ipq806x/nbg6817: add support for ZyXEL NBG6817

CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>

1 files changed, 341 insertions, 0 deletions

diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
new file mode 100644
index 0000000..cc56213
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
@@ -0,0 +1,341 @@
+#include "qcom-ipq8065-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "ZyXEL NBG6817";
+	compatible = "zyxel,nbg6817", "qcom,ipq8065";
+
+	memory@0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+		sdcc1 = &sdcc1;
+	};
+
+	chosen {
+		bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux@800000 {
+			pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
+			pinctrl-names = "default";
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				clk {
+					pins = "gpio1";
+					input-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				tx {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+					input-disable;
+				};
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					drive-strength = <10>;
+					bias-none;
+				};
+
+				cs {
+					pins = "gpio20";
+					drive-strength = <12>;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial@16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi4: spi@1a280000 {
+				status = "ok";
+				spi-max-frequency = <50000000>;
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				flash: m25p80@0 {
+					compatible = "s25fl512s";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <51200000>;
+					reg = <0>;
+
+					linux,part-probe = "qcom-smem";
+				};
+			};
+		};
+
+		phy@100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy@100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy@110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy@110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30@0 {
+			status = "ok";
+		};
+
+		usb30@1 {
+			status = "ok";
+		};
+
+		pcie0: pci@1b500000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie1: pci@1b700000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+
+			phy0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					0x00970 0x1e864443  /* QM_PORT0_CTRL0 */
+					0x00974 0x000001c6  /* QM_PORT0_CTRL1 */
+					0x00978 0x19008643  /* QM_PORT1_CTRL0 */
+					0x0097c 0x000001c6  /* QM_PORT1_CTRL1 */
+					0x00980 0x19008643  /* QM_PORT2_CTRL0 */
+					0x00984 0x000001c6  /* QM_PORT2_CTRL1 */
+					0x00988 0x19008643  /* QM_PORT3_CTRL0 */
+					0x0098c 0x000001c6  /* QM_PORT3_CTRL1 */
+					0x00990 0x19008643  /* QM_PORT4_CTRL0 */
+					0x00994 0x000001c6  /* QM_PORT4_CTRL1 */
+					0x00998 0x1e864443  /* QM_PORT5_CTRL0 */
+					0x0099c 0x000001c6  /* QM_PORT5_CTRL1 */
+					0x009a0 0x1e864443  /* QM_PORT6_CTRL0 */
+					0x009a4 0x000001c6  /* QM_PORT6_CTRL1 */
+					>;
+			};
+
+			phy4: ethernet-phy@4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+				qca,ar8327-initvals = <
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x0000c 0x80        /* PAD6_MODE */
+					>;
+			};
+		};
+
+		gmac1: ethernet@37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+			qcom,phy_mdio_addr = <4>;
+			qcom,poll_required = <0>;
+			qcom,rgmii_delay = <1>;
+			qcom,phy_mii_type = <0>;
+			qcom,emulation = <0>;
+			qcom,irq = <255>;
+			mdiobus = <&mdio0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet@37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+			qcom,phy_mdio_addr = <0>;	/* none */
+			qcom,poll_required = <0>;	/* no polling */
+			qcom,rgmii_delay = <0>;
+			qcom,phy_mii_type = <1>;
+			qcom,emulation = <0>;
+			qcom,irq = <258>;
+			mdiobus = <&mdio0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm@108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+
+		amba {
+			sdcc1: sdcc@12400000 {
+				status          = "okay";
+                                dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+                                dma-names = "tx", "rx";
+			};
+		};
+
+
+
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		internet {
+			label = "nbg6817:white:internet";
+			gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+		};
+
+		power {
+			label = "nbg6817:white:power";
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		wifi {
+			label = "nbg6817:amber:wifi";
+			gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+		};
+
+		wifi5g {
+			label = "nbg6817:amber:wifi5g";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio_export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		usb0_status {
+			gpio-export,name = "usb0";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb1_status {
+			gpio-export,name = "usb1";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+		};
+		usb1_power {
+			gpio-export,name = "usb1_power";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
+		};
+		usb2_power {
+			gpio-export,name = "usb2_power";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};