diff options
author | John Crispin <john@openwrt.org> | 2014-11-03 08:00:13 +0000 |
---|---|---|
committer | John Crispin <john@openwrt.org> | 2014-11-03 08:00:13 +0000 |
commit | cc5194cf030c422ef82442091598582cf4aeca34 (patch) | |
tree | 655972cf7bc4b19a6390e84553713349a289cc56 | |
parent | 101289156b4748583995d4cdb27751cea4efe917 (diff) | |
download | mtk-20170518-cc5194cf030c422ef82442091598582cf4aeca34.zip mtk-20170518-cc5194cf030c422ef82442091598582cf4aeca34.tar.gz mtk-20170518-cc5194cf030c422ef82442091598582cf4aeca34.tar.bz2 |
ramips: add support for Airlink101 AR670W
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
-rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/01_leds | 5 | ||||
-rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/02_network | 1 | ||||
-rwxr-xr-x | target/linux/ramips/base-files/etc/diag.sh | 3 | ||||
-rwxr-xr-x | target/linux/ramips/base-files/lib/ramips.sh | 3 | ||||
-rwxr-xr-x | target/linux/ramips/base-files/lib/upgrade/platform.sh | 7 | ||||
-rw-r--r-- | target/linux/ramips/dts/AR670W.dts | 103 | ||||
-rw-r--r-- | target/linux/ramips/image/Makefile | 27 | ||||
-rw-r--r-- | target/linux/ramips/rt288x/config-3.14 | 1 |
8 files changed, 147 insertions, 3 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 4a482b3..bd8c779 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -41,12 +41,11 @@ case $board in ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "all0256n:green:rssihigh" "wlan0" "70" "100" "-69" "8" set_wifi_led "rt2800pci-phy0::radio" ;; + ar670w|\ + ar725w|\ awapn2403) set_wifi_led "rt2800soc-phy0::radio" ;; - ar725w) - set_wifi_led "rt2800soc-phy0::radio" - ;; asl26555) ucidef_set_led_default "power" "POWER" "asl26555:green:power" "1" ucidef_set_led_netdev "eth" "ETH" "asl26555:green:eth" "eth0" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 1c7d80c..cedcb8b 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -157,6 +157,7 @@ ramips_setup_interfaces() ucidef_add_switch_vlan "switch0" "2" "0 5t" ;; + ar670w | \ ar725w | \ rt-n15 | \ wl-351) diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index 2977099..709158b 100755 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -12,6 +12,9 @@ get_status_led() { 3g300m | w150m) status_led="tenda:blue:ap" ;; + ar670w) + status_led="ar670w:green:power" + ;; ar725w) status_led="ar725w:green:power" ;; diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index e3977aa..a02bcf9 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -28,6 +28,9 @@ ramips_board_detect() { *"A5-V11") name="a5-v11" ;; + *"Airlink101 AR670W") + name="ar670w" + ;; *"Airlink101 AR725W") name="ar725w" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 4fe0ef4..decbc54 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -110,6 +110,13 @@ platform_check_image() { } return 0 ;; + ar670w) + [ "$magic" != "6d000080" ] && { + echo "Invalid image type." + return 1 + } + return 0 + ;; cy-swr1100 |\ dir-610-a1 |\ dir-645) diff --git a/target/linux/ramips/dts/AR670W.dts b/target/linux/ramips/dts/AR670W.dts new file mode 100644 index 0000000..07497cb --- /dev/null +++ b/target/linux/ramips/dts/AR670W.dts @@ -0,0 +1,103 @@ +/dts-v1/; + +/include/ "rt2880.dtsi" + +/ { + compatible = "AR670W", "ralink,rt2880-soc"; + model = "Airlink101 AR670W"; + + palmbus@300000 { + gpio0: gpio@600 { + status = "okay"; + }; + }; + + pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "i2c", "spi", "uartlite"; + ralink,function = "gpio"; + }; + }; + }; + + ethernet@400000 { + status = "okay"; + mtd-mac-address = <&factory 0x2004>; + + port@0 { + phy-handle = <&phy0>; + phy-mode = "mii"; + }; + + mdio-bus { + status = "okay"; + phy0: ethernet-phy@0 { + phy-mode = "mii"; + reg = <0>; + }; + }; + }; + + wmac@480000 { + status = "okay"; + ralink,mtd-eeprom = <&factory 0x2000>; + }; + + cfi@bdc00000 { + compatible = "cfi-flash"; + reg = <0xbc400000 0x800000>; + + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + + u-boot@0 { + reg = <0x0 0x30000>; + label = "u-boot"; + read-only; + }; + + factory: factory@30000 { + reg = <0x30000 0x10000>; + label = "factory"; + read-only; + }; + + firmware@40000 { + reg = <0x40000 0x3c0000>; + label = "firmware"; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + status { + label = "ar670w:green:power"; + gpios = <&gpio0 7 1>; + }; + + wpsblue { + label = "ar670w:blue:wps"; + gpios = <&gpio0 13 1>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + wps { + label = "wps"; + gpios = <&gpio0 0 1>; + linux,code = <0x211>; + }; + reset { + label = "reset"; + gpios = <&gpio0 9 1>; + linux,code = <0x198>; + }; + }; +}; diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile index 759de53..1f03386 100644 --- a/target/linux/ramips/image/Makefile +++ b/target/linux/ramips/image/Makefile @@ -295,10 +295,36 @@ define BuildFirmware/Gemtek/squashfs endef BuildFirmware/Gemtek/initramfs=$(call BuildFirmware/OF/initramfs,$(1),$(2),$(3)) +# Airlink101 AR670W -- LZMA without uImage header +define BuildFirmware/AR670W/squashfs + $(call PatchKernelLzmaDtb,$(2),$(3),$(5)) + + $(eval output_name=$(IMG_PREFIX)-$(2)-$(1)-$(if $(4),$(4),sysupgrade).bin) + $(eval factory_name=$(IMG_PREFIX)-$(2)-$(1)-factory.bin) + + ( dd if=$(KDIR)/vmlinux-$(2).bin.lzma bs=65536 \ + conv=sync; dd if=$(KDIR)/root.$(1) ) > $(KDIR)/$(output_name) + + $(call prepare_generic_squashfs,$(KDIR)/$(output_name)) + + if [ `stat -c%s "$(KDIR)/$(output_name)"` \ + -gt $(ralink_default_fw_size_4M) ]; then \ + echo "Warning: $(KDIR)/$(output_name) is too big" >&2; \ + else \ + mkwrgimg -i $(KDIR)/$(output_name) \ + -d "/dev/mtdblock/2" \ + -s "wrgn16a_airlink_ar670w" \ + -o $(BIN_DIR)/$(factory_name); \ + $(CP) $(KDIR)/$(output_name) $(BIN_DIR)/$(output_name); \ + fi +endef + # # RT288X Profiles # +Image/Build/Profile/AR670W=$(call BuildFirmware/AR670W/$(1),$(1),ar670w,AR670W) + Image/Build/Profile/AR725W=$(call BuildFirmware/Gemtek/$(1),$(1),ar725w,AR725W) # 0x790000 @@ -313,6 +339,7 @@ Image/Build/Profile/WLITX4AG300N=$(call BuildFirmware/Default4M/$(1),$(1),wli-tx ifeq ($(SUBTARGET),rt288x) define Image/Build/Profile/Default + $(call Image/Build/Profile/AR670W,$(1)) $(call Image/Build/Profile/AR725W,$(1)) $(call Image/Build/Profile/F5D8235V1,$(1)) $(call Image/Build/Profile/RTN15,$(1)) diff --git a/target/linux/ramips/rt288x/config-3.14 b/target/linux/ramips/rt288x/config-3.14 index 44bb310..9a95186 100644 --- a/target/linux/ramips/rt288x/config-3.14 +++ b/target/linux/ramips/rt288x/config-3.14 @@ -107,6 +107,7 @@ CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_M25P80=y CONFIG_MTD_PHYSMAP=y CONFIG_MTD_SPLIT_FIRMWARE=y +CONFIG_MTD_SPLIT_LZMA_FW=y CONFIG_MTD_UIMAGE_SPLIT=y CONFIG_NEED_DMA_MAP_STATE=y CONFIG_NEED_PER_CPU_KM=y |