lntiq: add support for Astoria ARV7519RW.

These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.

Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>

SVN-Revision: 40329

6 files changed, 319 insertions, 0 deletions

diff --git a/target/linux/lantiq/base-files/etc/uci-defaults/02_network b/target/linux/lantiq/base-files/etc/uci-defaults/02_network
index ad12384..5768336 100644
--- a/target/linux/lantiq/base-files/etc/uci-defaults/02_network
+++ b/target/linux/lantiq/base-files/etc/uci-defaults/02_network
@@ -130,6 +130,11 @@ TDW8970)
 	lan_mac=$(mtd_get_mac_binary boardconfig 61696)
 	wan_mac=$(macaddr_add "$lan_mac" 1)
 	;;
+
+ARV7519*)
+	lan_mac=$(mtd_get_mac_binary boardconfig 22)
+	wan_mac=$(macaddr_add "$lan_mac" 1)
+	;;
 esac
 
 [ -z "$(ls /lib/modules/`uname -r`/ltq_atm*)" ] || set_atm_wan "$vpi" "$vci" "$encaps" "$payload"
diff --git a/target/linux/lantiq/dts/ARV7519RW.dtsi b/target/linux/lantiq/dts/ARV7519RW.dtsi
new file mode 100644
index 0000000..7790470
--- /dev/null
+++ b/target/linux/lantiq/dts/ARV7519RW.dtsi
@@ -0,0 +1,186 @@
+/include/ "vr9.dtsi"
+
+/ {
+
+	model = "ARV7519 - Astoria Networks ARV7519RW22-A-LT";
+	
+	chosen {
+		bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+	};
+	
+	memory@0 {
+		reg = <0x0 0x8000000>;
+	};
+	
+	fpi@10000000 {
+		
+		gpio: pinmux@E100B10 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+			
+			state_default: pinmux {
+				mdio {
+					lantiq,groups = "mdio";
+					lantiq,function = "mdio";
+				};
+				gphy-leds {
+					lantiq,groups = "gphy0 led1", "gphy1 led1";
+					lantiq,function = "gphy";
+					lantiq,pull = <2>;
+					lantiq,open-drain = <0>;
+					lantiq,output = <1>;
+				};
+				phy-rst {
+					lantiq,pins = "io42";
+					lantiq,pull = <0>;
+					lantiq,open-drain = <0>;
+					lantiq,output = <1>;
+				};
+				pcie-rst {
+					lantiq,pins = "io21";
+					lantiq,pull = <0>;
+					lantiq,output = <1>;
+				};
+			};
+		};
+
+		eth@E108000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "lantiq,xrx200-net";
+			reg = <	0xE108000 0x3000 /* switch */
+				0xE10B100 0x70 /* mdio */
+				0xE10B1D8 0x30 /* mii */
+				0xE10B308 0x30 /* pmac */
+			>;
+			interrupt-parent = <&icu0>;
+			interrupts = <73 72>;
+
+			lan: interface@0 {
+				compatible = "lantiq,xrx200-pdi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				mac-address = [ 00 11 22 33 44 55 ];
+
+				ethernet@2 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <2>;
+					phy-mode = "gmii";
+					phy-handle = <&phy11>;
+				};
+				ethernet@3 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <4>;
+					phy-mode = "gmii";
+					phy-handle = <&phy13>;
+				};
+			};
+			
+			wan: interface@1 {
+				compatible = "lantiq,xrx200-pdi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+				mac-address = [ 00 11 22 33 44 56 ];
+				lantiq,wan;
+				ethernet@4 {
+					compatible = "lantiq,xrx200-pdi-port";
+					reg = <0>;
+					phy-mode = "rgmii";
+					phy-handle = <&phy0>;
+				};
+			};
+
+			mdio@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "lantiq,xrx200-mdio";
+				phy0: ethernet-phy@0 {
+					reg = <0x0>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+				};
+				phy11: ethernet-phy@11 {
+					reg = <0x11>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+				};
+				phy13: ethernet-phy@13 {
+					reg = <0x13>;
+					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ifxhcd@E101000 {
+			status = "okay";
+			gpios = <&gpio 32 0>;
+			lantiq,portmask = <0x3>;
+		};
+	
+		pcie@d900000 {
+			status = "disabled";
+			compatible = "lantiq,pcie-xway";
+		};
+
+		pci@E105400 {
+			status = "disabled";
+			compatible = "lantiq,pci-xway";
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <100>;
+		reset {
+			label = "reset";
+			gpios = <&gpio 22 1>;
+			linux,code = <0x198>;
+		};
+
+		rfkill {
+			label = "rfkill";
+			gpios = <&gpio 45 1>;
+			linux,code = <0xf7>;
+		};
+		wps {
+			gpios = <&gpio 20 1>;
+			linux,code = <0x211>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		lan{						/* green */
+			label = "lan";
+			gpios = <&gpio 02 1>;
+		};
+		voice {						/* green */
+			label = "voice";
+			gpios = <&gpio 29 1>;
+		};
+		message1 {					/* red */
+			label = "message1";
+			gpios = <&gpio 10 1>;
+		};
+		message2 {					/* green */
+			label = "message2";
+			gpios = <&gpio 19 1>;
+		};
+		message3 {					/* orange */
+			label = "message3";
+			gpios = <&gpio 28 1>;
+		};		
+		alarm {						/* blue */
+			label = "alarm";
+			gpios = <&gpio 15 1>;
+		};
+		power {						/* red */
+			label = "power";
+			gpios = <&gpio 14 1>;
+			default-state = "on";
+		};
+	};
+};
diff --git a/target/linux/lantiq/dts/ARV7519RWV11.dts b/target/linux/lantiq/dts/ARV7519RWV11.dts
new file mode 100644
index 0000000..c77ffb4
--- /dev/null
+++ b/target/linux/lantiq/dts/ARV7519RWV11.dts
@@ -0,0 +1,50 @@
+/dts-v1/;
+
+
+/include/ "ARV7519RW.dtsi"
+
+/ {
+	fpi@10000000 {
+		localbus@0 {
+			nor-boot@0 {
+				compatible = "lantiq,nor";
+				bank-width = <2>;
+				reg = <0 0x0 0x2000000>, <1 0x2000000 0x2000000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "uboot";
+					reg = <0x000000000000 0x00060000>;
+					read-only;
+				};
+
+				partition@60000 {
+					label = "uboot_cfg";
+					reg = <0x000000060000 0x00020000>;
+					read-only;
+				};
+				
+				partition@80000 {
+					label = "firmware";
+					reg = <0x000000080000 0x01f00000>;
+				};
+				
+				partition@1f80000 {
+					label = "boardconfig";
+					reg = <0x000001f80000 0x00080000>;
+					read-only;
+
+				};	
+							
+
+				
+			};
+		};
+	};
+	gphy-xrx200 {
+		compatible = "lantiq,phy-xrx200";
+		firmware = "lantiq/vr9_phy11g_a1x.bin";  /*VR9 1.1*/
+		phys = [ 00 01 ];
+	};
+};
diff --git a/target/linux/lantiq/dts/ARV7519RWV12.dts b/target/linux/lantiq/dts/ARV7519RWV12.dts
new file mode 100644
index 0000000..6f1bf51
--- /dev/null
+++ b/target/linux/lantiq/dts/ARV7519RWV12.dts
@@ -0,0 +1,50 @@
+/dts-v1/;
+
+
+/include/ "ARV7519RW.dtsi"
+
+/ {
+	fpi@10000000 {
+		localbus@0 {
+			nor-boot@0 {
+				compatible = "lantiq,nor";
+				bank-width = <2>;
+				reg = <0 0x0 0x2000000>, <1 0x2000000 0x2000000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "uboot";
+					reg = <0x000000000000 0x00060000>;
+					read-only;
+				};
+
+				partition@60000 {
+					label = "uboot_cfg";
+					reg = <0x000000060000 0x00020000>;
+					read-only;
+				};
+				
+				partition@80000 {
+					label = "firmware";
+					reg = <0x000000080000 0x01f00000>;
+				};
+				
+				partition@1f80000 {
+					label = "boardconfig";
+					reg = <0x000001f80000 0x00080000>;
+					read-only;
+
+				};		
+							
+
+				
+			};
+		};
+	};
+	gphy-xrx200 {
+		compatible = "lantiq,phy-xrx200";
+		firmware = "lantiq/vr9_phy11g_a2x.bin";  /*VR9 1.2*/
+		phys = [ 00 01 ];
+	};
+};
diff --git a/target/linux/lantiq/image/Makefile b/target/linux/lantiq/image/Makefile
index cd36d12..28cb96c 100644
--- a/target/linux/lantiq/image/Makefile
+++ b/target/linux/lantiq/image/Makefile
@@ -307,6 +307,12 @@ Image/Build/Profile/H201L=$(call Image/Build/$(1),$(1),H201L)
 Image/BuildKernel/Profile/P2601HNFX=$(call Image/BuildKernel/Template,P2601HNFX)
 Image/Build/Profile/P2601HNFX=$(call Image/Build/$(1),$(1),P2601HNFX)
 
+Image/BuildKernel/Profile/ARV7519RWV11=$(call Image/BuildKernel/Template,ARV7519RWV11,$(1))
+Image/Build/Profile/ARV7519RWV11=$(call Image/Build/$(1), $(1),ARV7519RWV11)
+
+Image/BuildKernel/Profile/ARV7519RWV12=$(call Image/BuildKernel/Template,ARV7519RWV12,$(1))
+Image/Build/Profile/ARV7519RWV12=$(call Image/Build/$(1), $(1),ARV7519RWV12)
+
 endif
 
 
diff --git a/target/linux/lantiq/xrx200/profiles/arv.mk b/target/linux/lantiq/xrx200/profiles/arv.mk
index 3172971..ce6f761 100644
--- a/target/linux/lantiq/xrx200/profiles/arv.mk
+++ b/target/linux/lantiq/xrx200/profiles/arv.mk
@@ -27,3 +27,25 @@ define Profile/VGV7519BRN
 endef
 
 $(eval $(call Profile,VGV7519BRN))
+
+define Profile/ARV7519RWV11
+  NAME:=Livebox Astoria V1
+  PACKAGES:=kmod-ath9k wpad-mini \
+	kmod-ltq-deu-vr9 kmod-ltq-hcd-vr9 \
+	kmod-ltq-vdsl-vr9-mei kmod-ltq-vdsl-vr9 \
+	kmod-ltq-atm-vr9 ltq-vdsl-vr9-fw-installer \
+	ltq-vdsl-app ppp-mod-pppoa
+endef
+
+$(eval $(call Profile,ARV7519RWV11))
+
+define Profile/ARV7519RWV12
+  NAME:=Livebox Astoria V2
+  PACKAGES:=kmod-ath9k wpad-mini \
+	kmod-ltq-deu-vr9 kmod-ltq-hcd-vr9 \
+	kmod-ltq-vdsl-vr9-mei kmod-ltq-vdsl-vr9 \
+	kmod-ltq-atm-vr9 ltq-vdsl-vr9-fw-installer \
+	ltq-vdsl-app ppp-mod-pppoa
+endef
+
+$(eval $(call Profile,ARV7519RWV12))