kirkwood: add support for 4.3

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47386

8 files changed, 921 insertions, 0 deletions

diff --git a/target/linux/kirkwood/patches-4.3/110-ib62x0.patch b/target/linux/kirkwood/patches-4.3/110-ib62x0.patch
new file mode 100644
index 0000000..153c41b
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/110-ib62x0.patch
@@ -0,0 +1,20 @@
+--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
++++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
+@@ -117,13 +117,13 @@
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x600000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@700000 {
++	partition@200000 {
+ 		label = "root";
+-		reg = <0x0700000 0xf900000>;
++		reg = <0x200000 0xfe00000>;
+ 	};
+ 
+ };
diff --git a/target/linux/kirkwood/patches-4.3/120-iconnect.patch b/target/linux/kirkwood/patches-4.3/120-iconnect.patch
new file mode 100644
index 0000000..c95579d
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/120-iconnect.patch
@@ -0,0 +1,41 @@
+--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
++++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
+@@ -155,28 +155,23 @@
+ 	status = "okay";
+ 
+ 	partition@0 {
+-		label = "uboot";
+-		reg = <0x0000000 0xc0000>;
++		label = "u-boot";
++		reg = <0x0000000 0xe0000>;
+ 	};
+ 
+-	partition@a0000 {
+-		label = "env";
+-		reg = <0xa0000 0x20000>;
++	partition@e0000 {
++		label = "u-boot environment";
++		reg = <0xe0000 0x100000>;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "zImage";
+-		reg = <0x100000 0x300000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@540000 {
+-		label = "initrd";
+-		reg = <0x540000 0x300000>;
+-	};
+-
+-	partition@980000 {
+-		label = "boot";
+-		reg = <0x980000 0x1f400000>;
++	partition@200000 {
++		label = "root";
++		reg = <0x200000 0x1fe00000>;
+ 	};
+ };
+ 
diff --git a/target/linux/kirkwood/patches-4.3/130-dockstar.patch b/target/linux/kirkwood/patches-4.3/130-dockstar.patch
new file mode 100644
index 0000000..b1ad669
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/130-dockstar.patch
@@ -0,0 +1,32 @@
+--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
++++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
+@@ -77,18 +77,22 @@
+ 
+ 	partition@0 {
+ 		label = "u-boot";
+-		reg = <0x0000000 0x100000>;
+-		read-only;
++		reg = <0x0000000 0xe0000>;
++	};
++
++	partition@e0000 {
++		label = "u-boot environment";
++		reg = <0xe0000 0x100000>;
+ 	};
+ 
+ 	partition@100000 {
+-		label = "uImage";
+-		reg = <0x0100000 0x400000>;
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
+ 	};
+ 
+-	partition@500000 {
+-		label = "data";
+-		reg = <0x0500000 0xfb00000>;
++	partition@200000 {
++		label = "root";
++		reg = <0x200000 0xfe00000>;
+ 	};
+ };
+ 
diff --git a/target/linux/kirkwood/patches-4.3/140-ea4500.patch b/target/linux/kirkwood/patches-4.3/140-ea4500.patch
new file mode 100644
index 0000000..4409394
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/140-ea4500.patch
@@ -0,0 +1,180 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -168,6 +168,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ 	kirkwood-ds411.dtb \
+ 	kirkwood-ds411j.dtb \
+ 	kirkwood-ds411slim.dtb \
++	kirkwood-ea4500.dtb \
+ 	kirkwood-goflexnet.dtb \
+ 	kirkwood-guruplug-server-plus.dtb \
+ 	kirkwood-ib62x0.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-ea4500.dts
+@@ -0,0 +1,167 @@
++/*
++ * kirkwood-ea4500.dts - Device Tree file for Linksys EA4500
++ *
++ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
++ * (c) 2013 Deutsche Telekom Innovation Laboratories
++ * (c) 2014 Luka Perkov <luka@openwrt.org>
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2.  This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6282.dtsi"
++
++/ {
++	model = "Linksys EA4500";
++	compatible = "linksys,ea4500", "marvell,kirkwood-88f6282", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x8000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8 earlyprintk";
++	};
++
++	mbus {
++		pcie-controller {
++			status = "okay";
++
++			pcie@1,0 {
++				status = "okay";
++			};
++
++			pcie@2,0 {
++				status = "okay";
++			};
++		};
++	};
++
++	ocp@f1000000 {
++		pinctrl: pin-controller@10000 {
++			pmx_led_white_health: pmx-led-white-health {
++				marvell,pins = "mpp7";
++				marvell,function = "gpo";
++			};
++			pmx_led_white_pulse: pmx-led-white-pulse {
++				marvell,pins = "mpp14";
++				marvell,function = "gpio";
++			};
++			pmx_btn_wps: pmx-btn-wps {
++				marvell,pins = "mpp47";
++				marvell,function = "gpio";
++			};
++			pmx_btn_reset: pmx-btn-reset {
++				marvell,pins = "mpp48";
++				marvell,function = "gpio";
++			};
++		};
++
++		rtc@10300 {
++			status = "disabled";
++		};
++
++		serial@12000 {
++			status = "okay";
++		};
++
++	};
++
++	gpio_keys {
++		compatible = "gpio-keys";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
++		pinctrl-names = "default";
++
++		button@15 {
++			label = "WPS Button";
++			linux,code = <KEY_WPS_BUTTON>;
++			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
++		};
++
++		button@16 {
++			label = "Reset Button";
++			linux,code = <KEY_RESTART>;
++			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
++		};
++	};
++
++	gpio-leds {
++		compatible = "gpio-leds";
++		pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
++		pinctrl-names = "default";
++
++		white-health {
++			label = "ea4500:white:health";
++			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
++		};
++
++		white-pulse {
++			label = "ea4500:white:pulse";
++			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
++		};
++	};
++
++	mvsw61xx {
++		compatible = "marvell,88e6171";
++		status = "okay";
++		reg = <0x10>;
++
++		mii-bus = <&mdio>;
++		cpu-port-0 = <5>;
++		cpu-port-1 = <6>;
++		is-indirect;
++	};
++};
++
++&nand {
++	status = "okay";
++	pinctrl-0 = <&pmx_nand>;
++	pinctrl-names = "default";
++
++	partition@0 {
++		label = "u-boot";
++		reg = <0x0000000 0x80000>;
++	};
++
++	partition@80000 {
++		label = "u-boot environment";
++		reg = <0x80000 0x20000>;
++	};
++
++	partition@200000 {
++		label = "kernel";
++		reg = <0x200000 0x200000>;
++	};
++
++	partition@400000 {
++		label = "root";
++		reg = <0x400000 0x1c00000>;
++	};
++};
++
++&mdio {
++	status = "okay";
++};
++
++&eth0 {
++	status = "okay";
++	ethernet0-port@0 {
++		speed = <1000>;
++		duplex = <1>;
++	};
++};
++
++&eth1 {
++	status = "okay";
++	ethernet1-port@0 {
++		speed = <1000>;
++		duplex = <1>;
++	};
++};
diff --git a/target/linux/kirkwood/patches-4.3/150-ea3500.patch b/target/linux/kirkwood/patches-4.3/150-ea3500.patch
new file mode 100644
index 0000000..a2d71e3
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/150-ea3500.patch
@@ -0,0 +1,173 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -168,6 +168,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ 	kirkwood-ds411.dtb \
+ 	kirkwood-ds411j.dtb \
+ 	kirkwood-ds411slim.dtb \
++	kirkwood-ea3500.dtb \
+ 	kirkwood-ea4500.dtb \
+ 	kirkwood-goflexnet.dtb \
+ 	kirkwood-guruplug-server-plus.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-ea3500.dts
+@@ -0,0 +1,160 @@
++/*
++ * kirkwood-ea3500.dts - Device Tree file for Linksys EA3500
++ *
++ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
++ * (c) 2013 Deutsche Telekom Innovation Laboratories
++ * (c) 2014 Luka Perkov <luka@openwrt.org>
++ * (c) 2014 Dan Walters <dan@walters.io>
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2.  This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6282.dtsi"
++
++/ {
++	model = "Linksys EA3500";
++	compatible = "linksys,ea3500", "marvell,kirkwood-88f6282", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x4000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8 earlyprintk";
++	};
++
++	mbus {
++		pcie-controller {
++			status = "okay";
++
++			pcie@1,0 {
++				status = "okay";
++			};
++
++			pcie@2,0 {
++				status = "okay";
++			};
++		};
++	};
++
++	ocp@f1000000 {
++		pinctrl: pin-controller@10000 {
++			pmx_led_green_power: pmx-led-green-power {
++				marvell,pins = "mpp7";
++				marvell,function = "gpo";
++			};
++			pmx_btn_wps: pmx-btn-wps {
++				marvell,pins = "mpp47";
++				marvell,function = "gpio";
++			};
++			pmx_btn_reset: pmx-btn-reset {
++				marvell,pins = "mpp48";
++				marvell,function = "gpio";
++			};
++		};
++
++		rtc@10300 {
++			status = "disabled";
++		};
++
++		serial@12000 {
++			status = "okay";
++		};
++
++	};
++
++	gpio_keys {
++		compatible = "gpio-keys";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
++		pinctrl-names = "default";
++
++		button@15 {
++			label = "WPS Button";
++			linux,code = <KEY_WPS_BUTTON>;
++			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
++		};
++
++		button@16 {
++			label = "Reset Button";
++			linux,code = <KEY_RESTART>;
++			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
++		};
++	};
++
++	gpio-leds {
++		compatible = "gpio-leds";
++		pinctrl-0 = < &pmx_led_green_power >;
++		pinctrl-names = "default";
++
++		green-power {
++			label = "ea3500:green:power";
++			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
++		};
++	};
++
++	mvsw61xx {
++		compatible = "marvell,88e6171";
++		status = "okay";
++		reg = <0x10>;
++
++		mii-bus = <&mdio>;
++		cpu-port-0 = <5>;
++		cpu-port-1 = <6>;
++		is-indirect;
++	};
++};
++
++&nand {
++	status = "okay";
++	pinctrl-0 = <&pmx_nand>;
++	pinctrl-names = "default";
++
++	partition@0 {
++		label = "u-boot";
++		reg = <0x0000000 0x80000>;
++		read-only;
++	};
++
++	partition@80000 {
++		label = "u-boot environment";
++		reg = <0x80000 0x20000>;
++	};
++
++	partition@200000 {
++		label = "kernel";
++		reg = <0x200000 0x200000>;
++	};
++
++	partition@400000 {
++		label = "root";
++		reg = <0x400000 0x1200000>;
++	};
++};
++
++&mdio {
++	status = "okay";
++};
++
++&eth0 {
++	status = "okay";
++	ethernet0-port@0 {
++		speed = <1000>;
++		duplex = <1>;
++	};
++};
++
++&eth1 {
++	status = "okay";
++	ethernet1-port@0 {
++		speed = <1000>;
++		duplex = <1>;
++	};
++};
diff --git a/target/linux/kirkwood/patches-4.3/160-goflexhome.patch b/target/linux/kirkwood/patches-4.3/160-goflexhome.patch
new file mode 100644
index 0000000..cdecbd1
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/160-goflexhome.patch
@@ -0,0 +1,140 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -170,6 +170,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ 	kirkwood-ds411slim.dtb \
+ 	kirkwood-ea3500.dtb \
+ 	kirkwood-ea4500.dtb \
++	kirkwood-goflexhome.dtb \
+ 	kirkwood-goflexnet.dtb \
+ 	kirkwood-guruplug-server-plus.dtb \
+ 	kirkwood-ib62x0.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
+@@ -0,0 +1,127 @@
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++
++/ {
++	model = "Seagate GoFlex Home";
++	compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x8000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
++		stdout-path = &uart0;
++	};
++
++	ocp@f1000000 {
++		pinctrl: pin-controller@10000 {
++			pmx_usb_power_enable: pmx-usb-power-enable {
++				marvell,pins = "mpp29";
++				marvell,function = "gpio";
++			};
++			pmx_led_white: pmx-led-white {
++				marvell,pins = "mpp40";
++				marvell,function = "gpio";
++			};
++			pmx_led_green: pmx-led_green {
++				marvell,pins = "mpp46";
++				marvell,function = "gpio";
++			};
++			pmx_led_orange: pmx-led-orange {
++				marvell,pins = "mpp47";
++				marvell,function = "gpio";
++			};
++		};
++		serial@12000 {
++			status = "ok";
++		};
++
++		sata@80000 {
++			status = "okay";
++			nr-ports = <2>;
++		};
++
++	};
++	gpio-leds {
++		compatible = "gpio-leds";
++
++		health {
++			label = "status:green:health";
++			gpios = <&gpio1 14 1>;
++			linux,default-trigger = "default-on";
++		};
++		fault {
++			label = "status:orange:fault";
++			gpios = <&gpio1 15 1>;
++		};
++		misc {
++			label = "status:white:misc";
++			gpios = <&gpio1 8 1>;
++			linux,default-trigger = "ide-disk";
++		};
++	};
++	regulators {
++		compatible = "simple-bus";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		pinctrl-0 = <&pmx_usb_power_enable>;
++		pinctrl-names = "default";
++
++		usb_power: regulator@1 {
++			compatible = "regulator-fixed";
++			reg = <1>;
++			regulator-name = "USB Power";
++			regulator-min-microvolt = <5000000>;
++			regulator-max-microvolt = <5000000>;
++			enable-active-high;
++			regulator-always-on;
++			regulator-boot-on;
++			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++		};
++	};
++};
++
++&nand {
++	chip-delay = <40>;
++	status = "okay";
++
++	partition@0 {
++		label = "u-boot";
++		reg = <0x0000000 0x100000>;
++		read-only;
++	};
++
++	partition@100000 {
++		label = "uImage";
++		reg = <0x0100000 0x400000>;
++	};
++
++	partition@500000 {
++		label = "pogoplug";
++		reg = <0x0500000 0x2000000>;
++	};
++
++	partition@2500000 {
++		label = "root";
++		reg = <0x02500000 0xd800000>;
++	};
++};
++
++&mdio {
++	status = "okay";
++
++	ethphy0: ethernet-phy@0 {
++		reg = <0>;
++	};
++};
++
++&eth0 {
++	status = "okay";
++	ethernet0-port@0 {
++		phy-handle = <&ethphy0>;
++	};
++};
diff --git a/target/linux/kirkwood/patches-4.3/170-nsa310s.patch b/target/linux/kirkwood/patches-4.3/170-nsa310s.patch
new file mode 100644
index 0000000..c348f72
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/170-nsa310s.patch
@@ -0,0 +1,300 @@
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
+@@ -0,0 +1,287 @@
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++
++/ {
++	model = "ZyXEL NSA310S";
++	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x10000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8 earlyprintk";
++		stdout-path = &uart0;
++	};
++
++	mbus {
++		pcie-controller {
++			status = "okay";
++
++			pcie@1,0 {
++				status = "okay";
++			};
++		};
++	};
++
++	ocp@f1000000 {
++		pinctrl: pin-controller@10000 {
++			pinctrl-names = "default";
++
++			pmx_sata0: pmx-sata0 {
++				marvell,pins;
++				marvell,function = "sata0";
++			};
++			pmx_sata1: pmx-sata1 {
++				marvell,pins;
++				marvell,function = "sata1";
++			};
++			pmx_usb_power: pmx-usb-power {
++				marvell,pins = "mpp21";
++				marvell,function = "gpio";
++			};
++			pmx_pwr_off: pmx-pwr-off {
++				marvell,pins = "mpp27";
++				marvell,function = "gpio";
++			};
++			pmx_btn_reset: pmx-btn-reset {
++				marvell,pins = "mpp24";
++				marvell,function = "gpio";
++			};
++			pmx_btn_copy: pmx-btn-copy {
++				marvell,pins = "mpp25";
++				marvell,function = "gpio";
++			};
++			pmx_btn_power: pmx-btn-power {
++				marvell,pins = "mpp26";
++				marvell,function = "gpio";
++			};
++			pmx_led_hdd2_green: pmx-led-hdd2-green {
++				marvell,pins = "mpp34";
++				marvell,function = "gpio";
++			};
++			pmx_led_hdd2_red: pmx-led-hdd2-red {
++				marvell,pins = "mpp12";
++				marvell,function = "gpio";
++			};
++			pmx_led_usb_green: pmx-led-usb-green {
++				marvell,pins = "mpp15";
++				marvell,function = "gpio";
++			};
++			pmx_led_copy_green: pmx-led-copy-green {
++				marvell,pins = "mpp22";
++				marvell,function = "gpio";
++			};
++			pmx_led_copy_red: pmx-led-copy-red {
++				marvell,pins = "mpp23";
++				marvell,function = "gpio";
++			};
++			pmx_led_sys_green: pmx-led-sys-green {
++				marvell,pins = "mpp28";
++				marvell,function = "gpio";
++			};
++			pmx_led_sys_orange: pmx-led-sys-orange {
++				marvell,pins = "mpp29";
++				marvell,function = "gpio";
++			};
++			pmx_led_hdd1_green: pmx-led-hdd1-green {
++				marvell,pins = "mpp16";
++				marvell,function = "gpio";
++			};
++			pmx_led_hdd1_red: pmx-led-hdd1-red {
++				marvell,pins = "mpp13";
++				marvell,function = "gpio";
++			};
++			pmx_pwr_sata1: pmx-pwr-sata1 {
++				marvell,pins = "mpp33";
++				marvell,function = "gpio";
++			};
++		};
++
++		serial@12000 {
++			status = "okay";
++		};
++
++		sata@80000 {
++			status = "okay";
++			nr-ports = <2>;
++		};
++
++		rtc@10300 {
++			status = "disabled";
++		};
++
++		i2c@11000 {
++			status = "okay";
++			ht1382: rtc@68 {
++				compatible = "htk,ht1382";
++				reg = <0x68>;
++			};
++		};
++	};
++
++	regulators {
++		compatible = "simple-bus";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		pinctrl-names = "default";
++		pinctrl-0 = <&pmx_usb_power &pmx_pwr_sata1>;
++
++		usb0_power: regulator@1 {
++			compatible = "regulator-fixed";
++			reg = <1>;
++			regulator-name = "USB Power";
++			regulator-min-microvolt = <5000000>;
++			regulator-max-microvolt = <5000000>;
++			regulator-always-on;
++			regulator-boot-on;
++			enable-active-high;
++			gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
++		};
++
++		sata1_power: regulator@2 {
++			compatible = "regulator-fixed";
++			reg = <2>;
++			regulator-name = "SATA1 Power";
++			regulator-min-microvolt = <5000000>;
++			regulator-max-microvolt = <5000000>;
++			regulator-always-on;
++			regulator-boot-on;
++			enable-active-high;
++			gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
++		};
++	};
++
++
++	gpio_keys {
++		compatible = "gpio-keys";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>;
++		pinctrl-names = "default";
++
++		button@1 {
++			label = "Power Button";
++			linux,code = <KEY_POWER>;
++			gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
++		};
++		button@2 {
++			label = "Copy Button";
++			linux,code = <KEY_COPY>;
++			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
++		};
++		button@3 {
++			label = "Reset Button";
++			linux,code = <KEY_RESTART>;
++			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
++		};
++	};
++
++	gpio-leds {
++		compatible = "gpio-leds";
++		pinctrl-0 = <&pmx_led_hdd2_green &pmx_led_hdd2_red
++				&pmx_led_usb_green
++				&pmx_led_sys_green &pmx_led_sys_orange
++				&pmx_led_copy_green &pmx_led_copy_red
++				&pmx_led_hdd1_green &pmx_led_hdd1_red>;
++		pinctrl-names = "default";
++
++		green-sys {
++			label = "nsa310s:green:sys";
++			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "timer";
++		};
++		orange-sys {
++			label = "nsa310s:orange:sys";
++			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++		};
++		green-hdd1 {
++			label = "nsa310s:green:hdd1";
++			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
++		};
++		red-hdd1 {
++			label = "nsa310s:red:hdd1";
++			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
++		};
++		green-hdd2 {
++			label = "nsa310s:green:hdd2";
++			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
++		};
++		red-hdd2 {
++			label = "nsa310s:red:hdd2";
++			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
++		};
++		green-usb {
++			label = "nsa310s:green:usb";
++			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++		};
++		green-copy {
++			label = "nsa310s:green:copy";
++			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ide-disk";
++		};
++		red-copy {
++			label = "nsa310s:red:copy";
++			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
++		};
++	};
++
++	gpio_poweroff {
++		compatible = "gpio-poweroff";
++		pinctrl-0 = <&pmx_pwr_off>;
++		pinctrl-names = "default";
++		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
++	};
++};
++
++&nand {
++	status = "okay";
++	chip-delay = <35>;
++
++	partition@0 {
++		label = "u-boot";
++		reg = <0x0000000 0xe0000>;
++	};
++
++	partition@e0000 {
++		label = "u-boot environment";
++		reg = <0xe0000 0x100000>;
++	};
++
++	partition@100000 {
++		label = "second stage u-boot";
++		reg = <0x100000 0x200000>;
++	};
++
++	partition@200000 {
++		label = "root";
++		reg = <0x200000 0xfe00000>;
++	};
++};
++
++&mdio {
++	status = "okay";
++	ethphy0: ethernet-phy@1 {
++		compatible = "marvell,88e1318s";
++		reg = <1>;
++		marvell,reg-init = <0x1 0x16 0x0 0x3>,
++							<0x1 0x10 0x0 0x1017>,
++							<0x1 0x11 0x0 0x4408>,
++							<0x1 0x16 0x0 0x0>,
++							<0x1 0x4 0x0 0x1e1>,
++							<0x1 0x9 0x0 0x300>,
++							<0x1 0x10 0x0 0x3860>,
++							<0x1 0x0 0x0 0x9140>;
++	};
++};
++
++&eth0 {
++	status = "okay";
++
++	ethernet0-port@0 {
++		phy-handle = <&ethphy0>;
++	};
++};
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -196,6 +196,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ 	kirkwood-ns2mini.dtb \
+ 	kirkwood-nsa310.dtb \
+ 	kirkwood-nsa310a.dtb \
++	kirkwood-nsa310s.dtb \
+ 	kirkwood-openblocks_a6.dtb \
+ 	kirkwood-openblocks_a7.dtb \
+ 	kirkwood-openrd-base.dtb \
diff --git a/target/linux/kirkwood/patches-4.3/200-disable-tso.patch b/target/linux/kirkwood/patches-4.3/200-disable-tso.patch
new file mode 100644
index 0000000..c421c18
--- /dev/null
+++ b/target/linux/kirkwood/patches-4.3/200-disable-tso.patch
@@ -0,0 +1,35 @@
+From: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
+Subject: [PATCH] net: mv643xx_eth: Make TSO disabled by default
+
+Data corruption has been observed to be produced by TSO. For instance,
+accessing files on a NFS-server with TSO enabled results in different data
+transferred each time.
+
+This has been observed only on Kirkwood platforms, i.e. with the mv643xx_eth
+driver. Same tests on platforms using the mvneta ethernet driver have
+passed without errors.
+
+Make TSO disabled by default for now, until we can found a proper fix
+for the regression.
+
+Fixes: 3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO')
+Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
+Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
+Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
+---
+--- a/drivers/net/ethernet/marvell/mv643xx_eth.c
++++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
+@@ -3178,11 +3178,11 @@ static int mv643xx_eth_probe(struct plat
+ 	dev->watchdog_timeo = 2 * HZ;
+ 	dev->base_addr = 0;
+ 
+-	dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO;
++	dev->features = NETIF_F_SG | NETIF_F_IP_CSUM;
+ 	dev->vlan_features = dev->features;
+ 
+ 	dev->features |= NETIF_F_RXCSUM;
+-	dev->hw_features = dev->features;
++	dev->hw_features = dev->features | NETIF_F_TSO;
+ 
+ 	dev->priv_flags |= IFF_UNICAST_FLT;
+ 	dev->gso_max_segs = MV643XX_MAX_TSO_SEGS;