adm5120: nuke 2.6.30 stuff

SVN-Revision: 20445

16 files changed, 0 insertions, 1293 deletions

diff --git a/target/linux/adm5120/patches-2.6.30/001-adm5120.patch b/target/linux/adm5120/patches-2.6.30/001-adm5120.patch
deleted file mode 100644
index 5547234..0000000
--- a/target/linux/adm5120/patches-2.6.30/001-adm5120.patch
+++ /dev/null
@@ -1,57 +0,0 @@
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -19,6 +19,21 @@ choice
- 	prompt "System type"
- 	default SGI_IP22
- 
-+config ADM5120
-+	bool "Infineon/ADMtek ADM5120 SoC based machines"
-+	select CEVT_R4K
-+	select CSRC_R4K
-+	select SYS_HAS_CPU_MIPS32_R1
-+	select SYS_HAS_EARLY_PRINTK
-+	select DMA_NONCOHERENT
-+	select IRQ_CPU
-+	select SYS_SUPPORTS_LITTLE_ENDIAN
-+	select SYS_SUPPORTS_BIG_ENDIAN
-+	select SYS_SUPPORTS_32BIT_KERNEL
-+	select ARCH_REQUIRE_GPIOLIB
-+	select SWAP_IO_SPACE if CPU_BIG_ENDIAN
-+	select MIPS_MACHINE
-+
- config MACH_ALCHEMY
- 	bool "Alchemy processor based machines"
- 
-@@ -633,6 +648,7 @@ config CAVIUM_OCTEON_REFERENCE_BOARD
- 
- endchoice
- 
-+source "arch/mips/adm5120/Kconfig"
- source "arch/mips/alchemy/Kconfig"
- source "arch/mips/basler/excite/Kconfig"
- source "arch/mips/jazz/Kconfig"
---- a/arch/mips/Makefile
-+++ b/arch/mips/Makefile
-@@ -181,6 +181,22 @@ cflags-$(CONFIG_MACH_JAZZ)	+= -I$(srctre
- load-$(CONFIG_MACH_JAZZ)	+= 0xffffffff80080000
- 
- #
-+# Infineon/ADMtek ADM5120
-+#
-+libs-$(CONFIG_ADM5120)			+= arch/mips/adm5120/prom/
-+core-$(CONFIG_ADM5120)			+= arch/mips/adm5120/common/
-+core-$(CONFIG_ADM5120_OEM_CELLVISION)	+= arch/mips/adm5120/cellvision/
-+core-$(CONFIG_ADM5120_OEM_COMPEX)	+= arch/mips/adm5120/compex/
-+core-$(CONFIG_ADM5120_OEM_EDIMAX)	+= arch/mips/adm5120/edimax/
-+core-$(CONFIG_ADM5120_OEM_INFINEON)	+= arch/mips/adm5120/infineon/
-+core-$(CONFIG_ADM5120_OEM_MIKROTIK)	+= arch/mips/adm5120/mikrotik/
-+core-$(CONFIG_ADM5120_OEM_MOTOROLA)	+= arch/mips/adm5120/motorola/
-+core-$(CONFIG_ADM5120_OEM_OSBRIDGE)	+= arch/mips/adm5120/osbridge/
-+core-$(CONFIG_ADM5120_OEM_ZYXEL)	+= arch/mips/adm5120/zyxel/
-+cflags-$(CONFIG_ADM5120)		+= -I$(srctree)/arch/mips/include/asm/mach-adm5120
-+load-$(CONFIG_ADM5120)			+= 0xffffffff80001000
-+
-+#
- # Common Alchemy Au1x00 stuff
- #
- core-$(CONFIG_SOC_AU1X00)	+= arch/mips/alchemy/common/
diff --git a/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch b/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch
deleted file mode 100644
index 97f5b96..0000000
--- a/target/linux/adm5120/patches-2.6.30/002-adm5120_flash.patch
+++ /dev/null
@@ -1,21 +0,0 @@
---- a/drivers/mtd/maps/Kconfig
-+++ b/drivers/mtd/maps/Kconfig
-@@ -562,4 +562,8 @@ config MTD_VMU
- 	  To build this as a module select M here, the module will be called
- 	  vmu-flash.
- 
-+config MTD_ADM5120
-+	tristate "Map driver for ADM5120 based boards"
-+	depends on ADM5120
-+
- endmenu
---- a/drivers/mtd/maps/Makefile
-+++ b/drivers/mtd/maps/Makefile
-@@ -42,6 +42,7 @@ obj-$(CONFIG_MTD_DBOX2)		+= dbox2-flash.
- obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
- obj-$(CONFIG_MTD_PCI)		+= pci.o
- obj-$(CONFIG_MTD_ALCHEMY)       += alchemy-flash.o
-+obj-$(CONFIG_MTD_ADM5120)      	+= adm5120-flash.o
- obj-$(CONFIG_MTD_AUTCPU12)	+= autcpu12-nvram.o
- obj-$(CONFIG_MTD_EDB7312)	+= edb7312.o
- obj-$(CONFIG_MTD_IMPA7)		+= impa7.o
diff --git a/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch b/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch
deleted file mode 100644
index 771dd5f..0000000
--- a/target/linux/adm5120/patches-2.6.30/003-adm5120_switch.patch
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/drivers/net/Kconfig
-+++ b/drivers/net/Kconfig
-@@ -612,6 +612,10 @@ config MIPS_AU1X00_ENET
- 	  If you have an Alchemy Semi AU1X00 based system
- 	  say Y.  Otherwise, say N.
- 
-+config ADM5120_ENET
-+	tristate "ADM5120 Ethernet switch support"
-+	depends on ADM5120
-+
- config SGI_IOC3_ETH
- 	bool "SGI IOC3 Ethernet"
- 	depends on PCI && SGI_IP27
---- a/drivers/net/Makefile
-+++ b/drivers/net/Makefile
-@@ -195,6 +195,7 @@ obj-$(CONFIG_SC92031) += sc92031.o
- # This is also a 82596 and should probably be merged
- obj-$(CONFIG_LP486E) += lp486e.o
- 
-+obj-$(CONFIG_ADM5120_ENET) += adm5120sw.o
- obj-$(CONFIG_ETH16I) += eth16i.o
- obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
- obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
diff --git a/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch b/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch
deleted file mode 100644
index ca81a92..0000000
--- a/target/linux/adm5120/patches-2.6.30/005-adm5120_usb.patch
+++ /dev/null
@@ -1,33 +0,0 @@
---- a/drivers/usb/Makefile
-+++ b/drivers/usb/Makefile
-@@ -9,6 +9,7 @@ obj-$(CONFIG_USB)		+= core/
- obj-$(CONFIG_USB_MON)		+= mon/
- 
- obj-$(CONFIG_PCI)		+= host/
-+obj-$(CONFIG_USB_ADM5120_HCD)	+= host/
- obj-$(CONFIG_USB_EHCI_HCD)	+= host/
- obj-$(CONFIG_USB_ISP116X_HCD)	+= host/
- obj-$(CONFIG_USB_OHCI_HCD)	+= host/
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -4,6 +4,10 @@
- comment "USB Host Controller Drivers"
- 	depends on USB
- 
-+config USB_ADM5120_HCD
-+	tristate "ADM5120 HCD support (EXPERIMENTAL)"
-+	depends on USB && ADM5120 && EXPERIMENTAL
-+
- config USB_C67X00_HCD
- 	tristate "Cypress C67x00 HCD support"
- 	depends on USB
---- a/drivers/usb/host/Makefile
-+++ b/drivers/usb/host/Makefile
-@@ -17,6 +17,7 @@ obj-$(CONFIG_USB_WHCI_HCD)	+= whci/
- 
- obj-$(CONFIG_PCI)		+= pci-quirks.o
- 
-+obj-$(CONFIG_USB_ADM5120_HCD)	+= adm5120-hcd.o
- obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
- obj-$(CONFIG_USB_OXU210HP_HCD)	+= oxu210hp-hcd.o
- obj-$(CONFIG_USB_ISP116X_HCD)	+= isp116x-hcd.o
diff --git a/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch b/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch
deleted file mode 100644
index 7869c97..0000000
--- a/target/linux/adm5120/patches-2.6.30/007-adm5120_pci.patch
+++ /dev/null
@@ -1,19 +0,0 @@
---- a/arch/mips/pci/Makefile
-+++ b/arch/mips/pci/Makefile
-@@ -52,3 +52,4 @@ obj-$(CONFIG_VICTOR_MPC30X)	+= fixup-mpc
- obj-$(CONFIG_ZAO_CAPCELLA)	+= fixup-capcella.o
- obj-$(CONFIG_WR_PPMC)		+= fixup-wrppmc.o
- obj-$(CONFIG_MIKROTIK_RB532)	+= pci-rc32434.o ops-rc32434.o fixup-rc32434.o
-+obj-$(CONFIG_ADM5120)		+= pci-adm5120.o
---- a/include/linux/pci_ids.h
-+++ b/include/linux/pci_ids.h
-@@ -1764,6 +1764,9 @@
- #define PCI_VENDOR_ID_ESDGMBH		0x12fe
- #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
- 
-+#define PCI_VENDOR_ID_ADMTEK		0x1317
-+#define PCI_DEVICE_ID_ADMTEK_ADM5120	0x5120
-+
- #define PCI_VENDOR_ID_SIIG		0x131f
- #define PCI_SUBVENDOR_ID_SIIG		0x131f
- #define PCI_DEVICE_ID_SIIG_1S_10x_550	0x1000
diff --git a/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch b/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch
deleted file mode 100644
index 4778dea..0000000
--- a/target/linux/adm5120/patches-2.6.30/009-adm5120_leds_switch_trigger.patch
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/drivers/leds/Kconfig
-+++ b/drivers/leds/Kconfig
-@@ -306,4 +306,12 @@ config LEDS_TRIGGER_NETDEV
- 	  This allows LEDs to be controlled by network device activity.
- 	  If unsure, say Y.
- 
-+config LEDS_TRIGGER_ADM5120_SWITCH
-+	tristate "LED ADM5120 Switch Port Status Trigger"
-+	depends on LEDS_TRIGGERS && ADM5120
-+	help
-+	  This allows LEDs to be controlled by the port states of
-+	  the ADM5120 built-in Ethernet Switch
-+	  If unsure, say N.
-+
- endif # NEW_LEDS
---- a/drivers/leds/Makefile
-+++ b/drivers/leds/Makefile
-@@ -40,3 +40,4 @@ obj-$(CONFIG_LEDS_TRIGGER_GPIO)		+= ledt
- obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON)	+= ledtrig-default-on.o
- obj-$(CONFIG_LEDS_TRIGGER_MORSE)	+= ledtrig-morse.o
- obj-$(CONFIG_LEDS_TRIGGER_NETDEV)      += ledtrig-netdev.o
-+obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o
diff --git a/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch b/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch
deleted file mode 100644
index 60c3ab9..0000000
--- a/target/linux/adm5120/patches-2.6.30/101-cfi_fixup_macronix_bootloc.patch
+++ /dev/null
@@ -1,84 +0,0 @@
---- a/drivers/mtd/chips/cfi_cmdset_0002.c
-+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
-@@ -53,6 +53,12 @@
- #define AT49BV6416		0x00d6
- #define MANUFACTURER_SAMSUNG	0x00ec
- 
-+/* Macronix */
-+#define MX29LV160B	0x2249	/* MX29LV160 Bottom-boot chip */
-+#define MX29LV160T	0x22C4	/* MX29LV160 Top-boot chip */
-+#define MX29LV320B	0x22A8	/* MX29LV320 Bottom-boot chip */
-+#define MX29LV320T	0x22A7	/* MX29LV320 Top-boot chip */
-+
- static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
- static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
- static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
-@@ -293,6 +299,41 @@ static void fixup_M29W128G_write_buffer(
- 	}
- }
- 
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+/*
-+ * Some Macronix chips has no/bad bootblock information in the CFI table
-+ */
-+static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
-+{
-+	struct map_info *map = mtd->priv;
-+	struct cfi_private *cfi = map->fldrv_priv;
-+	struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
-+	__u8 t;
-+
-+	switch (cfi->id) {
-+	/* TODO: put affected chip ids here */
-+	case MX29LV160B:
-+	case MX29LV320B:
-+		t = 2;	/* Bottom boot */
-+		break;
-+	case MX29LV160T:
-+	case MX29LV320T:
-+		t = 3;	/* Top boot */
-+		break;
-+	default:
-+		return;
-+	}
-+
-+	if (extp->TopBottom == t)
-+		/* boot location detected by the CFI layer is correct */
-+		return;
-+
-+	extp->TopBottom = t;
-+	printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
-+		"to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
-+}
-+#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
-+
- static struct cfi_fixup cfi_fixup_table[] = {
- 	{ CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
- #ifdef AMD_BOOTLOC_BUG
-@@ -330,6 +371,9 @@ static struct cfi_fixup fixup_table[] = 
- 	 */
- 	{ CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip, NULL },
- 	{ CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock, NULL },
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+	{ MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
-+#endif
- 	{ 0, 0, NULL, NULL }
- };
- 
---- a/drivers/mtd/chips/Kconfig
-+++ b/drivers/mtd/chips/Kconfig
-@@ -198,6 +198,14 @@ config MTD_CFI_AMDSTD
- 	  provides support for one of those command sets, used on chips
- 	  including the AMD Am29LV320.
- 
-+config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+	bool "Fix boot-block location for Macronix flash chips"
-+	depends on MTD_CFI_AMDSTD
-+	help
-+	  Some Macronix flash chips have no/wrong boot-block location in the
-+	  CFI table, and the driver may detect the type incorrectly. Select
-+	  this if your board has such chip.
-+
- config MTD_CFI_STAA
- 	tristate "Support for ST (Advanced Architecture) flash chips"
- 	depends on MTD_GEN_PROBE
diff --git a/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch b/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch
deleted file mode 100644
index 55a201d..0000000
--- a/target/linux/adm5120/patches-2.6.30/102-jedec_pmc_39lvxxx_chips.patch
+++ /dev/null
@@ -1,68 +0,0 @@
---- a/drivers/mtd/chips/jedec_probe.c
-+++ b/drivers/mtd/chips/jedec_probe.c
-@@ -128,6 +128,10 @@
- #define UPD29F064115	0x221C
- 
- /* PMC */
-+#define PM39LV512	0x001B
-+#define PM39LV010	0x001C
-+#define PM39LV020	0x003D
-+#define PM39LV040	0x003E
- #define PM49FL002	0x006D
- #define PM49FL004	0x006E
- #define PM49FL008	0x006A
-@@ -1249,6 +1253,54 @@ static const struct amd_flash_info jedec
- 			ERASEINFO(0x02000,2),
- 			ERASEINFO(0x04000,1),
- 		}
-+        }, {
-+		.mfr_id		= MANUFACTURER_PMC,
-+		.dev_id		= PM39LV512,
-+		.name		= "PMC Pm39LV512",
-+		.devtypes	= CFI_DEVICETYPE_X8,
-+		.uaddr		= MTD_UADDR_0x0555_0x02AA,
-+		.dev_size	= SIZE_64KiB,
-+		.cmd_set	= P_ID_AMD_STD,
-+		.nr_regions	= 1,
-+		.regions	= {
-+			ERASEINFO(0x01000,16),
-+		}
-+        }, {
-+		.mfr_id		= MANUFACTURER_PMC,
-+		.dev_id		= PM39LV010,
-+		.name		= "PMC Pm39LV010",
-+		.devtypes	= CFI_DEVICETYPE_X8,
-+		.uaddr		= MTD_UADDR_0x0555_0x02AA,
-+		.dev_size	= SIZE_128KiB,
-+		.cmd_set	= P_ID_AMD_STD,
-+		.nr_regions	= 1,
-+		.regions	= {
-+			ERASEINFO(0x01000,32),
-+		}
-+        }, {
-+		.mfr_id		= MANUFACTURER_PMC,
-+		.dev_id		= PM39LV020,
-+		.name		= "PMC Pm39LV020",
-+		.devtypes	= CFI_DEVICETYPE_X8,
-+		.uaddr		= MTD_UADDR_0x0555_0x02AA,
-+		.dev_size	= SIZE_256KiB,
-+		.cmd_set	= P_ID_AMD_STD,
-+		.nr_regions	= 1,
-+		.regions	= {
-+			ERASEINFO(0x01000,64),
-+		}
-+        }, {
-+		.mfr_id		= MANUFACTURER_PMC,
-+		.dev_id		= PM39LV040,
-+		.name		= "PMC Pm39LV040",
-+		.devtypes	= CFI_DEVICETYPE_X8,
-+		.uaddr		= MTD_UADDR_0x0555_0x02AA,
-+		.dev_size	= SIZE_512KiB,
-+		.cmd_set	= P_ID_AMD_STD,
-+		.nr_regions	= 1,
-+		.regions	= {
-+			ERASEINFO(0x01000,128),
-+		}
- 	}, {
- 		.mfr_id		= MANUFACTURER_PMC,
- 		.dev_id		= PM49FL002,
diff --git a/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch b/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch
deleted file mode 100644
index 69f1035..0000000
--- a/target/linux/adm5120/patches-2.6.30/103-mtd_trxsplit.patch
+++ /dev/null
@@ -1,24 +0,0 @@
---- a/drivers/mtd/Kconfig
-+++ b/drivers/mtd/Kconfig
-@@ -63,6 +63,11 @@ config MTD_ROOTFS_SPLIT
- 	depends on MTD_PARTITIONS
- 	default y
- 
-+config MTD_TRXSPLIT
-+	bool "Automatically find and split TRX partitions"
-+	depends on MTD_PARTITIONS
-+	default n
-+
- config MTD_REDBOOT_PARTS
- 	tristate "RedBoot partition table parsing"
- 	depends on MTD_PARTITIONS
---- a/drivers/mtd/Makefile
-+++ b/drivers/mtd/Makefile
-@@ -8,6 +8,7 @@ mtd-y				:= mtdcore.o mtdsuper.o mtdbdi.
- mtd-$(CONFIG_MTD_PARTITIONS)	+= mtdpart.o
- 
- obj-$(CONFIG_MTD_CONCAT)	+= mtdconcat.o
-+obj-$(CONFIG_MTD_TRXSPLIT)	+= trxsplit.o
- obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
- obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
- obj-$(CONFIG_MTD_AFS_PARTS)	+= afs.o
diff --git a/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch b/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch
deleted file mode 100644
index 3d9bbdd..0000000
--- a/target/linux/adm5120/patches-2.6.30/120-rb153_cf_driver.patch
+++ /dev/null
@@ -1,28 +0,0 @@
---- a/drivers/ata/Makefile
-+++ b/drivers/ata/Makefile
-@@ -73,6 +73,7 @@ obj-$(CONFIG_PATA_OCTEON_CF)	+= pata_oct
- obj-$(CONFIG_PATA_PLATFORM)	+= pata_platform.o
- obj-$(CONFIG_PATA_OF_PLATFORM)	+= pata_of_platform.o
- obj-$(CONFIG_PATA_ICSIDE)	+= pata_icside.o
-+obj-$(CONFIG_PATA_RB153_CF)	+= pata_rb153_cf.o
- # Should be last but two libata driver
- obj-$(CONFIG_PATA_ACPI)		+= pata_acpi.o
- # Should be last but one libata driver
---- a/drivers/ata/Kconfig
-+++ b/drivers/ata/Kconfig
-@@ -568,6 +568,15 @@ config PATA_RADISYS
- 
- 	  If unsure, say N.
- 
-+config PATA_RB153_CF
-+	tristate "RouterBOARD 153 Compact Flash support"
-+	depends on ADM5120_MACH_RB_153
-+	help
-+	  This option enables support for a Compact Flash connected on
-+	  the RouterBOARD 153.
-+
-+	  If unsure, say N.
-+
- config PATA_RB532
- 	tristate "RouterBoard 532 PATA CompactFlash support"
- 	depends on MIKROTIK_RB532
diff --git a/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch b/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch
deleted file mode 100644
index 2857644..0000000
--- a/target/linux/adm5120/patches-2.6.30/200-amba_pl010_hacks.patch
+++ /dev/null
@@ -1,378 +0,0 @@
---- a/drivers/serial/amba-pl010.c
-+++ b/drivers/serial/amba-pl010.c
-@@ -50,11 +50,10 @@
- 
- #include <asm/io.h>
- 
--#define UART_NR		8
--
- #define SERIAL_AMBA_MAJOR	204
- #define SERIAL_AMBA_MINOR	16
--#define SERIAL_AMBA_NR		UART_NR
-+#define SERIAL_AMBA_NR		CONFIG_SERIAL_AMBA_PL010_NUMPORTS
-+#define SERIAL_AMBA_NAME	CONFIG_SERIAL_AMBA_PL010_PORTNAME
- 
- #define AMBA_ISR_PASS_LIMIT	256
- 
-@@ -80,9 +79,9 @@ static void pl010_stop_tx(struct uart_po
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr &= ~UART010_CR_TIE;
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_start_tx(struct uart_port *port)
-@@ -90,9 +89,9 @@ static void pl010_start_tx(struct uart_p
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr |= UART010_CR_TIE;
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_stop_rx(struct uart_port *port)
-@@ -100,9 +99,9 @@ static void pl010_stop_rx(struct uart_po
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_enable_ms(struct uart_port *port)
-@@ -110,9 +109,9 @@ static void pl010_enable_ms(struct uart_
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
- 	unsigned int cr;
- 
--	cr = readb(uap->port.membase + UART010_CR);
-+	cr = __raw_readl(uap->port.membase + UART010_CR);
- 	cr |= UART010_CR_MSIE;
--	writel(cr, uap->port.membase + UART010_CR);
-+	__raw_writel(cr, uap->port.membase + UART010_CR);
- }
- 
- static void pl010_rx_chars(struct uart_amba_port *uap)
-@@ -120,9 +119,9 @@ static void pl010_rx_chars(struct uart_a
- 	struct tty_struct *tty = uap->port.info->port.tty;
- 	unsigned int status, ch, flag, rsr, max_count = 256;
- 
--	status = readb(uap->port.membase + UART01x_FR);
-+	status = __raw_readl(uap->port.membase + UART01x_FR);
- 	while (UART_RX_DATA(status) && max_count--) {
--		ch = readb(uap->port.membase + UART01x_DR);
-+		ch = __raw_readl(uap->port.membase + UART01x_DR);
- 		flag = TTY_NORMAL;
- 
- 		uap->port.icount.rx++;
-@@ -131,9 +130,9 @@ static void pl010_rx_chars(struct uart_a
- 		 * Note that the error handling code is
- 		 * out of the main execution path
- 		 */
--		rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
-+		rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
- 		if (unlikely(rsr & UART01x_RSR_ANY)) {
--			writel(0, uap->port.membase + UART01x_ECR);
-+			__raw_writel(0, uap->port.membase + UART01x_ECR);
- 
- 			if (rsr & UART01x_RSR_BE) {
- 				rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
-@@ -163,7 +162,7 @@ static void pl010_rx_chars(struct uart_a
- 		uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
- 
- 	ignore_char:
--		status = readb(uap->port.membase + UART01x_FR);
-+		status = __raw_readl(uap->port.membase + UART01x_FR);
- 	}
- 	spin_unlock(&uap->port.lock);
- 	tty_flip_buffer_push(tty);
-@@ -176,7 +175,7 @@ static void pl010_tx_chars(struct uart_a
- 	int count;
- 
- 	if (uap->port.x_char) {
--		writel(uap->port.x_char, uap->port.membase + UART01x_DR);
-+		__raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR);
- 		uap->port.icount.tx++;
- 		uap->port.x_char = 0;
- 		return;
-@@ -188,7 +187,7 @@ static void pl010_tx_chars(struct uart_a
- 
- 	count = uap->port.fifosize >> 1;
- 	do {
--		writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
-+		__raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
- 		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- 		uap->port.icount.tx++;
- 		if (uart_circ_empty(xmit))
-@@ -206,9 +205,9 @@ static void pl010_modem_status(struct ua
- {
- 	unsigned int status, delta;
- 
--	writel(0, uap->port.membase + UART010_ICR);
-+	__raw_writel(0, uap->port.membase + UART010_ICR);
- 
--	status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+	status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
- 
- 	delta = status ^ uap->old_status;
- 	uap->old_status = status;
-@@ -236,7 +235,7 @@ static irqreturn_t pl010_int(int irq, vo
- 
- 	spin_lock(&uap->port.lock);
- 
--	status = readb(uap->port.membase + UART010_IIR);
-+	status = __raw_readl(uap->port.membase + UART010_IIR);
- 	if (status) {
- 		do {
- 			if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
-@@ -249,7 +248,7 @@ static irqreturn_t pl010_int(int irq, vo
- 			if (pass_counter-- == 0)
- 				break;
- 
--			status = readb(uap->port.membase + UART010_IIR);
-+			status = __raw_readl(uap->port.membase + UART010_IIR);
- 		} while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
- 				   UART010_IIR_TIS));
- 		handled = 1;
-@@ -263,7 +262,7 @@ static irqreturn_t pl010_int(int irq, vo
- static unsigned int pl010_tx_empty(struct uart_port *port)
- {
- 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
--	unsigned int status = readb(uap->port.membase + UART01x_FR);
-+	unsigned int status = __raw_readl(uap->port.membase + UART01x_FR);
- 	return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
- }
- 
-@@ -273,7 +272,7 @@ static unsigned int pl010_get_mctrl(stru
- 	unsigned int result = 0;
- 	unsigned int status;
- 
--	status = readb(uap->port.membase + UART01x_FR);
-+	status = __raw_readl(uap->port.membase + UART01x_FR);
- 	if (status & UART01x_FR_DCD)
- 		result |= TIOCM_CAR;
- 	if (status & UART01x_FR_DSR)
-@@ -299,12 +298,12 @@ static void pl010_break_ctl(struct uart_
- 	unsigned int lcr_h;
- 
- 	spin_lock_irqsave(&uap->port.lock, flags);
--	lcr_h = readb(uap->port.membase + UART010_LCRH);
-+	lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
- 	if (break_state == -1)
- 		lcr_h |= UART01x_LCRH_BRK;
- 	else
- 		lcr_h &= ~UART01x_LCRH_BRK;
--	writel(lcr_h, uap->port.membase + UART010_LCRH);
-+	__raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
- 	spin_unlock_irqrestore(&uap->port.lock, flags);
- }
- 
-@@ -332,12 +331,12 @@ static int pl010_startup(struct uart_por
- 	/*
- 	 * initialise the old status of the modem signals
- 	 */
--	uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+	uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
- 
- 	/*
- 	 * Finally, enable interrupts
- 	 */
--	writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
-+	__raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
- 	       uap->port.membase + UART010_CR);
- 
- 	return 0;
-@@ -360,10 +359,10 @@ static void pl010_shutdown(struct uart_p
- 	/*
- 	 * disable all interrupts, disable the port
- 	 */
--	writel(0, uap->port.membase + UART010_CR);
-+	__raw_writel(0, uap->port.membase + UART010_CR);
- 
- 	/* disable break condition and fifos */
--	writel(readb(uap->port.membase + UART010_LCRH) &
-+	__raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) &
- 		~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
- 	       uap->port.membase + UART010_LCRH);
- 
-@@ -385,7 +384,7 @@ pl010_set_termios(struct uart_port *port
- 	/*
- 	 * Ask the core to calculate the divisor for us.
- 	 */
--	baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); 
-+	baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
- 	quot = uart_get_divisor(port, baud);
- 
- 	switch (termios->c_cflag & CSIZE) {
-@@ -448,25 +447,25 @@ pl010_set_termios(struct uart_port *port
- 		uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
- 
- 	/* first, disable everything */
--	old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
-+	old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
- 
- 	if (UART_ENABLE_MS(port, termios->c_cflag))
- 		old_cr |= UART010_CR_MSIE;
- 
--	writel(0, uap->port.membase + UART010_CR);
-+	__raw_writel(0, uap->port.membase + UART010_CR);
- 
- 	/* Set baud rate */
- 	quot -= 1;
--	writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
--	writel(quot & 0xff, uap->port.membase + UART010_LCRL);
-+	__raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
-+	__raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL);
- 
- 	/*
- 	 * ----------v----------v----------v----------v-----
- 	 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
- 	 * ----------^----------^----------^----------^-----
- 	 */
--	writel(lcr_h, uap->port.membase + UART010_LCRH);
--	writel(old_cr, uap->port.membase + UART010_CR);
-+	__raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
-+	__raw_writel(old_cr, uap->port.membase + UART010_CR);
- 
- 	spin_unlock_irqrestore(&uap->port.lock, flags);
- }
-@@ -538,7 +537,7 @@ static struct uart_ops amba_pl010_pops =
- 	.verify_port	= pl010_verify_port,
- };
- 
--static struct uart_amba_port *amba_ports[UART_NR];
-+static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
- 
- #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
- 
-@@ -548,10 +547,10 @@ static void pl010_console_putchar(struct
- 	unsigned int status;
- 
- 	do {
--		status = readb(uap->port.membase + UART01x_FR);
-+		status = __raw_readl(uap->port.membase + UART01x_FR);
- 		barrier();
- 	} while (!UART_TX_READY(status));
--	writel(ch, uap->port.membase + UART01x_DR);
-+	__raw_writel(ch, uap->port.membase + UART01x_DR);
- }
- 
- static void
-@@ -565,8 +564,8 @@ pl010_console_write(struct console *co, 
- 	/*
- 	 *	First save the CR then disable the interrupts
- 	 */
--	old_cr = readb(uap->port.membase + UART010_CR);
--	writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
-+	old_cr = __raw_readl(uap->port.membase + UART010_CR);
-+	__raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
- 
- 	uart_console_write(&uap->port, s, count, pl010_console_putchar);
- 
-@@ -575,10 +574,10 @@ pl010_console_write(struct console *co, 
- 	 *	and restore the TCR
- 	 */
- 	do {
--		status = readb(uap->port.membase + UART01x_FR);
-+		status = __raw_readl(uap->port.membase + UART01x_FR);
- 		barrier();
- 	} while (status & UART01x_FR_BUSY);
--	writel(old_cr, uap->port.membase + UART010_CR);
-+	__raw_writel(old_cr, uap->port.membase + UART010_CR);
- 
- 	clk_disable(uap->clk);
- }
-@@ -587,9 +586,9 @@ static void __init
- pl010_console_get_options(struct uart_amba_port *uap, int *baud,
- 			     int *parity, int *bits)
- {
--	if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
-+	if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
- 		unsigned int lcr_h, quot;
--		lcr_h = readb(uap->port.membase + UART010_LCRH);
-+		lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
- 
- 		*parity = 'n';
- 		if (lcr_h & UART01x_LCRH_PEN) {
-@@ -604,8 +603,8 @@ pl010_console_get_options(struct uart_am
- 		else
- 			*bits = 8;
- 
--		quot = readb(uap->port.membase + UART010_LCRL) |
--		       readb(uap->port.membase + UART010_LCRM) << 8;
-+		quot = __raw_readl(uap->port.membase + UART010_LCRL) |
-+		       __raw_readl(uap->port.membase + UART010_LCRM) << 8;
- 		*baud = uap->port.uartclk / (16 * (quot + 1));
- 	}
- }
-@@ -623,7 +622,7 @@ static int __init pl010_console_setup(st
- 	 * if so, search for the first available port that does have
- 	 * console support.
- 	 */
--	if (co->index >= UART_NR)
-+	if (co->index >= SERIAL_AMBA_NR)
- 		co->index = 0;
- 	uap = amba_ports[co->index];
- 	if (!uap)
-@@ -641,7 +640,7 @@ static int __init pl010_console_setup(st
- 
- static struct uart_driver amba_reg;
- static struct console amba_console = {
--	.name		= "ttyAM",
-+	.name		= SERIAL_AMBA_NAME,
- 	.write		= pl010_console_write,
- 	.device		= uart_console_device,
- 	.setup		= pl010_console_setup,
-@@ -657,11 +656,11 @@ static struct console amba_console = {
- 
- static struct uart_driver amba_reg = {
- 	.owner			= THIS_MODULE,
--	.driver_name		= "ttyAM",
--	.dev_name		= "ttyAM",
-+	.driver_name		= SERIAL_AMBA_NAME,
-+	.dev_name		= SERIAL_AMBA_NAME,
- 	.major			= SERIAL_AMBA_MAJOR,
- 	.minor			= SERIAL_AMBA_MINOR,
--	.nr			= UART_NR,
-+	.nr			= SERIAL_AMBA_NR,
- 	.cons			= AMBA_CONSOLE,
- };
- 
---- a/drivers/serial/Kconfig
-+++ b/drivers/serial/Kconfig
-@@ -284,10 +284,25 @@ config SERIAL_AMBA_PL010
- 	help
- 	  This selects the ARM(R) AMBA(R) PrimeCell PL010 UART.  If you have
- 	  an Integrator/AP or Integrator/PP2 platform, or if you have a
--	  Cirrus Logic EP93xx CPU, say Y or M here.
-+	  Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
- 
- 	  If unsure, say N.
- 
-+config SERIAL_AMBA_PL010_NUMPORTS
-+	int "Maximum number of AMBA PL010 serial ports"
-+	depends on SERIAL_AMBA_PL010
-+	default "8"
-+	---help---
-+	  Set this to the number of serial ports you want the AMBA PL010 driver
-+	  to support.
-+
-+config SERIAL_AMBA_PL010_PORTNAME
-+	string "Name of the AMBA PL010 serial ports"
-+	depends on SERIAL_AMBA_PL010
-+	default "ttyAM"
-+	---help---
-+	  ::: To be written :::
-+
- config SERIAL_AMBA_PL010_CONSOLE
- 	bool "Support for console on AMBA serial port"
- 	depends on SERIAL_AMBA_PL010=y
diff --git a/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch b/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch
deleted file mode 100644
index 9db3e55..0000000
--- a/target/linux/adm5120/patches-2.6.30/201-amba_bus_hacks.patch
+++ /dev/null
@@ -1,13 +0,0 @@
---- a/drivers/amba/bus.c
-+++ b/drivers/amba/bus.c
-@@ -18,6 +18,10 @@
- #include <asm/irq.h>
- #include <asm/sizes.h>
- 
-+#ifndef NO_IRQ
-+#define NO_IRQ		(-1)
-+#endif
-+
- #define to_amba_device(d)	container_of(d, struct amba_device, dev)
- #define to_amba_driver(d)	container_of(d, struct amba_driver, drv)
- 
diff --git a/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch b/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch
deleted file mode 100644
index 8bccf39..0000000
--- a/target/linux/adm5120/patches-2.6.30/203-gpio_leds_brightness.patch
+++ /dev/null
@@ -1,27 +0,0 @@
---- a/drivers/leds/leds-gpio.c
-+++ b/drivers/leds/leds-gpio.c
-@@ -44,13 +44,17 @@ static void gpio_led_set(struct led_clas
- 		container_of(led_cdev, struct gpio_led_data, cdev);
- 	int level;
- 
--	if (value == LED_OFF)
--		level = 0;
--	else
--		level = 1;
--
--	if (led_dat->active_low)
--		level = !level;
-+	switch (value) {
-+	case LED_OFF:
-+		level = led_dat->active_low ? 1 : 0;
-+		break;
-+	case LED_FULL:
-+		level = led_dat->active_low ? 0 : 1;
-+		break;
-+	default:
-+		level = value;
-+		break;
-+	}
- 
- 	/* Setting GPIOs with I2C/etc requires a task context, and we don't
- 	 * seem to have a reliable way to know if we're already in one; so
diff --git a/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch b/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch
deleted file mode 100644
index bb5e613..0000000
--- a/target/linux/adm5120/patches-2.6.30/310-adm5120_wdt.patch
+++ /dev/null
@@ -1,31 +0,0 @@
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -713,6 +713,18 @@ config RC32434_WDT
- 	  To compile this driver as a module, choose M here: the
- 	  module will be called rc32434_wdt.
- 
-+config ADM5120_WDT
-+	tristate "Infineon ADM5120 SoC hardware watchdog"
-+	depends on WATCHDOG && ADM5120
-+	help
-+	  This is a driver for hardware watchdog integrated in Infineon
-+	  ADM5120 SoC. This watchdog simply watches your kernel to make sure
-+	  it doesn't freeze, and if it does, it reboots your computer after a
-+	  certain amount of time.
-+
-+	  To compile this driver as a module, choose M here: the module will be
-+	  called adm5120_wdt.
-+
- config INDYDOG
- 	tristate "Indy/I2 Hardware Watchdog"
- 	depends on SGI_HAS_INDYDOG
---- a/drivers/watchdog/Makefile
-+++ b/drivers/watchdog/Makefile
-@@ -105,6 +105,7 @@ obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
- obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
- obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
- obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
-+obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o
- 
- # PARISC Architecture
- 
diff --git a/target/linux/adm5120/router_be/config-2.6.30 b/target/linux/adm5120/router_be/config-2.6.30
deleted file mode 100644
index cde882d..0000000
--- a/target/linux/adm5120/router_be/config-2.6.30
+++ /dev/null
@@ -1,205 +0,0 @@
-CONFIG_32BIT=y
-# CONFIG_64BIT is not set
-CONFIG_ADM5120=y
-CONFIG_ADM5120_ENET=y
-CONFIG_ADM5120_MACH_5GXI=y
-CONFIG_ADM5120_MACH_P_334WT=y
-CONFIG_ADM5120_MACH_P_335=y
-# CONFIG_ADM5120_OEM_CELLVISION is not set
-# CONFIG_ADM5120_OEM_COMPEX is not set
-# CONFIG_ADM5120_OEM_EDIMAX is not set
-# CONFIG_ADM5120_OEM_INFINEON is not set
-# CONFIG_ADM5120_OEM_MIKROTIK is not set
-# CONFIG_ADM5120_OEM_MOTOROLA is not set
-CONFIG_ADM5120_OEM_OSBRIDGE=y
-CONFIG_ADM5120_OEM_ZYXEL=y
-CONFIG_ADM5120_SOC_BGA=y
-CONFIG_ADM5120_WDT=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_ARCH_POPULATES_NODE_MAP=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_ARCH_SUPPORTS_OPROFILE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARM_AMBA=y
-# CONFIG_BCM47XX is not set
-# CONFIG_BINARY_PRINTF is not set
-CONFIG_BINFMT_MISC=m
-CONFIG_BITREVERSE=y
-# CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set
-# CONFIG_CAVIUM_OCTEON_SIMULATOR is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CEVT_R4K=y
-CONFIG_CEVT_R4K_LIB=y
-CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2"
-CONFIG_CPU_BIG_ENDIAN=y
-# CONFIG_CPU_CAVIUM_OCTEON is not set
-CONFIG_CPU_HAS_LLSC=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-# CONFIG_CPU_LITTLE_ENDIAN is not set
-# CONFIG_CPU_LOONGSON2 is not set
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPS32_R1=y
-# CONFIG_CPU_MIPS32_R2 is not set
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-CONFIG_CPU_MIPSR1=y
-# CONFIG_CPU_NEVADA is not set
-# CONFIG_CPU_R10000 is not set
-# CONFIG_CPU_R3000 is not set
-# CONFIG_CPU_R4300 is not set
-# CONFIG_CPU_R4X00 is not set
-# CONFIG_CPU_R5000 is not set
-# CONFIG_CPU_R5432 is not set
-# CONFIG_CPU_R5500 is not set
-# CONFIG_CPU_R6000 is not set
-# CONFIG_CPU_R8000 is not set
-# CONFIG_CPU_RM7000 is not set
-# CONFIG_CPU_RM9000 is not set
-# CONFIG_CPU_SB1 is not set
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-# CONFIG_CPU_TX39XX is not set
-# CONFIG_CPU_TX49XX is not set
-# CONFIG_CPU_VR41XX is not set
-CONFIG_CSRC_R4K=y
-CONFIG_CSRC_R4K_LIB=y
-CONFIG_DECOMPRESS_LZMA=y
-CONFIG_DEVPORT=y
-# CONFIG_DM9000 is not set
-CONFIG_DMA_NEED_PCI_MAP_STATE=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_ELF_CORE=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_FS_POSIX_ACL=y
-CONFIG_GENERIC_ACL=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_FIND_LAST_BIT=y
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_ARCH_KGDB=y
-# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_MLOCK=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HID=m
-CONFIG_HID_SUPPORT=y
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ=250
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-CONFIG_INPUT=m
-# CONFIG_INPUT_GPIO_BUTTONS is not set
-# CONFIG_INPUT_YEALINK is not set
-CONFIG_IRQ_CPU=y
-CONFIG_LEDS_GPIO=m
-CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-# CONFIG_LEMOTE_FULONG is not set
-# CONFIG_MACH_ALCHEMY is not set
-# CONFIG_MACH_DECSTATION is not set
-# CONFIG_MACH_JAZZ is not set
-# CONFIG_MACH_TX39XX is not set
-# CONFIG_MACH_TX49XX is not set
-# CONFIG_MACH_VR41XX is not set
-CONFIG_MII=m
-# CONFIG_MIKROTIK_RB532 is not set
-CONFIG_MIPS=y
-# CONFIG_MIPS_COBALT is not set
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-CONFIG_MIPS_MACHINE=y
-# CONFIG_MIPS_MALTA is not set
-CONFIG_MIPS_MT_DISABLED=y
-# CONFIG_MIPS_MT_SMP is not set
-# CONFIG_MIPS_MT_SMTC is not set
-# CONFIG_MIPS_SIM is not set
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_ADM5120=y
-CONFIG_MTD_BLOCK2MTD=y
-CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
-# CONFIG_MTD_CFI_INTELEXT is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_TRXSPLIT=y
-# CONFIG_NET_PCI is not set
-# CONFIG_NO_IOPORT is not set
-# CONFIG_NXP_STB220 is not set
-# CONFIG_NXP_STB225 is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_PCI=y
-CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
-CONFIG_PCI_DOMAINS=y
-# CONFIG_PMC_MSP is not set
-# CONFIG_PMC_YOSEMITE is not set
-# CONFIG_PNX8550_JBS is not set
-# CONFIG_PNX8550_STB810 is not set
-# CONFIG_PROBE_INITRD_HEADER is not set
-CONFIG_SCHED_OMIT_FRAME_POINTER=y
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
-CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
-CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SERIO=y
-# CONFIG_SERIO_AMBAKMI is not set
-# CONFIG_SERIO_I8042 is not set
-# CONFIG_SERIO_LIBPS2 is not set
-# CONFIG_SERIO_PCIPS2 is not set
-# CONFIG_SERIO_RAW is not set
-CONFIG_SERIO_SERPORT=y
-# CONFIG_SGI_IP22 is not set
-# CONFIG_SGI_IP27 is not set
-# CONFIG_SGI_IP28 is not set
-# CONFIG_SGI_IP32 is not set
-# CONFIG_SIBYTE_BIGSUR is not set
-# CONFIG_SIBYTE_CARMEL is not set
-# CONFIG_SIBYTE_CRHINE is not set
-# CONFIG_SIBYTE_CRHONE is not set
-# CONFIG_SIBYTE_LITTLESUR is not set
-# CONFIG_SIBYTE_RHONE is not set
-# CONFIG_SIBYTE_SENTOSA is not set
-# CONFIG_SIBYTE_SWARM is not set
-# CONFIG_SLAB is not set
-# CONFIG_SLOW_WORK is not set
-CONFIG_SLUB=y
-CONFIG_SOFT_WATCHDOG=m
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_TRACING_SUPPORT=y
-CONFIG_TRAD_SIGNALS=y
-CONFIG_USB=m
-CONFIG_USB_ADM5120_HCD=m
-CONFIG_USB_DEBUG=y
-CONFIG_USB_EHCI_HCD=m
-# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
-CONFIG_USB_OHCI_HCD=m
-CONFIG_USB_SUPPORT=y
-# CONFIG_USB_UHCI_HCD is not set
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/adm5120/router_le/config-2.6.30 b/target/linux/adm5120/router_le/config-2.6.30
deleted file mode 100644
index ead803f..0000000
--- a/target/linux/adm5120/router_le/config-2.6.30
+++ /dev/null
@@ -1,260 +0,0 @@
-CONFIG_32BIT=y
-# CONFIG_64BIT is not set
-CONFIG_ADM5120=y
-CONFIG_ADM5120_ENET=y
-CONFIG_ADM5120_MACH_5GXI=y
-CONFIG_ADM5120_MACH_BR_6104K=y
-CONFIG_ADM5120_MACH_BR_6104KP=y
-CONFIG_ADM5120_MACH_BR_61X4WG=y
-CONFIG_ADM5120_MACH_CAS_771=y
-CONFIG_ADM5120_MACH_EASY5120P_ATA=y
-CONFIG_ADM5120_MACH_EASY5120_RT=y
-CONFIG_ADM5120_MACH_EASY5120_WVOIP=y
-CONFIG_ADM5120_MACH_EASY83000=y
-CONFIG_ADM5120_MACH_NFS_101=y
-CONFIG_ADM5120_MACH_NP27G=y
-CONFIG_ADM5120_MACH_NP28G=y
-CONFIG_ADM5120_MACH_PMUGW=y
-CONFIG_ADM5120_MACH_RB_11X=y
-CONFIG_ADM5120_MACH_RB_133=y
-CONFIG_ADM5120_MACH_RB_133C=y
-CONFIG_ADM5120_MACH_RB_150=y
-CONFIG_ADM5120_MACH_RB_153=y
-CONFIG_ADM5120_MACH_RB_192=y
-CONFIG_ADM5120_MACH_WP54=y
-CONFIG_ADM5120_OEM_CELLVISION=y
-CONFIG_ADM5120_OEM_COMPEX=y
-CONFIG_ADM5120_OEM_EDIMAX=y
-CONFIG_ADM5120_OEM_INFINEON=y
-CONFIG_ADM5120_OEM_MIKROTIK=y
-CONFIG_ADM5120_OEM_MOTOROLA=y
-CONFIG_ADM5120_OEM_OSBRIDGE=y
-# CONFIG_ADM5120_OEM_ZYXEL is not set
-CONFIG_ADM5120_SOC_BGA=y
-CONFIG_ADM5120_WDT=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_ARCH_POPULATES_NODE_MAP=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_ARCH_SUPPORTS_OPROFILE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARM_AMBA=y
-CONFIG_ATA=m
-# CONFIG_BCM47XX is not set
-# CONFIG_BINARY_PRINTF is not set
-CONFIG_BITREVERSE=y
-# CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set
-# CONFIG_CAVIUM_OCTEON_SIMULATOR is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CEVT_R4K=y
-CONFIG_CEVT_R4K_LIB=y
-CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2"
-# CONFIG_CPU_BIG_ENDIAN is not set
-# CONFIG_CPU_CAVIUM_OCTEON is not set
-CONFIG_CPU_HAS_LLSC=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-# CONFIG_CPU_LOONGSON2 is not set
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPS32_R1=y
-# CONFIG_CPU_MIPS32_R2 is not set
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-CONFIG_CPU_MIPSR1=y
-# CONFIG_CPU_NEVADA is not set
-# CONFIG_CPU_R10000 is not set
-# CONFIG_CPU_R3000 is not set
-# CONFIG_CPU_R4300 is not set
-# CONFIG_CPU_R4X00 is not set
-# CONFIG_CPU_R5000 is not set
-# CONFIG_CPU_R5432 is not set
-# CONFIG_CPU_R5500 is not set
-# CONFIG_CPU_R6000 is not set
-# CONFIG_CPU_R8000 is not set
-# CONFIG_CPU_RM7000 is not set
-# CONFIG_CPU_RM9000 is not set
-# CONFIG_CPU_SB1 is not set
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-# CONFIG_CPU_TX39XX is not set
-# CONFIG_CPU_TX49XX is not set
-# CONFIG_CPU_VR41XX is not set
-CONFIG_CRYPTO_AEAD2=y
-CONFIG_CRYPTO_AES=m
-CONFIG_CRYPTO_ARC4=m
-CONFIG_CRYPTO_BLKCIPHER=m
-CONFIG_CRYPTO_BLKCIPHER2=y
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_HASH=m
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_MANAGER=m
-CONFIG_CRYPTO_MANAGER2=y
-CONFIG_CRYPTO_MICHAEL_MIC=m
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_CSRC_R4K=y
-CONFIG_CSRC_R4K_LIB=y
-CONFIG_DECOMPRESS_LZMA=y
-CONFIG_DEVPORT=y
-# CONFIG_DM9000 is not set
-CONFIG_DMA_NEED_PCI_MAP_STATE=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_ELF_CORE=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_FS_POSIX_ACL=y
-CONFIG_GENERIC_ACL=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_FIND_LAST_BIT=y
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_SYSFS=y
-# CONFIG_HAMRADIO is not set
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_ARCH_KGDB=y
-# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_MLOCK=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HID=m
-CONFIG_HID_SUPPORT=y
-CONFIG_HOSTAP=m
-CONFIG_HOSTAP_FIRMWARE=y
-# CONFIG_HOSTAP_FIRMWARE_NVRAM is not set
-CONFIG_HOSTAP_PCI=m
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ=250
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-CONFIG_IMAGE_CMDLINE_HACK=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-CONFIG_INPUT=m
-# CONFIG_INPUT_GPIO_BUTTONS is not set
-# CONFIG_INPUT_YEALINK is not set
-CONFIG_IRQ_CPU=y
-CONFIG_KEXEC=y
-CONFIG_LEDS_GPIO=m
-CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-# CONFIG_LEMOTE_FULONG is not set
-CONFIG_LIB80211=m
-CONFIG_LIB80211_CRYPT_CCMP=m
-CONFIG_LIB80211_CRYPT_TKIP=m
-CONFIG_LIB80211_CRYPT_WEP=m
-# CONFIG_MACH_ALCHEMY is not set
-# CONFIG_MACH_DECSTATION is not set
-# CONFIG_MACH_JAZZ is not set
-# CONFIG_MACH_TX39XX is not set
-# CONFIG_MACH_TX49XX is not set
-# CONFIG_MACH_VR41XX is not set
-CONFIG_MII=m
-# CONFIG_MIKROTIK_RB532 is not set
-CONFIG_MIPS=y
-# CONFIG_MIPS_COBALT is not set
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-CONFIG_MIPS_MACHINE=y
-# CONFIG_MIPS_MALTA is not set
-CONFIG_MIPS_MT_DISABLED=y
-# CONFIG_MIPS_MT_SMP is not set
-# CONFIG_MIPS_MT_SMTC is not set
-# CONFIG_MIPS_SIM is not set
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_ADM5120=y
-CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
-# CONFIG_MTD_CFI_INTELEXT is not set
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_MYLOADER_PARTS=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_PLATFORM=y
-CONFIG_MTD_TRXSPLIT=y
-CONFIG_NO_HZ=y
-# CONFIG_NO_IOPORT is not set
-# CONFIG_NXP_STB220 is not set
-# CONFIG_NXP_STB225 is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_PCI=y 
-CONFIG_PATA_RB153_CF=m
-CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
-CONFIG_PCI_DOMAINS=y
-# CONFIG_PMC_MSP is not set
-# CONFIG_PMC_YOSEMITE is not set
-# CONFIG_PNX8550_JBS is not set
-# CONFIG_PNX8550_STB810 is not set
-# CONFIG_PROBE_INITRD_HEADER is not set
-CONFIG_SCHED_OMIT_FRAME_POINTER=y
-CONFIG_SCSI=m
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
-CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
-CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SERIO=y
-# CONFIG_SERIO_AMBAKMI is not set
-# CONFIG_SERIO_I8042 is not set
-# CONFIG_SERIO_LIBPS2 is not set
-# CONFIG_SERIO_PCIPS2 is not set
-# CONFIG_SERIO_RAW is not set
-CONFIG_SERIO_SERPORT=y
-# CONFIG_SGI_IP22 is not set
-# CONFIG_SGI_IP27 is not set
-# CONFIG_SGI_IP28 is not set
-# CONFIG_SGI_IP32 is not set
-# CONFIG_SIBYTE_BIGSUR is not set
-# CONFIG_SIBYTE_CARMEL is not set
-# CONFIG_SIBYTE_CRHINE is not set
-# CONFIG_SIBYTE_CRHONE is not set
-# CONFIG_SIBYTE_LITTLESUR is not set
-# CONFIG_SIBYTE_RHONE is not set
-# CONFIG_SIBYTE_SENTOSA is not set
-# CONFIG_SIBYTE_SWARM is not set
-# CONFIG_SLAB is not set
-# CONFIG_SLOW_WORK is not set
-CONFIG_SLUB=y
-CONFIG_SOFT_WATCHDOG=m
-# CONFIG_SWAP is not set
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
-# CONFIG_TC35815 is not set
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_TRACING_SUPPORT=y
-CONFIG_TRAD_SIGNALS=y
-CONFIG_USB=m
-CONFIG_USB_ADM5120_HCD=m
-CONFIG_USB_EHCI_HCD=m
-# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
-CONFIG_USB_OHCI_HCD=m
-CONFIG_USB_SUPPORT=y
-# CONFIG_USB_UHCI_HCD is not set
-CONFIG_VLAN_8021Q=m
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_YAFFS_9BYTE_TAGS=y
-# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set
-CONFIG_YAFFS_AUTO_YAFFS2=y
-# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set
-# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
-CONFIG_YAFFS_FS=y
-CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
-CONFIG_YAFFS_YAFFS1=y
-CONFIG_YAFFS_YAFFS2=y
-CONFIG_ZONE_DMA_FLAG=0