summaryrefslogtreecommitdiff
path: root/target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch
diff options
context:
space:
mode:
authorJonas Gorski <jogo@openwrt.org>2013-01-04 14:47:43 +0000
committerJonas Gorski <jogo@openwrt.org>2013-01-04 14:47:43 +0000
commit10fc07daacfee223f869397d356d1481e4094e12 (patch)
tree6a82d3ed0768bbed69af8bdce78fa4434bb3cf72 /target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch
parent3b7882e7752f154ce6407c892e7b92015c5c3481 (diff)
downloadmtk-20170518-10fc07daacfee223f869397d356d1481e4094e12.zip
mtk-20170518-10fc07daacfee223f869397d356d1481e4094e12.tar.gz
mtk-20170518-10fc07daacfee223f869397d356d1481e4094e12.tar.bz2
bcm63xx: remove 3.3 support
3.6 is tested enough to be considered stable. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 35009
Diffstat (limited to 'target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch')
-rw-r--r--target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch122
1 files changed, 0 insertions, 122 deletions
diff --git a/target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch b/target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch
deleted file mode 100644
index 86b7fe1..0000000
--- a/target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch
+++ /dev/null
@@ -1,122 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -832,6 +832,63 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_V2500V_BB = {
-+ .name = "V2500V_BB",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+ .enet1 = {
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "V2500V_BB:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "V2500V_BB:red:power",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "V2500V_BB:green:adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ { .name = "V2500V_BB:green:ppp",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "V2500V_BB:green:wireless",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 31,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -1873,6 +1930,7 @@ static const struct board_info __initdat
- &board_96348_D4PW,
- &board_spw500v,
- &board_96348sv,
-+ &board_V2500V_BB,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -1993,6 +2051,23 @@ void __init board_prom_init(void)
- val &= MPI_CSBASE_BASE_MASK;
- }
- boot_addr = (u8 *)KSEG1ADDR(val);
-+ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+ /* Do an early check of CFE and then select bank 0 */
-+
-+ if (boot_addr == (u8 *)0xbf800000) {
-+ unsigned char board_name[16];
-+ u8 *tmp_boot_addr;
-+ tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+ memcpy(board_name, tmp_boot_addr + BCM963XX_NVRAM_OFFSET + offsetof(struct bcm963xx_nvram, name), sizeof(board_name));
-+ if (!strcmp(board_name, "V2500V_BB")) {
-+ printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+ boot_addr = (u8 *)0xbfc00000; // Bank 0
-+ }
-+ }
-
- /* dump cfe version */
- cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -19,6 +19,7 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/flash.h>
-
-+#include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_dev_hsspi.h>
-@@ -162,6 +163,13 @@ int __init bcm63xx_flash_register(int nu
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
-
-+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+ /* Loading from CFE always uses Bank 0 */
-+ if (!strcmp(board_get_name(), "V2500V_BB")) {
-+ pr_info("V2500V: Start in Bank 0\n");
-+ val = val + 0x400000; // Select Bank 0 start address
-+ }
-+
- mtd_resources[0].start = val;
- mtd_resources[0].end = 0x1FFFFFFF;
-