add support for 2.6.37, patches from KanjiMonster

SVN-Revision: 25629

30 files changed, 4186 insertions, 0 deletions

diff --git a/target/linux/brcm63xx/config-2.6.37 b/target/linux/brcm63xx/config-2.6.37
new file mode 100644
index 0000000..ab2fdb1
--- /dev/null
+++ b/target/linux/brcm63xx/config-2.6.37
@@ -0,0 +1,160 @@
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_AUDIT=y
+CONFIG_AUDIT_GENERIC=y
+# CONFIG_AUTO_IRQ_AFFINITY is not set
+CONFIG_BCM63XX=y
+CONFIG_BCM63XX_CPU_6338=y
+CONFIG_BCM63XX_CPU_6345=y
+CONFIG_BCM63XX_CPU_6348=y
+CONFIG_BCM63XX_CPU_6358=y
+CONFIG_BCM63XX_ENET=y
+CONFIG_BCM63XX_PHY=y
+CONFIG_BCM63XX_WDT=y
+CONFIG_BKL=y
+CONFIG_BOARD_BCM963XX=y
+# CONFIG_BOARD_LIVEBOX is not set
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_CEVT_R4K=y
+CONFIG_CEVT_R4K_LIB=y
+CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200"
+CONFIG_CMDLINE_BOOL=y
+# CONFIG_CMDLINE_OVERRIDE is not set
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+CONFIG_CPU_MIPSR1=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_CRAMFS=y
+CONFIG_CSRC_R4K=y
+CONFIG_CSRC_R4K_LIB=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_ELF_CORE=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_GENERIC_HARDIRQS_NO_DEPRECATED is not set
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+# CONFIG_GENERIC_PENDING_IRQ is not set
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_74X164=y
+CONFIG_GPIO_DEVICE=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HAMRADIO is not set
+# CONFIG_HARDIRQS_SW_RESEND is not set
+CONFIG_HARDWARE_WATCHPOINTS=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_GENERIC_HARDIRQS=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+# CONFIG_HAVE_SPARSE_IRQ is not set
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+CONFIG_IMAGE_CMDLINE_HACK=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INOTIFY_USER=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_IRQ_CPU=y
+# CONFIG_IRQ_PER_CPU is not set
+CONFIG_KEXEC=y
+CONFIG_LEDS_GPIO=y
+# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
+CONFIG_LOONGSON_UART_BASE=y
+CONFIG_MACH_NO_WESTBRIDGE=y
+CONFIG_MIPS=y
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MACHINE is not set
+CONFIG_MIPS_MT_DISABLED=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MTD_BCM963XX=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_BE_BYTE_SWAP=y
+# CONFIG_MTD_CFI_GEOMETRY is not set
+# CONFIG_MTD_CFI_NOSWAP is not set
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PHYLIB=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_QUOTACTL is not set
+CONFIG_RELAY=y
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_BCM63XX=y
+CONFIG_SERIAL_BCM63XX_CONSOLE=y
+CONFIG_SPI=y
+# CONFIG_SPI_BCM63XX is not set
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_MASTER=y
+CONFIG_SQUASHFS_EMBEDDED=y
+CONFIG_SSB=y
+CONFIG_SSB_B43_PCI_BRIDGE=y
+CONFIG_SSB_BLOCKIO=y
+# CONFIG_SSB_DRIVER_MIPS is not set
+CONFIG_SSB_DRIVER_PCICORE=y
+CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
+CONFIG_SSB_PCIHOST=y
+CONFIG_SSB_PCIHOST_POSSIBLE=y
+CONFIG_SSB_SPROM=y
+CONFIG_SWAP_IO_SPACE=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y
+CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
+CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
+CONFIG_USB_SUPPORT=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/brcm63xx/patches-2.6.37/007-usb-ohci-support.patch b/target/linux/brcm63xx/patches-2.6.37/007-usb-ohci-support.patch
new file mode 100644
index 0000000..a70b501
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/007-usb-ohci-support.patch
@@ -0,0 +1,125 @@
+The bcm63xx SOC has an integrated OHCI controller, this patch adds
+platform device registration and change board code to register ohci
+device when necessary.
+
+Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
+---
+ arch/mips/bcm63xx/Kconfig                          |    6 ++
+ arch/mips/bcm63xx/Makefile                         |    3 +-
+ arch/mips/bcm63xx/boards/board_bcm963xx.c          |    4 ++
+ arch/mips/bcm63xx/dev-usb-ohci.c                   |   49 ++++++++++++++++++++
+ .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h        |    6 ++
+ 5 files changed, 67 insertions(+), 1 deletions(-)
+ create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
+
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -16,10 +16,16 @@ config BCM63XX_CPU_6345
+ config BCM63XX_CPU_6348
+ 	bool "support 6348 CPU"
+ 	select HW_HAS_PCI
++	select USB_ARCH_HAS_OHCI
++	select USB_OHCI_BIG_ENDIAN_DESC
++	select USB_OHCI_BIG_ENDIAN_MMIO
+ 
+ config BCM63XX_CPU_6358
+ 	bool "support 6358 CPU"
+ 	select HW_HAS_PCI
++	select USB_ARCH_HAS_OHCI
++	select USB_OHCI_BIG_ENDIAN_DESC
++	select USB_OHCI_BIG_ENDIAN_MMIO
+ endmenu
+ 
+ source "arch/mips/bcm63xx/boards/Kconfig"
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,5 +1,6 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
+-		   dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o
++		   dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
++		   dev-usb-ohci.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -25,6 +25,7 @@
+ #include <bcm63xx_dev_enet.h>
+ #include <bcm63xx_dev_dsp.h>
+ #include <bcm63xx_dev_pcmcia.h>
++#include <bcm63xx_dev_usb_ohci.h>
+ #include <board_bcm963xx.h>
+ 
+ #define PFX	"board_bcm963xx: "
+@@ -877,6 +878,9 @@ int __init board_register_devices(void)
+ 	    !board_get_mac_address(board.enet1.mac_addr))
+ 		bcm63xx_enet_register(1, &board.enet1);
+ 
++	if (board.has_ohci0)
++		bcm63xx_ohci_register();
++
+ 	if (board.has_dsp)
+ 		bcm63xx_dsp_register(&board.dsp);
+ 
+--- /dev/null
++++ b/arch/mips/bcm63xx/dev-usb-ohci.c
+@@ -0,0 +1,49 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_dev_usb_ohci.h>
++
++static struct resource ohci_resources[] = {
++	{
++		/* start & end filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		/* start filled at runtime */
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static u64 ohci_dmamask = ~(u32)0;
++
++static struct platform_device bcm63xx_ohci_device = {
++	.name		= "bcm63xx_ohci",
++	.id		= 0,
++	.num_resources	= ARRAY_SIZE(ohci_resources),
++	.resource	= ohci_resources,
++	.dev		= {
++		.dma_mask		= &ohci_dmamask,
++		.coherent_dma_mask	= 0xffffffff,
++	},
++};
++
++int __init bcm63xx_ohci_register(void)
++{
++	if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358())
++		return 0;
++
++	ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0);
++	ohci_resources[0].end = ohci_resources[0].start;
++	ohci_resources[0].end += RSET_OHCI_SIZE - 1;
++	ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0);
++	return platform_device_register(&bcm63xx_ohci_device);
++}
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
+@@ -0,0 +1,6 @@
++#ifndef BCM63XX_DEV_USB_OHCI_H_
++#define BCM63XX_DEV_USB_OHCI_H_
++
++int bcm63xx_ohci_register(void);
++
++#endif /* BCM63XX_DEV_USB_OHCI_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/008-usb-ehci-support.patch b/target/linux/brcm63xx/patches-2.6.37/008-usb-ehci-support.patch
new file mode 100644
index 0000000..0c236f0
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/008-usb-ehci-support.patch
@@ -0,0 +1,117 @@
+The bcm63xx SOC has an integrated EHCI controller, this patch adds
+platform device registration and change board code to register
+EHCI device when necessary.
+
+Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
+---
+ arch/mips/bcm63xx/Kconfig                          |    2 +
+ arch/mips/bcm63xx/Makefile                         |    2 +-
+ arch/mips/bcm63xx/boards/board_bcm963xx.c          |    4 ++
+ arch/mips/bcm63xx/dev-usb-ehci.c                   |   49 ++++++++++++++++++++
+ .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h        |    6 ++
+ 5 files changed, 62 insertions(+), 1 deletions(-)
+ create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c
+ create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
+
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -26,6 +26,8 @@ config BCM63XX_CPU_6358
+ 	select USB_ARCH_HAS_OHCI
+ 	select USB_OHCI_BIG_ENDIAN_DESC
+ 	select USB_OHCI_BIG_ENDIAN_MMIO
++	select USB_ARCH_HAS_EHCI
++	select USB_EHCI_BIG_ENDIAN_MMIO
+ endmenu
+ 
+ source "arch/mips/bcm63xx/boards/Kconfig"
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,6 +1,6 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
+ 		   dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
+-		   dev-usb-ohci.o
++		   dev-usb-ohci.o dev-usb-ehci.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -26,6 +26,7 @@
+ #include <bcm63xx_dev_dsp.h>
+ #include <bcm63xx_dev_pcmcia.h>
+ #include <bcm63xx_dev_usb_ohci.h>
++#include <bcm63xx_dev_usb_ehci.h>
+ #include <board_bcm963xx.h>
+ 
+ #define PFX	"board_bcm963xx: "
+@@ -878,6 +879,9 @@ int __init board_register_devices(void)
+ 	    !board_get_mac_address(board.enet1.mac_addr))
+ 		bcm63xx_enet_register(1, &board.enet1);
+ 
++	if (board.has_ehci0)
++		bcm63xx_ehci_register();
++
+ 	if (board.has_ohci0)
+ 		bcm63xx_ohci_register();
+ 
+--- /dev/null
++++ b/arch/mips/bcm63xx/dev-usb-ehci.c
+@@ -0,0 +1,49 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_dev_usb_ehci.h>
++
++static struct resource ehci_resources[] = {
++	{
++		/* start & end filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		/* start filled at runtime */
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static u64 ehci_dmamask = ~(u32)0;
++
++static struct platform_device bcm63xx_ehci_device = {
++	.name		= "bcm63xx_ehci",
++	.id		= 0,
++	.num_resources	= ARRAY_SIZE(ehci_resources),
++	.resource	= ehci_resources,
++	.dev		= {
++		.dma_mask		= &ehci_dmamask,
++		.coherent_dma_mask	= 0xffffffff,
++	},
++};
++
++int __init bcm63xx_ehci_register(void)
++{
++	if (!BCMCPU_IS_6358())
++		return 0;
++
++	ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0);
++	ehci_resources[0].end = ehci_resources[0].start;
++	ehci_resources[0].end += RSET_EHCI_SIZE - 1;
++	ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0);
++	return platform_device_register(&bcm63xx_ehci_device);
++}
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
+@@ -0,0 +1,6 @@
++#ifndef BCM63XX_DEV_USB_EHCI_H_
++#define BCM63XX_DEV_USB_EHCI_H_
++
++int bcm63xx_ehci_register(void);
++
++#endif /* BCM63XX_DEV_USB_EHCI_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/010-add_bcm63xx_ohci_controller.patch b/target/linux/brcm63xx/patches-2.6.37/010-add_bcm63xx_ohci_controller.patch
new file mode 100644
index 0000000..a7a66ec
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/010-add_bcm63xx_ohci_controller.patch
@@ -0,0 +1,202 @@
+Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
+---
+ drivers/usb/host/ohci-bcm63xx.c |  166 +++++++++++++++++++++++++++++++++++++++
+ drivers/usb/host/ohci-hcd.c     |    5 +
+ drivers/usb/host/ohci.h         |    2 +-
+ 3 files changed, 172 insertions(+), 1 deletions(-)
+ create mode 100644 drivers/usb/host/ohci-bcm63xx.c
+
+--- /dev/null
++++ b/drivers/usb/host/ohci-bcm63xx.c
+@@ -0,0 +1,166 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
++ */
++
++#include <linux/init.h>
++#include <linux/clk.h>
++#include <linux/platform_device.h>
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_regs.h>
++#include <bcm63xx_io.h>
++
++static struct clk *usb_host_clock;
++
++static int __devinit ohci_bcm63xx_start(struct usb_hcd *hcd)
++{
++	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
++	int ret;
++
++        /*
++         * port 2 can be shared with USB slave, but all boards seem to
++         * have only one host port populated, so we can hardcode it
++         */
++	ohci->num_ports = 1;
++
++	ret = ohci_init(ohci);
++	if (ret < 0)
++		return ret;
++
++	ret = ohci_run(ohci);
++	if (ret < 0) {
++		err("can't start %s", hcd->self.bus_name);
++		ohci_stop(hcd);
++		return ret;
++	}
++	return 0;
++}
++
++static const struct hc_driver ohci_bcm63xx_hc_driver = {
++	.description =		hcd_name,
++	.product_desc =		"BCM63XX integrated OHCI controller",
++	.hcd_priv_size =	sizeof(struct ohci_hcd),
++
++	.irq =			ohci_irq,
++	.flags =		HCD_USB11 | HCD_MEMORY,
++	.start =		ohci_bcm63xx_start,
++	.stop =			ohci_stop,
++	.shutdown =		ohci_shutdown,
++	.urb_enqueue =		ohci_urb_enqueue,
++	.urb_dequeue =		ohci_urb_dequeue,
++	.endpoint_disable =	ohci_endpoint_disable,
++	.get_frame_number =	ohci_get_frame,
++	.hub_status_data =	ohci_hub_status_data,
++	.hub_control =		ohci_hub_control,
++	.start_port_reset =	ohci_start_port_reset,
++};
++
++static int __devinit ohci_hcd_bcm63xx_drv_probe(struct platform_device *pdev)
++{
++	struct resource *res_mem;
++	struct usb_hcd *hcd;
++	struct ohci_hcd *ohci;
++	u32 reg;
++	int ret, irq;
++
++	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	irq = platform_get_irq(pdev, 0);
++	if (!res_mem || irq < 0)
++		return -ENODEV;
++
++	if (BCMCPU_IS_6348()) {
++		struct clk *clk;
++		/* enable USB host clock */
++		clk = clk_get(&pdev->dev, "usbh");
++		if (IS_ERR(clk))
++			return -ENODEV;
++
++		clk_enable(clk);
++		usb_host_clock = clk;
++		bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG);
++
++	} else if (BCMCPU_IS_6358()) {
++		reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_REG);
++		reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
++		reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
++		bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_REG);
++		/*
++		 * The magic value comes for the original vendor BSP
++		 * and is needed for USB to work. Datasheet does not
++		 * help, so the magic value is used as-is.
++		 */
++		bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, USBH_PRIV_TEST_REG);
++	} else
++		return 0;
++
++	hcd = usb_create_hcd(&ohci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx");
++	if (!hcd)
++		return -ENOMEM;
++	hcd->rsrc_start = res_mem->start;
++	hcd->rsrc_len = res_mem->end - res_mem->start + 1;
++
++	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
++		pr_debug("request_mem_region failed\n");
++		ret = -EBUSY;
++		goto out;
++	}
++
++	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
++	if (!hcd->regs) {
++		pr_debug("ioremap failed\n");
++		ret = -EIO;
++		goto out1;
++	}
++
++	ohci = hcd_to_ohci(hcd);
++	ohci->flags |= OHCI_QUIRK_BE_MMIO | OHCI_QUIRK_BE_DESC |
++		OHCI_QUIRK_FRAME_NO;
++	ohci_hcd_init(ohci);
++
++	ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
++	if (ret)
++		goto out2;
++
++	platform_set_drvdata(pdev, hcd);
++	return 0;
++
++out2:
++	iounmap(hcd->regs);
++out1:
++	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
++out:
++	usb_put_hcd(hcd);
++	return ret;
++}
++
++static int __devexit ohci_hcd_bcm63xx_drv_remove(struct platform_device *pdev)
++{
++	struct usb_hcd *hcd;
++
++	hcd = platform_get_drvdata(pdev);
++	usb_remove_hcd(hcd);
++	iounmap(hcd->regs);
++	usb_put_hcd(hcd);
++	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
++	if (usb_host_clock) {
++		clk_disable(usb_host_clock);
++		clk_put(usb_host_clock);
++	}
++	platform_set_drvdata(pdev, NULL);
++	return 0;
++}
++
++static struct platform_driver ohci_hcd_bcm63xx_driver = {
++	.probe		= ohci_hcd_bcm63xx_drv_probe,
++	.remove		= __devexit_p(ohci_hcd_bcm63xx_drv_remove),
++	.shutdown	= usb_hcd_platform_shutdown,
++	.driver		= {
++		.name	= "bcm63xx_ohci",
++		.owner	= THIS_MODULE,
++	},
++};
++
++MODULE_ALIAS("platform:bcm63xx_ohci");
+--- a/drivers/usb/host/ohci-hcd.c
++++ b/drivers/usb/host/ohci-hcd.c
+@@ -1067,6 +1067,11 @@ MODULE_LICENSE ("GPL");
+ #define PLATFORM_DRIVER		ohci_hcd_da8xx_driver
+ #endif
+ 
++#ifdef CONFIG_BCM63XX
++#include "ohci-bcm63xx.c"
++#define PLATFORM_DRIVER		ohci_hcd_bcm63xx_driver
++#endif
++
+ #if defined(CONFIG_CPU_SUBTYPE_SH7720) || \
+     defined(CONFIG_CPU_SUBTYPE_SH7721) || \
+     defined(CONFIG_CPU_SUBTYPE_SH7763) || \
+--- a/drivers/usb/host/ohci.h
++++ b/drivers/usb/host/ohci.h
+@@ -656,7 +656,7 @@ static inline u32 hc32_to_cpup (const st
+  * some big-endian SOC implementations.  Same thing happens with PSW access.
+  */
+ 
+-#ifdef CONFIG_PPC_MPC52xx
++#if defined(CONFIG_PPC_MPC52xx) || defined(CONFIG_BCM63XX)
+ #define big_endian_frame_no_quirk(ohci)	(ohci->flags & OHCI_QUIRK_FRAME_NO)
+ #else
+ #define big_endian_frame_no_quirk(ohci)	0
diff --git a/target/linux/brcm63xx/patches-2.6.37/011-add_bcm63xx_ehci_controller.patch b/target/linux/brcm63xx/patches-2.6.37/011-add_bcm63xx_ehci_controller.patch
new file mode 100644
index 0000000..e6e763d
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/011-add_bcm63xx_ehci_controller.patch
@@ -0,0 +1,178 @@
+Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
+---
+ drivers/usb/host/ehci-bcm63xx.c |  154 +++++++++++++++++++++++++++++++++++++++
+ drivers/usb/host/ehci-hcd.c     |    5 +
+ 2 files changed, 159 insertions(+), 0 deletions(-)
+ create mode 100644 drivers/usb/host/ehci-bcm63xx.c
+
+--- /dev/null
++++ b/drivers/usb/host/ehci-bcm63xx.c
+@@ -0,0 +1,154 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
++ */
++
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_regs.h>
++#include <bcm63xx_io.h>
++
++static int ehci_bcm63xx_setup(struct usb_hcd *hcd)
++{
++	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
++	int retval;
++
++	retval = ehci_halt(ehci);
++	if (retval)
++		return retval;
++
++	retval = ehci_init(hcd);
++	if (retval)
++		return retval;
++
++	ehci_reset(ehci);
++	ehci_port_power(ehci, 0);
++
++	return retval;
++}
++
++
++static const struct hc_driver ehci_bcm63xx_hc_driver = {
++	.description =		hcd_name,
++	.product_desc =		"BCM63XX integrated EHCI controller",
++	.hcd_priv_size =	sizeof(struct ehci_hcd),
++
++	.irq =			ehci_irq,
++	.flags =		HCD_MEMORY | HCD_USB2,
++
++	.reset =		ehci_bcm63xx_setup,
++	.start =		ehci_run,
++	.stop =			ehci_stop,
++	.shutdown =		ehci_shutdown,
++
++	.urb_enqueue =		ehci_urb_enqueue,
++	.urb_dequeue =		ehci_urb_dequeue,
++	.endpoint_disable =	ehci_endpoint_disable,
++
++	.get_frame_number =	ehci_get_frame,
++
++	.hub_status_data =	ehci_hub_status_data,
++	.hub_control =		ehci_hub_control,
++	.bus_suspend =		ehci_bus_suspend,
++	.bus_resume =		ehci_bus_resume,
++	.relinquish_port =	ehci_relinquish_port,
++	.port_handed_over =	ehci_port_handed_over,
++};
++
++static int __devinit ehci_hcd_bcm63xx_drv_probe(struct platform_device *pdev)
++{
++	struct resource *res_mem;
++	struct usb_hcd *hcd;
++	struct ehci_hcd *ehci;
++	u32 reg;
++	int ret, irq;
++
++	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	irq = platform_get_irq(pdev, 0);;
++	if (!res_mem || irq < 0)
++		return -ENODEV;
++
++	reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_REG);
++	reg &= ~USBH_PRIV_SWAP_EHCI_DATA_MASK;
++	reg |= USBH_PRIV_SWAP_EHCI_ENDN_MASK;
++	bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_REG);
++
++	/*
++	 * The magic value comes for the original vendor BSP and is
++	 * needed for USB to work. Datasheet does not help, so the
++	 * magic value is used as-is.
++	 */
++	bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, USBH_PRIV_TEST_REG);
++
++	hcd = usb_create_hcd(&ehci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx");
++	if (!hcd)
++		return -ENOMEM;
++	hcd->rsrc_start = res_mem->start;
++	hcd->rsrc_len = res_mem->end - res_mem->start + 1;
++
++	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
++		pr_debug("request_mem_region failed\n");
++		ret = -EBUSY;
++		goto out;
++	}
++
++	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
++	if (!hcd->regs) {
++		pr_debug("ioremap failed\n");
++		ret = -EIO;
++		goto out1;
++	}
++
++	ehci = hcd_to_ehci(hcd);
++	ehci->big_endian_mmio = 1;
++	ehci->big_endian_desc = 0;
++	ehci->caps = hcd->regs;
++	ehci->regs = hcd->regs +
++		HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
++	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
++	ehci->sbrn = 0x20;
++
++	ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
++	if (ret)
++		goto out2;
++
++	platform_set_drvdata(pdev, hcd);
++	return 0;
++
++out2:
++	iounmap(hcd->regs);
++out1:
++	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
++out:
++	usb_put_hcd(hcd);
++	return ret;
++}
++
++static int __devexit ehci_hcd_bcm63xx_drv_remove(struct platform_device *pdev)
++{
++	struct usb_hcd *hcd;
++
++	hcd = platform_get_drvdata(pdev);
++	usb_remove_hcd(hcd);
++	iounmap(hcd->regs);
++	usb_put_hcd(hcd);
++	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
++	platform_set_drvdata(pdev, NULL);
++	return 0;
++}
++
++static struct platform_driver ehci_hcd_bcm63xx_driver = {
++	.probe		= ehci_hcd_bcm63xx_drv_probe,
++	.remove		= __devexit_p(ehci_hcd_bcm63xx_drv_remove),
++	.shutdown	= usb_hcd_platform_shutdown,
++	.driver		= {
++		.name	= "bcm63xx_ehci",
++		.owner	= THIS_MODULE,
++	},
++};
++
++MODULE_ALIAS("platform:bcm63xx_ehci");
+--- a/drivers/usb/host/ehci-hcd.c
++++ b/drivers/usb/host/ehci-hcd.c
+@@ -1229,6 +1229,11 @@ MODULE_LICENSE ("GPL");
+ #define PLATFORM_DRIVER		ehci_octeon_driver
+ #endif
+ 
++#ifdef CONFIG_BCM63XX
++#include "ehci-bcm63xx.c"
++#define PLATFORM_DRIVER		ehci_hcd_bcm63xx_driver
++#endif
++
+ #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
+     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
+     !defined(XILINX_OF_PLATFORM_DRIVER)
diff --git a/target/linux/brcm63xx/patches-2.6.37/040-bcm963xx_flashmap.patch b/target/linux/brcm63xx/patches-2.6.37/040-bcm963xx_flashmap.patch
new file mode 100644
index 0000000..d08b9b1
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/040-bcm963xx_flashmap.patch
@@ -0,0 +1,159 @@
+From b1096781081b328fdac0e14a726ea04c2e9545c7 Mon Sep 17 00:00:00 2001
+From: Axel Gembe <ago@bastart.eu.org>
+Date: Mon, 12 May 2008 18:54:09 +0200
+Subject: [PATCH] bcm963xx: flashmap support
+
+Signed-off-by: Axel Gembe <ago@bastart.eu.org>
+---
+ arch/mips/bcm63xx/boards/board_bcm963xx.c |   19 +---------------
+ drivers/mtd/maps/bcm963xx-flash.c         |   34 ++++++++++++++++++++++++----
+ drivers/mtd/redboot.c                     |   13 ++++++++--
+ 3 files changed, 40 insertions(+), 26 deletions(-)
+
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -816,20 +816,6 @@ void __init board_setup(void)
+ 		panic("unexpected CPU for bcm963xx board");
+ }
+ 
+-static struct mtd_partition mtd_partitions[] = {
+-	{
+-		.name		= "cfe",
+-		.offset		= 0x0,
+-		.size		= 0x40000,
+-	}
+-};
+-
+-static struct physmap_flash_data flash_data = {
+-	.width			= 2,
+-	.nr_parts		= ARRAY_SIZE(mtd_partitions),
+-	.parts			= mtd_partitions,
+-};
+-
+ static struct resource mtd_resources[] = {
+ 	{
+ 		.start		= 0,	/* filled at runtime */
+@@ -839,12 +825,9 @@ static struct resource mtd_resources[] =
+ };
+ 
+ static struct platform_device mtd_dev = {
+-	.name			= "physmap-flash",
++	.name			= "bcm963xx-flash",
+ 	.resource		= mtd_resources,
+ 	.num_resources		= ARRAY_SIZE(mtd_resources),
+-	.dev			= {
+-		.platform_data	= &flash_data,
+-	},
+ };
+ 
+ static struct gpio_led_platform_data bcm63xx_led_data;
+--- a/drivers/mtd/maps/bcm963xx-flash.c
++++ b/drivers/mtd/maps/bcm963xx-flash.c
+@@ -27,6 +27,8 @@
+ #include <linux/vmalloc.h>
+ #include <linux/platform_device.h>
+ #include <linux/io.h>
++#include <linux/magic.h>
++#include <linux/jffs2.h>
+ 
+ #include <asm/mach-bcm63xx/bcm963xx_tag.h>
+ 
+@@ -35,6 +37,14 @@
+ 
+ #define PFX KBUILD_MODNAME ": "
+ 
++struct squashfs_super_block {
++	__le32 s_magic;
++	__le32 pad0[9];
++	__le64 bytes_used;
++};
++
++extern int parse_redboot_partitions(struct mtd_info *master, struct mtd_partition **pparts, unsigned long fis_origin);
++
+ static struct mtd_partition *parsed_parts;
+ 
+ static struct mtd_info *bcm963xx_mtd_info;
+@@ -56,7 +66,7 @@ static int parse_cfe_partitions(struct m
+ 	unsigned int rootfsaddr, kerneladdr, spareaddr;
+ 	unsigned int rootfslen, kernellen, sparelen, totallen;
+ 	int namelen = 0;
+-	int i;
++	int i, offset;
+ 	char *boardid;
+ 	char *tagversion;
+ 
+@@ -84,9 +94,11 @@ static int parse_cfe_partitions(struct m
+ 
+ 	kerneladdr = kerneladdr - BCM63XX_EXTENDED_SIZE;
+ 	rootfsaddr = kerneladdr + kernellen;
++
++	rootfslen = ( ( rootfslen % master->erasesize ) > 0 ? (((rootfslen / master->erasesize) + 1 ) * master->erasesize) : rootfslen);
++
+ 	spareaddr = roundup(totallen, master->erasesize) + master->erasesize;
+ 	sparelen = master->size - spareaddr - master->erasesize;
+-	rootfslen = spareaddr - rootfsaddr;
+ 
+ 	/* Determine number of partitions */
+ 	namelen = 8;
+@@ -214,9 +226,21 @@ static int bcm963xx_probe(struct platfor
+ 			}
+ 		}
+ 	} else {
+-		dev_info(&pdev->dev, "unsupported bootloader\n");
+-		err = -ENODEV;
+-		goto err_probe;
++		printk(KERN_INFO PFX "assuming RedBoot bootloader\n");
++		if (bcm963xx_mtd_info->size > 0x00400000) {
++			printk(KERN_INFO PFX "Support for extended flash memory size : 0x%lx ; ONLY 64MBIT SUPPORT\n", bcm963xx_mtd_info->size);
++			bcm963xx_map.virt = (u32)(BCM63XX_EXTENDED_SIZE);
++		}
++
++#ifdef CONFIG_MTD_REDBOOT_PARTS
++		if (parsed_nr_parts == 0) {
++			int ret = parse_redboot_partitions(bcm963xx_mtd_info, &parsed_parts, 0);
++			if (ret > 0) {
++				part_type = "RedBoot";
++				parsed_nr_parts = ret;
++			}
++		}
++#endif
+ 	}
+ 
+ 	return add_mtd_partitions(bcm963xx_mtd_info, parsed_parts,
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -57,7 +57,7 @@ static inline int redboot_checksum(struc
+ 	return 1;
+ }
+ 
+-static int parse_redboot_partitions(struct mtd_info *master,
++int parse_redboot_partitions(struct mtd_info *master,
+                              struct mtd_partition **pparts,
+                              unsigned long fis_origin)
+ {
+@@ -180,6 +180,14 @@ static int parse_redboot_partitions(stru
+ 		goto out;
+ 	}
+ 
++	if (!fis_origin) {
++		for (i = 0; i < numslots; i++) {
++			if (!strncmp(buf[i].name, "RedBoot", 8)) {
++				fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
++			}
++		}
++	}
++
+ 	for (i = 0; i < numslots; i++) {
+ 		struct fis_list *new_fl, **prev;
+ 
+@@ -202,9 +210,8 @@ static int parse_redboot_partitions(stru
+ 		new_fl->img = &buf[i];
+                 if (fis_origin) {
+                         buf[i].flash_base -= fis_origin;
+-                } else {
+-                        buf[i].flash_base &= master->size-1;
+                 }
++		buf[i].flash_base &= (master->size << 1) - 1;
+ 
+ 		/* I'm sure the JFFS2 code has done me permanent damage.
+ 		 * I now think the following is _normal_
diff --git a/target/linux/brcm63xx/patches-2.6.37/070_bcm63xx_enet_vlan_incoming_fixed.patch b/target/linux/brcm63xx/patches-2.6.37/070_bcm63xx_enet_vlan_incoming_fixed.patch
new file mode 100644
index 0000000..8211e29
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/070_bcm63xx_enet_vlan_incoming_fixed.patch
@@ -0,0 +1,11 @@
+--- a/drivers/net/bcm63xx_enet.c
++++ b/drivers/net/bcm63xx_enet.c
+@@ -1515,7 +1515,7 @@ static int compute_hw_mtu(struct bcm_ene
+ 	actual_mtu = mtu;
+ 
+ 	/* add ethernet header + vlan tag size */
+-	actual_mtu += VLAN_ETH_HLEN;
++	actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN;
+ 
+ 	if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU)
+ 		return -EINVAL;
diff --git a/target/linux/brcm63xx/patches-2.6.37/100-reset_buttons.patch b/target/linux/brcm63xx/patches-2.6.37/100-reset_buttons.patch
new file mode 100644
index 0000000..786c18b
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/100-reset_buttons.patch
@@ -0,0 +1,98 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -15,6 +15,8 @@
+ #include <linux/mtd/partitions.h>
+ #include <linux/mtd/physmap.h>
+ #include <linux/ssb/ssb.h>
++#include <linux/gpio_buttons.h>
++#include <linux/input.h>
+ #include <asm/addrspace.h>
+ #include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+@@ -296,6 +298,16 @@ static struct board_info __initdata boar
+ 			.active_low	= 1,
+ 		},
+ 	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++	},
+ };
+ 
+ static struct board_info __initdata board_96348gw = {
+@@ -354,6 +366,16 @@ static struct board_info __initdata boar
+ 			.active_low	= 1,
+ 		},
+ 	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 36,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++	},
+ };
+ 
+ static struct board_info __initdata board_FAST2404 = {
+@@ -838,12 +860,23 @@ static struct platform_device bcm63xx_gp
+ 	.dev.platform_data	= &bcm63xx_led_data,
+ };
+ 
++static struct gpio_buttons_platform_data bcm63xx_gpio_buttons_data = {
++	.poll_interval  = 20,
++};
++
++static struct platform_device bcm63xx_gpio_buttons_device = {
++	.name		= "gpio-buttons",
++	.id		= 0,
++	.dev.platform_data = &bcm63xx_gpio_buttons_data,
++};
++
+ /*
+  * third stage init callback, register all board devices.
+  */
+ int __init board_register_devices(void)
+ {
+ 	u32 val;
++	int button_count = 0;
+ 
+ 	if (board.has_uart0)
+ 		bcm63xx_uart_register(0);
+@@ -888,5 +921,16 @@ int __init board_register_devices(void)
+ 
+ 	platform_device_register(&bcm63xx_gpio_leds);
+ 
++	/* count number of BUTTONs defined by this device */
++	while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
++		button_count++;
++
++	if (button_count) {
++		bcm63xx_gpio_buttons_data.nbuttons = button_count;
++		bcm63xx_gpio_buttons_data.buttons = board.buttons;
++
++		platform_device_register(&bcm63xx_gpio_buttons_device);
++	}
++
+ 	return 0;
+ }
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -57,6 +57,9 @@ struct board_info {
+ 
+ 	/* GPIO LEDs */
+ 	struct gpio_led leds[5];
++
++	/* Buttons */
++	struct gpio_button buttons[2];
+ };
+ 
+ #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/110-gpiodev.patch b/target/linux/brcm63xx/patches-2.6.37/110-gpiodev.patch
new file mode 100644
index 0000000..99ee29f
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/110-gpiodev.patch
@@ -0,0 +1,22 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -852,6 +852,10 @@ static struct platform_device mtd_dev = 
+ 	.num_resources		= ARRAY_SIZE(mtd_resources),
+ };
+ 
++static struct resource gpiodev_resource = {
++	.start			= 0xFFFFFFFF,
++};
++
+ static struct gpio_led_platform_data bcm63xx_led_data;
+ 
+ static struct platform_device bcm63xx_gpio_leds = {
+@@ -916,6 +920,8 @@ int __init board_register_devices(void)
+ 
+ 	platform_device_register(&mtd_dev);
+ 
++	platform_device_register_simple("GPIODEV", 0, &gpiodev_resource, 1);
++
+ 	bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
+ 	bcm63xx_led_data.leds = board.leds;
+ 
diff --git a/target/linux/brcm63xx/patches-2.6.37/150-alice_gate2_leds.patch b/target/linux/brcm63xx/patches-2.6.37/150-alice_gate2_leds.patch
new file mode 100644
index 0000000..fa5ca81
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/150-alice_gate2_leds.patch
@@ -0,0 +1,113 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -588,6 +588,99 @@ static struct board_info __initdata boar
+ 
+ 	.has_ohci0 = 1,
+ 	.has_ehci0 = 1,
++
++	.leds = {
++		/*Each led on alice gate is bi-color */
++		{
++			.name		= "power:red",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power:green",
++			.gpio		= 4,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "service:red",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:green",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++		{
++			.name		= "adsl:red",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "adsl:green",
++			.gpio		= 10,
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi:red",
++			.gpio		= 23,
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi:green",
++			.gpio		= 22,
++			.active_low	= 1,
++		},
++		{
++			.name		= "internet:red",
++			.gpio		= 25,
++			.active_low	= 1,
++		},
++		{
++			.name		= "internet:green",
++			.gpio		= 24,
++			.active_low	= 1,
++		},
++		{
++			.name		= "usr1:red",
++			.gpio		= 27,
++			.active_low	= 1,
++		},
++		{
++			.name		= "usr1:green",
++			.gpio		= 26,
++			.active_low	= 1,
++		},
++		{
++			.name		= "usr2:red",
++			.gpio		= 30,
++			.active_low	= 1,
++		},
++		{
++			.name		= "usr2:green",
++			.gpio		= 29,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc           = "reset",
++			.gpio           = 37,
++			.active_low     = 1,
++			.type           = EV_KEY,
++			.code           = KEY_RESTART,
++			.threshold      = 3,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.threshold	= 3,
++		},
++	},
+ };
+ 
+ static struct board_info __initdata board_DWVS0 = {
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -56,7 +56,7 @@ struct board_info {
+ 	struct bcm63xx_dsp_platform_data dsp;
+ 
+ 	/* GPIO LEDs */
+-	struct gpio_led leds[5];
++	struct gpio_led leds[14];
+ 
+ 	/* Buttons */
+ 	struct gpio_button buttons[2];
diff --git a/target/linux/brcm63xx/patches-2.6.37/170-board_livebox.patch b/target/linux/brcm63xx/patches-2.6.37/170-board_livebox.patch
new file mode 100644
index 0000000..6c39045
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/170-board_livebox.patch
@@ -0,0 +1,251 @@
+--- a/arch/mips/bcm63xx/boards/Kconfig
++++ b/arch/mips/bcm63xx/boards/Kconfig
+@@ -8,4 +8,10 @@ config BOARD_BCM963XX
+ 	select SSB
+        help
+ 
++config BOARD_LIVEBOX
++	bool "Inventel Livebox(es) boards"
++	select SSB
++	help
++	 Inventel Livebox boards using the RedBoot bootloader.
++
+ endchoice
+--- a/arch/mips/bcm63xx/boards/Makefile
++++ b/arch/mips/bcm63xx/boards/Makefile
+@@ -1,3 +1,4 @@
+ obj-$(CONFIG_BOARD_BCM963XX)		+= board_bcm963xx.o
++obj-$(CONFIG_BOARD_LIVEBOX)		+= board_livebox.o
+ 
+ EXTRA_CFLAGS += -Werror
+--- /dev/null
++++ b/arch/mips/bcm63xx/boards/board_livebox.c
+@@ -0,0 +1,228 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/string.h>
++#include <linux/platform_device.h>
++#include <linux/mtd/mtd.h>
++#include <linux/mtd/partitions.h>
++#include <linux/mtd/physmap.h>
++#include <linux/input.h>
++#include <linux/gpio_buttons.h>
++#include <asm/addrspace.h>
++#include <bcm63xx_board.h>
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_regs.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_dev_uart.h>
++#include <bcm63xx_dev_pci.h>
++#include <bcm63xx_dev_enet.h>
++#include <bcm63xx_dev_pcmcia.h>
++#include <bcm63xx_dev_usb_ohci.h>
++#include <bcm63xx_dev_usb_ehci.h>
++#include <board_bcm963xx.h>
++
++#define PFX	"board_livebox: "
++
++static unsigned int mac_addr_used = 0;
++static struct board_info board;
++
++/*
++ * known 6348 boards
++ */
++#ifdef CONFIG_BCM63XX_CPU_6348
++static struct board_info __initdata board_livebox = {
++	.name				= "Livebox",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0			= 1,
++	.has_pccard			= 1,
++	.has_ehci0			= 1,
++};
++#endif
++
++/*
++ * all boards
++ */
++static const struct board_info __initdata *bcm963xx_boards[] = {
++#ifdef CONFIG_BCM63XX_CPU_6348
++	&board_livebox
++#endif
++};
++
++/*
++ * early init callback
++ */
++void __init board_prom_init(void)
++{
++	u32 val;
++
++	/* read base address of boot chip select (0) */
++	val = bcm_mpi_readl(MPI_CSBASE_REG(0));
++	val &= MPI_CSBASE_BASE_MASK;
++
++	/* assume board is a Livebox */
++	memcpy(&board, bcm963xx_boards[0], sizeof(board));
++
++	/* setup pin multiplexing depending on board enabled device,
++	 * this has to be done this early since PCI init is done
++	 * inside arch_initcall */
++	val = 0;
++
++	if (board.has_pci) {
++		bcm63xx_pci_enabled = 1;
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G2_PCI;
++	}
++
++	if (board.has_pccard) {
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G1_MII_PCCARD;
++	}
++
++	if (board.has_enet0 && !board.enet0.use_internal_phy) {
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G3_EXT_MII |
++				GPIO_MODE_6348_G0_EXT_MII;
++	}
++
++	if (board.has_enet1 && !board.enet1.use_internal_phy) {
++		if (BCMCPU_IS_6348())
++			val |= GPIO_MODE_6348_G3_EXT_MII |
++				GPIO_MODE_6348_G0_EXT_MII;
++	}
++
++	bcm_gpio_writel(val, GPIO_MODE_REG);
++}
++
++/*
++ * second stage init callback, good time to panic if we couldn't
++ * identify on which board we're running since early printk is working
++ */
++void __init board_setup(void)
++{
++	if (!board.name[0])
++		panic("unable to detect bcm963xx board");
++	printk(KERN_INFO PFX "board name: %s\n", board.name);
++
++	/* make sure we're running on expected cpu */
++	if (bcm63xx_get_cpu_id() != board.expected_cpu_id)
++		panic("unexpected CPU for bcm963xx board");
++}
++
++/*
++ * return board name for /proc/cpuinfo
++ */
++const char *board_get_name(void)
++{
++	return board.name;
++}
++
++/*
++ * register & return a new board mac address
++ */
++
++static int board_get_mac_address(u8 *mac)
++{
++	u8 default_mac[ETH_ALEN] = {0x00, 0x07, 0x3A, 0x00, 0x00, 0x00};
++	u8 *p;
++	int count;
++
++	memcpy(mac, default_mac, ETH_ALEN);
++
++	p = mac + ETH_ALEN - 1;
++	count = mac_addr_used;
++
++	while (count--) {
++		do {
++			(*p)++;
++			if (*p != 0)
++				break;
++			p--;
++		} while (p != mac);
++	}
++
++	if (p == mac) {
++		printk(KERN_ERR PFX "unable to fetch mac address\n");
++		return -ENODEV;
++	}
++        mac_addr_used++;
++
++	return 0;
++}
++
++static struct resource mtd_resources[] = {
++	{
++		.start          = 0,    /* filled at runtime */
++		.end            = 0,    /* filled at runtime */
++		.flags          = IORESOURCE_MEM,
++	}
++};
++
++static struct platform_device mtd_dev = {
++	.name                   = "bcm963xx-flash",
++	.resource               = mtd_resources,
++	.num_resources          = ARRAY_SIZE(mtd_resources),
++};
++
++
++/*
++ * third stage init callback, register all board devices.
++ */
++int __init board_register_devices(void)
++{
++	u32 val;
++
++	if (board.has_uart0)
++		bcm63xx_uart_register(0);
++
++	if (board.has_pccard)
++		bcm63xx_pcmcia_register();
++
++	if (board.has_enet0 &&
++	    !board_get_mac_address(board.enet0.mac_addr))
++		bcm63xx_enet_register(0, &board.enet0);
++
++	if (board.has_enet1 &&
++	    !board_get_mac_address(board.enet1.mac_addr))
++		bcm63xx_enet_register(1, &board.enet1);
++
++	if (board.has_ohci0)
++		bcm63xx_ohci_register();
++
++	if (board.has_ehci0)
++		bcm63xx_ehci_register();
++
++
++	/* read base address of boot chip select (0) */
++	val = bcm_mpi_readl(MPI_CSBASE_REG(0));
++	val &= MPI_CSBASE_BASE_MASK;
++	mtd_resources[0].start = val;
++	mtd_resources[0].end = 0x1FFFFFFF;
++
++	platform_device_register(&mtd_dev);
++
++	return 0;
++}
++
diff --git a/target/linux/brcm63xx/patches-2.6.37/180-udc_preliminary_support.patch b/target/linux/brcm63xx/patches-2.6.37/180-udc_preliminary_support.patch
new file mode 100644
index 0000000..2f6a27e
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/180-udc_preliminary_support.patch
@@ -0,0 +1,243 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -29,6 +29,7 @@
+ #include <bcm63xx_dev_pcmcia.h>
+ #include <bcm63xx_dev_usb_ohci.h>
+ #include <bcm63xx_dev_usb_ehci.h>
++#include <bcm63xx_dev_usb_udc.h>
+ #include <board_bcm963xx.h>
+ 
+ #define PFX	"board_bcm963xx: "
+@@ -400,6 +401,8 @@ static struct board_info __initdata boar
+ 	.has_ohci0			= 1,
+ 	.has_pccard			= 1,
+ 	.has_ehci0			= 1,
++
++	.has_udc0			= 1,
+ };
+ 
+ static struct board_info __initdata board_rta1025w_16 = {
+@@ -1001,6 +1004,9 @@ int __init board_register_devices(void)
+ 	if (board.has_dsp)
+ 		bcm63xx_dsp_register(&board.dsp);
+ 
++	if (board.has_udc0)
++		bcm63xx_udc_register();
++
+ 	/* read base address of boot chip select (0) */
+ 	if (BCMCPU_IS_6345())
+ 		val = 0x1fc00000;
+--- /dev/null
++++ b/arch/mips/bcm63xx/dev-usb-udc.c
+@@ -0,0 +1,58 @@
++/*
++ * Copyright (C) 2009	Henk Vergonet <Henk.Vergonet@gmail.com>
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
++ */
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <bcm63xx_cpu.h>
++
++static struct resource udc_resources[] = {
++	{
++		.start		= -1, /* filled at runtime */
++		.end		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		.start		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static u64 udc_dmamask = ~(u32)0;
++
++static struct platform_device bcm63xx_udc_device = {
++	.name		= "bcm63xx-udc",
++	.id		= 0,
++	.num_resources	= ARRAY_SIZE(udc_resources),
++	.resource	= udc_resources,
++	.dev		= {
++		.dma_mask		= &udc_dmamask,
++		.coherent_dma_mask	= 0xffffffff,
++	},
++};
++
++int __init bcm63xx_udc_register(void)
++{
++	if (!BCMCPU_IS_6338() && !BCMCPU_IS_6345() && !BCMCPU_IS_6348())
++		return 0;
++
++	udc_resources[0].start = bcm63xx_regset_address(RSET_UDC0);
++	udc_resources[0].end = udc_resources[0].start;
++	udc_resources[0].end += RSET_UDC_SIZE - 1;
++	udc_resources[1].start = bcm63xx_get_irq_number(IRQ_UDC0);
++	return platform_device_register(&bcm63xx_udc_device);
++}
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+@@ -127,7 +127,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6338_UART1_BASE		(0xdeadbeef)
+ #define BCM_6338_GPIO_BASE		(0xfffe0400)
+ #define BCM_6338_SPI_BASE		(0xfffe0c00)
+-#define BCM_6338_UDC0_BASE		(0xdeadbeef)
++#define BCM_6338_UDC0_BASE		(0xfffe3000)
+ #define BCM_6338_USBDMA_BASE		(0xfffe2400)
+ #define BCM_6338_OHCI0_BASE		(0xdeadbeef)
+ #define BCM_6338_OHCI_PRIV_BASE		(0xfffe3000)
+@@ -158,7 +158,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6345_UART1_BASE		(0xdeadbeef)
+ #define BCM_6345_GPIO_BASE		(0xfffe0400)
+ #define BCM_6345_SPI_BASE		(0xdeadbeef)
+-#define BCM_6345_UDC0_BASE		(0xdeadbeef)
++#define BCM_6345_UDC0_BASE		(0xfffe2100)
+ #define BCM_6345_USBDMA_BASE		(0xfffe2800)
+ #define BCM_6345_ENET0_BASE		(0xfffe1800)
+ #define BCM_6345_ENETDMA_BASE		(0xfffe2800)
+@@ -215,7 +215,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6358_UART1_BASE		(0xfffe0120)
+ #define BCM_6358_GPIO_BASE		(0xfffe0080)
+ #define BCM_6358_SPI_BASE		(0xdeadbeef)
+-#define BCM_6358_UDC0_BASE		(0xfffe0800)
++#define BCM_6358_UDC0_BASE		(0xfffe0400)
+ #define BCM_6358_OHCI0_BASE		(0xfffe1400)
+ #define BCM_6358_OHCI_PRIV_BASE		(0xdeadbeef)
+ #define BCM_6358_USBH_PRIV_BASE		(0xfffe1500)
+@@ -444,6 +444,7 @@ enum bcm63xx_irq {
+ 	IRQ_UART0,
+ 	IRQ_UART1,
+ 	IRQ_DSL,
++	IRQ_UDC0,
+ 	IRQ_ENET0,
+ 	IRQ_ENET1,
+ 	IRQ_ENET_PHY,
+@@ -486,7 +487,7 @@ enum bcm63xx_irq {
+ #define BCM_6345_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+ #define BCM_6345_DSL_IRQ		(IRQ_INTERNAL_BASE + 3)
+ #define BCM_6345_ATM_IRQ		(IRQ_INTERNAL_BASE + 4)
+-#define BCM_6345_USB_IRQ		(IRQ_INTERNAL_BASE + 5)
++#define BCM_6345_UDC0_IRQ		(IRQ_INTERNAL_BASE + 5)
+ #define BCM_6345_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+ #define BCM_6345_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 12)
+ #define BCM_6345_ENET0_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 13 + 1)
+@@ -508,10 +509,17 @@ enum bcm63xx_irq {
+ #define BCM_6348_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+ #define BCM_6348_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+ #define BCM_6348_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
++#define BCM_6348_UDC0_IRQ		(IRQ_INTERNAL_BASE + 6)
+ #define BCM_6348_ENET1_IRQ		(IRQ_INTERNAL_BASE + 7)
+ #define BCM_6348_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+ #define BCM_6348_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
+ #define BCM_6348_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 12)
++#define BCM_6348_USB_CNTL_RX_DMA_IRQ	(IRQ_INTERNAL_BASE + 14)
++#define BCM_6348_USB_CNTL_TX_DMA_IRQ	(IRQ_INTERNAL_BASE + 15)
++#define BCM_6348_USB_BULK_RX_DMA_IRQ	(IRQ_INTERNAL_BASE + 16)
++#define BCM_6348_USB_BULK_TX_DMA_IRQ	(IRQ_INTERNAL_BASE + 17)
++#define BCM_6348_USB_ISO_RX_DMA_IRQ	(IRQ_INTERNAL_BASE + 18)
++#define BCM_6348_USB_ISO_TX_DMA_IRQ	(IRQ_INTERNAL_BASE + 19)
+ #define BCM_6348_ENET0_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 20)
+ #define BCM_6348_ENET0_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 21)
+ #define BCM_6348_ENET1_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 22)
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_udc.h
+@@ -0,0 +1,6 @@
++#ifndef BCM63XX_DEV_USB_UDC_H_
++#define BCM63XX_DEV_USB_UDC_H_
++
++int bcm63xx_udc_register(void);
++
++#endif /* BCM63XX_DEV_USB_UDC_H_ */
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -47,6 +47,7 @@ struct board_info {
+ 	unsigned int	has_dsp:1;
+ 	unsigned int	has_uart0:1;
+ 	unsigned int	has_uart1:1;
++	unsigned int	has_udc0:1;
+ 
+ 	/* ethernet config */
+ 	struct bcm63xx_enet_platform_data enet0;
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,6 +1,6 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
+ 		   dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
+-		   dev-usb-ohci.o dev-usb-ehci.o
++		   dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- a/arch/mips/bcm63xx/clk.c
++++ b/arch/mips/bcm63xx/clk.c
+@@ -141,6 +141,30 @@ static struct clk clk_usbh = {
+ };
+ 
+ /*
++ * USB slave clock
++ */
++static void usbs_set(struct clk *clk, int enable)
++{
++	u32 mask;
++
++	switch(bcm63xx_get_cpu_id()) {
++	case BCM6338_CPU_ID:
++		mask = CKCTL_6338_USBS_EN;
++		break;
++	case BCM6348_CPU_ID:
++		mask = CKCTL_6348_USBS_EN;
++		break;
++	default:
++		return;
++	}
++	bcm_hwclock_set(mask, enable);
++}
++
++static struct clk clk_usbs = {
++	.set    = usbs_set,
++};
++
++/*
+  * SPI clock
+  */
+ static void spi_set(struct clk *clk, int enable)
+@@ -208,6 +232,8 @@ struct clk *clk_get(struct device *dev, 
+ 		return &clk_ephy;
+ 	if (!strcmp(id, "usbh"))
+ 		return &clk_usbh;
++	if (!strcmp(id, "usbs"))
++		return &clk_usbs;
+ 	if (!strcmp(id, "spi"))
+ 		return &clk_spi;
+ 	if (!strcmp(id, "periph"))
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -7,6 +7,7 @@ config BCM63XX_CPU_6338
+ 	select USB_ARCH_HAS_OHCI
+ 	select USB_OHCI_BIG_ENDIAN_DESC
+ 	select USB_OHCI_BIG_ENDIAN_MMIO
++	select USB_ARCH_HAS_UDC
+ 
+ config BCM63XX_CPU_6345
+ 	bool "support 6345 CPU"
+@@ -19,6 +20,7 @@ config BCM63XX_CPU_6348
+ 	select USB_ARCH_HAS_OHCI
+ 	select USB_OHCI_BIG_ENDIAN_DESC
+ 	select USB_OHCI_BIG_ENDIAN_MMIO
++	select USB_ARCH_HAS_UDC
+ 
+ config BCM63XX_CPU_6358
+ 	bool "support 6358 CPU"
diff --git a/target/linux/brcm63xx/patches-2.6.37/200-extended-platform-devices.patch b/target/linux/brcm63xx/patches-2.6.37/200-extended-platform-devices.patch
new file mode 100644
index 0000000..70637e5
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/200-extended-platform-devices.patch
@@ -0,0 +1,25 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1007,6 +1007,9 @@ int __init board_register_devices(void)
+ 	if (board.has_udc0)
+ 		bcm63xx_udc_register();
+ 
++	if (board.num_devs)
++		platform_add_devices(board.devs, board.num_devs);
++
+ 	/* read base address of boot chip select (0) */
+ 	if (BCMCPU_IS_6345())
+ 		val = 0x1fc00000;
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -61,6 +61,10 @@ struct board_info {
+ 
+ 	/* Buttons */
+ 	struct gpio_button buttons[2];
++
++	/* Additional platform devices */
++	struct platform_device **devs;
++	unsigned int	num_devs;
+ };
+ 
+ #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/200-spi-board-info.patch b/target/linux/brcm63xx/patches-2.6.37/200-spi-board-info.patch
new file mode 100644
index 0000000..d73d6f0
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/200-spi-board-info.patch
@@ -0,0 +1,25 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1010,6 +1010,9 @@ int __init board_register_devices(void)
+ 	if (board.num_devs)
+ 		platform_add_devices(board.devs, board.num_devs);
+ 
++	if (board.num_spis)
++		spi_register_board_info(board.spis, board.num_spis);
++
+ 	/* read base address of boot chip select (0) */
+ 	if (BCMCPU_IS_6345())
+ 		val = 0x1fc00000;
+--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
+@@ -65,6 +65,10 @@ struct board_info {
+ 	/* Additional platform devices */
+ 	struct platform_device **devs;
+ 	unsigned int	num_devs;
++
++	/* Additional platform devices */
++	struct spi_board_info *spis;
++	unsigned int	num_spis;
+ };
+ 
+ #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/220-board-D4PW.patch b/target/linux/brcm63xx/patches-2.6.37/220-board-D4PW.patch
new file mode 100644
index 0000000..1e630d1
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/220-board-D4PW.patch
@@ -0,0 +1,60 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -464,6 +464,49 @@ static struct board_info __initdata boar
+ 
+ 	.has_ohci0 = 1,
+ };
++
++static struct board_info __initdata board_96348_D4PW = {
++	.name				= "D-4P-W",
++	.expected_cpu_id		= 0x6348,
++
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0			= 1,
++	.has_ehci0			= 1,
++
++	.leds = {
++		{
++			.name		= "ppp",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "ppp-fail",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++
++		},
++	},
++
++};
++
+ #endif
+ 
+ /*
+@@ -728,6 +771,7 @@ static const struct board_info __initdat
+ 	&board_DV201AMR,
+ 	&board_96348gw_a,
+ 	&board_rta1025w_16,
++	&board_96348_D4PW,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/221-board-NB4.patch b/target/linux/brcm63xx/patches-2.6.37/221-board-NB4.patch
new file mode 100644
index 0000000..c2d1056
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/221-board-NB4.patch
@@ -0,0 +1,569 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -17,6 +17,9 @@
+ #include <linux/ssb/ssb.h>
+ #include <linux/gpio_buttons.h>
+ #include <linux/input.h>
++#include <linux/spi/spi.h>
++#include <linux/spi/spi_gpio.h>
++#include <linux/spi/74x164.h>
+ #include <asm/addrspace.h>
+ #include <bcm63xx_board.h>
+ #include <bcm63xx_cpu.h>
+@@ -34,6 +37,12 @@
+ 
+ #define PFX	"board_bcm963xx: "
+ 
++#define NB4_PID_OFFSET		0xff80
++#define NB4_74X164_GPIO_BASE	64
++#define NB4_SPI_GPIO_MOSI	7
++#define NB4_SPI_GPIO_CLK	6
++#define NB4_74HC64_GPIO(X)	(NB4_74X164_GPIO_BASE + (X))
++
+ static struct bcm963xx_nvram nvram;
+ static unsigned int mac_addr_used;
+ static struct board_info board;
+@@ -749,6 +758,502 @@ static struct board_info __initdata boar
+ 
+ 	.has_ohci0			= 1,
+ };
++
++struct spi_gpio_platform_data nb4_spi_gpio_data = {
++	.sck		= NB4_SPI_GPIO_CLK,
++	.mosi		= NB4_SPI_GPIO_MOSI,
++	.miso		= SPI_GPIO_NO_MISO,
++	.num_chipselect	= 1,
++};
++
++
++static struct platform_device nb4_spi_gpio = {
++	.name = "spi_gpio",
++	.id   = 1,
++	.dev = {
++		.platform_data = &nb4_spi_gpio_data,
++	},
++};
++
++static struct platform_device * __initdata nb4_devices[] = {
++	&nb4_spi_gpio,
++};
++
++const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = {
++	.base = NB4_74X164_GPIO_BASE
++};
++
++static struct spi_board_info nb4_spi_devices[] = {
++	{
++		.modalias = "74x164",
++		.max_speed_hz = 781000,
++		.bus_num = 1,
++		.controller_data = (void *) SPI_GPIO_NO_CHIPSELECT,
++		.mode = SPI_MODE_0,
++		.platform_data = &nb4_74x164_platform_data
++	}
++};
++
++static struct board_info __initdata board_nb4_ser_r0 = {
++	.name				= "NB4-SER-r0",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.has_udc0			= 1,
++
++	.leds = {
++		{
++			.name		= "adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "traffic",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi",
++			.gpio		= 15,
++			.active_low	= 1,
++		},
++		{
++			.name		= "alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:red",
++			.gpio		= 29,
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:green",
++			.gpio		= 30,
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:blue",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.threshold	= 3,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_ser_r1 = {
++	.name				= "NB4-SER-r1",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.has_udc0			= 1,
++
++	.leds = {
++		{
++			.name		= "adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "traffic",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi",
++			.gpio		= 15,
++			.active_low	= 1,
++		},
++		{
++			.name		= "alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:red",
++			.gpio		= 29,
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:green",
++			.gpio		= 30,
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:blue",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.threshold	= 3,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_ser_r2 = {
++	.name				= "NB4-SER-r2",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "traffic",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi",
++			.gpio		= 15,
++			.active_low	= 1,
++		},
++		{
++			.name		= "alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:red",
++			.gpio		= 29,
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:green",
++			.gpio		= 30,
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:blue",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.threshold	= 3,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_fxc_r1 = {
++	.name				= "NB4-FXC-r1",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.has_udc0			= 1,
++
++	.leds = {
++		{
++			.name		= "adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "traffic",
++			.gpio		= 2,
++		},
++		{
++			.name		= "tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi",
++			.gpio		= 15,
++		},
++		{
++			.name		= "alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:red",
++			.gpio		= 29,
++		},
++		{
++			.name		= "service:green",
++			.gpio		= 30,
++		},
++		{
++			.name		= "service:blue",
++			.gpio		= 4,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.threshold	= 3,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
++
++static struct board_info __initdata board_nb4_fxc_r2 = {
++	.name				= "NB4-FXC-r2",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "adsl",
++			.gpio		= NB4_74HC64_GPIO(4),
++			.active_low	= 1,
++		},
++		{
++			.name		= "traffic",
++			.gpio		= 2,
++		},
++		{
++			.name		= "tel",
++			.gpio		= NB4_74HC64_GPIO(3),
++			.active_low	= 1,
++		},
++		{
++			.name		= "tv",
++			.gpio		= NB4_74HC64_GPIO(2),
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi",
++			.gpio		= 15,
++		},
++		{
++			.name		= "alarm",
++			.gpio		= NB4_74HC64_GPIO(0),
++			.active_low	= 1,
++		},
++		{
++			.name		= "service:red",
++			.gpio		= 29,
++		},
++		{
++			.name		= "service:green",
++			.gpio		= 30,
++		},
++		{
++			.name		= "service:blue",
++			.gpio		= 4,
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.threshold	= 3,
++		},
++	},
++	.devs = nb4_devices,
++	.num_devs = ARRAY_SIZE(nb4_devices),
++	.spis = nb4_spi_devices,
++	.num_spis = ARRAY_SIZE(nb4_spi_devices),
++};
+ #endif
+ 
+ /*
+@@ -779,9 +1284,30 @@ static const struct board_info __initdat
+ 	&board_96358vw2,
+ 	&board_AGPFS0,
+ 	&board_DWVS0,
++	&board_nb4_ser_r0,
++	&board_nb4_ser_r1,
++	&board_nb4_ser_r2,
++	&board_nb4_fxc_r1,
++	&board_nb4_fxc_r2,
+ #endif
+ };
+ 
++static void __init nb4_nvram_fixup(void)
++{
++	u8 *boot_addr, *p;
++	u32 val;
++
++	if (BCMCPU_IS_6358() && (!strcmp(nvram.name, "96358VW"))) {
++		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
++		val &= MPI_CSBASE_BASE_MASK;
++		boot_addr = (u8 *)KSEG1ADDR(val);
++		/* Extract nb4 PID */
++		p = boot_addr + NB4_PID_OFFSET;
++		if (!memcmp(p, "NB4-", 4))
++			memcpy(nvram.name, p, sizeof("NB4-XXX-rX"));
++	}
++}
++
+ /*
+  * Register a sane SPROMv2 to make the on-board
+  * bcm4318 WLAN work
+@@ -899,6 +1425,9 @@ void __init board_prom_init(void)
+ 		return;
+ 	}
+ 
++	/* Fixup broken nb4 board name */
++	nb4_nvram_fixup();
++
+ 	/* find board by name */
+ 	for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
+ 		if (strncmp(nvram.name, bcm963xx_boards[i]->name,
diff --git a/target/linux/brcm63xx/patches-2.6.37/240-spi.patch b/target/linux/brcm63xx/patches-2.6.37/240-spi.patch
new file mode 100644
index 0000000..5a81a08
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/240-spi.patch
@@ -0,0 +1,1002 @@
+--- a/arch/mips/bcm63xx/cpu.c
++++ b/arch/mips/bcm63xx/cpu.c
+@@ -58,6 +58,7 @@ static const unsigned long bcm96338_regs
+ 
+ static const int bcm96338_irqs[] = {
+ 	[IRQ_TIMER]		= BCM_6338_TIMER_IRQ,
++	[IRQ_SPI]		= BCM_6338_SPI_IRQ,
+ 	[IRQ_UART0]		= BCM_6338_UART0_IRQ,
+ 	[IRQ_DSL]		= BCM_6338_DSL_IRQ,
+ 	[IRQ_ENET0]		= BCM_6338_ENET0_IRQ,
+@@ -132,6 +133,7 @@ static const unsigned long bcm96348_regs
+ 
+ static const int bcm96348_irqs[] = {
+ 	[IRQ_TIMER]		= BCM_6348_TIMER_IRQ,
++	[IRQ_SPI]		= BCM_6348_SPI_IRQ,
+ 	[IRQ_UART0]		= BCM_6348_UART0_IRQ,
+ 	[IRQ_DSL]		= BCM_6348_DSL_IRQ,
+ 	[IRQ_ENET0]		= BCM_6348_ENET0_IRQ,
+@@ -175,6 +177,7 @@ static const unsigned long bcm96358_regs
+ 
+ static const int bcm96358_irqs[] = {
+ 	[IRQ_TIMER]		= BCM_6358_TIMER_IRQ,
++	[IRQ_SPI]		= BCM_6358_SPI_IRQ,
+ 	[IRQ_UART0]		= BCM_6358_UART0_IRQ,
+ 	[IRQ_UART1]		= BCM_6358_UART1_IRQ,
+ 	[IRQ_DSL]		= BCM_6358_DSL_IRQ,
+--- /dev/null
++++ b/arch/mips/bcm63xx/dev-spi.c
+@@ -0,0 +1,128 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License.  See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
++ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
++ */
++
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++
++#include <bcm63xx_cpu.h>
++#include <bcm63xx_dev_spi.h>
++#include <bcm63xx_regs.h>
++
++#ifdef BCMCPU_RUNTIME_DETECT
++/*
++ * register offsets
++ */
++static const unsigned long bcm96338_regs_spi[] = {
++	[SPI_CMD]		= SPI_BCM_6338_SPI_CMD,
++	[SPI_INT_STATUS]	= SPI_BCM_6338_SPI_INT_STATUS,
++	[SPI_INT_MASK_ST]	= SPI_BCM_6338_SPI_MASK_INT_ST,
++	[SPI_INT_MASK]		= SPI_BCM_6338_SPI_INT_MASK,
++	[SPI_ST]		= SPI_BCM_6338_SPI_ST,
++	[SPI_CLK_CFG]		= SPI_BCM_6338_SPI_CLK_CFG,
++	[SPI_FILL_BYTE]		= SPI_BCM_6338_SPI_FILL_BYTE,
++	[SPI_MSG_TAIL]		= SPI_BCM_6338_SPI_MSG_TAIL,
++	[SPI_RX_TAIL]		= SPI_BCM_6338_SPI_RX_TAIL,
++	[SPI_MSG_CTL]		= SPI_BCM_6338_SPI_MSG_CTL,
++	[SPI_MSG_DATA]		= SPI_BCM_6338_SPI_MSG_DATA,
++	[SPI_RX_DATA]		= SPI_BCM_6338_SPI_RX_DATA,
++};
++
++static const unsigned long bcm96348_regs_spi[] = {
++	[SPI_CMD]		= SPI_BCM_6348_SPI_CMD,
++	[SPI_INT_STATUS]	= SPI_BCM_6348_SPI_INT_STATUS,
++	[SPI_INT_MASK_ST]	= SPI_BCM_6348_SPI_MASK_INT_ST,
++	[SPI_INT_MASK]		= SPI_BCM_6348_SPI_INT_MASK,
++	[SPI_ST]		= SPI_BCM_6348_SPI_ST,
++	[SPI_CLK_CFG]		= SPI_BCM_6348_SPI_CLK_CFG,
++	[SPI_FILL_BYTE]		= SPI_BCM_6348_SPI_FILL_BYTE,
++	[SPI_MSG_TAIL]		= SPI_BCM_6348_SPI_MSG_TAIL,
++	[SPI_RX_TAIL]		= SPI_BCM_6348_SPI_RX_TAIL,
++	[SPI_MSG_CTL]		= SPI_BCM_6348_SPI_MSG_CTL,
++	[SPI_MSG_DATA]		= SPI_BCM_6348_SPI_MSG_DATA,
++	[SPI_RX_DATA]		= SPI_BCM_6348_SPI_RX_DATA,
++};
++
++static const unsigned long bcm96358_regs_spi[] = {
++	[SPI_CMD]		= SPI_BCM_6358_SPI_CMD,
++	[SPI_INT_STATUS]	= SPI_BCM_6358_SPI_INT_STATUS,
++	[SPI_INT_MASK_ST]	= SPI_BCM_6358_SPI_MASK_INT_ST,
++	[SPI_INT_MASK]		= SPI_BCM_6358_SPI_INT_MASK,
++	[SPI_ST]		= SPI_BCM_6358_SPI_STATUS,
++	[SPI_CLK_CFG]		= SPI_BCM_6358_SPI_CLK_CFG,
++	[SPI_FILL_BYTE]		= SPI_BCM_6358_SPI_FILL_BYTE,
++	[SPI_MSG_TAIL]		= SPI_BCM_6358_SPI_MSG_TAIL,
++	[SPI_RX_TAIL]		= SPI_BCM_6358_SPI_RX_TAIL,
++	[SPI_MSG_CTL]		= SPI_BCM_6358_MSG_CTL,
++	[SPI_MSG_DATA]		= SPI_BCM_6358_SPI_MSG_DATA,
++	[SPI_RX_DATA]		= SPI_BCM_6358_SPI_RX_DATA,
++};
++
++const unsigned long *bcm63xx_regs_spi;
++EXPORT_SYMBOL(bcm63xx_regs_spi);
++
++static __init void bcm63xx_spi_regs_init(void)
++{
++	if (BCMCPU_IS_6338())
++		bcm63xx_regs_spi = bcm96338_regs_spi;
++	if (BCMCPU_IS_6348())
++		bcm63xx_regs_spi = bcm96348_regs_spi;
++	if (BCMCPU_IS_6358())
++		bcm63xx_regs_spi = bcm96358_regs_spi;
++}
++#else
++static __init void bcm63xx_spi_regs_init(void) { }
++#endif
++
++static struct resource spi_resources[] = {
++	{
++		.start		= -1, /* filled at runtime */
++		.end		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_MEM,
++	},
++	{
++		.start		= -1, /* filled at runtime */
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static struct bcm63xx_spi_pdata spi_pdata = {
++	.bus_num		= 0,
++	.num_chipselect		= 8,
++	.speed_hz		= 50000000,	/* Fclk */
++};
++
++static struct platform_device bcm63xx_spi_device = {
++	.name		= "bcm63xx-spi",
++	.id		= 0,
++	.num_resources	= ARRAY_SIZE(spi_resources),
++	.resource	= spi_resources,
++	.dev		= {
++		.platform_data = &spi_pdata,
++	},
++};
++
++int __init bcm63xx_spi_register(void)
++{
++	spi_resources[0].start = bcm63xx_regset_address(RSET_SPI);
++	spi_resources[0].end = spi_resources[0].start;
++	spi_resources[0].end += RSET_SPI_SIZE - 1;
++	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
++
++	/* Fill in platform data */
++	if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
++		spi_pdata.fifo_size = SPI_BCM_6338_SPI_MSG_DATA_SIZE;
++
++	if (BCMCPU_IS_6358())
++		spi_pdata.fifo_size = SPI_BCM_6358_SPI_MSG_DATA_SIZE;
++
++	bcm63xx_spi_regs_init();
++
++	return platform_device_register(&bcm63xx_spi_device);
++}
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
+@@ -109,6 +109,7 @@ enum bcm63xx_regs_set {
+ #define RSET_WDT_SIZE			12
+ #define RSET_ENET_SIZE			2048
+ #define RSET_ENETDMA_SIZE		2048
++#define RSET_SPI_SIZE			256
+ #define RSET_UART_SIZE			24
+ #define RSET_UDC_SIZE			256
+ #define RSET_OHCI_SIZE			256
+@@ -214,7 +215,7 @@ enum bcm63xx_regs_set {
+ #define BCM_6358_UART0_BASE		(0xfffe0100)
+ #define BCM_6358_UART1_BASE		(0xfffe0120)
+ #define BCM_6358_GPIO_BASE		(0xfffe0080)
+-#define BCM_6358_SPI_BASE		(0xdeadbeef)
++#define BCM_6358_SPI_BASE		(0xfffe0800)
+ #define BCM_6358_UDC0_BASE		(0xfffe0400)
+ #define BCM_6358_OHCI0_BASE		(0xfffe1400)
+ #define BCM_6358_OHCI_PRIV_BASE		(0xdeadbeef)
+@@ -441,6 +442,7 @@ static inline unsigned long bcm63xx_regs
+  */
+ enum bcm63xx_irq {
+ 	IRQ_TIMER = 0,
++	IRQ_SPI,
+ 	IRQ_UART0,
+ 	IRQ_UART1,
+ 	IRQ_DSL,
+@@ -507,6 +509,7 @@ enum bcm63xx_irq {
+  * 6348 irqs
+  */
+ #define BCM_6348_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
++#define BCM_6348_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
+ #define BCM_6348_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+ #define BCM_6348_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
+ #define BCM_6348_UDC0_IRQ		(IRQ_INTERNAL_BASE + 6)
+@@ -531,6 +534,7 @@ enum bcm63xx_irq {
+  * 6358 irqs
+  */
+ #define BCM_6358_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
++#define BCM_6358_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
+ #define BCM_6358_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+ #define BCM_6358_UART1_IRQ		(IRQ_INTERNAL_BASE + 3)
+ #define BCM_6358_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 5)
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -769,4 +769,116 @@
+ #define DMIPSPLLCFG_N2_SHIFT		29
+ #define DMIPSPLLCFG_N2_MASK		(0x7 << DMIPSPLLCFG_N2_SHIFT)
+ 
++/*************************************************************************
++ * _REG relative to RSET_SPI
++ *************************************************************************/
++
++/* BCM 6338 SPI core */
++#define SPI_BCM_6338_SPI_CMD		0x00	/* 16-bits register */
++#define SPI_BCM_6338_SPI_INT_STATUS	0x02
++#define SPI_BCM_6338_SPI_MASK_INT_ST	0x03
++#define SPI_BCM_6338_SPI_INT_MASK	0x04
++#define SPI_BCM_6338_SPI_ST		0x05
++#define SPI_BCM_6338_SPI_CLK_CFG	0x06
++#define SPI_BCM_6338_SPI_FILL_BYTE	0x07
++#define SPI_BCM_6338_SPI_MSG_TAIL	0x09
++#define SPI_BCM_6338_SPI_RX_TAIL	0x0b
++#define SPI_BCM_6338_SPI_MSG_CTL	0x40
++#define SPI_BCM_6338_SPI_MSG_DATA	0x41
++#define SPI_BCM_6338_SPI_MSG_DATA_SIZE	0x3f
++#define SPI_BCM_6338_SPI_RX_DATA	0x80
++#define SPI_BCM_6338_SPI_RX_DATA_SIZE	0x3f
++
++/* BCM 6348 SPI core */
++#define SPI_BCM_6348_SPI_MASK_INT_ST	0x00
++#define SPI_BCM_6348_SPI_INT_STATUS	0x01
++#define SPI_BCM_6348_SPI_CMD		0x02	/* 16-bits register */
++#define SPI_BCM_6348_SPI_FILL_BYTE	0x04
++#define SPI_BCM_6348_SPI_CLK_CFG	0x05
++#define SPI_BCM_6348_SPI_ST		0x06
++#define SPI_BCM_6348_SPI_INT_MASK	0x07
++#define SPI_BCM_6348_SPI_RX_TAIL	0x08
++#define SPI_BCM_6348_SPI_MSG_TAIL	0x10
++#define SPI_BCM_6348_SPI_MSG_DATA	0x40
++#define SPI_BCM_6348_SPI_MSG_CTL	0x42
++#define SPI_BCM_6348_SPI_MSG_DATA_SIZE	0x3f
++#define SPI_BCM_6348_SPI_RX_DATA	0x80
++#define SPI_BCM_6348_SPI_RX_DATA_SIZE	0x3f
++
++/* BCM 6358 SPI core */
++#define SPI_BCM_6358_MSG_CTL		0x00	/* 16-bits register */
++
++#define SPI_BCM_6358_SPI_MSG_DATA	0x02
++#define SPI_BCM_6358_SPI_MSG_DATA_SIZE	0x21e
++
++#define SPI_BCM_6358_SPI_RX_DATA	0x400
++#define SPI_BCM_6358_SPI_RX_DATA_SIZE	0x220
++
++#define SPI_BCM_6358_SPI_CMD		0x700	/* 16-bits register */
++
++#define SPI_BCM_6358_SPI_INT_STATUS	0x702
++#define SPI_BCM_6358_SPI_MASK_INT_ST	0x703
++
++#define SPI_BCM_6358_SPI_INT_MASK	0x704
++
++#define SPI_BCM_6358_SPI_STATUS		0x705
++
++#define SPI_BCM_6358_SPI_CLK_CFG	0x706
++
++#define SPI_BCM_6358_SPI_FILL_BYTE	0x707
++#define SPI_BCM_6358_SPI_MSG_TAIL	0x709
++#define SPI_BCM_6358_SPI_RX_TAIL	0x70B
++
++/* Shared SPI definitions */
++
++/* Message configuration */
++#define SPI_FD_RW			0x00
++#define SPI_HD_W			0x01
++#define SPI_HD_R			0x02
++#define SPI_BYTE_CNT_SHIFT		0
++#define SPI_MSG_TYPE_SHIFT		14
++
++/* Command */
++#define SPI_CMD_NOOP			0x01
++#define SPI_CMD_SOFT_RESET		0x02
++#define SPI_CMD_HARD_RESET		0x04
++#define SPI_CMD_START_IMMEDIATE		0x08
++#define SPI_CMD_COMMAND_SHIFT		0
++#define SPI_CMD_COMMAND_MASK		0x000f
++#define SPI_CMD_DEVICE_ID_SHIFT		4
++#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT	8
++#define SPI_CMD_ONE_BYTE_SHIFT		11
++#define SPI_CMD_ONE_WIRE_SHIFT		12
++#define SPI_DEV_ID_0			0
++#define SPI_DEV_ID_1			1
++#define SPI_DEV_ID_2			2
++#define SPI_DEV_ID_3			3
++
++/* Interrupt mask */
++#define SPI_INTR_CMD_DONE		0x01
++#define SPI_INTR_RX_OVERFLOW		0x02
++#define SPI_INTR_TX_UNDERFLOW		0x04
++#define SPI_INTR_TX_OVERFLOW		0x08
++#define SPI_INTR_RX_UNDERFLOW		0x10
++#define SPI_INTR_CLEAR_ALL		0x1f
++
++/* Status */
++#define SPI_RX_EMPTY			0x02
++#define SPI_CMD_BUSY			0x04
++#define SPI_SERIAL_BUSY			0x08
++
++/* Clock configuration */
++#define SPI_CLK_20MHZ			0x00
++#define SPI_CLK_0_391MHZ		0x01
++#define SPI_CLK_0_781MHZ		0x02 /* default */
++#define SPI_CLK_1_563MHZ		0x03
++#define SPI_CLK_3_125MHZ		0x04
++#define SPI_CLK_6_250MHZ		0x05
++#define SPI_CLK_12_50MHZ		0x06
++#define SPI_CLK_25MHZ			0x07
++#define SPI_CLK_MASK			0x07
++#define SPI_SSOFFTIME_MASK		0x38
++#define SPI_SSOFFTIME_SHIFT		3
++#define SPI_BYTE_SWAP			0x80
++
+ #endif /* BCM63XX_REGS_H_ */
+--- /dev/null
++++ b/drivers/spi/bcm63xx_spi.c
+@@ -0,0 +1,496 @@
++/*
++ * Broadcom BCM63xx SPI controller support
++ *
++ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
++ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version 2
++ * of the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the
++ * Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/clk.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/delay.h>
++#include <linux/interrupt.h>
++#include <linux/spi/spi.h>
++#include <linux/completion.h>
++#include <linux/err.h>
++
++#include <bcm63xx_dev_spi.h>
++
++#define PFX 		KBUILD_MODNAME
++#define DRV_VER		"0.1.2"
++
++struct bcm63xx_spi {
++	spinlock_t              lock;
++	int			stopping;
++        struct completion	done;
++
++	void __iomem		*regs;
++	int			irq;
++
++	/* Platform data */
++        u32			speed_hz;
++	unsigned		fifo_size;
++
++	/* Data buffers */
++	const unsigned char	*tx_ptr;
++	unsigned char		*rx_ptr;
++
++	/* data iomem */
++	u8 __iomem		*tx_io;
++	const u8 __iomem	*rx_io;
++
++	int			remaining_bytes;
++
++	struct clk		*clk;
++	struct platform_device	*pdev;
++};
++
++static inline u8 bcm_spi_readb(struct bcm63xx_spi *bs,
++				unsigned int offset)
++{
++	return bcm_readw(bs->regs + bcm63xx_spireg(offset));
++}
++
++static inline u16 bcm_spi_readw(struct bcm63xx_spi *bs,
++				unsigned int offset)
++{
++	return bcm_readw(bs->regs + bcm63xx_spireg(offset));
++}
++
++static inline void bcm_spi_writeb(struct bcm63xx_spi *bs,
++				  u8 value, unsigned int offset)
++{
++	bcm_writeb(value, bs->regs + bcm63xx_spireg(offset));
++}
++
++static inline void bcm_spi_writew(struct bcm63xx_spi *bs,
++				  u16 value, unsigned int offset)
++{
++	bcm_writew(value, bs->regs + bcm63xx_spireg(offset));
++}
++
++static int bcm63xx_spi_setup_transfer(struct spi_device *spi,
++				      struct spi_transfer *t)
++{
++	u8 bits_per_word;
++	u8 clk_cfg;
++	u32 hz;
++	unsigned int div;
++
++	struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
++
++	bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word;
++	hz = (t) ? t->speed_hz : spi->max_speed_hz;
++	if (bits_per_word != 8) {
++		dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
++			__func__, bits_per_word);
++		return -EINVAL;
++        }
++
++	if (spi->chip_select > spi->master->num_chipselect) {
++		dev_err(&spi->dev, "%s, unsupported slave %d\n",
++			__func__, spi->chip_select);
++		return -EINVAL;
++	}
++
++	/* Check clock setting */
++	div = (bs->speed_hz / hz);
++	switch (div) {
++	case 2:
++		clk_cfg = SPI_CLK_25MHZ;
++		break;
++	case 4:
++		clk_cfg = SPI_CLK_12_50MHZ;
++		break;
++	case 8:
++		clk_cfg = SPI_CLK_6_250MHZ;
++		break;
++	case 16:
++		clk_cfg = SPI_CLK_3_125MHZ;
++		break;
++	case 32:
++		clk_cfg = SPI_CLK_1_563MHZ;
++		break;
++	case 64:
++		clk_cfg = SPI_CLK_0_781MHZ;
++		break;
++	case 128:
++	default:
++		/* Set to slowest mode for compatibility */
++		clk_cfg = SPI_CLK_0_391MHZ;
++		break;
++	}
++
++	bcm_spi_writeb(bs, clk_cfg, SPI_CLK_CFG);
++	dev_dbg(&spi->dev, "Setting clock register to %d (hz %d, cmd %02x)\n",
++		div, hz, clk_cfg);
++
++	return 0;
++}
++
++/* the spi->mode bits understood by this driver: */
++#define MODEBITS (SPI_CPOL | SPI_CPHA)
++
++static int bcm63xx_spi_setup(struct spi_device *spi)
++{
++	struct bcm63xx_spi *bs;
++	int ret;
++
++	bs = spi_master_get_devdata(spi->master);
++
++	if (bs->stopping)
++		return -ESHUTDOWN;
++
++	if (!spi->bits_per_word)
++		spi->bits_per_word = 8;
++
++	if (spi->mode & ~MODEBITS) {
++		dev_err(&spi->dev, "%s, unsupported mode bits %x\n",
++			__func__, spi->mode & ~MODEBITS);
++		return -EINVAL;
++	}
++
++	ret = bcm63xx_spi_setup_transfer(spi, NULL);
++	if (ret < 0) {
++		dev_err(&spi->dev, "setup: unsupported mode bits %x\n",
++			spi->mode & ~MODEBITS);
++		return ret;
++	}
++
++	dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
++		__func__, spi->mode & MODEBITS, spi->bits_per_word, 0);
++
++	return 0;
++}
++
++/* Fill the TX FIFO with as many bytes as possible */
++static void bcm63xx_spi_fill_tx_fifo(struct bcm63xx_spi *bs)
++{
++	u8 size;
++
++        /* Fill the Tx FIFO with as many bytes as possible */
++	size = bs->remaining_bytes < bs->fifo_size ? bs->remaining_bytes :
++		bs->fifo_size;
++	memcpy_toio(bs->tx_io, bs->tx_ptr, size);
++	bs->remaining_bytes -= size;
++}
++
++static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
++{
++	struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
++	u16 msg_ctl;
++	u16 cmd;
++
++	dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
++		t->tx_buf, t->rx_buf, t->len);
++
++	/* Transmitter is inhibited */
++	bs->tx_ptr = t->tx_buf;
++	bs->rx_ptr = t->rx_buf;
++	init_completion(&bs->done);
++
++	if (t->tx_buf) {
++		bs->remaining_bytes = t->len;
++		bcm63xx_spi_fill_tx_fifo(bs);
++	}
++
++	/* Enable the command done interrupt which
++	 * we use to determine completion of a command */
++	bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
++
++	/* Fill in the Message control register */
++	msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT);
++
++	if (t->rx_buf && t->tx_buf)
++		msg_ctl |= (SPI_FD_RW << SPI_MSG_TYPE_SHIFT);
++	else if (t->rx_buf)
++		msg_ctl |= (SPI_HD_R << SPI_MSG_TYPE_SHIFT);
++	else if (t->tx_buf)
++		msg_ctl |= (SPI_HD_W << SPI_MSG_TYPE_SHIFT);
++
++	bcm_spi_writew(bs, msg_ctl, SPI_MSG_CTL);
++
++	/* Issue the transfer */
++	cmd = SPI_CMD_START_IMMEDIATE;
++	cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
++	cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT);
++	bcm_spi_writew(bs, cmd, SPI_CMD);
++	wait_for_completion(&bs->done);
++
++	/* Disable the CMD_DONE interrupt */
++	bcm_spi_writeb(bs, 0, SPI_INT_MASK);
++
++	return t->len - bs->remaining_bytes;
++}
++
++static int bcm63xx_transfer(struct spi_device *spi, struct spi_message *m)
++{
++	struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
++	struct spi_transfer *t;
++	int ret = 0;
++
++	if (unlikely(list_empty(&m->transfers)))
++		return -EINVAL;
++
++	if (bs->stopping)
++		return -ESHUTDOWN;
++
++	list_for_each_entry(t, &m->transfers, transfer_list) {
++		ret += bcm63xx_txrx_bufs(spi, t);
++	}
++
++	m->complete(m->context);
++
++	return ret;
++}
++
++/* This driver supports single master mode only. Hence
++ * CMD_DONE is the only interrupt we care about
++ */
++static irqreturn_t bcm63xx_spi_interrupt(int irq, void *dev_id)
++{
++	struct spi_master *master = (struct spi_master *)dev_id;
++	struct bcm63xx_spi *bs = spi_master_get_devdata(master);
++	u8 intr;
++	u16 cmd;
++
++	/* Read interupts and clear them immediately */
++	intr = bcm_spi_readb(bs, SPI_INT_STATUS);
++	bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
++	bcm_spi_writeb(bs, 0, SPI_INT_MASK);
++
++	/* A tansfer completed */
++	if (intr & SPI_INTR_CMD_DONE) {
++		u8 rx_tail;
++
++		rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
++
++		/* Read out all the data */
++		if (rx_tail)
++			memcpy_fromio(bs->rx_ptr, bs->rx_io, rx_tail);
++
++		/* See if there is more data to send */
++		if (bs->remaining_bytes > 0) {
++			bcm63xx_spi_fill_tx_fifo(bs);
++
++			/* Start the transfer */
++			bcm_spi_writew(bs, SPI_HD_W << SPI_MSG_TYPE_SHIFT,
++				       SPI_MSG_CTL);
++			cmd = bcm_spi_readw(bs, SPI_CMD);
++			cmd |= SPI_CMD_START_IMMEDIATE;
++			cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
++			bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
++			bcm_spi_writew(bs, cmd, SPI_CMD);
++		} else {
++			complete(&bs->done);
++		}
++	}
++
++	return IRQ_HANDLED;
++}
++
++
++static int __init bcm63xx_spi_probe(struct platform_device *pdev)
++{
++	struct resource *r;
++	struct device *dev = &pdev->dev;
++	struct bcm63xx_spi_pdata *pdata = pdev->dev.platform_data;
++	int irq;
++	struct spi_master *master;
++	struct clk *clk;
++	struct bcm63xx_spi *bs;
++	int ret;
++
++	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	if (!r) {
++		dev_err(dev, "no iomem\n");
++		ret = -ENXIO;
++		goto out;
++	}
++
++	irq = platform_get_irq(pdev, 0);
++	if (irq < 0) {
++		dev_err(dev, "no irq\n");
++		ret = -ENXIO;
++		goto out;
++	}
++
++	clk = clk_get(dev, "spi");
++	if (IS_ERR(clk)) {
++		dev_err(dev, "no clock for device\n");
++		ret = -ENODEV;
++		goto out;
++	}
++
++	master = spi_alloc_master(dev, sizeof(*bs));
++	if (!master) {
++		dev_err(dev, "out of memory\n");
++		ret = -ENOMEM;
++		goto out_free;
++	}
++
++	bs = spi_master_get_devdata(master);
++	init_completion(&bs->done);
++
++	platform_set_drvdata(pdev, master);
++	bs->pdev = pdev;
++
++	if (!request_mem_region(r->start, r->end - r->start, PFX)) {
++		dev_err(dev, "iomem request failed\n");
++		ret = -ENXIO;
++		goto out_put_master;
++	}
++
++	bs->regs = ioremap_nocache(r->start, r->end - r->start);
++	if (!bs->regs) {
++		dev_err(dev, "unable to ioremap regs\n");
++		ret = -ENOMEM;
++		goto out_put_master;
++	}
++	bs->irq = irq;
++	bs->clk = clk;
++	bs->fifo_size = pdata->fifo_size;
++
++	ret = request_irq(irq, bcm63xx_spi_interrupt, 0, pdev->name, master);
++	if (ret) {
++		dev_err(dev, "unable to request irq\n");
++		goto out_unmap;
++	}
++
++	master->bus_num = pdata->bus_num;
++	master->num_chipselect = pdata->num_chipselect;
++	master->setup = bcm63xx_spi_setup;
++	master->transfer = bcm63xx_transfer;
++	bs->speed_hz = pdata->speed_hz;
++	bs->stopping = 0;
++	bs->tx_io = (u8*)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA));
++	bs->rx_io = (const u8*)(bs->regs + bcm63xx_spireg(SPI_RX_DATA));
++	spin_lock_init(&bs->lock);
++
++	/* Initialize hardware */
++	clk_enable(bs->clk);
++	bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
++
++	/* register and we are done */
++	ret = spi_register_master(master);
++	if (ret) {
++		dev_err(dev, "spi register failed\n");
++		goto out_reset_hw;
++	}
++
++	dev_info(dev, "at 0x%08x (irq %d, FIFOs size %d) v%s\n",
++		 r->start, irq, bs->fifo_size, DRV_VER);
++
++	return 0;
++
++out_reset_hw:
++	clk_disable(clk);
++	free_irq(irq, master);
++out_unmap:
++	iounmap(bs->regs);
++out_put_master:
++	spi_master_put(master);
++out_free:
++	clk_put(clk);
++out:
++	return ret;
++}
++
++static int __exit bcm63xx_spi_remove(struct platform_device *pdev)
++{
++	struct spi_master	*master = platform_get_drvdata(pdev);
++	struct bcm63xx_spi	*bs = spi_master_get_devdata(master);
++	struct resource		*r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++
++	/* reset spi block */
++	bcm_spi_writeb(bs, 0, SPI_INT_MASK);
++	spin_lock(&bs->lock);
++	bs->stopping = 1;
++
++	/* HW shutdown */
++	clk_disable(bs->clk);
++	clk_put(bs->clk);
++
++	spin_unlock(&bs->lock);
++
++	free_irq(bs->irq, master);
++	iounmap(bs->regs);
++	release_mem_region(r->start, r->end - r->start);
++	platform_set_drvdata(pdev, 0);
++	spi_unregister_master(master);
++
++	return 0;
++}
++
++#ifdef CONFIG_PM
++static int bcm63xx_spi_suspend(struct platform_device *pdev, pm_message_t mesg)
++{
++	struct spi_master	*master = platform_get_drvdata(pdev);
++	struct bcm63xx_spi	*bs = spi_master_get_devdata(master);
++
++        clk_disable(bs->clk);
++
++	return 0;
++}
++
++static int bcm63xx_spi_resume(struct platform_device *pdev)
++{
++	struct spi_master	*master = platform_get_drvdata(pdev);
++	struct bcm63xx_spi	*bs = spi_master_get_devdata(master);
++
++	clk_enable(bs->clk);
++
++	return 0;
++}
++#else
++#define bcm63xx_spi_suspend	NULL
++#define bcm63xx_spi_resume	NULL
++#endif
++
++static struct platform_driver bcm63xx_spi_driver = {
++	.driver = {
++		.name	= "bcm63xx-spi",
++		.owner	= THIS_MODULE,
++	},
++	.probe		= bcm63xx_spi_probe,
++	.remove		= __exit_p(bcm63xx_spi_remove),
++	.suspend	= bcm63xx_spi_suspend,
++	.resume		= bcm63xx_spi_resume,
++};
++
++
++static int __init bcm63xx_spi_init(void)
++{
++	return platform_driver_register(&bcm63xx_spi_driver);
++}
++
++static void __exit bcm63xx_spi_exit(void)
++{
++	platform_driver_unregister(&bcm63xx_spi_driver);
++}
++
++module_init(bcm63xx_spi_init);
++module_exit(bcm63xx_spi_exit);
++
++MODULE_ALIAS("platform:bcm63xx_spi");
++MODULE_AUTHOR("Florian Fainelli <florian@openwrt.org>");
++MODULE_AUTHOR("Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>");
++MODULE_DESCRIPTION("Broadcom BCM63xx SPI Controller driver");
++MODULE_LICENSE("GPL");
++MODULE_VERSION(DRV_VER);
+--- a/drivers/spi/Kconfig
++++ b/drivers/spi/Kconfig
+@@ -60,6 +60,12 @@ config SPI_ATMEL
+ 	  This selects a driver for the Atmel SPI Controller, present on
+ 	  many AT32 (AVR32) and AT91 (ARM) chips.
+ 
++config SPI_BCM63XX
++	tristate "Broadcom BCM63xx SPI controller"
++	depends on BCM63XX
++	help
++	  This is the SPI controller master driver for Broadcom BCM63xx SoC.
++
+ config SPI_BFIN
+ 	tristate "SPI controller driver for ADI Blackfin5xx"
+ 	depends on BLACKFIN
+--- a/drivers/spi/Makefile
++++ b/drivers/spi/Makefile
+@@ -50,6 +50,7 @@ obj-$(CONFIG_SPI_SH_SCI)		+= spi_sh_sci.
+ obj-$(CONFIG_SPI_SH_MSIOF)		+= spi_sh_msiof.o
+ obj-$(CONFIG_SPI_STMP3XXX)		+= spi_stmp.o
+ obj-$(CONFIG_SPI_NUC900)		+= spi_nuc900.o
++obj-$(CONFIG_SPI_BCM63XX)		+= bcm63xx_spi.o
+ 
+ # special build for s3c24xx spi driver with fiq support
+ spi_s3c24xx_hw-y			:= spi_s3c24xx.o
+--- /dev/null
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
+@@ -0,0 +1,126 @@
++#ifndef BCM63XX_DEV_SPI_H
++#define BCM63XX_DEV_SPI_H
++
++#include <linux/types.h>
++#include <bcm63xx_io.h>
++#include <bcm63xx_regs.h>
++
++int __init bcm63xx_spi_register(void);
++
++struct bcm63xx_spi_pdata {
++	unsigned int	fifo_size;
++	int		bus_num;
++	int		num_chipselect;
++	u32		speed_hz;
++};
++
++enum bcm63xx_regs_spi {
++        SPI_CMD,
++        SPI_INT_STATUS,
++        SPI_INT_MASK_ST,
++        SPI_INT_MASK,
++        SPI_ST,
++        SPI_CLK_CFG,
++        SPI_FILL_BYTE,
++        SPI_MSG_TAIL,
++        SPI_RX_TAIL,
++        SPI_MSG_CTL,
++        SPI_MSG_DATA,
++        SPI_RX_DATA,
++};
++
++static inline unsigned long bcm63xx_spireg(enum bcm63xx_regs_spi reg)
++{
++#ifdef BCMCPU_RUNTIME_DETECT
++	extern const unsigned long *bcm63xx_regs_spi;
++        return bcm63xx_regs_spi[reg];
++#else
++#ifdef CONFIG_BCM63XX_CPU_6338
++switch (reg) {
++	case SPI_CMD:
++		return SPI_BCM_6338_SPI_CMD;
++	case SPI_INT_STATUS:
++		return SPI_BCM_6338_SPI_INT_STATUS;
++	case SPI_INT_MASK_ST:
++		return SPI_BCM_6338_SPI_MASK_INT_ST;
++	case SPI_INT_MASK:
++		return SPI_BCM_6338_SPI_INT_MASK;
++	case SPI_ST:
++		return SPI_BCM_6338_SPI_ST;
++	case SPI_CLK_CFG:
++		return SPI_BCM_6338_SPI_CLK_CFG;
++	case SPI_FILL_BYTE:
++		return SPI_BCM_6338_SPI_FILL_BYTE;
++	case SPI_MSG_TAIL:
++		return SPI_BCM_6338_SPI_MSG_TAIL;
++	case SPI_RX_TAIL:
++		return SPI_BCM_6338_SPI_RX_TAIL;
++	case SPI_MSG_CTL:
++		return SPI_BCM_6338_SPI_MSG_CTL;
++	case SPI_MSG_DATA:
++		return SPI_BCM_6338_SPI_MSG_DATA;
++	case SPI_RX_DATA:
++		return SPI_BCM_6338_SPI_RX_DATA;
++}
++#endif
++#ifdef CONFIG_BCM63XX_CPU_6348
++switch (reg) {
++	case SPI_CMD:
++		return SPI_BCM_6348_SPI_CMD;
++	case SPI_INT_MASK_ST:
++		return SPI_BCM_6348_SPI_MASK_INT_ST;
++	case SPI_INT_MASK:
++		return SPI_BCM_6348_SPI_INT_MASK;
++	case SPI_INT_STATUS:
++		return SPI_BCM_6348_SPI_INT_STATUS;
++	case SPI_ST:
++		return SPI_BCM_6348_SPI_ST;
++	case SPI_CLK_CFG:
++		return SPI_BCM_6348_SPI_CLK_CFG;
++	case SPI_FILL_BYTE:
++		return SPI_BCM_6348_SPI_FILL_BYTE;
++	case SPI_MSG_TAIL:
++		return SPI_BCM_6348_SPI_MSG_TAIL;
++	case SPI_RX_TAIL:
++		return SPI_BCM_6348_SPI_RX_TAIL;
++	case SPI_MSG_CTL:
++		return SPI_BCM_6348_SPI_MSG_CTL;
++	case SPI_MSG_DATA:
++		return SPI_BCM_6348_SPI_MSG_DATA;
++	case SPI_RX_DATA:
++		return SPI_BCM_6348_SPI_RX_DATA;
++}
++#endif
++#ifdef CONFIG_BCM63XX_CPU_6358
++switch (reg) {
++	case SPI_CMD:
++		return SPI_BCM_6358_SPI_CMD;
++	case SPI_INT_STATUS:
++		return SPI_BCM_6358_SPI_INT_STATUS;
++	case SPI_INT_MASK_ST:
++		return SPI_BCM_6358_SPI_MASK_INT_ST;
++	case SPI_INT_MASK:
++		return SPI_BCM_6358_SPI_INT_MASK;
++	case SPI_ST:
++		return SPI_BCM_6358_SPI_STATUS;
++	case SPI_CLK_CFG:
++		return SPI_BCM_6358_SPI_CLK_CFG;
++	case SPI_FILL_BYTE:
++		return SPI_BCM_6358_SPI_FILL_BYTE;
++	case SPI_MSG_TAIL:
++		return SPI_BCM_6358_SPI_MSG_TAIL;
++	case SPI_RX_TAIL:
++		return SPI_BCM_6358_SPI_RX_TAIL;
++	case SPI_MSG_CTL:
++		return SPI_BCM_6358_MSG_CTL;
++	case SPI_MSG_DATA:
++		return SPI_BCM_6358_SPI_MSG_DATA;
++	case SPI_RX_DATA:
++		return SPI_BCM_6358_SPI_RX_DATA;
++}
++#endif
++#endif
++	return 0;
++}
++
++#endif /* BCM63XX_DEV_SPI_H */
+--- a/arch/mips/bcm63xx/Makefile
++++ b/arch/mips/bcm63xx/Makefile
+@@ -1,6 +1,6 @@
+ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
+ 		   dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
+-		   dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o
++		   dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o dev-spi.o
+ obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+ 
+ obj-y		+= boards/
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -33,6 +33,7 @@
+ #include <bcm63xx_dev_usb_ohci.h>
+ #include <bcm63xx_dev_usb_ehci.h>
+ #include <bcm63xx_dev_usb_udc.h>
++#include <bcm63xx_dev_spi.h>
+ #include <board_bcm963xx.h>
+ 
+ #define PFX	"board_bcm963xx: "
+@@ -1586,6 +1587,9 @@ int __init board_register_devices(void)
+ 	if (board.num_spis)
+ 		spi_register_board_info(board.spis, board.num_spis);
+ 
++	if (!BCMCPU_IS_6345())
++		bcm63xx_spi_register();
++
+ 	/* read base address of boot chip select (0) */
+ 	if (BCMCPU_IS_6345())
+ 		val = 0x1fc00000;
diff --git a/target/linux/brcm63xx/patches-2.6.37/250-6358-enet1-external-mii-clk.patch b/target/linux/brcm63xx/patches-2.6.37/250-6358-enet1-external-mii-clk.patch
new file mode 100644
index 0000000..3e033fb
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/250-6358-enet1-external-mii-clk.patch
@@ -0,0 +1,22 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1477,6 +1477,8 @@ void __init board_prom_init(void)
+ 		if (BCMCPU_IS_6348())
+ 			val |= GPIO_MODE_6348_G3_EXT_MII |
+ 				GPIO_MODE_6348_G0_EXT_MII;
++		else if (BCMCPU_IS_6358())
++			val |= GPIO_MODE_6358_ENET1_MII_CLK_INV;
+ 	}
+ 
+ 	bcm_gpio_writel(val, GPIO_MODE_REG);
+--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+@@ -402,6 +402,8 @@
+ #define GPIO_MODE_6358_EXTRA_SPI_SS	(1 << 7)
+ #define GPIO_MODE_6358_SERIAL_LED	(1 << 10)
+ #define GPIO_MODE_6358_UTOPIA		(1 << 12)
++#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 30)
++#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 31)
+ 
+ 
+ /*************************************************************************
diff --git a/target/linux/brcm63xx/patches-2.6.37/260-no_ehci_over_current_check.patch b/target/linux/brcm63xx/patches-2.6.37/260-no_ehci_over_current_check.patch
new file mode 100644
index 0000000..816343e
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/260-no_ehci_over_current_check.patch
@@ -0,0 +1,16 @@
+--- a/drivers/usb/host/ehci-hub.c
++++ b/drivers/usb/host/ehci-hub.c
+@@ -861,11 +861,13 @@ static int ehci_hub_control (
+ 			 * power switching; they're allowed to just limit the
+ 			 * current.  khubd will turn the power back on.
+ 			 */
++#ifndef CONFIG_BCM63XX
+ 			if (HCS_PPC (ehci->hcs_params)){
+ 				ehci_writel(ehci,
+ 					temp & ~(PORT_RWC_BITS | PORT_POWER),
+ 					status_reg);
+ 			}
++#endif
+ 		}
+ 
+ 		/* whoever resumes must GetPortStatus to complete it!! */
diff --git a/target/linux/brcm63xx/patches-2.6.37/270-board-96338W2_E7T.patch b/target/linux/brcm63xx/patches-2.6.37/270-board-96338W2_E7T.patch
new file mode 100644
index 0000000..c6bd1c8
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/270-board-96338W2_E7T.patch
@@ -0,0 +1,49 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -135,6 +135,38 @@ static struct board_info __initdata boar
+ 		},
+ 	},
+ };
++
++static struct board_info __initdata board_96338w2_e7t = {
++	.name				= "96338W2_E7T",
++	.expected_cpu_id		= 0x6338,
++
++	.has_enet0			= 1,
++
++	.enet0 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++		.leds = {
++		{
++			.name		= "ppp",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "ppp-fail",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -1264,6 +1296,7 @@ static const struct board_info __initdat
+ #ifdef CONFIG_BCM63XX_CPU_6338
+ 	&board_96338gw,
+ 	&board_96338w,
++	&board_96338w2_e7t,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6345
+ 	&board_96345gw2,
diff --git a/target/linux/brcm63xx/patches-2.6.37/300-wl_exports.patch b/target/linux/brcm63xx/patches-2.6.37/300-wl_exports.patch
new file mode 100644
index 0000000..aa7322d
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/300-wl_exports.patch
@@ -0,0 +1,34 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -49,6 +49,13 @@ static unsigned int mac_addr_used;
+ static struct board_info board;
+ 
+ /*
++ * Required export for WL
++ */
++#define NVRAM_SPACE 0x8000
++char nvram_buf[NVRAM_SPACE];
++EXPORT_SYMBOL(nvram_buf);
++
++/*
+  * known 6338 boards
+  */
+ #ifdef CONFIG_BCM63XX_CPU_6338
+@@ -1444,6 +1451,7 @@ void __init board_prom_init(void)
+ 
+ 	/* extract nvram data */
+ 	memcpy(&nvram, boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
++	memcpy(&nvram_buf, boot_addr + BCM963XX_NVRAM_OFFSET, NVRAM_SPACE);
+ 
+ 	/* check checksum before using data */
+ 	if (nvram.version <= 4)
+--- a/arch/mips/mm/cache.c
++++ b/arch/mips/mm/cache.c
+@@ -52,6 +52,7 @@ void (*_dma_cache_wback)(unsigned long s
+ void (*_dma_cache_inv)(unsigned long start, unsigned long size);
+ 
+ EXPORT_SYMBOL(_dma_cache_wback_inv);
++EXPORT_SYMBOL(_dma_cache_inv);
+ 
+ #endif /* CONFIG_DMA_NONCOHERENT */
+ 
diff --git a/target/linux/brcm63xx/patches-2.6.37/310-CPVA642_board.patch b/target/linux/brcm63xx/patches-2.6.37/310-CPVA642_board.patch
new file mode 100644
index 0000000..480e190
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/310-CPVA642_board.patch
@@ -0,0 +1,109 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -662,6 +662,98 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_CPVA642 = {
++	.name                           = "CPVA642",
++	.expected_cpu_id                = 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet1                      = 1,
++	.has_pci                        = 1,
++
++	.enet1 = {
++		.force_speed_100        = 1,
++		.force_duplex_full      = 1,
++ 	},
++
++	.has_ohci0 = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++	    /* bi-color */
++		{
++			.name		= "power:red",
++			.gpio		= 14,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power:green",
++			.gpio		= 11,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "wifi:red",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi:green",
++			.gpio		= 28,
++			.active_low	= 0,
++		},
++		{
++			.name		= "link:red",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "link:green",
++			.gpio		= 10,
++			.active_low	= 1,
++		},
++		/* green only */
++		{
++			.name		= "ether",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "phone1",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "phone2",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "usb",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++    },
++
++	.buttons = {
++		{
++			.desc           = "reset",
++			.gpio           = 36,
++			.active_low     = 1,
++			.type           = EV_KEY,
++			.code           = KEY_RESTART,
++			.threshold      = 3,
++		},
++		{
++			.desc		= "wps",
++			.gpio		= 37,
++			.type		= EV_KEY,
++			.code		= KEY_WPS_BUTTON,
++			.threshold	= 3,
++		},
++	},
++};
++
++
+ static struct board_info __initdata board_AGPFS0 = {
+ 	.name                           = "AGPF-S0",
+ 	.expected_cpu_id                = 0x6358,
+@@ -1324,6 +1416,7 @@ static const struct board_info __initdat
+ 	&board_96358vw,
+ 	&board_96358vw2,
+ 	&board_AGPFS0,
++	&board_CPVA642,
+ 	&board_DWVS0,
+ 	&board_nb4_ser_r0,
+ 	&board_nb4_ser_r1,
diff --git a/target/linux/brcm63xx/patches-2.6.37/400-board_96358gw.patch b/target/linux/brcm63xx/patches-2.6.37/400-board_96358gw.patch
new file mode 100644
index 0000000..d008e1d
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/400-board_96358gw.patch
@@ -0,0 +1,70 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -562,6 +562,59 @@ static struct board_info __initdata boar
+  * known 6358 boards
+  */
+ #ifdef CONFIG_BCM63XX_CPU_6358
++
++static struct board_info __initdata board_96358gw = {
++	.name				= "96358GW",
++	.expected_cpu_id		= 0x6358,
++
++	.has_uart0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "power:green",
++			.gpio		= 5,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "power:red",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "adsl",
++			.gpio		= 9,
++			.active_low	= 1,
++		},
++		{
++			.name		= "internet:green",
++			.gpio		= 2,
++		},
++		{
++			.name		= "internet:red",
++			.gpio		= 10,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 34,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++	},
++};
++
+ static struct board_info __initdata board_96358vw = {
+ 	.name				= "96358VW",
+ 	.expected_cpu_id		= 0x6358,
+@@ -1413,6 +1466,7 @@ static const struct board_info __initdat
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358
++	&board_96358gw,
+ 	&board_96358vw,
+ 	&board_96358vw2,
+ 	&board_AGPFS0,
diff --git a/target/linux/brcm63xx/patches-2.6.37/410-boardid_fixup.patch b/target/linux/brcm63xx/patches-2.6.37/410-boardid_fixup.patch
new file mode 100644
index 0000000..286d9ac
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/410-boardid_fixup.patch
@@ -0,0 +1,62 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -35,6 +35,7 @@
+ #include <bcm63xx_dev_usb_udc.h>
+ #include <bcm63xx_dev_spi.h>
+ #include <board_bcm963xx.h>
++#include <bcm_tag.h>
+ 
+ #define PFX	"board_bcm963xx: "
+ 
+@@ -44,6 +45,9 @@
+ #define NB4_SPI_GPIO_CLK	6
+ #define NB4_74HC64_GPIO(X)	(NB4_74X164_GPIO_BASE + (X))
+ 
++#define CFE_OFFSET_64K		0x10000
++#define CFE_OFFSET_128K		0x20000
++
+ static struct bcm963xx_nvram nvram;
+ static unsigned int mac_addr_used;
+ static struct board_info board;
+@@ -1566,6 +1570,29 @@ static int board_get_mac_address(u8 *mac
+ 	return 0;
+ }
+ 
++static void __init boardid_fixup(u8 *boot_addr)
++{
++	struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
++
++	/* check if bcm_tag is at 64k offset */
++	if (strncmp(nvram.name, tag->boardid, BOARDID_LEN) != 0) {
++		/* else try 128k */
++		tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K);
++		if (strncmp(nvram.name, tag->boardid, BOARDID_LEN) != 0) {
++			/* No tag found */
++			printk(KERN_DEBUG "No bcm_tag found!\n");
++			return;
++		}
++	}
++	/* check if we should override the boardid */
++	if (tag->information1[0] != '+')
++		return;
++
++	strncpy(nvram.name, &tag->information1[1], BOARDID_LEN);
++
++	printk(KERN_INFO "Overriding boardid with '%s'\n", nvram.name);
++}
++
+ /*
+  * early init callback, read nvram data from flash and checksum it
+  */
+@@ -1617,6 +1644,11 @@ void __init board_prom_init(void)
+ 	/* Fixup broken nb4 board name */
+ 	nb4_nvram_fixup();
+ 
++	if (strcmp(cfe_version, "unknown") != 0) {
++		/* cfe present */
++		boardid_fixup(boot_addr);
++	}
++
+ 	/* find board by name */
+ 	for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
+ 		if (strncmp(nvram.name, bcm963xx_boards[i]->name,
diff --git a/target/linux/brcm63xx/patches-2.6.37/420-board_spw500v.patch b/target/linux/brcm63xx/patches-2.6.37/420-board_spw500v.patch
new file mode 100644
index 0000000..4f02951
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/420-board_spw500v.patch
@@ -0,0 +1,78 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -560,6 +560,67 @@ static struct board_info __initdata boar
+ 
+ };
+ 
++static struct board_info __initdata board_spw500v = {
++	.name				= "SPW500V",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++
++	.has_dsp			= 1,
++	.dsp = {
++		.gpio_rst		= 6,
++		.gpio_int		= 34,
++		.ext_irq		= 2,
++		.cs			= 2,
++	},
++
++	.leds = {
++		{
++			.name		= "power:red",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power:green",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "ppp",
++			.gpio		= 3,
++			.active_low	= 1,
++		},
++		{	.name		= "pstn",
++			.gpio		= 28,
++			.active_low	= 1,
++		},
++		{
++			.name		= "voip",
++			.gpio		= 32,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++	},
++};
++
+ #endif
+ 
+ /*
+@@ -1467,6 +1528,7 @@ static const struct board_info __initdat
+ 	&board_96348gw_a,
+ 	&board_rta1025w_16,
+ 	&board_96348_D4PW,
++	&board_spw500v,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/430-board_gw6200_gw6000.patch b/target/linux/brcm63xx/patches-2.6.37/430-board_gw6200_gw6000.patch
new file mode 100644
index 0000000..2e2398e
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/430-board_gw6200_gw6000.patch
@@ -0,0 +1,129 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -432,6 +432,117 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_gw6200 = {
++	.name				= "GW6200",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0 = 1,
++
++	.has_dsp			= 1,
++		.dsp = {
++        .gpio_rst		= 8, /* FIXME: What is real GPIO here? */
++		.gpio_int		= 34,
++		.ext_irq		= 2,
++		.cs			= 2,
++	},
++
++	.leds = {
++		{
++			.name		= "line1",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "line2",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "line3",
++			.gpio		= 6,
++			.active_low	= 1,
++		},
++		{
++			.name		= "tel",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++		    .name		= "ethernet",
++		    .gpio		= 35,
++		    .active_low	= 1,
++		}, 
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 36,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++	},
++};
++
++static struct board_info __initdata board_gw6000 = {
++	.name				= "GW6000",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0 = 1,
++
++	.has_dsp			= 1,
++	.dsp = {
++		.gpio_rst		= 6,
++		.gpio_int		= 34,
++		.ext_irq		= 2,
++		.cs			= 2,
++	},
++
++	/* GW6000 has no GPIO-controlled leds */
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 36,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++	},
++};
++
++
++
+ static struct board_info __initdata board_FAST2404 = {
+ 	.name				= "F@ST2404",
+ 	.expected_cpu_id		= 0x6348,
+@@ -1521,6 +1632,8 @@ static const struct board_info __initdat
+ #ifdef CONFIG_BCM63XX_CPU_6348
+ 	&board_96348r,
+ 	&board_96348gw,
++	&board_gw6000,
++	&board_gw6200,
+ 	&board_96348gw_10,
+ 	&board_96348gw_11,
+ 	&board_FAST2404,
diff --git a/target/linux/brcm63xx/patches-2.6.37/440-new_96348gw-11_leds.patch b/target/linux/brcm63xx/patches-2.6.37/440-new_96348gw-11_leds.patch
new file mode 100644
index 0000000..e1b6342
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/440-new_96348gw-11_leds.patch
@@ -0,0 +1,60 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -364,6 +364,49 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_ct536_ct5621 = {
++	.name				= "CT536_CT5621",
++	.expected_cpu_id		= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 0,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet1 = {
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0 = 1,
++	.has_pccard = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		{
++			.name		= "adsl-fail",
++			.gpio		= 2,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++	},
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 33,
++			.active_low	= 1,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.threshold	= 3,
++		},
++	},
++};
++
+ static struct board_info __initdata board_96348gw = {
+ 	.name				= "96348GW",
+ 	.expected_cpu_id		= 0x6348,
+@@ -1642,6 +1685,7 @@ static const struct board_info __initdat
+ 	&board_rta1025w_16,
+ 	&board_96348_D4PW,
+ 	&board_spw500v,
++	&board_ct536_ct5621,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/450-board-MAGIC.patch b/target/linux/brcm63xx/patches-2.6.37/450-board-MAGIC.patch
new file mode 100644
index 0000000..c192e53
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/450-board-MAGIC.patch
@@ -0,0 +1,87 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -775,6 +775,76 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_96348sv = {
++	.name				= "MAGIC",
++	.expected_cpu_id	= 0x6348,
++
++	.has_uart0			= 1,
++	.has_enet0			= 1,
++	.has_enet1			= 1,
++	.has_pci			= 1,
++
++	.enet0 = {
++		.has_phy			= 1,
++		.use_internal_phy	= 1,
++	},
++	.enet1 = {
++		/* is has BP_ENET_EXTERNAL_PHY */
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.has_ohci0			= 1,
++	.has_pccard			= 1,
++	.has_ehci0			= 1,
++
++	.has_dsp			= 1,
++	.dsp = {
++		.gpio_rst		= 25,
++		.gpio_int		= 34,
++		.cs				= 2,
++		.ext_irq		= 2,
++	},
++
++	.leds = {
++		{
++			.name		= "voip",
++			.gpio		= 22,
++			.active_low	= 1,
++		},
++		{
++			.name		= "adsl",
++			.gpio		= 5,
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi",
++			.gpio		= 28,
++		},
++		{
++			.name		= "usb",
++			.gpio		= 35,
++			.active_low	= 1,
++		},
++		{
++			.name		= "hpna",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power",
++			.gpio		= 0,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++		{
++			.name		= "stop",
++			.gpio		= 1,
++			.active_low	= 1,
++		},
++	},
++};
++
+ #endif
+ 
+ /*
+@@ -1686,6 +1756,7 @@ static const struct board_info __initdat
+ 	&board_96348_D4PW,
+ 	&board_spw500v,
+ 	&board_ct536_ct5621,
++	&board_96348sv,
+ #endif
+ 
+ #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/451-board_hw553.patch b/target/linux/brcm63xx/patches-2.6.37/451-board_hw553.patch
new file mode 100644
index 0000000..6a288c3
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/451-board_hw553.patch
@@ -0,0 +1,90 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1730,6 +1730,79 @@ static struct board_info __initdata boar
+ };
+ #endif
+ 
++static struct board_info __initdata board_HW553 = {
++	.name                           = "HW553",
++	.expected_cpu_id                = 0x6358,
++
++	.has_enet0                      = 1,
++	.has_enet1                      = 1,
++	.has_pci                        = 1,
++
++	.enet0 = {
++		.has_phy                = 1,
++		.use_internal_phy       = 1,
++	},
++
++	.enet1 = {
++		.force_speed_100        = 1,
++		.force_duplex_full      = 1,
++	},
++
++	.has_ohci0 = 1,
++	.has_ehci0 = 1,
++
++	.leds = {
++		/*Each led on HW553 is bi-color (except wifi) */		
++		{
++			.name		= "lan:red",
++			.gpio		= 34,
++			.active_low	= 1,
++		},
++		{
++			.name		= "lan:blue",
++			.gpio		= 35,
++			.active_low	= 1,
++		},
++		{
++			.name		= "adsl:red",
++			.gpio		= 22,
++			.active_low	= 1,
++		},
++		{
++			.name		= "adsl:blue",
++			.gpio		= 23,
++			.active_low	= 1,
++		},
++		{
++			.name		= "power:red",
++			.gpio		= 5,
++			.active_low	= 1,
++			.default_trigger = "default-on",
++		},
++
++		{
++			.name		= "power:blue",
++			.gpio		= 4,
++			.active_low	= 1,
++		},
++		{
++			.name		= "wifi:red",
++			.gpio		= 25,
++			.active_low	= 1,
++		},
++		{
++			.name		= "internetkey:red",
++			.gpio		= 12,
++			.active_low	= 1,
++		},
++		{
++			.name		= "internetkey:blue",
++			.gpio		= 13,
++			.active_low	= 1,
++		},
++	},
++};
++
+ /*
+  * all boards
+  */
+@@ -1771,6 +1844,7 @@ static const struct board_info __initdat
+ 	&board_nb4_ser_r2,
+ 	&board_nb4_fxc_r1,
+ 	&board_nb4_fxc_r2,
++	&board_HW553,
+ #endif
+ };
+ 
diff --git a/target/linux/brcm63xx/patches-2.6.37/977-ssb_export_fallback_sprom.patch b/target/linux/brcm63xx/patches-2.6.37/977-ssb_export_fallback_sprom.patch
new file mode 100644
index 0000000..2a22a3a
--- /dev/null
+++ b/target/linux/brcm63xx/patches-2.6.37/977-ssb_export_fallback_sprom.patch
@@ -0,0 +1,20 @@
+--- a/drivers/ssb/sprom.c
++++ b/drivers/ssb/sprom.c
+@@ -176,6 +176,7 @@ const struct ssb_sprom *ssb_get_fallback
+ {
+ 	return fallback_sprom;
+ }
++EXPORT_SYMBOL(ssb_get_fallback_sprom);
+ 
+ /* http://bcm-v4.sipsolutions.net/802.11/IsSpromAvailable */
+ bool ssb_is_sprom_available(struct ssb_bus *bus)
+--- a/include/linux/ssb/ssb.h
++++ b/include/linux/ssb/ssb.h
+@@ -401,6 +401,7 @@ extern bool ssb_is_sprom_available(struc
+ /* Set a fallback SPROM.
+  * See kdoc at the function definition for complete documentation. */
+ extern int ssb_arch_set_fallback_sprom(const struct ssb_sprom *sprom);
++extern const struct ssb_sprom *ssb_get_fallback_sprom(void);
+ 
+ /* Suspend a SSB bus.
+  * Call this from the parent bus suspend routine. */