summaryrefslogtreecommitdiff
path: root/package/network/utils/iw
diff options
context:
space:
mode:
authorFelix Fietkau <nbd@openwrt.org>2014-09-27 21:19:18 +0000
committerFelix Fietkau <nbd@openwrt.org>2014-09-27 21:19:18 +0000
commitd27893122db78513393105bc3e4873d068822454 (patch)
treed90fc9cb2241fd2be9f84e699031534a73bcd567 /package/network/utils/iw
parent61f960071d8c5f3cfd877d2137f39c974a432e4d (diff)
downloadmtk-20170518-d27893122db78513393105bc3e4873d068822454.zip
mtk-20170518-d27893122db78513393105bc3e4873d068822454.tar.gz
mtk-20170518-d27893122db78513393105bc3e4873d068822454.tar.bz2
iw: sync nl80211.h
Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 42688
Diffstat (limited to 'package/network/utils/iw')
-rw-r--r--package/network/utils/iw/patches/001-nl80211_h_sync.patch193
1 files changed, 181 insertions, 12 deletions
diff --git a/package/network/utils/iw/patches/001-nl80211_h_sync.patch b/package/network/utils/iw/patches/001-nl80211_h_sync.patch
index 4f780fb..64e3305 100644
--- a/package/network/utils/iw/patches/001-nl80211_h_sync.patch
+++ b/package/network/utils/iw/patches/001-nl80211_h_sync.patch
@@ -10,7 +10,40 @@
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
* command may be used with the corresponding cookie to cancel the wait
* time if it is known that it is no longer necessary.
-@@ -1525,10 +1528,10 @@ enum nl80211_commands {
+@@ -719,6 +722,22 @@
+ * QoS mapping is relevant for IP packets, it is only valid during an
+ * association. This is cleared on disassociation and AP restart.
+ *
++ * @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given
++ * %NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO
++ * and %NL80211_ATTR_ADMITTED_TIME parameters.
++ * Note that the action frame handshake with the AP shall be handled by
++ * userspace via the normal management RX/TX framework, this only sets
++ * up the TX TS in the driver/device.
++ * If the admitted time attribute is not added then the request just checks
++ * if a subsequent setup could be successful, the intent is to use this to
++ * avoid setting up a session with the AP when local restrictions would
++ * make that impossible. However, the subsequent "real" setup may still
++ * fail even if the check was successful.
++ * @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID
++ * and %NL80211_ATTR_MAC parameters. It isn't necessary to call this
++ * before removing a station entry entirely, or before disassociating
++ * or similar, cleanup will happen in the driver/device in this case.
++ *
+ * @NL80211_CMD_MAX: highest used command number
+ * @__NL80211_CMD_AFTER_LAST: internal use
+ */
+@@ -890,6 +909,9 @@ enum nl80211_commands {
+
+ NL80211_CMD_SET_QOS_MAP,
+
++ NL80211_CMD_ADD_TX_TS,
++ NL80211_CMD_DEL_TX_TS,
++
+ /* add new commands above here */
+
+ /* used to define NL80211_CMD_MAX below */
+@@ -1525,10 +1547,10 @@ enum nl80211_commands {
* operation).
* @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
* for the time while performing a channel switch.
@@ -25,7 +58,7 @@
*
* @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
* As specified in the &enum nl80211_rxmgmt_flags.
-@@ -1576,9 +1579,21 @@ enum nl80211_commands {
+@@ -1576,9 +1598,49 @@ enum nl80211_commands {
* advertise values that cannot always be met. In such cases, an attempt
* to add a new station entry with @NL80211_CMD_NEW_STATION may fail.
*
@@ -41,13 +74,41 @@
+ * creation then the new interface will be owned by the netlink socket
+ * that created it and will be destroyed when the socket is closed
+ *
++ * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is
++ * the TDLS link initiator.
++ *
++ * @NL80211_ATTR_USE_RRM: flag for indicating whether the current connection
++ * shall support Radio Resource Measurements (11k). This attribute can be
++ * used with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests.
++ * User space applications are expected to use this flag only if the
++ * underlying device supports these minimal RRM features:
++ * %NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES,
++ * %NL80211_FEATURE_QUIET,
++ * If this flag is used, driver must add the Power Capabilities IE to the
++ * association request. In addition, it must also set the RRM capability
++ * flag in the association request's Capability Info field.
++ *
++ * @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout
++ * estimation algorithm (dynack). In order to activate dynack
++ * %NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower
++ * drivers to indicate dynack capability. Dynack is automatically disabled
++ * setting valid value for coverage class.
++ *
++ * @NL80211_ATTR_TSID: a TSID value (u8 attribute)
++ * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute)
++ * @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds
++ * (per second) (u16 attribute)
++ *
++ * @NL80211_ATTR_SMPS_MODE: SMPS mode to use (ap mode). see
++ * &enum nl80211_smps_mode.
++ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ * transmit power to stay within regulatory limits. u32, dBi.
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
-@@ -1914,6 +1929,13 @@ enum nl80211_attrs {
+@@ -1914,6 +1976,25 @@ enum nl80211_attrs {
NL80211_ATTR_TDLS_PEER_CAPABILITY,
@@ -56,12 +117,24 @@
+ NL80211_ATTR_CSA_C_OFFSETS_TX,
+ NL80211_ATTR_MAX_CSA_COUNTERS,
+
++ NL80211_ATTR_TDLS_INITIATOR,
++
++ NL80211_ATTR_USE_RRM,
++
++ NL80211_ATTR_WIPHY_DYN_ACK,
++
++ NL80211_ATTR_TSID,
++ NL80211_ATTR_USER_PRIO,
++ NL80211_ATTR_ADMITTED_TIME,
++
++ NL80211_ATTR_SMPS_MODE,
++
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
-@@ -2182,6 +2204,8 @@ enum nl80211_sta_bss_param {
+@@ -2182,6 +2263,8 @@ enum nl80211_sta_bss_param {
* Contains a nested array of signal strength attributes (u8, dBm)
* @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
* Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
@@ -70,7 +143,7 @@
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
-@@ -2213,6 +2237,7 @@ enum nl80211_sta_info {
+@@ -2213,6 +2296,7 @@ enum nl80211_sta_info {
NL80211_STA_INFO_TX_BYTES64,
NL80211_STA_INFO_CHAIN_SIGNAL,
NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
@@ -78,7 +151,7 @@
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
-@@ -2336,9 +2361,34 @@ enum nl80211_band_attr {
+@@ -2336,9 +2420,34 @@ enum nl80211_band_attr {
* using this channel as the primary or any of the secondary channels
* isn't possible
* @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
@@ -113,7 +186,7 @@
*/
enum nl80211_frequency_attr {
__NL80211_FREQUENCY_ATTR_INVALID,
-@@ -2355,6 +2405,10 @@ enum nl80211_frequency_attr {
+@@ -2355,6 +2464,10 @@ enum nl80211_frequency_attr {
NL80211_FREQUENCY_ATTR_NO_80MHZ,
NL80211_FREQUENCY_ATTR_NO_160MHZ,
NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
@@ -124,7 +197,7 @@
/* keep last */
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
-@@ -2573,10 +2627,13 @@ enum nl80211_dfs_regions {
+@@ -2573,10 +2686,13 @@ enum nl80211_dfs_regions {
* present has been registered with the wireless core that
* has listed NL80211_FEATURE_CELL_BASE_REG_HINTS as a
* supported feature.
@@ -138,7 +211,50 @@
};
/**
-@@ -3650,6 +3707,8 @@ enum nl80211_iface_limit_attrs {
+@@ -2998,14 +3114,20 @@ enum nl80211_bss_scan_width {
+ * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
+ * @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
+ * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
++ * (if @NL80211_BSS_PRESP_DATA is present then this is known to be
++ * from a probe response, otherwise it may be from the same beacon
++ * that the NL80211_BSS_BEACON_TSF will be from)
+ * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
+ * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
+ * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
+ * raw information elements from the probe response/beacon (bin);
+- * if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are
+- * from a Probe Response frame; otherwise they are from a Beacon frame.
++ * if the %NL80211_BSS_BEACON_IES attribute is present and the data is
++ * different then the IEs here are from a Probe Response frame; otherwise
++ * they are from a Beacon frame.
+ * However, if the driver does not indicate the source of the IEs, these
+ * IEs may be from either frame subtype.
++ * If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the
++ * data here is known to be from a probe response, without any heuristics.
+ * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
+ * in mBm (100 * dBm) (s32)
+ * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
+@@ -3017,6 +3139,10 @@ enum nl80211_bss_scan_width {
+ * yet been received
+ * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
+ * (u32, enum nl80211_bss_scan_width)
++ * @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
++ * (not present if no beacon frame has been received yet)
++ * @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
++ * @NL80211_BSS_TSF is known to be from a probe response (flag attribute)
+ * @__NL80211_BSS_AFTER_LAST: internal
+ * @NL80211_BSS_MAX: highest BSS attribute
+ */
+@@ -3034,6 +3160,8 @@ enum nl80211_bss {
+ NL80211_BSS_SEEN_MS_AGO,
+ NL80211_BSS_BEACON_IES,
+ NL80211_BSS_CHAN_WIDTH,
++ NL80211_BSS_BEACON_TSF,
++ NL80211_BSS_PRESP_DATA,
+
+ /* keep last */
+ __NL80211_BSS_AFTER_LAST,
+@@ -3650,6 +3778,8 @@ enum nl80211_iface_limit_attrs {
* different channels may be used within this group.
* @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap
* of supported channel widths for radar detection.
@@ -147,7 +263,7 @@
* @NUM_NL80211_IFACE_COMB: number of attributes
* @MAX_NL80211_IFACE_COMB: highest attribute number
*
-@@ -3683,6 +3742,7 @@ enum nl80211_if_combination_attrs {
+@@ -3683,6 +3813,7 @@ enum nl80211_if_combination_attrs {
NL80211_IFACE_COMB_STA_AP_BI_MATCH,
NL80211_IFACE_COMB_NUM_CHANNELS,
NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS,
@@ -155,21 +271,74 @@
/* keep last */
NUM_NL80211_IFACE_COMB,
-@@ -3893,6 +3953,9 @@ enum nl80211_ap_sme_features {
+@@ -3893,6 +4024,29 @@ enum nl80211_ap_sme_features {
* interface. An active monitor interface behaves like a normal monitor
* interface, but gets added to the driver. It ensures that incoming
* unicast packets directed at the configured interface address get ACKed.
+ * @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
+ * channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
+ * lifetime of a BSS.
++ * @NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES: This device adds a DS Parameter
++ * Set IE to probe requests.
++ * @NL80211_FEATURE_WFA_TPC_IE_IN_PROBES: This device adds a WFA TPC Report IE
++ * to probe requests.
++ * @NL80211_FEATURE_QUIET: This device, in client mode, supports Quiet Period
++ * requests sent to it by an AP.
++ * @NL80211_FEATURE_TX_POWER_INSERTION: This device is capable of inserting the
++ * current tx power value into the TPC Report IE in the spectrum
++ * management TPC Report action frame, and in the Radio Measurement Link
++ * Measurement Report action frame.
++ * @NL80211_FEATURE_ACKTO_ESTIMATION: This driver supports dynamic ACK timeout
++ * estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used
++ * to enable dynack.
++ * @NL80211_FEATURE_STATIC_SMPS: Device supports static spatial
++ * multiplexing powersave, ie. can turn off all but one chain
++ * even on HT connections that should be using more chains.
++ * @NL80211_FEATURE_DYNAMIC_SMPS: Device supports dynamic spatial
++ * multiplexing powersave, ie. can turn off all but one chain
++ * and then wake the rest up as required after, for example,
++ * rts/cts handshake.
*/
enum nl80211_feature_flags {
NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
-@@ -3913,6 +3976,7 @@ enum nl80211_feature_flags {
+@@ -3913,6 +4067,14 @@ enum nl80211_feature_flags {
NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15,
NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
+ NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18,
++ NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES = 1 << 19,
++ NL80211_FEATURE_WFA_TPC_IE_IN_PROBES = 1 << 20,
++ NL80211_FEATURE_QUIET = 1 << 21,
++ NL80211_FEATURE_TX_POWER_INSERTION = 1 << 22,
++ NL80211_FEATURE_ACKTO_ESTIMATION = 1 << 23,
++ NL80211_FEATURE_STATIC_SMPS = 1 << 24,
++ NL80211_FEATURE_DYNAMIC_SMPS = 1 << 25,
+ };
+
+ /**
+@@ -3987,6 +4149,25 @@ enum nl80211_acl_policy {
};
/**
++ * enum nl80211_smps_mode - SMPS mode
++ *
++ * Requested SMPS mode (for AP mode)
++ *
++ * @NL80211_SMPS_OFF: SMPS off (use all antennas).
++ * @NL80211_SMPS_STATIC: static SMPS (use a single antenna)
++ * @NL80211_SMPS_DYNAMIC: dynamic smps (start with a single antenna and
++ * turn on other antennas after CTS/RTS).
++ */
++enum nl80211_smps_mode {
++ NL80211_SMPS_OFF,
++ NL80211_SMPS_STATIC,
++ NL80211_SMPS_DYNAMIC,
++
++ __NL80211_SMPS_AFTER_LAST,
++ NL80211_SMPS_MAX = __NL80211_SMPS_AFTER_LAST - 1
++};
++
++/**
+ * enum nl80211_radar_event - type of radar event for DFS operation
+ *
+ * Type of event to be used with NL80211_ATTR_RADAR_EVENT to inform userspace