+static struct ar8327_platform_data sr3200_xd3200_qca833x_data = {
+	.pad0_cfg = &sr3200_xd3200_qca833x_pad0_cfg,
+	.port0_cfg = {
+		.force_link = 1,
+		.speed = AR8327_PORT_SPEED_1000,
+		.duplex = 1,
+		.txpause = 1,
+		.rxpause = 1,
+	},
+	.led_cfg = &sr3200_xd3200_qca833x_led_cfg,
+};
+
+static struct mdio_board_info sr3200_xd3200_mdio0_info[] = {
+	{
+		.bus_id = "ag71xx-mdio.0",
+		.phy_addr = 0,
+		.platform_data = &sr3200_xd3200_qca833x_data,
+	},
+};
+
+static void __init sr3200_xd3200_common_setup(void)
+{
+	u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
+
+	ath79_register_m25p80(NULL);
+
+	ath79_register_mdio(0, 0x0);
+	mdiobus_register_board_info(sr3200_xd3200_mdio0_info,
+				    ARRAY_SIZE(sr3200_xd3200_mdio0_info));
+
+	/* GMAC0 is connected to QCA8334/QCA8337N switch */
+	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+	ath79_eth0_data.phy_mask = BIT(0);
+	ath79_eth0_data.speed = SPEED_1000;
+	ath79_eth0_data.duplex = DUPLEX_FULL;
+
+	ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+	ath79_register_eth(0);
+
+	ath79_register_wmac(mac + 0x1000, NULL);
+
+	ap91_pci_init(mac + 0x5000, NULL);
+
+	ath79_gpio_direction_select(SR3200_XD3200_GPIO_LED_SYSTEM, true);
+	ath79_gpio_direction_select(SR3200_XD3200_GPIO_LED_WLAN2G, true);
+
+	/* Mute LEDs on boot */
+	gpio_set_value(SR3200_XD3200_GPIO_LED_SYSTEM, 1);
+	gpio_set_value(SR3200_XD3200_GPIO_LED_WLAN2G, 1);
+
+	ath79_gpio_output_select(SR3200_XD3200_GPIO_LED_SYSTEM, 0);
+	ath79_gpio_output_select(SR3200_XD3200_GPIO_LED_WLAN2G, 0);
+
+	ath79_register_gpio_keys_polled(-1, SR3200_XD3200_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(sr3200_xd3200_gpio_keys),
+					sr3200_xd3200_gpio_keys);
+}
+
+static void __init sr3200_setup(void)
+{
+	sr3200_xd3200_qca833x_data.leds = sr3200_leds_qca833x;
+	sr3200_xd3200_qca833x_data.num_leds = ARRAY_SIZE(sr3200_leds_qca833x);
+
+	sr3200_xd3200_common_setup();
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(sr3200_leds_gpio),
+				 sr3200_leds_gpio);
+
+	ath79_register_usb();
+}
+
+MIPS_MACHINE(ATH79_MACH_SR3200, "SR3200", "YunCore SR3200", sr3200_setup);
+
+static void __init xd3200_setup(void)
+{
+	sr3200_xd3200_qca833x_data.leds = xd3200_leds_qca833x;
+	sr3200_xd3200_qca833x_data.num_leds = ARRAY_SIZE(xd3200_leds_qca833x);
+
+	sr3200_xd3200_common_setup();
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(xd3200_leds_gpio),
+				 xd3200_leds_gpio);
+}
+
+MIPS_MACHINE(ATH79_MACH_XD3200, "XD3200", "YunCore XD3200", xd3200_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 9a8da22..0054067 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -173,6 +173,7 @@ enum ath79_mach_type {
 	ATH79_MACH_RW2458N,			/* Redwave RW2458N */
 	ATH79_MACH_SMART_300,			/* NC-LINK SMART-300 */
 	ATH79_MACH_SOM9331,			/* OpenEmbed SOM9331 */
+	ATH79_MACH_SR3200,			/* YunCore SR3200 */
 	ATH79_MACH_TELLSTICK_ZNET_LITE,		/* TellStick ZNet Lite */
 	ATH79_MACH_TEW_632BRP,			/* TRENDnet TEW-632BRP */
 	ATH79_MACH_TEW_673GRU,			/* TRENDnet TEW-673GRU */
@@ -282,6 +283,7 @@ enum ath79_mach_type {
 	ATH79_MACH_WZR_HP_G300NH,		/* Buffalo WZR-HP-G300NH */
 	ATH79_MACH_WZR_HP_G300NH2,		/* Buffalo WZR-HP-G300NH2 */
 	ATH79_MACH_WZR_HP_G450H,		/* Buffalo WZR-HP-G450H */
+	ATH79_MACH_XD3200,			/* YunCore XD3200 */
 	ATH79_MACH_Z1,				/* Cisco Meraki Z1 */
 	ATH79_MACH_ZBT_WE1526,			/* Zbtlink ZBT-WE1526 */
 	ATH79_MACH_ZCN_1523H_2,			/* Zcomax ZCN-1523H-2-xx */
diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk
index 6ceabeb..e2867e6 100644
--- a/target/linux/ar71xx/image/generic.mk
+++ b/target/linux/ar71xx/image/generic.mk
@@ -484,6 +484,24 @@ define Device/som9331
 endef
 TARGET_DEVICES += som9331
 
+define Device/sr3200
+  DEVICE_TITLE := YunCore SR3200
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k ath10k-firmware-qca988x
+  BOARDNAME = SR3200
+  IMAGE_SIZE = 16000k
+  CONSOLE = ttyS0,115200
+  MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro
+endef
+TARGET_DEVICES += sr3200
+
+define Device/xd3200
+  $(Device/sr3200)
+  DEVICE_TITLE := YunCore XD3200
+  DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
+  BOARDNAME = XD3200
+endef
+TARGET_DEVICES += xd3200
+
 define Device/tellstick-znet-lite
   $(Device/tplink-16mlzma)
   DEVICE_TITLE := TellStick ZNet Lite