bcm63xx: remove 3.3 support

3.6 is tested enough to be considered stable.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 35009

1 files changed, 0 insertions, 122 deletions

diff --git a/target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch b/target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch
deleted file mode 100644
index 86b7fe1..0000000
--- a/target/linux/brcm63xx/patches-3.3/511-board_V2500V.patch
+++ /dev/null
@@ -1,122 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -832,6 +832,63 @@ static struct board_info __initdata boar
- 		},
- 	},
- };
-+
-+static struct board_info __initdata board_V2500V_BB = {
-+	.name				= "V2500V_BB",
-+        .expected_cpu_id                = 0x6348,
-+
-+        .has_uart0                      = 1,
-+        .has_enet0                      = 1,
-+        .has_enet1                      = 1,
-+        .has_pci                        = 1,
-+
-+        .enet0 = {
-+                .has_phy                = 1,
-+                .use_internal_phy       = 1,
-+        },
-+        .enet1 = {
-+                .force_speed_100        = 1,
-+                .force_duplex_full      = 1,
-+	},
-+
-+	.leds =	{
-+		{
-+			.name		= "V2500V_BB:green:power",
-+			.gpio		= 0,
-+			.active_low	= 1,
-+			.default_trigger = "default-on",
-+		},
-+		{
-+			.name		= "V2500V_BB:red:power",
-+			.gpio		= 1,
-+			.active_low	= 1,
-+		},
-+		{
-+			.name		= "V2500V_BB:green:adsl",
-+			.gpio		= 2,
-+			.active_low	= 1,
-+		},
-+		{	.name		= "V2500V_BB:green:ppp",
-+			.gpio		= 3,
-+			.active_low	= 1,
-+		},
-+		{
-+			.name		= "V2500V_BB:green:wireless",
-+			.gpio		= 6,
-+			.active_low	= 1,
-+		},
-+	},
-+	.buttons = {
-+		{
-+			.desc		= "reset",
-+			.gpio		= 31,
-+			.active_low	= 1,
-+			.type		= EV_KEY,
-+			.code		= KEY_RESTART,
-+			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+		},
-+	},
-+};
- #endif
- 
- /*
-@@ -1873,6 +1930,7 @@ static const struct board_info __initdat
- 	&board_96348_D4PW,
- 	&board_spw500v,
- 	&board_96348sv,
-+	&board_V2500V_BB,
- #endif
- 
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -1993,6 +2051,23 @@ void __init board_prom_init(void)
- 		val &= MPI_CSBASE_BASE_MASK;
- 	}
- 	boot_addr = (u8 *)KSEG1ADDR(val);
-+	printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+	/* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+	/* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+	/* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+	/* Do an early check of CFE and then select bank 0 */
-+
-+	if (boot_addr == (u8 *)0xbf800000) {
-+		unsigned char board_name[16];
-+		u8 *tmp_boot_addr;
-+		tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+		memcpy(board_name, tmp_boot_addr + BCM963XX_NVRAM_OFFSET + offsetof(struct bcm963xx_nvram, name), sizeof(board_name));
-+		if (!strcmp(board_name, "V2500V_BB")) {
-+	               	printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+			boot_addr = (u8 *)0xbfc00000; // Bank 0
-+		}
-+	}
- 
- 	/* dump cfe version */
- 	cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -19,6 +19,7 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/flash.h>
- 
-+#include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_dev_hsspi.h>
-@@ -162,6 +163,13 @@ int __init bcm63xx_flash_register(int nu
- 		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- 		val &= MPI_CSBASE_BASE_MASK;
- 
-+		/* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+		/* Loading from CFE always uses Bank 0 */
-+		if (!strcmp(board_get_name(), "V2500V_BB")) {
-+			pr_info("V2500V: Start in Bank 0\n");
-+			val = val + 0x400000; // Select Bank 0 start address
-+		}
-+
- 		mtd_resources[0].start = val;
- 		mtd_resources[0].end = 0x1FFFFFFF;
-