summaryrefslogtreecommitdiff
path: root/target/linux/ipq806x/base-files
diff options
context:
space:
mode:
authorDongming Han <handongming@gl-inet.com>2017-12-07 20:48:19 +0800
committerJohn Crispin <john@phrozen.org>2018-02-14 09:40:32 +0100
commit04d3308b6248ef21a6f0bc3378b342906c2d2865 (patch)
tree9180681b935ec6494df250411112327f07e9ef9f /target/linux/ipq806x/base-files
parent88a41074e8e7012c2cb73b85263425c4c474beb1 (diff)
downloadmtk-20170518-04d3308b6248ef21a6f0bc3378b342906c2d2865.zip
mtk-20170518-04d3308b6248ef21a6f0bc3378b342906c2d2865.tar.gz
mtk-20170518-04d3308b6248ef21a6f0bc3378b342906c2d2865.tar.bz2
ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300 Specification: - SOC: IPQ4028 / QCA Dakota - RAM: 256 MiB - FLASH: 32 MiB - ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN) - USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) - WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2 - WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2 - INPUT: one reset and one WPS button - LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved - UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1 Installation: Method 1: - use serial port to stop uboot - uboot command: run lf Method 2: - push down reset button and power on - wait until three leds constantly on then release - upgrade by uboot web at http://192.168.1.1 Note: - the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method. - the sysupgrade image can be automatically downloaded if tftp server at 192.168.1.2 have that file. - the wifi led will be flashing when writing image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
Diffstat (limited to 'target/linux/ipq806x/base-files')
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/01_leds3
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata2
3 files changed, 6 insertions, 0 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index b04832f..ea8b781 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -16,6 +16,9 @@ avm,fritzbox-4040)
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
;;
+glinet,gl-b1300)
+ ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
+ ;;
netgear,d7800 |\
netgear,r7500 |\
netgear,r7500v2 |\
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 580c1d8..74223e5 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -33,6 +33,7 @@ tplink,vr2600v)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
;;
+glinet,gl-b1300 |\
openmesh,a42)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 61b7403..fa8eb11 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -53,6 +53,7 @@ case "$FIRMWARE" in
openmesh,a42)
ath10kcal_extract "0:ART" 4096 12064
;;
+ glinet,gl-b1300 |\
qcom,ap-dk01.1-c1)
ath10kcal_extract "ART" 4096 12064
;;
@@ -66,6 +67,7 @@ case "$FIRMWARE" in
openmesh,a42)
ath10kcal_extract "0:ART" 20480 12064
;;
+ glinet,gl-b1300 |\
qcom,ap-dk01.1-c1)
ath10kcal_extract "ART" 20480 12064
;;