lantiq: add support for indicating the boot state using three leds

The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to
indicate the current boot state. This patch adds support for such cases.

The existing led sequences should be the same as before.

Boards which are using a led different from power (like TDW89x0) are
changed to switch of the led after boot

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48041

2 files changed, 16 insertions, 54 deletions

diff --git a/target/linux/lantiq/base-files/etc/board.d/01_leds b/target/linux/lantiq/base-files/etc/board.d/01_leds
index a95c72c..ac9e14e 100755
--- a/target/linux/lantiq/base-files/etc/board.d/01_leds
+++ b/target/linux/lantiq/base-files/etc/board.d/01_leds
@@ -27,39 +27,21 @@ board_config_update
 board=$(lantiq_board_name)
 
 case "$board" in
-BTHOMEHUBV2B)
-	ucidef_set_led_default "power" "power" "soc:blue:power" "1"
-	;;
-BTHOMEHUBV3A)
-	ucidef_set_led_default "power" "power" "soc:blue:power" "1"
-	;;
 BTHOMEHUBV5A)
-	ucidef_set_led_default "power" "power" "soc:blue:power" "1"
 	ucidef_set_led_default "dimmed" "dimmed" "dimmed" "0"
 	;;
 VGV7510KW22)
-	ucidef_set_led_default "power" "power" "power" "1"
-	ucidef_set_led_default "power2" "power2" "power2" "0"
 	ucidef_set_led_wlan "wifi" "wifi" "wifi" "phy0radio"
 	;;
 VGV7519)
-	ucidef_set_led_default "power" "power" "power" "0"
-	ucidef_set_led_default "power2" "power2" "power2" "1"
 	ucidef_set_led_wlan "wifi" "wifi" "wireless_yellow" "phy0radio"
 	;;
 P2812HNUF*)
-	ucidef_set_led_default "power" "power" "power" "0"
-	ucidef_set_led_default "power2" "power2" "power2" "1"
 	ucidef_set_led_wlan "wifi" "wifi" "wireless_green" "phy0radio"
 	;;
 ARV7519RW22)
-	ucidef_set_led_default "power" "power" "power" "1"
 	ucidef_set_led_netdev "lan" "lan" "lan" "eth0.1"
 	;;
-ARV8539PW22)
-        ucidef_set_led_default "power" "power" "soc:green:power" "1"
-        ucidef_set_led_default "power2" "power2" "soc:red:power" "0"
-        ;;
 *)
 	;;
 esac
diff --git a/target/linux/lantiq/base-files/etc/diag.sh b/target/linux/lantiq/base-files/etc/diag.sh
index 0e65e61..8356bcd 100644
--- a/target/linux/lantiq/base-files/etc/diag.sh
+++ b/target/linux/lantiq/base-files/etc/diag.sh
@@ -1,54 +1,34 @@
 #!/bin/sh
-# Copyright (C) 2012-2013 OpenWrt.org
+# Copyright (C) 2010-2015 OpenWrt.org
 
 . /lib/functions/leds.sh
 . /lib/functions/lantiq.sh
 
-power="$(lantiq_get_dt_led_chosen power)"
-power1="$(lantiq_get_dt_led_chosen power1)"
-power2="$(lantiq_get_dt_led_chosen power2)"
-
-status_led="$power"
+boot="$(lantiq_get_dt_led_chosen boot)"
+failsafe="$(lantiq_get_dt_led_chosen failsafe)"
+running="$(lantiq_get_dt_led_chosen running)"
 
 set_state() {
+    status_led="$boot"
+
 	case "$1" in
 	preinit)
-		if [ -n "$power2" ]; then
-			status_led_on
-			status_led="$power2"
-			status_led_blink_preinit
-			status_led="$power"
-		else
-			status_led_blink_preinit
-		fi
+		status_led_blink_preinit
 		;;
 	failsafe)
-		if [ -n "$power2" ]; then
-			led_off "$power2"
-			status_led_blink_failsafe
-		elif [ -n "$power1" ]; then
-			status_led_off
-			status_led="$power1"
-			status_led_blink_failsafe
-			status_led="$power"
-		else
-			status_led_blink_failsafe
-		fi
+		status_led_off
+		status_led="$failsafe"
+		status_led_blink_failsafe
 		;;
 	preinit_regular)
-		if [ -n "$power2" ]; then
-			status_led_on
-			status_led="$power2"
-			status_led_blink_preinit_regular
-			status_led="$power"
-		else
-			status_led_blink_preinit_regular
-		fi
+		status_led_blink_preinit_regular
 		;;
 	done)
-		status_led_on
-		led_off "$power1"
-		led_off "$power2"
+		status_led_off
+		[ -n "$running" ] & {
+			status_led="$running"
+			status_led_on
+		}
 		;;
 	esac
 }