Netgear WG302 v2 / WAG302 v2 support

SVN-Revision: 6830

3 files changed, 271 insertions, 2 deletions

diff --git a/target/linux/ixp4xx-2.6/config/default b/target/linux/ixp4xx-2.6/config/default
index eceddf9..3e3cb55 100644
--- a/target/linux/ixp4xx-2.6/config/default
+++ b/target/linux/ixp4xx-2.6/config/default
@@ -18,8 +18,6 @@ CONFIG_ARCH_AVILA=y
 # CONFIG_ARCH_INTEGRATOR is not set
 # CONFIG_ARCH_IOP32X is not set
 # CONFIG_ARCH_IOP33X is not set
-CONFIG_MACH_PRONGHORN=y
-CONFIG_MACH_PRONGHORNMETRO=y
 CONFIG_ARCH_IXDP425=y
 CONFIG_ARCH_IXDP4XX=y
 # CONFIG_ARCH_IXP2000 is not set
@@ -221,6 +219,9 @@ CONFIG_MACH_GATEWAY7001=y
 # CONFIG_MACH_IXDPG425 is not set
 CONFIG_MACH_NAS100D=y
 CONFIG_MACH_NSLU2=y
+CONFIG_MACH_PRONGHORN=y
+CONFIG_MACH_PRONGHORNMETRO=y
+CONFIG_MACH_WG302V2=y
 # CONFIG_MAC_PARTITION is not set
 # CONFIG_MINIX_FS is not set
 CONFIG_MINI_FO=y
diff --git a/target/linux/ixp4xx-2.6/patches/300-wg302v2.patch b/target/linux/ixp4xx-2.6/patches/300-wg302v2.patch
new file mode 100644
index 0000000..fc3de40
--- /dev/null
+++ b/target/linux/ixp4xx-2.6/patches/300-wg302v2.patch
@@ -0,0 +1,231 @@
+diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig
+--- linux-2.6.19.2/arch/arm/mach-ixp4xx/Kconfig	2007-04-02 16:09:06.000000000 +0200
++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Kconfig	2007-04-02 16:01:25.000000000 +0200
+@@ -41,6 +41,14 @@
+ 	  7001 Access Point. For more information on this platform,
+ 	  see http://openwrt.org
+ 
++config MACH_WG302V2
++	bool "Netgear WG302 v2 / WAG302 v2"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support Netgear's 
++	  WG302 v2 or WAG302 v2 Access Points. For more information
++	  on this platform, see http://openwrt.org
++
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile
+--- linux-2.6.19.2/arch/arm/mach-ixp4xx/Makefile	2007-04-02 16:09:06.000000000 +0200
++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/Makefile	2007-04-02 16:09:25.000000000 +0200
+@@ -12,6 +12,7 @@
+ obj-pci-$(CONFIG_MACH_NSLU2)		+= nslu2-pci.o
+ obj-pci-$(CONFIG_MACH_NAS100D)		+= nas100d-pci.o
+ obj-pci-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-pci.o
++obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302v2-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -22,5 +23,6 @@
+ obj-$(CONFIG_MACH_NSLU2)	+= nslu2-setup.o nslu2-power.o
+ obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o nas100d-power.o
+ obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
++obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/wg302v2-pci.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wg302v2-pci.c
+--- linux-2.6.19.2/arch/arm/mach-ixp4xx/wg302v2-pci.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wg302v2-pci.c	2007-04-02 16:00:12.000000000 +0200
+@@ -0,0 +1,68 @@
++/*
++ * arch/arch/mach-ixp4xx/wg302v2-pci.c
++ *
++ * PCI setup routines for the Netgear WG302 v2 and WAG302 v2
++ *
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Software, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <asm/hardware.h>
++#include <asm/irq.h>
++
++#include <asm/mach/pci.h>
++
++extern void ixp4xx_pci_preinit(void);
++extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
++extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
++
++void __init wg302v2_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO8, IRQT_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO9, IRQT_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init wg302v2_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 1)
++		return IRQ_IXP4XX_GPIO8;
++	else if (slot == 2)
++		return IRQ_IXP4XX_GPIO9;
++	else return -1;
++}
++
++struct hw_pci wg302v2_pci __initdata = {
++	.nr_controllers = 1,
++	.preinit =        wg302v2_pci_preinit,
++	.swizzle =        pci_std_swizzle,
++	.setup =          ixp4xx_setup,
++	.scan =           ixp4xx_scan_bus,
++	.map_irq =        wg302v2_map_irq,
++};
++
++int __init wg302v2_pci_init(void)
++{
++	if (machine_is_wg302v2())
++		pci_common_init(&wg302v2_pci);
++	return 0;
++}
++
++subsys_initcall(wg302v2_pci_init);
+diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/wg302v2-setup.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wg302v2-setup.c
+--- linux-2.6.19.2/arch/arm/mach-ixp4xx/wg302v2-setup.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wg302v2-setup.c	2007-04-02 16:08:57.000000000 +0200
+@@ -0,0 +1,107 @@
++/*
++ * arch/arm/mach-ixp4xx/wg302-setup.c
++ *
++ * Board setup for the Netgear WG302 v2 and WAG302 v2
++ *
++ * based on coyote-setup.c:
++ *     Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++
++#include <asm/types.h>
++#include <asm/setup.h>
++#include <asm/memory.h>
++#include <asm/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data wg302v2_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource wg302v2_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device wg302v2_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &wg302v2_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &wg302v2_flash_resource,
++};
++
++static struct resource wg302v2_uart_resource = {
++	.start	= IXP4XX_UART2_BASE_PHYS,
++	.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++	.flags	= IORESOURCE_MEM,
++};
++
++static struct plat_serial8250_port wg302v2_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device wg302v2_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev			= {
++		.platform_data	= wg302v2_uart_data,
++	},
++	.num_resources	= 1,
++	.resource	= &wg302v2_uart_resource,
++};
++
++static struct platform_device *wg302v2_devices[] __initdata = {
++	&wg302v2_flash,
++	&wg302v2_uart,
++};
++
++static void __init wg302v2_init(void)
++{
++	ixp4xx_sys_init();
++
++	wg302v2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	wg302v2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++	platform_add_devices(wg302v2_devices, ARRAY_SIZE(wg302v2_devices));
++}
++
++#ifdef CONFIG_ARCH_WG302V2
++MACHINE_START(WG302V2, "Netgear WG302 v2 / WAG302 v2")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= wg302v2_init,
++MACHINE_END
++#endif
+diff -Nur linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h
+--- linux-2.6.19.2/include/asm-arm/arch-ixp4xx/uncompress.h	2007-04-02 16:09:06.000000000 +0200
++++ linux-2.6.19.2-owrt/include/asm-arm/arch-ixp4xx/uncompress.h	2007-04-02 16:02:04.000000000 +0200
+@@ -40,7 +40,7 @@
+ 	/*
+ 	 * Some boards are using UART2 as console
+ 	 */
+-	if (machine_is_adi_coyote() || machine_is_gtwx5715() || machine_is_gateway7001())
++	if (machine_is_adi_coyote() || machine_is_gtwx5715() || machine_is_gateway7001() || machine_is_wg302v2())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
diff --git a/target/linux/ixp4xx-2.6/patches/310-wg302v2_setup_mac.patch b/target/linux/ixp4xx-2.6/patches/310-wg302v2_setup_mac.patch
new file mode 100644
index 0000000..27616e1
--- /dev/null
+++ b/target/linux/ixp4xx-2.6/patches/310-wg302v2_setup_mac.patch
@@ -0,0 +1,37 @@
+diff -Nur linux-2.6.19.2/arch/arm/mach-ixp4xx/wg302v2-setup.c linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wg302v2-setup.c
+--- linux-2.6.19.2/arch/arm/mach-ixp4xx/wg302v2-setup.c	2007-04-02 16:06:02.000000000 +0200
++++ linux-2.6.19.2-owrt/arch/arm/mach-ixp4xx/wg302v2-setup.c	2007-03-05 11:57:24.000000000 +0100
+@@ -75,9 +75,33 @@
+ 	.resource	= &wg302v2_uart_resource,
+ };
+ 
++static struct resource res_mac0 = {
++	.start		= IXP4XX_EthB_BASE_PHYS,
++	.end		= IXP4XX_EthB_BASE_PHYS + 0x1ff,
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct mac_plat_info plat_mac0 = {
++	.npe_id		= 1,
++	.phy_id		= 8,
++	.eth_id		= 0,
++	.rxq_id		= 27,
++	.txq_id		= 24,
++	.rxdoneq_id	= 4,
++};
++
++static struct platform_device mac0 = {
++	.name		= "ixp4xx_mac",
++	.id		= 0,
++	.dev.platform_data = &plat_mac0,
++	.num_resources	= 1,
++	.resource	= &res_mac0,
++};
++
+ static struct platform_device *wg302v2_devices[] __initdata = {
+ 	&wg302v2_flash,
+ 	&wg302v2_uart,
++	&mac0,
+ };
+ 
+ static void __init wg302v2_init(void)