linux/ixp4xx: add preliminary 2.6.37 kernel support

SVN-Revision: 23964

40 files changed, 6339 insertions, 0 deletions

diff --git a/target/linux/ixp4xx/patches-2.6.37/020-gateworks_i2c_pld.patch b/target/linux/ixp4xx/patches-2.6.37/020-gateworks_i2c_pld.patch
new file mode 100644
index 0000000..6c93c44
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/020-gateworks_i2c_pld.patch
@@ -0,0 +1,421 @@
+--- /dev/null
++++ b/drivers/gpio/gw_i2c_pld.c
+@@ -0,0 +1,371 @@
++/*
++ * Gateworks I2C PLD GPIO expander
++ *
++ * Copyright (C) 2009 Gateworks Corporation
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
++ */
++
++#include <linux/kernel.h>
++#include <linux/slab.h>
++#include <linux/hardirq.h>
++#include <linux/i2c.h>
++#include <linux/i2c/gw_i2c_pld.h>
++#include <asm/gpio.h>
++
++static const struct i2c_device_id gw_i2c_pld_id[] = {
++	{ "gw_i2c_pld", 8 },
++	{ }
++};
++MODULE_DEVICE_TABLE(i2c, gw_i2c_pld_id);
++
++/*
++ * The Gateworks I2C PLD chip only expose one read and one
++ * write register.  Writing a "one" bit (to match the reset state) lets
++ * that pin be used as an input. It is an open-drain model.
++ */
++
++struct gw_i2c_pld {
++	struct gpio_chip	chip;
++	struct i2c_client	*client;
++	unsigned		out;		/* software latch */
++};
++
++/*-------------------------------------------------------------------------*/
++
++/*
++ * The Gateworks I2C PLD chip does not properly send the acknowledge bit
++ * thus we cannot use standard i2c_smbus functions. We have recreated
++ * our own here, but we still use the mutex_lock to lock the i2c_bus
++ * as the device still exists on the I2C bus.
++*/
++
++#define PLD_SCL_GPIO 6
++#define PLD_SDA_GPIO 7
++
++#define SCL_LO()  gpio_line_set(PLD_SCL_GPIO, IXP4XX_GPIO_LOW)
++#define SCL_HI()  gpio_line_set(PLD_SCL_GPIO, IXP4XX_GPIO_HIGH)
++#define SCL_EN()  gpio_line_config(PLD_SCL_GPIO, IXP4XX_GPIO_OUT)
++#define SDA_LO()  gpio_line_set(PLD_SDA_GPIO, IXP4XX_GPIO_LOW)
++#define SDA_HI()  gpio_line_set(PLD_SDA_GPIO, IXP4XX_GPIO_HIGH)
++#define SDA_EN()  gpio_line_config(PLD_SDA_GPIO, IXP4XX_GPIO_OUT)
++#define SDA_DIS() gpio_line_config(PLD_SDA_GPIO, IXP4XX_GPIO_IN)
++#define SDA_IN(x) gpio_line_get(PLD_SDA_GPIO, &x);
++
++static int i2c_pld_write_byte(int address, int byte)
++{
++	int i;
++
++	address = (address << 1) & ~0x1;
++
++	SDA_HI();
++	SDA_EN();
++	SCL_EN();
++	SCL_HI();
++	SDA_LO();
++	SCL_LO();
++
++	for (i = 7; i >= 0; i--)
++	{
++		if (address & (1 << i))
++			SDA_HI();
++		else
++			SDA_LO();
++
++		SCL_HI();
++		SCL_LO();
++	}
++
++	SDA_DIS();
++	SCL_HI();
++	SDA_IN(i);
++	SCL_LO();
++	SDA_EN();
++
++	for (i = 7; i >= 0; i--)
++	{
++		if (byte & (1 << i))
++      SDA_HI();
++		else
++			SDA_LO();
++		SCL_HI();
++		SCL_LO();
++	}
++
++	SDA_DIS();
++	SCL_HI();
++	SDA_IN(i);
++	SCL_LO();
++
++	SDA_HI();
++	SDA_EN();
++
++	SDA_LO();
++	SCL_HI();
++	SDA_HI();
++	SCL_LO();
++	SCL_HI();
++
++	return 0;
++}
++
++static unsigned int i2c_pld_read_byte(int address)
++{
++	int i = 0, byte = 0;
++	int bit;
++
++	address = (address << 1) | 0x1;
++
++	SDA_HI();
++	SDA_EN();
++	SCL_EN();
++	SCL_HI();
++	SDA_LO();
++	SCL_LO();
++
++	for (i = 7; i >= 0; i--)
++	{
++		if (address & (1 << i))
++			SDA_HI();
++		else
++			SDA_LO();
++
++		SCL_HI();
++		SCL_LO();
++	}
++
++	SDA_DIS();
++	SCL_HI();
++	SDA_IN(i);
++	SCL_LO();
++	SDA_EN();
++
++	SDA_DIS();
++	for (i = 7; i >= 0; i--)
++	{
++		SCL_HI();
++		SDA_IN(bit);
++		byte |= bit << i;
++		SCL_LO();
++	}
++
++	SDA_LO();
++	SCL_HI();
++	SDA_HI();
++	SCL_LO();
++	SCL_HI();
++
++	return byte;
++}
++
++
++static int gw_i2c_pld_input8(struct gpio_chip *chip, unsigned offset)
++{
++	int ret;
++	struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip);
++	struct i2c_adapter *adap = gpio->client->adapter;
++	
++	if (in_atomic() || irqs_disabled()) {
++		ret = mutex_trylock(&adap->bus_lock);
++		if (!ret)
++			/* I2C activity is ongoing. */
++			return -EAGAIN;
++	} else {
++		mutex_lock_nested(&adap->bus_lock, adap->level);
++	}
++
++	gpio->out |= (1 << offset);
++
++	ret = i2c_pld_write_byte(gpio->client->addr, gpio->out);
++
++	mutex_unlock(&adap->bus_lock);
++
++	return ret;
++}
++
++static int gw_i2c_pld_get8(struct gpio_chip *chip, unsigned offset)
++{
++	int ret;
++	s32	value;
++	struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip);
++	struct i2c_adapter *adap = gpio->client->adapter;
++	
++	if (in_atomic() || irqs_disabled()) {
++		ret = mutex_trylock(&adap->bus_lock);
++		if (!ret)
++			/* I2C activity is ongoing. */
++			return -EAGAIN;
++	} else {
++		mutex_lock_nested(&adap->bus_lock, adap->level);
++	}
++
++	value = i2c_pld_read_byte(gpio->client->addr);
++
++	mutex_unlock(&adap->bus_lock);
++
++	return (value < 0) ? 0 : (value & (1 << offset));
++}
++
++static int gw_i2c_pld_output8(struct gpio_chip *chip, unsigned offset, int value)
++{
++	int ret;
++
++	struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip);
++	struct i2c_adapter *adap = gpio->client->adapter;
++
++	unsigned bit = 1 << offset;
++	
++	if (in_atomic() || irqs_disabled()) {
++		ret = mutex_trylock(&adap->bus_lock);
++		if (!ret)
++			/* I2C activity is ongoing. */
++			return -EAGAIN;
++	} else {
++		mutex_lock_nested(&adap->bus_lock, adap->level);
++	}
++
++
++	if (value)
++		gpio->out |= bit;
++	else
++		gpio->out &= ~bit;
++
++	ret = i2c_pld_write_byte(gpio->client->addr, gpio->out);
++
++	mutex_unlock(&adap->bus_lock);
++
++	return ret;
++}
++
++static void gw_i2c_pld_set8(struct gpio_chip *chip, unsigned offset, int value)
++{
++	gw_i2c_pld_output8(chip, offset, value);
++}
++
++/*-------------------------------------------------------------------------*/
++
++static int gw_i2c_pld_probe(struct i2c_client *client,
++			 const struct i2c_device_id *id)
++{
++	struct gw_i2c_pld_platform_data	*pdata;
++	struct gw_i2c_pld *gpio;
++	int status;
++
++	pdata = client->dev.platform_data;
++	if (!pdata)
++		return -ENODEV;
++
++	/* Allocate, initialize, and register this gpio_chip. */
++	gpio = kzalloc(sizeof *gpio, GFP_KERNEL);
++	if (!gpio)
++		return -ENOMEM;
++
++	gpio->chip.base = pdata->gpio_base;
++	gpio->chip.can_sleep = 1;
++	gpio->chip.dev = &client->dev;
++	gpio->chip.owner = THIS_MODULE;
++
++	gpio->chip.ngpio = pdata->nr_gpio;
++	gpio->chip.direction_input = gw_i2c_pld_input8;
++	gpio->chip.get = gw_i2c_pld_get8;
++	gpio->chip.direction_output = gw_i2c_pld_output8;
++	gpio->chip.set = gw_i2c_pld_set8;
++
++	gpio->chip.label = client->name;
++
++	gpio->client = client;
++	i2c_set_clientdata(client, gpio);
++
++	gpio->out = 0xFF;
++
++	status = gpiochip_add(&gpio->chip);
++	if (status < 0)
++		goto fail;
++
++	dev_info(&client->dev, "gpios %d..%d on a %s%s\n",
++			gpio->chip.base,
++			gpio->chip.base + gpio->chip.ngpio - 1,
++			client->name,
++			client->irq ? " (irq ignored)" : "");
++
++	/* Let platform code set up the GPIOs and their users.
++	 * Now is the first time anyone could use them.
++	 */
++	if (pdata->setup) {
++		status = pdata->setup(client,
++				gpio->chip.base, gpio->chip.ngpio,
++				pdata->context);
++		if (status < 0)
++			dev_warn(&client->dev, "setup --> %d\n", status);
++	}
++
++	return 0;
++
++fail:
++	dev_dbg(&client->dev, "probe error %d for '%s'\n",
++			status, client->name);
++	kfree(gpio);
++	return status;
++}
++
++static int gw_i2c_pld_remove(struct i2c_client *client)
++{
++	struct gw_i2c_pld_platform_data	*pdata = client->dev.platform_data;
++	struct gw_i2c_pld *gpio = i2c_get_clientdata(client);
++	int				status = 0;
++
++	if (pdata->teardown) {
++		status = pdata->teardown(client,
++				gpio->chip.base, gpio->chip.ngpio,
++				pdata->context);
++		if (status < 0) {
++			dev_err(&client->dev, "%s --> %d\n",
++					"teardown", status);
++			return status;
++		}
++	}
++
++	status = gpiochip_remove(&gpio->chip);
++	if (status == 0)
++		kfree(gpio);
++	else
++		dev_err(&client->dev, "%s --> %d\n", "remove", status);
++	return status;
++}
++
++static struct i2c_driver gw_i2c_pld_driver = {
++	.driver = {
++		.name	= "gw_i2c_pld",
++		.owner	= THIS_MODULE,
++	},
++	.probe	= gw_i2c_pld_probe,
++	.remove	= gw_i2c_pld_remove,
++	.id_table = gw_i2c_pld_id,
++};
++
++static int __init gw_i2c_pld_init(void)
++{
++	return i2c_add_driver(&gw_i2c_pld_driver);
++}
++module_init(gw_i2c_pld_init);
++
++static void __exit gw_i2c_pld_exit(void)
++{
++	i2c_del_driver(&gw_i2c_pld_driver);
++}
++module_exit(gw_i2c_pld_exit);
++
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("Chris Lang");
+--- a/drivers/gpio/Kconfig
++++ b/drivers/gpio/Kconfig
+@@ -348,6 +348,14 @@ config GPIO_RDC321X
+ 	  Support for the RDC R321x SoC GPIOs over southbridge
+ 	  PCI configuration space.
+ 
++config GPIO_GW_I2C_PLD
++	tristate "Gateworks I2C PLD GPIO Expander"
++	depends on I2C
++	help
++		Say yes here to provide access to the Gateworks I2C PLD GPIO
++		Expander. This is used at least on the GW2358-4.
++
++
+ comment "SPI GPIO expanders:"
+ 
+ config GPIO_MAX7301
+--- a/drivers/gpio/Makefile
++++ b/drivers/gpio/Makefile
+@@ -41,3 +41,4 @@ obj-$(CONFIG_GPIO_RDC321X)	+= rdc321x-gp
+ obj-$(CONFIG_GPIO_JANZ_TTL)	+= janz-ttl.o
+ obj-$(CONFIG_GPIO_SX150X)	+= sx150x.o
+ obj-$(CONFIG_GPIO_VX855)	+= vx855_gpio.o
++obj-$(CONFIG_GPIO_GW_I2C_PLD)	+= gw_i2c_pld.o
+--- /dev/null
++++ b/include/linux/i2c/gw_i2c_pld.h
+@@ -0,0 +1,20 @@
++#ifndef __LINUX_GW_I2C_PLD_H
++#define __LINUX_GW_I2C_PLD_H
++
++/**
++ * The Gateworks I2C PLD Implements an additional 8 bits of GPIO through the PLD
++ */
++
++struct gw_i2c_pld_platform_data {
++	unsigned gpio_base;
++	unsigned nr_gpio;
++	int		(*setup)(struct i2c_client *client,
++					int gpio, unsigned ngpio,
++					void *context);
++	int		(*teardown)(struct i2c_client *client,
++					int gpio, unsigned ngpio,
++					void *context);
++	void		*context;
++};
++
++#endif /* __LINUX_GW_I2C_PLD_H */
diff --git a/target/linux/ixp4xx/patches-2.6.37/090-increase_entropy_pools.patch b/target/linux/ixp4xx/patches-2.6.37/090-increase_entropy_pools.patch
new file mode 100644
index 0000000..1a44660
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/090-increase_entropy_pools.patch
@@ -0,0 +1,15 @@
+--- a/drivers/char/random.c
++++ b/drivers/char/random.c
+@@ -264,9 +264,9 @@
+ /*
+  * Configuration information
+  */
+-#define INPUT_POOL_WORDS 128
+-#define OUTPUT_POOL_WORDS 32
+-#define SEC_XFER_SIZE 512
++#define INPUT_POOL_WORDS 256
++#define OUTPUT_POOL_WORDS 64
++#define SEC_XFER_SIZE 1024
+ #define EXTRACT_SIZE 10
+ 
+ /*
diff --git a/target/linux/ixp4xx/patches-2.6.37/100-wg302v2_gateway7001_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.37/100-wg302v2_gateway7001_mac_plat_info.patch
new file mode 100644
index 0000000..c664eda
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/100-wg302v2_gateway7001_mac_plat_info.patch
@@ -0,0 +1,68 @@
+--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
++++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
+@@ -75,9 +75,35 @@ static struct platform_device gateway700
+ 	.resource	= &gateway7001_uart_resource,
+ };
+ 
++static struct eth_plat_info gateway7001_plat_eth[] = {
++	{
++		.phy		= 1,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}, {
++		.phy		= 2,
++		.rxq		= 4,
++		.txreadyq	= 21,
++	}
++};
++
++static struct platform_device gateway7001_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= gateway7001_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= gateway7001_plat_eth + 1,
++	}
++};
++
+ static struct platform_device *gateway7001_devices[] __initdata = {
+ 	&gateway7001_flash,
+-	&gateway7001_uart
++	&gateway7001_uart,
++	&gateway7001_eth[0],
++	&gateway7001_eth[1],
+ };
+ 
+ static void __init gateway7001_init(void)
+--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
++++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
+@@ -76,9 +76,26 @@ static struct platform_device wg302v2_ua
+ 	.resource	= &wg302v2_uart_resource,
+ };
+ 
++static struct eth_plat_info wg302v2_plat_eth[] = {
++	{
++		.phy		= 8,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}
++};
++
++static struct platform_device wg302v2_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= wg302v2_plat_eth,
++	}
++};
++
+ static struct platform_device *wg302v2_devices[] __initdata = {
+ 	&wg302v2_flash,
+ 	&wg302v2_uart,
++	&wg302v2_eth[0],
+ };
+ 
+ static void __init wg302v2_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.37/105-wg302v1_support.patch b/target/linux/ixp4xx/patches-2.6.37/105-wg302v1_support.patch
new file mode 100644
index 0000000..6e12caa
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/105-wg302v1_support.patch
@@ -0,0 +1,257 @@
+--- a/arch/arm/configs/ixp4xx_defconfig
++++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -13,6 +13,7 @@ CONFIG_MACH_AVILA=y
+ CONFIG_MACH_LOFT=y
+ CONFIG_ARCH_ADI_COYOTE=y
+ CONFIG_MACH_GATEWAY7001=y
++CONFIG_MACH_WG302V1=y
+ CONFIG_MACH_WG302V2=y
+ CONFIG_ARCH_IXDP425=y
+ CONFIG_MACH_IXDPG425=y
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -49,6 +49,14 @@ config MACH_GATEWAY7001
+ 	  7001 Access Point. For more information on this platform,
+ 	  see http://openwrt.org
+ 
++config MACH_WG302V1
++	bool "Netgear WG302 v1 / WAG302 v1"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support Netgear's
++	  WG302 v1 or WAG302 v1 Access Points. For more information
++	  on this platform, see http://openwrt.org
++
+ config MACH_WG302V2
+ 	bool "Netgear WG302 v2 / WAG302 v2"
+ 	select PCI
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -14,6 +14,7 @@ obj-pci-$(CONFIG_MACH_NSLU2)		+= nslu2-p
+ obj-pci-$(CONFIG_MACH_NAS100D)		+= nas100d-pci.o
+ obj-pci-$(CONFIG_MACH_DSMG600)		+= dsmg600-pci.o
+ obj-pci-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-pci.o
++obj-pci-$(CONFIG_MACH_WG302V1)		+= wg302v1-pci.o
+ obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302v2-pci.o
+ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ obj-pci-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-pci.o
+@@ -29,6 +30,7 @@ obj-$(CONFIG_MACH_NSLU2)	+= nslu2-setup.
+ obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o
+ obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o
+ obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
++obj-$(CONFIG_MACH_WG302V1)	+= wg302v1-setup.o
+ obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
+ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+ obj-$(CONFIG_MACH_GORAMO_MLR)	+= goramo_mlr.o
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c
+@@ -0,0 +1,64 @@
++/*
++ * arch/arch/mach-ixp4xx/wg302v1-pci.c
++ *
++ * PCI setup routines for the Netgear WG302 v1 and WAG302 v1
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Software, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++
++#include <asm/mach/pci.h>
++
++void __init wg302v1_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init wg302v1_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 1)
++		return IRQ_IXP4XX_GPIO8;
++	else if (slot == 2)
++		return IRQ_IXP4XX_GPIO10;
++	else
++		return -1;
++}
++
++struct hw_pci wg302v1_pci __initdata = {
++	.nr_controllers = 1,
++	.preinit =        wg302v1_pci_preinit,
++	.swizzle =        pci_std_swizzle,
++	.setup =          ixp4xx_setup,
++	.scan =           ixp4xx_scan_bus,
++	.map_irq =        wg302v1_map_irq,
++};
++
++int __init wg302v1_pci_init(void)
++{
++	if (machine_is_wg302v1())
++		pci_common_init(&wg302v1_pci);
++	return 0;
++}
++
++subsys_initcall(wg302v1_pci_init);
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
+@@ -0,0 +1,142 @@
++/*
++ * arch/arm/mach-ixp4xx/wg302v1-setup.c
++ *
++ * Board setup for the Netgear WG302 v1 and WAG302 v1
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <kaloz@openwrt.org>
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++#include <linux/types.h>
++#include <linux/memory.h>
++
++#include <asm/setup.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data wg302v1_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource wg302v1_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device wg302v1_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &wg302v1_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &wg302v1_flash_resource,
++};
++
++static struct resource wg302v1_uart_resources[] = {
++	{
++		.start	= IXP4XX_UART1_BASE_PHYS,
++		.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags	= IORESOURCE_MEM,
++	},
++	{
++		.start	= IXP4XX_UART2_BASE_PHYS,
++		.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags	= IORESOURCE_MEM,
++	}
++};
++
++static struct plat_serial8250_port wg302v1_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device wg302v1_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev			= {
++		.platform_data	= wg302v1_uart_data,
++	},
++	.num_resources	= 2,
++	.resource	= wg302v1_uart_resources,
++};
++
++static struct eth_plat_info wg302v1_plat_eth[] = {
++	{
++		.phy		= 30,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}
++};
++
++static struct platform_device wg302v1_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= wg302v1_plat_eth,
++	}
++};
++
++static struct platform_device *wg302v1_devices[] __initdata = {
++	&wg302v1_flash,
++	&wg302v1_uart,
++	&wg302v1_eth[0],
++};
++
++static void __init wg302v1_init(void)
++{
++	ixp4xx_sys_init();
++
++	wg302v1_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	wg302v1_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++	platform_add_devices(wg302v1_devices, ARRAY_SIZE(wg302v1_devices));
++}
++
++#ifdef CONFIG_MACH_WG302V1
++MACHINE_START(WG302V1, "Netgear WG302 v1 / WAG302 v1")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= wg302v1_init,
++MACHINE_END
++#endif
diff --git a/target/linux/ixp4xx/patches-2.6.37/110-pronghorn_series_support.patch b/target/linux/ixp4xx/patches-2.6.37/110-pronghorn_series_support.patch
new file mode 100644
index 0000000..f3e088b
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/110-pronghorn_series_support.patch
@@ -0,0 +1,387 @@
+--- a/arch/arm/configs/ixp4xx_defconfig
++++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -15,6 +15,8 @@ CONFIG_ARCH_ADI_COYOTE=y
+ CONFIG_MACH_GATEWAY7001=y
+ CONFIG_MACH_WG302V1=y
+ CONFIG_MACH_WG302V2=y
++CONFIG_MACH_PRONGHORN=y
++CONFIG_MACH_PRONGHORNMETRO=y
+ CONFIG_ARCH_IXDP425=y
+ CONFIG_MACH_IXDPG425=y
+ CONFIG_MACH_IXDP465=y
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -65,6 +65,22 @@ config MACH_WG302V2
+ 	  WG302 v2 or WAG302 v2 Access Points. For more information
+ 	  on this platform, see http://openwrt.org
+ 
++config MACH_PRONGHORN
++	bool "ADI Pronghorn series"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support the ADI 
++	  Engineering Pronghorn series. For more
++	  information on this platform, see http://www.adiengineering.com
++
++#
++# There're only minimal differences kernel-wise between the Pronghorn and
++# Pronghorn Metro boards - they use different chip selects to drive the
++# CF slot connected to the expansion bus, so we just enable them together.
++#
++config MACH_PRONGHORNMETRO
++	def_bool MACH_PRONGHORN
++
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -18,6 +18,7 @@ obj-pci-$(CONFIG_MACH_WG302V1)		+= wg302
+ obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302v2-pci.o
+ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ obj-pci-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-pci.o
++obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -35,6 +36,7 @@ obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-se
+ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+ obj-$(CONFIG_MACH_GORAMO_MLR)	+= goramo_mlr.o
+ obj-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-setup.o
++obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/pronghorn-pci.c
+@@ -0,0 +1,70 @@
++/*
++ * arch/arch/mach-ixp4xx/pronghorn-pci.c
++ *
++ * PCI setup routines for ADI Engineering Pronghorn series
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++
++#include <asm/mach/pci.h>
++
++void __init pronghorn_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init pronghorn_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 13)
++		return IRQ_IXP4XX_GPIO4;
++	else if (slot == 14)
++		return IRQ_IXP4XX_GPIO6;
++	else if (slot == 15)
++		return IRQ_IXP4XX_GPIO11;
++	else if (slot == 16)
++		return IRQ_IXP4XX_GPIO1;
++	else
++		return -1;
++}
++
++struct hw_pci pronghorn_pci __initdata = {
++	.nr_controllers	= 1,
++	.preinit	= pronghorn_pci_preinit,
++	.swizzle	= pci_std_swizzle,
++	.setup		= ixp4xx_setup,
++	.scan		= ixp4xx_scan_bus,
++	.map_irq	= pronghorn_map_irq,
++};
++
++int __init pronghorn_pci_init(void)
++{
++	if (machine_is_pronghorn() || machine_is_pronghorn_metro())
++		pci_common_init(&pronghorn_pci);
++	return 0;
++}
++
++subsys_initcall(pronghorn_pci_init);
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
+@@ -0,0 +1,245 @@
++/*
++ * arch/arm/mach-ixp4xx/pronghorn-setup.c
++ *
++ * Board setup for the ADI Engineering Pronghorn series
++ *
++ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
++ *
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <Kaloz@openwrt.org>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++#include <linux/types.h>
++#include <linux/memory.h>
++#include <linux/i2c-gpio.h>
++#include <linux/leds.h>
++
++#include <asm/setup.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data pronghorn_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource pronghorn_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device pronghorn_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data	= &pronghorn_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &pronghorn_flash_resource,
++};
++
++static struct resource pronghorn_uart_resources [] = {
++	{
++		.start		= IXP4XX_UART1_BASE_PHYS,
++		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	},
++	{
++		.start		= IXP4XX_UART2_BASE_PHYS,
++		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	}
++};
++
++static struct plat_serial8250_port pronghorn_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device pronghorn_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev		= {
++		.platform_data	= pronghorn_uart_data,
++	},
++	.num_resources	= 2,
++	.resource	= pronghorn_uart_resources,
++};
++
++static struct i2c_gpio_platform_data pronghorn_i2c_gpio_data = {
++	.sda_pin	= 9,
++	.scl_pin	= 10,
++};
++
++static struct platform_device pronghorn_i2c_gpio = {
++	.name		= "i2c-gpio",
++	.id		= 0,
++	.dev		= {
++		.platform_data	= &pronghorn_i2c_gpio_data,
++	},
++};
++
++static struct gpio_led pronghorn_led_pin[] = {
++	{
++		.name		= "pronghorn:green:status",
++		.gpio		= 7,
++	}
++};
++
++static struct gpio_led_platform_data pronghorn_led_data = {
++	.num_leds		= 1,
++	.leds			= pronghorn_led_pin,
++};
++
++static struct platform_device pronghorn_led = {
++	.name			= "leds-gpio",
++	.id			= -1,
++	.dev.platform_data	= &pronghorn_led_data,
++};
++
++static struct resource pronghorn_pata_resources[] = {
++	{
++		.flags	= IORESOURCE_MEM
++	},
++	{
++		.flags	= IORESOURCE_MEM,
++	},
++	{
++		.name	= "intrq",
++		.start	= IRQ_IXP4XX_GPIO0,
++		.end	= IRQ_IXP4XX_GPIO0,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct ixp4xx_pata_data pronghorn_pata_data = {
++	.cs0_bits	= 0xbfff0043,
++	.cs1_bits	= 0xbfff0043,
++};
++
++static struct platform_device pronghorn_pata = {
++	.name			= "pata_ixp4xx_cf",
++	.id			= 0,
++	.dev.platform_data      = &pronghorn_pata_data,
++	.num_resources		= ARRAY_SIZE(pronghorn_pata_resources),
++	.resource		= pronghorn_pata_resources,
++};
++
++static struct eth_plat_info pronghorn_plat_eth[] = {
++	{
++		.phy		= 0,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}, {
++		.phy		= 1,
++		.rxq		= 4,
++		.txreadyq	= 21,
++	}
++};
++
++static struct platform_device pronghorn_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= pronghorn_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= pronghorn_plat_eth + 1,
++	}
++};
++
++static struct platform_device *pronghorn_devices[] __initdata = {
++	&pronghorn_flash,
++	&pronghorn_uart,
++	&pronghorn_led,
++	&pronghorn_eth[0],
++	&pronghorn_eth[1],
++};
++
++static void __init pronghorn_init(void)
++{
++	ixp4xx_sys_init();
++
++	pronghorn_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	pronghorn_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++	platform_add_devices(pronghorn_devices, ARRAY_SIZE(pronghorn_devices));
++
++	if (machine_is_pronghorn()) {
++		pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2);
++		pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(2);
++
++		pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3);
++		pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(3);
++
++		pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS2;
++		pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
++	} else {
++		pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(3);
++		pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(3);
++
++		pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(4);
++		pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(4);
++
++		pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
++		pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS4;
++
++		platform_device_register(&pronghorn_i2c_gpio);
++	}
++
++	platform_device_register(&pronghorn_pata);
++}
++
++MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= pronghorn_init,
++MACHINE_END
++
++MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= pronghorn_init,
++MACHINE_END
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -41,7 +41,8 @@ static __inline__ void __arch_decomp_set
+ 	 * Some boards are using UART2 as console
+ 	 */
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+-			 machine_is_gateway7001() || machine_is_wg302v2())
++			 machine_is_gateway7001() || machine_is_wg302v2() ||
++			 machine_is_pronghorn() || machine_is_pronghorn_metro())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
diff --git a/target/linux/ixp4xx/patches-2.6.37/111-pronghorn_swap_uarts.patch b/target/linux/ixp4xx/patches-2.6.37/111-pronghorn_swap_uarts.patch
new file mode 100644
index 0000000..b9fa507
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/111-pronghorn_swap_uarts.patch
@@ -0,0 +1,44 @@
+--- a/arch/arm/mach-ixp4xx/pronghorn-setup.c
++++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
+@@ -51,31 +51,31 @@ static struct platform_device pronghorn_
+ 
+ static struct resource pronghorn_uart_resources [] = {
+ 	{
+-		.start		= IXP4XX_UART1_BASE_PHYS,
+-		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.start		= IXP4XX_UART2_BASE_PHYS,
++		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ 		.flags		= IORESOURCE_MEM
+ 	},
+ 	{
+-		.start		= IXP4XX_UART2_BASE_PHYS,
+-		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.start		= IXP4XX_UART1_BASE_PHYS,
++		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ 		.flags		= IORESOURCE_MEM
+ 	}
+ };
+ 
+ static struct plat_serial8250_port pronghorn_uart_data[] = {
+ 	{
+-		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+-		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+-		.irq		= IRQ_IXP4XX_UART1,
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
+ 		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ 		.iotype		= UPIO_MEM,
+ 		.regshift	= 2,
+ 		.uartclk	= IXP4XX_UART_XTAL,
+ 	},
+ 	{
+-		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+-		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+-		.irq		= IRQ_IXP4XX_UART2,
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
+ 		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ 		.iotype		= UPIO_MEM,
+ 		.regshift	= 2,
diff --git a/target/linux/ixp4xx/patches-2.6.37/115-sidewinder_support.patch b/target/linux/ixp4xx/patches-2.6.37/115-sidewinder_support.patch
new file mode 100644
index 0000000..2ec3d95
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/115-sidewinder_support.patch
@@ -0,0 +1,282 @@
+From 60bdaaaf3446b4237566c6e04855186fc7bd766b Mon Sep 17 00:00:00 2001
+From: Imre Kaloz <kaloz@openwrt.org>
+Date: Sun, 13 Jul 2008 22:46:45 +0200
+Subject: [PATCH] Add support for the ADI Sidewinder
+
+Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
+---
+ arch/arm/mach-ixp4xx/Kconfig            |   10 ++-
+ arch/arm/mach-ixp4xx/Makefile           |    2 +
+ arch/arm/mach-ixp4xx/sidewinder-pci.c   |   68 ++++++++++++++
+ arch/arm/mach-ixp4xx/sidewinder-setup.c |  151 +++++++++++++++++++++++++++++++
+ 4 files changed, 230 insertions(+), 1 deletions(-)
+ create mode 100644 arch/arm/mach-ixp4xx/sidewinder-pci.c
+ create mode 100644 arch/arm/mach-ixp4xx/sidewinder-setup.c
+
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -81,6 +81,14 @@ config MACH_PRONGHORN
+ config MACH_PRONGHORNMETRO
+ 	def_bool MACH_PRONGHORN
+ 
++config MACH_SIDEWINDER
++	bool "ADI Sidewinder"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support the ADI 
++	  Engineering Sidewinder board. For more information on this
++	  platform, see http://www.adiengineering.com
++
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+@@ -177,7 +185,7 @@ config MACH_ARCOM_VULCAN
+ #
+ config CPU_IXP46X
+ 	bool
+-	depends on MACH_IXDP465
++	depends on MACH_IXDP465 || MACH_SIDEWINDER
+ 	default y
+ 
+ config CPU_IXP43X
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -19,6 +19,7 @@ obj-pci-$(CONFIG_MACH_WG302V2)		+= wg302
+ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ obj-pci-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-pci.o
+ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
++obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -37,6 +38,7 @@ obj-$(CONFIG_MACH_FSG)		+= fsg-setup.o
+ obj-$(CONFIG_MACH_GORAMO_MLR)	+= goramo_mlr.o
+ obj-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-setup.o
+ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
++obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/sidewinder-pci.c
+@@ -0,0 +1,68 @@
++/*
++ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c
++ *
++ * PCI setup routines for ADI Engineering Sidewinder
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++
++#include <asm/mach/pci.h>
++
++void __init sidewinder_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init sidewinder_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 1)
++		return IRQ_IXP4XX_GPIO11;
++	else if (slot == 2)
++		return IRQ_IXP4XX_GPIO10;
++	else if (slot == 3)
++		return IRQ_IXP4XX_GPIO9;
++	else
++		return -1;
++}
++
++struct hw_pci sidewinder_pci __initdata = {
++	.nr_controllers	= 1,
++	.preinit	= sidewinder_pci_preinit,
++	.swizzle	= pci_std_swizzle,
++	.setup		= ixp4xx_setup,
++	.scan		= ixp4xx_scan_bus,
++	.map_irq	= sidewinder_map_irq,
++};
++
++int __init sidewinder_pci_init(void)
++{
++	if (machine_is_sidewinder())
++		pci_common_init(&sidewinder_pci);
++	return 0;
++}
++
++subsys_initcall(sidewinder_pci_init);
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/sidewinder-setup.c
+@@ -0,0 +1,149 @@
++/*
++ * arch/arm/mach-ixp4xx/sidewinder-setup.c
++ *
++ * Board setup for the ADI Engineering Sidewinder
++ *
++ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
++ *
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <Kaloz@openwrt.org>
++ */
++
++#include <linux/kernel.h>
++#include <linux/serial.h>
++#include <linux/serial_8250.h>
++
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data sidewinder_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource sidewinder_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device sidewinder_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &sidewinder_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &sidewinder_flash_resource,
++};
++
++static struct resource sidewinder_uart_resources[] = {
++	{
++		.start	= IXP4XX_UART1_BASE_PHYS,
++		.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags	= IORESOURCE_MEM,
++	},
++	{
++		.start	= IXP4XX_UART2_BASE_PHYS,
++		.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags	= IORESOURCE_MEM,
++	}
++};
++
++static struct plat_serial8250_port sidewinder_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device sidewinder_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev		= {
++		.platform_data	= sidewinder_uart_data,
++	},
++	.num_resources	= ARRAY_SIZE(sidewinder_uart_resources),
++	.resource	= sidewinder_uart_resources,
++};
++
++static struct eth_plat_info sidewinder_plat_eth[] = {
++	{
++		.phy		= 5,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}, {
++		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
++		.phy_mask	= 0x1e,
++		.rxq		= 4,
++		.txreadyq	= 21,
++	}, {
++		.phy		= 31,
++		.rxq		= 2,
++		.txreadyq	= 19,
++	}
++};
++
++static struct platform_device sidewinder_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= sidewinder_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= sidewinder_plat_eth + 1,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEA,
++		.dev.platform_data	= sidewinder_plat_eth + 2,
++	}
++};
++
++static struct platform_device *sidewinder_devices[] __initdata = {
++	&sidewinder_flash,
++	&sidewinder_uart,
++	&sidewinder_eth[0],
++	&sidewinder_eth[1],
++	&sidewinder_eth[2],
++};
++
++static void __init sidewinder_init(void)
++{
++	ixp4xx_sys_init();
++
++	sidewinder_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	sidewinder_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_64M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++	platform_add_devices(sidewinder_devices, ARRAY_SIZE(sidewinder_devices));
++}
++
++MACHINE_START(SIDEWINDER, "ADI Engineering Sidewinder")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= sidewinder_init,
++MACHINE_END
diff --git a/target/linux/ixp4xx/patches-2.6.37/116-sidewinder_fis_location.patch b/target/linux/ixp4xx/patches-2.6.37/116-sidewinder_fis_location.patch
new file mode 100644
index 0000000..96be37f
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/116-sidewinder_fis_location.patch
@@ -0,0 +1,30 @@
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -31,6 +31,8 @@
+ 
+ #define BOARD_CONFIG_PART		"boardconfig"
+ 
++#include <asm/mach-types.h>
++
+ struct fis_image_desc {
+     unsigned char name[16];      // Null terminated name
+     uint32_t	  flash_base;    // Address within FLASH of image
+@@ -48,7 +50,8 @@ struct fis_list {
+ 	struct fis_list *next;
+ };
+ 
+-static int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK;
++int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK;
++
+ module_param(directory, int, 0);
+ 
+ static inline int redboot_checksum(struct fis_image_desc *img)
+@@ -77,6 +80,8 @@ static int parse_redboot_partitions(stru
+ #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
+ 	static char nullstring[] = "unallocated";
+ #endif
++	if (machine_is_sidewinder())
++		directory = -5;
+ 
+ 	if ( directory < 0 ) {
+ 		offset = master->size + directory * master->erasesize;
diff --git a/target/linux/ixp4xx/patches-2.6.37/120-compex_support.patch b/target/linux/ixp4xx/patches-2.6.37/120-compex_support.patch
new file mode 100644
index 0000000..c549314
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/120-compex_support.patch
@@ -0,0 +1,212 @@
+From 24025a2dcf1248079dd3019fac6ed955252d277f Mon Sep 17 00:00:00 2001
+From: Imre Kaloz <kaloz@openwrt.org>
+Date: Mon, 14 Jul 2008 21:56:34 +0200
+Subject: [PATCH] Add support for the Compex WP18 / NP18A boards
+
+Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
+---
+ arch/arm/mach-ixp4xx/Kconfig        |    8 ++
+ arch/arm/mach-ixp4xx/Makefile       |    2 +
+ arch/arm/mach-ixp4xx/compex-setup.c |  136 +++++++++++++++++++++++++++++++++++
+ arch/arm/mach-ixp4xx/ixdp425-pci.c  |    3 +-
+ arch/arm/tools/mach-types           |    2 +-
+ 5 files changed, 149 insertions(+), 2 deletions(-)
+ create mode 100644 arch/arm/mach-ixp4xx/compex-setup.c
+
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -89,6 +89,14 @@ config MACH_SIDEWINDER
+ 	  Engineering Sidewinder board. For more information on this
+ 	  platform, see http://www.adiengineering.com
+ 
++config MACH_COMPEX
++	bool "Compex WP18 / NP18A"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support Compex' 
++	  WP18 or NP18A boards. For more information on this
++	  platform, see http://www.compex.com.sg/home/OEM/product_ap.htm
++
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -20,6 +20,7 @@ obj-pci-$(CONFIG_MACH_FSG)		+= fsg-pci.o
+ obj-pci-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-pci.o
+ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
+ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
++obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -39,6 +40,7 @@ obj-$(CONFIG_MACH_GORAMO_MLR)	+= goramo_
+ obj-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulcan-setup.o
+ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
+ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
++obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/compex-setup.c
+@@ -0,0 +1,136 @@
++/*
++ * arch/arm/mach-ixp4xx/compex-setup.c
++ *
++ * Compex WP18 / NP18A board-setup
++ *
++ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
++ *
++ * based on coyote-setup.c:
++ *	Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <Kaloz@openwrt.org>
++ */
++
++#include <linux/kernel.h>
++#include <linux/serial.h>
++#include <linux/serial_8250.h>
++
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data compex_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource compex_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device compex_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &compex_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &compex_flash_resource,
++};
++
++static struct resource compex_uart_resources[] = {
++	{
++		.start		= IXP4XX_UART1_BASE_PHYS,
++		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	},
++	{
++		.start		= IXP4XX_UART2_BASE_PHYS,
++		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	}
++};
++
++static struct plat_serial8250_port compex_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device compex_uart = {
++	.name			= "serial8250",
++	.id			= PLAT8250_DEV_PLATFORM,
++	.dev.platform_data	= compex_uart_data,
++	.num_resources		= 2,
++	.resource		= compex_uart_resources,
++};
++
++static struct eth_plat_info compex_plat_eth[] = {
++	{
++		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
++		.phy_mask	= 0xf0000,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}, {
++		.phy		= 3,
++		.rxq		= 4,
++		.txreadyq	= 21,
++	}
++};
++
++static struct platform_device compex_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= compex_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= compex_plat_eth + 1,
++	}
++};
++
++static struct platform_device *compex_devices[] __initdata = {
++	&compex_flash,
++	&compex_uart,
++	&compex_eth[0],
++	&compex_eth[1],
++};
++
++static void __init compex_init(void)
++{
++	ixp4xx_sys_init();
++
++	compex_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	compex_flash_resource.end =
++		IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
++
++	platform_add_devices(compex_devices, ARRAY_SIZE(compex_devices));
++}
++
++MACHINE_START(COMPEX, "Compex WP18 / NP18A")
++	/* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= compex_init,
++MACHINE_END
+--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c
++++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c
+@@ -70,7 +70,8 @@ struct hw_pci ixdp425_pci __initdata = {
+ int __init ixdp425_pci_init(void)
+ {
+ 	if (machine_is_ixdp425() || machine_is_ixcdp1100() ||
+-			machine_is_ixdp465() || machine_is_kixrp435())
++			machine_is_ixdp465() || machine_is_kixrp435() ||
++			machine_is_compex())
+ 		pci_common_init(&ixdp425_pci);
+ 	return 0;
+ }
+--- a/arch/arm/tools/mach-types
++++ b/arch/arm/tools/mach-types
+@@ -1273,7 +1273,7 @@ oiab			MACH_OIAB		OIAB			1269
+ smdk6400		MACH_SMDK6400		SMDK6400		1270
+ nokia_n800		MACH_NOKIA_N800		NOKIA_N800		1271
+ greenphone		MACH_GREENPHONE		GREENPHONE		1272
+-compex42x		MACH_COMPEXWP18		COMPEXWP18		1273
++compex			MACH_COMPEX		COMPEX			1273
+ xmate			MACH_XMATE		XMATE			1274
+ energizer		MACH_ENERGIZER		ENERGIZER		1275
+ ime1			MACH_IME1		IME1			1276
diff --git a/target/linux/ixp4xx/patches-2.6.37/130-wrt300nv2_support.patch b/target/linux/ixp4xx/patches-2.6.37/130-wrt300nv2_support.patch
new file mode 100644
index 0000000..865bb9d
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/130-wrt300nv2_support.patch
@@ -0,0 +1,225 @@
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -97,6 +97,14 @@ config MACH_COMPEX
+ 	  WP18 or NP18A boards. For more information on this
+ 	  platform, see http://www.compex.com.sg/home/OEM/product_ap.htm
+ 
++config MACH_WRT300NV2
++	bool "Linksys WRT300N v2"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support Linksys' 
++	  WRT300N v2 router. For more information on this
++	  platform, see http://openwrt.org
++
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -21,6 +21,7 @@ obj-pci-$(CONFIG_MACH_ARCOM_VULCAN)	+= v
+ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-pci.o
+ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
+ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
++obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -41,6 +42,7 @@ obj-$(CONFIG_MACH_ARCOM_VULCAN)	+= vulca
+ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghorn-setup.o
+ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
+ obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
++obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/wrt300nv2-pci.c
+@@ -0,0 +1,65 @@
++/*
++ * arch/arch/mach-ixp4xx/wrt300nv2-pci.c
++ *
++ * PCI setup routines for Linksys WRT300N v2
++ *
++ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++
++#include <asm/mach/pci.h>
++
++extern void ixp4xx_pci_preinit(void);
++extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
++extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
++
++void __init wrt300nv2_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init wrt300nv2_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 1)
++		return IRQ_IXP4XX_GPIO8;
++	else return -1;
++}
++
++struct hw_pci wrt300nv2_pci __initdata = {
++	.nr_controllers = 1,
++	.preinit =        wrt300nv2_pci_preinit,
++	.swizzle =        pci_std_swizzle,
++	.setup =          ixp4xx_setup,
++	.scan =           ixp4xx_scan_bus,
++	.map_irq =        wrt300nv2_map_irq,
++};
++
++int __init wrt300nv2_pci_init(void)
++{
++	if (machine_is_wrt300nv2())
++		pci_common_init(&wrt300nv2_pci);
++	return 0;
++}
++
++subsys_initcall(wrt300nv2_pci_init);
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+@@ -0,0 +1,108 @@
++/*
++ * arch/arm/mach-ixp4xx/wrt300nv2-setup.c
++ *
++ * Board setup for the Linksys WRT300N v2
++ *
++ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
++ *
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <Kaloz@openwrt.org>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++
++#include <asm/types.h>
++#include <asm/setup.h>
++#include <asm/memory.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data wrt300nv2_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource wrt300nv2_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device wrt300nv2_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &wrt300nv2_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &wrt300nv2_flash_resource,
++};
++
++static struct resource wrt300nv2_uart_resource = {
++	.start	= IXP4XX_UART2_BASE_PHYS,
++	.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++	.flags	= IORESOURCE_MEM,
++};
++
++static struct plat_serial8250_port wrt300nv2_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device wrt300nv2_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev			= {
++		.platform_data	= wrt300nv2_uart_data,
++	},
++	.num_resources	= 1,
++	.resource	= &wrt300nv2_uart_resource,
++};
++
++static struct platform_device *wrt300nv2_devices[] __initdata = {
++	&wrt300nv2_flash,
++	&wrt300nv2_uart
++};
++
++static void __init wrt300nv2_init(void)
++{
++	ixp4xx_sys_init();
++
++	wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	wrt300nv2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++	platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices));
++}
++
++#ifdef CONFIG_MACH_WRT300NV2
++MACHINE_START(WRT300NV2, "Linksys WRT300N v2")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= wrt300nv2_init,
++MACHINE_END
++#endif
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -42,7 +42,7 @@ static __inline__ void __arch_decomp_set
+ 	 */
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+ 			 machine_is_gateway7001() || machine_is_wg302v2() ||
+-			 machine_is_pronghorn() || machine_is_pronghorn_metro())
++			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
diff --git a/target/linux/ixp4xx/patches-2.6.37/131-wrt300nv2_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.37/131-wrt300nv2_mac_plat_info.patch
new file mode 100644
index 0000000..3ab68c4
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/131-wrt300nv2_mac_plat_info.patch
@@ -0,0 +1,40 @@
+--- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
++++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+@@ -76,9 +76,36 @@ static struct platform_device wrt300nv2_
+ 	.resource	= &wrt300nv2_uart_resource,
+ };
+ 
++/* Built-in 10/100 Ethernet MAC interfaces */
++static struct eth_plat_info wrt300nv2_plat_eth[] = {
++	{
++		.phy		= -1,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}, {
++		.phy		= 1,
++		.rxq		= 4,
++		.txreadyq	= 21,
++	}
++};
++
++static struct platform_device wrt300nv2_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= wrt300nv2_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= wrt300nv2_plat_eth + 1,
++	}
++};
++
+ static struct platform_device *wrt300nv2_devices[] __initdata = {
+ 	&wrt300nv2_flash,
+-	&wrt300nv2_uart
++	&wrt300nv2_uart,
++	&wrt300nv2_eth[0],
++	&wrt300nv2_eth[1],
+ };
+ 
+ static void __init wrt300nv2_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.37/132-wrt300nv2_mac_fix.patch b/target/linux/ixp4xx/patches-2.6.37/132-wrt300nv2_mac_fix.patch
new file mode 100644
index 0000000..381cc5b
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/132-wrt300nv2_mac_fix.patch
@@ -0,0 +1,72 @@
+--- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
++++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+@@ -3,6 +3,7 @@
+  *
+  * Board setup for the Linksys WRT300N v2
+  *
++ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com>
+  * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+  *
+  * based on coyote-setup.c:
+@@ -18,6 +19,7 @@
+ #include <linux/tty.h>
+ #include <linux/serial_8250.h>
+ #include <linux/slab.h>
++#include <linux/etherdevice.h>
+ 
+ #include <asm/types.h>
+ #include <asm/setup.h>
+@@ -79,7 +81,8 @@ static struct platform_device wrt300nv2_
+ /* Built-in 10/100 Ethernet MAC interfaces */
+ static struct eth_plat_info wrt300nv2_plat_eth[] = {
+ 	{
+-		.phy		= -1,
++		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
++		.phy_mask	= 0x0F0000,
+ 		.rxq		= 3,
+ 		.txreadyq	= 20,
+ 	}, {
+@@ -110,6 +113,10 @@ static struct platform_device *wrt300nv2
+ 
+ static void __init wrt300nv2_init(void)
+ {
++	uint8_t __iomem *f;
++	int offset = 0;
++	int i;
++
+ 	ixp4xx_sys_init();
+ 
+ 	wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+@@ -119,6 +126,32 @@ static void __init wrt300nv2_init(void)
+ 	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+ 
+ 	platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices));
++
++	f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x60000);
++
++	if (f) {
++		for (i = 0; i < 6; i++) {
++#ifdef __ARMEB__
++			wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + i);
++			if (i == 5)
++				offset = 1;
++			wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset);
++#else
++			wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + (i^3));
++			if (i == 5)
++				offset = 1;
++			wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset);
++#endif
++		}
++		iounmap(f);
++	}
++
++	if (!(is_valid_ether_addr(wrt300nv2_plat_eth[0].hwaddr)))
++		random_ether_addr(wrt300nv2_plat_eth[0].hwaddr);
++	if (!(is_valid_ether_addr(wrt300nv2_plat_eth[1].hwaddr))) {
++		memcpy(wrt300nv2_plat_eth[1].hwaddr, wrt300nv2_plat_eth[0].hwaddr, ETH_ALEN);
++		wrt300nv2_plat_eth[1].hwaddr[5] = (wrt300nv2_plat_eth[0].hwaddr[5] + 1);
++	}
+ }
+ 
+ #ifdef CONFIG_MACH_WRT300NV2
diff --git a/target/linux/ixp4xx/patches-2.6.37/150-lanready_ap1000_support.patch b/target/linux/ixp4xx/patches-2.6.37/150-lanready_ap1000_support.patch
new file mode 100644
index 0000000..16f19ba
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/150-lanready_ap1000_support.patch
@@ -0,0 +1,200 @@
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/ap1000-setup.c
+@@ -0,0 +1,151 @@
++/*
++ * arch/arm/mach-ixp4xx/ap1000-setup.c
++ *
++ * Lanready AP-1000
++ *
++ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
++ *
++ * based on ixdp425-setup.c:
++ *	Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <Kaloz@openwrt.org>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++
++#include <asm/types.h>
++#include <asm/setup.h>
++#include <asm/memory.h>
++#include <mach/hardware.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data ap1000_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource ap1000_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device ap1000_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &ap1000_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &ap1000_flash_resource,
++};
++
++static struct resource ap1000_uart_resources[] = {
++	{
++		.start		= IXP4XX_UART1_BASE_PHYS,
++		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	},
++	{
++		.start		= IXP4XX_UART2_BASE_PHYS,
++		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	}
++};
++
++static struct plat_serial8250_port ap1000_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device ap1000_uart = {
++	.name			= "serial8250",
++	.id			= PLAT8250_DEV_PLATFORM,
++	.dev.platform_data	= ap1000_uart_data,
++	.num_resources		= 2,
++	.resource		= ap1000_uart_resources
++};
++
++static struct platform_device *ap1000_devices[] __initdata = {
++	&ap1000_flash,
++	&ap1000_uart
++};
++
++static char ap1000_mem_fixup[] __initdata = "mem=64M ";
++
++static void __init ap1000_fixup(struct machine_desc *desc,
++		struct tag *tags, char **cmdline, struct meminfo *mi)
++
++{
++	struct tag *t = tags;
++	char *p = *cmdline;
++
++	/* Find the end of the tags table, taking note of any cmdline tag. */
++	for (; t->hdr.size; t = tag_next(t)) {
++		if (t->hdr.tag == ATAG_CMDLINE) {
++			p = t->u.cmdline.cmdline;
++		}
++	}
++
++	/* Overwrite the end of the table with a new cmdline tag. */
++	t->hdr.tag = ATAG_CMDLINE;
++	t->hdr.size = (sizeof (struct tag_header) +
++		strlen(ap1000_mem_fixup) + strlen(p) + 1 + 4) >> 2;
++	strlcpy(t->u.cmdline.cmdline, ap1000_mem_fixup, COMMAND_LINE_SIZE);
++	strlcpy(t->u.cmdline.cmdline + strlen(ap1000_mem_fixup), p,
++		COMMAND_LINE_SIZE - strlen(ap1000_mem_fixup));
++
++	/* Terminate the table. */
++	t = tag_next(t);
++	t->hdr.tag = ATAG_NONE;
++	t->hdr.size = 0;
++}
++
++static void __init ap1000_init(void)
++{
++	ixp4xx_sys_init();
++
++	ap1000_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	ap1000_flash_resource.end =
++		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
++
++	platform_add_devices(ap1000_devices, ARRAY_SIZE(ap1000_devices));
++}
++
++#ifdef CONFIG_MACH_AP1000
++MACHINE_START(AP1000, "Lanready AP-1000")
++	/* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.fixup		= ap1000_fixup,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= ap1000_init,
++MACHINE_END
++#endif
+--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c
++++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c
+@@ -71,7 +71,7 @@ int __init ixdp425_pci_init(void)
+ {
+ 	if (machine_is_ixdp425() || machine_is_ixcdp1100() ||
+ 			machine_is_ixdp465() || machine_is_kixrp435() ||
+-			machine_is_compex())
++			machine_is_compex() || machine_is_ap1000())
+ 		pci_common_init(&ixdp425_pci);
+ 	return 0;
+ }
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -105,6 +105,14 @@ config MACH_WRT300NV2
+ 	  WRT300N v2 router. For more information on this
+ 	  platform, see http://openwrt.org
+ 
++config MACH_AP1000
++	bool "Lanready AP-1000"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support Lanready's
++	  AP1000 board. For more information on this
++	  platform, see http://openwrt.org
++
+ config ARCH_IXDP425
+ 	bool "IXDP425"
+ 	help
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -22,6 +22,7 @@ obj-pci-$(CONFIG_MACH_PRONGHORN)	+= pron
+ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-pci.o
+ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
++obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -43,6 +44,7 @@ obj-$(CONFIG_MACH_PRONGHORN)	+= pronghor
+ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewinder-setup.o
+ obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
++obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
diff --git a/target/linux/ixp4xx/patches-2.6.37/151-lanready_ap1000_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.37/151-lanready_ap1000_mac_plat_info.patch
new file mode 100644
index 0000000..a1214d5
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/151-lanready_ap1000_mac_plat_info.patch
@@ -0,0 +1,41 @@
+--- a/arch/arm/mach-ixp4xx/ap1000-setup.c
++++ b/arch/arm/mach-ixp4xx/ap1000-setup.c
+@@ -90,9 +90,37 @@ static struct platform_device ap1000_uar
+ 	.resource		= ap1000_uart_resources
+ };
+ 
++/* Built-in 10/100 Ethernet MAC interfaces */
++static struct eth_plat_info ap1000_plat_eth[] = {
++	{
++		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
++		.phy_mask	= 0x1e,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}, {
++		.phy		= 5,
++		.rxq		= 4,
++		.txreadyq	= 21,
++	}
++};
++
++static struct platform_device ap1000_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= ap1000_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= ap1000_plat_eth + 1,
++	}
++};
++
+ static struct platform_device *ap1000_devices[] __initdata = {
+ 	&ap1000_flash,
+-	&ap1000_uart
++	&ap1000_uart,
++	&ap1000_eth[0],
++	&ap1000_eth[1],
+ };
+ 
+ static char ap1000_mem_fixup[] __initdata = "mem=64M ";
diff --git a/target/linux/ixp4xx/patches-2.6.37/162-wg302v1_mem_fixup.patch b/target/linux/ixp4xx/patches-2.6.37/162-wg302v1_mem_fixup.patch
new file mode 100644
index 0000000..684db44
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/162-wg302v1_mem_fixup.patch
@@ -0,0 +1,47 @@
+--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
++++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
+@@ -115,6 +115,36 @@ static struct platform_device *wg302v1_d
+ 	&wg302v1_eth[0],
+ };
+ 
++static char wg302v1_mem_fixup[] __initdata = "mem=32M ";
++
++static void __init wg302v1_fixup(struct machine_desc *desc,
++		struct tag *tags, char **cmdline, struct meminfo *mi)
++
++{
++	struct tag *t = tags;
++	char *p = *cmdline;
++
++	/* Find the end of the tags table, taking note of any cmdline tag. */
++	for (; t->hdr.size; t = tag_next(t)) {
++		if (t->hdr.tag == ATAG_CMDLINE) {
++			p = t->u.cmdline.cmdline;
++		}
++	}
++
++	/* Overwrite the end of the table with a new cmdline tag. */
++	t->hdr.tag = ATAG_CMDLINE;
++	t->hdr.size = (sizeof (struct tag_header) +
++		strlen(wg302v1_mem_fixup) + strlen(p) + 1 + 4) >> 2;
++	strlcpy(t->u.cmdline.cmdline, wg302v1_mem_fixup, COMMAND_LINE_SIZE);
++	strlcpy(t->u.cmdline.cmdline + strlen(wg302v1_mem_fixup), p,
++		COMMAND_LINE_SIZE - strlen(wg302v1_mem_fixup));
++
++	/* Terminate the table. */
++	t = tag_next(t);
++	t->hdr.tag = ATAG_NONE;
++	t->hdr.size = 0;
++}
++
+ static void __init wg302v1_init(void)
+ {
+ 	ixp4xx_sys_init();
+@@ -133,6 +163,7 @@ MACHINE_START(WG302V1, "Netgear WG302 v1
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ 	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+ 	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.fixup		= wg302v1_fixup,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
diff --git a/target/linux/ixp4xx/patches-2.6.37/170-ixdpg425_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.37/170-ixdpg425_mac_plat_info.patch
new file mode 100644
index 0000000..5333532
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/170-ixdpg425_mac_plat_info.patch
@@ -0,0 +1,41 @@
+--- a/arch/arm/mach-ixp4xx/coyote-setup.c
++++ b/arch/arm/mach-ixp4xx/coyote-setup.c
+@@ -81,9 +81,37 @@ static struct platform_device coyote_uar
+ 	.resource	= &coyote_uart_resource,
+ };
+ 
++/* Built-in 10/100 Ethernet MAC interfaces */
++static struct eth_plat_info ixdpg425_plat_eth[] = {
++        {
++                .phy            = 5,
++                .rxq            = 3,
++                .txreadyq       = 20,
++        }, {
++                .phy            = 4,
++                .rxq            = 4,
++                .txreadyq       = 21,
++        }
++};
++
++static struct platform_device ixdpg425_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= ixdpg425_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= ixdpg425_plat_eth + 1,
++	}
++};
++
++
+ static struct platform_device *coyote_devices[] __initdata = {
+ 	&coyote_flash,
+-	&coyote_uart
++	&coyote_uart,
++	&ixdpg425_eth[0],
++	&ixdpg425_eth[1],
+ };
+ 
+ static void __init coyote_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.37/180-tw5334_support.patch b/target/linux/ixp4xx/patches-2.6.37/180-tw5334_support.patch
new file mode 100644
index 0000000..e92d461
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/180-tw5334_support.patch
@@ -0,0 +1,285 @@
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -164,6 +164,14 @@ config ARCH_PRPMC1100
+ 	  PrPCM1100 Processor Mezanine Module. For more information on
+ 	  this platform, see <file:Documentation/arm/IXP4xx>.
+ 
++config MACH_TW5334
++	bool "Titan Wireless TW-533-4"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support the Titan
++	  Wireless TW533-4. For more information on this platform,
++	  see http://openwrt.org
++
+ config MACH_NAS100D
+ 	bool
+ 	prompt "NAS100D"
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -23,6 +23,7 @@ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sid
+ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+ obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
++obj-pci-$(CONFIG_MACH_TW5334)		+= tw5334-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -45,6 +46,7 @@ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewin
+ obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+ obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
++obj-$(CONFIG_MACH_TW5334)	+= tw5334-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/tw5334-setup.c
+@@ -0,0 +1,163 @@
++/*
++ * arch/arm/mach-ixp4xx/tw5334-setup.c
++ *
++ * Board setup for the Titan Wireless TW-533-4
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <Kaloz@openwrt.org>
++ */
++
++#include <linux/if_ether.h>
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++
++#include <asm/types.h>
++#include <asm/setup.h>
++#include <asm/memory.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data tw5334_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource tw5334_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device tw5334_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &tw5334_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &tw5334_flash_resource,
++};
++
++static struct resource tw5334_uart_resource = {
++	.start	= IXP4XX_UART2_BASE_PHYS,
++	.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++	.flags	= IORESOURCE_MEM,
++};
++
++static struct plat_serial8250_port tw5334_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device tw5334_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev			= {
++		.platform_data	= tw5334_uart_data,
++	},
++	.num_resources	= 1,
++	.resource	= &tw5334_uart_resource,
++};
++
++/* Built-in 10/100 Ethernet MAC interfaces */
++static struct eth_plat_info tw5334_plat_eth[] = {
++        {
++                .phy            = 0,
++                .rxq            = 3,
++		.txreadyq	= 20,
++        }, {
++                .phy            = 1,
++                .rxq            = 4,
++		.txreadyq	= 21,
++	}
++};
++
++static struct platform_device tw5334_eth[] = {
++        {
++                .name                   = "ixp4xx_eth",
++                .id                     = IXP4XX_ETH_NPEB,
++                .dev.platform_data      = tw5334_plat_eth,
++        }, {
++                .name                   = "ixp4xx_eth",
++                .id                     = IXP4XX_ETH_NPEC,
++                .dev.platform_data      = tw5334_plat_eth + 1,
++	}
++};
++
++static struct platform_device *tw5334_devices[] __initdata = {
++	&tw5334_flash,
++	&tw5334_uart,
++	&tw5334_eth[0],
++	&tw5334_eth[1],
++};
++
++static void __init tw5334_init(void)
++{
++	uint8_t __iomem *f;
++	int i;
++
++	ixp4xx_sys_init();
++
++	tw5334_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	tw5334_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++	platform_add_devices(tw5334_devices, ARRAY_SIZE(tw5334_devices));
++
++	/*
++	 * Map in a portion of the flash and read the MAC addresses.
++	 * Since it is stored in BE in the flash itself, we need to
++	 * byteswap it if we're in LE mode.
++	 */
++	f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x1000000);
++	if (f) {
++		for (i = 0; i < 6; i++) {
++#ifdef __ARMEB__
++			tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + i);
++			tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + i);
++#else
++			tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + (i^3));
++			tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + (i^3));
++#endif
++		}
++		iounmap(f);
++	}
++
++	printk(KERN_INFO "TW-533-4: Using MAC address %pM for port 0\n",
++		tw5334_plat_eth[0].hwaddr);
++	printk(KERN_INFO "TW-533-4: Using MAC address %pM for port 1\n",
++		tw5334_plat_eth[1].hwaddr);
++}
++
++#ifdef CONFIG_MACH_TW5334
++MACHINE_START(TW5334, "Titan Wireless TW-533-4")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= tw5334_init,
++MACHINE_END
++#endif
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/tw5334-pci.c
+@@ -0,0 +1,69 @@
++/*
++ * arch/arch/mach-ixp4xx/tw5334-pci.c
++ *
++ * PCI setup routines for the Titan Wireless TW-533-4
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++
++#include <asm/mach/pci.h>
++
++void __init tw5334_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO2, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO0, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init tw5334_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 12)
++		return IRQ_IXP4XX_GPIO6;
++	else if (slot == 13)
++		return IRQ_IXP4XX_GPIO2;
++	else if (slot == 14)
++		return IRQ_IXP4XX_GPIO1;
++	else if (slot == 15)
++		return IRQ_IXP4XX_GPIO0;
++	else return -1;
++}
++
++struct hw_pci tw5334_pci __initdata = {
++	.nr_controllers = 1,
++	.preinit =        tw5334_pci_preinit,
++	.swizzle =        pci_std_swizzle,
++	.setup =          ixp4xx_setup,
++	.scan =           ixp4xx_scan_bus,
++	.map_irq =        tw5334_map_irq,
++};
++
++int __init tw5334_pci_init(void)
++{
++	if (machine_is_tw5334())
++		pci_common_init(&tw5334_pci);
++	return 0;
++}
++
++subsys_initcall(tw5334_pci_init);
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -42,7 +42,8 @@ static __inline__ void __arch_decomp_set
+ 	 */
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+ 			 machine_is_gateway7001() || machine_is_wg302v2() ||
+-			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2())
++			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
++			 machine_is_tw5334())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
diff --git a/target/linux/ixp4xx/patches-2.6.37/185-mi424wr_support.patch b/target/linux/ixp4xx/patches-2.6.37/185-mi424wr_support.patch
new file mode 100644
index 0000000..d85d3d1
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/185-mi424wr_support.patch
@@ -0,0 +1,465 @@
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/mi424wr-pci.c
+@@ -0,0 +1,71 @@
++/*
++ * arch/arm/mach-ixp4xx/mi424wr-pci.c
++ *
++ * Actiontec MI424WR board-level PCI initialization
++ *
++ * Copyright (C) 2008 Jose Vasconcellos
++ *
++ * Maintainer: Jose Vasconcellos <jvasco@verizon.net>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <asm/mach/pci.h>
++
++/* PCI controller GPIO to IRQ pin mappings
++ * This information was obtained from Actiontec's GPL release.
++ *
++ *		INTA		INTB
++ * SLOT 13	8		6
++ * SLOT 14	7		8
++ * SLOT 15	6		7
++ */
++
++void __init mi424wr_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init mi424wr_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 13)
++		return IRQ_IXP4XX_GPIO8;
++	if (slot == 14)
++		return IRQ_IXP4XX_GPIO7;
++	if (slot == 15)
++		return IRQ_IXP4XX_GPIO6;
++
++	return -1;
++}
++
++struct hw_pci mi424wr_pci __initdata = {
++	.nr_controllers = 1,
++	.preinit	= mi424wr_pci_preinit,
++	.swizzle	= pci_std_swizzle,
++	.setup		= ixp4xx_setup,
++	.scan		= ixp4xx_scan_bus,
++	.map_irq	= mi424wr_map_irq,
++};
++
++int __init mi424wr_pci_init(void)
++{
++	if (machine_is_mi424wr())
++		pci_common_init(&mi424wr_pci);
++	return 0;
++}
++
++subsys_initcall(mi424wr_pci_init);
++
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/mi424wr-setup.c
+@@ -0,0 +1,344 @@
++/*
++ * arch/arm/mach-ixp4xx/mi424wr-setup.c
++ *
++ * Actiontec MI424-WR board setup
++ * Copyright (c) 2008 Jose Vasconcellos
++ *
++ * Based on Gemtek GTWX5715 by
++ * Copyright (C) 2004 George T. Joseph
++ * Derived from Coyote
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version 2
++ * of the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.
++ *
++ */
++
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/serial_8250.h>
++#include <linux/types.h>
++#include <linux/memory.h>
++#include <linux/leds.h>
++#include <linux/spi/spi_gpio_old.h>
++
++#include <asm/setup.h>
++#include <asm/irq.h>
++#include <asm/io.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++/*
++ * GPIO 2,3,4 and 9 are hard wired to the Micrel/Kendin KS8995M Switch
++ * and operate as an SPI type interface.  The details of the interface
++ * are available on Kendin/Micrel's web site.
++ */
++
++#define MI424WR_KSSPI_SELECT		9
++#define MI424WR_KSSPI_TXD		4
++#define MI424WR_KSSPI_CLOCK		2
++#define MI424WR_KSSPI_RXD		3
++
++/*
++ * The "reset" button is wired to GPIO 10.
++ * The GPIO is brought "low" when the button is pushed.
++ */
++
++#define MI424WR_BUTTON_GPIO	10
++#define MI424WR_BUTTON_IRQ	IRQ_IXP4XX_GPIO10
++
++#define MI424WR_MOCA_WAN_LED	11
++
++/* Latch on CS1 - taken from Actiontec's 2.4 source code
++ * 
++ * default latch value
++ * 0  - power alarm led (red)           0 (off)
++ * 1  - power led (green)               0 (off)
++ * 2  - wireless led    (green)         1 (off)
++ * 3  - no internet led (red)           0 (off)
++ * 4  - internet ok led (green)         0 (off)
++ * 5  - moca LAN                        0 (off)
++ * 6  - WAN alarm led (red)		0 (off)
++ * 7  - PCI reset                       1 (not reset)
++ * 8  - IP phone 1 led (green)          1 (off)
++ * 9  - IP phone 2 led (green)          1 (off)
++ * 10 - VOIP ready led (green)          1 (off)
++ * 11 - PSTN relay 1 control            0 (PSTN)
++ * 12 - PSTN relay 1 control            0 (PSTN)
++ * 13 - N/A
++ * 14 - N/A
++ * 15 - N/A
++ */
++
++#define MI424WR_LATCH_MASK              0x04
++#define MI424WR_LATCH_DEFAULT           0x1f86
++
++#define MI424WR_LATCH_ALARM_LED         0x00
++#define MI424WR_LATCH_POWER_LED         0x01
++#define MI424WR_LATCH_WIRELESS_LED      0x02
++#define MI424WR_LATCH_INET_DOWN_LED     0x03
++#define MI424WR_LATCH_INET_OK_LED       0x04
++#define MI424WR_LATCH_MOCA_LAN_LED      0x05
++#define MI424WR_LATCH_WAN_ALARM_LED     0x06
++#define MI424WR_LATCH_PCI_RESET         0x07
++#define MI424WR_LATCH_PHONE1_LED        0x08
++#define MI424WR_LATCH_PHONE2_LED        0x09
++#define MI424WR_LATCH_VOIP_LED          0x10
++#define MI424WR_LATCH_PSTN_RELAY1       0x11
++#define MI424WR_LATCH_PSTN_RELAY2       0x12
++
++/* initialize CS1 to default timings, Intel style, 16-bit bus */
++#define MI424WR_CS1_CONFIG	0x80000002
++
++/* Define both UARTs but they are not easily accessible.
++ */
++
++static struct resource mi424wr_uart_resources[] = {
++	{
++		.start	= IXP4XX_UART1_BASE_PHYS,
++		.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags	= IORESOURCE_MEM,
++	},
++	{
++		.start	= IXP4XX_UART2_BASE_PHYS,
++		.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags	= IORESOURCE_MEM,
++	}
++};
++
++
++static struct plat_serial8250_port mi424wr_uart_platform_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device mi424wr_uart_device = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev.platform_data	= mi424wr_uart_platform_data,
++	.num_resources	= ARRAY_SIZE(mi424wr_uart_resources),
++	.resource	= mi424wr_uart_resources,
++};
++
++static struct flash_platform_data mi424wr_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource mi424wr_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device mi424wr_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev.platform_data = &mi424wr_flash_data,
++	.num_resources	= 1,
++	.resource	= &mi424wr_flash_resource,
++};
++
++static int mi424wr_spi_boardinfo_setup(struct spi_board_info *bi,
++		struct spi_master *master, void *data)
++{
++
++	strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias));
++
++	bi->max_speed_hz = 5000000 /* Hz */;
++	bi->bus_num = master->bus_num;
++	bi->mode = SPI_MODE_0;
++
++	return 0;
++}
++
++static struct spi_gpio_platform_data mi424wr_spi_bus_data = {
++	.pin_cs			= MI424WR_KSSPI_SELECT,
++	.pin_clk		= MI424WR_KSSPI_CLOCK,
++	.pin_miso		= MI424WR_KSSPI_RXD,
++	.pin_mosi		= MI424WR_KSSPI_TXD,
++	.cs_activelow		= 1,
++	.no_spi_delay		= 1,
++	.boardinfo_setup	= mi424wr_spi_boardinfo_setup,
++};
++
++static struct gpio_led mi424wr_gpio_led[] = {
++	{
++		.name		= "moca-wan",	/* green led */
++		.gpio		= MI424WR_MOCA_WAN_LED,
++		.active_low	= 0,
++	}
++};
++
++static struct gpio_led_platform_data mi424wr_gpio_leds_data = {
++	.num_leds	= 1,
++	.leds		= mi424wr_gpio_led,
++};
++
++static struct platform_device mi424wr_gpio_leds = {
++	.name		= "leds-gpio",
++	.id		= -1,
++	.dev.platform_data = &mi424wr_gpio_leds_data,
++};
++
++static uint16_t latch_value = MI424WR_LATCH_DEFAULT;
++static uint16_t __iomem *iobase;
++
++static void mi424wr_latch_set_led(u8 bit, enum led_brightness value)
++{
++
++	if (((MI424WR_LATCH_MASK >> bit) & 1) ^ (value == LED_OFF))
++		latch_value &= ~(0x1 << bit);
++	else
++		latch_value |= (0x1 << bit);
++
++	__raw_writew(latch_value, iobase);
++
++}
++
++static struct latch_led mi424wr_latch_led[] = {
++	{
++		.name	= "power-alarm",
++		.bit	= MI424WR_LATCH_ALARM_LED,
++	},
++	{
++		.name	= "power-ok",
++		.bit	= MI424WR_LATCH_POWER_LED,
++	},
++	{
++		.name	= "wireless",	/* green led */
++		.bit	= MI424WR_LATCH_WIRELESS_LED,
++	},
++	{
++		.name	= "inet-down",	/* red led */
++		.bit	= MI424WR_LATCH_INET_DOWN_LED,
++	},
++	{
++		.name	= "inet-up",	/* green led */
++		.bit	= MI424WR_LATCH_INET_OK_LED,
++	},
++	{
++		.name	= "moca-lan",	/* green led */
++		.bit	= MI424WR_LATCH_MOCA_LAN_LED,
++	},
++	{
++		.name	= "wan-alarm",	/* red led */
++		.bit	= MI424WR_LATCH_WAN_ALARM_LED,
++	}
++};
++
++static struct latch_led_platform_data mi424wr_latch_leds_data = {
++	.num_leds	= ARRAY_SIZE(mi424wr_latch_led),
++	.mem		= 0x51000000,
++	.leds		= mi424wr_latch_led,
++	.set_led        = mi424wr_latch_set_led,
++};
++
++static struct platform_device mi424wr_latch_leds = {
++	.name		= "leds-latch",
++	.id		= -1,
++	.dev.platform_data = &mi424wr_latch_leds_data,
++};
++
++static struct platform_device mi424wr_spi_bus = {
++	.name		= "spi-gpio",
++	.id		= 0,
++	.dev.platform_data = &mi424wr_spi_bus_data,
++};
++
++static struct eth_plat_info mi424wr_npeb_data = {
++	.phy		= 17,	/* KS8721 */
++	.rxq		= 3,
++	.txreadyq	= 20,
++};
++
++static struct eth_plat_info mi424wr_npec_data = {
++	.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
++	.phy_mask	= 0x1e, /* ports 1-4 of the KS8995 switch */
++	.rxq		= 4,
++	.txreadyq	= 21,
++};
++
++static struct platform_device mi424wr_npe_devices[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= &mi424wr_npec_data,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= &mi424wr_npeb_data,
++	}
++};
++
++static struct platform_device *mi424wr_devices[] __initdata = {
++	&mi424wr_uart_device,
++	&mi424wr_flash,
++	&mi424wr_gpio_leds,
++	&mi424wr_latch_leds,
++	&mi424wr_spi_bus,
++	&mi424wr_npe_devices[0],
++	&mi424wr_npe_devices[1],
++};
++
++static void __init mi424wr_init(void)
++{
++	ixp4xx_sys_init();
++
++	mi424wr_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	mi424wr_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_8M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = MI424WR_CS1_CONFIG;
++
++	/* configure button as input
++	 */
++	gpio_line_config(MI424WR_BUTTON_GPIO, IXP4XX_GPIO_IN);
++
++	/* Initialize LEDs and enables PCI bus.
++	 */
++	iobase = ioremap_nocache(IXP4XX_EXP_BUS_BASE(1), 0x1000);
++	__raw_writew(latch_value, iobase);
++
++	platform_add_devices(mi424wr_devices, ARRAY_SIZE(mi424wr_devices));
++}
++
++
++MACHINE_START(MI424WR, "Actiontec MI424WR")
++	/* Maintainer: Jose Vasconcellos */
++	.phys_io	= IXP4XX_UART2_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_UART2_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= mi424wr_init,
++MACHINE_END
++
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -24,6 +24,7 @@ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp42
+ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+ obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_TW5334)		+= tw5334-pci.o
++obj-pci-$(CONFIG_MACH_MI424WR)		+= mi424wr-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -47,6 +48,7 @@ obj-$(CONFIG_MACH_COMPEX)	+= compex-setu
+ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+ obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
+ obj-$(CONFIG_MACH_TW5334)	+= tw5334-setup.o
++obj-$(CONFIG_MACH_MI424WR)	+= mi424wr-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -243,6 +243,13 @@ config MACH_GTWX5715
+ 		"High Speed" UART is n/c (as far as I can tell)
+ 		20 Pin ARM/Xscale JTAG interface on J2
+ 
++config MACH_MI424WR
++	bool "Actiontec MI424WR"
++	depends on ARCH_IXP4XX
++	select PCI
++	help
++		Add support for the Actiontec MI424-WR.
++
+ comment "IXP4xx Options"
+ 
+ config IXP4XX_INDIRECT_PCI
+--- a/arch/arm/configs/ixp4xx_defconfig
++++ b/arch/arm/configs/ixp4xx_defconfig
+@@ -26,6 +26,7 @@ CONFIG_MACH_NAS100D=y
+ CONFIG_MACH_DSMG600=y
+ CONFIG_MACH_FSG=y
+ CONFIG_MACH_GTWX5715=y
++CONFIG_MACH_MI424WR=y
+ CONFIG_IXP4XX_QMGR=y
+ CONFIG_IXP4XX_NPE=y
+ # CONFIG_ARM_THUMB is not set
diff --git a/target/linux/ixp4xx/patches-2.6.37/190-cambria_support.patch b/target/linux/ixp4xx/patches-2.6.37/190-cambria_support.patch
new file mode 100644
index 0000000..683d8be
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/190-cambria_support.patch
@@ -0,0 +1,553 @@
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/cambria-pci.c
+@@ -0,0 +1,74 @@
++/*
++ * arch/arch/mach-ixp4xx/cambria-pci.c
++ *
++ * PCI setup routines for Gateworks Cambria series
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
++ *
++ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++
++#include <asm/mach/pci.h>
++
++extern void ixp4xx_pci_preinit(void);
++extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
++extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
++
++void __init cambria_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init cambria_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 1)
++		return IRQ_IXP4XX_GPIO11;
++	else if (slot == 2)
++		return IRQ_IXP4XX_GPIO10;
++	else if (slot == 3)
++		return IRQ_IXP4XX_GPIO9;
++	else if (slot == 4)
++		return IRQ_IXP4XX_GPIO8;
++	else return -1;
++}
++
++struct hw_pci cambria_pci __initdata = {
++	.nr_controllers = 1,
++	.preinit =        cambria_pci_preinit,
++	.swizzle =        pci_std_swizzle,
++	.setup =          ixp4xx_setup,
++	.scan =           ixp4xx_scan_bus,
++	.map_irq =        cambria_map_irq,
++};
++
++int __init cambria_pci_init(void)
++{
++	if (machine_is_cambria())
++		pci_common_init(&cambria_pci);
++	return 0;
++}
++
++subsys_initcall(cambria_pci_init);
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -0,0 +1,429 @@
++/*
++ * arch/arm/mach-ixp4xx/cambria-setup.c
++ *
++ * Board setup for the Gateworks Cambria series
++ *
++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ *
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Imre Kaloz <kaloz@openwrt.org>
++ */
++
++#include <linux/device.h>
++#include <linux/i2c.h>
++#include <linux/i2c-gpio.h>
++#include <linux/i2c/at24.h>
++#include <linux/if_ether.h>
++#include <linux/init.h>
++#include <linux/kernel.h>
++#include <linux/leds.h>
++#include <linux/memory.h>
++#include <linux/netdevice.h>
++#include <linux/serial.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++#include <linux/socket.h>
++#include <linux/types.h>
++#include <linux/tty.h>
++
++#include <mach/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++#include <asm/setup.h>
++
++struct cambria_board_info {
++	unsigned char	*model;
++	void		(*setup)(void);
++};
++
++static struct cambria_board_info *cambria_info __initdata;
++
++static struct flash_platform_data cambria_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource cambria_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device cambria_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &cambria_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &cambria_flash_resource,
++};
++
++static struct i2c_gpio_platform_data cambria_i2c_gpio_data = {
++	.sda_pin	= 7,
++	.scl_pin	= 6,
++};
++
++static struct platform_device cambria_i2c_gpio = {
++	.name		= "i2c-gpio",
++	.id		= 0,
++	.dev = {
++		.platform_data	= &cambria_i2c_gpio_data,
++	},
++};
++
++static struct eth_plat_info cambria_npec_data = {
++	.phy		= 1,
++	.rxq		= 4,
++	.txreadyq	= 21,
++};
++
++static struct eth_plat_info cambria_npea_data = {
++	.phy		= 2,
++	.rxq		= 2,
++	.txreadyq	= 19,
++};
++
++static struct platform_device cambria_npec_device = {
++	.name			= "ixp4xx_eth",
++	.id			= IXP4XX_ETH_NPEC,
++	.dev.platform_data	= &cambria_npec_data,
++};
++
++static struct platform_device cambria_npea_device = {
++	.name			= "ixp4xx_eth",
++	.id			= IXP4XX_ETH_NPEA,
++	.dev.platform_data	= &cambria_npea_data,
++};
++
++static struct resource cambria_uart_resource = {
++	.start	= IXP4XX_UART1_BASE_PHYS,
++	.end	= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++	.flags	= IORESOURCE_MEM,
++};
++
++static struct plat_serial8250_port cambria_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device cambria_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev = {
++		.platform_data	= cambria_uart_data,
++	},
++	.num_resources	= 1,
++	.resource	= &cambria_uart_resource,
++};
++
++static struct resource cambria_pata_resources[] = {
++	{
++		.flags	= IORESOURCE_MEM
++	},
++	{
++		.flags	= IORESOURCE_MEM,
++	},
++	{
++		.name	= "intrq",
++		.start	= IRQ_IXP4XX_GPIO12,
++		.end	= IRQ_IXP4XX_GPIO12,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct ixp4xx_pata_data cambria_pata_data = {
++	.cs0_bits	= 0xbfff3c03,
++	.cs1_bits	= 0xbfff3c03,
++};
++
++static struct platform_device cambria_pata = {
++	.name			= "pata_ixp4xx_cf",
++	.id			= 0,
++	.dev.platform_data      = &cambria_pata_data,
++	.num_resources		= ARRAY_SIZE(cambria_pata_resources),
++	.resource		= cambria_pata_resources,
++};
++
++static struct gpio_led cambria_gpio_leds[] = {
++	{
++		.name		= "user",  /* green led */
++		.gpio		= 5,
++		.active_low 	= 1,
++	}
++};
++
++static struct gpio_led_platform_data cambria_gpio_leds_data = {
++	.num_leds	= 1,
++	.leds		= cambria_gpio_leds,
++};
++
++static struct platform_device cambria_gpio_leds_device = {
++	.name		= "leds-gpio",
++	.id		= -1,
++	.dev.platform_data = &cambria_gpio_leds_data,
++};
++
++static struct latch_led cambria_latch_leds[] = {
++	{
++		.name	= "ledA",  /* green led */
++		.bit	= 0,
++	},
++	{
++		.name	= "ledB",  /* green led */
++		.bit	= 1,
++	},
++	{
++		.name	= "ledC",  /* green led */
++		.bit	= 2,
++	},
++	{
++		.name	= "ledD",  /* green led */
++		.bit	= 3,
++	},
++	{
++		.name	= "ledE",  /* green led */
++		.bit	= 4,
++	},
++	{
++		.name	= "ledF",  /* green led */
++		.bit	= 5,
++	},
++	{
++		.name	= "ledG",  /* green led */
++		.bit	= 6,
++	},
++	{
++		.name	= "ledH",  /* green led */
++		.bit	= 7,
++	}
++};
++
++static struct latch_led_platform_data cambria_latch_leds_data = {
++	.num_leds	= 8,
++	.leds		= cambria_latch_leds,
++	.mem		= 0x53F40000,
++};
++
++static struct platform_device cambria_latch_leds_device = {
++	.name		= "leds-latch",
++	.id		= -1,
++	.dev.platform_data = &cambria_latch_leds_data,
++};
++
++static struct resource cambria_usb0_resources[] = {
++	{
++		.start	= 0xCD000000,
++		.end	= 0xCD000300,
++		.flags	= IORESOURCE_MEM,
++	},
++	{
++		.start	= 32,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static struct resource cambria_usb1_resources[] = {
++	{
++		.start	= 0xCE000000,
++		.end	= 0xCE000300,
++		.flags	= IORESOURCE_MEM,
++	},
++	{
++		.start	= 33,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
++static u64 ehci_dma_mask = ~(u32)0;
++
++static struct platform_device cambria_usb0_device =  {
++	.name		= "ixp4xx-ehci",
++	.id		= 0,
++	.resource	= cambria_usb0_resources,
++	.num_resources	= ARRAY_SIZE(cambria_usb0_resources),
++	.dev = {
++		.dma_mask		= &ehci_dma_mask,
++		.coherent_dma_mask	= 0xffffffff,
++	},
++};
++
++static struct platform_device cambria_usb1_device = {
++	.name		= "ixp4xx-ehci",
++	.id		= 1,
++	.resource	= cambria_usb1_resources,
++	.num_resources	= ARRAY_SIZE(cambria_usb1_resources),
++	.dev = {
++		.dma_mask		= &ehci_dma_mask,
++		.coherent_dma_mask	= 0xffffffff,
++	},
++};
++
++static struct platform_device *cambria_devices[] __initdata = {
++	&cambria_i2c_gpio,
++	&cambria_flash,
++	&cambria_uart,
++};
++
++static void __init cambria_gw23xx_setup(void)
++{
++	platform_device_register(&cambria_npec_device);
++	platform_device_register(&cambria_npea_device);
++}
++
++static void __init cambria_gw2350_setup(void)
++{
++	platform_device_register(&cambria_npec_device);
++	platform_device_register(&cambria_npea_device);
++
++	platform_device_register(&cambria_usb0_device);
++	platform_device_register(&cambria_usb1_device);
++
++	platform_device_register(&cambria_gpio_leds_device);
++}
++
++static void __init cambria_gw2358_setup(void)
++{
++	platform_device_register(&cambria_npec_device);
++	platform_device_register(&cambria_npea_device);
++
++	platform_device_register(&cambria_usb0_device);
++	platform_device_register(&cambria_usb1_device);
++
++	platform_device_register(&cambria_pata);
++
++	platform_device_register(&cambria_latch_leds_device);
++}
++
++static struct cambria_board_info cambria_boards[] __initdata = {
++	{
++		.model	= "GW2350",
++		.setup	= cambria_gw2350_setup,
++	}, {
++		.model	= "GW2358",
++		.setup	= cambria_gw2358_setup,
++	}
++};
++
++static struct cambria_board_info * __init cambria_find_board_info(char *model)
++{
++	int i;
++	model[6] = '\0';
++
++	for (i = 0; i < ARRAY_SIZE(cambria_boards); i++) {
++		struct cambria_board_info *info = &cambria_boards[i];
++		if (strcmp(info->model, model) == 0)
++			return info;
++	}
++
++	return NULL;
++}
++
++static struct memory_accessor *at24_mem_acc;
++
++static void at24_setup(struct memory_accessor *mem_acc, void *context)
++{
++	char mac_addr[ETH_ALEN];
++	char model[7];
++
++	at24_mem_acc = mem_acc;
++
++	/* Read MAC addresses */
++	if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x0, 6) == 6) {
++		memcpy(&cambria_npec_data.hwaddr, mac_addr, ETH_ALEN);
++	}
++	if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x6, 6) == 6) {
++		memcpy(&cambria_npea_data.hwaddr, mac_addr, ETH_ALEN);
++	}
++
++	/* Read the first 6 bytes of the model number */
++	if (at24_mem_acc->read(at24_mem_acc, model, 0x20, 6) == 6) {
++		cambria_info = cambria_find_board_info(model);
++	}
++
++}
++
++static struct at24_platform_data cambria_eeprom_info = {
++	.byte_len	= 1024,
++	.page_size	= 16,
++	.flags		= AT24_FLAG_READONLY,
++	.setup		= at24_setup,
++};
++
++static struct i2c_board_info __initdata cambria_i2c_board_info[] = {
++	{
++		I2C_BOARD_INFO("ds1672", 0x68),
++	},
++	{
++		I2C_BOARD_INFO("ad7418", 0x28),
++	},
++	{
++		I2C_BOARD_INFO("24c08", 0x51),
++		.platform_data	= &cambria_eeprom_info
++	},
++};
++
++static void __init cambria_init(void)
++{
++	ixp4xx_sys_init();
++
++	cambria_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	cambria_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++	platform_add_devices(cambria_devices, ARRAY_SIZE(cambria_devices));
++
++	cambria_pata_resources[0].start = 0x53e00000;
++	cambria_pata_resources[0].end = 0x53e3ffff;
++
++	cambria_pata_resources[1].start = 0x53e40000;
++	cambria_pata_resources[1].end = 0x53e7ffff;
++
++	cambria_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
++	cambria_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
++
++	i2c_register_board_info(0, cambria_i2c_board_info,
++				ARRAY_SIZE(cambria_i2c_board_info));
++}
++
++static int __init cambria_model_setup(void)
++{
++	if (!machine_is_cambria())
++		return 0;
++
++	if (cambria_info) {
++		printk(KERN_DEBUG "Running on Gateworks Cambria %s\n",
++				cambria_info->model);
++		cambria_info->setup();
++	} else {
++		printk(KERN_INFO "Unknown/missing Cambria model number"
++				" -- defaults will be used\n");
++		cambria_gw23xx_setup();
++	}
++
++	return 0;
++}
++late_initcall(cambria_model_setup);
++
++MACHINE_START(CAMBRIA, "Gateworks Cambria series")
++	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= cambria_init,
++MACHINE_END
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -25,6 +25,14 @@ config MACH_AVILA
+ 	  Avila Network Platform. For more information on this platform,
+ 	  see <file:Documentation/arm/IXP4xx>.
+ 
++config MACH_CAMBRIA
++	bool "Cambria"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support the Gateworks
++	  Cambria series. For more information on this platform,
++	  see <file:Documentation/arm/IXP4xx>.
++
+ config MACH_LOFT
+     bool "Loft"
+     depends on MACH_AVILA
+@@ -222,7 +230,7 @@ config CPU_IXP46X
+ 
+ config CPU_IXP43X
+ 	bool
+-	depends on MACH_KIXRP435
++	depends on MACH_KIXRP435 || MACH_CAMBRIA
+ 	default y
+ 
+ config MACH_GTWX5715
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -7,6 +7,7 @@ obj-pci-n	:=
+ 
+ obj-pci-$(CONFIG_ARCH_IXDP4XX)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_AVILA)		+= avila-pci.o
++obj-pci-$(CONFIG_MACH_CAMBRIA)		+= cambria-pci.o
+ obj-pci-$(CONFIG_MACH_IXDPG425)		+= ixdpg425-pci.o
+ obj-pci-$(CONFIG_ARCH_ADI_COYOTE)	+= coyote-pci.o
+ obj-pci-$(CONFIG_MACH_GTWX5715)		+= gtwx5715-pci.o
+@@ -30,6 +31,7 @@ obj-y	+= common.o
+ 
+ obj-$(CONFIG_ARCH_IXDP4XX)	+= ixdp425-setup.o
+ obj-$(CONFIG_MACH_AVILA)	+= avila-setup.o
++obj-$(CONFIG_MACH_CAMBRIA)	+= cambria-setup.o
+ obj-$(CONFIG_MACH_IXDPG425)	+= coyote-setup.o
+ obj-$(CONFIG_ARCH_ADI_COYOTE)	+= coyote-setup.o
+ obj-$(CONFIG_MACH_GTWX5715)	+= gtwx5715-setup.o
diff --git a/target/linux/ixp4xx/patches-2.6.37/191-cambria_optional_uart.patch b/target/linux/ixp4xx/patches-2.6.37/191-cambria_optional_uart.patch
new file mode 100644
index 0000000..099980b
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/191-cambria_optional_uart.patch
@@ -0,0 +1,217 @@
+--- a/arch/arm/mach-ixp4xx/cambria-setup.c
++++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -34,6 +34,7 @@
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
+ #include <asm/setup.h>
++#include <linux/irq.h>
+ 
+ struct cambria_board_info {
+ 	unsigned char	*model;
+@@ -127,6 +128,45 @@ static struct platform_device cambria_ua
+ 	.resource	= &cambria_uart_resource,
+ };
+ 
++static struct resource cambria_optional_uart_resources[] = {
++	{
++		.start	= 0x52000000,
++		.end	= 0x52000fff,
++		.flags	= IORESOURCE_MEM
++	},
++	{
++		.start	= 0x53000000,
++		.end	= 0x53000fff,
++		.flags	= IORESOURCE_MEM
++	}
++};
++
++static struct plat_serial8250_port cambria_optional_uart_data[] = {
++	{
++		.flags		= UPF_BOOT_AUTOCONF,
++		.iotype		= UPIO_MEM_DELAY,
++		.regshift	= 0,
++		.uartclk	= 1843200,
++		.rw_delay	= 2,
++	},
++	{
++		.flags		= UPF_BOOT_AUTOCONF,
++		.iotype		= UPIO_MEM_DELAY,
++		.regshift	= 0,
++		.uartclk	= 1843200,
++		.rw_delay	= 2,
++	},
++  { },
++};
++
++static struct platform_device cambria_optional_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM1,
++	.dev.platform_data	= cambria_optional_uart_data,
++	.num_resources	= 2,
++	.resource	= cambria_optional_uart_resources,
++};
++
+ static struct resource cambria_pata_resources[] = {
+ 	{
+ 		.flags	= IORESOURCE_MEM
+@@ -283,6 +323,19 @@ static void __init cambria_gw23xx_setup(
+ 
+ static void __init cambria_gw2350_setup(void)
+ {
++	*IXP4XX_EXP_CS2 = 0xBFFF3C43;
++	set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
++	cambria_optional_uart_data[0].mapbase	= 0x52FF0000;
++	cambria_optional_uart_data[0].membase	= (void __iomem *)ioremap(0x52FF0000, 0x0fff);
++	cambria_optional_uart_data[0].irq		= IRQ_IXP4XX_GPIO3;
++
++	*IXP4XX_EXP_CS3 = 0xBFFF3C43;
++	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
++	cambria_optional_uart_data[1].mapbase	= 0x53FF0000;
++	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53FF0000, 0x0fff);
++	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
++
++	platform_device_register(&cambria_optional_uart);
+ 	platform_device_register(&cambria_npec_device);
+ 	platform_device_register(&cambria_npea_device);
+ 
+@@ -294,6 +347,19 @@ static void __init cambria_gw2350_setup(
+ 
+ static void __init cambria_gw2358_setup(void)
+ {
++	*IXP4XX_EXP_CS3 = 0xBFFF3C43;
++	set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
++	cambria_optional_uart_data[0].mapbase	= 0x53FC0000;
++	cambria_optional_uart_data[0].membase	= (void __iomem *)ioremap(0x53FC0000, 0x0fff);
++	cambria_optional_uart_data[0].irq		= IRQ_IXP4XX_GPIO3;
++
++	set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
++	cambria_optional_uart_data[1].mapbase	= 0x53F80000;
++	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53F80000, 0x0fff);
++	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
++
++	platform_device_register(&cambria_optional_uart);
++
+ 	platform_device_register(&cambria_npec_device);
+ 	platform_device_register(&cambria_npea_device);
+ 
+--- a/include/linux/serial_8250.h
++++ b/include/linux/serial_8250.h
+@@ -27,6 +27,7 @@ struct plat_serial8250_port {
+ 	void            *private_data;
+ 	unsigned char	regshift;	/* register shift */
+ 	unsigned char	iotype;		/* UPIO_* */
++	unsigned int rw_delay;	/* udelay for slower busses IXP4XX Expansion Bus */
+ 	unsigned char	hub6;
+ 	upf_t		flags;		/* UPF_* flags */
+ 	unsigned int	type;		/* If UPF_FIXED_TYPE */
+--- a/include/linux/serial_core.h
++++ b/include/linux/serial_core.h
+@@ -311,6 +311,7 @@ struct uart_port {
+ #define UPIO_TSI		(5)			/* Tsi108/109 type IO */
+ #define UPIO_DWAPB		(6)			/* DesignWare APB UART */
+ #define UPIO_RM9000		(7)			/* RM9000 type IO */
++#define UPIO_MEM_DELAY	(8)
+ 
+ 	unsigned int		read_status_mask;	/* driver specific */
+ 	unsigned int		ignore_status_mask;	/* driver specific */
+@@ -353,6 +354,7 @@ struct uart_port {
+ 
+ 	unsigned int		mctrl;			/* current modem ctrl settings */
+ 	unsigned int		timeout;		/* character-based timeout */
++	unsigned int		rw_delay;		/* udelay for slow busses, IXP4XX Expansion Bus */
+ 	unsigned int		type;			/* port type */
+ 	const struct uart_ops	*ops;
+ 	unsigned int		custom_divisor;
+--- a/drivers/serial/8250.c
++++ b/drivers/serial/8250.c
+@@ -412,6 +412,20 @@ static void mem_serial_out(struct uart_p
+ 	writeb(value, p->membase + offset);
+ }
+ 
++static unsigned int memdelay_serial_in(struct uart_port *p, int offset)
++{
++	struct uart_8250_port *up = (struct uart_8250_port *)p;
++	udelay(up->port.rw_delay);
++	return mem_serial_in(p, offset);
++}
++
++static void memdelay_serial_out(struct uart_port *p, int offset, int value)
++{
++	struct uart_8250_port *up = (struct uart_8250_port *)p;
++	udelay(up->port.rw_delay);
++	mem_serial_out(p, offset, value);
++}
++
+ static void mem32_serial_out(struct uart_port *p, int offset, int value)
+ {
+ 	offset = map_8250_out_reg(p, offset) << p->regshift;
+@@ -503,6 +517,11 @@ static void set_io_from_upio(struct uart
+ 		p->serial_out = mem32_serial_out;
+ 		break;
+ 
++	case UPIO_MEM_DELAY:
++		p->serial_in = memdelay_serial_in;
++		p->serial_out = memdelay_serial_out;
++		break;
++
+ 	case UPIO_AU:
+ 		p->serial_in = au_serial_in;
+ 		p->serial_out = au_serial_out;
+@@ -534,6 +553,7 @@ serial_out_sync(struct uart_8250_port *u
+ 	switch (p->iotype) {
+ 	case UPIO_MEM:
+ 	case UPIO_MEM32:
++	case UPIO_MEM_DELAY:
+ 	case UPIO_AU:
+ 	case UPIO_DWAPB:
+ 		p->serial_out(p, offset, value);
+@@ -2476,6 +2496,7 @@ static int serial8250_request_std_resour
+ 	case UPIO_MEM32:
+ 	case UPIO_MEM:
+ 	case UPIO_DWAPB:
++	case UPIO_MEM_DELAY:
+ 		if (!up->port.mapbase)
+ 			break;
+ 
+@@ -2513,6 +2534,7 @@ static void serial8250_release_std_resou
+ 	case UPIO_MEM32:
+ 	case UPIO_MEM:
+ 	case UPIO_DWAPB:
++	case UPIO_MEM_DELAY:
+ 		if (!up->port.mapbase)
+ 			break;
+ 
+@@ -3024,6 +3046,7 @@ static int __devinit serial8250_probe(st
+ 		port.set_termios	= p->set_termios;
+ 		port.pm			= p->pm;
+ 		port.dev		= &dev->dev;
++		port.rw_delay		= p->rw_delay;
+ 		port.irqflags		|= irqflag;
+ 		ret = serial8250_register_port(&port);
+ 		if (ret < 0) {
+@@ -3173,6 +3196,7 @@ int serial8250_register_port(struct uart
+ 		uart->port.iotype       = port->iotype;
+ 		uart->port.flags        = port->flags | UPF_BOOT_AUTOCONF;
+ 		uart->port.mapbase      = port->mapbase;
++		uart->port.rw_delay			= port->rw_delay;
+ 		uart->port.private_data = port->private_data;
+ 		if (port->dev)
+ 			uart->port.dev = port->dev;
+--- a/drivers/serial/serial_core.c
++++ b/drivers/serial/serial_core.c
+@@ -2130,6 +2130,7 @@ uart_report_port(struct uart_driver *drv
+ 		snprintf(address, sizeof(address),
+ 			 "I/O 0x%lx offset 0x%x", port->iobase, port->hub6);
+ 		break;
++	case UPIO_MEM_DELAY:
+ 	case UPIO_MEM:
+ 	case UPIO_MEM32:
+ 	case UPIO_AU:
+@@ -2550,6 +2551,7 @@ int uart_match_port(struct uart_port *po
+ 	case UPIO_HUB6:
+ 		return (port1->iobase == port2->iobase) &&
+ 		       (port1->hub6   == port2->hub6);
++	case UPIO_MEM_DELAY:
+ 	case UPIO_MEM:
+ 	case UPIO_MEM32:
+ 	case UPIO_AU:
diff --git a/target/linux/ixp4xx/patches-2.6.37/192-cambria_gpio_device.patch b/target/linux/ixp4xx/patches-2.6.37/192-cambria_gpio_device.patch
new file mode 100644
index 0000000..d785c3a
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/192-cambria_gpio_device.patch
@@ -0,0 +1,46 @@
+--- a/arch/arm/mach-ixp4xx/cambria-setup.c
++++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -214,6 +214,20 @@ static struct platform_device cambria_gp
+ 	.dev.platform_data = &cambria_gpio_leds_data,
+ };
+ 
++static struct resource cambria_gpio_resources[] = {
++	{
++		.name = "gpio",
++		.flags  = 0,
++	},
++};
++
++static struct platform_device cambria_gpio = {
++	.name     = "GPIODEV",
++	.id     = -1,
++	.num_resources    = ARRAY_SIZE(cambria_gpio_resources),
++	.resource   = cambria_gpio_resources,
++};
++
+ static struct latch_led cambria_latch_leds[] = {
+ 	{
+ 		.name	= "ledA",  /* green led */
+@@ -335,6 +349,11 @@ static void __init cambria_gw2350_setup(
+ 	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53FF0000, 0x0fff);
+ 	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+ 
++	cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\
++																		(1 << 5) | (1 << 8) | (1 << 9) | (1 << 12);
++	cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
++
++	platform_device_register(&cambria_gpio);
+ 	platform_device_register(&cambria_optional_uart);
+ 	platform_device_register(&cambria_npec_device);
+ 	platform_device_register(&cambria_npea_device);
+@@ -358,6 +377,10 @@ static void __init cambria_gw2358_setup(
+ 	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53F80000, 0x0fff);
+ 	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+ 
++	cambria_gpio_resources[0].start = (1 << 14);
++	cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
++
++	platform_device_register(&cambria_gpio);
+ 	platform_device_register(&cambria_optional_uart);
+ 
+ 	platform_device_register(&cambria_npec_device);
diff --git a/target/linux/ixp4xx/patches-2.6.37/193-cambria_pld_gpio.patch b/target/linux/ixp4xx/patches-2.6.37/193-cambria_pld_gpio.patch
new file mode 100644
index 0000000..171898d
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/193-cambria_pld_gpio.patch
@@ -0,0 +1,107 @@
+--- a/arch/arm/mach-ixp4xx/cambria-setup.c
++++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -12,11 +12,14 @@
+  */
+ 
+ #include <linux/device.h>
++#include <linux/gpio_buttons.h>
+ #include <linux/i2c.h>
+ #include <linux/i2c-gpio.h>
+ #include <linux/i2c/at24.h>
++#include <linux/i2c/gw_i2c_pld.h>
+ #include <linux/if_ether.h>
+ #include <linux/init.h>
++#include <linux/input.h>
+ #include <linux/kernel.h>
+ #include <linux/leds.h>
+ #include <linux/memory.h>
+@@ -323,6 +326,39 @@ static struct platform_device cambria_us
+ 	},
+ };
+ 
++static struct gw_i2c_pld_platform_data gw_i2c_pld_data0 = {
++	.gpio_base	= 16,
++	.nr_gpio	= 8,
++};
++
++static struct gw_i2c_pld_platform_data gw_i2c_pld_data1 = {
++	.gpio_base	= 24,
++	.nr_gpio	= 2,
++};
++
++
++static struct gpio_button cambria_gpio_buttons[] = {
++	{
++		.desc		= "user",
++		.type		= EV_KEY,
++		.code		= BTN_0,
++		.threshold	= 2,
++		.gpio		= 25,
++	}
++};
++
++static struct gpio_buttons_platform_data cambria_gpio_buttons_data = {
++	.poll_interval	= 500,
++	.nbuttons	= 1,
++	.buttons	= cambria_gpio_buttons,	
++};
++
++static struct platform_device cambria_gpio_buttons_device = {
++	.name			= "gpio-buttons",
++	.id			= -1,
++	.dev.platform_data	= &cambria_gpio_buttons_data,
++};
++
+ static struct platform_device *cambria_devices[] __initdata = {
+ 	&cambria_i2c_gpio,
+ 	&cambria_flash,
+@@ -331,6 +367,11 @@ static struct platform_device *cambria_d
+ 
+ static void __init cambria_gw23xx_setup(void)
+ {
++	cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\
++																		(1 << 5) | (1 << 8) | (1 << 9) | (1 << 12);
++	cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
++
++	platform_device_register(&cambria_gpio);
+ 	platform_device_register(&cambria_npec_device);
+ 	platform_device_register(&cambria_npea_device);
+ }
+@@ -377,7 +418,8 @@ static void __init cambria_gw2358_setup(
+ 	cambria_optional_uart_data[1].membase	= (void __iomem *)ioremap(0x53F80000, 0x0fff);
+ 	cambria_optional_uart_data[1].irq		= IRQ_IXP4XX_GPIO4;
+ 
+-	cambria_gpio_resources[0].start = (1 << 14);
++	cambria_gpio_resources[0].start = (1 << 14) | (1 << 16) | (1 << 17) | (1 << 18) |\
++																		(1 << 19) | (1 << 20) | (1 << 24) | (1 << 25);
+ 	cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
+ 
+ 	platform_device_register(&cambria_gpio);
+@@ -391,7 +433,12 @@ static void __init cambria_gw2358_setup(
+ 
+ 	platform_device_register(&cambria_pata);
+ 
++	cambria_gpio_leds[0].gpio = 24;
++	platform_device_register(&cambria_gpio_leds_device);
++
+ 	platform_device_register(&cambria_latch_leds_device);
++
++	platform_device_register(&cambria_gpio_buttons_device);
+ }
+ 
+ static struct cambria_board_info cambria_boards[] __initdata = {
+@@ -460,6 +507,14 @@ static struct i2c_board_info __initdata
+ 		I2C_BOARD_INFO("24c08", 0x51),
+ 		.platform_data	= &cambria_eeprom_info
+ 	},
++	{
++		I2C_BOARD_INFO("gw_i2c_pld", 0x56),
++		.platform_data	= &gw_i2c_pld_data0,
++	},
++	{
++		I2C_BOARD_INFO("gw_i2c_pld", 0x57),
++		.platform_data	= &gw_i2c_pld_data1,
++	},
+ };
+ 
+ static void __init cambria_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.37/201-npe_driver_print_license_location.patch b/target/linux/ixp4xx/patches-2.6.37/201-npe_driver_print_license_location.patch
new file mode 100644
index 0000000..e6bbbc3
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/201-npe_driver_print_license_location.patch
@@ -0,0 +1,11 @@
+--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c
++++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+@@ -582,6 +582,8 @@ int npe_load_firmware(struct npe *npe, c
+ 	npe_reset(npe);
+ #endif
+ 
++	print_npe(KERN_INFO, npe, "firmware's license can be found in /usr/share/doc/LICENSE.IPL\n");
++
+ 	print_npe(KERN_INFO, npe, "firmware functionality 0x%X, "
+ 		  "revision 0x%X:%X\n", (image->id >> 16) & 0xFF,
+ 		  (image->id >> 8) & 0xFF, image->id & 0xFF);
diff --git a/target/linux/ixp4xx/patches-2.6.37/203-npe_driver_mask_phy_features.patch b/target/linux/ixp4xx/patches-2.6.37/203-npe_driver_mask_phy_features.patch
new file mode 100644
index 0000000..54e3fd0
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/203-npe_driver_mask_phy_features.patch
@@ -0,0 +1,13 @@
+--- a/drivers/net/arm/ixp4xx_eth.c
++++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -1232,6 +1232,10 @@ static int __devinit eth_init_one(struct
+ 	if ((err = IS_ERR(port->phydev)))
+ 		goto err_free_mem;
+ 
++	/* mask with MAC supported features */
++	port->phydev->supported &= PHY_BASIC_FEATURES;
++	port->phydev->advertising = port->phydev->supported;
++
+ 	port->phydev->irq = PHY_POLL;
+ 
+ 	if ((err = register_netdev(dev)))
diff --git a/target/linux/ixp4xx/patches-2.6.37/205-npe_driver_separate_phy_functions.patch b/target/linux/ixp4xx/patches-2.6.37/205-npe_driver_separate_phy_functions.patch
new file mode 100644
index 0000000..10e8cbe
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/205-npe_driver_separate_phy_functions.patch
@@ -0,0 +1,119 @@
+--- a/drivers/net/arm/ixp4xx_eth.c
++++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -397,6 +397,50 @@ static void ixp4xx_adjust_link(struct ne
+ 	       dev->name, port->speed, port->duplex ? "full" : "half");
+ }
+ 
++static int ixp4xx_phy_connect(struct net_device *dev)
++{
++	struct port *port = netdev_priv(dev);
++	struct eth_plat_info *plat = port->plat;
++	char phy_id[MII_BUS_ID_SIZE + 3];
++
++	snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, "0", plat->phy);
++	port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, 0,
++				   PHY_INTERFACE_MODE_MII);
++	if (IS_ERR(port->phydev)) {
++		printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
++		return PTR_ERR(port->phydev);
++	}
++
++	/* mask with MAC supported features */
++	port->phydev->supported &= PHY_BASIC_FEATURES;
++	port->phydev->advertising = port->phydev->supported;
++
++	port->phydev->irq = PHY_POLL;
++
++	return 0;
++}
++
++static void ixp4xx_phy_disconnect(struct net_device *dev)
++{
++	struct port *port = netdev_priv(dev);
++
++	phy_disconnect(port->phydev);
++}
++
++static void ixp4xx_phy_start(struct net_device *dev)
++{
++	struct port *port = netdev_priv(dev);
++
++	port->speed = 0;	/* force "link up" message */
++	phy_start(port->phydev);
++}
++
++static void ixp4xx_phy_stop(struct net_device *dev)
++{
++	struct port *port = netdev_priv(dev);
++
++	phy_stop(port->phydev);
++}
+ 
+ static inline void debug_pkt(struct net_device *dev, const char *func,
+ 			     u8 *data, int len)
+@@ -1020,8 +1064,7 @@ static int eth_open(struct net_device *d
+ 		return err;
+ 	}
+ 
+-	port->speed = 0;	/* force "link up" message */
+-	phy_start(port->phydev);
++	ixp4xx_phy_start(dev);
+ 
+ 	for (i = 0; i < ETH_ALEN; i++)
+ 		__raw_writel(dev->dev_addr[i], &port->regs->hw_addr[i]);
+@@ -1142,7 +1185,7 @@ static int eth_close(struct net_device *
+ 		printk(KERN_CRIT "%s: unable to disable loopback\n",
+ 		       dev->name);
+ 
+-	phy_stop(port->phydev);
++	ixp4xx_phy_stop(dev);
+ 
+ 	if (!ports_open)
+ 		qmgr_disable_irq(TXDONE_QUEUE);
+@@ -1168,7 +1211,6 @@ static int __devinit eth_init_one(struct
+ 	struct net_device *dev;
+ 	struct eth_plat_info *plat = pdev->dev.platform_data;
+ 	u32 regs_phys;
+-	char phy_id[MII_BUS_ID_SIZE + 3];
+ 	int err;
+ 
+ 	if (!(dev = alloc_etherdev(sizeof(struct port))))
+@@ -1226,18 +1268,10 @@ static int __devinit eth_init_one(struct
+ 	__raw_writel(DEFAULT_CORE_CNTRL, &port->regs->core_control);
+ 	udelay(50);
+ 
+-	snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, "0", plat->phy);
+-	port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, 0,
+-				   PHY_INTERFACE_MODE_MII);
+-	if ((err = IS_ERR(port->phydev)))
++	err = ixp4xx_phy_connect(dev);
++	if (err)
+ 		goto err_free_mem;
+ 
+-	/* mask with MAC supported features */
+-	port->phydev->supported &= PHY_BASIC_FEATURES;
+-	port->phydev->advertising = port->phydev->supported;
+-
+-	port->phydev->irq = PHY_POLL;
+-
+ 	if ((err = register_netdev(dev)))
+ 		goto err_phy_dis;
+ 
+@@ -1247,7 +1281,7 @@ static int __devinit eth_init_one(struct
+ 	return 0;
+ 
+ err_phy_dis:
+-	phy_disconnect(port->phydev);
++	ixp4xx_phy_disconnect(dev);
+ err_free_mem:
+ 	npe_port_tab[NPE_ID(port->id)] = NULL;
+ 	platform_set_drvdata(pdev, NULL);
+@@ -1265,7 +1299,7 @@ static int __devexit eth_remove_one(stru
+ 	struct port *port = netdev_priv(dev);
+ 
+ 	unregister_netdev(dev);
+-	phy_disconnect(port->phydev);
++	ixp4xx_phy_disconnect(dev);
+ 	npe_port_tab[NPE_ID(port->id)] = NULL;
+ 	platform_set_drvdata(pdev, NULL);
+ 	npe_release(port->npe);
diff --git a/target/linux/ixp4xx/patches-2.6.37/206-npe_driver_add_update_link_function.patch b/target/linux/ixp4xx/patches-2.6.37/206-npe_driver_add_update_link_function.patch
new file mode 100644
index 0000000..6e5b7e0
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/206-npe_driver_add_update_link_function.patch
@@ -0,0 +1,98 @@
+--- a/drivers/net/arm/ixp4xx_eth.c
++++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -169,7 +169,7 @@ struct port {
+ 	struct desc *desc_tab;	/* coherent */
+ 	u32 desc_tab_phys;
+ 	int id;			/* logical port ID */
+-	int speed, duplex;
++	int link, speed, duplex;
+ 	u8 firmware[4];
+ };
+ 
+@@ -366,37 +366,52 @@ static void ixp4xx_mdio_remove(void)
+ 	mdiobus_free(mdio_bus);
+ }
+ 
+-
+-static void ixp4xx_adjust_link(struct net_device *dev)
++static void ixp4xx_update_link(struct net_device *dev)
+ {
+ 	struct port *port = netdev_priv(dev);
+-	struct phy_device *phydev = port->phydev;
+ 
+-	if (!phydev->link) {
+-		if (port->speed) {
+-			port->speed = 0;
+-			printk(KERN_INFO "%s: link down\n", dev->name);
+-		}
++	if (!port->link) {
++		netif_carrier_off(dev);
++		printk(KERN_INFO "%s: link down\n", dev->name);
+ 		return;
+ 	}
+ 
+-	if (port->speed == phydev->speed && port->duplex == phydev->duplex)
+-		return;
+-
+-	port->speed = phydev->speed;
+-	port->duplex = phydev->duplex;
+-
+-	if (port->duplex)
++	if (port->duplex == DUPLEX_FULL)
+ 		__raw_writel(DEFAULT_TX_CNTRL0 & ~TX_CNTRL0_HALFDUPLEX,
+ 			     &port->regs->tx_control[0]);
+ 	else
+ 		__raw_writel(DEFAULT_TX_CNTRL0 | TX_CNTRL0_HALFDUPLEX,
+ 			     &port->regs->tx_control[0]);
+ 
++	netif_carrier_on(dev);
+ 	printk(KERN_INFO "%s: link up, speed %u Mb/s, %s duplex\n",
+ 	       dev->name, port->speed, port->duplex ? "full" : "half");
+ }
+ 
++static void ixp4xx_adjust_link(struct net_device *dev)
++{
++	struct port *port = netdev_priv(dev);
++	struct phy_device *phydev = port->phydev;
++	int status_change = 0;
++
++	if (phydev->link) {
++		if (port->duplex != phydev->duplex
++		    || port->speed != phydev->speed) {
++			status_change = 1;
++		}
++	}
++
++	if (phydev->link != port->link)
++		status_change = 1;
++
++	port->link = phydev->link;
++	port->speed = phydev->speed;
++	port->duplex = phydev->duplex;
++
++	if (status_change)
++		ixp4xx_update_link(dev);
++}
++
+ static int ixp4xx_phy_connect(struct net_device *dev)
+ {
+ 	struct port *port = netdev_priv(dev);
+@@ -431,7 +446,6 @@ static void ixp4xx_phy_start(struct net_
+ {
+ 	struct port *port = netdev_priv(dev);
+ 
+-	port->speed = 0;	/* force "link up" message */
+ 	phy_start(port->phydev);
+ }
+ 
+@@ -1275,6 +1289,10 @@ static int __devinit eth_init_one(struct
+ 	if ((err = register_netdev(dev)))
+ 		goto err_phy_dis;
+ 
++	port->link = 0;
++	port->speed = 0;
++	port->duplex = -1;
++
+ 	printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, plat->phy,
+ 	       npe_name(port->npe));
+ 
diff --git a/target/linux/ixp4xx/patches-2.6.37/207-npe_driver_multiphy_support.patch b/target/linux/ixp4xx/patches-2.6.37/207-npe_driver_multiphy_support.patch
new file mode 100644
index 0000000..907305f
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/207-npe_driver_multiphy_support.patch
@@ -0,0 +1,154 @@
+TODO: take care of additional PHYs through the PHY abstraction layer
+
+--- a/arch/arm/mach-ixp4xx/include/mach/platform.h
++++ b/arch/arm/mach-ixp4xx/include/mach/platform.h
+@@ -72,7 +72,7 @@ extern unsigned long ixp4xx_exp_bus_size
+ /*
+  * Clock Speed Definitions.
+  */
+-#define IXP4XX_PERIPHERAL_BUS_CLOCK 	(66) /* 66Mhzi APB BUS   */ 
++#define IXP4XX_PERIPHERAL_BUS_CLOCK 	(66) /* 66Mhzi APB BUS   */
+ #define IXP4XX_UART_XTAL        	14745600
+ 
+ /*
+@@ -95,12 +95,23 @@ struct sys_timer;
+ #define IXP4XX_ETH_NPEB		0x10
+ #define IXP4XX_ETH_NPEC		0x20
+ 
++#define IXP4XX_ETH_PHY_MAX_ADDR	32
++
+ /* Information about built-in Ethernet MAC interfaces */
+ struct eth_plat_info {
+ 	u8 phy;		/* MII PHY ID, 0 - 31 */
+ 	u8 rxq;		/* configurable, currently 0 - 31 only */
+ 	u8 txreadyq;
+ 	u8 hwaddr[6];
++
++	u32 phy_mask;
++#if 0
++	int speed;
++	int duplex;
++#else
++	int speed_10;
++	int half_duplex;
++#endif
+ };
+ 
+ /* Information about built-in HSS (synchronous serial) interfaces */
+--- a/drivers/net/arm/ixp4xx_eth.c
++++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -418,6 +418,37 @@ static int ixp4xx_phy_connect(struct net
+ 	struct eth_plat_info *plat = port->plat;
+ 	char phy_id[MII_BUS_ID_SIZE + 3];
+ 
++	if (plat->phy == IXP4XX_ETH_PHY_MAX_ADDR) {
++#if 0
++		switch (plat->speed) {
++		case SPEED_10:
++		case SPEED_100:
++			break;
++		default:
++			printk(KERN_ERR "%s: invalid speed (%d)\n",
++					dev->name, plat->speed);
++			return -EINVAL;
++		}
++
++		switch (plat->duplex) {
++		case DUPLEX_HALF:
++		case DUPLEX_FULL:
++			break;
++		default:
++			printk(KERN_ERR "%s: invalid duplex mode (%d)\n",
++					dev->name, plat->duplex);
++			return -EINVAL;
++		}
++		port->speed = plat->speed;
++		port->duplex = plat->duplex;
++#else
++		port->speed = plat->speed_10 ? SPEED_10 : SPEED_100;
++		port->duplex = plat->half_duplex ? DUPLEX_HALF : DUPLEX_FULL;
++#endif
++
++		return 0;
++	}
++
+ 	snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, "0", plat->phy);
+ 	port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, 0,
+ 				   PHY_INTERFACE_MODE_MII);
+@@ -439,21 +470,32 @@ static void ixp4xx_phy_disconnect(struct
+ {
+ 	struct port *port = netdev_priv(dev);
+ 
+-	phy_disconnect(port->phydev);
++	if (port->phydev)
++		phy_disconnect(port->phydev);
+ }
+ 
+ static void ixp4xx_phy_start(struct net_device *dev)
+ {
+ 	struct port *port = netdev_priv(dev);
+ 
+-	phy_start(port->phydev);
++	if (port->phydev) {
++		phy_start(port->phydev);
++	} else {
++		port->link = 1;
++		ixp4xx_update_link(dev);
++	}
+ }
+ 
+ static void ixp4xx_phy_stop(struct net_device *dev)
+ {
+ 	struct port *port = netdev_priv(dev);
+ 
+-	phy_stop(port->phydev);
++	if (port->phydev) {
++		phy_stop(port->phydev);
++	} else {
++		port->link = 0;
++		ixp4xx_update_link(dev);
++	}
+ }
+ 
+ static inline void debug_pkt(struct net_device *dev, const char *func,
+@@ -841,6 +883,9 @@ static int eth_ioctl(struct net_device *
+ 	if (!netif_running(dev))
+ 		return -EINVAL;
+ 
++	if (!port->phydev)
++		return -EOPNOTSUPP;
++
+ 	return phy_mii_ioctl(port->phydev, req, cmd);
+ }
+ 
+@@ -860,18 +905,30 @@ static void ixp4xx_get_drvinfo(struct ne
+ static int ixp4xx_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+ {
+ 	struct port *port = netdev_priv(dev);
++
++	if (!port->phydev)
++		return -EOPNOTSUPP;
++
+ 	return phy_ethtool_gset(port->phydev, cmd);
+ }
+ 
+ static int ixp4xx_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+ {
+ 	struct port *port = netdev_priv(dev);
++
++	if (!port->phydev)
++		return -EOPNOTSUPP;
++
+ 	return phy_ethtool_sset(port->phydev, cmd);
+ }
+ 
+ static int ixp4xx_nway_reset(struct net_device *dev)
+ {
+ 	struct port *port = netdev_priv(dev);
++
++	if (!port->phydev)
++		return -EOPNOTSUPP;
++
+ 	return phy_start_aneg(port->phydev);
+ }
+ 
diff --git a/target/linux/ixp4xx/patches-2.6.37/295-latch_led_driver.patch b/target/linux/ixp4xx/patches-2.6.37/295-latch_led_driver.patch
new file mode 100644
index 0000000..1dc2690
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/295-latch_led_driver.patch
@@ -0,0 +1,201 @@
+--- a/drivers/leds/Kconfig
++++ b/drivers/leds/Kconfig
+@@ -176,6 +176,13 @@ config LEDS_LP3944
+ 	  To compile this driver as a module, choose M here: the
+ 	  module will be called leds-lp3944.
+ 
++config LEDS_LATCH
++	tristate "LED Support for Memory Latched LEDs"
++	depends on LEDS_CLASS
++	help
++		-- To Do --
++
++
+ config LEDS_CLEVO_MAIL
+ 	tristate "Mail LED on Clevo notebook"
+ 	depends on X86 && SERIO_I8042 && DMI
+--- /dev/null
++++ b/drivers/leds/leds-latch.c
+@@ -0,0 +1,150 @@
++/*
++ * LEDs driver for Memory Latched Devices
++ *
++ * Copyright (C) 2008 Gateworks Corp.
++ * Chris Lang <clang@gateworks.com>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++#include <linux/kernel.h>
++#include <linux/slab.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/leds.h>
++#include <linux/workqueue.h>
++#include <asm/io.h>
++#include <linux/spinlock.h>
++#include <linux/slab.h>
++
++static unsigned int mem_keep = 0xFF;
++static spinlock_t mem_lock;
++static unsigned char *iobase;
++
++struct latch_led_data {
++	struct led_classdev cdev;
++	struct work_struct work;
++	u8 new_level;
++	u8 bit;
++	void (*set_led)(u8 bit, enum led_brightness value);
++};
++
++static void latch_set_led(u8 bit, enum led_brightness value)
++{
++	if (value == LED_OFF)
++		mem_keep |= (0x1 << bit);
++	else
++		mem_keep &= ~(0x1 << bit);
++
++	writeb(mem_keep, iobase);
++}
++
++static void latch_led_set(struct led_classdev *led_cdev,
++	enum led_brightness value)
++{
++	struct latch_led_data *led_dat =
++		container_of(led_cdev, struct latch_led_data, cdev);
++
++	raw_spin_lock(mem_lock);
++
++	led_dat->set_led(led_dat->bit, value);
++
++	raw_spin_unlock(mem_lock);
++}
++
++static int latch_led_probe(struct platform_device *pdev)
++{
++	struct latch_led_platform_data *pdata = pdev->dev.platform_data;
++	struct latch_led *cur_led;
++	struct latch_led_data *leds_data, *led_dat;
++	int i, ret = 0;
++
++	if (!pdata)
++		return -EBUSY;
++
++	leds_data = kzalloc(sizeof(struct latch_led_data) * pdata->num_leds,
++				GFP_KERNEL);
++	if (!leds_data)
++		return -ENOMEM;
++
++	for (i = 0; i < pdata->num_leds; i++) {
++		cur_led = &pdata->leds[i];
++		led_dat = &leds_data[i];
++
++		led_dat->cdev.name = cur_led->name;
++		led_dat->cdev.default_trigger = cur_led->default_trigger;
++		led_dat->cdev.brightness_set = latch_led_set;
++		led_dat->cdev.brightness = LED_OFF;
++		led_dat->bit = cur_led->bit;
++		led_dat->set_led = pdata->set_led ? pdata->set_led : latch_set_led;
++
++		ret = led_classdev_register(&pdev->dev, &led_dat->cdev);
++		if (ret < 0) {
++			goto err;
++		}
++	}
++
++	if (!pdata->set_led) {
++		iobase = ioremap_nocache(pdata->mem, 0x1000);
++		writeb(0xFF, iobase);
++	}
++	platform_set_drvdata(pdev, leds_data);
++
++	return 0;
++
++err:
++	if (i > 0) {
++		for (i = i - 1; i >= 0; i--) {
++			led_classdev_unregister(&leds_data[i].cdev);
++		}
++	}
++
++	kfree(leds_data);
++
++	return ret;
++}
++
++static int __devexit latch_led_remove(struct platform_device *pdev)
++{
++	int i;
++	struct latch_led_platform_data *pdata = pdev->dev.platform_data;
++	struct latch_led_data *leds_data;
++
++	leds_data = platform_get_drvdata(pdev);
++
++	for (i = 0; i < pdata->num_leds; i++) {
++		led_classdev_unregister(&leds_data[i].cdev);
++		cancel_work_sync(&leds_data[i].work);
++	}
++
++	kfree(leds_data);
++
++	return 0;
++}
++
++static struct platform_driver latch_led_driver = {
++	.probe		= latch_led_probe,
++	.remove		= __devexit_p(latch_led_remove),
++	.driver		= {
++		.name	= "leds-latch",
++		.owner	= THIS_MODULE,
++	},
++};
++
++static int __init latch_led_init(void)
++{
++	return platform_driver_register(&latch_led_driver);
++}
++
++static void __exit latch_led_exit(void)
++{
++	platform_driver_unregister(&latch_led_driver);
++}
++
++module_init(latch_led_init);
++module_exit(latch_led_exit);
++
++MODULE_AUTHOR("Chris Lang <clang@gateworks.com>");
++MODULE_DESCRIPTION("Latch LED driver");
+--- a/drivers/leds/Makefile
++++ b/drivers/leds/Makefile
+@@ -22,6 +22,7 @@ obj-$(CONFIG_LEDS_COBALT_RAQ)		+= leds-c
+ obj-$(CONFIG_LEDS_SUNFIRE)		+= leds-sunfire.o
+ obj-$(CONFIG_LEDS_PCA9532)		+= leds-pca9532.o
+ obj-$(CONFIG_LEDS_GPIO)			+= leds-gpio.o
++obj-$(CONFIG_LEDS_LATCH)		+= leds-latch.o
+ obj-$(CONFIG_LEDS_LP3944)		+= leds-lp3944.o
+ obj-$(CONFIG_LEDS_CLEVO_MAIL)		+= leds-clevo-mail.o
+ obj-$(CONFIG_LEDS_HP6XX)		+= leds-hp6xx.o
+--- a/include/linux/leds.h
++++ b/include/linux/leds.h
+@@ -165,5 +165,19 @@ struct gpio_led_platform_data {
+ 					unsigned long *delay_off);
+ };
+ 
++/* For the leds-latch driver */
++struct latch_led {
++	const char *name;
++	char *default_trigger;
++	unsigned  bit;
++};
++
++struct latch_led_platform_data {
++	int     num_leds;
++	u32     mem;
++	struct latch_led *leds;
++	void	(*set_led)(u8 bit, enum led_brightness value);
++};
++
+ 
+ #endif		/* __LINUX_LEDS_H_INCLUDED */
diff --git a/target/linux/ixp4xx/patches-2.6.37/300-avila_fetch_mac.patch b/target/linux/ixp4xx/patches-2.6.37/300-avila_fetch_mac.patch
new file mode 100644
index 0000000..8cbd38d
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/300-avila_fetch_mac.patch
@@ -0,0 +1,242 @@
+--- a/arch/arm/mach-ixp4xx/avila-setup.c
++++ b/arch/arm/mach-ixp4xx/avila-setup.c
+@@ -14,9 +14,14 @@
+ #include <linux/kernel.h>
+ #include <linux/init.h>
+ #include <linux/device.h>
++#include <linux/if_ether.h>
++#include <linux/socket.h>
++#include <linux/netdevice.h>
+ #include <linux/serial.h>
+ #include <linux/tty.h>
+ #include <linux/serial_8250.h>
++#include <linux/i2c.h>
++#include <linux/i2c/at24.h>
+ #include <linux/i2c-gpio.h>
+ #include <asm/types.h>
+ #include <asm/setup.h>
+@@ -30,6 +35,13 @@
+ #define AVILA_SDA_PIN	7
+ #define AVILA_SCL_PIN	6
+ 
++struct avila_board_info {
++	unsigned char	*model;
++	void		(*setup)(void);
++};
++
++static struct avila_board_info *avila_info __initdata;
++
+ static struct flash_platform_data avila_flash_data = {
+ 	.map_name	= "cfi_probe",
+ 	.width		= 2,
+@@ -133,16 +145,181 @@ static struct platform_device avila_pata
+ 	.resource		= avila_pata_resources,
+ };
+ 
++/* Built-in 10/100 Ethernet MAC interfaces */
++static struct eth_plat_info avila_npeb_data = {
++	.phy		= 0,
++	.rxq		= 3,
++	.txreadyq	= 20,
++};
++
++static struct eth_plat_info avila_npec_data = {
++	.phy		= 1,
++	.rxq		= 4,
++	.txreadyq	= 21,
++};
++
++static struct platform_device avila_npeb_device = {
++	.name			= "ixp4xx_eth",
++	.id			= IXP4XX_ETH_NPEB,
++	.dev.platform_data	= &avila_npeb_data,
++};
++
++static struct platform_device avila_npec_device = {
++	.name			= "ixp4xx_eth",
++	.id			= IXP4XX_ETH_NPEC,
++	.dev.platform_data	= &avila_npec_data,
++};
++
+ static struct platform_device *avila_devices[] __initdata = {
+ 	&avila_i2c_gpio,
+ 	&avila_flash,
+ 	&avila_uart
+ };
+ 
++static void __init avila_gw23xx_setup(void)
++{
++	platform_device_register(&avila_npeb_device);
++	platform_device_register(&avila_npec_device);
++}
++
++static void __init avila_gw2342_setup(void)
++{
++	platform_device_register(&avila_npeb_device);
++	platform_device_register(&avila_npec_device);
++}
++
++static void __init avila_gw2345_setup(void)
++{
++	avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR;
++	avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */
++	platform_device_register(&avila_npeb_device);
++
++	avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */
++	platform_device_register(&avila_npec_device);
++}
++
++static void __init avila_gw2347_setup(void)
++{
++	platform_device_register(&avila_npeb_device);
++}
++
++static void __init avila_gw2348_setup(void)
++{
++	platform_device_register(&avila_npeb_device);
++	platform_device_register(&avila_npec_device);
++}
++
++static void __init avila_gw2353_setup(void)
++{
++	platform_device_register(&avila_npeb_device);
++}
++
++static void __init avila_gw2355_setup(void)
++{
++	avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR;
++	avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */
++	platform_device_register(&avila_npeb_device);
++
++	avila_npec_data.phy = 16;
++	platform_device_register(&avila_npec_device);
++}
++
++static void __init avila_gw2357_setup(void)
++{
++	platform_device_register(&avila_npeb_device);
++}
++
++static struct avila_board_info avila_boards[] __initdata = {
++	{
++		.model		= "GW2342",
++		.setup		= avila_gw2342_setup,
++	}, {
++		.model		= "GW2345",
++		.setup		= avila_gw2345_setup,
++	}, {
++		.model		= "GW2347",
++		.setup		= avila_gw2347_setup,
++	}, {
++		.model		= "GW2348",
++		.setup		= avila_gw2348_setup,
++	}, {
++		.model		= "GW2353",
++		.setup		= avila_gw2353_setup,
++	}, {
++		.model		= "GW2355",
++		.setup		= avila_gw2355_setup,
++	}, {
++		.model		= "GW2357",
++		.setup		= avila_gw2357_setup,
++	}
++};
++
++static struct avila_board_info * __init avila_find_board_info(char *model)
++{
++	int i;
++	model[6] = '\0';
++
++	for (i = 0; i < ARRAY_SIZE(avila_boards); i++) {
++		struct avila_board_info *info = &avila_boards[i];
++		if (strcmp(info->model, model) == 0)
++			return info;
++	}
++
++	return NULL;
++}
++
++static struct memory_accessor *at24_mem_acc;
++
++static void at24_setup(struct memory_accessor *mem_acc, void *context)
++{
++	char mac_addr[ETH_ALEN];
++	char model[7];
++
++	at24_mem_acc = mem_acc;
++
++	/* Read MAC addresses */
++	if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x0, 6) == 6) {
++		memcpy(&avila_npeb_data.hwaddr, mac_addr, ETH_ALEN);
++	}
++	if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x6, 6) == 6) {
++		memcpy(&avila_npec_data.hwaddr, mac_addr, ETH_ALEN);
++	}
++
++	/* Read the first 6 bytes of the model number */
++	if (at24_mem_acc->read(at24_mem_acc, model, 0x20, 6) == 6) {
++		avila_info = avila_find_board_info(model);
++	}
++
++}
++
++static struct at24_platform_data avila_eeprom_info = {
++	.byte_len	= 1024,
++	.page_size	= 16,
++	.flags		= AT24_FLAG_READONLY,
++	.setup		= at24_setup,
++};
++
++static struct i2c_board_info __initdata avila_i2c_board_info[] = {
++	{
++		I2C_BOARD_INFO("ds1672", 0x68),
++	},
++	{
++		I2C_BOARD_INFO("ad7418", 0x28),
++	},
++	{
++		I2C_BOARD_INFO("24c08", 0x51),
++		.platform_data	= &avila_eeprom_info
++	},
++};
++
+ static void __init avila_init(void)
+ {
+ 	ixp4xx_sys_init();
+ 
++	/*
++	 * These devices are present on all Avila models and don't need any
++	 * model specific setup.
++	 */
+ 	avila_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ 	avila_flash_resource.end =
+ 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+@@ -160,7 +337,28 @@ static void __init avila_init(void)
+ 
+ 	platform_device_register(&avila_pata);
+ 
++		i2c_register_board_info(0, avila_i2c_board_info,
++				ARRAY_SIZE(avila_i2c_board_info));
++}
++
++static int __init avila_model_setup(void)
++{
++	if (!machine_is_avila())
++		return 0;
++
++	if (avila_info) {
++		printk(KERN_DEBUG "Running on Gateworks Avila %s\n",
++							avila_info->model);
++		avila_info->setup();
++	} else {
++		printk(KERN_INFO "Unknown/missing Avila model number"
++						" -- defaults will be used\n");
++		avila_gw23xx_setup();
++	}
++
++	return 0;
+ }
++late_initcall(avila_model_setup);
+ 
+ MACHINE_START(AVILA, "Gateworks Avila Network Platform")
+ 	/* Maintainer: Deepak Saxena <dsaxena@plexity.net> */
diff --git a/target/linux/ixp4xx/patches-2.6.37/301-avila_led.patch b/target/linux/ixp4xx/patches-2.6.37/301-avila_led.patch
new file mode 100644
index 0000000..9acf3fd
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/301-avila_led.patch
@@ -0,0 +1,161 @@
+--- a/arch/arm/mach-ixp4xx/avila-setup.c
++++ b/arch/arm/mach-ixp4xx/avila-setup.c
+@@ -22,6 +22,7 @@
+ #include <linux/serial_8250.h>
+ #include <linux/i2c.h>
+ #include <linux/i2c/at24.h>
++#include <linux/leds.h>
+ #include <linux/i2c-gpio.h>
+ #include <asm/types.h>
+ #include <asm/setup.h>
+@@ -170,6 +171,72 @@ static struct platform_device avila_npec
+ 	.dev.platform_data	= &avila_npec_data,
+ };
+ 
++static struct gpio_led avila_gpio_leds[] = {
++	{
++		.name		= "user",  /* green led */
++		.gpio		= AVILA_GW23XX_LED_USER_GPIO,
++		.active_low	= 1,
++	}
++};
++
++static struct gpio_led_platform_data avila_gpio_leds_data = {
++	.num_leds		= 1,
++	.leds			= avila_gpio_leds,
++};
++
++static struct platform_device avila_gpio_leds_device = {
++	.name			= "leds-gpio",
++	.id			= -1,
++	.dev.platform_data	= &avila_gpio_leds_data,
++};
++
++static struct latch_led avila_latch_leds[] = {
++	{
++		.name	= "led0",  /* green led */
++		.bit	= 0,
++	},
++	{
++		.name	= "led1",  /* green led */
++		.bit	= 1,
++	},
++	{
++		.name	= "led2",  /* green led */
++		.bit	= 2,
++	},
++	{
++		.name	= "led3",  /* green led */
++		.bit	= 3,
++	},
++	{
++		.name	= "led4",  /* green led */
++		.bit	= 4,
++	},
++	{
++		.name	= "led5",  /* green led */
++		.bit	= 5,
++	},
++	{
++		.name	= "led6",  /* green led */
++		.bit	= 6,
++	},
++	{
++		.name	= "led7",  /* green led */
++		.bit	= 7,
++	}
++};
++
++static struct latch_led_platform_data avila_latch_leds_data = {
++	.num_leds	= 8,
++	.leds		= avila_latch_leds,
++	.mem		= 0x51000000,
++};
++
++static struct platform_device avila_latch_leds_device = {
++	.name			= "leds-latch",
++	.id			= -1,
++	.dev.platform_data	= &avila_latch_leds_data,
++};
++
+ static struct platform_device *avila_devices[] __initdata = {
+ 	&avila_i2c_gpio,
+ 	&avila_flash,
+@@ -180,12 +247,16 @@ static void __init avila_gw23xx_setup(vo
+ {
+ 	platform_device_register(&avila_npeb_device);
+ 	platform_device_register(&avila_npec_device);
++
++	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2342_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
+ 	platform_device_register(&avila_npec_device);
++
++	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2345_setup(void)
+@@ -196,22 +267,30 @@ static void __init avila_gw2345_setup(vo
+ 
+ 	avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */
+ 	platform_device_register(&avila_npec_device);
++
++	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2347_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
++
++	avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
++	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2348_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
+ 	platform_device_register(&avila_npec_device);
++
++	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2353_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
++	platform_device_register(&avila_gpio_leds_device);
+ }
+ 
+ static void __init avila_gw2355_setup(void)
+@@ -222,11 +301,29 @@ static void __init avila_gw2355_setup(vo
+ 
+ 	avila_npec_data.phy = 16;
+ 	platform_device_register(&avila_npec_device);
++
++	platform_device_register(&avila_gpio_leds_device);
++
++	*IXP4XX_EXP_CS4 |= 0xbfff3c03;
++	avila_latch_leds[0].name = "RXD";
++	avila_latch_leds[1].name = "TXD";
++	avila_latch_leds[2].name = "POL";
++	avila_latch_leds[3].name = "LNK";
++	avila_latch_leds[4].name = "ERR";
++	avila_latch_leds_data.num_leds = 5;
++	avila_latch_leds_data.mem = 0x54000000;
++	platform_device_register(&avila_latch_leds_device);
+ }
+ 
+ static void __init avila_gw2357_setup(void)
+ {
+ 	platform_device_register(&avila_npeb_device);
++
++	avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
++	platform_device_register(&avila_gpio_leds_device);
++
++	*IXP4XX_EXP_CS1 |= 0xbfff3c03;
++	platform_device_register(&avila_latch_leds_device);
+ }
+ 
+ static struct avila_board_info avila_boards[] __initdata = {
diff --git a/target/linux/ixp4xx/patches-2.6.37/302-avila_gpio_device.patch b/target/linux/ixp4xx/patches-2.6.37/302-avila_gpio_device.patch
new file mode 100644
index 0000000..a45d432
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/302-avila_gpio_device.patch
@@ -0,0 +1,16 @@
+--- a/arch/arm/mach-ixp4xx/avila-setup.c
++++ b/arch/arm/mach-ixp4xx/avila-setup.c
+@@ -36,6 +36,13 @@
+ #define AVILA_SDA_PIN	7
+ #define AVILA_SCL_PIN	6
+ 
++/* User LEDs */
++#define AVILA_GW23XX_LED_USER_GPIO     3
++#define AVILA_GW23X7_LED_USER_GPIO     4
++
++/* gpio mask used by platform device */
++#define AVILA_GPIO_MASK        (1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) | (1 << 9)
++
+ struct avila_board_info {
+ 	unsigned char	*model;
+ 	void		(*setup)(void);
diff --git a/target/linux/ixp4xx/patches-2.6.37/304-ixp4xx_eth_jumboframe.patch b/target/linux/ixp4xx/patches-2.6.37/304-ixp4xx_eth_jumboframe.patch
new file mode 100644
index 0000000..9da18e7
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/304-ixp4xx_eth_jumboframe.patch
@@ -0,0 +1,80 @@
+--- a/drivers/net/arm/ixp4xx_eth.c
++++ b/drivers/net/arm/ixp4xx_eth.c
+@@ -53,7 +53,7 @@
+ 
+ #define POOL_ALLOC_SIZE		(sizeof(struct desc) * (RX_DESCS + TX_DESCS))
+ #define REGS_SIZE		0x1000
+-#define MAX_MRU			1536 /* 0x600 */
++#define MAX_MRU			(14320 - ETH_HLEN - ETH_FCS_LEN)
+ #define RX_BUFF_SIZE		ALIGN((NET_IP_ALIGN) + MAX_MRU, 4)
+ 
+ #define NAPI_WEIGHT		16
+@@ -1075,6 +1075,32 @@ static void destroy_queues(struct port *
+ 	}
+ }
+ 
++static int eth_do_change_mtu(struct net_device *dev, int mtu)
++{
++	struct port *port;
++	struct msg msg;
++	/* adjust for ethernet headers */
++	int framesize = mtu + ETH_HLEN + ETH_FCS_LEN;
++
++	port = netdev_priv(dev);
++
++	memset(&msg, 0, sizeof(msg));
++	msg.cmd = NPE_SETMAXFRAMELENGTHS;
++	msg.eth_id = port->id;
++
++	/* max rx/tx 64 byte blocks */
++	msg.byte2 = ((framesize + 63) / 64) << 8;
++	msg.byte3 = ((framesize + 63) / 64) << 8;
++
++	msg.byte4 = msg.byte6 = framesize >> 8;
++	msg.byte5 = msg.byte7 = framesize & 0xff;
++
++	if (npe_send_recv_message(port->npe, &msg, "ETH_SET_MAX_FRAME_LENGTH"))
++		return -EIO;
++
++	return 0;
++}
++
+ static int eth_open(struct net_device *dev)
+ {
+ 	struct port *port = netdev_priv(dev);
+@@ -1126,6 +1152,8 @@ static int eth_open(struct net_device *d
+ 	if (npe_send_recv_message(port->npe, &msg, "ETH_SET_FIREWALL_MODE"))
+ 		return -EIO;
+ 
++	eth_do_change_mtu(dev, dev->mtu);
++
+ 	if ((err = request_queues(port)) != 0)
+ 		return err;
+ 
+@@ -1265,7 +1293,26 @@ static int eth_close(struct net_device *
+ 	return 0;
+ }
+ 
++static int ixp_eth_change_mtu(struct net_device *dev, int mtu)
++{
++	int ret;
++
++	if (mtu > MAX_MRU)
++		return -EINVAL;
++
++	if (dev->flags & IFF_UP) {
++		ret = eth_do_change_mtu(dev, mtu);
++		if (ret < 0)
++			return ret;
++	}
++
++	dev->mtu = mtu;
++
++	return 0;
++}
++
+ static const struct net_device_ops ixp4xx_netdev_ops = {
++	.ndo_change_mtu = ixp_eth_change_mtu,
+ 	.ndo_open = eth_open,
+ 	.ndo_stop = eth_close,
+ 	.ndo_start_xmit = eth_xmit,
diff --git a/target/linux/ixp4xx/patches-2.6.37/310-gtwx5717_spi_bus.patch b/target/linux/ixp4xx/patches-2.6.37/310-gtwx5717_spi_bus.patch
new file mode 100644
index 0000000..080b96a
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/310-gtwx5717_spi_bus.patch
@@ -0,0 +1,52 @@
+--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
++++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+@@ -27,6 +27,7 @@
+ #include <linux/serial.h>
+ #include <linux/tty.h>
+ #include <linux/serial_8250.h>
++#include <linux/spi/spi_gpio_old.h>
+ #include <asm/types.h>
+ #include <asm/setup.h>
+ #include <asm/memory.h>
+@@ -146,9 +147,41 @@ static struct platform_device gtwx5715_f
+ 	.resource	= &gtwx5715_flash_resource,
+ };
+ 
++static int gtwx5715_spi_boardinfo_setup(struct spi_board_info *bi,
++		struct spi_master *master, void *data)
++{
++
++	strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias));
++
++	bi->max_speed_hz = 5000000 /* Hz */;
++	bi->bus_num = master->bus_num;
++	bi->mode = SPI_MODE_0;
++
++	return 0;
++}
++
++static struct spi_gpio_platform_data gtwx5715_spi_bus_data = {
++	.pin_cs			= GTWX5715_KSSPI_SELECT,
++	.pin_clk		= GTWX5715_KSSPI_CLOCK,
++	.pin_miso		= GTWX5715_KSSPI_RXD,
++	.pin_mosi		= GTWX5715_KSSPI_TXD,
++	.cs_activelow		= 1,
++	.no_spi_delay		= 1,
++	.boardinfo_setup	= gtwx5715_spi_boardinfo_setup,
++};
++
++static struct platform_device gtwx5715_spi_bus = {
++	.name		= "spi-gpio",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &gtwx5715_spi_bus_data,
++	},
++};
++
+ static struct platform_device *gtwx5715_devices[] __initdata = {
+ 	&gtwx5715_uart_device,
+ 	&gtwx5715_flash,
++	&gtwx5715_spi_bus,
+ };
+ 
+ static void __init gtwx5715_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.37/311-gtwx5717_mac_plat_info.patch b/target/linux/ixp4xx/patches-2.6.37/311-gtwx5717_mac_plat_info.patch
new file mode 100644
index 0000000..706eed2
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/311-gtwx5717_mac_plat_info.patch
@@ -0,0 +1,40 @@
+--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
++++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+@@ -178,10 +178,37 @@ static struct platform_device gtwx5715_s
+ 	},
+ };
+ 
++static struct eth_plat_info gtwx5715_npeb_data = {
++	.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
++	.phy_mask	= 0x1e, /* ports 1-4 of the KS8995 switch */
++	.rxq		= 3,
++	.txreadyq	= 20,
++};
++
++static struct eth_plat_info gtwx5715_npec_data = {
++	.phy		= 5,	/* port 5 of the KS8995 switch */
++	.rxq		= 4,
++	.txreadyq	= 21,
++};
++
++static struct platform_device gtwx5715_npeb_device = {
++	.name			= "ixp4xx_eth",
++	.id			= IXP4XX_ETH_NPEB,
++	.dev.platform_data	= &gtwx5715_npeb_data,
++};
++
++static struct platform_device gtwx5715_npec_device = {
++	.name			= "ixp4xx_eth",
++	.id			= IXP4XX_ETH_NPEC,
++	.dev.platform_data	= &gtwx5715_npec_data,
++};
++
+ static struct platform_device *gtwx5715_devices[] __initdata = {
+ 	&gtwx5715_uart_device,
+ 	&gtwx5715_flash,
+ 	&gtwx5715_spi_bus,
++	&gtwx5715_npeb_device,
++	&gtwx5715_npec_device,
+ };
+ 
+ static void __init gtwx5715_init(void)
diff --git a/target/linux/ixp4xx/patches-2.6.37/312-ixp4xx_pata_optimization.patch b/target/linux/ixp4xx/patches-2.6.37/312-ixp4xx_pata_optimization.patch
new file mode 100644
index 0000000..3bf1b74
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/312-ixp4xx_pata_optimization.patch
@@ -0,0 +1,137 @@
+--- a/drivers/ata/pata_ixp4xx_cf.c
++++ b/drivers/ata/pata_ixp4xx_cf.c
+@@ -24,16 +24,58 @@
+ #include <scsi/scsi_host.h>
+ 
+ #define DRV_NAME	"pata_ixp4xx_cf"
+-#define DRV_VERSION	"0.2"
++#define DRV_VERSION	"0.3"
+ 
+ static int ixp4xx_set_mode(struct ata_link *link, struct ata_device **error)
+ {
+ 	struct ata_device *dev;
++	struct ixp4xx_pata_data *data = link->ap->host->dev->platform_data;
++	unsigned int pio_mask;
+ 
+ 	ata_for_each_dev(dev, link, ENABLED) {
+-		ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
+-		dev->pio_mode = XFER_PIO_0;
+-		dev->xfer_mode = XFER_PIO_0;
++		if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)) {
++			pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03;
++			if (pio_mask & (1 << 1)) {
++				pio_mask = 4;
++			} else {
++				pio_mask = 3;
++			}
++		} else {
++			pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8);
++		}
++
++		switch (pio_mask){
++			case 0:
++				ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
++				dev->pio_mode = XFER_PIO_0;
++				dev->xfer_mode = XFER_PIO_0;
++				*data->cs0_cfg = 0x8a473c03;
++				break;
++			case 1:
++				ata_dev_printk(dev, KERN_INFO, "configured for PIO1\n");
++				dev->pio_mode = XFER_PIO_1;
++				dev->xfer_mode = XFER_PIO_1;
++				*data->cs0_cfg = 0x86433c03;
++				break;
++			case 2:
++				ata_dev_printk(dev, KERN_INFO, "configured for PIO2\n");
++				dev->pio_mode = XFER_PIO_2;
++				dev->xfer_mode = XFER_PIO_2;
++				*data->cs0_cfg = 0x82413c03;
++				break;
++			case 3:
++				ata_dev_printk(dev, KERN_INFO, "configured for PIO3\n");
++				dev->pio_mode = XFER_PIO_3;
++				dev->xfer_mode = XFER_PIO_3;
++				*data->cs0_cfg = 0x80823c03;
++				break;
++			case 4:
++				ata_dev_printk(dev, KERN_INFO, "configured for PIO4\n");
++				dev->pio_mode = XFER_PIO_4;
++				dev->xfer_mode = XFER_PIO_4;
++				*data->cs0_cfg = 0x80403c03;
++				break;
++		}
+ 		dev->xfer_shift = ATA_SHIFT_PIO;
+ 		dev->flags |= ATA_DFLAG_PIO;
+ 	}
+@@ -46,6 +88,7 @@ static unsigned int ixp4xx_mmio_data_xfe
+ 	unsigned int i;
+ 	unsigned int words = buflen >> 1;
+ 	u16 *buf16 = (u16 *) buf;
++	unsigned int pio_mask;
+ 	struct ata_port *ap = dev->link->ap;
+ 	void __iomem *mmio = ap->ioaddr.data_addr;
+ 	struct ixp4xx_pata_data *data = ap->host->dev->platform_data;
+@@ -53,8 +96,34 @@ static unsigned int ixp4xx_mmio_data_xfe
+ 	/* set the expansion bus in 16bit mode and restore
+ 	 * 8 bit mode after the transaction.
+ 	 */
+-	*data->cs0_cfg &= ~(0x01);
+-	udelay(100);
++	if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)){
++		pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03;
++		if (pio_mask & (1 << 1)){
++			pio_mask = 4;
++		}else{
++			pio_mask = 3;
++		}
++	}else{
++		pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8);
++	}
++	switch (pio_mask){
++		case 0:
++			*data->cs0_cfg = 0xa9643c42;
++		break;
++		case 1:
++			*data->cs0_cfg = 0x85033c42;
++		break;
++		case 2:
++			*data->cs0_cfg = 0x80b23c42;
++		break;
++		case 3:
++			*data->cs0_cfg = 0x80823c42;
++		break;
++		case 4:
++			*data->cs0_cfg = 0x80403c42;
++		break;
++	}
++	udelay(5);
+ 
+ 	/* Transfer multiple of 2 bytes */
+ 	if (rw == READ)
+@@ -79,8 +148,24 @@ static unsigned int ixp4xx_mmio_data_xfe
+ 		words++;
+ 	}
+ 
+-	udelay(100);
+-	*data->cs0_cfg |= 0x01;
++	udelay(5);
++	switch (pio_mask){
++		case 0:
++			*data->cs0_cfg = 0x8a473c03;
++		break;
++		case 1:
++			*data->cs0_cfg = 0x86433c03;
++		break;
++		case 2:
++			*data->cs0_cfg = 0x82413c03;
++		break;
++		case 3:
++			*data->cs0_cfg = 0x80823c03;
++		break;
++		case 4:
++			*data->cs0_cfg = 0x80403c03;
++		break;
++	}
+ 
+ 	return words << 1;
+ }
diff --git a/target/linux/ixp4xx/patches-2.6.37/402-ixp4xx_gpiolib.patch b/target/linux/ixp4xx/patches-2.6.37/402-ixp4xx_gpiolib.patch
new file mode 100644
index 0000000..f8e9df5
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/402-ixp4xx_gpiolib.patch
@@ -0,0 +1,137 @@
+--- a/arch/arm/mach-ixp4xx/common.c
++++ b/arch/arm/mach-ixp4xx/common.c
+@@ -35,6 +35,7 @@
+ #include <asm/pgtable.h>
+ #include <asm/page.h>
+ #include <asm/irq.h>
++#include <asm/gpio.h>
+ 
+ #include <asm/mach/map.h>
+ #include <asm/mach/irq.h>
+@@ -374,12 +375,50 @@ static struct platform_device *ixp46x_de
+ unsigned long ixp4xx_exp_bus_size;
+ EXPORT_SYMBOL(ixp4xx_exp_bus_size);
+ 
++static int ixp4xx_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
++{
++	gpio_line_config(gpio, IXP4XX_GPIO_IN);
++	return 0;
++}
++
++static int ixp4xx_gpio_direction_output(struct gpio_chip *chip, unsigned gpio, int level)
++{
++	gpio_line_set(gpio, level);
++	gpio_line_config(gpio, IXP4XX_GPIO_OUT);
++	return 0;
++}
++
++static int ixp4xx_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
++{
++	int value;
++
++	gpio_line_get(gpio, &value);
++	return value;
++}
++
++static void ixp4xx_gpio_set_value(struct gpio_chip *chip, unsigned gpio, int value)
++{
++	gpio_line_set(gpio, value);
++}
++
++static struct gpio_chip ixp4xx_gpio_chip = {
++	.label			= "IXP4XX_GPIO_CHIP",
++	.direction_input	= ixp4xx_gpio_direction_input,
++	.direction_output	= ixp4xx_gpio_direction_output,
++	.get			= ixp4xx_gpio_get_value,
++	.set			= ixp4xx_gpio_set_value,
++	.base			= 0,
++	.ngpio			= 16,
++};
++
+ void __init ixp4xx_sys_init(void)
+ {
+ 	ixp4xx_exp_bus_size = SZ_16M;
+ 
+ 	platform_add_devices(ixp4xx_devices, ARRAY_SIZE(ixp4xx_devices));
+ 
++	gpiochip_add(&ixp4xx_gpio_chip);
++
+ 	if (cpu_is_ixp46x()) {
+ 		int region;
+ 
+--- a/arch/arm/Kconfig
++++ b/arch/arm/Kconfig
+@@ -431,7 +431,7 @@ config ARCH_IXP4XX
+ 	bool "IXP4xx-based"
+ 	depends on MMU
+ 	select CPU_XSCALE
+-	select GENERIC_GPIO
++	select ARCH_REQUIRE_GPIOLIB
+ 	select GENERIC_CLOCKEVENTS
+ 	select DMABOUNCE if PCI
+ 	help
+--- a/arch/arm/mach-ixp4xx/include/mach/gpio.h
++++ b/arch/arm/mach-ixp4xx/include/mach/gpio.h
+@@ -27,47 +27,31 @@
+ 
+ #include <linux/kernel.h>
+ #include <mach/hardware.h>
++#include <asm-generic/gpio.h>			/* cansleep wrappers */
+ 
+-static inline int gpio_request(unsigned gpio, const char *label)
+-{
+-	return 0;
+-}
+-
+-static inline void gpio_free(unsigned gpio)
+-{
+-	might_sleep();
+-
+-	return;
+-}
+-
+-static inline int gpio_direction_input(unsigned gpio)
+-{
+-	gpio_line_config(gpio, IXP4XX_GPIO_IN);
+-	return 0;
+-}
+-
+-static inline int gpio_direction_output(unsigned gpio, int level)
+-{
+-	gpio_line_set(gpio, level);
+-	gpio_line_config(gpio, IXP4XX_GPIO_OUT);
+-	return 0;
+-}
++#define NR_BUILTIN_GPIO 16
+ 
+ static inline int gpio_get_value(unsigned gpio)
+ {
+-	int value;
+-
+-	gpio_line_get(gpio, &value);
+-
+-	return value;
++	if (gpio < NR_BUILTIN_GPIO)
++	{
++		int value;
++		gpio_line_get(gpio, &value);
++		return value;
++	}
++	else
++		return __gpio_get_value(gpio);
+ }
+ 
+ static inline void gpio_set_value(unsigned gpio, int value)
+ {
+-	gpio_line_set(gpio, value);
++	if (gpio < NR_BUILTIN_GPIO)
++		gpio_line_set(gpio, value);
++	else
++		__gpio_set_value(gpio, value);
+ }
+ 
+-#include <asm-generic/gpio.h>			/* cansleep wrappers */
++#define gpio_cansleep __gpio_cansleep
+ 
+ extern int gpio_to_irq(int gpio);
+ extern int irq_to_gpio(unsigned int irq);
diff --git a/target/linux/ixp4xx/patches-2.6.37/500-usr8200_support.patch b/target/linux/ixp4xx/patches-2.6.37/500-usr8200_support.patch
new file mode 100644
index 0000000..e757ff3
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/500-usr8200_support.patch
@@ -0,0 +1,342 @@
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -97,6 +97,14 @@ config MACH_SIDEWINDER
+ 	  Engineering Sidewinder board. For more information on this
+ 	  platform, see http://www.adiengineering.com
+ 
++config MACH_USR8200
++	bool "USRobotics USR8200"
++	select PCI
++	help
++	  Say 'Y' here if you want your kernel to support the USRobotics
++	  USR8200 router board. For more information on this platform, see
++	  http://openwrt.org
++
+ config MACH_COMPEX
+ 	bool "Compex WP18 / NP18A"
+ 	select PCI
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -26,6 +26,7 @@ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt
+ obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_TW5334)		+= tw5334-pci.o
+ obj-pci-$(CONFIG_MACH_MI424WR)		+= mi424wr-pci.o
++obj-pci-$(CONFIG_MACH_USR8200)		+= usr8200-pci.o
+ 
+ obj-y	+= common.o
+ 
+@@ -51,6 +52,7 @@ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv
+ obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
+ obj-$(CONFIG_MACH_TW5334)	+= tw5334-setup.o
+ obj-$(CONFIG_MACH_MI424WR)	+= mi424wr-setup.o
++obj-$(CONFIG_MACH_USR8200)	+= usr8200-setup.o
+ 
+ obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)	+= ixp4xx_qmgr.o
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/usr8200-pci.c
+@@ -0,0 +1,78 @@
++/*
++ * arch/arch/mach-ixp4xx/usr8200-pci.c
++ *
++ * PCI setup routines for USRobotics USR8200
++ *
++ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org>
++ *
++ * based on pronghorn-pci.c
++ * 	Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ * based on coyote-pci.c:
++ *	Copyright (C) 2002 Jungo Software Technologies.
++ *	Copyright (C) 2003 MontaVista Softwrae, Inc.
++ *
++ * Maintainer: Peter Denison <openwrt@marshadder.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++
++#include <asm/mach/pci.h>
++
++void __init usr8200_pci_preinit(void)
++{
++	set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
++
++	ixp4xx_pci_preinit();
++}
++
++static int __init usr8200_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == 14)
++		return IRQ_IXP4XX_GPIO7;
++	else if (slot == 15)
++		return IRQ_IXP4XX_GPIO8;
++	else if (slot == 16) {
++		if (pin == 1)
++			return IRQ_IXP4XX_GPIO11;
++		else if (pin == 2)
++			return IRQ_IXP4XX_GPIO10;
++		else if (pin == 3)
++			return IRQ_IXP4XX_GPIO9;
++		else
++			return -1;
++	} else
++		return -1;
++}
++
++struct hw_pci usr8200_pci __initdata = {
++	.nr_controllers	= 1,
++	.preinit	= usr8200_pci_preinit,
++	.swizzle	= pci_std_swizzle,
++	.setup		= ixp4xx_setup,
++	.scan		= ixp4xx_scan_bus,
++	.map_irq	= usr8200_map_irq,
++};
++
++int __init usr8200_pci_init(void)
++{
++	if (machine_is_usr8200())
++		pci_common_init(&usr8200_pci);
++	return 0;
++}
++
++subsys_initcall(usr8200_pci_init);
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/usr8200-setup.c
+@@ -0,0 +1,212 @@
++/*
++ * arch/arm/mach-ixp4xx/usr8200-setup.c
++ *
++ * Board setup for the USRobotics USR8200
++ *
++ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org>
++ *
++ * based on pronghorn-setup.c:
++ * 	Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Peter Denison <openwrt@marshadder.org>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++#include <linux/types.h>
++#include <linux/memory.h>
++#include <linux/i2c-gpio.h>
++#include <linux/leds.h>
++
++#include <asm/setup.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data usr8200_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource usr8200_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device usr8200_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data	= &usr8200_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &usr8200_flash_resource,
++};
++
++static struct resource usr8200_uart_resources [] = {
++	{
++		.start		= IXP4XX_UART2_BASE_PHYS,
++		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	},
++	{
++		.start		= IXP4XX_UART1_BASE_PHYS,
++		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	}
++};
++
++static struct plat_serial8250_port usr8200_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device usr8200_uart = {
++	.name		= "serial8250",
++	.id		= PLAT8250_DEV_PLATFORM,
++	.dev		= {
++		.platform_data	= usr8200_uart_data,
++	},
++	.num_resources	= 2,
++	.resource	= usr8200_uart_resources,
++};
++
++static struct gpio_led usr8200_led_pin[] = {
++	{
++		.name		= "usr8200:usb1",
++		.gpio		= 0,
++		.active_low	= 1,
++	},
++	{
++		.name		= "usr8200:usb2",
++		.gpio		= 1,
++		.active_low	= 1,
++	},
++	{
++		.name		= "usr8200:ieee1394",
++		.gpio		= 2,
++		.active_low	= 1,
++	},
++	{
++		.name		= "usr8200:internal",
++		.gpio		= 3,
++		.active_low	= 1,
++	},
++	{
++		.name		= "usr8200:power",
++		.gpio		= 14,
++	}
++};
++
++static struct gpio_led_platform_data usr8200_led_data = {
++	.num_leds		= ARRAY_SIZE(usr8200_led_pin),
++	.leds			= usr8200_led_pin,
++};
++
++static struct platform_device usr8200_led = {
++	.name			= "leds-gpio",
++	.id			= -1,
++	.dev.platform_data	= &usr8200_led_data,
++};
++
++static struct eth_plat_info usr8200_plat_eth[] = {
++	{ /* NPEC - LAN with Marvell 88E6060 switch */
++		.phy		= IXP4XX_ETH_PHY_MAX_ADDR,
++		.phy_mask	= 0x0F0000,
++		.rxq		= 4,
++		.txreadyq	= 21,
++	}, { /* NPEB - WAN */
++		.phy		= 9,
++		.rxq		= 3,
++		.txreadyq	= 20,
++	}
++};
++
++static struct platform_device usr8200_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= usr8200_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= usr8200_plat_eth + 1,
++	}
++};
++
++static struct resource usr8200_rtc_resources = {
++	.flags		= IORESOURCE_MEM
++};
++
++static struct platform_device usr8200_rtc = {
++	.name		= "rtc7301",
++	.id		= 0,
++	.num_resources	= 1,
++	.resource	= &usr8200_rtc_resources,
++};
++
++static struct platform_device *usr8200_devices[] __initdata = {
++	&usr8200_flash,
++	&usr8200_uart,
++	&usr8200_led,
++	&usr8200_eth[0],
++	&usr8200_eth[1],
++	&usr8200_rtc,
++};
++
++static void __init usr8200_init(void)
++{
++	ixp4xx_sys_init();
++
++	usr8200_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	usr8200_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1;
++
++	usr8200_rtc_resources.start = IXP4XX_EXP_BUS_BASE(2);
++	usr8200_rtc_resources.end = IXP4XX_EXP_BUS_BASE(2) + 0x01ff;
++
++	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++	*IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN |
++	                  IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN;
++	*IXP4XX_GPIO_GPCLKR = 0x01100000;
++
++	/* configure button as input */
++	gpio_line_config(12, IXP4XX_GPIO_IN);
++
++	platform_add_devices(usr8200_devices, ARRAY_SIZE(usr8200_devices));
++}
++
++MACHINE_START(USR8200, "USRobotics USR8200")
++	/* Maintainer: Peter Denison <openwrt@marshadder.org> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= usr8200_init,
++MACHINE_END
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -43,7 +43,7 @@ static __inline__ void __arch_decomp_set
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+ 			 machine_is_gateway7001() || machine_is_wg302v2() ||
+ 			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+-			 machine_is_tw5334())
++			 machine_is_tw5334() || machine_is_usr8200())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
diff --git a/target/linux/ixp4xx/patches-2.6.37/520-tw2662_support.patch b/target/linux/ixp4xx/patches-2.6.37/520-tw2662_support.patch
new file mode 100644
index 0000000..3fde579
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/520-tw2662_support.patch
@@ -0,0 +1,333 @@
+--- a/arch/arm/mach-ixp4xx/Kconfig
++++ b/arch/arm/mach-ixp4xx/Kconfig
+@@ -180,6 +180,15 @@ config ARCH_PRPMC1100
+ 	  PrPCM1100 Processor Mezanine Module. For more information on
+ 	  this platform, see <file:Documentation/arm/IXP4xx>.
+ 
++config MACH_TW2662
++        bool "Titan Wireless TW-266-2"
++        select PCI
++        help
++          Say 'Y' here if you want your kernel to support the Titan
++          Wireless TW266-2. For more information on this platform,
++          see http://openwrt.org
++
++
+ config MACH_TW5334
+ 	bool "Titan Wireless TW-533-4"
+ 	select PCI
+--- a/arch/arm/mach-ixp4xx/Makefile
++++ b/arch/arm/mach-ixp4xx/Makefile
+@@ -24,6 +24,7 @@ obj-pci-$(CONFIG_MACH_SIDEWINDER)	+= sid
+ obj-pci-$(CONFIG_MACH_COMPEX)		+= ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_WRT300NV2)		+= wrt300nv2-pci.o
+ obj-pci-$(CONFIG_MACH_AP1000)		+= ixdp425-pci.o
++obj-pci-$(CONFIG_MACH_TW2662)		+= tw2662-pci.o
+ obj-pci-$(CONFIG_MACH_TW5334)		+= tw5334-pci.o
+ obj-pci-$(CONFIG_MACH_MI424WR)		+= mi424wr-pci.o
+ obj-pci-$(CONFIG_MACH_USR8200)		+= usr8200-pci.o
+@@ -50,6 +51,7 @@ obj-$(CONFIG_MACH_SIDEWINDER)	+= sidewin
+ obj-$(CONFIG_MACH_COMPEX)	+= compex-setup.o
+ obj-$(CONFIG_MACH_WRT300NV2)	+= wrt300nv2-setup.o
+ obj-$(CONFIG_MACH_AP1000)	+= ap1000-setup.o
++obj-$(CONFIG_MACH_TW2662)	+= tw2662-setup.o
+ obj-$(CONFIG_MACH_TW5334)	+= tw5334-setup.o
+ obj-$(CONFIG_MACH_MI424WR)	+= mi424wr-setup.o
+ obj-$(CONFIG_MACH_USR8200)	+= usr8200-setup.o
+--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+@@ -43,7 +43,7 @@ static __inline__ void __arch_decomp_set
+ 	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+ 			 machine_is_gateway7001() || machine_is_wg302v2() ||
+ 			 machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+-			 machine_is_tw5334() || machine_is_usr8200())
++			 machine_is_tw5334() || machine_is_usr8200() || machine_is_tw2662())
+ 		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+ 	else
+ 		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/tw2662-pci.c
+@@ -0,0 +1,68 @@
++/*
++ * arch/arm/mach-ixp4xx/tw2662-pci.c
++ *
++ * PCI setup routines for Tiran Wireless TW-266-2 platform
++ *
++ * Copyright (C) 2002 Jungo Software Technologies.
++ * Copyright (C) 2003 MontaVista Softwrae, Inc.
++ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com>
++ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
++ *
++ * Maintainer: Deepak Saxena <dsaxena@mvista.com>
++ * Maintainer: Alexandros C. Couloumbis <alex@ozo.com>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++#include <asm/mach-types.h>
++#include <mach/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach/pci.h>
++
++#define SLOT0_DEVID	1
++#define SLOT1_DEVID	3
++
++/* PCI controller GPIO to IRQ pin mappings */
++#define SLOT0_INTA	11
++#define SLOT1_INTA	9
++
++void __init tw2662_pci_preinit(void)
++{
++	set_irq_type(IXP4XX_GPIO_IRQ(SLOT0_INTA), IRQ_TYPE_LEVEL_LOW);
++	set_irq_type(IXP4XX_GPIO_IRQ(SLOT1_INTA), IRQ_TYPE_LEVEL_LOW);
++	ixp4xx_pci_preinit();
++}
++
++static int __init tw2662_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	if (slot == SLOT0_DEVID)
++		return IXP4XX_GPIO_IRQ(SLOT0_INTA);
++	else if (slot == SLOT1_DEVID)
++		return IXP4XX_GPIO_IRQ(SLOT1_INTA);
++	else return -1;
++}
++
++struct hw_pci tw2662_pci __initdata = {
++	.nr_controllers = 1,
++	.preinit =        tw2662_pci_preinit,
++	.swizzle =        pci_std_swizzle,
++	.setup =          ixp4xx_setup,
++	.scan =           ixp4xx_scan_bus,
++	.map_irq =        tw2662_map_irq,
++};
++
++int __init tw2662_pci_init(void)
++{
++        if (machine_is_tw2662())
++		pci_common_init(&tw2662_pci);
++        return 0;
++}
++
++subsys_initcall(tw2662_pci_init);
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/tw2662-setup.c
+@@ -0,0 +1,212 @@
++/*
++ * arch/arm/mach-ixp4xx/tw2662-setup.c
++ *
++ * Titan Wireless TW-266-2
++ *
++ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
++ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com>
++ *
++ * based on ap1000-setup.c:
++ * 	Author: Imre Kaloz <Kaloz@openwrt.org>
++ */
++
++#include <linux/if_ether.h>
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++#include <linux/netdevice.h>
++#include <linux/etherdevice.h>
++#include <linux/platform_device.h>
++
++#include <asm/io.h>
++#include <asm/types.h>
++#include <asm/setup.h>
++#include <asm/memory.h>
++#include <mach/hardware.h>
++#include <asm/mach-types.h>
++#include <asm/irq.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++/* gpio mask used by platform device */
++#define TW2662_GPIO_MASK        (1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) 
++
++static struct flash_platform_data tw2662_flash_data = {
++	.map_name	= "cfi_probe",
++	.width		= 2,
++};
++
++static struct resource tw2662_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++};
++
++static struct platform_device tw2662_flash = {
++	.name		= "IXP4XX-Flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data = &tw2662_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &tw2662_flash_resource,
++};
++
++static struct resource tw2662_gpio_resources[] = {
++        {
++                .name   = "gpio",
++                /* FIXME: gpio mask should be model specific */
++                .start  = TW2662_GPIO_MASK,
++                .end    = TW2662_GPIO_MASK,
++                .flags  = 0,
++        },
++};
++
++static struct platform_device tw2662_gpio = {
++	.name			= "GPIODEV",
++	.id			= -1,
++	.num_resources		= ARRAY_SIZE(tw2662_gpio_resources),
++	.resource		= tw2662_gpio_resources,
++};
++
++static struct resource tw2662_uart_resources[] = {
++	{
++		.start		= IXP4XX_UART1_BASE_PHYS,
++		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	},
++	{
++		.start		= IXP4XX_UART2_BASE_PHYS,
++		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
++		.flags		= IORESOURCE_MEM
++	}
++};
++
++static struct plat_serial8250_port tw2662_uart_data[] = {
++	{
++		.mapbase	= IXP4XX_UART1_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART1,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{
++		.mapbase	= IXP4XX_UART2_BASE_PHYS,
++		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++		.irq		= IRQ_IXP4XX_UART2,
++		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= IXP4XX_UART_XTAL,
++	},
++	{ },
++};
++
++static struct platform_device tw2662_uart = {
++	.name			= "serial8250",
++	.id			= PLAT8250_DEV_PLATFORM,
++	.dev.platform_data	= tw2662_uart_data,
++	.num_resources		= 2,
++	.resource		= tw2662_uart_resources
++};
++
++/* Built-in 10/100 Ethernet MAC interfaces */
++static struct eth_plat_info tw2662_plat_eth[] = {
++        {
++                .phy            = 3,
++                .rxq            = 3,
++                .txreadyq       = 20,
++        }, {
++                .phy            = 1,
++                .rxq            = 4,
++                .txreadyq       = 21,
++        }
++};
++
++static struct platform_device tw2662_eth[] = {
++	{
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEB,
++		.dev.platform_data	= tw2662_plat_eth,
++	}, {
++		.name			= "ixp4xx_eth",
++		.id			= IXP4XX_ETH_NPEC,
++		.dev.platform_data	= tw2662_plat_eth + 1,
++	}
++};
++
++
++static struct platform_device *tw2662_devices[] __initdata = {
++	&tw2662_flash,
++	&tw2662_uart,
++	&tw2662_gpio,
++	&tw2662_eth[0],
++	&tw2662_eth[1],
++};
++
++static char tw2662_mem_fixup[] __initdata = "mem=64M ";
++
++static void __init tw2662_fixup(struct machine_desc *desc,
++		struct tag *tags, char **cmdline, struct meminfo *mi)
++
++{
++	struct tag *t = tags;
++	char *p = *cmdline;
++
++	/* Find the end of the tags table, taking note of any cmdline tag. */
++	for (; t->hdr.size; t = tag_next(t)) {
++		if (t->hdr.tag == ATAG_CMDLINE) {
++			p = t->u.cmdline.cmdline;
++		}
++	}
++
++	/* Overwrite the end of the table with a new cmdline tag. */
++	t->hdr.tag = ATAG_CMDLINE;
++	t->hdr.size = (sizeof (struct tag_header) +
++		strlen(tw2662_mem_fixup) + strlen(p) + 1 + 4) >> 2;
++	strlcpy(t->u.cmdline.cmdline, tw2662_mem_fixup, COMMAND_LINE_SIZE);
++	strlcpy(t->u.cmdline.cmdline + strlen(tw2662_mem_fixup), p,
++		COMMAND_LINE_SIZE - strlen(tw2662_mem_fixup));
++
++	/* Terminate the table. */
++	t = tag_next(t);
++	t->hdr.tag = ATAG_NONE;
++	t->hdr.size = 0;
++}
++
++static void __init tw2662_init(void)
++{
++	ixp4xx_sys_init();
++
++	tw2662_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++	tw2662_flash_resource.end =
++		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
++
++	platform_add_devices(tw2662_devices, ARRAY_SIZE(tw2662_devices));
++
++	if (!(is_valid_ether_addr(tw2662_plat_eth[0].hwaddr)))
++		random_ether_addr(tw2662_plat_eth[0].hwaddr);
++	if (!(is_valid_ether_addr(tw2662_plat_eth[1].hwaddr))) {
++		memcpy(tw2662_plat_eth[1].hwaddr, tw2662_plat_eth[0].hwaddr, ETH_ALEN);
++		tw2662_plat_eth[1].hwaddr[5] = (tw2662_plat_eth[0].hwaddr[5] + 1);
++	}
++
++}
++
++#ifdef CONFIG_MACH_TW2662
++MACHINE_START(TW2662, "Titan Wireless TW-266-2")
++	/* Maintainer: Alexandros C. Couloumbis <alex@ozo.com> */
++	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
++	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++	.fixup		= tw2662_fixup,
++	.map_io		= ixp4xx_map_io,
++	.init_irq	= ixp4xx_init_irq,
++	.timer		= &ixp4xx_timer,
++	.boot_params	= 0x0100,
++	.init_machine	= tw2662_init,
++MACHINE_END
++#endif
diff --git a/target/linux/ixp4xx/patches-2.6.37/600-skb_avoid_dmabounce.patch b/target/linux/ixp4xx/patches-2.6.37/600-skb_avoid_dmabounce.patch
new file mode 100644
index 0000000..5b0e3fd
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/600-skb_avoid_dmabounce.patch
@@ -0,0 +1,13 @@
+--- a/net/core/skbuff.c
++++ b/net/core/skbuff.c
+@@ -183,6 +183,10 @@ struct sk_buff *__alloc_skb(unsigned int
+ 		goto out;
+ 	prefetchw(skb);
+ 
++#ifdef CONFIG_ARCH_IXP4XX 
++	gfp_mask |= GFP_DMA;
++#endif
++
+ 	size = SKB_DATA_ALIGN(size);
+ 	data = kmalloc_node_track_caller(size + sizeof(struct skb_shared_info),
+ 			gfp_mask, node);
diff --git a/target/linux/ixp4xx/patches-2.6.37/601_arm_2.6.37_update.patch b/target/linux/ixp4xx/patches-2.6.37/601_arm_2.6.37_update.patch
new file mode 100644
index 0000000..3d7f167
--- /dev/null
+++ b/target/linux/ixp4xx/patches-2.6.37/601_arm_2.6.37_update.patch
@@ -0,0 +1,135 @@
+--- a/arch/arm/mach-ixp4xx/ap1000-setup.c
++++ b/arch/arm/mach-ixp4xx/ap1000-setup.c
+@@ -167,8 +167,6 @@ static void __init ap1000_init(void)
+ #ifdef CONFIG_MACH_AP1000
+ MACHINE_START(AP1000, "Lanready AP-1000")
+ 	/* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.fixup		= ap1000_fixup,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+--- a/arch/arm/mach-ixp4xx/cambria-setup.c
++++ b/arch/arm/mach-ixp4xx/cambria-setup.c
+@@ -563,8 +563,6 @@ late_initcall(cambria_model_setup);
+ 
+ MACHINE_START(CAMBRIA, "Gateworks Cambria series")
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+--- a/arch/arm/mach-ixp4xx/compex-setup.c
++++ b/arch/arm/mach-ixp4xx/compex-setup.c
+@@ -126,8 +126,6 @@ static void __init compex_init(void)
+ 
+ MACHINE_START(COMPEX, "Compex WP18 / NP18A")
+ 	/* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+--- a/arch/arm/mach-ixp4xx/mi424wr-setup.c
++++ b/arch/arm/mach-ixp4xx/mi424wr-setup.c
+@@ -333,8 +333,6 @@ static void __init mi424wr_init(void)
+ 
+ MACHINE_START(MI424WR, "Actiontec MI424WR")
+ 	/* Maintainer: Jose Vasconcellos */
+-	.phys_io	= IXP4XX_UART2_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_UART2_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+--- /dev/null
++++ b/arch/arm/mach-ixp4xx/modules.builtin
+@@ -0,0 +1,2 @@
++kernel/arch/arm/mach-ixp4xx/ixp4xx_qmgr.ko
++kernel/arch/arm/mach-ixp4xx/ixp4xx_npe.ko
+--- a/arch/arm/mach-ixp4xx/pronghorn-setup.c
++++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
+@@ -224,8 +224,6 @@ static void __init pronghorn_init(void)
+ 
+ MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn")
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+@@ -235,8 +233,6 @@ MACHINE_END
+ 
+ MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+--- a/arch/arm/mach-ixp4xx/sidewinder-setup.c
++++ b/arch/arm/mach-ixp4xx/sidewinder-setup.c
+@@ -139,8 +139,6 @@ static void __init sidewinder_init(void)
+ 
+ MACHINE_START(SIDEWINDER, "ADI Engineering Sidewinder")
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+--- a/arch/arm/mach-ixp4xx/tw2662-setup.c
++++ b/arch/arm/mach-ixp4xx/tw2662-setup.c
+@@ -200,8 +200,6 @@ static void __init tw2662_init(void)
+ #ifdef CONFIG_MACH_TW2662
+ MACHINE_START(TW2662, "Titan Wireless TW-266-2")
+ 	/* Maintainer: Alexandros C. Couloumbis <alex@ozo.com> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.fixup		= tw2662_fixup,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+--- a/arch/arm/mach-ixp4xx/tw5334-setup.c
++++ b/arch/arm/mach-ixp4xx/tw5334-setup.c
+@@ -152,8 +152,6 @@ static void __init tw5334_init(void)
+ #ifdef CONFIG_MACH_TW5334
+ MACHINE_START(TW5334, "Titan Wireless TW-533-4")
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+--- a/arch/arm/mach-ixp4xx/usr8200-setup.c
++++ b/arch/arm/mach-ixp4xx/usr8200-setup.c
+@@ -202,8 +202,6 @@ static void __init usr8200_init(void)
+ 
+ MACHINE_START(USR8200, "USRobotics USR8200")
+ 	/* Maintainer: Peter Denison <openwrt@marshadder.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,
+--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
++++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
+@@ -161,8 +161,6 @@ static void __init wg302v1_init(void)
+ #ifdef CONFIG_MACH_WG302V1
+ MACHINE_START(WG302V1, "Netgear WG302 v1 / WAG302 v1")
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.fixup		= wg302v1_fixup,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+--- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
++++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+@@ -157,8 +157,6 @@ static void __init wrt300nv2_init(void)
+ #ifdef CONFIG_MACH_WRT300NV2
+ MACHINE_START(WRT300NV2, "Linksys WRT300N v2")
+ 	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+-	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+-	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ 	.map_io		= ixp4xx_map_io,
+ 	.init_irq	= ixp4xx_init_irq,
+ 	.timer		= &ixp4xx_timer,