move MyLoader stuff into generic files, will be used on adm5120

SVN-Revision: 13254

1 files changed, 116 insertions, 0 deletions

diff --git a/target/linux/generic-2.6/files/include/linux/myloader.h b/target/linux/generic-2.6/files/include/linux/myloader.h
new file mode 100644
index 0000000..c16c413
--- /dev/null
+++ b/target/linux/generic-2.6/files/include/linux/myloader.h
@@ -0,0 +1,116 @@
+/*
+ *  Compex's MyLoader specific definitions
+ *
+ *  Copyright (C) 2006-2008 Gabor Juhos <juhosg@openwrt.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ *
+ */
+
+#ifndef _MYLOADER_H_
+#define _MYLOADER_H_
+
+/* Myloader specific magic numbers */
+#define MYLO_MAGIC_SYS_PARAMS	0x20021107
+#define MYLO_MAGIC_PARTITIONS	0x20021103
+#define MYLO_MAGIC_BOARD_PARAMS	0x20021103
+
+/* Vendor ID's (seems to be same as the PCI vendor ID's) */
+#define VENID_COMPEX		0x11F6
+
+/* Devices based on the ADM5120 */
+#define DEVID_COMPEX_NP27G	0x0078
+#define DEVID_COMPEX_NP28G	0x044C
+#define DEVID_COMPEX_NP28GHS	0x044E
+#define DEVID_COMPEX_WP54Gv1C	0x0514
+#define DEVID_COMPEX_WP54G	0x0515
+#define DEVID_COMPEX_WP54AG	0x0546
+#define DEVID_COMPEX_WPP54AG	0x0550
+#define DEVID_COMPEX_WPP54G	0x0555
+
+/* Devices based on the Atheros AR71xx */
+#define DEVID_COMPEX_WP543	0x0640
+
+/* Devices based on the IXP422 */
+#define DEVID_COMPEX_WP18	0x047E
+#define DEVID_COMPEX_NP18A	0x0489
+
+/* Other devices */
+#define DEVID_COMPEX_NP26G8M	0x03E8
+#define DEVID_COMPEX_NP26G16M	0x03E9
+
+struct mylo_partition {
+	uint16_t	flags;	/* partition flags */
+	uint16_t	type;	/* type of the partition */
+	uint32_t	addr;	/* relative address of the partition from the
+				   flash start */
+	uint32_t	size;	/* size of the partition in bytes */
+	uint32_t	param;	/* if this is the active partition, the
+				   MyLoader load code to this address */
+};
+
+#define PARTITION_FLAG_ACTIVE	0x8000 /* this is the active partition,
+					* MyLoader loads firmware from here */
+#define PARTITION_FLAG_ISRAM	0x2000 /* FIXME: this is a RAM partition? */
+#define PARTIIION_FLAG_RAMLOAD	0x1000 /* FIXME: load this partition into the RAM? */
+#define PARTITION_FLAG_PRELOAD	0x0800 /* the partition data preloaded to RAM
+					* before decompression */
+#define PARTITION_FLAG_LZMA	0x0100 /* partition data compressed by LZMA */
+#define PARTITION_FLAG_HAVEHDR  0x0002 /* the partition data have a header */
+
+#define PARTITION_TYPE_FREE	0
+#define PARTITION_TYPE_USED	1
+
+#define MYLO_MAX_PARTITIONS	8	/* maximum number of partitions in the
+					   partition table */
+
+struct mylo_partition_table {
+	uint32_t	magic;		/* must be MYLO_MAGIC_PARTITIONS */
+	uint32_t	res0;		/* unknown/unused */
+	uint32_t	res1;		/* unknown/unused */
+	uint32_t 	res2;		/* unknown/unused */
+	struct mylo_partition partitions[MYLO_MAX_PARTITIONS];
+};
+
+struct mylo_partition_header {
+	uint32_t	len;		/* length of the partition data */
+	uint32_t	crc;		/* CRC value of the partition data */
+};
+
+struct mylo_system_params {
+	uint32_t	magic;		/* must be MYLO_MAGIC_SYS_PARAMS */
+	uint32_t	res0;
+	uint32_t	res1;
+	uint32_t	mylo_ver;
+	uint16_t	vid;		/* Vendor ID */
+	uint16_t	did;		/* Device ID */
+	uint16_t	svid;		/* Sub Vendor ID */
+	uint16_t	sdid;		/* Sub Device ID */
+	uint32_t	rev;		/* device revision */
+	uint32_t	fwhi;
+	uint32_t	fwlo;
+	uint32_t	tftp_addr;
+	uint32_t	prog_start;
+	uint32_t	flash_size;	/* size of boot FLASH in bytes */
+	uint32_t	dram_size;	/* size of onboard RAM in bytes */
+};
+
+struct mylo_eth_addr {
+	uint8_t	mac[6];
+	uint8_t	csum[2];
+};
+
+#define MYLO_ETHADDR_COUNT	8	/* maximum number of ethernet address
+					   in the board parameters */
+
+struct mylo_board_params {
+	uint32_t	magic;	/* must be MYLO_MAGIC_BOARD_PARAMS */
+	uint32_t	res0;
+	uint32_t	res1;
+	uint32_t	res2;
+	struct mylo_eth_addr addr[MYLO_ETHADDR_COUNT];
+};
+
+#endif /* _MYLOADER_H_*/