move etrax generic files to specific kernel version

SVN-Revision: 15173

3 files changed, 0 insertions, 5459 deletions

diff --git a/target/linux/etrax/files/drivers/usb/host/hc-cris-dbg.h b/target/linux/etrax/files/drivers/usb/host/hc-cris-dbg.h
deleted file mode 100644
index f53f558..0000000
--- a/target/linux/etrax/files/drivers/usb/host/hc-cris-dbg.h
+++ /dev/null
@@ -1,141 +0,0 @@
-
-/* macros for debug output */
-
-#define hcd_dbg(hcd, fmt, args...) \
-	dev_info(hcd->self.controller, fmt, ## args)
-#define hcd_err(hcd, fmt, args...) \
-	dev_err(hcd->self.controller, fmt, ## args)
-#define hcd_info(hcd, fmt, args...) \
-	dev_info(hcd->self.controller, fmt, ## args)
-#define hcd_warn(hcd, fmt, args...) \
-	dev_warn(hcd->self.controller, fmt, ## args)
-
-/*
-#define devdrv_dbg(fmt, args...) \
-        printk(KERN_INFO "usb_devdrv dbg: ");printk(fmt, ## args)
-*/
-#define devdrv_dbg(fmt, args...) {}
-
-#define devdrv_err(fmt, args...) \
-        printk(KERN_ERR "usb_devdrv error: ");printk(fmt, ## args)
-#define devdrv_info(fmt, args...) \
-        printk(KERN_INFO "usb_devdrv: ");printk(fmt, ## args)
-
-#define irq_dbg(fmt, args...) \
-        printk(KERN_INFO "crisv10_irq dbg: ");printk(fmt, ## args)
-#define irq_err(fmt, args...) \
-        printk(KERN_ERR "crisv10_irq error: ");printk(fmt, ## args)
-#define irq_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_irq warn: ");printk(fmt, ## args)
-#define irq_info(fmt, args...) \
-        printk(KERN_INFO "crisv10_hcd: ");printk(fmt, ## args)
-
-/*
-#define rh_dbg(fmt, args...) \
-  printk(KERN_DEBUG "crisv10_rh dbg: ");printk(fmt, ## args)
-*/
-#define rh_dbg(fmt, args...) {}
-
-#define rh_err(fmt, args...) \
-        printk(KERN_ERR "crisv10_rh error: ");printk(fmt, ## args)
-#define rh_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_rh warning: ");printk(fmt, ## args)
-#define rh_info(fmt, args...) \
-        printk(KERN_INFO "crisv10_rh: ");printk(fmt, ## args)
-
-/*
-#define tc_dbg(fmt, args...) \
-        printk(KERN_INFO "crisv10_tc dbg: ");printk(fmt, ## args)
-*/
-#define tc_dbg(fmt, args...) {while(0){}}
-
-#define tc_err(fmt, args...) \
-        printk(KERN_ERR "crisv10_tc error: ");printk(fmt, ## args)
-/*
-#define tc_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_tc warning: ");printk(fmt, ## args)
-*/
-#define tc_warn(fmt, args...) {while(0){}}
-
-#define tc_info(fmt, args...) \
-        printk(KERN_INFO "crisv10_tc: ");printk(fmt, ## args)
-
-
-/* Debug print-outs for various traffic types */
-
-#define intr_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_intr warning: ");printk(fmt, ## args)
-/*
-#define intr_dbg(fmt, args...) \
-        printk(KERN_DEBUG "crisv10_intr dbg: ");printk(fmt, ## args)
-*/
-#define intr_dbg(fmt, args...) {while(0){}}
-
-
-#define isoc_err(fmt, args...) \
-        printk(KERN_ERR "crisv10_isoc error: ");printk(fmt, ## args)
-/*
-#define isoc_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_isoc warning: ");printk(fmt, ## args)
-*/
-#define isoc_warn(fmt, args...) {while(0){}}
-
-/*
-#define isoc_dbg(fmt, args...) \
-        printk(KERN_INFO "crisv10_isoc dbg: ");printk(fmt, ## args)
-*/
-#define isoc_dbg(fmt, args...) {while(0){}}
-
-/*
-#define timer_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_timer warning: ");printk(fmt, ## args)
-*/
-#define timer_warn(fmt, args...) {while(0){}}
-
-/*
-#define timer_dbg(fmt, args...) \
-        printk(KERN_INFO "crisv10_timer dbg: ");printk(fmt, ## args)
-*/
-#define timer_dbg(fmt, args...) {while(0){}}
-
-
-/* Debug printouts for events related to late finishing of URBs */
-/*
-#define late_dbg(fmt, args...) \
-        printk(KERN_INFO "crisv10_late dbg: ");printk(fmt, ## args)
-*/
-#define late_dbg(fmt, args...) {while(0){}}
-
-#define late_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_late warning: ");printk(fmt, ## args)
-/*
-#define errno_dbg(fmt, args...) \
-        printk(KERN_INFO "crisv10_errno dbg: ");printk(fmt, ## args)
-*/
-#define errno_dbg(fmt, args...) {while(0){}}
-
-
-#define dma_dbg(fmt, args...) \
-        printk(KERN_INFO "crisv10_dma dbg: ");printk(fmt, ## args)
-#define dma_err(fmt, args...) \
-        printk(KERN_ERR "crisv10_dma error: ");printk(fmt, ## args)
-#define dma_warn(fmt, args...) \
-        printk(KERN_INFO "crisv10_dma warning: ");printk(fmt, ## args)
-#define dma_info(fmt, args...) \
-        printk(KERN_INFO "crisv10_dma: ");printk(fmt, ## args)
-
-
-
-#define str_dir(pipe) \
-	(usb_pipeout(pipe) ? "out" : "in")
-#define str_type(pipe) \
-	({								\
-		char *s = "?";						\
-		switch (usb_pipetype(pipe)) {				\
-		case PIPE_ISOCHRONOUS:	s = "iso";  break;		\
-		case PIPE_INTERRUPT:	s = "intr"; break;		\
-		case PIPE_CONTROL:	s = "ctrl"; break;		\
-		case PIPE_BULK:		s = "bulk"; break;		\
-		};							\
-		s;							\
-	})
diff --git a/target/linux/etrax/files/drivers/usb/host/hc-crisv10.c b/target/linux/etrax/files/drivers/usb/host/hc-crisv10.c
deleted file mode 100644
index 146f689..0000000
--- a/target/linux/etrax/files/drivers/usb/host/hc-crisv10.c
+++ /dev/null
@@ -1,4985 +0,0 @@
-/*
- *
- * ETRAX 100LX USB Host Controller Driver
- *
- * Copyright (C) 2005 - 2008  Axis Communications AB
- *
- * Author: Konrad Eriksson <konrad.eriksson@axis.se>
- *
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/moduleparam.h>
-#include <linux/spinlock.h>
-#include <linux/usb.h>
-#include <linux/platform_device.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/io_interface_mux.h>
-
-#include "../core/hcd.h"
-#include "../core/hub.h"
-#include "hc-crisv10.h"
-#include "hc-cris-dbg.h"
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* Host Controller settings                                                */
-/***************************************************************************/
-/***************************************************************************/
-
-#define VERSION			"1.00-openwrt_diff"
-#define COPYRIGHT		"(c) 2005, 2006 Axis Communications AB"
-#define DESCRIPTION             "ETRAX 100LX USB Host Controller"
-
-#define ETRAX_USB_HC_IRQ USB_HC_IRQ_NBR
-#define ETRAX_USB_RX_IRQ USB_DMA_RX_IRQ_NBR
-#define ETRAX_USB_TX_IRQ USB_DMA_TX_IRQ_NBR
-
-/* Number of physical ports in Etrax 100LX */
-#define USB_ROOT_HUB_PORTS 2
-
-const char hc_name[] = "hc-crisv10";
-const char product_desc[] = DESCRIPTION;
-
-/* The number of epids is, among other things, used for pre-allocating
-   ctrl, bulk and isoc EP descriptors (one for each epid).
-   Assumed to be > 1 when initiating the DMA lists. */
-#define NBR_OF_EPIDS       32
-
-/* Support interrupt traffic intervals up to 128 ms. */
-#define MAX_INTR_INTERVAL  128
-
-/* If periodic traffic (intr or isoc) is to be used, then one entry in the EP
-   table must be "invalid". By this we mean that we shouldn't care about epid
-   attentions for this epid, or at least handle them differently from epid
-   attentions for "valid" epids. This define determines which one to use
-   (don't change it). */
-#define INVALID_EPID       31
-/* A special epid for the bulk dummys. */
-#define DUMMY_EPID         30
-
-/* Module settings */
-
-MODULE_DESCRIPTION(DESCRIPTION);
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Konrad Eriksson <konrad.eriksson@axis.se>");
-
-
-/* Module parameters */
-
-/* 0 = No ports enabled
-   1 = Only port 1 enabled (on board ethernet on devboard)
-   2 = Only port 2 enabled (external connector on devboard)
-   3 = Both ports enabled
-*/
-static unsigned int ports = 3;
-module_param(ports, uint, S_IRUGO);
-MODULE_PARM_DESC(ports, "Bitmask indicating USB ports to use");
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* Shared global variables for this module                                 */
-/***************************************************************************/
-/***************************************************************************/
-
-/* EP descriptor lists for non period transfers. Must be 32-bit aligned. */
-static volatile struct USB_EP_Desc TxBulkEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4)));
-
-static volatile struct USB_EP_Desc TxCtrlEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4)));
-
-/* EP descriptor lists for period transfers. Must be 32-bit aligned. */
-static volatile struct USB_EP_Desc TxIntrEPList[MAX_INTR_INTERVAL] __attribute__ ((aligned (4)));
-static volatile struct USB_SB_Desc TxIntrSB_zout __attribute__ ((aligned (4)));
-
-static volatile struct USB_EP_Desc TxIsocEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4)));
-static volatile struct USB_SB_Desc TxIsocSB_zout __attribute__ ((aligned (4)));
-
-static volatile struct USB_SB_Desc TxIsocSBList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); 
-
-/* After each enabled bulk EP IN we put two disabled EP descriptors with the eol flag set,
-   causing the DMA to stop the DMA channel. The first of these two has the intr flag set, which
-   gives us a dma8_sub0_descr interrupt. When we receive this, we advance the DMA one step in the
-   EP list and then restart the bulk channel, thus forcing a switch between bulk EP descriptors
-   in each frame. */
-static volatile struct USB_EP_Desc TxBulkDummyEPList[NBR_OF_EPIDS][2] __attribute__ ((aligned (4)));
-
-/* List of URB pointers, where each points to the active URB for a epid.
-   For Bulk, Ctrl and Intr this means which URB that currently is added to
-   DMA lists (Isoc URBs are all directly added to DMA lists). As soon as
-   URB has completed is the queue examined and the first URB in queue is
-   removed and moved to the activeUrbList while its state change to STARTED and
-   its transfer(s) gets added to DMA list (exception Isoc where URBs enter
-   state STARTED directly and added transfers added to DMA lists). */
-static struct urb *activeUrbList[NBR_OF_EPIDS];
-
-/* Additional software state info for each epid */
-static struct etrax_epid epid_state[NBR_OF_EPIDS];
-
-/* Timer handles for bulk traffic timer used to avoid DMA bug where DMA stops
-   even if there is new data waiting to be processed */
-static struct timer_list bulk_start_timer = TIMER_INITIALIZER(NULL, 0, 0);
-static struct timer_list bulk_eot_timer = TIMER_INITIALIZER(NULL, 0, 0);
-
-/* We want the start timer to expire before the eot timer, because the former
-   might start traffic, thus making it unnecessary for the latter to time
-   out. */
-#define BULK_START_TIMER_INTERVAL (HZ/50) /* 20 ms */
-#define BULK_EOT_TIMER_INTERVAL (HZ/16) /* 60 ms */
-
-/* Delay before a URB completion happen when it's scheduled to be delayed */
-#define LATER_TIMER_DELAY (HZ/50) /* 20 ms */
-
-/* Simplifying macros for checking software state info of a epid */
-/* ----------------------------------------------------------------------- */
-#define epid_inuse(epid)       epid_state[epid].inuse
-#define epid_out_traffic(epid) epid_state[epid].out_traffic
-#define epid_isoc(epid)   (epid_state[epid].type == PIPE_ISOCHRONOUS ? 1 : 0)
-#define epid_intr(epid)   (epid_state[epid].type == PIPE_INTERRUPT ? 1 : 0)
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* DEBUG FUNCTIONS                                                         */
-/***************************************************************************/
-/***************************************************************************/
-/* Note that these functions are always available in their "__" variants,
-   for use in error situations. The "__" missing variants are controlled by
-   the USB_DEBUG_DESC/USB_DEBUG_URB macros. */
-static void __dump_urb(struct urb* purb)
-{
-  struct crisv10_urb_priv *urb_priv = purb->hcpriv;
-  int urb_num = -1;
-  if(urb_priv) {
-    urb_num = urb_priv->urb_num;
-  }
-  printk("\nURB:0x%x[%d]\n", (unsigned int)purb, urb_num);
-  printk("dev                   :0x%08lx\n", (unsigned long)purb->dev);
-  printk("pipe                  :0x%08x\n", purb->pipe);
-  printk("status                :%d\n", purb->status);
-  printk("transfer_flags        :0x%08x\n", purb->transfer_flags);
-  printk("transfer_buffer       :0x%08lx\n", (unsigned long)purb->transfer_buffer);
-  printk("transfer_buffer_length:%d\n", purb->transfer_buffer_length);
-  printk("actual_length         :%d\n", purb->actual_length);
-  printk("setup_packet          :0x%08lx\n", (unsigned long)purb->setup_packet);
-  printk("start_frame           :%d\n", purb->start_frame);
-  printk("number_of_packets     :%d\n", purb->number_of_packets);
-  printk("interval              :%d\n", purb->interval);
-  printk("error_count           :%d\n", purb->error_count);
-  printk("context               :0x%08lx\n", (unsigned long)purb->context);
-  printk("complete              :0x%08lx\n\n", (unsigned long)purb->complete);
-}
-
-static void __dump_in_desc(volatile struct USB_IN_Desc *in)
-{
-  printk("\nUSB_IN_Desc at 0x%08lx\n", (unsigned long)in);
-  printk("  sw_len  : 0x%04x (%d)\n", in->sw_len, in->sw_len);
-  printk("  command : 0x%04x\n", in->command);
-  printk("  next    : 0x%08lx\n", in->next);
-  printk("  buf     : 0x%08lx\n", in->buf);
-  printk("  hw_len  : 0x%04x (%d)\n", in->hw_len, in->hw_len);
-  printk("  status  : 0x%04x\n\n", in->status);
-}
-
-static void __dump_sb_desc(volatile struct USB_SB_Desc *sb)
-{
-  char tt = (sb->command & 0x30) >> 4;
-  char *tt_string;
-
-  switch (tt) {
-  case 0:
-    tt_string = "zout";
-    break;
-  case 1:
-    tt_string = "in";
-    break;
-  case 2:
-    tt_string = "out";
-    break;
-  case 3:
-    tt_string = "setup";
-    break;
-  default:
-    tt_string = "unknown (weird)";
-  }
-
-  printk(" USB_SB_Desc at 0x%08lx ", (unsigned long)sb);
-  printk(" command:0x%04x (", sb->command);
-  printk("rem:%d ", (sb->command & 0x3f00) >> 8);
-  printk("full:%d ", (sb->command & 0x40) >> 6);
-  printk("tt:%d(%s) ", tt, tt_string);
-  printk("intr:%d ", (sb->command & 0x8) >> 3);
-  printk("eot:%d ", (sb->command & 0x2) >> 1);
-  printk("eol:%d)", sb->command & 0x1);
-  printk(" sw_len:0x%04x(%d)", sb->sw_len, sb->sw_len);
-  printk(" next:0x%08lx", sb->next);
-  printk(" buf:0x%08lx\n", sb->buf);
-}
-
-
-static void __dump_ep_desc(volatile struct USB_EP_Desc *ep)
-{
-  printk("USB_EP_Desc at 0x%08lx ", (unsigned long)ep);
-  printk(" command:0x%04x (", ep->command);
-  printk("ep_id:%d ", (ep->command & 0x1f00) >> 8);
-  printk("enable:%d ", (ep->command & 0x10) >> 4);
-  printk("intr:%d ", (ep->command & 0x8) >> 3);
-  printk("eof:%d ", (ep->command & 0x2) >> 1);
-  printk("eol:%d)", ep->command & 0x1);
-  printk(" hw_len:0x%04x(%d)", ep->hw_len, ep->hw_len);
-  printk(" next:0x%08lx", ep->next);
-  printk(" sub:0x%08lx\n", ep->sub);
-}
-
-static inline void __dump_ep_list(int pipe_type)
-{
-  volatile struct USB_EP_Desc *ep;
-  volatile struct USB_EP_Desc *first_ep;
-  volatile struct USB_SB_Desc *sb;
-
-  switch (pipe_type)
-    {
-    case PIPE_BULK:
-      first_ep = &TxBulkEPList[0];
-      break;
-    case PIPE_CONTROL:
-      first_ep = &TxCtrlEPList[0];
-      break;
-    case PIPE_INTERRUPT:
-      first_ep = &TxIntrEPList[0];
-      break;
-    case PIPE_ISOCHRONOUS:
-      first_ep = &TxIsocEPList[0];
-      break;
-    default:
-      warn("Cannot dump unknown traffic type");
-      return;
-    }
-  ep = first_ep;
-
-  printk("\n\nDumping EP list...\n\n");
-
-  do {
-    __dump_ep_desc(ep);
-    /* Cannot phys_to_virt on 0 as it turns into 80000000, which is != 0. */
-    sb = ep->sub ? phys_to_virt(ep->sub) : 0;
-    while (sb) {
-      __dump_sb_desc(sb);
-      sb = sb->next ? phys_to_virt(sb->next) : 0;
-    }
-    ep = (volatile struct USB_EP_Desc *)(phys_to_virt(ep->next));
-
-  } while (ep != first_ep);
-}
-
-static inline void __dump_ept_data(int epid)
-{
-  unsigned long flags;
-  __u32 r_usb_ept_data;
-
-  if (epid < 0 || epid > 31) {
-    printk("Cannot dump ept data for invalid epid %d\n", epid);
-    return;
-  }
-
-  local_irq_save(flags);
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid);
-  nop();
-  r_usb_ept_data = *R_USB_EPT_DATA;
-  local_irq_restore(flags);
-
-  printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", r_usb_ept_data, epid);
-  if (r_usb_ept_data == 0) {
-    /* No need for more detailed printing. */
-    return;
-  }
-  printk("  valid           : %d\n", (r_usb_ept_data & 0x80000000) >> 31);
-  printk("  hold            : %d\n", (r_usb_ept_data & 0x40000000) >> 30);
-  printk("  error_count_in  : %d\n", (r_usb_ept_data & 0x30000000) >> 28);
-  printk("  t_in            : %d\n", (r_usb_ept_data & 0x08000000) >> 27);
-  printk("  low_speed       : %d\n", (r_usb_ept_data & 0x04000000) >> 26);
-  printk("  port            : %d\n", (r_usb_ept_data & 0x03000000) >> 24);
-  printk("  error_code      : %d\n", (r_usb_ept_data & 0x00c00000) >> 22);
-  printk("  t_out           : %d\n", (r_usb_ept_data & 0x00200000) >> 21);
-  printk("  error_count_out : %d\n", (r_usb_ept_data & 0x00180000) >> 19);
-  printk("  max_len         : %d\n", (r_usb_ept_data & 0x0003f800) >> 11);
-  printk("  ep              : %d\n", (r_usb_ept_data & 0x00000780) >> 7);
-  printk("  dev             : %d\n", (r_usb_ept_data & 0x0000003f));
-}
-
-static inline void __dump_ept_data_iso(int epid)
-{
-  unsigned long flags;
-  __u32 ept_data;
-
-  if (epid < 0 || epid > 31) {
-    printk("Cannot dump ept data for invalid epid %d\n", epid);
-    return;
-  }
-
-  local_irq_save(flags);
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid);
-  nop();
-  ept_data = *R_USB_EPT_DATA_ISO;
-  local_irq_restore(flags);
-
-  printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", ept_data, epid);
-  if (ept_data == 0) {
-    /* No need for more detailed printing. */
-    return;
-  }
-  printk("  valid           : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, valid,
-						ept_data));
-  printk("  port            : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, port,
-						ept_data));
-  printk("  error_code      : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code,
-						ept_data));
-  printk("  max_len         : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, max_len,
-						ept_data));
-  printk("  ep              : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, ep,
-						ept_data));
-  printk("  dev             : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, dev,
-						ept_data));
-}
-
-static inline void __dump_ept_data_list(void)
-{
-  int i;
-
-  printk("Dumping the whole R_USB_EPT_DATA list\n");
-
-  for (i = 0; i < 32; i++) {
-    __dump_ept_data(i);
-  }
-}
-
-static void debug_epid(int epid) {
-  int i;
-  
-  if(epid_isoc(epid)) {
-    __dump_ept_data_iso(epid);
-  } else {
-    __dump_ept_data(epid);
-  }
-
-  printk("Bulk:\n");
-  for(i = 0; i < 32; i++) {
-    if(IO_EXTRACT(USB_EP_command, epid, TxBulkEPList[i].command) ==
-       epid) {
-      printk("%d: ", i); __dump_ep_desc(&(TxBulkEPList[i]));
-    }
-  }
-
-  printk("Ctrl:\n");
-  for(i = 0; i < 32; i++) {
-    if(IO_EXTRACT(USB_EP_command, epid, TxCtrlEPList[i].command) ==
-       epid) {
-      printk("%d: ", i); __dump_ep_desc(&(TxCtrlEPList[i]));
-    }
-  }
-
-  printk("Intr:\n");
-  for(i = 0; i < MAX_INTR_INTERVAL; i++) {
-    if(IO_EXTRACT(USB_EP_command, epid, TxIntrEPList[i].command) ==
-       epid) {
-      printk("%d: ", i); __dump_ep_desc(&(TxIntrEPList[i]));
-    }
-  }
-  
-  printk("Isoc:\n");
-  for(i = 0; i < 32; i++) {
-    if(IO_EXTRACT(USB_EP_command, epid, TxIsocEPList[i].command) ==
-       epid) {
-      printk("%d: ", i); __dump_ep_desc(&(TxIsocEPList[i]));
-    }
-  }
-
-  __dump_ept_data_list();
-  __dump_ep_list(PIPE_INTERRUPT);
-  printk("\n\n");
-}
-
-
-
-char* hcd_status_to_str(__u8 bUsbStatus) {
-  static char hcd_status_str[128];
-  hcd_status_str[0] = '\0';
-  if(bUsbStatus & IO_STATE(R_USB_STATUS, ourun, yes)) {
-    strcat(hcd_status_str, "ourun ");
-  }
-  if(bUsbStatus & IO_STATE(R_USB_STATUS, perror, yes)) {
-    strcat(hcd_status_str, "perror ");
-  }
-  if(bUsbStatus & IO_STATE(R_USB_STATUS, device_mode, yes)) {
-    strcat(hcd_status_str, "device_mode ");
-  }
-  if(bUsbStatus & IO_STATE(R_USB_STATUS, host_mode, yes)) {
-    strcat(hcd_status_str, "host_mode ");
-  }
-  if(bUsbStatus & IO_STATE(R_USB_STATUS, started, yes)) {
-    strcat(hcd_status_str, "started ");
-  }
-  if(bUsbStatus & IO_STATE(R_USB_STATUS, running, yes)) {
-    strcat(hcd_status_str, "running ");
-  }
-  return hcd_status_str;
-}
-
-
-char* sblist_to_str(struct USB_SB_Desc* sb_desc) {
-  static char sblist_to_str_buff[128];
-  char tmp[32], tmp2[32];
-  sblist_to_str_buff[0] = '\0';
-  while(sb_desc != NULL) {
-    switch(IO_EXTRACT(USB_SB_command, tt, sb_desc->command)) {
-    case 0: sprintf(tmp, "zout");  break;
-    case 1: sprintf(tmp, "in");    break;
-    case 2: sprintf(tmp, "out");   break;
-    case 3: sprintf(tmp, "setup"); break;
-    }
-    sprintf(tmp2, "(%s %d)", tmp, sb_desc->sw_len);
-    strcat(sblist_to_str_buff, tmp2);
-    if(sb_desc->next != 0) {
-      sb_desc = phys_to_virt(sb_desc->next);
-    } else {
-      sb_desc = NULL;
-    }
-  }
-  return sblist_to_str_buff;
-}
-
-char* port_status_to_str(__u16 wPortStatus) {
-  static char port_status_str[128];
-  port_status_str[0] = '\0';
-  if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes)) {
-    strcat(port_status_str, "connected ");
-  }
-  if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) {
-    strcat(port_status_str, "enabled ");
-  }
-  if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, suspended, yes)) {
-    strcat(port_status_str, "suspended ");
-  }
-  if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, reset, yes)) {
-    strcat(port_status_str, "reset ");
-  }
-  if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, speed, full)) {
-    strcat(port_status_str, "full-speed ");
-  } else {
-    strcat(port_status_str, "low-speed ");
-  }
-  return port_status_str;
-}
-
-
-char* endpoint_to_str(struct usb_endpoint_descriptor *ed) {
-  static char endpoint_to_str_buff[128];
-  char tmp[32];
-  int epnum = ed->bEndpointAddress & 0x0F;
-  int dir = ed->bEndpointAddress & 0x80;
-  int type = ed->bmAttributes & 0x03;
-  endpoint_to_str_buff[0] = '\0';
-  sprintf(endpoint_to_str_buff, "ep:%d ", epnum);
-  switch(type) {
-  case 0:
-    sprintf(tmp, " ctrl");
-    break;
-  case 1:
-    sprintf(tmp, " isoc");
-    break;
-  case 2:
-    sprintf(tmp, " bulk");
-    break;
-  case 3:
-    sprintf(tmp, " intr");
-    break;
-  }
-  strcat(endpoint_to_str_buff, tmp);
-  if(dir) {
-    sprintf(tmp, " in");
-  } else {
-    sprintf(tmp, " out");
-  }
-  strcat(endpoint_to_str_buff, tmp);
-
-  return endpoint_to_str_buff;
-}
-
-/* Debug helper functions for Transfer Controller */
-char* pipe_to_str(unsigned int pipe) {
-  static char pipe_to_str_buff[128];
-  char tmp[64];
-  sprintf(pipe_to_str_buff, "dir:%s", str_dir(pipe));
-  sprintf(tmp, " type:%s", str_type(pipe));
-  strcat(pipe_to_str_buff, tmp);
-
-  sprintf(tmp, " dev:%d", usb_pipedevice(pipe));
-  strcat(pipe_to_str_buff, tmp);
-  sprintf(tmp, " ep:%d", usb_pipeendpoint(pipe));
-  strcat(pipe_to_str_buff, tmp);
-  return pipe_to_str_buff;
-}
-
-
-#define USB_DEBUG_DESC 1
-
-#ifdef USB_DEBUG_DESC
-#define dump_in_desc(x) __dump_in_desc(x)
-#define dump_sb_desc(...) __dump_sb_desc(...)
-#define dump_ep_desc(x) __dump_ep_desc(x)
-#define dump_ept_data(x) __dump_ept_data(x)
-#else
-#define dump_in_desc(...) do {} while (0)
-#define dump_sb_desc(...) do {} while (0)
-#define dump_ep_desc(...) do {} while (0)
-#endif
-
-
-/* Uncomment this to enable massive function call trace
-   #define USB_DEBUG_TRACE */
-
-#ifdef USB_DEBUG_TRACE
-#define DBFENTER (printk(": Entering: %s\n", __FUNCTION__))
-#define DBFEXIT  (printk(": Exiting:  %s\n", __FUNCTION__))
-#else
-#define DBFENTER do {} while (0)
-#define DBFEXIT  do {} while (0)
-#endif
-
-#define CHECK_ALIGN(x) if (((__u32)(x)) & 0x00000003) \
-{panic("Alignment check (DWORD) failed at %s:%s:%d\n", __FILE__, __FUNCTION__, __LINE__);}
-
-/* Most helpful debugging aid */
-#define ASSERT(expr) ((void) ((expr) ? 0 : (err("assert failed at: %s %d",__FUNCTION__, __LINE__))))
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* Forward declarations                                                    */
-/***************************************************************************/
-/***************************************************************************/
-void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg);
-void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg);
-void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg);
-void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg);
-
-void rh_port_status_change(__u16[]);
-int  rh_clear_port_feature(__u8, __u16);
-int  rh_set_port_feature(__u8, __u16);
-static void rh_disable_port(unsigned int port);
-
-static void check_finished_bulk_tx_epids(struct usb_hcd *hcd,
-					 int timer);
-
-static int  tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb,
-			 int mem_flags);
-static void tc_free_epid(struct usb_host_endpoint *ep);
-static int  tc_allocate_epid(void);
-static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status);
-static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb,
-				int status);
-
-static int  urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid,
-			   int mem_flags);
-static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb);
-
-static int crisv10_usb_check_bandwidth(struct usb_device *dev,struct urb *urb);
-static void crisv10_usb_claim_bandwidth(
-	struct usb_device *dev, struct urb *urb, int bustime, int isoc);
-static void crisv10_usb_release_bandwidth(
-	struct usb_hcd *hcd, int isoc, int bandwidth);
-
-static inline struct urb *urb_list_first(int epid);
-static inline void        urb_list_add(struct urb *urb, int epid,
-				      int mem_flags);
-static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid);
-static inline void        urb_list_del(struct urb *urb, int epid);
-static inline void        urb_list_move_last(struct urb *urb, int epid);
-static inline struct urb *urb_list_next(struct urb *urb, int epid);
-
-int create_sb_for_urb(struct urb *urb, int mem_flags);
-int init_intr_urb(struct urb *urb, int mem_flags);
-
-static inline void  etrax_epid_set(__u8 index, __u32 data);
-static inline void  etrax_epid_clear_error(__u8 index);
-static inline void  etrax_epid_set_toggle(__u8 index, __u8 dirout,
-					      __u8 toggle);
-static inline __u8  etrax_epid_get_toggle(__u8 index, __u8 dirout);
-static inline __u32 etrax_epid_get(__u8 index);
-
-/* We're accessing the same register position in Etrax so
-   when we do full access the internal difference doesn't matter */
-#define etrax_epid_iso_set(index, data) etrax_epid_set(index, data)
-#define etrax_epid_iso_get(index) etrax_epid_get(index)
-
-
-static void        tc_dma_process_isoc_urb(struct urb *urb);
-static void        tc_dma_process_queue(int epid);
-static void        tc_dma_unlink_intr_urb(struct urb *urb);
-static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc);
-static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc);
-
-static void tc_bulk_start_timer_func(unsigned long dummy);
-static void tc_bulk_eot_timer_func(unsigned long dummy);
-
-
-/*************************************************************/
-/*************************************************************/
-/* Host Controler Driver block                               */
-/*************************************************************/
-/*************************************************************/
-
-/* HCD operations */
-static irqreturn_t crisv10_hcd_top_irq(int irq, void*);
-static int crisv10_hcd_reset(struct usb_hcd *);
-static int crisv10_hcd_start(struct usb_hcd *);
-static void crisv10_hcd_stop(struct usb_hcd *);
-#ifdef CONFIG_PM
-static int crisv10_hcd_suspend(struct device *, u32, u32);
-static int crisv10_hcd_resume(struct device *, u32);
-#endif /* CONFIG_PM */
-static int crisv10_hcd_get_frame(struct usb_hcd *);
-
-static int  tc_urb_enqueue(struct usb_hcd *, struct urb *, gfp_t mem_flags);
-static int  tc_urb_dequeue(struct usb_hcd *, struct urb *, int);
-static void tc_endpoint_disable(struct usb_hcd *, struct usb_host_endpoint *ep);
-
-static int rh_status_data_request(struct usb_hcd *, char *);
-static int rh_control_request(struct usb_hcd *, u16, u16, u16, char*, u16);
-
-#ifdef CONFIG_PM
-static int crisv10_hcd_hub_suspend(struct usb_hcd *);
-static int crisv10_hcd_hub_resume(struct usb_hcd *);
-#endif /* CONFIG_PM */
-#ifdef CONFIG_USB_OTG
-static int crisv10_hcd_start_port_reset(struct usb_hcd *, unsigned);
-#endif /* CONFIG_USB_OTG */
-
-/* host controller driver interface */
-static const struct hc_driver crisv10_hc_driver = 
-  {
-    .description =	hc_name,
-    .product_desc =	product_desc,
-    .hcd_priv_size =	sizeof(struct crisv10_hcd),
-
-    /* Attaching IRQ handler manualy in probe() */
-    /* .irq =		crisv10_hcd_irq, */
-
-    .flags =		HCD_USB11,
-
-    /* called to init HCD and root hub */
-    .reset =		crisv10_hcd_reset,
-    .start =		crisv10_hcd_start,	
-
-    /* cleanly make HCD stop writing memory and doing I/O */
-    .stop =		crisv10_hcd_stop,
-
-    /* return current frame number */
-    .get_frame_number =	crisv10_hcd_get_frame,
-
-
-    /* Manage i/o requests via the Transfer Controller */
-    .urb_enqueue =	tc_urb_enqueue,
-    .urb_dequeue =	tc_urb_dequeue,
-
-    /* hw synch, freeing endpoint resources that urb_dequeue can't */
-    .endpoint_disable = tc_endpoint_disable,
-
-
-    /* Root Hub support */
-    .hub_status_data =	rh_status_data_request,
-    .hub_control =	rh_control_request,
-#ifdef CONFIG_PM
-    .hub_suspend =	rh_suspend_request,
-    .hub_resume =	rh_resume_request,
-#endif /* CONFIG_PM */
-#ifdef	CONFIG_USB_OTG
-    .start_port_reset =	crisv10_hcd_start_port_reset,
-#endif /* CONFIG_USB_OTG */
-  };
-
-
-/*
- * conversion between pointers to a hcd and the corresponding
- * crisv10_hcd 
- */
-
-static inline struct crisv10_hcd *hcd_to_crisv10_hcd(struct usb_hcd *hcd)
-{
-	return (struct crisv10_hcd *) hcd->hcd_priv;
-}
-
-static inline struct usb_hcd *crisv10_hcd_to_hcd(struct crisv10_hcd *hcd)
-{
-	return container_of((void *) hcd, struct usb_hcd, hcd_priv);
-}
-
-/* check if specified port is in use */
-static inline int port_in_use(unsigned int port)
-{
-	return ports & (1 << port);
-}
-
-/* number of ports in use */
-static inline unsigned int num_ports(void)
-{
-	unsigned int i, num = 0;
-	for (i = 0; i < USB_ROOT_HUB_PORTS; i++)
-		if (port_in_use(i))
-			num++;
-	return num;
-}
-
-/* map hub port number to the port number used internally by the HC */
-static inline unsigned int map_port(unsigned int port)
-{
-  unsigned int i, num = 0;
-  for (i = 0; i < USB_ROOT_HUB_PORTS; i++)
-    if (port_in_use(i))
-      if (++num == port)
-	return i;
-  return -1;
-}
-
-/* size of descriptors in slab cache */
-#ifndef MAX
-#define MAX(x, y)		((x) > (y) ? (x) : (y))
-#endif
-
-
-/******************************************************************/
-/* Hardware Interrupt functions                                   */
-/******************************************************************/
-
-/* Fast interrupt handler for HC */
-static irqreturn_t crisv10_hcd_top_irq(int irq, void *vcd)
-{
-  struct usb_hcd *hcd = vcd;
-  struct crisv10_irq_reg reg;
-  __u32 irq_mask;
-  unsigned long flags;
-
-  DBFENTER;
-
-  ASSERT(hcd != NULL);
-  reg.hcd = hcd;
-
-  /* Turn of other interrupts while handling these sensitive cases */
-  local_irq_save(flags);
-  
-  /* Read out which interrupts that are flaged */
-  irq_mask = *R_USB_IRQ_MASK_READ;
-  reg.r_usb_irq_mask_read = irq_mask;
-
-  /* Reading R_USB_STATUS clears the ctl_status interrupt. Note that
-     R_USB_STATUS must be read before R_USB_EPID_ATTN since reading the latter
-     clears the ourun and perror fields of R_USB_STATUS. */
-  reg.r_usb_status = *R_USB_STATUS;
-  
-  /* Reading R_USB_EPID_ATTN clears the iso_eof, bulk_eot and epid_attn
-     interrupts. */
-  reg.r_usb_epid_attn = *R_USB_EPID_ATTN;
-  
-  /* Reading R_USB_RH_PORT_STATUS_1 and R_USB_RH_PORT_STATUS_2 clears the
-     port_status interrupt. */
-  reg.r_usb_rh_port_status_1 = *R_USB_RH_PORT_STATUS_1;
-  reg.r_usb_rh_port_status_2 = *R_USB_RH_PORT_STATUS_2;
-  
-  /* Reading R_USB_FM_NUMBER clears the sof interrupt. */
-  /* Note: the lower 11 bits contain the actual frame number, sent with each
-     sof. */
-  reg.r_usb_fm_number = *R_USB_FM_NUMBER;
-
-  /* Interrupts are handled in order of priority. */
-  if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, port_status)) {
-    crisv10_hcd_port_status_irq(&reg);
-  }
-  if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, epid_attn)) {
-    crisv10_hcd_epid_attn_irq(&reg);
-  }
-  if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, ctl_status)) {
-    crisv10_hcd_ctl_status_irq(&reg);
-  }
-  if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, iso_eof)) {
-    crisv10_hcd_isoc_eof_irq(&reg);
-  }
-  if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, bulk_eot)) {
-    /* Update/restart the bulk start timer since obviously the channel is
-       running. */
-    mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL);
-    /* Update/restart the bulk eot timer since we just received an bulk eot
-       interrupt. */
-    mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL);
-
-    /* Check for finished bulk transfers on epids */
-    check_finished_bulk_tx_epids(hcd, 0);
-  }
-  local_irq_restore(flags);
-
-  DBFEXIT;
-  return IRQ_HANDLED;
-}
-
-
-void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg) {
-  struct usb_hcd *hcd = reg->hcd;
-  struct crisv10_urb_priv *urb_priv;
-  int epid;
-  DBFENTER;
-
-  for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
-    if (test_bit(epid, (void *)&reg->r_usb_epid_attn)) {
-      struct urb *urb;
-      __u32 ept_data;
-      int error_code;
-
-      if (epid == DUMMY_EPID || epid == INVALID_EPID) {
-	/* We definitely don't care about these ones. Besides, they are
-	   always disabled, so any possible disabling caused by the
-	   epid attention interrupt is irrelevant. */
-	warn("Got epid_attn for INVALID_EPID or DUMMY_EPID (%d).", epid);
-	continue;
-      }
-
-      if(!epid_inuse(epid)) {
-	irq_err("Epid attention on epid:%d that isn't in use\n", epid);
-	printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
-	debug_epid(epid);
-	continue;
-      }
-
-      /* Note that although there are separate R_USB_EPT_DATA and
-	 R_USB_EPT_DATA_ISO registers, they are located at the same address and
-	 are of the same size. In other words, this read should be ok for isoc
-	 also. */
-      ept_data = etrax_epid_get(epid);
-      error_code = IO_EXTRACT(R_USB_EPT_DATA, error_code, ept_data);
-
-      /* Get the active URB for this epid. We blatantly assume
-	 that only this URB could have caused the epid attention. */
-      urb = activeUrbList[epid];
-      if (urb == NULL) {
-	irq_err("Attention on epid:%d error:%d with no active URB.\n",
-		epid, error_code);
-	printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
-	debug_epid(epid);
-	continue;
-      }
-
-      urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-      ASSERT(urb_priv);
-
-      /* Using IO_STATE_VALUE on R_USB_EPT_DATA should be ok for isoc also. */
-      if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
-
-	/* Isoc traffic doesn't have error_count_in/error_count_out. */
-	if ((usb_pipetype(urb->pipe) != PIPE_ISOCHRONOUS) &&
-	    (IO_EXTRACT(R_USB_EPT_DATA, error_count_in, ept_data) == 3 ||
-	     IO_EXTRACT(R_USB_EPT_DATA, error_count_out, ept_data) == 3)) {
-	  /* Check if URB allready is marked for late-finish, we can get
-	     several 3rd error for Intr traffic when a device is unplugged */
-	  if(urb_priv->later_data == NULL) {
-	    /* 3rd error. */
-	    irq_warn("3rd error for epid:%d (%s %s) URB:0x%x[%d]\n", epid,
-		     str_dir(urb->pipe), str_type(urb->pipe),
-		     (unsigned int)urb, urb_priv->urb_num);
-	  
-	    tc_finish_urb_later(hcd, urb, -EPROTO);
-	  }
-
-	} else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) {
-	  irq_warn("Perror for epid:%d\n", epid);
-	  printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff);
-	  printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
-	  __dump_urb(urb);
-	  debug_epid(epid);
-
-	  if (!(ept_data & IO_MASK(R_USB_EPT_DATA, valid))) {
-	    /* invalid ep_id */
-	    panic("Perror because of invalid epid."
-		  " Deconfigured too early?");
-	  } else {
-	    /* past eof1, near eof, zout transfer, setup transfer */
-	    /* Dump the urb and the relevant EP descriptor. */
-	    panic("Something wrong with DMA descriptor contents."
-		  " Too much traffic inserted?");
-	  }
-	} else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) {
-	  /* buffer ourun */
-	  printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff);
-	  printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
-	  __dump_urb(urb);
-	  debug_epid(epid);
-
-	  panic("Buffer overrun/underrun for epid:%d. DMA too busy?", epid);
-	} else {
-	  irq_warn("Attention on epid:%d (%s %s) with no error code\n", epid,
-		   str_dir(urb->pipe), str_type(urb->pipe));
-	  printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
-	  __dump_urb(urb);
-	  debug_epid(epid);
-	}
-
-      } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code,
-					      stall)) {
-	/* Not really a protocol error, just says that the endpoint gave
-	   a stall response. Note that error_code cannot be stall for isoc. */
-	if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
-	  panic("Isoc traffic cannot stall");
-	}
-
-	tc_dbg("Stall for epid:%d (%s %s) URB:0x%x\n", epid,
-	       str_dir(urb->pipe), str_type(urb->pipe), (unsigned int)urb);
-	tc_finish_urb(hcd, urb, -EPIPE);
-
-      } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code,
-					      bus_error)) {
-	/* Two devices responded to a transaction request. Must be resolved
-	   by software. FIXME: Reset ports? */
-	panic("Bus error for epid %d."
-	      " Two devices responded to transaction request\n",
-	      epid);
-
-      } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code,
-					      buffer_error)) {
-	/* DMA overrun or underrun. */
-	irq_warn("Buffer overrun/underrun for epid:%d (%s %s)\n", epid,
-		 str_dir(urb->pipe), str_type(urb->pipe));
-
-	/* It seems that error_code = buffer_error in
-	   R_USB_EPT_DATA/R_USB_EPT_DATA_ISO and ourun = yes in R_USB_STATUS
-	   are the same error. */
-	tc_finish_urb(hcd, urb, -EPROTO);
-      } else {
-	  irq_warn("Unknown attention on epid:%d (%s %s)\n", epid,
-		   str_dir(urb->pipe), str_type(urb->pipe));
-	  dump_ept_data(epid);
-      }
-    }
-  }
-  DBFEXIT;
-}
-
-void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg)
-{
-  __u16 port_reg[USB_ROOT_HUB_PORTS];
-  DBFENTER;
-  port_reg[0] = reg->r_usb_rh_port_status_1;
-  port_reg[1] = reg->r_usb_rh_port_status_2;
-  rh_port_status_change(port_reg);
-  DBFEXIT;
-}
-
-void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg)
-{
-  int epid;
-  struct urb *urb;
-  struct crisv10_urb_priv *urb_priv;
-
-  DBFENTER;
-
-  for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) {
-
-    /* Only check epids that are in use, is valid and has SB list */
-    if (!epid_inuse(epid) || epid == INVALID_EPID ||
-	TxIsocEPList[epid].sub == 0 || epid == DUMMY_EPID) {
-      /* Nothing here to see. */
-      continue;
-    }
-    ASSERT(epid_isoc(epid));
-
-    /* Get the active URB for this epid (if any). */
-    urb = activeUrbList[epid];
-    if (urb == 0) {
-      isoc_warn("Ignoring NULL urb for epid:%d\n", epid);
-      continue;
-    }
-    if(!epid_out_traffic(epid)) {
-      /* Sanity check. */
-      ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS);
-
-      urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-      ASSERT(urb_priv);
-
-      if (urb_priv->urb_state == NOT_STARTED) {
-	/* If ASAP is not set and urb->start_frame is the current frame,
-	   start the transfer. */
-	if (!(urb->transfer_flags & URB_ISO_ASAP) &&
-	    (urb->start_frame == (*R_USB_FM_NUMBER & 0x7ff))) {
-	  /* EP should not be enabled if we're waiting for start_frame */
-	  ASSERT((TxIsocEPList[epid].command &
-		  IO_STATE(USB_EP_command, enable, yes)) == 0);
-
-	  isoc_warn("Enabling isoc IN EP descr for epid %d\n", epid);
-	  TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
-
-	  /* This urb is now active. */
-	  urb_priv->urb_state = STARTED;
-	  continue;
-	}
-      }
-    }
-  }
-
-  DBFEXIT;
-}
-
-void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg)
-{
-  struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(reg->hcd);
-
-  DBFENTER;
-  ASSERT(crisv10_hcd);
-
-/*  irq_dbg("ctr_status_irq, controller status: %s\n",
-	  hcd_status_to_str(reg->r_usb_status));*/
-  
-  /* FIXME: What should we do if we get ourun or perror? Dump the EP and SB
-     list for the corresponding epid? */
-  if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) {
-    panic("USB controller got ourun.");
-  }
-  if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) {
-    
-    /* Before, etrax_usb_do_intr_recover was called on this epid if it was
-       an interrupt pipe. I don't see how re-enabling all EP descriptors
-       will help if there was a programming error. */
-    panic("USB controller got perror.");
-  }
-
-  /* Keep track of USB Controller, if it's running or not */
-  if(reg->r_usb_status & IO_STATE(R_USB_STATUS, running, yes)) {
-    crisv10_hcd->running = 1;
-  } else {
-    crisv10_hcd->running = 0;
-  }
-  
-  if (reg->r_usb_status & IO_MASK(R_USB_STATUS, device_mode)) {
-    /* We should never operate in device mode. */
-    panic("USB controller in device mode.");
-  }
-
-  /* Set the flag to avoid getting "Unlink after no-IRQ? Controller is probably
-     using the wrong IRQ" from hcd_unlink_urb() in drivers/usb/core/hcd.c */
-  set_bit(HCD_FLAG_SAW_IRQ, &reg->hcd->flags);
-  
-  DBFEXIT;
-}
-
-
-/******************************************************************/
-/* Host Controller interface functions                            */
-/******************************************************************/
-
-static inline void crisv10_ready_wait(void) {
-  volatile int timeout = 10000;
-  /* Check the busy bit of USB controller in Etrax */
-  while((*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)) &&
-	(timeout-- > 0));
-  if(timeout == 0) {
-    warn("Timeout while waiting for USB controller to be idle\n");
-  }
-}
-
-/* reset host controller */
-static int crisv10_hcd_reset(struct usb_hcd *hcd)
-{
-  DBFENTER;
-  hcd_dbg(hcd, "reset\n");
-
-
-  /* Reset the USB interface. */
-  /*
-  *R_USB_COMMAND =
-    IO_STATE(R_USB_COMMAND, port_sel, nop) |
-    IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-    IO_STATE(R_USB_COMMAND, ctrl_cmd, reset);
-  nop();
-  */
-  DBFEXIT;
-  return 0;
-}
-
-/* start host controller */
-static int crisv10_hcd_start(struct usb_hcd *hcd)
-{
-  DBFENTER;
-  hcd_dbg(hcd, "start\n");
-
-  crisv10_ready_wait();
-
-  /* Start processing of USB traffic. */
-  *R_USB_COMMAND =
-    IO_STATE(R_USB_COMMAND, port_sel, nop) |
-    IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-    IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
-
-  nop();
-
-  hcd->state = HC_STATE_RUNNING;
-
-  DBFEXIT;
-  return 0;
-}
-
-/* stop host controller */
-static void crisv10_hcd_stop(struct usb_hcd *hcd)
-{
-  DBFENTER;
-  hcd_dbg(hcd, "stop\n");
-  crisv10_hcd_reset(hcd);
-  DBFEXIT;
-}
-
-/* return the current frame number */
-static int crisv10_hcd_get_frame(struct usb_hcd *hcd)
-{
-  DBFENTER;
-  DBFEXIT;
-  return (*R_USB_FM_NUMBER & 0x7ff);
-}
-
-#ifdef	CONFIG_USB_OTG
-
-static int crisv10_hcd_start_port_reset(struct usb_hcd *hcd, unsigned port)
-{
-  return 0; /* no-op for now */
-}
-
-#endif /* CONFIG_USB_OTG */
-
-
-/******************************************************************/
-/* Root Hub functions                                             */
-/******************************************************************/
-
-/* root hub status */
-static const struct usb_hub_status rh_hub_status = 
-  {
-    .wHubStatus =		0,
-    .wHubChange =		0,
-  };
-
-/* root hub descriptor */
-static const u8 rh_hub_descr[] =
-  {
-    0x09,			/* bDescLength	       */
-    0x29,			/* bDescriptorType     */
-    USB_ROOT_HUB_PORTS,         /* bNbrPorts	       */
-    0x00,			/* wHubCharacteristics */
-    0x00,		 
-    0x01,			/* bPwrOn2pwrGood      */
-    0x00,			/* bHubContrCurrent    */
-    0x00,			/* DeviceRemovable     */
-    0xff			/* PortPwrCtrlMask     */
-  };
-
-/* Actual holder of root hub status*/
-struct crisv10_rh rh;
-
-/* Initialize root hub data structures (called from dvdrv_hcd_probe()) */
-int rh_init(void) {
-  int i;
-  /* Reset port status flags */
-  for (i = 0; i < USB_ROOT_HUB_PORTS; i++) {
-    rh.wPortChange[i] = 0;
-    rh.wPortStatusPrev[i] = 0;
-  }
-  return 0;
-}
-
-#define RH_FEAT_MASK ((1<<USB_PORT_FEAT_CONNECTION)|\
-		      (1<<USB_PORT_FEAT_ENABLE)|\
-		      (1<<USB_PORT_FEAT_SUSPEND)|\
-		      (1<<USB_PORT_FEAT_RESET))
-
-/* Handle port status change interrupt (called from bottom part interrupt) */
-void rh_port_status_change(__u16 port_reg[]) {
-  int i;
-  __u16 wChange;
-
-  for(i = 0; i < USB_ROOT_HUB_PORTS; i++) {
-    /* Xor out changes since last read, masked for important flags */
-    wChange = (port_reg[i] & RH_FEAT_MASK) ^ rh.wPortStatusPrev[i];
-    /* Or changes together with (if any) saved changes */
-    rh.wPortChange[i] |= wChange;
-    /* Save new status */
-    rh.wPortStatusPrev[i] = port_reg[i];
-
-    if(wChange) {
-      rh_dbg("Interrupt port_status change port%d: %s  Current-status:%s\n", i+1,
-	     port_status_to_str(wChange),
-	     port_status_to_str(port_reg[i]));
-    }
-  }
-}
-
-/* Construct port status change bitmap for the root hub */
-static int rh_status_data_request(struct usb_hcd *hcd, char *buf)
-{
-  struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd);
-  unsigned int i;
-
-  DBFENTER;
-  /*
-   * corresponds to hub status change EP (USB 2.0 spec section 11.13.4)
-   * return bitmap indicating ports with status change
-   */
-  *buf = 0;
-  spin_lock(&crisv10_hcd->lock);
-  for (i = 1; i <= crisv10_hcd->num_ports; i++) {
-    if (rh.wPortChange[map_port(i)]) {
-      *buf |= (1 << i);
-      rh_dbg("rh_status_data_request, change on port %d: %s  Current Status: %s\n", i,
-	     port_status_to_str(rh.wPortChange[map_port(i)]),
-	     port_status_to_str(rh.wPortStatusPrev[map_port(i)]));
-    }
-  }
-  spin_unlock(&crisv10_hcd->lock);
-  DBFEXIT;
-  return *buf == 0 ? 0 : 1;
-}
-
-/* Handle a control request for the root hub (called from hcd_driver) */
-static int rh_control_request(struct usb_hcd *hcd, 
-			      u16 typeReq, 
-			      u16 wValue, 
-			      u16 wIndex,
-			      char *buf, 
-			      u16 wLength) {
-
-  struct crisv10_hcd *crisv10_hcd = hcd_to_crisv10_hcd(hcd);
-  int retval = 0;
-  int len;
-  DBFENTER;
-
-  switch (typeReq) {
-  case GetHubDescriptor:
-    rh_dbg("GetHubDescriptor\n");
-    len = min_t(unsigned int, sizeof rh_hub_descr, wLength);
-    memcpy(buf, rh_hub_descr, len);
-    buf[2] = crisv10_hcd->num_ports;
-    break;
-  case GetHubStatus:
-    rh_dbg("GetHubStatus\n");
-    len = min_t(unsigned int, sizeof rh_hub_status, wLength);
-    memcpy(buf, &rh_hub_status, len);
-    break;
-  case GetPortStatus:
-    if (!wIndex || wIndex > crisv10_hcd->num_ports)
-      goto error;
-    rh_dbg("GetportStatus, port:%d change:%s  status:%s\n", wIndex,
-	   port_status_to_str(rh.wPortChange[map_port(wIndex)]),
-	   port_status_to_str(rh.wPortStatusPrev[map_port(wIndex)]));
-    *(u16 *) buf = cpu_to_le16(rh.wPortStatusPrev[map_port(wIndex)]);
-    *(u16 *) (buf + 2) = cpu_to_le16(rh.wPortChange[map_port(wIndex)]);
-    break;
-  case SetHubFeature:
-    rh_dbg("SetHubFeature\n");
-  case ClearHubFeature:
-    rh_dbg("ClearHubFeature\n");
-    switch (wValue) {
-    case C_HUB_OVER_CURRENT:
-    case C_HUB_LOCAL_POWER:
-      rh_warn("Not implemented hub request:%d \n", typeReq);
-      /* not implemented */
-      break;
-    default:
-      goto error;
-    }
-    break;
-  case SetPortFeature:
-    if (!wIndex || wIndex > crisv10_hcd->num_ports)
-      goto error;
-    if(rh_set_port_feature(map_port(wIndex), wValue))
-      goto error;
-    break;
-  case ClearPortFeature:
-    if (!wIndex || wIndex > crisv10_hcd->num_ports)
-      goto error;
-    if(rh_clear_port_feature(map_port(wIndex), wValue))
-      goto error;
-    break;
-  default:
-    rh_warn("Unknown hub request: %d\n", typeReq);
-  error:
-    retval = -EPIPE;
-  }
-  DBFEXIT;
-  return retval;
-}
-
-int rh_set_port_feature(__u8 bPort, __u16 wFeature) {
-  __u8 bUsbCommand = 0;
-  __u8 reset_cnt;
-  switch(wFeature) {
-  case USB_PORT_FEAT_RESET:
-    rh_dbg("SetPortFeature: reset\n");
-
-    if (rh.wPortStatusPrev[bPort] &
-        IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes))
-    {
-      __u8 restart_controller = 0;
-
-      if ( (rh.wPortStatusPrev[0] &
-            IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) &&
-           (rh.wPortStatusPrev[1] &
-            IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, yes)) )
-      {
-        /* Both ports is enabled. The USB controller will not change state. */
-        restart_controller = 0;
-      }
-      else
-      {
-        /* Only ports is enabled. The USB controller will change state and
-           must be restarted. */
-        restart_controller = 1;
-      }
-      /*
-        In ETRAX 100LX it's not possible to reset an enabled root hub port.
-        The workaround is to disable and enable the port before resetting it.
-        Disabling the port can, if both ports are disabled at once, cause the
-        USB controller to change state to HOST_MODE state. 
-        The USB controller state transition causes a lot of unwanted
-        interrupts that must be avoided.
-        Disabling the USB controller status and port status interrupts before
-        disabling/resetting the port stops these interrupts.
-
-        These actions are performed:
-        1. Disable USB controller status and port status interrupts.
-        2. Disable the port
-        3. Wait for the port to be disabled.
-        4. Enable the port.
-        5. Wait for the port to be enabled.
-        6. Reset the port.
-        7. Wait for for the reset to end.
-        8. Wait for the USB controller entering started state.
-        9. Order the USB controller to running state.
-        10. Wait for the USB controller reaching running state.
-        11. Clear all interrupts generated during the disable/enable/reset
-            procedure.
-        12. Enable the USB controller status and port status interrupts.
-      */
-
-      /* 1. Disable USB controller status and USB port status interrupts. */
-      *R_USB_IRQ_MASK_CLR = IO_STATE(R_USB_IRQ_MASK_CLR, ctl_status, clr);
-      __asm__ __volatile__ ("  nop");
-      *R_USB_IRQ_MASK_CLR = IO_STATE(R_USB_IRQ_MASK_CLR, port_status, clr);
-      __asm__ __volatile__ ("  nop");
-      
-      {
-
-        /* Since an root hub port reset shall be 50 ms and the ETRAX 100LX
-           root hub port reset is 10 ms we must perform 5 port resets to
-           achieve a proper root hub port reset. */
-        for (reset_cnt = 0; reset_cnt < 5; reset_cnt ++)
-        {
-          rh_dbg("Disable Port %d\n", bPort + 1);
-
-          /* 2. Disable the port*/
-          if (bPort == 0)
-          {
-            *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, yes);
-          }
-          else
-          {
-            *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, yes);
-          }
-
-          /* 3. Wait for the port to be disabled. */
-          while ( (bPort == 0) ?
-                  *R_USB_RH_PORT_STATUS_1 &
-                    IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes) :
-                  *R_USB_RH_PORT_STATUS_2 &
-                    IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, yes) ) {}
-
-          rh_dbg("Port %d is disabled. Enable it!\n", bPort + 1);
-
-          /* 4. Enable the port. */
-          if (bPort == 0)
-          {
-            *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no);
-          }
-          else
-          {
-            *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no);
-          }
-
-          /* 5. Wait for the port to be enabled again.  */
-          while (!( (bPort == 0) ?
-                    *R_USB_RH_PORT_STATUS_1 &
-                      IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes) :
-                    *R_USB_RH_PORT_STATUS_2 &
-                      IO_STATE(R_USB_RH_PORT_STATUS_2, connected, yes) ) ) {}
-
-          rh_dbg("Port %d is enabled.\n", bPort + 1);
-
-          /* 6. Reset the port */
-          crisv10_ready_wait();
-          *R_USB_COMMAND =
-            ( (bPort == 0) ?
-              IO_STATE(R_USB_COMMAND, port_sel, port1):
-              IO_STATE(R_USB_COMMAND, port_sel, port2) ) |
-            IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-            IO_STATE(R_USB_COMMAND, busy,     no) |
-            IO_STATE(R_USB_COMMAND, ctrl_cmd, nop);
-          rh_dbg("Port %d is resetting.\n", bPort + 1);
-
-          /* 7. The USB specification says that we should wait for at least
-             10ms for device recover */
-          udelay(10500); /* 10,5ms blocking wait */
-    
-          crisv10_ready_wait();
-        }
-      }
-
-
-      /* Check if the USB controller needs to be restarted. */
-      if (restart_controller)
-      {
-        /* 8. Wait for the USB controller entering started state. */
-        while (!(*R_USB_STATUS & IO_STATE(R_USB_STATUS, started, yes))) {}
-
-        /* 9. Order the USB controller to running state. */
-        crisv10_ready_wait();
-        *R_USB_COMMAND =
-          IO_STATE(R_USB_COMMAND, port_sel, nop) |
-          IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-          IO_STATE(R_USB_COMMAND, busy,     no) |
-          IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
-
-        /* 10. Wait for the USB controller reaching running state. */
-        while (!(*R_USB_STATUS & IO_STATE(R_USB_STATUS, running, yes))) {}
-      }
-
-      /* 11. Clear any controller or port satus interrupts before enabling
-             the interrupts. */
-      {
-        u16 dummy;
-
-        /* Clear the port status interrupt of the reset port. */
-        if (bPort == 0)
-        {
-          rh_dbg("Clearing port 1 interrupts\n");
-          dummy = *R_USB_RH_PORT_STATUS_1;
-        }
-        else
-        {
-          rh_dbg("Clearing port 2 interrupts\n");
-          dummy = *R_USB_RH_PORT_STATUS_2;
-        }
-
-        if (restart_controller)
-        {
-          /* The USB controller is restarted. Clear all interupts. */
-          rh_dbg("Clearing all interrupts\n");
-          dummy = *R_USB_STATUS;
-          dummy = *R_USB_RH_PORT_STATUS_1;
-          dummy = *R_USB_RH_PORT_STATUS_2;
-        }
-      }
-
-      /* 12. Enable USB controller status and USB port status interrupts.  */
-      *R_USB_IRQ_MASK_SET = IO_STATE(R_USB_IRQ_MASK_SET, ctl_status, set);
-      __asm__ __volatile__ ("  nop");
-      *R_USB_IRQ_MASK_SET = IO_STATE(R_USB_IRQ_MASK_SET, port_status, set);
-      __asm__ __volatile__ ("  nop");
-
-    }
-    else
-    {
-
-      bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, reset);
-      /* Select which port via the port_sel field */
-      bUsbCommand |= IO_FIELD(R_USB_COMMAND, port_sel, bPort+1);
-
-      /* Make sure the controller isn't busy. */
-      crisv10_ready_wait();
-      /* Send out the actual command to the USB controller */
-      *R_USB_COMMAND = bUsbCommand;
-
-      /* Wait a while for controller to first become started after port reset */
-      udelay(12000); /* 12ms blocking wait */
-      
-      /* Make sure the controller isn't busy. */
-      crisv10_ready_wait();
-
-      /* If all enabled ports were disabled the host controller goes down into
-         started mode, so we need to bring it back into the running state.
-         (This is safe even if it's already in the running state.) */
-      *R_USB_COMMAND =
-        IO_STATE(R_USB_COMMAND, port_sel, nop) |
-        IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-        IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
-    }
-
-    break;
-  case USB_PORT_FEAT_SUSPEND:
-    rh_dbg("SetPortFeature: suspend\n");
-    bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, suspend);
-    goto set;
-    break;
-  case USB_PORT_FEAT_POWER:
-    rh_dbg("SetPortFeature: power\n");
-    break;
-  case USB_PORT_FEAT_C_CONNECTION:
-    rh_dbg("SetPortFeature: c_connection\n");
-    break;
-  case USB_PORT_FEAT_C_RESET:
-    rh_dbg("SetPortFeature: c_reset\n");
-    break;
-  case USB_PORT_FEAT_C_OVER_CURRENT:
-    rh_dbg("SetPortFeature: c_over_current\n");
-    break;
-
-  set:
-    /* Select which port via the port_sel field */
-    bUsbCommand |= IO_FIELD(R_USB_COMMAND, port_sel, bPort+1);
-
-    /* Make sure the controller isn't busy. */
-    crisv10_ready_wait();
-    /* Send out the actual command to the USB controller */
-    *R_USB_COMMAND = bUsbCommand;
-    break;
-  default:
-    rh_dbg("SetPortFeature: unknown feature\n");
-    return -1;
-  }
-  return 0;
-}
-
-int rh_clear_port_feature(__u8 bPort, __u16 wFeature) {
-  switch(wFeature) {
-  case USB_PORT_FEAT_ENABLE:
-    rh_dbg("ClearPortFeature: enable\n");
-    rh_disable_port(bPort);
-    break;
-  case USB_PORT_FEAT_SUSPEND:
-    rh_dbg("ClearPortFeature: suspend\n");
-    break;
-  case USB_PORT_FEAT_POWER:
-    rh_dbg("ClearPortFeature: power\n");
-    break;
-
-  case USB_PORT_FEAT_C_ENABLE:
-    rh_dbg("ClearPortFeature: c_enable\n");
-    goto clear;
-  case USB_PORT_FEAT_C_SUSPEND:
-    rh_dbg("ClearPortFeature: c_suspend\n");
-    goto clear;
-  case USB_PORT_FEAT_C_CONNECTION:
-    rh_dbg("ClearPortFeature: c_connection\n");
-    goto clear;
-  case USB_PORT_FEAT_C_OVER_CURRENT:
-    rh_dbg("ClearPortFeature: c_over_current\n");
-    goto clear;
-  case USB_PORT_FEAT_C_RESET:
-    rh_dbg("ClearPortFeature: c_reset\n");
-    goto clear;
-  clear:
-    rh.wPortChange[bPort] &= ~(1 << (wFeature - 16));
-    break;
-  default:
-    rh_dbg("ClearPortFeature: unknown feature\n");
-    return -1;
-  }
-  return 0;
-}
-
-
-#ifdef	CONFIG_PM
-/* Handle a suspend request for the root hub (called from hcd_driver) */
-static int rh_suspend_request(struct usb_hcd *hcd)
-{
-  return 0; /* no-op for now */
-}
-
-/* Handle a resume request for the root hub (called from hcd_driver) */
-static int rh_resume_request(struct usb_hcd *hcd)
-{
-  return 0; /* no-op for now */
-}
-#endif /* CONFIG_PM */
-
-
-
-/* Wrapper function for workaround port disable registers in USB controller  */
-static void rh_disable_port(unsigned int port) {
-  volatile int timeout = 10000;
-  volatile char* usb_portx_disable;
-  switch(port) {
-  case 0:
-    usb_portx_disable = R_USB_PORT1_DISABLE;
-    break;
-  case 1:
-    usb_portx_disable = R_USB_PORT2_DISABLE;
-    break;
-  default:
-    /* Invalid port index */
-    return;
-  }
-  /* Set disable flag in special register  */
-  *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, yes);
-  /* Wait until not enabled anymore */
-  while((rh.wPortStatusPrev[port] &
-	IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) &&
-	(timeout-- > 0));
-  if(timeout == 0) {
-    warn("Timeout while waiting for port %d to become disabled\n", port);
-  }
-  /* clear disable flag in special register  */
-  *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, no);
-  rh_info("Physical port %d disabled\n", port+1);
-}
-
-
-/******************************************************************/
-/* Transfer Controller (TC) functions                             */
-/******************************************************************/
-
-/* FIXME: Should RX_BUF_SIZE be a config option, or maybe we should adjust it
-   dynamically?
-   To adjust it dynamically we would have to get an interrupt when we reach
-   the end of the rx descriptor list, or when we get close to the end, and
-   then allocate more descriptors. */
-#define NBR_OF_RX_DESC     512
-#define RX_DESC_BUF_SIZE   1024
-#define RX_BUF_SIZE        (NBR_OF_RX_DESC * RX_DESC_BUF_SIZE)
-
-
-/* Local variables for Transfer Controller */
-/* --------------------------------------- */
-
-/* This is a circular (double-linked) list of the active urbs for each epid.
-   The head is never removed, and new urbs are linked onto the list as
-   urb_entry_t elements. Don't reference urb_list directly; use the wrapper
-   functions instead (which includes spin_locks) */
-static struct list_head urb_list[NBR_OF_EPIDS];
-
-/* Read about the need and usage of this lock in submit_ctrl_urb. */
-/* Lock for URB lists for each EPID */
-static spinlock_t urb_list_lock;
-
-/* Lock for EPID array register (R_USB_EPT_x) in Etrax */
-static spinlock_t etrax_epid_lock;
-
-/* Lock for dma8 sub0 handling */
-static spinlock_t etrax_dma8_sub0_lock;
-
-/* DMA IN cache bug. Align the DMA IN buffers to 32 bytes, i.e. a cache line.
-   Since RX_DESC_BUF_SIZE is 1024 is a multiple of 32, all rx buffers will be
-   cache aligned. */
-static volatile unsigned char RxBuf[RX_BUF_SIZE] __attribute__ ((aligned (32)));
-static volatile struct USB_IN_Desc RxDescList[NBR_OF_RX_DESC] __attribute__ ((aligned (4)));
-
-/* Pointers into RxDescList. */
-static volatile struct USB_IN_Desc *myNextRxDesc;
-static volatile struct USB_IN_Desc *myLastRxDesc;
-
-/* A zout transfer makes a memory access at the address of its buf pointer,
-   which means that setting this buf pointer to 0 will cause an access to the
-   flash. In addition to this, setting sw_len to 0 results in a 16/32 bytes
-   (depending on DMA burst size) transfer.
-   Instead, we set it to 1, and point it to this buffer. */
-static int zout_buffer[4] __attribute__ ((aligned (4)));
-
-/* Cache for allocating new EP and SB descriptors. */
-static struct kmem_cache *usb_desc_cache;
-
-/* Cache for the data allocated in the isoc descr top half. */
-static struct kmem_cache *isoc_compl_cache;
-
-/* Cache for the data allocated when delayed finishing of URBs */
-static struct kmem_cache *later_data_cache;
-
-
-/* Counter to keep track of how many Isoc EP we have sat up. Used to enable
-   and disable iso_eof interrupt. We only need these interrupts when we have
-   Isoc data endpoints (consumes CPU cycles).
-   FIXME: This could be more fine granular, so this interrupt is only enabled
-   when we have a In Isoc URB not URB_ISO_ASAP flaged queued. */
-static int isoc_epid_counter;
-
-/* Protecting wrapper functions for R_USB_EPT_x */
-/* -------------------------------------------- */
-static inline void etrax_epid_set(__u8 index, __u32 data) {
-  unsigned long flags;
-  spin_lock_irqsave(&etrax_epid_lock, flags);
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
-  nop();
-  *R_USB_EPT_DATA = data;
-  spin_unlock_irqrestore(&etrax_epid_lock, flags);
-}
-
-static inline void etrax_epid_clear_error(__u8 index) {
-  unsigned long flags;
-  spin_lock_irqsave(&etrax_epid_lock, flags);
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
-  nop();
-  *R_USB_EPT_DATA &=
-    ~(IO_MASK(R_USB_EPT_DATA, error_count_in) |
-      IO_MASK(R_USB_EPT_DATA, error_count_out) |
-      IO_MASK(R_USB_EPT_DATA, error_code));
-  spin_unlock_irqrestore(&etrax_epid_lock, flags);
-}
-
-static inline void etrax_epid_set_toggle(__u8 index, __u8 dirout,
-                                             __u8 toggle) {
-  unsigned long flags;
-  spin_lock_irqsave(&etrax_epid_lock, flags);
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
-  nop();
-  if(dirout) {
-    *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_out);
-    *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_out, toggle);
-  } else {
-    *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_in);
-    *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_in, toggle);
-  }
-  spin_unlock_irqrestore(&etrax_epid_lock, flags);
-}
-
-static inline __u8 etrax_epid_get_toggle(__u8 index, __u8 dirout) {
-  unsigned long flags;
-  __u8 toggle;
-  spin_lock_irqsave(&etrax_epid_lock, flags);
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
-  nop();
-  if (dirout) {
-    toggle = IO_EXTRACT(R_USB_EPT_DATA, t_out, *R_USB_EPT_DATA);
-  } else {
-    toggle = IO_EXTRACT(R_USB_EPT_DATA, t_in, *R_USB_EPT_DATA);
-  }
-  spin_unlock_irqrestore(&etrax_epid_lock, flags);
-  return toggle;
-}
-
-
-static inline __u32 etrax_epid_get(__u8 index) {
-  unsigned long flags;
-  __u32 data;
-  spin_lock_irqsave(&etrax_epid_lock, flags);
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
-  nop();
-  data = *R_USB_EPT_DATA;
-  spin_unlock_irqrestore(&etrax_epid_lock, flags);
-  return data;
-}
-
-
-
-
-/* Main functions for Transfer Controller */
-/* -------------------------------------- */
-
-/* Init structs, memories and lists used by Transfer Controller */
-int tc_init(struct usb_hcd *hcd) {
-  int i;
-  /* Clear software state info for all epids */
-  memset(epid_state, 0, sizeof(struct etrax_epid) * NBR_OF_EPIDS);
-
-  /* Set Invalid and Dummy as being in use and disabled */
-  epid_state[INVALID_EPID].inuse = 1;
-  epid_state[DUMMY_EPID].inuse = 1;
-  epid_state[INVALID_EPID].disabled = 1;
-  epid_state[DUMMY_EPID].disabled = 1;
-
-  /* Clear counter for how many Isoc epids we have sat up */
-  isoc_epid_counter = 0;
-
-  /* Initialize the urb list by initiating a head for each list.
-     Also reset list hodling active URB for each epid */
-  for (i = 0; i < NBR_OF_EPIDS; i++) {
-    INIT_LIST_HEAD(&urb_list[i]);
-    activeUrbList[i] = NULL;
-  }
-
-  /* Init lock for URB lists */
-  spin_lock_init(&urb_list_lock);
-  /* Init lock for Etrax R_USB_EPT register */
-  spin_lock_init(&etrax_epid_lock);
-  /* Init lock for Etrax dma8 sub0 handling */
-  spin_lock_init(&etrax_dma8_sub0_lock);
-
-  /* We use kmem_cache_* to make sure that all DMA desc. are dword aligned */
-
-  /* Note that we specify sizeof(struct USB_EP_Desc) as the size, but also
-     allocate SB descriptors from this cache. This is ok since
-     sizeof(struct USB_EP_Desc) == sizeof(struct USB_SB_Desc). */
-  usb_desc_cache = kmem_cache_create("usb_desc_cache",
-				     sizeof(struct USB_EP_Desc), 0,
-				     SLAB_HWCACHE_ALIGN, 0);
-  if(usb_desc_cache == NULL) {
-    return -ENOMEM;
-  }
-
-  /* Create slab cache for speedy allocation of memory for isoc bottom-half
-     interrupt handling */
-  isoc_compl_cache =
-    kmem_cache_create("isoc_compl_cache",
-		      sizeof(struct crisv10_isoc_complete_data),
-		      0, SLAB_HWCACHE_ALIGN, 0);
-  if(isoc_compl_cache == NULL) {
-    return -ENOMEM;
-  }
-
-  /* Create slab cache for speedy allocation of memory for later URB finish
-     struct */
-  later_data_cache =
-    kmem_cache_create("later_data_cache",
-		      sizeof(struct urb_later_data),
-		      0, SLAB_HWCACHE_ALIGN, 0);
-  if(later_data_cache == NULL) {
-    return -ENOMEM;
-  }
-
-
-  /* Initiate the bulk start timer. */
-  init_timer(&bulk_start_timer);
-  bulk_start_timer.expires = jiffies + BULK_START_TIMER_INTERVAL;
-  bulk_start_timer.function = tc_bulk_start_timer_func;
-  add_timer(&bulk_start_timer);
-
-
-  /* Initiate the bulk eot timer. */
-  init_timer(&bulk_eot_timer);
-  bulk_eot_timer.expires = jiffies + BULK_EOT_TIMER_INTERVAL;
-  bulk_eot_timer.function = tc_bulk_eot_timer_func;
-  bulk_eot_timer.data = (unsigned long)hcd;
-  add_timer(&bulk_eot_timer);
-
-  return 0;
-}
-
-/* Uninitialize all resources used by Transfer Controller */
-void tc_destroy(void) {
-
-  /* Destroy all slab cache */
-  kmem_cache_destroy(usb_desc_cache);
-  kmem_cache_destroy(isoc_compl_cache);
-  kmem_cache_destroy(later_data_cache);
-
-  /* Remove timers */
-  del_timer(&bulk_start_timer);
-  del_timer(&bulk_eot_timer);
-}
-
-static void restart_dma8_sub0(void) {
-  unsigned long flags;
-  spin_lock_irqsave(&etrax_dma8_sub0_lock, flags);
-  /* Verify that the dma is not running */
-  if ((*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd)) == 0) {
-    struct USB_EP_Desc *ep = (struct USB_EP_Desc *)phys_to_virt(*R_DMA_CH8_SUB0_EP);
-    while (DUMMY_EPID == IO_EXTRACT(USB_EP_command, epid, ep->command)) {
-      ep = (struct USB_EP_Desc *)phys_to_virt(ep->next);
-    }
-    /* Advance the DMA to the next EP descriptor that is not a DUMMY_EPID. */
-    *R_DMA_CH8_SUB0_EP = virt_to_phys(ep);
-    /* Restart the DMA */
-    *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start);
-  }
-  spin_unlock_irqrestore(&etrax_dma8_sub0_lock, flags);
-}
-
-/* queue an URB with the transfer controller (called from hcd_driver) */
-static int tc_urb_enqueue(struct usb_hcd *hcd, 
-			  struct urb *urb, 
-			  gfp_t mem_flags) {
-  int epid;
-  int retval;
-  int bustime = 0;
-  int maxpacket;
-  unsigned long flags;
-  struct crisv10_urb_priv *urb_priv;
-  struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd);
-  DBFENTER;
-
-  if(!(crisv10_hcd->running)) {
-    /* The USB Controller is not running, probably because no device is 
-       attached. No idea to enqueue URBs then */
-    tc_warn("Rejected enqueueing of URB:0x%x because no dev attached\n",
-	    (unsigned int)urb);
-    return -ENOENT;
-  }
-
-  maxpacket = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe));
-  /* Special case check for In Isoc transfers. Specification states that each
-     In Isoc transfer consists of one packet and therefore it should fit into
-     the transfer-buffer of an URB.
-     We do the check here to be sure (an invalid scenario can be produced with
-     parameters to the usbtest suite) */
-  if(usb_pipeisoc(urb->pipe) && usb_pipein(urb->pipe) &&
-     (urb->transfer_buffer_length < maxpacket)) {
-    tc_err("Submit In Isoc URB with buffer length:%d to pipe with maxpacketlen: %d\n", urb->transfer_buffer_length, maxpacket);
-    return -EMSGSIZE;
-  }
-
-  /* Check if there is a epid for URBs destination, if not this function
-     set up one. */
-  epid = tc_setup_epid(urb->ep, urb, mem_flags);
-  if (epid < 0) {
-    tc_err("Failed setup epid:%d for URB:0x%x\n", epid, (unsigned int)urb);
-    DBFEXIT;
-    return -ENOMEM;
-  }
-
-  if(urb == activeUrbList[epid]) {
-    tc_err("Resubmition of allready active URB:0x%x\n", (unsigned int)urb);
-    return -ENXIO;
-  }
-
-  if(urb_list_entry(urb, epid)) {
-    tc_err("Resubmition of allready queued URB:0x%x\n", (unsigned int)urb);
-    return -ENXIO;
-  }
-
-  /* If we actively have flaged endpoint as disabled then refuse submition */
-  if(epid_state[epid].disabled) {
-    return -ENOENT;
-  }
-
-  /* Allocate and init HC-private data for URB */
-  if(urb_priv_create(hcd, urb, epid, mem_flags) != 0) {
-    DBFEXIT;
-    return -ENOMEM;
-  }
-  urb_priv = urb->hcpriv;
-
-  /* Check if there is enough bandwidth for periodic transfer  */
-  if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe)) {
-    /* only check (and later claim) if not already claimed */
-    if (urb_priv->bandwidth == 0) {
-      bustime = crisv10_usb_check_bandwidth(urb->dev, urb);
-      if (bustime < 0) {
-        tc_err("Not enough periodic bandwidth\n");
-        urb_priv_free(hcd, urb);
-        DBFEXIT;
-        return -ENOSPC;
-      }
-    }
-  }
-
-  tc_dbg("Enqueue URB:0x%x[%d] epid:%d (%s) bufflen:%d\n",
-	 (unsigned int)urb, urb_priv->urb_num, epid,
-	 pipe_to_str(urb->pipe), urb->transfer_buffer_length);
-
-  /* Create and link SBs required for this URB */
-  retval = create_sb_for_urb(urb, mem_flags);
-  if(retval != 0) {
-    tc_err("Failed to create SBs for URB:0x%x[%d]\n", (unsigned int)urb,
-	   urb_priv->urb_num);
-    urb_priv_free(hcd, urb);
-    DBFEXIT;
-    return retval;
-  }
-
-  /* Init intr EP pool if this URB is a INTR transfer. This pool is later
-     used when inserting EPs in the TxIntrEPList. We do the alloc here
-     so we can't run out of memory later */
-  if(usb_pipeint(urb->pipe)) {
-    retval = init_intr_urb(urb, mem_flags);
-    if(retval != 0) {
-      tc_warn("Failed to init Intr URB\n");
-      urb_priv_free(hcd, urb);
-      DBFEXIT;
-      return retval;
-    }
-  }
-
-  /* Disable other access when inserting USB */
-  local_irq_save(flags);
-
-  /* Claim bandwidth, if needed */
-  if(bustime) {
-    crisv10_usb_claim_bandwidth(urb->dev,
-                                urb,
-                                bustime,
-                                (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS));
-  }
-  
-  /* Add URB to EP queue */
-  urb_list_add(urb, epid, mem_flags);
-
-  if(usb_pipeisoc(urb->pipe)) {
-    /* Special processing of Isoc URBs. */
-    tc_dma_process_isoc_urb(urb);
-  } else {
-    /* Process EP queue for rest of the URB types (Bulk, Ctrl, Intr) */
-    tc_dma_process_queue(epid);
-  }
-
-  local_irq_restore(flags);
-
-  DBFEXIT;
-  return 0;
-}
-
-/* remove an URB from the transfer controller queues (called from hcd_driver)*/
-static int tc_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) {
-  struct crisv10_urb_priv *urb_priv;
-  unsigned long flags;
-  int epid;
-
-  DBFENTER;
-  /* Disable interrupts here since a descriptor interrupt for the isoc epid
-     will modify the sb list.  This could possibly be done more granular, but
-     urb_dequeue should not be used frequently anyway.
-  */
-  local_irq_save(flags);
-
-  urb->status = status;
-  urb_priv = urb->hcpriv;
-
-  if (!urb_priv) {
-    /* This happens if a device driver calls unlink on an urb that
-       was never submitted (lazy driver) or if the urb was completed
-       while dequeue was being called. */
-    tc_warn("Dequeing of not enqueued URB:0x%x\n", (unsigned int)urb);
-    local_irq_restore(flags);
-    return 0;
-  }
-  epid = urb_priv->epid;
-
-  tc_warn("Dequeing %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n",
-	  (urb == activeUrbList[epid]) ? "active" : "queued",
-	  (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
-	  str_type(urb->pipe), epid, urb->status,
-	  (urb_priv->later_data) ? "later-sched" : "");
-
-  /* For Bulk, Ctrl and Intr are only one URB active at a time. So any URB
-     that isn't active can be dequeued by just removing it from the queue */
-  if(usb_pipebulk(urb->pipe) || usb_pipecontrol(urb->pipe) ||
-     usb_pipeint(urb->pipe)) {
-
-    /* Check if URB haven't gone further than the queue */
-    if(urb != activeUrbList[epid]) {
-      ASSERT(urb_priv->later_data == NULL);
-      tc_warn("Dequeing URB:0x%x[%d] (%s %s epid:%d) from queue"
-	      " (not active)\n", (unsigned int)urb, urb_priv->urb_num,
-	      str_dir(urb->pipe), str_type(urb->pipe), epid);
-      
-      /* Finish the URB with error status from USB core */
-      tc_finish_urb(hcd, urb, urb->status);
-      local_irq_restore(flags);
-      return 0;
-    }
-  }
-
-  /* Set URB status to Unlink for handling when interrupt comes. */
-  urb_priv->urb_state = UNLINK;
-
-  /* Differentiate dequeing of Bulk and Ctrl from Isoc and Intr */
-  switch(usb_pipetype(urb->pipe)) {
-  case PIPE_BULK:
-    /* Check if EP still is enabled */
-    if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-      /* The EP was enabled, disable it. */
-      TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-    }
-    /* Kicking dummy list out of the party. */
-    TxBulkEPList[epid].next = virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]);
-    break;
-  case PIPE_CONTROL:
-    /* Check if EP still is enabled */
-    if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-      /* The EP was enabled, disable it. */
-      TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-    }
-    break;
-  case PIPE_ISOCHRONOUS:
-    /* Disabling, busy-wait and unlinking of Isoc SBs will be done in
-       finish_isoc_urb(). Because there might the case when URB is dequeued
-       but there are other valid URBs waiting */
-
-    /* Check if In Isoc EP still is enabled */
-    if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-      /* The EP was enabled, disable it. */
-      TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-    }
-    break;
-  case PIPE_INTERRUPT:
-    /* Special care is taken for interrupt URBs. EPs are unlinked in
-       tc_finish_urb */
-    break;
-  default:
-    break;
-  }
-
-  /* Asynchronous unlink, finish the URB later from scheduled or other
-     event (data finished, error) */
-  tc_finish_urb_later(hcd, urb, urb->status);
-
-  local_irq_restore(flags);
-  DBFEXIT;
-  return 0;
-}
-
-
-static void tc_sync_finish_epid(struct usb_hcd *hcd, int epid) {
-  volatile int timeout = 10000;
-  struct urb* urb;
-  struct crisv10_urb_priv* urb_priv;
-  unsigned long flags;
-  
-  volatile struct USB_EP_Desc *first_ep;  /* First EP in the list. */
-  volatile struct USB_EP_Desc *curr_ep;   /* Current EP, the iterator. */
-  volatile struct USB_EP_Desc *next_ep;   /* The EP after current. */
-
-  int type = epid_state[epid].type;
-
-  /* Setting this flag will cause enqueue() to return -ENOENT for new
-     submitions on this endpoint and finish_urb() wont process queue further */
-  epid_state[epid].disabled = 1;
-
-  switch(type) {
-  case PIPE_BULK:
-    /* Check if EP still is enabled */
-    if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-      /* The EP was enabled, disable it. */
-      TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-      tc_warn("sync_finish: Disabling EP for epid:%d\n", epid);
-
-      /* Do busy-wait until DMA not using this EP descriptor anymore */
-      while((*R_DMA_CH8_SUB0_EP ==
-	     virt_to_phys(&TxBulkEPList[epid])) &&
-	    (timeout-- > 0));
-      if(timeout == 0) {
-	warn("Timeout while waiting for DMA-TX-Bulk to leave EP for"
-	     " epid:%d\n", epid);
-      }
-    }
-    break;
-
-  case PIPE_CONTROL:
-    /* Check if EP still is enabled */
-    if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-      /* The EP was enabled, disable it. */
-      TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-      tc_warn("sync_finish: Disabling EP for epid:%d\n", epid);
-
-      /* Do busy-wait until DMA not using this EP descriptor anymore */
-      while((*R_DMA_CH8_SUB1_EP ==
-	     virt_to_phys(&TxCtrlEPList[epid])) &&
-	    (timeout-- > 0));
-      if(timeout == 0) {
-	warn("Timeout while waiting for DMA-TX-Ctrl to leave EP for"
-	     " epid:%d\n", epid);
-      }
-    }
-    break;
-
-  case PIPE_INTERRUPT:
-    local_irq_save(flags);
-    /* Disable all Intr EPs belonging to epid */
-    first_ep = &TxIntrEPList[0];
-    curr_ep = first_ep;
-    do {
-      next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
-      if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) {
-	/* Disable EP */
-	next_ep->command &= ~IO_MASK(USB_EP_command, enable);
-      }
-      curr_ep = phys_to_virt(curr_ep->next);
-    } while (curr_ep != first_ep);
-
-    local_irq_restore(flags);
-    break;
-
-  case PIPE_ISOCHRONOUS:
-    /* Check if EP still is enabled */
-    if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-      tc_warn("sync_finish: Disabling Isoc EP for epid:%d\n", epid);
-      /* The EP was enabled, disable it. */
-      TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-      
-      while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) &&
-	    (timeout-- > 0));
-      if(timeout == 0) {
-	warn("Timeout while waiting for DMA-TX-Isoc to leave EP for"
-	     " epid:%d\n", epid);
-      }
-    }
-    break;
-  }
-
-  local_irq_save(flags);
-
-  /* Finish if there is active URB for this endpoint */
-  if(activeUrbList[epid] != NULL) {
-    urb = activeUrbList[epid];
-    urb_priv = urb->hcpriv;
-    ASSERT(urb_priv);
-    tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n",
-	    (urb == activeUrbList[epid]) ? "active" : "queued",
-	    (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
-	    str_type(urb->pipe), epid, urb->status,
-	    (urb_priv->later_data) ? "later-sched" : "");
-
-    tc_finish_urb(hcd, activeUrbList[epid], -ENOENT);
-    ASSERT(activeUrbList[epid] == NULL);
-  }
-
-  /* Finish any queued URBs for this endpoint. There won't be any resubmitions
-     because epid_disabled causes enqueue() to fail for this endpoint */
-  while((urb = urb_list_first(epid)) != NULL) {
-    urb_priv = urb->hcpriv;
-    ASSERT(urb_priv);
-
-    tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n",
-	    (urb == activeUrbList[epid]) ? "active" : "queued",
-	    (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
-	    str_type(urb->pipe), epid, urb->status,
-	    (urb_priv->later_data) ? "later-sched" : "");
-
-    tc_finish_urb(hcd, urb, -ENOENT);
-  }
-  epid_state[epid].disabled = 0;
-  local_irq_restore(flags);
-}
-
-/* free resources associated with an endpoint (called from hcd_driver) */
-static void tc_endpoint_disable(struct usb_hcd *hcd, 
-				struct usb_host_endpoint *ep) {
-  DBFENTER;
-  /* Only free epid if it has been allocated. We get two endpoint_disable
-     requests for ctrl endpoints so ignore the second one */
-  if(ep->hcpriv != NULL) {
-    struct crisv10_ep_priv *ep_priv = ep->hcpriv;
-    int epid = ep_priv->epid;
-    tc_warn("endpoint_disable ep:0x%x ep-priv:0x%x (%s) (epid:%d freed)\n",
-	   (unsigned int)ep, (unsigned int)ep->hcpriv,
-	   endpoint_to_str(&(ep->desc)), epid);
-
-    tc_sync_finish_epid(hcd, epid);
-
-    ASSERT(activeUrbList[epid] == NULL);
-    ASSERT(list_empty(&urb_list[epid]));
-
-    tc_free_epid(ep);
-  } else {
-    tc_dbg("endpoint_disable ep:0x%x ep-priv:0x%x (%s)\n", (unsigned int)ep,
-	   (unsigned int)ep->hcpriv, endpoint_to_str(&(ep->desc)));
-  }
-  DBFEXIT;
-}
-
-static void tc_finish_urb_later_proc(struct work_struct* work) {
-  unsigned long flags;
-  struct urb_later_data* uld;
-
-  local_irq_save(flags);
-  uld = container_of(work, struct urb_later_data, dws.work);
-  if(uld->urb == NULL) {
-    late_dbg("Later finish of URB = NULL (allready finished)\n");
-  } else {
-    struct crisv10_urb_priv* urb_priv = uld->urb->hcpriv;
-    ASSERT(urb_priv);
-    if(urb_priv->urb_num == uld->urb_num) {
-      late_dbg("Later finish of URB:0x%x[%d]\n", (unsigned int)(uld->urb),
-	       urb_priv->urb_num);
-      if(uld->status != uld->urb->status) {
-	errno_dbg("Later-finish URB with status:%d, later-status:%d\n",
-		  uld->urb->status, uld->status);
-      }
-      if(uld != urb_priv->later_data) {
-	panic("Scheduled uld not same as URBs uld\n");
-      }
-      tc_finish_urb(uld->hcd, uld->urb, uld->status);
-    } else {
-      late_warn("Ignoring later finish of URB:0x%x[%d]"
-		", urb_num doesn't match current URB:0x%x[%d]",
-		(unsigned int)(uld->urb), uld->urb_num,
-		(unsigned int)(uld->urb), urb_priv->urb_num);
-    }
-  }
-  local_irq_restore(flags);
-  kmem_cache_free(later_data_cache, uld);
-}
-
-static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb,
-				int status) {
-  struct crisv10_urb_priv *urb_priv = urb->hcpriv;
-  struct urb_later_data* uld;
-
-  ASSERT(urb_priv);
-
-  if(urb_priv->later_data != NULL) {
-    /* Later-finish allready scheduled for this URB, just update status to
-       return when finishing later */
-    errno_dbg("Later-finish schedule change URB status:%d with new"
-	      " status:%d\n", urb_priv->later_data->status, status);
-    
-    urb_priv->later_data->status = status;
-    return;
-  }
-
-  uld = kmem_cache_alloc(later_data_cache, GFP_ATOMIC);
-  ASSERT(uld);
-
-  uld->hcd = hcd;
-  uld->urb = urb;
-  uld->urb_num = urb_priv->urb_num;
-  uld->status = status;
-
-  INIT_DELAYED_WORK(&uld->dws, tc_finish_urb_later_proc);
-  urb_priv->later_data = uld;
-
-  /* Schedule the finishing of the URB to happen later */
-  schedule_delayed_work(&uld->dws, LATER_TIMER_DELAY);
-}
-
-static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb,
-			       int status);
-
-static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status) {
-  struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd);
-  struct crisv10_urb_priv *urb_priv = urb->hcpriv;
-  int epid;
-  char toggle;
-  int urb_num;
-
-  DBFENTER;
-  ASSERT(urb_priv != NULL);
-  epid = urb_priv->epid;
-  urb_num = urb_priv->urb_num;
-
-  if(urb != activeUrbList[epid]) {
-    if(urb_list_entry(urb, epid)) {
-      /* Remove this URB from the list. Only happens when URB are finished
-	 before having been processed (dequeing) */
-      urb_list_del(urb, epid);
-    } else {
-      tc_warn("Finishing of URB:0x%x[%d] neither active or in queue for"
-	      " epid:%d\n", (unsigned int)urb, urb_num, epid);
-    }
-  }
-
-  /* Cancel any pending later-finish of this URB */
-  if(urb_priv->later_data) {
-    urb_priv->later_data->urb = NULL;
-  }
-
-  /* For an IN pipe, we always set the actual length, regardless of whether
-     there was an error or not (which means the device driver can use the data
-     if it wants to). */
-  if(usb_pipein(urb->pipe)) {
-    urb->actual_length = urb_priv->rx_offset;
-  } else {
-    /* Set actual_length for OUT urbs also; the USB mass storage driver seems
-       to want that. */
-    if (status == 0 && urb->status == -EINPROGRESS) {
-      urb->actual_length = urb->transfer_buffer_length;
-    } else {
-      /*  We wouldn't know of any partial writes if there was an error. */
-      urb->actual_length = 0;
-    }
-  }
-
-
-  /* URB status mangling */
-  if(urb->status == -EINPROGRESS) {
-    /* The USB core hasn't changed the status, let's set our finish status */
-    urb->status = status;
-
-    if ((status == 0) && (urb->transfer_flags & URB_SHORT_NOT_OK) &&
-	usb_pipein(urb->pipe) &&
-	(urb->actual_length != urb->transfer_buffer_length)) {
-      /* URB_SHORT_NOT_OK means that short reads (shorter than the endpoint's
-	 max length) is to be treated as an error. */
-      errno_dbg("Finishing URB:0x%x[%d] with SHORT_NOT_OK flag and short"
-		" data:%d\n", (unsigned int)urb, urb_num,
-		urb->actual_length);
-      urb->status = -EREMOTEIO;
-    }
-
-    if(urb_priv->urb_state == UNLINK) {
-      /* URB has been requested to be unlinked asynchronously */
-      urb->status = -ECONNRESET;
-      errno_dbg("Fixing unlink status of URB:0x%x[%d] to:%d\n",
-		(unsigned int)urb, urb_num, urb->status);
-    }
-  } else {
-    /* The USB Core wants to signal some error via the URB, pass it through */
-  }
-
-  /* use completely different finish function for Isoc URBs */
-  if(usb_pipeisoc(urb->pipe)) {
-    tc_finish_isoc_urb(hcd, urb, status);
-    return;
-  }
-
-  /* Do special unlinking of EPs for Intr traffic */
-  if(usb_pipeint(urb->pipe)) {
-    tc_dma_unlink_intr_urb(urb);
-  }
-
-  /* Release allocated bandwidth for periodic transfers */
-  if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe))
-    crisv10_usb_release_bandwidth(hcd,
-                                  usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS,
-                                  urb_priv->bandwidth);
-
-  /* This URB is active on EP */
-  if(urb == activeUrbList[epid]) {
-    /* We need to fiddle with the toggle bits because the hardware doesn't do
-       it for us. */
-    toggle = etrax_epid_get_toggle(epid, usb_pipeout(urb->pipe));
-    usb_settoggle(urb->dev, usb_pipeendpoint(urb->pipe),
-		  usb_pipeout(urb->pipe), toggle);
-
-    /* Checks for Ctrl and Bulk EPs */
-    switch(usb_pipetype(urb->pipe)) {
-    case PIPE_BULK:
-      /* Check so Bulk EP realy is disabled before finishing active URB  */
-      ASSERT((TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) ==
-	     IO_STATE(USB_EP_command, enable, no));
-      /* Disable sub-pointer for EP to avoid next tx_interrupt() to
-	 process Bulk EP. */
-      TxBulkEPList[epid].sub = 0;
-      /* No need to wait for the DMA before changing the next pointer.
-	 The modulo NBR_OF_EPIDS isn't actually necessary, since we will never use
-	 the last one (INVALID_EPID) for actual traffic. */
-      TxBulkEPList[epid].next = 
-	virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]);
-      break;
-    case PIPE_CONTROL:
-      /* Check so Ctrl EP realy is disabled before finishing active URB  */
-      ASSERT((TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) ==
-	     IO_STATE(USB_EP_command, enable, no));
-      /* Disable sub-pointer for EP to avoid next tx_interrupt() to
-	 process Ctrl EP. */
-      TxCtrlEPList[epid].sub = 0;
-      break;
-    }
-  }
-
-  /* Free HC-private URB data*/
-  urb_priv_free(hcd, urb);
-
-  if(urb->status) {
-    errno_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n",
-	      (unsigned int)urb, urb_num, str_dir(urb->pipe),
-	      str_type(urb->pipe), urb->actual_length, urb->status);
-  } else {
-    tc_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n",
-	   (unsigned int)urb, urb_num, str_dir(urb->pipe),
-	   str_type(urb->pipe), urb->actual_length, urb->status);
-  }
-
-  /* If we just finished an active URB, clear active pointer. */
-  if (urb == activeUrbList[epid]) {
-    /* Make URB not active on EP anymore */
-    activeUrbList[epid] = NULL;
-
-    if(urb->status == 0) {
-      /* URB finished sucessfully, process queue to see if there are any more
-	 URBs waiting before we call completion function.*/
-      if(crisv10_hcd->running) {
-	/* Only process queue if USB controller is running */
-	tc_dma_process_queue(epid);
-      } else {
-	tc_warn("No processing of queue for epid:%d, USB Controller not"
-		" running\n", epid);
-      }
-    }
-  }
-
-  /*  Hand the URB from HCD to its USB device driver, using its completion
-      functions */
-  usb_hcd_giveback_urb (hcd, urb, status);
-
-  /* Check the queue once more if the URB returned with error, because we
-     didn't do it before the completion function because the specification
-     states that the queue should not restart until all it's unlinked
-     URBs have been fully retired, with the completion functions run */
-  if(crisv10_hcd->running) {
-    /* Only process queue if USB controller is running */
-    tc_dma_process_queue(epid);
-  } else {
-    tc_warn("No processing of queue for epid:%d, USB Controller not running\n",
-	    epid);
-  }
-
-  DBFEXIT;
-}
-
-static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb,
-			       int status) {
-  struct crisv10_urb_priv *urb_priv = urb->hcpriv;
-  int epid, i;
-  volatile int timeout = 10000;
-  int bandwidth = 0;
-
-  ASSERT(urb_priv);
-  epid = urb_priv->epid;
-
-  ASSERT(usb_pipeisoc(urb->pipe));
-
-  /* Set that all isoc packets have status and length set before
-     completing the urb. */
-  for (i = urb_priv->isoc_packet_counter; i < urb->number_of_packets; i++){
-    urb->iso_frame_desc[i].actual_length = 0;
-    urb->iso_frame_desc[i].status = -EPROTO;
-  }
-
-  /* Check if the URB is currently active (done or error) */
-  if(urb == activeUrbList[epid]) {
-    /* Check if there are another In Isoc URB queued for this epid */
-    if (!list_empty(&urb_list[epid])&& !epid_state[epid].disabled) {
-      /* Move it from queue to active and mark it started so Isoc transfers
-	 won't be interrupted.
-	 All Isoc URBs data transfers are already added to DMA lists so we
-	 don't have to insert anything in DMA lists here. */
-      activeUrbList[epid] = urb_list_first(epid);
-      ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_state =
-	STARTED;
-      urb_list_del(activeUrbList[epid], epid);
-
-      if(urb->status) {
-	errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)"
-		  " status:%d, new waiting URB:0x%x[%d]\n",
-		  (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
-		  str_type(urb->pipe), urb_priv->isoc_packet_counter,
-		  urb->number_of_packets, urb->status,
-		  (unsigned int)activeUrbList[epid],
-		  ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_num);
-      }
-
-    } else { /* No other URB queued for this epid */
-      if(urb->status) {
-	errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)"
-		  " status:%d, no new URB waiting\n",
-		  (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
-		  str_type(urb->pipe), urb_priv->isoc_packet_counter,
-		  urb->number_of_packets, urb->status);
-      }
-
-      /* Check if EP is still enabled, then shut it down. */
-      if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-	isoc_dbg("Isoc EP enabled for epid:%d, disabling it\n", epid);
-
-	/* Should only occur for In Isoc EPs where SB isn't consumed. */
-	ASSERT(usb_pipein(urb->pipe));
-
-	/* Disable it and wait for it to stop */
-	TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-	
-	/* Ah, the luxury of busy-wait. */
-	while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) &&
-	      (timeout-- > 0));
-	if(timeout == 0) {
-	  warn("Timeout while waiting for DMA-TX-Isoc to leave EP for epid:%d\n", epid);
-	}
-      }
-
-      /* Unlink SB to say that epid is finished. */
-      TxIsocEPList[epid].sub = 0;
-      TxIsocEPList[epid].hw_len = 0;
-
-      /* No URB active for EP anymore */
-      activeUrbList[epid] = NULL;
-    }
-  } else { /* Finishing of not active URB (queued up with SBs thought) */
-    isoc_warn("finish_isoc_urb (URB:0x%x %s) (%d of %d packets) status:%d,"
-	      " SB queued but not active\n",
-	      (unsigned int)urb, str_dir(urb->pipe),
-	      urb_priv->isoc_packet_counter, urb->number_of_packets,
-	      urb->status);
-    if(usb_pipeout(urb->pipe)) {
-      /* Finishing of not yet active Out Isoc URB needs unlinking of SBs. */
-      struct USB_SB_Desc *iter_sb, *prev_sb, *next_sb;
-
-      iter_sb = TxIsocEPList[epid].sub ?
-	phys_to_virt(TxIsocEPList[epid].sub) : 0;
-      prev_sb = 0;
-
-      /* SB that is linked before this URBs first SB */
-      while (iter_sb && (iter_sb != urb_priv->first_sb)) {
-	prev_sb = iter_sb;
-	iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0;
-      }
-
-      if (iter_sb == 0) {
-	/* Unlink of the URB currently being transmitted. */
-	prev_sb = 0;
-	iter_sb = TxIsocEPList[epid].sub ? phys_to_virt(TxIsocEPList[epid].sub) : 0;
-      }
-
-      while (iter_sb && (iter_sb != urb_priv->last_sb)) {
-	iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0;
-      }
-
-      if (iter_sb) {
-	next_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0;
-      } else {
-	/* This should only happen if the DMA has completed
-	   processing the SB list for this EP while interrupts
-	   are disabled. */
-	isoc_dbg("Isoc urb not found, already sent?\n");
-	next_sb = 0;
-      }
-      if (prev_sb) {
-	prev_sb->next = next_sb ? virt_to_phys(next_sb) : 0;
-      } else {
-	TxIsocEPList[epid].sub = next_sb ? virt_to_phys(next_sb) : 0;
-      }
-    }
-  }
-
-  /* Free HC-private URB data*/
-  bandwidth = urb_priv->bandwidth;
-  urb_priv_free(hcd, urb);
-
-  crisv10_usb_release_bandwidth(hcd, usb_pipeisoc(urb->pipe), bandwidth);
-
-  /*  Hand the URB from HCD to its USB device driver, using its completion
-      functions */
-  usb_hcd_giveback_urb (hcd, urb, status);
-}
-
-static __u32 urb_num = 0;
-
-/* allocate and initialize URB private data */
-static int urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid,
-			   int mem_flags) {
-  struct crisv10_urb_priv *urb_priv;
-  
-  urb_priv = kmalloc(sizeof *urb_priv, mem_flags);
-  if (!urb_priv)
-    return -ENOMEM;
-  memset(urb_priv, 0, sizeof *urb_priv);
-
-  urb_priv->epid = epid;
-  urb_priv->urb_state = NOT_STARTED;
-
-  urb->hcpriv = urb_priv;
-  /* Assign URB a sequence number, and increment counter */
-  urb_priv->urb_num = urb_num;
-  urb_num++;
-  urb_priv->bandwidth = 0;
-  return 0;
-}
-
-/* free URB private data */
-static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb) {
-  int i;
-  struct crisv10_urb_priv *urb_priv = urb->hcpriv;
-  ASSERT(urb_priv != 0);
-
-  /* Check it has any SBs linked that needs to be freed*/
-  if(urb_priv->first_sb != NULL) {
-    struct USB_SB_Desc *next_sb, *first_sb, *last_sb;
-    int i = 0;
-    first_sb = urb_priv->first_sb;
-    last_sb = urb_priv->last_sb;
-    ASSERT(last_sb);
-    while(first_sb != last_sb) {
-      next_sb = (struct USB_SB_Desc *)phys_to_virt(first_sb->next);
-      kmem_cache_free(usb_desc_cache, first_sb);
-      first_sb = next_sb;
-      i++;
-    }
-    kmem_cache_free(usb_desc_cache, last_sb);
-    i++;
-  }
-
-  /* Check if it has any EPs in its Intr pool that also needs to be freed */
-  if(urb_priv->intr_ep_pool_length > 0) {
-    for(i = 0; i < urb_priv->intr_ep_pool_length; i++) {
-      kfree(urb_priv->intr_ep_pool[i]);
-    }
-    /*
-    tc_dbg("Freed %d EPs from URB:0x%x EP pool\n",
-	     urb_priv->intr_ep_pool_length, (unsigned int)urb);
-    */
-  }
-
-  kfree(urb_priv);
-  urb->hcpriv = NULL;
-}
-
-static int ep_priv_create(struct usb_host_endpoint *ep, int mem_flags) {
-  struct crisv10_ep_priv *ep_priv;
-  
-  ep_priv = kmalloc(sizeof *ep_priv, mem_flags);
-  if (!ep_priv)
-    return -ENOMEM;
-  memset(ep_priv, 0, sizeof *ep_priv);
-
-  ep->hcpriv = ep_priv;
-  return 0;
-}
-
-static void ep_priv_free(struct usb_host_endpoint *ep) {
-  struct crisv10_ep_priv *ep_priv = ep->hcpriv;
-  ASSERT(ep_priv);
-  kfree(ep_priv);
-  ep->hcpriv = NULL;
-}
-
-/*
- * usb_check_bandwidth():
- *
- * old_alloc is from host_controller->bandwidth_allocated in microseconds;
- * bustime is from calc_bus_time(), but converted to microseconds.
- *
- * returns <bustime in us> if successful,
- * or -ENOSPC if bandwidth request fails.
- *
- * FIXME:
- * This initial implementation does not use Endpoint.bInterval
- * in managing bandwidth allocation.
- * It probably needs to be expanded to use Endpoint.bInterval.
- * This can be done as a later enhancement (correction).
- *
- * This will also probably require some kind of
- * frame allocation tracking...meaning, for example,
- * that if multiple drivers request interrupts every 10 USB frames,
- * they don't all have to be allocated at
- * frame numbers N, N+10, N+20, etc.  Some of them could be at
- * N+11, N+21, N+31, etc., and others at
- * N+12, N+22, N+32, etc.
- *
- * Similarly for isochronous transfers...
- *
- * Individual HCDs can schedule more directly ... this logic
- * is not correct for high speed transfers.
- */
-static int crisv10_usb_check_bandwidth(
-  struct usb_device *dev,
-  struct urb *urb)
-{
-  unsigned int	pipe = urb->pipe;
-  long					bustime;
-  int						is_in = usb_pipein (pipe);
-  int						is_iso = usb_pipeisoc (pipe);
-  int						old_alloc = dev->bus->bandwidth_allocated;
-  int						new_alloc;
-
-  bustime = NS_TO_US (usb_calc_bus_time (dev->speed, is_in, is_iso,
-                                         usb_maxpacket (dev, pipe, !is_in)));
-  if (is_iso)
-    bustime /= urb->number_of_packets;
-
-  new_alloc = old_alloc + (int) bustime;
-  if (new_alloc > FRAME_TIME_MAX_USECS_ALLOC) {
-    dev_dbg (&dev->dev, "usb_check_bandwidth FAILED: %d + %ld = %d usec\n",
-             old_alloc, bustime, new_alloc);
-    bustime = -ENOSPC;      /* report error */
-  }
-
-  return bustime;
-}
-
-/**
- * usb_claim_bandwidth - records bandwidth for a periodic transfer
- * @dev: source/target of request
- * @urb: request (urb->dev == dev)
- * @bustime: bandwidth consumed, in (average) microseconds per frame
- * @isoc: true iff the request is isochronous
- *
- * HCDs are expected not to overcommit periodic bandwidth, and to record such
- * reservations whenever endpoints are added to the periodic schedule.
- *
- * FIXME averaging per-frame is suboptimal.  Better to sum over the HCD's
- * entire periodic schedule ... 32 frames for OHCI, 1024 for UHCI, settable
- * for EHCI (256/512/1024 frames, default 1024) and have the bus expose how
- * large its periodic schedule is.
- */
-static void crisv10_usb_claim_bandwidth(
-  struct usb_device *dev,
-  struct urb *urb, int bustime, int isoc)
-{
-  dev->bus->bandwidth_allocated += bustime;
-  if (isoc)
-    dev->bus->bandwidth_isoc_reqs++;
-  else
-    dev->bus->bandwidth_int_reqs++;
-  struct crisv10_urb_priv *urb_priv;
-  urb_priv = urb->hcpriv;
-  urb_priv->bandwidth = bustime;
-}
-
-/**
- * usb_release_bandwidth - reverses effect of usb_claim_bandwidth()
- * @hcd: host controller
- * @isoc: true iff the request is isochronous
- * @bandwidth: bandwidth returned
- *
- * This records that previously allocated bandwidth has been released.
- * Bandwidth is released when endpoints are removed from the host controller's
- * periodic schedule.
- */
-static void crisv10_usb_release_bandwidth(
-  struct usb_hcd *hcd,
-  int isoc,
-  int bandwidth)
-{
-  hcd_to_bus(hcd)->bandwidth_allocated -= bandwidth;
-  if (isoc)
-    hcd_to_bus(hcd)->bandwidth_isoc_reqs--;
-  else
-    hcd_to_bus(hcd)->bandwidth_int_reqs--;
-}
-
-
-/* EPID handling functions, managing EP-list in Etrax through wrappers */
-/* ------------------------------------------------------------------- */
-
-/* Sets up a new EPID for an endpoint or returns existing if found */
-static int tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb,
-			 int mem_flags) {
-  int epid;
-  char devnum, endpoint, out_traffic, slow;
-  int maxlen;
-  __u32 epid_data;
-  struct crisv10_ep_priv *ep_priv = ep->hcpriv;
-  
-  DBFENTER;
-  
-  /* Check if a valid epid already is setup for this endpoint */
-  if(ep_priv != NULL) {
-    return ep_priv->epid;
-  }
-
-  /* We must find and initiate a new epid for this urb. */
-  epid = tc_allocate_epid();
-  
-  if (epid == -1) {
-    /* Failed to allocate a new epid. */
-    DBFEXIT;
-    return epid;
-  }
-  
-  /* We now have a new epid to use. Claim it. */
-  epid_state[epid].inuse = 1;
-  
-  /* Init private data for new endpoint */
-  if(ep_priv_create(ep, mem_flags) != 0) {
-    return -ENOMEM;
-  }
-  ep_priv = ep->hcpriv;
-  ep_priv->epid = epid;
-
-  devnum = usb_pipedevice(urb->pipe);
-  endpoint = usb_pipeendpoint(urb->pipe);
-  slow = (urb->dev->speed == USB_SPEED_LOW);
-  maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe));
-
-  if (usb_pipetype(urb->pipe) == PIPE_CONTROL) {
-    /* We want both IN and OUT control traffic to be put on the same
-       EP/SB list. */
-    out_traffic = 1;
-  } else {
-    out_traffic = usb_pipeout(urb->pipe);
-  }
-    
-  if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
-    epid_data = IO_STATE(R_USB_EPT_DATA_ISO, valid, yes) |
-      /* FIXME: Change any to the actual port? */
-      IO_STATE(R_USB_EPT_DATA_ISO, port, any) |
-      IO_FIELD(R_USB_EPT_DATA_ISO, max_len, maxlen) |
-      IO_FIELD(R_USB_EPT_DATA_ISO, ep, endpoint) |
-      IO_FIELD(R_USB_EPT_DATA_ISO, dev, devnum);
-    etrax_epid_iso_set(epid, epid_data);
-  } else {
-    epid_data = IO_STATE(R_USB_EPT_DATA, valid, yes) |
-      IO_FIELD(R_USB_EPT_DATA, low_speed, slow) |
-      /* FIXME: Change any to the actual port? */
-      IO_STATE(R_USB_EPT_DATA, port, any) |
-      IO_FIELD(R_USB_EPT_DATA, max_len, maxlen) |
-      IO_FIELD(R_USB_EPT_DATA, ep, endpoint) |
-      IO_FIELD(R_USB_EPT_DATA, dev, devnum);
-    etrax_epid_set(epid, epid_data);
-  }
-  
-  epid_state[epid].out_traffic = out_traffic;
-  epid_state[epid].type = usb_pipetype(urb->pipe);
-
-  tc_warn("Setting up ep:0x%x epid:%d (addr:%d endp:%d max_len:%d %s %s %s)\n",
-	  (unsigned int)ep, epid, devnum, endpoint, maxlen,
-	  str_type(urb->pipe), out_traffic ? "out" : "in",
-	  slow ? "low" : "full");
-
-  /* Enable Isoc eof interrupt if we set up the first Isoc epid */
-  if(usb_pipeisoc(urb->pipe)) {
-    isoc_epid_counter++;
-    if(isoc_epid_counter == 1) {
-      isoc_warn("Enabled Isoc eof interrupt\n");
-      *R_USB_IRQ_MASK_SET = IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set);
-    }
-  }
-
-  DBFEXIT;
-  return epid;
-}
-
-static void tc_free_epid(struct usb_host_endpoint *ep) {
-  unsigned long flags;
-  struct crisv10_ep_priv *ep_priv = ep->hcpriv;
-  int epid;
-  volatile int timeout = 10000;
-
-  DBFENTER;
-
-  if (ep_priv == NULL) {
-    tc_warn("Trying to free unused epid on ep:0x%x\n", (unsigned int)ep);
-    DBFEXIT;
-    return;
-  }
-
-  epid = ep_priv->epid;
-
-  /* Disable Isoc eof interrupt if we free the last Isoc epid */
-  if(epid_isoc(epid)) {
-    ASSERT(isoc_epid_counter > 0);
-    isoc_epid_counter--;
-    if(isoc_epid_counter == 0) {
-      *R_USB_IRQ_MASK_CLR = IO_STATE(R_USB_IRQ_MASK_CLR, iso_eof, clr);
-      isoc_warn("Disabled Isoc eof interrupt\n");
-    }
-  }
-
-  /* Take lock manualy instead of in epid_x_x wrappers,
-     because we need to be polling here */
-  spin_lock_irqsave(&etrax_epid_lock, flags);
-  
-  *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid);
-  nop();
-  while((*R_USB_EPT_DATA & IO_MASK(R_USB_EPT_DATA, hold)) &&
-	(timeout-- > 0));
-  if(timeout == 0) {
-    warn("Timeout while waiting for epid:%d to drop hold\n", epid);
-  }
-  /* This will, among other things, set the valid field to 0. */
-  *R_USB_EPT_DATA = 0;
-  spin_unlock_irqrestore(&etrax_epid_lock, flags);
-  
-  /* Free resource in software state info list */
-  epid_state[epid].inuse = 0;
-
-  /* Free private endpoint data */
-  ep_priv_free(ep);
-  
-  DBFEXIT;
-}
-
-static int tc_allocate_epid(void) {
-  int i;
-  DBFENTER;
-  for (i = 0; i < NBR_OF_EPIDS; i++) {
-    if (!epid_inuse(i)) {
-      DBFEXIT;
-      return i;
-    }
-  }
-  
-  tc_warn("Found no free epids\n");
-  DBFEXIT;
-  return -1;
-}
-
-
-/* Wrappers around the list functions (include/linux/list.h). */
-/* ---------------------------------------------------------- */
-static inline int __urb_list_empty(int epid) {
-  int retval;
-  retval = list_empty(&urb_list[epid]);
-  return retval;
-}
-
-/* Returns first urb for this epid, or NULL if list is empty. */
-static inline struct urb *urb_list_first(int epid) {
-  unsigned long flags;
-  struct urb *first_urb = 0;
-  spin_lock_irqsave(&urb_list_lock, flags);
-  if (!__urb_list_empty(epid)) {
-    /* Get the first urb (i.e. head->next). */
-    urb_entry_t *urb_entry = list_entry((&urb_list[epid])->next, urb_entry_t, list);
-    first_urb = urb_entry->urb;
-  }
-  spin_unlock_irqrestore(&urb_list_lock, flags);
-  return first_urb;
-}
-
-/* Adds an urb_entry last in the list for this epid. */
-static inline void urb_list_add(struct urb *urb, int epid, int mem_flags) {
-  unsigned long flags;
-  urb_entry_t *urb_entry = (urb_entry_t *)kmalloc(sizeof(urb_entry_t), mem_flags);
-  ASSERT(urb_entry);
-  
-  urb_entry->urb = urb;
-  spin_lock_irqsave(&urb_list_lock, flags);
-  list_add_tail(&urb_entry->list, &urb_list[epid]);
-  spin_unlock_irqrestore(&urb_list_lock, flags);
-}
-
-/* Search through the list for an element that contains this urb. (The list
-   is expected to be short and the one we are about to delete will often be
-   the first in the list.)
-   Should be protected by spin_locks in calling function */
-static inline urb_entry_t *__urb_list_entry(struct urb *urb, int epid) {
-  struct list_head *entry;
-  struct list_head *tmp;
-  urb_entry_t *urb_entry;
-  
-  list_for_each_safe(entry, tmp, &urb_list[epid]) {
-    urb_entry = list_entry(entry, urb_entry_t, list);
-    ASSERT(urb_entry);
-    ASSERT(urb_entry->urb);
-    
-    if (urb_entry->urb == urb) {
-      return urb_entry;
-    }
-  }
-  return 0;
-}
-
-/* Same function as above but for global use. Protects list by spinlock */
-static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid) {
-  unsigned long flags;
-  urb_entry_t *urb_entry;
-  spin_lock_irqsave(&urb_list_lock, flags);
-  urb_entry = __urb_list_entry(urb, epid);
-  spin_unlock_irqrestore(&urb_list_lock, flags);
-  return (urb_entry);
-}
-
-/* Delete an urb from the list. */
-static inline void urb_list_del(struct urb *urb, int epid) {
-  unsigned long flags;
-  urb_entry_t *urb_entry;
-
-  /* Delete entry and free. */
-  spin_lock_irqsave(&urb_list_lock, flags);
-  urb_entry = __urb_list_entry(urb, epid);
-  ASSERT(urb_entry);
-
-  list_del(&urb_entry->list);
-  spin_unlock_irqrestore(&urb_list_lock, flags);
-  kfree(urb_entry);
-}
-
-/* Move an urb to the end of the list. */
-static inline void urb_list_move_last(struct urb *urb, int epid) {
-  unsigned long flags;
-  urb_entry_t *urb_entry;
-  
-  spin_lock_irqsave(&urb_list_lock, flags);
-  urb_entry = __urb_list_entry(urb, epid);
-  ASSERT(urb_entry);
-
-  list_del(&urb_entry->list);
-  list_add_tail(&urb_entry->list, &urb_list[epid]);
-  spin_unlock_irqrestore(&urb_list_lock, flags);
-}
-
-/* Get the next urb in the list. */
-static inline struct urb *urb_list_next(struct urb *urb, int epid) {
-  unsigned long flags;
-  urb_entry_t *urb_entry;
-
-  spin_lock_irqsave(&urb_list_lock, flags);
-  urb_entry = __urb_list_entry(urb, epid);
-  ASSERT(urb_entry);
-
-  if (urb_entry->list.next != &urb_list[epid]) {
-    struct list_head *elem = urb_entry->list.next;
-    urb_entry = list_entry(elem, urb_entry_t, list);
-    spin_unlock_irqrestore(&urb_list_lock, flags);
-    return urb_entry->urb;
-  } else {
-    spin_unlock_irqrestore(&urb_list_lock, flags);
-    return NULL;
-  }
-}
-
-struct USB_EP_Desc* create_ep(int epid, struct USB_SB_Desc* sb_desc,
-			      int mem_flags) {
-  struct USB_EP_Desc *ep_desc;
-  ep_desc = (struct USB_EP_Desc *) kmem_cache_alloc(usb_desc_cache, mem_flags);
-  if(ep_desc == NULL)
-    return NULL;
-  memset(ep_desc, 0, sizeof(struct USB_EP_Desc));
-
-  ep_desc->hw_len = 0;
-  ep_desc->command = (IO_FIELD(USB_EP_command, epid, epid) |
-		      IO_STATE(USB_EP_command, enable, yes));
-  if(sb_desc == NULL) {
-    ep_desc->sub = 0;
-  } else {
-    ep_desc->sub = virt_to_phys(sb_desc);
-  }
-  return ep_desc;
-}
-
-#define TT_ZOUT  0
-#define TT_IN    1
-#define TT_OUT   2
-#define TT_SETUP 3
-
-#define CMD_EOL  IO_STATE(USB_SB_command, eol, yes)
-#define CMD_INTR IO_STATE(USB_SB_command, intr, yes)
-#define CMD_FULL IO_STATE(USB_SB_command, full, yes)
-
-/* Allocation and setup of a generic SB. Used to create SETUP, OUT and ZOUT
-   SBs. Also used by create_sb_in() to avoid same allocation procedure at two
-   places */
-struct USB_SB_Desc* create_sb(struct USB_SB_Desc* sb_prev, int tt, void* data,
-			      int datalen, int mem_flags) {
-  struct USB_SB_Desc *sb_desc;
-  sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags);
-  if(sb_desc == NULL)
-    return NULL;
-  memset(sb_desc, 0, sizeof(struct USB_SB_Desc));
-
-  sb_desc->command = IO_FIELD(USB_SB_command, tt, tt) |
-                     IO_STATE(USB_SB_command, eot, yes);
-
-  sb_desc->sw_len = datalen;
-  if(data != NULL) {
-    sb_desc->buf = virt_to_phys(data);
-  } else {
-    sb_desc->buf = 0;
-  }
-  if(sb_prev != NULL) {
-    sb_prev->next = virt_to_phys(sb_desc);
-  }
-  return sb_desc;
-}
-
-/* Creates a copy of an existing SB by allocation space for it and copy
-   settings */
-struct USB_SB_Desc* create_sb_copy(struct USB_SB_Desc* sb_orig, int mem_flags) {
-  struct USB_SB_Desc *sb_desc;
-  sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags);
-  if(sb_desc == NULL)
-    return NULL;
-
-  memcpy(sb_desc, sb_orig, sizeof(struct USB_SB_Desc));
-  return sb_desc;
-}
-
-/* A specific create_sb function for creation of in SBs. This is due to
-   that datalen in In SBs shows how many packets we are expecting. It also
-   sets up the rem field to show if how many bytes we expect in last packet
-   if it's not a full one */
-struct USB_SB_Desc* create_sb_in(struct USB_SB_Desc* sb_prev, int datalen,
-				 int maxlen, int mem_flags) {
-  struct USB_SB_Desc *sb_desc;
-  sb_desc = create_sb(sb_prev, TT_IN, NULL,
-		      datalen ? (datalen - 1) / maxlen + 1 : 0, mem_flags);
-  if(sb_desc == NULL)
-    return NULL;
-  sb_desc->command |= IO_FIELD(USB_SB_command, rem, datalen % maxlen);
-  return sb_desc;
-}
-
-void set_sb_cmds(struct USB_SB_Desc *sb_desc, __u16 flags) {
-  sb_desc->command |= flags;
-}
-
-int create_sb_for_urb(struct urb *urb, int mem_flags) {
-  int is_out = !usb_pipein(urb->pipe);
-  int type = usb_pipetype(urb->pipe);
-  int maxlen = usb_maxpacket(urb->dev, urb->pipe, is_out);
-  int buf_len = urb->transfer_buffer_length;
-  void *buf = buf_len > 0 ? urb->transfer_buffer : NULL;
-  struct USB_SB_Desc *sb_desc = NULL;
-
-  struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-  ASSERT(urb_priv != NULL);
-
-  switch(type) {
-  case PIPE_CONTROL:
-    /* Setup stage */
-    sb_desc = create_sb(NULL, TT_SETUP, urb->setup_packet, 8, mem_flags);
-    if(sb_desc == NULL)
-      return -ENOMEM;
-    set_sb_cmds(sb_desc, CMD_FULL);
-
-    /* Attach first SB to URB */
-    urb_priv->first_sb = sb_desc;    
-
-    if (is_out) { /* Out Control URB */
-      /* If this Control OUT transfer has an optional data stage we add
-	 an OUT token before the mandatory IN (status) token */
-      if ((buf_len > 0) && buf) {
-	sb_desc = create_sb(sb_desc, TT_OUT, buf, buf_len, mem_flags);
-	if(sb_desc == NULL)
-	  return -ENOMEM;
-	set_sb_cmds(sb_desc, CMD_FULL);
-      }
-
-      /* Status stage */
-      /* The data length has to be exactly 1. This is due to a requirement
-         of the USB specification that a host must be prepared to receive
-         data in the status phase */
-      sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-    } else { /* In control URB */
-      /* Data stage */
-      sb_desc = create_sb_in(sb_desc, buf_len, maxlen, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-
-      /* Status stage */
-      /* Read comment at zout_buffer declaration for an explanation to this. */
-      sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-      /* Set descriptor interrupt flag for in URBs so we can finish URB after
-         zout-packet has been sent */
-      set_sb_cmds(sb_desc, CMD_INTR | CMD_FULL);
-    }
-    /* Set end-of-list flag in last SB */
-    set_sb_cmds(sb_desc, CMD_EOL);
-    /* Attach last SB to URB */
-    urb_priv->last_sb = sb_desc;
-    break;
-
-  case PIPE_BULK:
-    if (is_out) { /* Out Bulk URB */
-      sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-      /* The full field is set to yes, even if we don't actually check that
-	 this is a full-length transfer (i.e., that transfer_buffer_length %
-	 maxlen = 0).
-	 Setting full prevents the USB controller from sending an empty packet
-	 in that case.  However, if URB_ZERO_PACKET was set we want that. */
-      if (!(urb->transfer_flags & URB_ZERO_PACKET)) {
-	set_sb_cmds(sb_desc, CMD_FULL);
-      }
-    } else { /* In Bulk URB */
-      sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-    }
-    /* Set end-of-list flag for last SB */
-    set_sb_cmds(sb_desc, CMD_EOL);
-
-    /* Attach SB to URB */
-    urb_priv->first_sb = sb_desc;
-    urb_priv->last_sb = sb_desc;
-    break;
-
-  case PIPE_INTERRUPT:
-    if(is_out) { /* Out Intr URB */
-      sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-
-      /* The full field is set to yes, even if we don't actually check that
-	 this is a full-length transfer (i.e., that transfer_buffer_length %
-	 maxlen = 0).
-	 Setting full prevents the USB controller from sending an empty packet
-	 in that case.  However, if URB_ZERO_PACKET was set we want that. */
-      if (!(urb->transfer_flags & URB_ZERO_PACKET)) {
-	set_sb_cmds(sb_desc, CMD_FULL);
-      }
-      /* Only generate TX interrupt if it's a Out URB*/
-      set_sb_cmds(sb_desc, CMD_INTR);
-
-    } else { /* In Intr URB */
-      sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-    }
-    /* Set end-of-list flag for last SB */
-    set_sb_cmds(sb_desc, CMD_EOL);
-
-    /* Attach SB to URB */
-    urb_priv->first_sb = sb_desc;
-    urb_priv->last_sb = sb_desc;
-
-    break;
-  case PIPE_ISOCHRONOUS:
-    if(is_out) { /* Out Isoc URB */
-      int i;
-      if(urb->number_of_packets == 0) {
-	tc_err("Can't create SBs for Isoc URB with zero packets\n");
-	return -EPIPE;
-      }
-      /* Create one SB descriptor for each packet and link them together. */
-      for(i = 0; i < urb->number_of_packets; i++) {
-	if (urb->iso_frame_desc[i].length > 0) {
-
-	  sb_desc = create_sb(sb_desc, TT_OUT, urb->transfer_buffer +
-			      urb->iso_frame_desc[i].offset,
-			      urb->iso_frame_desc[i].length, mem_flags);
-	  if(sb_desc == NULL)
-	    return -ENOMEM;
-
-	  /* Check if it's a full length packet */
-	  if (urb->iso_frame_desc[i].length ==
-	      usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe))) {
-	    set_sb_cmds(sb_desc, CMD_FULL);
-	  }
-	  
-	} else { /* zero length packet */
-	  sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags);
-	  if(sb_desc == NULL)
-	    return -ENOMEM;
-	  set_sb_cmds(sb_desc, CMD_FULL);
-	}
-	/* Attach first SB descriptor to URB */
-	if (i == 0) {
-	  urb_priv->first_sb = sb_desc;
-	}
-      }
-      /* Set interrupt and end-of-list flags in last SB */
-      set_sb_cmds(sb_desc, CMD_INTR | CMD_EOL);
-      /* Attach last SB descriptor to URB */
-      urb_priv->last_sb = sb_desc;
-      tc_dbg("Created %d out SBs for Isoc URB:0x%x\n",
-	       urb->number_of_packets, (unsigned int)urb);
-    } else { /* In Isoc URB */
-      /* Actual number of packets is not relevant for periodic in traffic as
-	 long as it is more than zero.  Set to 1 always. */
-      sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags);
-      if(sb_desc == NULL)
-	return -ENOMEM;
-      /* Set end-of-list flags for SB */
-      set_sb_cmds(sb_desc, CMD_EOL);
-
-      /* Attach SB to URB */
-      urb_priv->first_sb = sb_desc;
-      urb_priv->last_sb = sb_desc;
-    }
-    break;
-  default:
-    tc_err("Unknown pipe-type\n");
-    return -EPIPE;
-    break;
-  }
-  return 0;
-}
-
-int init_intr_urb(struct urb *urb, int mem_flags) {
-  struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-  struct USB_EP_Desc* ep_desc;
-  int interval;
-  int i;
-  int ep_count;
-
-  ASSERT(urb_priv != NULL);
-  ASSERT(usb_pipeint(urb->pipe));
-  /* We can't support interval longer than amount of eof descriptors in
-     TxIntrEPList */
-  if(urb->interval > MAX_INTR_INTERVAL) {
-    tc_err("Interrupt interval %dms too big (max: %dms)\n", urb->interval,
-	   MAX_INTR_INTERVAL);
-    return -EINVAL;
-  }
-
-  /* We assume that the SB descriptors already have been setup */
-  ASSERT(urb_priv->first_sb != NULL);
-
-  /* Round of the interval to 2^n, it is obvious that this code favours
-     smaller numbers, but that is actually a good thing */
-  /* FIXME: The "rounding error" for larger intervals will be quite
-     large. For in traffic this shouldn't be a problem since it will only
-     mean that we "poll" more often. */
-  interval = urb->interval;
-  for (i = 0; interval; i++) {
-    interval = interval >> 1;
-  }
-  urb_priv->interval = 1 << (i - 1);
-
-  /* We can only have max interval for Out Interrupt due to that we can only
-     handle one linked in EP for a certain epid in the Intr descr array at the
-     time. The USB Controller in the Etrax 100LX continues to process Intr EPs
-     so we have no way of knowing which one that caused the actual transfer if
-     we have several linked in. */
-  if(usb_pipeout(urb->pipe)) {
-    urb_priv->interval = MAX_INTR_INTERVAL;
-  }
-
-  /* Calculate amount of EPs needed */
-  ep_count = MAX_INTR_INTERVAL / urb_priv->interval;
-
-  for(i = 0; i < ep_count; i++) {
-    ep_desc = create_ep(urb_priv->epid, urb_priv->first_sb, mem_flags);
-    if(ep_desc == NULL) {
-      /* Free any descriptors that we may have allocated before failure */
-      while(i > 0) {
-	i--;
-	kfree(urb_priv->intr_ep_pool[i]);
-      }
-      return -ENOMEM;
-    }
-    urb_priv->intr_ep_pool[i] = ep_desc;
-  }
-  urb_priv->intr_ep_pool_length = ep_count;
-  return 0;
-}
-
-/* DMA RX/TX functions */
-/* ----------------------- */
-
-static void tc_dma_init_rx_list(void) {
-  int i;
-
-  /* Setup descriptor list except last one */
-  for (i = 0; i < (NBR_OF_RX_DESC - 1); i++) {
-    RxDescList[i].sw_len = RX_DESC_BUF_SIZE;
-    RxDescList[i].command = 0;
-    RxDescList[i].next = virt_to_phys(&RxDescList[i + 1]);
-    RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE));
-    RxDescList[i].hw_len = 0;
-    RxDescList[i].status = 0;
-    
-    /* DMA IN cache bug. (struct etrax_dma_descr has the same layout as
-       USB_IN_Desc for the relevant fields.) */
-    prepare_rx_descriptor((struct etrax_dma_descr*)&RxDescList[i]);
-    
-  }
-  /* Special handling of last descriptor */
-  RxDescList[i].sw_len = RX_DESC_BUF_SIZE;
-  RxDescList[i].command = IO_STATE(USB_IN_command, eol, yes);
-  RxDescList[i].next = virt_to_phys(&RxDescList[0]);
-  RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE));
-  RxDescList[i].hw_len = 0;
-  RxDescList[i].status = 0;
-  
-  /* Setup list pointers that show progress in list */
-  myNextRxDesc = &RxDescList[0];
-  myLastRxDesc = &RxDescList[NBR_OF_RX_DESC - 1];
-  
-  flush_etrax_cache();
-  /* Point DMA to first descriptor in list and start it */
-  *R_DMA_CH9_FIRST = virt_to_phys(myNextRxDesc);
-  *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, start);
-}
-
-
-static void tc_dma_init_tx_bulk_list(void) {
-  int i;
-  volatile struct USB_EP_Desc *epDescr;
-
-  for (i = 0; i < (NBR_OF_EPIDS - 1); i++) {
-    epDescr = &(TxBulkEPList[i]);
-    CHECK_ALIGN(epDescr);
-    epDescr->hw_len = 0;
-    epDescr->command = IO_FIELD(USB_EP_command, epid, i);
-    epDescr->sub = 0;
-    epDescr->next = virt_to_phys(&TxBulkEPList[i + 1]);
-
-    /* Initiate two EPs, disabled and with the eol flag set. No need for any
-       preserved epid. */
-    
-    /* The first one has the intr flag set so we get an interrupt when the DMA
-       channel is about to become disabled. */
-    CHECK_ALIGN(&TxBulkDummyEPList[i][0]);
-    TxBulkDummyEPList[i][0].hw_len = 0;
-    TxBulkDummyEPList[i][0].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) |
-				       IO_STATE(USB_EP_command, eol, yes) |
-				       IO_STATE(USB_EP_command, intr, yes));
-    TxBulkDummyEPList[i][0].sub = 0;
-    TxBulkDummyEPList[i][0].next = virt_to_phys(&TxBulkDummyEPList[i][1]);
-    
-    /* The second one. */
-    CHECK_ALIGN(&TxBulkDummyEPList[i][1]);
-    TxBulkDummyEPList[i][1].hw_len = 0;
-    TxBulkDummyEPList[i][1].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) |
-				       IO_STATE(USB_EP_command, eol, yes));
-    TxBulkDummyEPList[i][1].sub = 0;
-    /* The last dummy's next pointer is the same as the current EP's next pointer. */
-    TxBulkDummyEPList[i][1].next = virt_to_phys(&TxBulkEPList[i + 1]);
-  }
-
-  /* Special handling of last descr in list, make list circular */
-  epDescr = &TxBulkEPList[i];
-  CHECK_ALIGN(epDescr);
-  epDescr->hw_len = 0;
-  epDescr->command = IO_STATE(USB_EP_command, eol, yes) |
-    IO_FIELD(USB_EP_command, epid, i);
-  epDescr->sub = 0;
-  epDescr->next = virt_to_phys(&TxBulkEPList[0]);
-  
-  /* Init DMA sub-channel pointers to last item in each list */
-  *R_DMA_CH8_SUB0_EP = virt_to_phys(&TxBulkEPList[i]);
-  /* No point in starting the bulk channel yet.
-   *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */
-}
-
-static void tc_dma_init_tx_ctrl_list(void) {
-  int i;
-  volatile struct USB_EP_Desc *epDescr;
-
-  for (i = 0; i < (NBR_OF_EPIDS - 1); i++) {
-    epDescr = &(TxCtrlEPList[i]);
-    CHECK_ALIGN(epDescr);
-    epDescr->hw_len = 0;
-    epDescr->command = IO_FIELD(USB_EP_command, epid, i);
-    epDescr->sub = 0;
-    epDescr->next = virt_to_phys(&TxCtrlEPList[i + 1]);
-  }
-  /* Special handling of last descr in list, make list circular */
-  epDescr = &TxCtrlEPList[i];
-  CHECK_ALIGN(epDescr);
-  epDescr->hw_len = 0;
-  epDescr->command = IO_STATE(USB_EP_command, eol, yes) |
-    IO_FIELD(USB_EP_command, epid, i);
-  epDescr->sub = 0;
-  epDescr->next = virt_to_phys(&TxCtrlEPList[0]);
-  
-  /* Init DMA sub-channel pointers to last item in each list */
-  *R_DMA_CH8_SUB1_EP = virt_to_phys(&TxCtrlEPList[i]);
-  /* No point in starting the ctrl channel yet.
-   *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */
-}
-
-
-static void tc_dma_init_tx_intr_list(void) {
-  int i;
-
-  TxIntrSB_zout.sw_len = 1;
-  TxIntrSB_zout.next = 0;
-  TxIntrSB_zout.buf = virt_to_phys(&zout_buffer[0]);
-  TxIntrSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) |
-			   IO_STATE(USB_SB_command, tt, zout) |
-			   IO_STATE(USB_SB_command, full, yes) |
-			   IO_STATE(USB_SB_command, eot, yes) |
-			   IO_STATE(USB_SB_command, eol, yes));
-  
-  for (i = 0; i < (MAX_INTR_INTERVAL - 1); i++) {
-    CHECK_ALIGN(&TxIntrEPList[i]);
-    TxIntrEPList[i].hw_len = 0;
-    TxIntrEPList[i].command =
-      (IO_STATE(USB_EP_command, eof, yes) |
-       IO_STATE(USB_EP_command, enable, yes) |
-       IO_FIELD(USB_EP_command, epid, INVALID_EPID));
-    TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout);
-    TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[i + 1]);
-  }
-
-  /* Special handling of last descr in list, make list circular */
-  CHECK_ALIGN(&TxIntrEPList[i]);
-  TxIntrEPList[i].hw_len = 0;
-  TxIntrEPList[i].command =
-    (IO_STATE(USB_EP_command, eof, yes) |
-     IO_STATE(USB_EP_command, eol, yes) |
-     IO_STATE(USB_EP_command, enable, yes) |
-     IO_FIELD(USB_EP_command, epid, INVALID_EPID));
-  TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout);
-  TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[0]);
-
-  intr_dbg("Initiated Intr EP descriptor list\n");
-
-
-  /* Connect DMA 8 sub-channel 2 to first in list */
-  *R_DMA_CH8_SUB2_EP = virt_to_phys(&TxIntrEPList[0]);
-}
-
-static void tc_dma_init_tx_isoc_list(void) {
-  int i;
-
-  DBFENTER;
-
-  /* Read comment at zout_buffer declaration for an explanation to this. */
-  TxIsocSB_zout.sw_len = 1;
-  TxIsocSB_zout.next = 0;
-  TxIsocSB_zout.buf = virt_to_phys(&zout_buffer[0]);
-  TxIsocSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) |
-			   IO_STATE(USB_SB_command, tt, zout) |
-			   IO_STATE(USB_SB_command, full, yes) |
-			   IO_STATE(USB_SB_command, eot, yes) |
-			   IO_STATE(USB_SB_command, eol, yes));
-
-  /* The last isochronous EP descriptor is a dummy. */
-  for (i = 0; i < (NBR_OF_EPIDS - 1); i++) {
-    CHECK_ALIGN(&TxIsocEPList[i]);
-    TxIsocEPList[i].hw_len = 0;
-    TxIsocEPList[i].command = IO_FIELD(USB_EP_command, epid, i);
-    TxIsocEPList[i].sub = 0;
-    TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[i + 1]);
-  }
-
-  CHECK_ALIGN(&TxIsocEPList[i]);
-  TxIsocEPList[i].hw_len = 0;
-
-  /* Must enable the last EP descr to get eof interrupt. */
-  TxIsocEPList[i].command = (IO_STATE(USB_EP_command, enable, yes) |
-			     IO_STATE(USB_EP_command, eof, yes) |
-			     IO_STATE(USB_EP_command, eol, yes) |
-			     IO_FIELD(USB_EP_command, epid, INVALID_EPID));
-  TxIsocEPList[i].sub = virt_to_phys(&TxIsocSB_zout);
-  TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[0]);
-
-  *R_DMA_CH8_SUB3_EP = virt_to_phys(&TxIsocEPList[0]);
-  *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start);
-}
-
-static int tc_dma_init(struct usb_hcd *hcd) {
-  tc_dma_init_rx_list();
-  tc_dma_init_tx_bulk_list();
-  tc_dma_init_tx_ctrl_list();
-  tc_dma_init_tx_intr_list();
-  tc_dma_init_tx_isoc_list();
-
-  if (cris_request_dma(USB_TX_DMA_NBR,
-		       "ETRAX 100LX built-in USB (Tx)",
-		       DMA_VERBOSE_ON_ERROR,
-		       dma_usb)) {
-    err("Could not allocate DMA ch 8 for USB");
-    return -EBUSY;
-  }
- 	
-  if (cris_request_dma(USB_RX_DMA_NBR,
-		       "ETRAX 100LX built-in USB (Rx)",
-		       DMA_VERBOSE_ON_ERROR,
-		       dma_usb)) {
-    err("Could not allocate DMA ch 9 for USB");
-    return -EBUSY;
-  }
-
-  *R_IRQ_MASK2_SET =
-    /* Note that these interrupts are not used. */
-    IO_STATE(R_IRQ_MASK2_SET, dma8_sub0_descr, set) |
-    /* Sub channel 1 (ctrl) descr. interrupts are used. */
-    IO_STATE(R_IRQ_MASK2_SET, dma8_sub1_descr, set) |
-    IO_STATE(R_IRQ_MASK2_SET, dma8_sub2_descr, set) |
-    /* Sub channel 3 (isoc) descr. interrupts are used. */
-    IO_STATE(R_IRQ_MASK2_SET, dma8_sub3_descr, set);
-  
-  /* Note that the dma9_descr interrupt is not used. */
-  *R_IRQ_MASK2_SET =
-    IO_STATE(R_IRQ_MASK2_SET, dma9_eop, set) |
-    IO_STATE(R_IRQ_MASK2_SET, dma9_descr, set);
-
-  if (request_irq(ETRAX_USB_RX_IRQ, tc_dma_rx_interrupt, 0,
-		  "ETRAX 100LX built-in USB (Rx)", hcd)) {
-    err("Could not allocate IRQ %d for USB", ETRAX_USB_RX_IRQ);
-    return -EBUSY;
-  }
-  
-  if (request_irq(ETRAX_USB_TX_IRQ, tc_dma_tx_interrupt, 0,
-		  "ETRAX 100LX built-in USB (Tx)", hcd)) {
-    err("Could not allocate IRQ %d for USB", ETRAX_USB_TX_IRQ);
-    return -EBUSY;
-  }
-
-  return 0;
-}
-
-static void tc_dma_destroy(void) {
-  free_irq(ETRAX_USB_RX_IRQ, NULL);
-  free_irq(ETRAX_USB_TX_IRQ, NULL);
-
-  cris_free_dma(USB_TX_DMA_NBR, "ETRAX 100LX built-in USB (Tx)");
-  cris_free_dma(USB_RX_DMA_NBR, "ETRAX 100LX built-in USB (Rx)");
-
-}
-
-static void tc_dma_link_intr_urb(struct urb *urb);
-
-/* Handle processing of Bulk, Ctrl and Intr queues */
-static void tc_dma_process_queue(int epid) {
-  struct urb *urb;
-  struct crisv10_urb_priv *urb_priv;
-  unsigned long flags;
-  char toggle;
-
-  if(epid_state[epid].disabled) {
-    /* Don't process any URBs on a disabled endpoint */
-    return;
-  }
-
-  /* Do not disturb us while fiddling with EPs and epids */
-  local_irq_save(flags);
-
-  /* For bulk, Ctrl and Intr can we only have one URB active at a time for
-     a specific EP. */
-  if(activeUrbList[epid] != NULL) {
-    /* An URB is already active on EP, skip checking queue */
-    local_irq_restore(flags);
-    return;
-  }
-
-  urb = urb_list_first(epid);
-  if(urb == NULL) {
-    /* No URB waiting in EP queue. Nothing do to */
-    local_irq_restore(flags);
-    return;
-  }
-
-  urb_priv = urb->hcpriv;
-  ASSERT(urb_priv != NULL);
-  ASSERT(urb_priv->urb_state == NOT_STARTED);
-  ASSERT(!usb_pipeisoc(urb->pipe));
-
-  /* Remove this URB from the queue and move it to active */
-  activeUrbList[epid] = urb;
-  urb_list_del(urb, epid);
-
-  urb_priv->urb_state = STARTED;
-
-  /* Reset error counters (regardless of which direction this traffic is). */
-  etrax_epid_clear_error(epid);
-
-  /* Special handling of Intr EP lists */
-  if(usb_pipeint(urb->pipe)) {
-    tc_dma_link_intr_urb(urb);
-    local_irq_restore(flags);
-    return;
-  }
-
-  /* Software must preset the toggle bits for Bulk and Ctrl */
-  if(usb_pipecontrol(urb->pipe)) {
-    /* Toggle bits are initialized only during setup transaction in a
-       CTRL transfer */
-    etrax_epid_set_toggle(epid, 0, 0);
-    etrax_epid_set_toggle(epid, 1, 0);
-  } else {
-    toggle = usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe),
-			   usb_pipeout(urb->pipe));
-    etrax_epid_set_toggle(epid, usb_pipeout(urb->pipe), toggle);
-  }
-
-  tc_dbg("Added SBs from (URB:0x%x %s %s) to epid %d: %s\n",
-	 (unsigned int)urb, str_dir(urb->pipe), str_type(urb->pipe), epid,
-	 sblist_to_str(urb_priv->first_sb));
-
-  /* We start the DMA sub channel without checking if it's running or not,
-     because:
-     1) If it's already running, issuing the start command is a nop.
-     2) We avoid a test-and-set race condition. */
-  switch(usb_pipetype(urb->pipe)) {
-  case PIPE_BULK:
-    /* Assert that the EP descriptor is disabled. */
-    ASSERT(!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)));
-
-    /* Set up and enable the EP descriptor. */
-    TxBulkEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
-    TxBulkEPList[epid].hw_len = 0;
-    TxBulkEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
-
-    /* Check if the dummy list is already with us (if several urbs were queued). */
-    if (usb_pipein(urb->pipe) && (TxBulkEPList[epid].next != virt_to_phys(&TxBulkDummyEPList[epid][0]))) {
-      tc_dbg("Inviting dummy list to the party for urb 0x%lx, epid %d", 
-	     (unsigned long)urb, epid);
-      
-      /* We don't need to check if the DMA is at this EP or not before changing the
-	 next pointer, since we will do it in one 32-bit write (EP descriptors are
-	 32-bit aligned). */
-      TxBulkEPList[epid].next = virt_to_phys(&TxBulkDummyEPList[epid][0]);
-    }
-
-    restart_dma8_sub0();
-
-    /* Update/restart the bulk start timer since we just started the channel.*/
-    mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL);
-    /* Update/restart the bulk eot timer since we just inserted traffic. */
-    mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL);
-    break;
-  case PIPE_CONTROL:
-    /* Assert that the EP descriptor is disabled. */
-    ASSERT(!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)));
-
-    /* Set up and enable the EP descriptor. */
-    TxCtrlEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
-    TxCtrlEPList[epid].hw_len = 0;
-    TxCtrlEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
-
-    *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB1_CMD, cmd, start);
-    break;
-  }
-  local_irq_restore(flags);
-}
-
-static void tc_dma_link_intr_urb(struct urb *urb) {
-  struct crisv10_urb_priv *urb_priv = urb->hcpriv;
-  volatile struct USB_EP_Desc *tmp_ep;
-  struct USB_EP_Desc *ep_desc;
-  int i = 0, epid;
-  int pool_idx = 0;
-
-  ASSERT(urb_priv != NULL);
-  epid = urb_priv->epid;
-  ASSERT(urb_priv->interval > 0);
-  ASSERT(urb_priv->intr_ep_pool_length > 0);
-
-  tmp_ep = &TxIntrEPList[0];
-
-  /* Only insert one EP descriptor in list for Out Intr URBs.
-     We can only handle Out Intr with interval of 128ms because
-     it's not possible to insert several Out Intr EPs because they
-     are not consumed by the DMA. */
-  if(usb_pipeout(urb->pipe)) {
-    ep_desc = urb_priv->intr_ep_pool[0];
-    ASSERT(ep_desc);
-    ep_desc->next = tmp_ep->next;
-    tmp_ep->next = virt_to_phys(ep_desc);
-    i++;
-  } else {
-    /* Loop through Intr EP descriptor list and insert EP for URB at
-       specified interval */
-    do {
-      /* Each EP descriptor with eof flag sat signals a new frame */
-      if (tmp_ep->command & IO_MASK(USB_EP_command, eof)) {
-	/* Insert a EP from URBs EP pool at correct interval */
-	if ((i % urb_priv->interval) == 0) {
-	  ep_desc = urb_priv->intr_ep_pool[pool_idx];
-	  ASSERT(ep_desc);
-	  ep_desc->next = tmp_ep->next;
-	  tmp_ep->next = virt_to_phys(ep_desc);
-	  pool_idx++;
-	  ASSERT(pool_idx <= urb_priv->intr_ep_pool_length);
-	}
-	i++;
-      }
-      tmp_ep = (struct USB_EP_Desc *)phys_to_virt(tmp_ep->next);
-    } while(tmp_ep != &TxIntrEPList[0]);
-  }
-
-  intr_dbg("Added SBs to intr epid %d: %s interval:%d (%d EP)\n", epid,
-	   sblist_to_str(urb_priv->first_sb), urb_priv->interval, pool_idx);
-
-  /* We start the DMA sub channel without checking if it's running or not,
-     because:
-     1) If it's already running, issuing the start command is a nop.
-     2) We avoid a test-and-set race condition. */
-  *R_DMA_CH8_SUB2_CMD = IO_STATE(R_DMA_CH8_SUB2_CMD, cmd, start);
-}
-
-static void tc_dma_process_isoc_urb(struct urb *urb) {
-  unsigned long flags;
-  struct crisv10_urb_priv *urb_priv = urb->hcpriv;
-  int epid;
-
-  /* Do not disturb us while fiddling with EPs and epids */
-  local_irq_save(flags);
-
-  ASSERT(urb_priv);
-  ASSERT(urb_priv->first_sb);
-  epid = urb_priv->epid;
-
-  if(activeUrbList[epid] == NULL) {
-    /* EP is idle, so make this URB active */
-    activeUrbList[epid] = urb;
-    urb_list_del(urb, epid);
-    ASSERT(TxIsocEPList[epid].sub == 0);
-    ASSERT(!(TxIsocEPList[epid].command &
-	     IO_STATE(USB_EP_command, enable, yes)));
-
-    /* Differentiate between In and Out Isoc. Because In SBs are not consumed*/
-    if(usb_pipein(urb->pipe)) {
-    /* Each EP for In Isoc will have only one SB descriptor, setup when
-       submitting the first active urb. We do it here by copying from URBs
-       pre-allocated SB. */
-      memcpy((void *)&(TxIsocSBList[epid]), urb_priv->first_sb,
-	     sizeof(TxIsocSBList[epid]));
-      TxIsocEPList[epid].hw_len = 0;
-      TxIsocEPList[epid].sub = virt_to_phys(&(TxIsocSBList[epid]));
-    } else {
-      /* For Out Isoc we attach the pre-allocated list of SBs for the URB */
-      TxIsocEPList[epid].hw_len = 0;
-      TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
-
-      isoc_dbg("Attached first URB:0x%x[%d] to epid:%d first_sb:0x%x"
-	       " last_sb::0x%x\n",
-	       (unsigned int)urb, urb_priv->urb_num, epid,
-	       (unsigned int)(urb_priv->first_sb),
-	       (unsigned int)(urb_priv->last_sb));
-    }
-
-    if (urb->transfer_flags & URB_ISO_ASAP) {
-      /* The isoc transfer should be started as soon as possible. The
-	 start_frame field is a return value if URB_ISO_ASAP was set. Comparing
-	 R_USB_FM_NUMBER with a USB Chief trace shows that the first isoc IN
-	 token is sent 2 frames later. I'm not sure how this affects usage of
-	 the start_frame field by the device driver, or how it affects things
-	 when USB_ISO_ASAP is not set, so therefore there's no compensation for
-	 the 2 frame "lag" here. */
-      urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff);
-      TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
-      urb_priv->urb_state = STARTED;
-      isoc_dbg("URB_ISO_ASAP set, urb->start_frame set to %d\n",
-	       urb->start_frame);
-    } else {
-      /* Not started yet. */
-      urb_priv->urb_state = NOT_STARTED;
-      isoc_warn("urb_priv->urb_state set to NOT_STARTED for URB:0x%x\n",
-		(unsigned int)urb);
-    }
-
-  } else {
-    /* An URB is already active on the EP. Leave URB in queue and let
-       finish_isoc_urb process it after current active URB */
-    ASSERT(TxIsocEPList[epid].sub != 0);
-
-    if(usb_pipein(urb->pipe)) {
-      /* Because there already is a active In URB on this epid we do nothing
-         and the finish_isoc_urb() function will handle switching to next URB*/
-
-    } else { /* For Out Isoc, insert new URBs traffic last in SB-list. */
-      struct USB_SB_Desc *temp_sb_desc;
-
-      /* Set state STARTED to all Out Isoc URBs added to SB list because we
-         don't know how many of them that are finished before descr interrupt*/
-      urb_priv->urb_state = STARTED;
-
-      /* Find end of current SB list by looking for SB with eol flag sat */
-      temp_sb_desc = phys_to_virt(TxIsocEPList[epid].sub);
-      while ((temp_sb_desc->command & IO_MASK(USB_SB_command, eol)) !=
-	     IO_STATE(USB_SB_command, eol, yes)) {
-	ASSERT(temp_sb_desc->next);
-	temp_sb_desc = phys_to_virt(temp_sb_desc->next);
-      }
-
-      isoc_dbg("Appended URB:0x%x[%d] (first:0x%x last:0x%x) to epid:%d"
-	       " sub:0x%x eol:0x%x\n",
-	       (unsigned int)urb, urb_priv->urb_num,
-	       (unsigned int)(urb_priv->first_sb),
-	       (unsigned int)(urb_priv->last_sb), epid,
-	       (unsigned int)phys_to_virt(TxIsocEPList[epid].sub),
-	       (unsigned int)temp_sb_desc);
-
-      /* Next pointer must be set before eol is removed. */
-      temp_sb_desc->next = virt_to_phys(urb_priv->first_sb);
-      /* Clear the previous end of list flag since there is a new in the
-	 added SB descriptor list. */
-      temp_sb_desc->command &= ~IO_MASK(USB_SB_command, eol);
-
-      if (!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) {
-	__u32 epid_data;
-	/* 8.8.5 in Designer's Reference says we should check for and correct
-	   any errors in the EP here.  That should not be necessary if
-	   epid_attn is handled correctly, so we assume all is ok. */
-	epid_data = etrax_epid_iso_get(epid);
-	if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) !=
-	    IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
-	  isoc_err("Disabled Isoc EP with error:%d on epid:%d when appending"
-		   " URB:0x%x[%d]\n",
-		   IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data), epid,
-		   (unsigned int)urb, urb_priv->urb_num);
-	}
-
-	/* The SB list was exhausted. */
-	if (virt_to_phys(urb_priv->last_sb) != TxIsocEPList[epid].sub) {
-	  /* The new sublist did not get processed before the EP was
-	     disabled.  Setup the EP again. */
-
-	  if(virt_to_phys(temp_sb_desc) == TxIsocEPList[epid].sub) {
-	    isoc_dbg("EP for epid:%d stoped at SB:0x%x before newly inserted"
-		     ", restarting from this URBs SB:0x%x\n",
-		     epid, (unsigned int)temp_sb_desc,
-		     (unsigned int)(urb_priv->first_sb));
-	    TxIsocEPList[epid].hw_len = 0;
-	    TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
-	    urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff);
-	    /* Enable the EP again so data gets processed this time */
-	    TxIsocEPList[epid].command |=
-	      IO_STATE(USB_EP_command, enable, yes);
-
-	  } else {
-	    /* The EP has been disabled but not at end this URB (god knows
-	       where). This should generate an epid_attn so we should not be
-	       here */
-	    isoc_warn("EP was disabled on sb:0x%x before SB list for"
-		     " URB:0x%x[%d] got processed\n",
-		     (unsigned int)phys_to_virt(TxIsocEPList[epid].sub),
-		     (unsigned int)urb, urb_priv->urb_num);
-	  }
-	} else {
-	  /* This might happend if we are slow on this function and isn't
-	     an error. */
-	  isoc_dbg("EP was disabled and finished with SBs from appended"
-		   " URB:0x%x[%d]\n", (unsigned int)urb, urb_priv->urb_num);
-	}
-      }
-    }
-  }
-  
-  /* Start the DMA sub channel */
-  *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start);
-
-  local_irq_restore(flags);
-}
-
-static void tc_dma_unlink_intr_urb(struct urb *urb) {
-  struct crisv10_urb_priv *urb_priv = urb->hcpriv;
-  volatile struct USB_EP_Desc *first_ep;  /* First EP in the list. */
-  volatile struct USB_EP_Desc *curr_ep;   /* Current EP, the iterator. */
-  volatile struct USB_EP_Desc *next_ep;   /* The EP after current. */
-  volatile struct USB_EP_Desc *unlink_ep; /* The one we should remove from
-					     the list. */
-  int count = 0;
-  volatile int timeout = 10000;
-  int epid;
-
-  /* Read 8.8.4 in Designer's Reference, "Removing an EP Descriptor from the
-     List". */
-  ASSERT(urb_priv);
-  ASSERT(urb_priv->intr_ep_pool_length > 0);
-  epid = urb_priv->epid;
-
-  /* First disable all Intr EPs belonging to epid for this URB */
-  first_ep = &TxIntrEPList[0];
-  curr_ep = first_ep;
-  do {
-    next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
-    if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) {
-      /* Disable EP */
-      next_ep->command &= ~IO_MASK(USB_EP_command, enable);
-    }
-    curr_ep = phys_to_virt(curr_ep->next);
-  } while (curr_ep != first_ep);
-
-
-  /* Now unlink all EPs belonging to this epid from Descr list */
-  first_ep = &TxIntrEPList[0];
-  curr_ep = first_ep;
-  do {
-    next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
-    if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) {
-      /* This is the one we should unlink. */
-      unlink_ep = next_ep;
-
-      /* Actually unlink the EP from the DMA list. */
-      curr_ep->next = unlink_ep->next;
-
-      /* Wait until the DMA is no longer at this descriptor. */
-      while((*R_DMA_CH8_SUB2_EP == virt_to_phys(unlink_ep)) &&
-	    (timeout-- > 0));
-      if(timeout == 0) {
-	warn("Timeout while waiting for DMA-TX-Intr to leave unlink EP\n");
-      }
-      
-      count++;
-    }
-    curr_ep = phys_to_virt(curr_ep->next);
-  } while (curr_ep != first_ep);
-
-  if(count != urb_priv->intr_ep_pool_length) {
-    intr_warn("Unlinked %d of %d Intr EPs for URB:0x%x[%d]\n", count,
-	      urb_priv->intr_ep_pool_length, (unsigned int)urb,
-	      urb_priv->urb_num);
-  } else {
-    intr_dbg("Unlinked %d of %d interrupt EPs for URB:0x%x\n", count,
-	     urb_priv->intr_ep_pool_length, (unsigned int)urb);
-  }
-}
-
-static void check_finished_bulk_tx_epids(struct usb_hcd *hcd,
-						    int timer) {
-  unsigned long flags;
-  int epid;
-  struct urb *urb;
-  struct crisv10_urb_priv * urb_priv;
-  __u32 epid_data;
-
-  /* Protect TxEPList */
-  local_irq_save(flags);
-
-  for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
-    /* A finished EP descriptor is disabled and has a valid sub pointer */
-    if (!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) &&
-	(TxBulkEPList[epid].sub != 0)) {
-
-      /* Get the active URB for this epid */
-      urb = activeUrbList[epid];
-      /* Sanity checks */
-      ASSERT(urb);
-      urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-      ASSERT(urb_priv);
-      
-      /* Only handle finished out Bulk EPs here,
-	 and let RX interrupt take care of the rest */
-      if(!epid_out_traffic(epid)) {
-	continue;
-      }
-
-      if(timer) {
-	tc_warn("Found finished %s Bulk epid:%d URB:0x%x[%d] from timeout\n",
-		epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb,
-		urb_priv->urb_num);
-      } else {
-	tc_dbg("Found finished %s Bulk epid:%d URB:0x%x[%d] from interrupt\n",
-	       epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb,
-	       urb_priv->urb_num);
-      }
-
-      if(urb_priv->urb_state == UNLINK) {
-	/* This Bulk URB is requested to be unlinked, that means that the EP
-	   has been disabled and we might not have sent all data */
-	tc_finish_urb(hcd, urb, urb->status);
-	continue;
-      }
-
-      ASSERT(urb_priv->urb_state == STARTED);
-      if (phys_to_virt(TxBulkEPList[epid].sub) != urb_priv->last_sb) {
-	tc_err("Endpoint got disabled before reaching last sb\n");
-      }
-	
-      epid_data = etrax_epid_get(epid);
-      if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) ==
-	  IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
-	/* This means that the endpoint has no error, is disabled
-	   and had inserted traffic, i.e. transfer successfully completed. */
-	tc_finish_urb(hcd, urb, 0);
-      } else {
-	/* Shouldn't happen. We expect errors to be caught by epid
-	   attention. */
-	tc_err("Found disabled bulk EP desc (epid:%d error:%d)\n",
-	       epid, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data));
-      }
-    } else {
-      tc_dbg("Ignoring In Bulk epid:%d, let RX interrupt handle it\n", epid);
-    }
-  }
-
-  local_irq_restore(flags);
-}
-
-static void check_finished_ctrl_tx_epids(struct usb_hcd *hcd) {
-  unsigned long flags;
-  int epid;
-  struct urb *urb;
-  struct crisv10_urb_priv * urb_priv;
-  __u32 epid_data;
-
-  /* Protect TxEPList */
-  local_irq_save(flags);
-
-  for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
-    if(epid == DUMMY_EPID)
-      continue;
-
-    /* A finished EP descriptor is disabled and has a valid sub pointer */
-    if (!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) &&
-	(TxCtrlEPList[epid].sub != 0)) {
-      
-      /* Get the active URB for this epid */
-      urb = activeUrbList[epid];
-
-      if(urb == NULL) {
-	tc_warn("Found finished Ctrl epid:%d with no active URB\n", epid);
-	continue;
-      }
-      
-      /* Sanity checks */
-      ASSERT(usb_pipein(urb->pipe));
-      urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-      ASSERT(urb_priv);
-      if (phys_to_virt(TxCtrlEPList[epid].sub) != urb_priv->last_sb) {
-	tc_err("Endpoint got disabled before reaching last sb\n");
-      }
-
-      epid_data = etrax_epid_get(epid);
-      if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) ==
-	  IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
-	/* This means that the endpoint has no error, is disabled
-	   and had inserted traffic, i.e. transfer successfully completed. */
-
-	/* Check if RX-interrupt for In Ctrl has been processed before
-	   finishing the URB */
-	if(urb_priv->ctrl_rx_done) {
-	  tc_dbg("Finishing In Ctrl URB:0x%x[%d] in tx_interrupt\n",
-		 (unsigned int)urb, urb_priv->urb_num);
-	  tc_finish_urb(hcd, urb, 0);
-	} else {
-	  /* If we get zout descriptor interrupt before RX was done for a
-	     In Ctrl transfer, then we flag that and it will be finished
-	     in the RX-Interrupt */
-	  urb_priv->ctrl_zout_done = 1;
-	  tc_dbg("Got zout descr interrupt before RX interrupt\n");
-	}
-      } else {
-	/* Shouldn't happen. We expect errors to be caught by epid
-	   attention. */
-	tc_err("Found disabled Ctrl EP desc (epid:%d URB:0x%x[%d]) error_code:%d\n", epid, (unsigned int)urb, urb_priv->urb_num, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data));
-	__dump_ep_desc(&(TxCtrlEPList[epid]));
-	__dump_ept_data(epid);
-      }      
-    }
-  }
-  local_irq_restore(flags);
-}
-
-/* This function goes through all epids that are setup for Out Isoc transfers
-   and marks (isoc_out_done) all queued URBs that the DMA has finished
-   transfer for.
-   No URB completetion is done here to make interrupt routine return quickly.
-   URBs are completed later with help of complete_isoc_bottom_half() that
-   becomes schedules when this functions is finished. */
-static void check_finished_isoc_tx_epids(void) {
-  unsigned long flags;
-  int epid;
-  struct urb *urb;
-  struct crisv10_urb_priv * urb_priv;
-  struct USB_SB_Desc* sb_desc;
-  int epid_done;
-
-  /* Protect TxIsocEPList */
-  local_irq_save(flags);
-
-  for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
-    if (TxIsocEPList[epid].sub == 0 || epid == INVALID_EPID ||
-	!epid_out_traffic(epid)) {
-      /* Nothing here to see. */
-      continue;
-    }
-    ASSERT(epid_inuse(epid));
-    ASSERT(epid_isoc(epid));
-
-    sb_desc = phys_to_virt(TxIsocEPList[epid].sub);
-    /* Find the last descriptor of the currently active URB for this ep.
-       This is the first descriptor in the sub list marked for a descriptor
-       interrupt. */
-    while (sb_desc && !IO_EXTRACT(USB_SB_command, intr, sb_desc->command)) {
-      sb_desc = sb_desc->next ? phys_to_virt(sb_desc->next) : 0;
-    }
-    ASSERT(sb_desc);
-
-    isoc_dbg("Descr IRQ checking epid:%d sub:0x%x intr:0x%x\n",
-	     epid, (unsigned int)phys_to_virt(TxIsocEPList[epid].sub),
-	     (unsigned int)sb_desc);
-
-    urb = activeUrbList[epid];
-    if(urb == NULL) {
-      isoc_err("Isoc Descr irq on epid:%d with no active URB\n", epid);
-      continue;
-    }
-
-    epid_done = 0;
-    while(urb && !epid_done) {
-      /* Sanity check. */
-      ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS);
-      ASSERT(usb_pipeout(urb->pipe));
-      
-      urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-      ASSERT(urb_priv);
-      ASSERT(urb_priv->urb_state == STARTED ||
-	     urb_priv->urb_state == UNLINK);
-      
-      if (sb_desc != urb_priv->last_sb) {
-	/* This urb has been sent. */
-	urb_priv->isoc_out_done = 1;
-
-      } else { /* Found URB that has last_sb as the interrupt reason */
-
-	/* Check if EP has been disabled, meaning that all transfers are done*/
-	if(!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) {
-	  ASSERT((sb_desc->command & IO_MASK(USB_SB_command, eol)) ==
-		 IO_STATE(USB_SB_command, eol, yes));
-	  ASSERT(sb_desc->next == 0);
-	  urb_priv->isoc_out_done = 1;
-	} else {
-	  isoc_dbg("Skipping URB:0x%x[%d] because EP not disabled yet\n",
-		   (unsigned int)urb, urb_priv->urb_num);
-	}
-	/* Stop looking any further in queue */
-	epid_done = 1;	
-      }
-
-      if (!epid_done) {
-	if(urb == activeUrbList[epid]) {
-	  urb = urb_list_first(epid);
-	} else {
-	  urb = urb_list_next(urb, epid);
-	}
-      }
-    } /* END: while(urb && !epid_done) */
-  }
-
-  local_irq_restore(flags);
-}
-
-
-/* This is where the Out Isoc URBs are realy completed. This function is
-   scheduled from tc_dma_tx_interrupt() when one or more Out Isoc transfers
-   are done. This functions completes all URBs earlier marked with
-   isoc_out_done by fast interrupt routine check_finished_isoc_tx_epids() */
-
-static void complete_isoc_bottom_half(struct work_struct* work) {
-  struct crisv10_isoc_complete_data *comp_data;
-  struct usb_iso_packet_descriptor *packet;
-  struct crisv10_urb_priv * urb_priv;
-  unsigned long flags;
-  struct urb* urb;
-  int epid_done;
-  int epid;
-  int i;
-
-  comp_data = container_of(work, struct crisv10_isoc_complete_data, usb_bh);
-
-  local_irq_save(flags);
-
-  for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) {
-    if(!epid_inuse(epid) || !epid_isoc(epid) || !epid_out_traffic(epid) || epid == DUMMY_EPID) {
-      /* Only check valid Out Isoc epids */
-      continue;
-    }
-
-    isoc_dbg("Isoc bottom-half checking epid:%d, sub:0x%x\n", epid,
-	     (unsigned int)phys_to_virt(TxIsocEPList[epid].sub));
-
-    /* The descriptor interrupt handler has marked all transmitted Out Isoc
-       URBs with isoc_out_done.  Now we traverse all epids and for all that
-       have out Isoc traffic we traverse its URB list and complete the
-       transmitted URBs. */
-    epid_done = 0;
-    while (!epid_done) {
-
-      /* Get the active urb (if any) */
-      urb = activeUrbList[epid];
-      if (urb == 0) {
-	isoc_dbg("No active URB on epid:%d anymore\n", epid);
-	epid_done = 1;
-	continue;
-      }
-
-      /* Sanity check. */
-      ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS);
-      ASSERT(usb_pipeout(urb->pipe));
-
-      urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-      ASSERT(urb_priv);
-
-      if (!(urb_priv->isoc_out_done)) {
-	/* We have reached URB that isn't flaged done yet, stop traversing. */
-	isoc_dbg("Stoped traversing Out Isoc URBs on epid:%d"
-		 " before not yet flaged URB:0x%x[%d]\n",
-		 epid, (unsigned int)urb, urb_priv->urb_num);
-	epid_done = 1;
-	continue;
-      }
-
-      /* This urb has been sent. */
-      isoc_dbg("Found URB:0x%x[%d] that is flaged isoc_out_done\n",
-	       (unsigned int)urb, urb_priv->urb_num);
-
-      /* Set ok on transfered packets for this URB and finish it */
-      for (i = 0; i < urb->number_of_packets; i++) {
-	packet = &urb->iso_frame_desc[i];
-	packet->status = 0;
-	packet->actual_length = packet->length;
-      }
-      urb_priv->isoc_packet_counter = urb->number_of_packets;
-      tc_finish_urb(comp_data->hcd, urb, 0);
-
-    } /* END: while(!epid_done) */
-  } /* END: for(epid...) */
-
-  local_irq_restore(flags);
-  kmem_cache_free(isoc_compl_cache, comp_data);
-}
-
-
-static void check_finished_intr_tx_epids(struct usb_hcd *hcd) {
-  unsigned long flags;
-  int epid;
-  struct urb *urb;
-  struct crisv10_urb_priv * urb_priv;
-  volatile struct USB_EP_Desc *curr_ep;   /* Current EP, the iterator. */
-  volatile struct USB_EP_Desc *next_ep;   /* The EP after current. */
-
-  /* Protect TxintrEPList */
-  local_irq_save(flags);
-
-  for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
-    if(!epid_inuse(epid) || !epid_intr(epid) || !epid_out_traffic(epid)) {
-      /* Nothing to see on this epid. Only check valid Out Intr epids */
-      continue;
-    }
-
-    urb = activeUrbList[epid];
-    if(urb == 0) {
-      intr_warn("Found Out Intr epid:%d with no active URB\n", epid);
-      continue;
-    }
-
-    /* Sanity check. */
-    ASSERT(usb_pipetype(urb->pipe) == PIPE_INTERRUPT);
-    ASSERT(usb_pipeout(urb->pipe));
-    
-    urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-    ASSERT(urb_priv);
-
-    /* Go through EPs between first and second sof-EP. It's here Out Intr EPs
-       are inserted.*/
-    curr_ep = &TxIntrEPList[0];
-    do {
-      next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
-      if(next_ep == urb_priv->intr_ep_pool[0]) {
-	/* We found the Out Intr EP for this epid */
-	
-	/* Disable it so it doesn't get processed again */
-	next_ep->command &= ~IO_MASK(USB_EP_command, enable);
-
-	/* Finish the active Out Intr URB with status OK */
-	tc_finish_urb(hcd, urb, 0);
-      }
-      curr_ep = phys_to_virt(curr_ep->next);
-    } while (curr_ep != &TxIntrEPList[1]);
-
-  }
-  local_irq_restore(flags);
-}
-
-/* Interrupt handler for DMA8/IRQ24 with subchannels (called from hardware intr) */
-static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc) {
-  struct usb_hcd *hcd = (struct usb_hcd*)vhc;
-  ASSERT(hcd);
-
-  if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub0_descr)) {
-    /* Clear this interrupt */
-    *R_DMA_CH8_SUB0_CLR_INTR = IO_STATE(R_DMA_CH8_SUB0_CLR_INTR, clr_descr, do);
-    restart_dma8_sub0();
-  }
-
-  if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub1_descr)) {
-    /* Clear this interrupt */
-    *R_DMA_CH8_SUB1_CLR_INTR = IO_STATE(R_DMA_CH8_SUB1_CLR_INTR, clr_descr, do);
-    check_finished_ctrl_tx_epids(hcd);
-  }
-
-  if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub2_descr)) {
-    /* Clear this interrupt */
-    *R_DMA_CH8_SUB2_CLR_INTR = IO_STATE(R_DMA_CH8_SUB2_CLR_INTR, clr_descr, do);
-    check_finished_intr_tx_epids(hcd);
-  }
-
-  if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub3_descr)) {
-    struct crisv10_isoc_complete_data* comp_data;
-
-    /* Flag done Out Isoc for later completion */
-    check_finished_isoc_tx_epids();
-
-    /* Clear this interrupt */
-    *R_DMA_CH8_SUB3_CLR_INTR = IO_STATE(R_DMA_CH8_SUB3_CLR_INTR, clr_descr, do);
-    /* Schedule bottom half of Out Isoc completion function. This function
-       finishes the URBs marked with isoc_out_done */
-    comp_data = (struct crisv10_isoc_complete_data*)
-      kmem_cache_alloc(isoc_compl_cache, GFP_ATOMIC);
-    ASSERT(comp_data != NULL);
-    comp_data ->hcd = hcd;
-
-    INIT_WORK(&comp_data->usb_bh, complete_isoc_bottom_half);
-    schedule_work(&comp_data->usb_bh);
-  }
-
-  return IRQ_HANDLED;
-}
-
-/* Interrupt handler for DMA9/IRQ25 (called from hardware intr) */
-static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc) {
-  unsigned long flags;
-  struct urb *urb;
-  struct usb_hcd *hcd = (struct usb_hcd*)vhc;
-  struct crisv10_urb_priv *urb_priv;
-  int epid = 0;
-  int real_error;
-
-  ASSERT(hcd);
-
-  /* Clear this interrupt. */
-  *R_DMA_CH9_CLR_INTR = IO_STATE(R_DMA_CH9_CLR_INTR, clr_eop, do);
-
-  /* Custom clear interrupt for this interrupt */
-  /* The reason we cli here is that we call the driver's callback functions. */
-  local_irq_save(flags);
-
-  /* Note that this while loop assumes that all packets span only
-     one rx descriptor. */
-  while(myNextRxDesc->status & IO_MASK(USB_IN_status, eop)) {
-    epid = IO_EXTRACT(USB_IN_status, epid, myNextRxDesc->status);
-    /* Get the active URB for this epid */
-    urb = activeUrbList[epid];
-
-    ASSERT(epid_inuse(epid));
-    if (!urb) {
-      dma_err("No urb for epid %d in rx interrupt\n", epid);
-      goto skip_out;
-    }
-
-    /* Check if any errors on epid */
-    real_error = 0;
-    if (myNextRxDesc->status & IO_MASK(USB_IN_status, error)) {
-      __u32 r_usb_ept_data;
-
-      if (usb_pipeisoc(urb->pipe)) {
-	r_usb_ept_data = etrax_epid_iso_get(epid);
-	if((r_usb_ept_data & IO_MASK(R_USB_EPT_DATA_ISO, valid)) &&
-	   (IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, r_usb_ept_data) == 0) &&
-	   (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata))) {
-	  /* Not an error, just a failure to receive an expected iso
-	     in packet in this frame.  This is not documented
-	     in the designers reference. Continue processing.
-	  */
-	} else real_error = 1;
-      } else real_error = 1;
-    }
-
-    if(real_error) {
-      dma_err("Error in RX descr on epid:%d for URB 0x%x",
-	      epid, (unsigned int)urb);
-      dump_ept_data(epid);
-      dump_in_desc(myNextRxDesc);
-      goto skip_out;
-    }
-
-    urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
-    ASSERT(urb_priv);
-    ASSERT(urb_priv->urb_state == STARTED ||
-	   urb_priv->urb_state == UNLINK);
-
-    if ((usb_pipetype(urb->pipe) == PIPE_BULK) ||
-	(usb_pipetype(urb->pipe) == PIPE_CONTROL) ||
-	(usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) {
-
-      /* We get nodata for empty data transactions, and the rx descriptor's
-	 hw_len field is not valid in that case. No data to copy in other
-	 words. */
-      if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) {
-	/* No data to copy */
-      } else {
-	/*
-	dma_dbg("Processing RX for URB:0x%x epid:%d (data:%d ofs:%d)\n",
-		(unsigned int)urb, epid, myNextRxDesc->hw_len,
-		urb_priv->rx_offset);
-	*/
-	/* Only copy data if URB isn't flaged to be unlinked*/
-	if(urb_priv->urb_state != UNLINK) {
-	  /* Make sure the data fits in the buffer. */
-	  if(urb_priv->rx_offset + myNextRxDesc->hw_len
-	     <= urb->transfer_buffer_length) {
-
-	    /* Copy the data to URBs buffer */
-	    memcpy(urb->transfer_buffer + urb_priv->rx_offset,
-		   phys_to_virt(myNextRxDesc->buf), myNextRxDesc->hw_len);
-	    urb_priv->rx_offset += myNextRxDesc->hw_len;
-	  } else {
-	    /* Signal overflow when returning URB */
-	    urb->status = -EOVERFLOW;
-	    tc_finish_urb_later(hcd, urb, urb->status);
-	  }
-	}
-      }
-
-      /* Check if it was the last packet in the transfer */
-      if (myNextRxDesc->status & IO_MASK(USB_IN_status, eot)) {
-	/* Special handling for In Ctrl URBs. */
-	if(usb_pipecontrol(urb->pipe) && usb_pipein(urb->pipe) &&
-	   !(urb_priv->ctrl_zout_done)) {
-	  /* Flag that RX part of Ctrl transfer is done. Because zout descr
-	     interrupt hasn't happend yet will the URB be finished in the
-	     TX-Interrupt. */
-	  urb_priv->ctrl_rx_done = 1;
-	  tc_dbg("Not finishing In Ctrl URB:0x%x from rx_interrupt, waiting"
-		 " for zout\n", (unsigned int)urb);
-	} else {
-	  tc_finish_urb(hcd, urb, 0);
-	}
-      }
-    } else { /* ISOC RX */
-      /*
-      isoc_dbg("Processing RX for epid:%d (URB:0x%x) ISOC pipe\n",
-	       epid, (unsigned int)urb);
-      */
-
-      struct usb_iso_packet_descriptor *packet;
-
-      if (urb_priv->urb_state == UNLINK) {
-	isoc_warn("Ignoring Isoc Rx data for urb being unlinked.\n");
-	goto skip_out;
-      } else if (urb_priv->urb_state == NOT_STARTED) {
-	isoc_err("What? Got Rx data for Isoc urb that isn't started?\n");
-	goto skip_out;
-      }
-
-      packet = &urb->iso_frame_desc[urb_priv->isoc_packet_counter];
-      ASSERT(packet);
-      packet->status = 0;
-
-      if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) {
-	/* We get nodata for empty data transactions, and the rx descriptor's
-	   hw_len field is not valid in that case. We copy 0 bytes however to
-	   stay in synch. */
-	packet->actual_length = 0;
-      } else {
-	packet->actual_length = myNextRxDesc->hw_len;
-	/* Make sure the data fits in the buffer. */
-	ASSERT(packet->actual_length <= packet->length);
-	memcpy(urb->transfer_buffer + packet->offset,
-	       phys_to_virt(myNextRxDesc->buf), packet->actual_length);
-	if(packet->actual_length > 0)
-	  isoc_dbg("Copied %d bytes, packet %d for URB:0x%x[%d]\n",
-		   packet->actual_length, urb_priv->isoc_packet_counter,
-		   (unsigned int)urb, urb_priv->urb_num);
-      }
-
-      /* Increment the packet counter. */
-      urb_priv->isoc_packet_counter++;
-
-      /* Note that we don't care about the eot field in the rx descriptor's
-	 status. It will always be set for isoc traffic. */
-      if (urb->number_of_packets == urb_priv->isoc_packet_counter) {
-	/* Complete the urb with status OK. */
-	tc_finish_urb(hcd, urb, 0);
-      }
-    }
-
-  skip_out:
-    myNextRxDesc->status = 0;
-    myNextRxDesc->command |= IO_MASK(USB_IN_command, eol);
-    myLastRxDesc->command &= ~IO_MASK(USB_IN_command, eol);
-    myLastRxDesc = myNextRxDesc;
-    myNextRxDesc = phys_to_virt(myNextRxDesc->next);
-    flush_etrax_cache();
-    *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, restart);
-  }
-
-  local_irq_restore(flags);
-
-  return IRQ_HANDLED;
-}
-
-static void tc_bulk_start_timer_func(unsigned long dummy) {
-  /* We might enable an EP descriptor behind the current DMA position when
-     it's about to decide that there are no more bulk traffic and it should
-     stop the bulk channel.
-     Therefore we periodically check if the bulk channel is stopped and there
-     is an enabled bulk EP descriptor, in which case we start the bulk
-     channel. */
-  
-  if (!(*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd))) {
-    int epid;
-
-    timer_dbg("bulk_start_timer: Bulk DMA channel not running.\n");
-
-    for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
-      if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
-	timer_warn("Found enabled EP for epid %d, starting bulk channel.\n",
-		   epid);
-	restart_dma8_sub0();
-
-	/* Restart the bulk eot timer since we just started the bulk channel.*/
-	mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL);
-
-	/* No need to search any further. */
-	break;
-      }
-    }
-  } else {
-    timer_dbg("bulk_start_timer: Bulk DMA channel running.\n");
-  }
-}
-
-static void tc_bulk_eot_timer_func(unsigned long dummy) {
-  struct usb_hcd *hcd = (struct usb_hcd*)dummy;
-  ASSERT(hcd);
-  /* Because of a race condition in the top half, we might miss a bulk eot.
-     This timer "simulates" a bulk eot if we don't get one for a while,
-     hopefully correcting the situation. */
-  timer_dbg("bulk_eot_timer timed out.\n");
-  check_finished_bulk_tx_epids(hcd, 1);
-}
-
-
-/*************************************************************/
-/*************************************************************/
-/* Device driver block                                       */
-/*************************************************************/
-/*************************************************************/
-
-/* Forward declarations for device driver functions */
-static int devdrv_hcd_probe(struct device *);
-static int devdrv_hcd_remove(struct device *);
-#ifdef CONFIG_PM
-static int devdrv_hcd_suspend(struct device *, u32, u32);
-static int devdrv_hcd_resume(struct device *, u32);
-#endif /* CONFIG_PM */
-
-/* the device */
-static struct platform_device *devdrv_hc_platform_device;
-
-/* device driver interface */
-static struct device_driver devdrv_hc_device_driver = {
-  .name =			(char *) hc_name,
-  .bus =			&platform_bus_type,
-
-  .probe =		devdrv_hcd_probe,
-  .remove =		devdrv_hcd_remove,
-
-#ifdef CONFIG_PM
-  .suspend =		devdrv_hcd_suspend,
-  .resume =		devdrv_hcd_resume,
-#endif /* CONFIG_PM */
-};
-
-/* initialize the host controller and driver  */
-static int __init_or_module devdrv_hcd_probe(struct device *dev)
-{
-  struct usb_hcd *hcd;
-  struct crisv10_hcd *crisv10_hcd;
-  int retval;
-
-  /* Check DMA burst length */
-  if(IO_EXTRACT(R_BUS_CONFIG, dma_burst, *R_BUS_CONFIG) !=
-     IO_STATE(R_BUS_CONFIG, dma_burst, burst32)) {
-    devdrv_err("Invalid DMA burst length in Etrax 100LX,"
-	       " needs to be 32\n");
-    return -EPERM;
-  }
-
-  hcd = usb_create_hcd(&crisv10_hc_driver, dev, dev->bus_id);
-  if (!hcd)
-    return -ENOMEM;
-
-  crisv10_hcd = hcd_to_crisv10_hcd(hcd);
-  spin_lock_init(&crisv10_hcd->lock);
-  crisv10_hcd->num_ports = num_ports();
-  crisv10_hcd->running = 0;
-
-  dev_set_drvdata(dev, crisv10_hcd);
-
-  devdrv_dbg("ETRAX USB IRQs HC:%d  RX:%d  TX:%d\n", ETRAX_USB_HC_IRQ,
-	  ETRAX_USB_RX_IRQ, ETRAX_USB_TX_IRQ);
-
-  /* Print out chip version read from registers */
-  int rev_maj = *R_USB_REVISION & IO_MASK(R_USB_REVISION, major);
-  int rev_min = *R_USB_REVISION & IO_MASK(R_USB_REVISION, minor);
-  if(rev_min == 0) {
-    devdrv_info("Etrax 100LX USB Revision %d v1,2\n", rev_maj);
-  } else {
-    devdrv_info("Etrax 100LX USB Revision %d v%d\n", rev_maj, rev_min);
-  }
-
-  devdrv_info("Bulk timer interval, start:%d eot:%d\n",
-	      BULK_START_TIMER_INTERVAL,
-	      BULK_EOT_TIMER_INTERVAL);
-
-
-  /* Init root hub data structures */
-  if(rh_init()) {
-    devdrv_err("Failed init data for Root Hub\n");
-    retval = -ENOMEM;
-  }
-
-  if(port_in_use(0)) {
-    if (cris_request_io_interface(if_usb_1, "ETRAX100LX USB-HCD")) {
-      printk(KERN_CRIT "usb-host: request IO interface usb1 failed");
-      retval = -EBUSY;
-      goto out;
-    }
-    devdrv_info("Claimed interface for USB physical port 1\n");
-  }
-  if(port_in_use(1)) {
-    if (cris_request_io_interface(if_usb_2, "ETRAX100LX USB-HCD")) {
-      /* Free first interface if second failed to be claimed */
-      if(port_in_use(0)) {
-	cris_free_io_interface(if_usb_1);
-      }
-      printk(KERN_CRIT "usb-host: request IO interface usb2 failed");
-      retval = -EBUSY;
-      goto out;
-    }
-    devdrv_info("Claimed interface for USB physical port 2\n");
-  }
-  
-  /* Init transfer controller structs and locks */
-  if((retval = tc_init(hcd)) != 0) {
-    goto out;
-  }
-
-  /* Attach interrupt functions for DMA and init DMA controller */
-  if((retval = tc_dma_init(hcd)) != 0) {
-    goto out;
-  }
-
-  /* Attach the top IRQ handler for USB controller interrupts */
-  if (request_irq(ETRAX_USB_HC_IRQ, crisv10_hcd_top_irq, 0,
-		  "ETRAX 100LX built-in USB (HC)", hcd)) {
-    err("Could not allocate IRQ %d for USB", ETRAX_USB_HC_IRQ);
-    retval = -EBUSY;
-    goto out;
-  }
-
-  /* iso_eof is only enabled when isoc traffic is running. */
-  *R_USB_IRQ_MASK_SET =
-    /* IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set) | */
-    IO_STATE(R_USB_IRQ_MASK_SET, bulk_eot, set) |
-    IO_STATE(R_USB_IRQ_MASK_SET, epid_attn, set) |
-    IO_STATE(R_USB_IRQ_MASK_SET, port_status, set) |
-    IO_STATE(R_USB_IRQ_MASK_SET, ctl_status, set);
-
-
-  crisv10_ready_wait();
-  /* Reset the USB interface. */
-  *R_USB_COMMAND =
-    IO_STATE(R_USB_COMMAND, port_sel, nop) |
-    IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-    IO_STATE(R_USB_COMMAND, ctrl_cmd, reset);
-
-  /* Designer's Reference, p. 8 - 10 says we should Initate R_USB_FM_PSTART to
-     0x2A30 (10800), to guarantee that control traffic gets 10% of the
-     bandwidth, and periodic transfer may allocate the rest (90%).
-     This doesn't work though.
-     The value 11960 is chosen to be just after the SOF token, with a couple
-     of bit times extra for possible bit stuffing. */
-  *R_USB_FM_PSTART = IO_FIELD(R_USB_FM_PSTART, value, 11960);
-
-  crisv10_ready_wait();
-  /* Configure the USB interface as a host controller. */
-  *R_USB_COMMAND =
-    IO_STATE(R_USB_COMMAND, port_sel, nop) |
-    IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-    IO_STATE(R_USB_COMMAND, ctrl_cmd, host_config);
-
-
-  /* Check so controller not busy before enabling ports */
-  crisv10_ready_wait();
-
-  /* Enable selected USB ports */
-  if(port_in_use(0)) {
-    *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no);
-  } else {
-    *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, yes);
-  }
-  if(port_in_use(1)) {
-    *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no);
-  } else {
-    *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, yes);
-  }
-
-  crisv10_ready_wait();
-  /* Start processing of USB traffic. */
-  *R_USB_COMMAND =
-    IO_STATE(R_USB_COMMAND, port_sel, nop) |
-    IO_STATE(R_USB_COMMAND, port_cmd, reset) |
-    IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
-
-  /* Do not continue probing initialization before USB interface is done */
-  crisv10_ready_wait();
-
-  /* Register our Host Controller to USB Core
-   * Finish the remaining parts of generic HCD initialization: allocate the
-   * buffers of consistent memory, register the bus
-   * and call the driver's reset() and start() routines. */
-  retval = usb_add_hcd(hcd, ETRAX_USB_HC_IRQ, IRQF_DISABLED);
-  if (retval != 0) {
-    devdrv_err("Failed registering HCD driver\n");
-    goto out;
-  }
-
-  return 0;
-
- out:
-  devdrv_hcd_remove(dev);
-  return retval;
-}
-
-
-/* cleanup after the host controller and driver */
-static int __init_or_module devdrv_hcd_remove(struct device *dev)
-{
-  struct crisv10_hcd *crisv10_hcd = dev_get_drvdata(dev);
-  struct usb_hcd *hcd;
-
-  if (!crisv10_hcd)
-    return 0;
-  hcd = crisv10_hcd_to_hcd(crisv10_hcd);
-
-
-  /* Stop USB Controller in Etrax 100LX */
-  crisv10_hcd_reset(hcd);
-
-  usb_remove_hcd(hcd);
-  devdrv_dbg("Removed HCD from USB Core\n");
-
-  /* Free USB Controller IRQ */
-  free_irq(ETRAX_USB_HC_IRQ, NULL);
-
-  /* Free resources */
-  tc_dma_destroy();
-  tc_destroy();
-
-
-  if(port_in_use(0)) {
-    cris_free_io_interface(if_usb_1);
-  }
-  if(port_in_use(1)) {
-    cris_free_io_interface(if_usb_2);
-  }
-
-  devdrv_dbg("Freed all claimed resources\n");
-
-  return 0;
-}
-
-
-#ifdef	CONFIG_PM
-
-static int devdrv_hcd_suspend(struct usb_hcd *hcd, u32 state, u32 level)
-{
-  return 0; /* no-op for now */
-}
-
-static int devdrv_hcd_resume(struct usb_hcd *hcd, u32 level)
-{
-  return 0; /* no-op for now */
-}
-
-#endif /* CONFIG_PM */
-
-
-/*************************************************************/
-/*************************************************************/
-/* Module block                                              */
-/*************************************************************/
-/*************************************************************/
- 
-/* register driver */
-static int __init module_hcd_init(void) 
-{
-  
-  if (usb_disabled())
-    return -ENODEV;
-
-  /* Here we select enabled ports by following defines created from
-     menuconfig */
-#ifndef CONFIG_ETRAX_USB_HOST_PORT1
-  ports &= ~(1<<0);
-#endif
-#ifndef CONFIG_ETRAX_USB_HOST_PORT2
-  ports &= ~(1<<1);
-#endif
-
-  printk(KERN_INFO "%s version "VERSION" "COPYRIGHT"\n", product_desc);
-
-  devdrv_hc_platform_device =
-    platform_device_register_simple((char *) hc_name, 0, NULL, 0);
-
-  if (IS_ERR(devdrv_hc_platform_device))
-    return PTR_ERR(devdrv_hc_platform_device);
-  return driver_register(&devdrv_hc_device_driver);
-  /* 
-   * Note that we do not set the DMA mask for the device,
-   * i.e. we pretend that we will use PIO, since no specific
-   * allocation routines are needed for DMA buffers. This will
-   * cause the HCD buffer allocation routines to fall back to
-   * kmalloc().
-   */
-}
-
-/* unregister driver */
-static void __exit module_hcd_exit(void) 
-{	
-  driver_unregister(&devdrv_hc_device_driver);
-}
-
-
-/* Module hooks */
-module_init(module_hcd_init);
-module_exit(module_hcd_exit);
diff --git a/target/linux/etrax/files/drivers/usb/host/hc-crisv10.h b/target/linux/etrax/files/drivers/usb/host/hc-crisv10.h
deleted file mode 100644
index 58a0b62..0000000
--- a/target/linux/etrax/files/drivers/usb/host/hc-crisv10.h
+++ /dev/null
@@ -1,333 +0,0 @@
-#ifndef __LINUX_ETRAX_USB_H
-#define __LINUX_ETRAX_USB_H
-
-#include <linux/types.h>
-#include <linux/list.h>
-
-struct USB_IN_Desc {
-  volatile __u16 sw_len;
-  volatile __u16 command;
-  volatile unsigned long next;
-  volatile unsigned long buf;
-  volatile __u16 hw_len;
-  volatile __u16 status;
-};
-
-struct USB_SB_Desc {
-  volatile __u16 sw_len;
-  volatile __u16 command;
-  volatile unsigned long next;
-  volatile unsigned long buf;
-};
-
-struct USB_EP_Desc {
-  volatile __u16 hw_len;
-  volatile __u16 command;
-  volatile unsigned long sub;
-  volatile unsigned long next;
-};
-
-
-/* Root Hub port status struct */
-struct crisv10_rh {
-  volatile __u16 wPortChange[2];
-  volatile __u16 wPortStatusPrev[2];
-};
-
-/* HCD description */
-struct crisv10_hcd {
-  spinlock_t		lock;
-  __u8			num_ports;
-  __u8                  running;
-};
-
-
-/* Endpoint HC private data description */
-struct crisv10_ep_priv {
-  int epid;
-};
-
-/* Additional software state info for a USB Controller epid */
-struct etrax_epid {
-  __u8 inuse;       /* !0 = setup in Etrax and used for a endpoint */
-  __u8 disabled;    /* !0 = Temporarly disabled to avoid resubmission */
-  __u8 type;        /* Setup as: PIPE_BULK, PIPE_CONTROL ... */
-  __u8 out_traffic; /* !0 = This epid is for out traffic */
-};
-
-/* Struct to hold information of scheduled later URB completion */
-struct urb_later_data {
-  struct delayed_work dws;
-  struct usb_hcd *hcd;
-  struct urb *urb;
-  int urb_num;
-  int status;
-};
-
-
-typedef enum {
-  STARTED,
-  NOT_STARTED,
-  UNLINK,
-} crisv10_urb_state_t;
-
-
-struct crisv10_urb_priv {
-  /* Sequence number for this URB. Every new submited URB gets this from
-     a incrementing counter. Used when a URB is scheduled for later finish to
-     be sure that the intended URB hasn't already been completed (device
-     drivers has a tendency to reuse URBs once they are completed, causing us
-     to not be able to single old ones out only based on the URB pointer.) */
-  __u32 urb_num;
-
-  /* The first_sb field is used for freeing all SB descriptors belonging
-     to an urb. The corresponding ep descriptor's sub pointer cannot be
-     used for this since the DMA advances the sub pointer as it processes
-     the sb list. */
-  struct USB_SB_Desc *first_sb;
-
-  /* The last_sb field referes to the last SB descriptor that belongs to
-     this urb. This is important to know so we can free the SB descriptors
-     that ranges between first_sb and last_sb. */
-  struct USB_SB_Desc *last_sb;
-  
-  /* The rx_offset field is used in ctrl and bulk traffic to keep track
-     of the offset in the urb's transfer_buffer where incoming data should be
-     copied to. */
-  __u32 rx_offset;
-  
-  /* Counter used in isochronous transfers to keep track of the
-     number of packets received/transmitted.  */
-  __u32 isoc_packet_counter;
-
-  /* Flag that marks if this Isoc Out URB has finished it's transfer. Used
-     because several URBs can be finished before list is processed */
-  __u8  isoc_out_done;
-  
-  /* This field is used to pass information about the urb's current state
-     between the various interrupt handlers (thus marked volatile). */
-  volatile crisv10_urb_state_t urb_state;
-  
-  /* In Ctrl transfers consist of (at least) 3 packets: SETUP, IN and ZOUT.
-     When DMA8 sub-channel 2 has processed the SB list for this sequence we
-     get a interrupt. We also get a interrupt for In transfers and which
-     one of these interrupts that comes first depends of data size and device.
-     To be sure that we have got both interrupts before we complete the URB
-     we have these to flags that shows which part that has completed.
-     We can then check when we get one of the interrupts that if the other has
-     occured it's safe for us to complete the URB, otherwise we set appropriate
-     flag and do the completion when we get the other interrupt. */
-  volatile unsigned char ctrl_zout_done;
-  volatile unsigned char ctrl_rx_done;
-
-  /* Connection between the submitted urb and ETRAX epid number */
-  __u8 epid;
-  
-  /* The rx_data_list field is used for periodic traffic, to hold
-     received data for later processing in the the complete_urb functions,
-     where the data us copied to the urb's transfer_buffer. Basically, we
-     use this intermediate storage because we don't know when it's safe to
-     reuse the transfer_buffer (FIXME?). */
-  struct list_head rx_data_list;
-
-
-  /* The interval time rounded up to closest 2^N */
-  int interval;
-
-  /* Pool of EP descriptors needed if it's a INTR transfer.
-     Amount of EPs in pool correspons to how many INTR that should
-     be inserted in TxIntrEPList (max 128, defined by MAX_INTR_INTERVAL) */
-  struct USB_EP_Desc* intr_ep_pool[128];
-
-  /* The mount of EPs allocated for this INTR URB */
-  int intr_ep_pool_length;
-
-  /* Pointer to info struct if URB is scheduled to be finished later */
-  struct urb_later_data* later_data;
-
-  /* Allocated bandwidth for isochronous and interrupt traffic */
-  int bandwidth;
-};
-
-
-/* This struct is for passing data from the top half to the bottom half irq
-   handlers */
-struct crisv10_irq_reg {
-  struct usb_hcd* hcd;
-  __u32 r_usb_epid_attn;
-  __u8 r_usb_status;
-  __u16 r_usb_rh_port_status_1;
-  __u16 r_usb_rh_port_status_2;
-  __u32 r_usb_irq_mask_read;
-  __u32 r_usb_fm_number;
-  struct work_struct usb_bh;
-};
-
-
-/* This struct is for passing data from the isoc top half to the isoc bottom
-   half. */
-struct crisv10_isoc_complete_data {
-  struct usb_hcd *hcd;
-  struct urb *urb;
-  struct work_struct usb_bh;
-};
-
-/* Entry item for URB lists for each endpint */
-typedef struct urb_entry
-{
-	struct urb *urb;
-	struct list_head list;
-} urb_entry_t;
-
-/* ---------------------------------------------------------------------------
-   Virtual Root HUB
-   ------------------------------------------------------------------------- */
-/* destination of request */
-#define RH_INTERFACE               0x01
-#define RH_ENDPOINT                0x02
-#define RH_OTHER                   0x03
-
-#define RH_CLASS                   0x20
-#define RH_VENDOR                  0x40
-
-/* Requests: bRequest << 8 | bmRequestType */
-#define RH_GET_STATUS           0x0080
-#define RH_CLEAR_FEATURE        0x0100
-#define RH_SET_FEATURE          0x0300
-#define RH_SET_ADDRESS		0x0500
-#define RH_GET_DESCRIPTOR	0x0680
-#define RH_SET_DESCRIPTOR       0x0700
-#define RH_GET_CONFIGURATION	0x0880
-#define RH_SET_CONFIGURATION	0x0900
-#define RH_GET_STATE            0x0280
-#define RH_GET_INTERFACE        0x0A80
-#define RH_SET_INTERFACE        0x0B00
-#define RH_SYNC_FRAME           0x0C80
-/* Our Vendor Specific Request */
-#define RH_SET_EP               0x2000
-
-
-/* Hub port features */
-#define RH_PORT_CONNECTION         0x00
-#define RH_PORT_ENABLE             0x01
-#define RH_PORT_SUSPEND            0x02
-#define RH_PORT_OVER_CURRENT       0x03
-#define RH_PORT_RESET              0x04
-#define RH_PORT_POWER              0x08
-#define RH_PORT_LOW_SPEED          0x09
-#define RH_C_PORT_CONNECTION       0x10
-#define RH_C_PORT_ENABLE           0x11
-#define RH_C_PORT_SUSPEND          0x12
-#define RH_C_PORT_OVER_CURRENT     0x13
-#define RH_C_PORT_RESET            0x14
-
-/* Hub features */
-#define RH_C_HUB_LOCAL_POWER       0x00
-#define RH_C_HUB_OVER_CURRENT      0x01
-
-#define RH_DEVICE_REMOTE_WAKEUP    0x00
-#define RH_ENDPOINT_STALL          0x01
-
-/* Our Vendor Specific feature */
-#define RH_REMOVE_EP               0x00
-
-
-#define RH_ACK                     0x01
-#define RH_REQ_ERR                 -1
-#define RH_NACK                    0x00
-
-/* Field definitions for */
-
-#define USB_IN_command__eol__BITNR      0 /* command macros */
-#define USB_IN_command__eol__WIDTH      1
-#define USB_IN_command__eol__no         0
-#define USB_IN_command__eol__yes        1
-
-#define USB_IN_command__intr__BITNR     3
-#define USB_IN_command__intr__WIDTH     1
-#define USB_IN_command__intr__no        0
-#define USB_IN_command__intr__yes       1
-
-#define USB_IN_status__eop__BITNR       1 /* status macros. */
-#define USB_IN_status__eop__WIDTH       1
-#define USB_IN_status__eop__no          0
-#define USB_IN_status__eop__yes         1
-
-#define USB_IN_status__eot__BITNR       5
-#define USB_IN_status__eot__WIDTH       1
-#define USB_IN_status__eot__no          0
-#define USB_IN_status__eot__yes         1
-
-#define USB_IN_status__error__BITNR     6
-#define USB_IN_status__error__WIDTH     1
-#define USB_IN_status__error__no        0
-#define USB_IN_status__error__yes       1
-
-#define USB_IN_status__nodata__BITNR    7
-#define USB_IN_status__nodata__WIDTH    1
-#define USB_IN_status__nodata__no       0
-#define USB_IN_status__nodata__yes      1
-
-#define USB_IN_status__epid__BITNR      8
-#define USB_IN_status__epid__WIDTH      5
-
-#define USB_EP_command__eol__BITNR      0
-#define USB_EP_command__eol__WIDTH      1
-#define USB_EP_command__eol__no         0
-#define USB_EP_command__eol__yes        1
-
-#define USB_EP_command__eof__BITNR      1
-#define USB_EP_command__eof__WIDTH      1
-#define USB_EP_command__eof__no         0
-#define USB_EP_command__eof__yes        1
-
-#define USB_EP_command__intr__BITNR     3
-#define USB_EP_command__intr__WIDTH     1
-#define USB_EP_command__intr__no        0
-#define USB_EP_command__intr__yes       1
-
-#define USB_EP_command__enable__BITNR   4
-#define USB_EP_command__enable__WIDTH   1
-#define USB_EP_command__enable__no      0
-#define USB_EP_command__enable__yes     1
-
-#define USB_EP_command__hw_valid__BITNR 5
-#define USB_EP_command__hw_valid__WIDTH 1
-#define USB_EP_command__hw_valid__no    0
-#define USB_EP_command__hw_valid__yes   1
-
-#define USB_EP_command__epid__BITNR     8
-#define USB_EP_command__epid__WIDTH     5
-
-#define USB_SB_command__eol__BITNR      0 /* command macros. */
-#define USB_SB_command__eol__WIDTH      1
-#define USB_SB_command__eol__no         0
-#define USB_SB_command__eol__yes        1
-
-#define USB_SB_command__eot__BITNR      1
-#define USB_SB_command__eot__WIDTH      1
-#define USB_SB_command__eot__no         0
-#define USB_SB_command__eot__yes        1
-
-#define USB_SB_command__intr__BITNR     3
-#define USB_SB_command__intr__WIDTH     1
-#define USB_SB_command__intr__no        0
-#define USB_SB_command__intr__yes       1
-
-#define USB_SB_command__tt__BITNR       4
-#define USB_SB_command__tt__WIDTH       2
-#define USB_SB_command__tt__zout        0
-#define USB_SB_command__tt__in          1
-#define USB_SB_command__tt__out         2
-#define USB_SB_command__tt__setup       3
-
-
-#define USB_SB_command__rem__BITNR      8
-#define USB_SB_command__rem__WIDTH      6
-
-#define USB_SB_command__full__BITNR     6
-#define USB_SB_command__full__WIDTH     1
-#define USB_SB_command__full__no        0
-#define USB_SB_command__full__yes       1
-
-#endif