summaryrefslogtreecommitdiff
path: root/package
diff options
context:
space:
mode:
authorChristian Lamparter <chunkeey@gmail.com>2018-03-07 09:13:10 +0100
committerMathias Kresin <dev@kresin.me>2018-03-14 19:04:51 +0100
commit87c42101cfb001b4bd418d1201fa4d8c822dc77b (patch)
tree4d73703558bea4d4a9225d723dee773586611435 /package
parent43be5087a915727e7dcb3459e2221f094c70811b (diff)
downloadmtk-20170518-87c42101cfb001b4bd418d1201fa4d8c822dc77b.zip
mtk-20170518-87c42101cfb001b4bd418d1201fa4d8c822dc77b.tar.gz
mtk-20170518-87c42101cfb001b4bd418d1201fa4d8c822dc77b.tar.bz2
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'package')
-rw-r--r--package/firmware/ipq-wifi/Makefile3
-rw-r--r--package/firmware/ipq-wifi/board-asus_rt-ac58u.bin0
2 files changed, 2 insertions, 1 deletions
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 3f929bc..39d29a4 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -13,7 +13,7 @@ endef
define Build/Compile
endef
-ALLWIFIBOARDS:=avm_fritzbox-4040 glinet_gl-b1300
+ALLWIFIBOARDS:=asus_rt-ac58u avm_fritzbox-4040 glinet_gl-b1300
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
@@ -47,6 +47,7 @@ Don't install it for any other device!
PREV_BOARD+=ipq-wifi-$(1)
endef
+$(eval $(call generate-ipq-wifi-package,asus_rt-ac58u,board-asus_rt-ac58u.bin,ASUS RT-AC58U))
$(eval $(call generate-ipq-wifi-package,avm_fritzbox-4040,board-avm_fritzbox-4040.bin,AVM FRITZ!Box 4040))
$(eval $(call generate-ipq-wifi-package,glinet_gl-b1300,board-glinet_gl-b1300.bin,GL.iNet GL-B1300))
diff --git a/package/firmware/ipq-wifi/board-asus_rt-ac58u.bin b/package/firmware/ipq-wifi/board-asus_rt-ac58u.bin
new file mode 100644
index 0000000..e69de29
--- /dev/null
+++ b/package/firmware/ipq-wifi/board-asus_rt-ac58u.bin