summaryrefslogtreecommitdiff
path: root/target/linux/generic-2.6
diff options
context:
space:
mode:
authorFelix Fietkau <nbd@openwrt.org>2010-03-09 14:35:41 +0000
committerFelix Fietkau <nbd@openwrt.org>2010-03-09 14:35:41 +0000
commit513e8c583f8747d2be20a0a10cf9e58b27d0e82b (patch)
tree51eb186a88ad4e37ac8f0be63ccc887832564025 /target/linux/generic-2.6
parenta5441beb82e7dde4edb1206535aa7710ba941bc4 (diff)
downloadmtk-20170518-513e8c583f8747d2be20a0a10cf9e58b27d0e82b.zip
mtk-20170518-513e8c583f8747d2be20a0a10cf9e58b27d0e82b.tar.gz
mtk-20170518-513e8c583f8747d2be20a0a10cf9e58b27d0e82b.tar.bz2
Several small fixes for ar8216 driver (patch by Jonas Gorski)
* Create defines for some magic values/masks. * Change vlan_id to u16, to allow VIDs > 255. * Add a range check to set_pvid as it isn't a VID, but the index in the vlan table. * Set the max VID to 4094, since 4095 is a reserved value and should not be used. * In mangle_rx replace the provided VID with the VID of the table entry of the port, not the index of the table. * In hw_apply, remove a redundant emptyness check (was already checked several lines above). * In no vlan mode do not set the ingress mode to secure, as there are no vlan table entries, but to use the port's destination masks. Otherwise the switch won't forward anything. * In read_status tell that the phy is up (taken from the rtl8306 driver). SVN-Revision: 20083
Diffstat (limited to 'target/linux/generic-2.6')
-rw-r--r--target/linux/generic-2.6/files/drivers/net/phy/ar8216.c31
-rw-r--r--target/linux/generic-2.6/files/drivers/net/phy/ar8216.h16
2 files changed, 35 insertions, 12 deletions
diff --git a/target/linux/generic-2.6/files/drivers/net/phy/ar8216.c b/target/linux/generic-2.6/files/drivers/net/phy/ar8216.c
index 92cc9f3..0a6eed9 100644
--- a/target/linux/generic-2.6/files/drivers/net/phy/ar8216.c
+++ b/target/linux/generic-2.6/files/drivers/net/phy/ar8216.c
@@ -42,7 +42,7 @@ struct ar8216_priv {
/* all fields below are cleared on reset */
bool vlan;
- u8 vlan_id[AR8216_NUM_VLANS];
+ u16 vlan_id[AR8216_NUM_VLANS];
u8 vlan_table[AR8216_NUM_VLANS];
u8 vlan_tagged;
u16 pvid[AR8216_NUM_PORTS];
@@ -133,6 +133,12 @@ static int
ar8216_set_pvid(struct switch_dev *dev, int port, int vlan)
{
struct ar8216_priv *priv = to_ar8216(dev);
+
+ /* make sure no invalid PVIDs get set */
+
+ if (vlan >= AR8216_NUM_VLANS)
+ return -EINVAL;
+
priv->pvid[port] = vlan;
return 0;
}
@@ -228,7 +234,7 @@ ar8216_mangle_rx(struct sk_buff *skb, int napi)
goto recv;
/* lookup port vid from local table, the switch passes an invalid vlan id */
- vlan = priv->pvid[port];
+ vlan = priv->vlan_id[priv->pvid[port]];
buf[14 + 2] &= 0xf0;
buf[14 + 2] |= vlan >> 8;
@@ -282,7 +288,7 @@ static struct switch_attr ar8216_vlan[] = {
.description = "VLAN ID",
.set = ar8216_set_vid,
.get = ar8216_get_vid,
- .max = 4095,
+ .max = 4094,
},
};
@@ -396,9 +402,6 @@ ar8216_hw_apply(struct switch_dev *dev)
portmask[i] |= vp & ~mask;
}
- if (!priv->vlan_table[j])
- continue;
-
ar8216_vtu_op(priv,
AR8216_VTU_OP_LOAD |
(priv->vlan_id[j] << AR8216_VTU_VID_S),
@@ -432,7 +435,11 @@ ar8216_hw_apply(struct switch_dev *dev)
} else {
egress = AR8216_OUT_STRIP_VLAN;
}
- ingress = AR8216_IN_SECURE;
+ if (priv->vlan) {
+ ingress = AR8216_IN_SECURE;
+ } else {
+ ingress = AR8216_IN_PORT_ONLY;
+ }
ar8216_rmw(priv, AR8216_REG_PORT_CTRL(i),
AR8216_PORT_CTRL_LEARN | AR8216_PORT_CTRL_VLAN_MODE |
@@ -478,7 +485,7 @@ ar8216_reset_switch(struct switch_dev *dev)
if (i == AR8216_PORT_CPU) {
priv->write(priv, AR8216_REG_PORT_STATUS(i),
AR8216_PORT_STATUS_LINK_UP |
- AR8216_PORT_STATUS_SPEED |
+ AR8216_PORT_SPEED_100M |
AR8216_PORT_STATUS_TXMAC |
AR8216_PORT_STATUS_RXMAC |
AR8216_PORT_STATUS_DUPLEX);
@@ -554,6 +561,10 @@ ar8216_read_status(struct phy_device *phydev)
priv->write(priv, AR8216_REG_ATU, AR8216_ATU_OP_FLUSH);
+ phydev->state = PHY_RUNNING;
+ netif_carrier_on(phydev->attached_dev);
+ phydev->adjust_link(phydev->attached_dev);
+
return 0;
}
@@ -573,8 +584,8 @@ ar8216_probe(struct phy_device *pdev)
priv.phy = pdev;
val = ar8216_mii_read(&priv, AR8216_REG_CTRL);
- rev = val & 0xff;
- id = (val >> 8) & 0xff;
+ rev = val & AR8216_CTRL_REVISION;
+ id = (val & AR8216_CTRL_VERSION) >> AR8216_CTRL_VERSION_S;
if ((id != 1) || (rev != 1))
return -ENODEV;
diff --git a/target/linux/generic-2.6/files/drivers/net/phy/ar8216.h b/target/linux/generic-2.6/files/drivers/net/phy/ar8216.h
index 741dce9..c1b8fdb 100644
--- a/target/linux/generic-2.6/files/drivers/net/phy/ar8216.h
+++ b/target/linux/generic-2.6/files/drivers/net/phy/ar8216.h
@@ -24,6 +24,10 @@
#define AR8216_NUM_VLANS 16
#define AR8216_REG_CTRL 0x0000
+#define AR8216_CTRL_REVISION BITS(0, 8)
+#define AR8216_CTRL_REVISION_S 0
+#define AR8216_CTRL_VERSION BITS(8, 8)
+#define AR8216_CTRL_VERSION_S 8
#define AR8216_CTRL_RESET BIT(31)
#define AR8216_REG_GLOBAL_CTRL 0x0030
@@ -73,8 +77,8 @@
#define AR8216_PORT_OFFSET(_i) (0x0100 * (_i + 1))
#define AR8216_REG_PORT_STATUS(_i) (AR8216_PORT_OFFSET(_i) + 0x0000)
-#define AR8216_PORT_STATUS_SPEED BIT(0)
-#define AR8216_PORT_STATUS_SPEED_ERR BIT(1)
+#define AR8216_PORT_STATUS_SPEED BITS(0,2)
+#define AR8216_PORT_STATUS_SPEED_S 0
#define AR8216_PORT_STATUS_TXMAC BIT(2)
#define AR8216_PORT_STATUS_RXMAC BIT(3)
#define AR8216_PORT_STATUS_TXFLOW BIT(4)
@@ -126,6 +130,14 @@
#define AR8216_REG_PORT_RATE(_i) (AR8216_PORT_OFFSET(_i) + 0x000c)
#define AR8216_REG_PORT_PRIO(_i) (AR8216_PORT_OFFSET(_i) + 0x0010)
+/* port speed */
+enum {
+ AR8216_PORT_SPEED_10M = 0,
+ AR8216_PORT_SPEED_100M = 1,
+ AR8216_PORT_SPEED_1000M = 2,
+ AR8216_PORT_SPEED_ERR = 3,
+};
+
/* ingress 802.1q mode */
enum {
AR8216_IN_PORT_ONLY = 0,