add preliminary Marvell Orion support

SVN-Revision: 11352

19 files changed, 3991 insertions, 0 deletions

diff --git a/target/linux/orion/patches/001-latencytop_support.patch b/target/linux/orion/patches/001-latencytop_support.patch
new file mode 100644
index 0000000..a1fbc17
--- /dev/null
+++ b/target/linux/orion/patches/001-latencytop_support.patch
@@ -0,0 +1,82 @@
+From: Nicolas Pitre <nico@cam.org>
+
+Signed-off-by: Nicolas Pitre <nico@marvell.com>
+Tested-by: Lennert Buytenhek <buytenh@marvell.com>
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/Kconfig             |    4 ++++
+ arch/arm/kernel/stacktrace.c |   26 ++++++++++++++++++++++----
+ 2 files changed, 26 insertions(+), 4 deletions(-)
+
+--- a/arch/arm/Kconfig
++++ b/arch/arm/Kconfig
+@@ -84,6 +84,10 @@
+ 	bool
+ 	default y
+ 
++config HAVE_LATENCYTOP_SUPPORT
++	bool
++	default y
++
+ config LOCKDEP_SUPPORT
+ 	bool
+ 	default y
+--- a/arch/arm/kernel/stacktrace.c
++++ b/arch/arm/kernel/stacktrace.c
+@@ -36,6 +36,7 @@
+ #ifdef CONFIG_STACKTRACE
+ struct stack_trace_data {
+ 	struct stack_trace *trace;
++	unsigned int no_sched_functions;
+ 	unsigned int skip;
+ };
+ 
+@@ -43,27 +44,44 @@
+ {
+ 	struct stack_trace_data *data = d;
+ 	struct stack_trace *trace = data->trace;
++	unsigned long addr = frame->lr;
+ 
++	if (data->no_sched_functions && in_sched_functions(addr))
++		return 0;
+ 	if (data->skip) {
+ 		data->skip--;
+ 		return 0;
+ 	}
+ 
+-	trace->entries[trace->nr_entries++] = frame->lr;
++	trace->entries[trace->nr_entries++] = addr;
+ 
+ 	return trace->nr_entries >= trace->max_entries;
+ }
+ 
+-void save_stack_trace(struct stack_trace *trace)
++void save_stack_trace_tsk(struct task_struct *tsk, struct stack_trace *trace)
+ {
+ 	struct stack_trace_data data;
+ 	unsigned long fp, base;
+ 
+ 	data.trace = trace;
+ 	data.skip = trace->skip;
+-	base = (unsigned long)task_stack_page(current);
+-	asm("mov %0, fp" : "=r" (fp));
++	base = (unsigned long)task_stack_page(tsk);
++
++	if (tsk != current) {
++		data.no_sched_functions = 1;
++		fp = thread_saved_fp(tsk);
++	} else {
++		data.no_sched_functions = 0;
++		asm("mov %0, fp" : "=r" (fp));
++	}
+ 
+ 	walk_stackframe(fp, base, base + THREAD_SIZE, save_trace, &data);
++	if (trace->nr_entries < trace->max_entries)
++		trace->entries[trace->nr_entries++] = ULONG_MAX;
++}
++
++void save_stack_trace(struct stack_trace *trace)
++{
++	save_stack_trace_tsk(current, trace);
+ }
+ #endif
diff --git a/target/linux/orion/patches/002-feroceon__speed_up_flushing_of_the_entire_cache.patch b/target/linux/orion/patches/002-feroceon__speed_up_flushing_of_the_entire_cache.patch
new file mode 100644
index 0000000..c2efe5b
--- /dev/null
+++ b/target/linux/orion/patches/002-feroceon__speed_up_flushing_of_the_entire_cache.patch
@@ -0,0 +1,117 @@
+Flushing the L1 D cache with a test/clean/invalidate loop is very
+easy in software, but it is not the quickest way of doing it, as
+there is a lot of overhead involved in re-scanning the cache from
+the beginning every time we hit a dirty line.
+
+This patch makes proc-feroceon.S use "clean+invalidate by set/way"
+loops according to possible cache configuration of Feroceon CPUs
+(either direct-mapped or 4-way set associative).
+
+[nico: optimized the assembly a bit]
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+Signed-off-by: Nicolas Pitre <nico@marvell.com>
+---
+ arch/arm/mm/proc-feroceon.S |   53 ++++++++++++++++++++++++++++++++++---------
+ 1 files changed, 42 insertions(+), 11 deletions(-)
+
+--- a/arch/arm/mm/proc-feroceon.S
++++ b/arch/arm/mm/proc-feroceon.S
+@@ -44,11 +44,31 @@
+  */
+ #define CACHE_DLINESIZE	32
+ 
++	.bss
++	.align 3
++__cache_params_loc:
++	.space	8
++
+ 	.text
++__cache_params:
++	.word	__cache_params_loc
++
+ /*
+  * cpu_feroceon_proc_init()
+  */
+ ENTRY(cpu_feroceon_proc_init)
++	mrc	p15, 0, r0, c0, c0, 1		@ read cache type register
++	ldr	r1, __cache_params
++	mov	r2, #(16 << 5)
++	tst	r0, #(1 << 16)			@ get way
++	mov	r0, r0, lsr #18			@ get cache size order
++	movne	r3, #((4 - 1) << 30)		@ 4-way
++	and	r0, r0, #0xf
++	moveq	r3, #0				@ 1-way
++	mov	r2, r2, lsl r0			@ actual cache size
++	movne	r2, r2, lsr #2			@ turned into # of sets
++	sub	r2, r2, #(1 << 5)
++	stmia	r1, {r2, r3}
+ 	mov	pc, lr
+ 
+ /*
+@@ -117,11 +137,19 @@
+  */
+ ENTRY(feroceon_flush_kern_cache_all)
+ 	mov	r2, #VM_EXEC
+-	mov	ip, #0
++
+ __flush_whole_cache:
+-1:	mrc	p15, 0, r15, c7, c14, 3 	@ test,clean,invalidate
+-	bne	1b
++	ldr	r1, __cache_params
++	ldmia	r1, {r1, r3}
++1:	orr	ip, r1, r3
++2:	mcr	p15, 0, ip, c7, c14, 2		@ clean + invalidate D set/way
++	subs	ip, ip, #(1 << 30)		@ next way
++	bcs	2b
++	subs	r1, r1, #(1 << 5)		@ next set
++	bcs	1b
++
+ 	tst	r2, #VM_EXEC
++	mov	ip, #0
+ 	mcrne	p15, 0, ip, c7, c5, 0		@ invalidate I cache
+ 	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
+ 	mov	pc, lr
+@@ -138,7 +166,6 @@
+  */
+ 	.align	5
+ ENTRY(feroceon_flush_user_cache_range)
+-	mov	ip, #0
+ 	sub	r3, r1, r0			@ calculate total size
+ 	cmp	r3, #CACHE_DLIMIT
+ 	bgt	__flush_whole_cache
+@@ -152,6 +179,7 @@
+ 	cmp	r0, r1
+ 	blo	1b
+ 	tst	r2, #VM_EXEC
++	mov	ip, #0
+ 	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
+ 	mov	pc, lr
+ 
+@@ -306,16 +334,19 @@
+ 	.align	5
+ ENTRY(cpu_feroceon_switch_mm)
+ #ifdef CONFIG_MMU
+-	mov	ip, #0
+-@ && 'Clean & Invalidate whole DCache'
+-1:	mrc	p15, 0, r15, c7, c14, 3 	@ test,clean,invalidate
+-	bne	1b
+-	mcr	p15, 0, ip, c7, c5, 0		@ invalidate I cache
+-	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
++	mov	r2, lr				@ abuse r2 to preserve lr
++	bl	__flush_whole_cache
++	@ if r2 contains the VM_EXEC bit then the next 2 ops are done already
++	tst	r2, #VM_EXEC
++	mcreq	p15, 0, ip, c7, c5, 0		@ invalidate I cache
++	mcreq	p15, 0, ip, c7, c10, 4		@ drain WB
++
+ 	mcr	p15, 0, r0, c2, c0, 0		@ load page table pointer
+ 	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I & D TLBs
+-#endif
++	mov	pc, r2
++#else
+ 	mov	pc, lr
++#endif
+ 
+ /*
+  * cpu_feroceon_set_pte_ext(ptep, pte, ext)
diff --git a/target/linux/orion/patches/003-fix_various_whitespace_and_coding_style.patch b/target/linux/orion/patches/003-fix_various_whitespace_and_coding_style.patch
new file mode 100644
index 0000000..02126ca
--- /dev/null
+++ b/target/linux/orion/patches/003-fix_various_whitespace_and_coding_style.patch
@@ -0,0 +1,647 @@
+More cosmetic cleanup:
+- Replace 8-space indents by proper tab indents.
+- In structure initialisers, use a trailing comma for every member.
+- Collapse "},\n{" in structure initialiers to "}, {".
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/common.c            |   91 +++++++++++--------------
+ arch/arm/mach-orion5x/db88f5281-setup.c   |   13 ++--
+ arch/arm/mach-orion5x/dns323-setup.c      |   33 +++++----
+ arch/arm/mach-orion5x/kurobox_pro-setup.c |    8 +--
+ arch/arm/mach-orion5x/pci.c               |   14 ++--
+ arch/arm/mach-orion5x/rd88f5182-setup.c   |    3 +-
+ arch/arm/mach-orion5x/ts209-setup.c       |  103 +++++++++++++++--------------
+ arch/arm/mm/proc-feroceon.S               |    8 +-
+ 8 files changed, 132 insertions(+), 141 deletions(-)
+
+--- a/arch/arm/mach-orion5x/common.c
++++ b/arch/arm/mach-orion5x/common.c
+@@ -39,25 +39,22 @@
+ 		.virtual	= ORION5X_REGS_VIRT_BASE,
+ 		.pfn		= __phys_to_pfn(ORION5X_REGS_PHYS_BASE),
+ 		.length		= ORION5X_REGS_SIZE,
+-		.type		= MT_DEVICE
+-	},
+-	{
++		.type		= MT_DEVICE,
++	}, {
+ 		.virtual	= ORION5X_PCIE_IO_VIRT_BASE,
+ 		.pfn		= __phys_to_pfn(ORION5X_PCIE_IO_PHYS_BASE),
+ 		.length		= ORION5X_PCIE_IO_SIZE,
+-		.type		= MT_DEVICE
+-	},
+-	{
++		.type		= MT_DEVICE,
++	}, {
+ 		.virtual	= ORION5X_PCI_IO_VIRT_BASE,
+ 		.pfn		= __phys_to_pfn(ORION5X_PCI_IO_PHYS_BASE),
+ 		.length		= ORION5X_PCI_IO_SIZE,
+-		.type		= MT_DEVICE
+-	},
+-	{
++		.type		= MT_DEVICE,
++	}, {
+ 		.virtual	= ORION5X_PCIE_WA_VIRT_BASE,
+ 		.pfn		= __phys_to_pfn(ORION5X_PCIE_WA_PHYS_BASE),
+ 		.length		= ORION5X_PCIE_WA_SIZE,
+-		.type		= MT_DEVICE
++		.type		= MT_DEVICE,
+ 	},
+ };
+ 
+@@ -75,18 +72,15 @@
+ 		.start		= UART0_PHYS_BASE,
+ 		.end		= UART0_PHYS_BASE + 0xff,
+ 		.flags		= IORESOURCE_MEM,
+-	},
+-	{
++	}, {
+ 		.start		= IRQ_ORION5X_UART0,
+ 		.end		= IRQ_ORION5X_UART0,
+ 		.flags		= IORESOURCE_IRQ,
+-	},
+-	{
++	}, {
+ 		.start		= UART1_PHYS_BASE,
+ 		.end		= UART1_PHYS_BASE + 0xff,
+ 		.flags		= IORESOURCE_MEM,
+-	},
+-	{
++	}, {
+ 		.start		= IRQ_ORION5X_UART1,
+ 		.end		= IRQ_ORION5X_UART1,
+ 		.flags		= IORESOURCE_IRQ,
+@@ -102,8 +96,7 @@
+ 		.iotype		= UPIO_MEM,
+ 		.regshift	= 2,
+ 		.uartclk	= ORION5X_TCLK,
+-	},
+-	{
++	}, {
+ 		.mapbase	= UART1_PHYS_BASE,
+ 		.membase	= (char *)UART1_VIRT_BASE,
+ 		.irq		= IRQ_ORION5X_UART1,
+@@ -111,8 +104,8 @@
+ 		.iotype		= UPIO_MEM,
+ 		.regshift	= 2,
+ 		.uartclk	= ORION5X_TCLK,
++	}, {
+ 	},
+-	{ },
+ };
+ 
+ static struct platform_device orion5x_uart = {
+@@ -134,8 +127,7 @@
+ 		.start	= ORION5X_USB0_PHYS_BASE,
+ 		.end	= ORION5X_USB0_PHYS_BASE + SZ_4K - 1,
+ 		.flags	= IORESOURCE_MEM,
+-	},
+-	{
++	}, {
+ 		.start	= IRQ_ORION5X_USB0_CTRL,
+ 		.end	= IRQ_ORION5X_USB0_CTRL,
+ 		.flags	= IORESOURCE_IRQ,
+@@ -147,8 +139,7 @@
+ 		.start	= ORION5X_USB1_PHYS_BASE,
+ 		.end	= ORION5X_USB1_PHYS_BASE + SZ_4K - 1,
+ 		.flags	= IORESOURCE_MEM,
+-	},
+-	{
++	}, {
+ 		.start	= IRQ_ORION5X_USB1_CTRL,
+ 		.end	= IRQ_ORION5X_USB1_CTRL,
+ 		.flags	= IORESOURCE_IRQ,
+@@ -219,7 +210,7 @@
+ 		.start	= IRQ_ORION5X_ETH_SUM,
+ 		.end	= IRQ_ORION5X_ETH_SUM,
+ 		.flags	= IORESOURCE_IRQ,
+-	}
++	},
+ };
+ 
+ static struct platform_device orion5x_eth = {
+@@ -251,16 +242,15 @@
+ 
+ static struct resource orion5x_i2c_resources[] = {
+ 	{
+-		.name   = "i2c base",
+-		.start  = I2C_PHYS_BASE,
+-		.end    = I2C_PHYS_BASE + 0x20 -1,
+-		.flags  = IORESOURCE_MEM,
+-	},
+-	{
+-		.name   = "i2c irq",
+-		.start  = IRQ_ORION5X_I2C,
+-		.end    = IRQ_ORION5X_I2C,
+-		.flags  = IORESOURCE_IRQ,
++		.name	= "i2c base",
++		.start	= I2C_PHYS_BASE,
++		.end	= I2C_PHYS_BASE + 0x20 -1,
++		.flags	= IORESOURCE_MEM,
++	}, {
++		.name	= "i2c irq",
++		.start	= IRQ_ORION5X_I2C,
++		.end	= IRQ_ORION5X_I2C,
++		.flags	= IORESOURCE_IRQ,
+ 	},
+ };
+ 
+@@ -270,7 +260,7 @@
+ 	.num_resources	= ARRAY_SIZE(orion5x_i2c_resources),
+ 	.resource	= orion5x_i2c_resources,
+ 	.dev		= {
+-		.platform_data = &orion5x_i2c_pdata,
++		.platform_data	= &orion5x_i2c_pdata,
+ 	},
+ };
+ 
+@@ -278,28 +268,27 @@
+  * Sata port
+  ****************************************************************************/
+ static struct resource orion5x_sata_resources[] = {
+-        {
+-                .name   = "sata base",
+-                .start  = ORION5X_SATA_PHYS_BASE,
+-                .end    = ORION5X_SATA_PHYS_BASE + 0x5000 - 1,
+-                .flags  = IORESOURCE_MEM,
+-        },
+ 	{
+-                .name   = "sata irq",
+-                .start  = IRQ_ORION5X_SATA,
+-                .end    = IRQ_ORION5X_SATA,
+-                .flags  = IORESOURCE_IRQ,
+-        },
++		.name	= "sata base",
++		.start	= ORION5X_SATA_PHYS_BASE,
++		.end	= ORION5X_SATA_PHYS_BASE + 0x5000 - 1,
++		.flags	= IORESOURCE_MEM,
++	}, {
++		.name	= "sata irq",
++		.start	= IRQ_ORION5X_SATA,
++		.end	= IRQ_ORION5X_SATA,
++		.flags	= IORESOURCE_IRQ,
++	},
+ };
+ 
+ static struct platform_device orion5x_sata = {
+-	.name           = "sata_mv",
+-	.id             = 0,
++	.name		= "sata_mv",
++	.id		= 0,
+ 	.dev		= {
+ 		.coherent_dma_mask	= 0xffffffff,
+ 	},
+-	.num_resources  = ARRAY_SIZE(orion5x_sata_resources),
+-	.resource       = orion5x_sata_resources,
++	.num_resources	= ARRAY_SIZE(orion5x_sata_resources),
++	.resource	= orion5x_sata_resources,
+ };
+ 
+ void __init orion5x_sata_init(struct mv_sata_platform_data *sata_data)
+@@ -319,7 +308,7 @@
+ }
+ 
+ struct sys_timer orion5x_timer = {
+-        .init = orion5x_timer_init,
++	.init = orion5x_timer_init,
+ };
+ 
+ /*****************************************************************************
+--- a/arch/arm/mach-orion5x/db88f5281-setup.c
++++ b/arch/arm/mach-orion5x/db88f5281-setup.c
+@@ -86,7 +86,7 @@
+ 	.name		= "physmap-flash",
+ 	.id		= 0,
+ 	.dev		= {
+-		.platform_data = &db88f5281_boot_flash_data,
++		.platform_data	= &db88f5281_boot_flash_data,
+ 	},
+ 	.num_resources	= 1,
+ 	.resource	= &db88f5281_boot_flash_resource,
+@@ -110,7 +110,7 @@
+ 	.name		= "physmap-flash",
+ 	.id		= 1,
+ 	.dev		= {
+-		.platform_data = &db88f5281_nor_flash_data,
++		.platform_data	= &db88f5281_nor_flash_data,
+ 	},
+ 	.num_resources	= 1,
+ 	.resource	= &db88f5281_nor_flash_resource,
+@@ -125,18 +125,15 @@
+ 		.name = "kernel",
+ 		.offset = 0,
+ 		.size = SZ_2M,
+-	},
+-	{
++	}, {
+ 		.name = "root",
+ 		.offset = SZ_2M,
+ 		.size = (SZ_16M - SZ_2M),
+-	},
+-	{
++	}, {
+ 		.name = "user",
+ 		.offset = SZ_16M,
+ 		.size = SZ_8M,
+-	},
+-	{
++	}, {
+ 		.name = "recovery",
+ 		.offset = (SZ_16M + SZ_8M),
+ 		.size = SZ_8M,
+--- a/arch/arm/mach-orion5x/dns323-setup.c
++++ b/arch/arm/mach-orion5x/dns323-setup.c
+@@ -119,7 +119,7 @@
+ 		.name	= "u-boot",
+ 		.size	= 0x00030000,
+ 		.offset	= 0x007d0000,
+-	}
++	},
+ };
+ 
+ static struct physmap_flash_data dns323_nor_flash_data = {
+@@ -137,7 +137,9 @@
+ static struct platform_device dns323_nor_flash = {
+ 	.name		= "physmap-flash",
+ 	.id		= 0,
+-	.dev		= { .platform_data = &dns323_nor_flash_data, },
++	.dev		= {
++		.platform_data	= &dns323_nor_flash_data,
++	},
+ 	.resource	= &dns323_nor_flash_resource,
+ 	.num_resources	= 1,
+ };
+@@ -170,7 +172,9 @@
+ static struct platform_device dns323_gpio_leds = {
+ 	.name		= "leds-gpio",
+ 	.id		= -1,
+-	.dev		= { .platform_data = &dns323_led_data, },
++	.dev		= {
++		.platform_data	= &dns323_led_data,
++	},
+ };
+ 
+ /****************************************************************************
+@@ -183,25 +187,26 @@
+ 		.gpio		= DNS323_GPIO_KEY_RESET,
+ 		.desc		= "Reset Button",
+ 		.active_low	= 1,
+-	},
+-	{
++	}, {
+ 		.code		= KEY_POWER,
+ 		.gpio		= DNS323_GPIO_KEY_POWER,
+ 		.desc		= "Power Button",
+ 		.active_low	= 1,
+-	}
++	},
+ };
+ 
+ static struct gpio_keys_platform_data dns323_button_data = {
+ 	.buttons	= dns323_buttons,
+-	.nbuttons       = ARRAY_SIZE(dns323_buttons),
++	.nbuttons	= ARRAY_SIZE(dns323_buttons),
+ };
+ 
+ static struct platform_device dns323_button_device = {
+ 	.name		= "gpio-keys",
+ 	.id		= -1,
+ 	.num_resources	= 0,
+-	.dev		= { .platform_data  = &dns323_button_data, },
++	.dev		= {
++		.platform_data	= &dns323_button_data,
++	},
+ };
+ 
+ /****************************************************************************
+@@ -225,17 +230,15 @@
+ static struct i2c_board_info __initdata dns323_i2c_devices[] = {
+ 	{
+ 		I2C_BOARD_INFO("g760a", 0x3e),
+-	},
+ #if 0
+ 	/* this entry requires the new-style driver model lm75 driver,
+ 	 * for the meantime "insmod lm75.ko force_lm75=0,0x48" is needed */
+-	{
++	}, {
+ 		I2C_BOARD_INFO("g751", 0x48),
+-	},
+ #endif
+-	{
++	}, {
+ 		I2C_BOARD_INFO("m41t80", 0x68),
+-	}
++	},
+ };
+ 
+ /* DNS-323 specific power off method */
+@@ -292,8 +295,8 @@
+ 	orion5x_gpio_set_valid_pins(0x07f6);
+ 
+ 	/* register dns323 specific power-off method */
+-	if ((gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0)
+-	    || (gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0))
++	if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 ||
++	    gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0)
+ 		pr_err("DNS323: failed to setup power-off GPIO\n");
+ 
+ 	pm_power_off = dns323_power_off;
+--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
++++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
+@@ -53,13 +53,11 @@
+ 		.name	= "uImage",
+ 		.offset	= 0,
+ 		.size	= SZ_4M,
+-	},
+-	{
++	}, {
+ 		.name	= "rootfs",
+ 		.offset	= SZ_4M,
+ 		.size	= SZ_64M,
+-	},
+-	{
++	}, {
+ 		.name	= "extra",
+ 		.offset	= SZ_4M + SZ_64M,
+ 		.size	= SZ_256M - (SZ_4M + SZ_64M),
+@@ -175,7 +173,7 @@
+  * SATA
+  ****************************************************************************/
+ static struct mv_sata_platform_data kurobox_pro_sata_data = {
+-	.n_ports        = 2,
++	.n_ports	= 2,
+ };
+ 
+ /*****************************************************************************
+--- a/arch/arm/mach-orion5x/pci.c
++++ b/arch/arm/mach-orion5x/pci.c
+@@ -240,13 +240,13 @@
+  * PCI Address Decode Windows registers
+  */
+ #define PCI_BAR_SIZE_DDR_CS(n)	(((n) == 0) ? ORION5X_PCI_REG(0xc08) : \
+-				((n) == 1) ? ORION5X_PCI_REG(0xd08) :  \
+-				((n) == 2) ? ORION5X_PCI_REG(0xc0c) :  \
+-				((n) == 3) ? ORION5X_PCI_REG(0xd0c) : 0)
+-#define PCI_BAR_REMAP_DDR_CS(n)	(((n) ==0) ? ORION5X_PCI_REG(0xc48) :  \
+-				((n) == 1) ? ORION5X_PCI_REG(0xd48) :  \
+-				((n) == 2) ? ORION5X_PCI_REG(0xc4c) :  \
+-				((n) == 3) ? ORION5X_PCI_REG(0xd4c) : 0)
++				 ((n) == 1) ? ORION5X_PCI_REG(0xd08) : \
++				 ((n) == 2) ? ORION5X_PCI_REG(0xc0c) : \
++				 ((n) == 3) ? ORION5X_PCI_REG(0xd0c) : 0)
++#define PCI_BAR_REMAP_DDR_CS(n)	(((n) == 0) ? ORION5X_PCI_REG(0xc48) : \
++				 ((n) == 1) ? ORION5X_PCI_REG(0xd48) : \
++				 ((n) == 2) ? ORION5X_PCI_REG(0xc4c) : \
++				 ((n) == 3) ? ORION5X_PCI_REG(0xd4c) : 0)
+ #define PCI_BAR_ENABLE		ORION5X_PCI_REG(0xc3c)
+ #define PCI_ADDR_DECODE_CTRL	ORION5X_PCI_REG(0xd3c)
+ 
+--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
++++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
+@@ -125,6 +125,7 @@
+ 
+ 		leds_event = rd88f5182_dbgled_event;
+ 	}
++
+ 	return 0;
+ }
+ 
+@@ -234,7 +235,7 @@
+  * Sata
+  ****************************************************************************/
+ static struct mv_sata_platform_data rd88f5182_sata_data = {
+-	.n_ports        = 2,
++	.n_ports	= 2,
+ };
+ 
+ /*****************************************************************************
+--- a/arch/arm/mach-orion5x/ts209-setup.c
++++ b/arch/arm/mach-orion5x/ts209-setup.c
+@@ -47,52 +47,54 @@
+  ***************************************************************************/
+ static struct mtd_partition qnap_ts209_partitions[] = {
+ 	{
+-		.name       = "U-Boot",
+-		.size       = 0x00080000,
+-		.offset     = 0x00780000,
+-		.mask_flags = MTD_WRITEABLE,
++		.name		= "U-Boot",
++		.size		= 0x00080000,
++		.offset		= 0x00780000,
++		.mask_flags	= MTD_WRITEABLE,
+ 	}, {
+-		.name   = "Kernel",
+-		.size   = 0x00200000,
+-		.offset = 0,
++		.name		= "Kernel",
++		.size		= 0x00200000,
++		.offset		= 0,
+ 	}, {
+-		.name   = "RootFS1",
+-		.size   = 0x00400000,
+-		.offset = 0x00200000,
++		.name		= "RootFS1",
++		.size		= 0x00400000,
++		.offset		= 0x00200000,
+ 	}, {
+-		.name   = "RootFS2",
+-		.size   = 0x00100000,
+-		.offset = 0x00600000,
++		.name		= "RootFS2",
++		.size		= 0x00100000,
++		.offset		= 0x00600000,
+ 	}, {
+-		.name   = "U-Boot Config",
+-		.size   = 0x00020000,
+-		.offset = 0x00760000,
++		.name		= "U-Boot Config",
++		.size		= 0x00020000,
++		.offset		= 0x00760000,
+ 	}, {
+-		.name       = "NAS Config",
+-		.size       = 0x00060000,
+-		.offset     = 0x00700000,
+-		.mask_flags = MTD_WRITEABLE,
+-	}
++		.name		= "NAS Config",
++		.size		= 0x00060000,
++		.offset		= 0x00700000,
++		.mask_flags	= MTD_WRITEABLE,
++	},
+ };
+ 
+ static struct physmap_flash_data qnap_ts209_nor_flash_data = {
+-	.width    = 1,
+-	.parts    = qnap_ts209_partitions,
+-	.nr_parts = ARRAY_SIZE(qnap_ts209_partitions)
++	.width		= 1,
++	.parts		= qnap_ts209_partitions,
++	.nr_parts	= ARRAY_SIZE(qnap_ts209_partitions)
+ };
+ 
+ static struct resource qnap_ts209_nor_flash_resource = {
+-	.flags = IORESOURCE_MEM,
+-	.start = QNAP_TS209_NOR_BOOT_BASE,
+-	.end   = QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1,
++	.flags	= IORESOURCE_MEM,
++	.start	= QNAP_TS209_NOR_BOOT_BASE,
++	.end	= QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1,
+ };
+ 
+ static struct platform_device qnap_ts209_nor_flash = {
+-	.name          = "physmap-flash",
+-	.id            = 0,
+-	.dev           = { .platform_data = &qnap_ts209_nor_flash_data, },
+-	.resource      = &qnap_ts209_nor_flash_resource,
+-	.num_resources = 1,
++	.name		= "physmap-flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data	= &qnap_ts209_nor_flash_data,
++	},
++	.resource	= &qnap_ts209_nor_flash_resource,
++	.num_resources	= 1,
+ };
+ 
+ /*****************************************************************************
+@@ -164,12 +166,12 @@
+ }
+ 
+ static struct hw_pci qnap_ts209_pci __initdata = {
+-	.nr_controllers = 2,
+-	.preinit        = qnap_ts209_pci_preinit,
+-	.swizzle        = pci_std_swizzle,
+-	.setup          = orion5x_pci_sys_setup,
+-	.scan           = orion5x_pci_sys_scan_bus,
+-	.map_irq        = qnap_ts209_pci_map_irq,
++	.nr_controllers	= 2,
++	.preinit	= qnap_ts209_pci_preinit,
++	.swizzle	= pci_std_swizzle,
++	.setup		= orion5x_pci_sys_setup,
++	.scan		= orion5x_pci_sys_scan_bus,
++	.map_irq	= qnap_ts209_pci_map_irq,
+ };
+ 
+ static int __init qnap_ts209_pci_init(void)
+@@ -187,8 +189,8 @@
+  ****************************************************************************/
+ 
+ static struct mv643xx_eth_platform_data qnap_ts209_eth_data = {
+-	.phy_addr       = 8,
+-	.force_phy_addr = 1,
++	.phy_addr	= 8,
++	.force_phy_addr	= 1,
+ };
+ 
+ static int __init parse_hex_nibble(char n)
+@@ -280,7 +282,7 @@
+ 
+ static struct i2c_board_info __initdata qnap_ts209_i2c_rtc = {
+ 	I2C_BOARD_INFO("s35390a", 0x30),
+-       .irq         = 0,
++	.irq	= 0,
+ };
+ 
+ /****************************************************************************
+@@ -297,32 +299,33 @@
+ 		.gpio		= QNAP_TS209_GPIO_KEY_MEDIA,
+ 		.desc		= "USB Copy Button",
+ 		.active_low	= 1,
+-	},
+-	{
++	}, {
+ 		.code		= KEY_POWER,
+ 		.gpio		= QNAP_TS209_GPIO_KEY_RESET,
+ 		.desc		= "Reset Button",
+ 		.active_low	= 1,
+-	}
++	},
+ };
+ 
+ static struct gpio_keys_platform_data qnap_ts209_button_data = {
+ 	.buttons	= qnap_ts209_buttons,
+-	.nbuttons       = ARRAY_SIZE(qnap_ts209_buttons),
++	.nbuttons	= ARRAY_SIZE(qnap_ts209_buttons),
+ };
+ 
+ static struct platform_device qnap_ts209_button_device = {
+ 	.name		= "gpio-keys",
+ 	.id		= -1,
+ 	.num_resources	= 0,
+-	.dev		= { .platform_data  = &qnap_ts209_button_data, },
++	.dev		= {
++		.platform_data	= &qnap_ts209_button_data,
++	},
+ };
+ 
+ /*****************************************************************************
+  * SATA
+  ****************************************************************************/
+ static struct mv_sata_platform_data qnap_ts209_sata_data = {
+-	.n_ports        = 2,
++	.n_ports	= 2,
+ };
+ 
+ /*****************************************************************************
+@@ -339,7 +342,7 @@
+  * QNAP TS-[12]09 specific power off method via UART1-attached PIC
+  */
+ 
+-#define UART1_REG(x)  (UART1_VIRT_BASE + ((UART_##x) << 2))
++#define UART1_REG(x)	(UART1_VIRT_BASE + ((UART_##x) << 2))
+ 
+ static void qnap_ts209_power_off(void)
+ {
+@@ -372,7 +375,7 @@
+ 	 * Setup flash mapping
+ 	 */
+ 	orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE,
+-			    QNAP_TS209_NOR_BOOT_SIZE);
++				   QNAP_TS209_NOR_BOOT_SIZE);
+ 
+ 	/*
+ 	 * Open a special address decode windows for the PCIe WA.
+@@ -432,7 +435,7 @@
+ }
+ 
+ MACHINE_START(TS209, "QNAP TS-109/TS-209")
+-	/* Maintainer:  Byron Bradley <byron.bbradley@gmail.com> */
++	/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
+ 	.phys_io	= ORION5X_REGS_PHYS_BASE,
+ 	.io_pg_offst	= ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
+ 	.boot_params	= 0x00000100,
+--- a/arch/arm/mm/proc-feroceon.S
++++ b/arch/arm/mm/proc-feroceon.S
+@@ -454,13 +454,13 @@
+ __feroceon_old_id_proc_info:
+ 	.long	0x41069260
+ 	.long	0xfffffff0
+-	.long   PMD_TYPE_SECT | \
++	.long	PMD_TYPE_SECT | \
+ 		PMD_SECT_BUFFERABLE | \
+ 		PMD_SECT_CACHEABLE | \
+ 		PMD_BIT4 | \
+ 		PMD_SECT_AP_WRITE | \
+ 		PMD_SECT_AP_READ
+-	.long   PMD_TYPE_SECT | \
++	.long	PMD_TYPE_SECT | \
+ 		PMD_BIT4 | \
+ 		PMD_SECT_AP_WRITE | \
+ 		PMD_SECT_AP_READ
+@@ -480,13 +480,13 @@
+ __feroceon_proc_info:
+ 	.long	0x56055310
+ 	.long	0xfffffff0
+-	.long   PMD_TYPE_SECT | \
++	.long	PMD_TYPE_SECT | \
+ 		PMD_SECT_BUFFERABLE | \
+ 		PMD_SECT_CACHEABLE | \
+ 		PMD_BIT4 | \
+ 		PMD_SECT_AP_WRITE | \
+ 		PMD_SECT_AP_READ
+-	.long   PMD_TYPE_SECT | \
++	.long	PMD_TYPE_SECT | \
+ 		PMD_BIT4 | \
+ 		PMD_SECT_AP_WRITE | \
+ 		PMD_SECT_AP_READ
diff --git a/target/linux/orion/patches/004-make_window_setup_a_little_more_safe.patch b/target/linux/orion/patches/004-make_window_setup_a_little_more_safe.patch
new file mode 100644
index 0000000..f5f1de4
--- /dev/null
+++ b/target/linux/orion/patches/004-make_window_setup_a_little_more_safe.patch
@@ -0,0 +1,79 @@
+Currently, Orion window setup uses hardcoded window indexes for each
+of the boot/cs0/cs1/cs2/PCIe WA windows.  The static window allocation
+used can clash if board support code will ever attempt to configure
+both a dev2 and a PCIe WA window, as both of those use CPU mbus window
+#7 at present.
+
+This patch keeps track of the last used window, and opens subsequently
+requested windows sequentially, starting from 4.  (Windows 0-3 are used
+as MEM/IO windows for the PCI/PCIe buses.)
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/addr-map.c |   20 +++++++++++++++-----
+ 1 files changed, 15 insertions(+), 5 deletions(-)
+
+--- a/arch/arm/mach-orion5x/addr-map.c
++++ b/arch/arm/mach-orion5x/addr-map.c
+@@ -70,6 +70,7 @@
+ 
+ 
+ struct mbus_dram_target_info orion5x_mbus_dram_info;
++static int __initdata win_alloc_count;
+ 
+ static int __init orion5x_cpu_win_can_remap(int win)
+ {
+@@ -87,6 +88,9 @@
+ static void __init setup_cpu_win(int win, u32 base, u32 size,
+ 				 u8 target, u8 attr, int remap)
+ {
++	if (win >= 8)
++		panic("setup_cpu_win: trying to allocate window %d\n", win);
++
+ 	orion5x_write(CPU_WIN_BASE(win), base & 0xffff0000);
+ 	orion5x_write(CPU_WIN_CTRL(win),
+ 		((size - 1) & 0xffff0000) | (attr << 8) | (target << 4) | 1);
+@@ -128,6 +132,7 @@
+ 		TARGET_PCIE, ATTR_PCIE_MEM, -1);
+ 	setup_cpu_win(3, ORION5X_PCI_MEM_PHYS_BASE, ORION5X_PCI_MEM_SIZE,
+ 		TARGET_PCI, ATTR_PCI_MEM, -1);
++	win_alloc_count = 4;
+ 
+ 	/*
+ 	 * Setup MBUS dram target info.
+@@ -156,25 +161,30 @@
+ 
+ void __init orion5x_setup_dev_boot_win(u32 base, u32 size)
+ {
+-	setup_cpu_win(4, base, size, TARGET_DEV_BUS, ATTR_DEV_BOOT, -1);
++	setup_cpu_win(win_alloc_count++, base, size,
++		      TARGET_DEV_BUS, ATTR_DEV_BOOT, -1);
+ }
+ 
+ void __init orion5x_setup_dev0_win(u32 base, u32 size)
+ {
+-	setup_cpu_win(5, base, size, TARGET_DEV_BUS, ATTR_DEV_CS0, -1);
++	setup_cpu_win(win_alloc_count++, base, size,
++		      TARGET_DEV_BUS, ATTR_DEV_CS0, -1);
+ }
+ 
+ void __init orion5x_setup_dev1_win(u32 base, u32 size)
+ {
+-	setup_cpu_win(6, base, size, TARGET_DEV_BUS, ATTR_DEV_CS1, -1);
++	setup_cpu_win(win_alloc_count++, base, size,
++		      TARGET_DEV_BUS, ATTR_DEV_CS1, -1);
+ }
+ 
+ void __init orion5x_setup_dev2_win(u32 base, u32 size)
+ {
+-	setup_cpu_win(7, base, size, TARGET_DEV_BUS, ATTR_DEV_CS2, -1);
++	setup_cpu_win(win_alloc_count++, base, size,
++		      TARGET_DEV_BUS, ATTR_DEV_CS2, -1);
+ }
+ 
+ void __init orion5x_setup_pcie_wa_win(u32 base, u32 size)
+ {
+-	setup_cpu_win(7, base, size, TARGET_PCIE, ATTR_PCIE_WA, -1);
++	setup_cpu_win(win_alloc_count++, base, size,
++		      TARGET_PCIE, ATTR_PCIE_WA, -1);
+ }
diff --git a/target/linux/orion/patches/005-dram_mapping_granularity_is_64kib.patch b/target/linux/orion/patches/005-dram_mapping_granularity_is_64kib.patch
new file mode 100644
index 0000000..2e7815d
--- /dev/null
+++ b/target/linux/orion/patches/005-dram_mapping_granularity_is_64kib.patch
@@ -0,0 +1,26 @@
+The DRAM base address and size fields in the CPU's MBUS bridge have
+64KiB granularity, instead of the currently used 16MiB.  Since all
+of the currently supported MBUS peripherals support 64KiB granularity
+as well, this patch changes the Orion address map code to stop
+rounding base addresses down and sizes up to multiples of 16MiB.
+
+Found by Ke Wei <kewei@marvell.com>.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/addr-map.c |    4 ++--
+ 1 files changed, 2 insertions(+), 2 deletions(-)
+
+--- a/arch/arm/mach-orion5x/addr-map.c
++++ b/arch/arm/mach-orion5x/addr-map.c
+@@ -152,8 +152,8 @@
+ 			w = &orion5x_mbus_dram_info.cs[cs++];
+ 			w->cs_index = i;
+ 			w->mbus_attr = 0xf & ~(1 << i);
+-			w->base = base & 0xff000000;
+-			w->size = (size | 0x00ffffff) + 1;
++			w->base = base & 0xffff0000;
++			w->size = (size | 0x0000ffff) + 1;
+ 		}
+ 	}
+ 	orion5x_mbus_dram_info.num_cs = cs;
diff --git a/target/linux/orion/patches/006-add_a_separate_BRIDGE_INT_TIMER1_CLR_define.patch b/target/linux/orion/patches/006-add_a_separate_BRIDGE_INT_TIMER1_CLR_define.patch
new file mode 100644
index 0000000..75daedd
--- /dev/null
+++ b/target/linux/orion/patches/006-add_a_separate_BRIDGE_INT_TIMER1_CLR_define.patch
@@ -0,0 +1,37 @@
+From: Ke Wei <kewei@marvell.com>
+
+Some Feroceon-based SoCs have an MBUS bridge interrupt controller
+that requires writing a one instead of a zero to clear edge
+interrupt sources such as timer expiry.
+
+This patch adds a new BRIDGE_INT_TIMER1_CLR define, which platform
+code can set to either ~BRIDGE_INT_TIMER1 (write-zero-to-clear) or
+BRIDGE_INT_TIMER1 (write-one-to-clear) depending on the platform.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/plat-orion/time.c             |    2 +-
+ include/asm-arm/arch-orion5x/orion5x.h |    1 +
+ 2 files changed, 2 insertions(+), 1 deletions(-)
+
+--- a/arch/arm/plat-orion/time.c
++++ b/arch/arm/plat-orion/time.c
+@@ -74,7 +74,7 @@
+ 	/*
+ 	 * Clear and enable clockevent timer interrupt.
+ 	 */
+-	writel(~BRIDGE_INT_TIMER1, BRIDGE_CAUSE);
++	writel(BRIDGE_INT_TIMER1_CLR, BRIDGE_CAUSE);
+ 
+ 	u = readl(BRIDGE_MASK);
+ 	u |= BRIDGE_INT_TIMER1;
+--- a/include/asm-arm/arch-orion5x/orion5x.h
++++ b/include/asm-arm/arch-orion5x/orion5x.h
+@@ -152,6 +152,7 @@
+ #define BRIDGE_MASK		ORION5X_BRIDGE_REG(0x114)
+ #define  BRIDGE_INT_TIMER0	0x0002
+ #define  BRIDGE_INT_TIMER1	0x0004
++#define  BRIDGE_INT_TIMER1_CLR	~0x0004
+ #define MAIN_IRQ_CAUSE		ORION5X_BRIDGE_REG(0x200)
+ #define MAIN_IRQ_MASK		ORION5X_BRIDGE_REG(0x204)
+ 
diff --git a/target/linux/orion/patches/007-annotate_88fr531-vd_cpu_entries.patch b/target/linux/orion/patches/007-annotate_88fr531-vd_cpu_entries.patch
new file mode 100644
index 0000000..5aab94b
--- /dev/null
+++ b/target/linux/orion/patches/007-annotate_88fr531-vd_cpu_entries.patch
@@ -0,0 +1,58 @@
+Annotate the entries for the 88fr531-vd CPU core in
+arch/arm/boot/compressed/head.S and arch/arm/mm/proc-feroceon.S
+with the full name of the core.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/boot/compressed/head.S |    2 +-
+ arch/arm/mm/proc-feroceon.S     |   13 +++++++++----
+ 2 files changed, 10 insertions(+), 5 deletions(-)
+
+--- a/arch/arm/boot/compressed/head.S
++++ b/arch/arm/boot/compressed/head.S
+@@ -623,7 +623,7 @@
+ 		b	__armv4_mmu_cache_off
+ 		b	__armv4_mmu_cache_flush
+ 
+-		.word	0x56055310		@ Feroceon
++		.word	0x56055310		@ Feroceon 88FR531-vd
+ 		.word	0xfffffff0
+ 		b	__armv4_mmu_cache_on
+ 		b	__armv4_mmu_cache_off
+--- a/arch/arm/mm/proc-feroceon.S
++++ b/arch/arm/mm/proc-feroceon.S
+@@ -445,6 +445,11 @@
+ 	.asciz	"Feroceon"
+ 	.size	cpu_feroceon_name, . - cpu_feroceon_name
+ 
++	.type	cpu_88fr531_name, #object
++cpu_88fr531_name:
++	.asciz	"Feroceon 88FR531-vd"
++	.size	cpu_88fr531_name, . - cpu_88fr531_name
++
+ 	.align
+ 
+ 	.section ".proc.info.init", #alloc, #execinstr
+@@ -476,8 +481,8 @@
+ 	.size	__feroceon_old_id_proc_info, . - __feroceon_old_id_proc_info
+ #endif
+ 
+-	.type	__feroceon_proc_info,#object
+-__feroceon_proc_info:
++	.type	__88fr531_proc_info,#object
++__88fr531_proc_info:
+ 	.long	0x56055310
+ 	.long	0xfffffff0
+ 	.long	PMD_TYPE_SECT | \
+@@ -494,9 +499,9 @@
+ 	.long	cpu_arch_name
+ 	.long	cpu_elf_name
+ 	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP
+-	.long	cpu_feroceon_name
++	.long	cpu_88fr531_name
+ 	.long	feroceon_processor_functions
+ 	.long	v4wbi_tlb_fns
+ 	.long	feroceon_user_fns
+ 	.long	feroceon_cache_fns
+-	.size	__feroceon_proc_info, . - __feroceon_proc_info
++	.size	__88fr531_proc_info, . - __88fr531_proc_info
diff --git a/target/linux/orion/patches/008-top-level_irqs_are_level-triggered.patch b/target/linux/orion/patches/008-top-level_irqs_are_level-triggered.patch
new file mode 100644
index 0000000..add1590
--- /dev/null
+++ b/target/linux/orion/patches/008-top-level_irqs_are_level-triggered.patch
@@ -0,0 +1,35 @@
+Make it clear that Orion top-level IRQs are level-triggered.  This
+means that we don't need an ->ack() handler, or at least, we don't
+need the ->ack() handler (or the acking part of the ->mask_ack()
+handler) to actually do anything.
+
+Given that, we might as well point our ->mask_ack() handler at the
+->mask() handler instead of providing a dummy ->ack() handler, since
+providing a ->mask_ack() handler on level IRQ sources will prevent
+->ack() from ever being called.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/plat-orion/irq.c |    3 ++-
+ 1 files changed, 2 insertions(+), 1 deletions(-)
+
+--- a/arch/arm/plat-orion/irq.c
++++ b/arch/arm/plat-orion/irq.c
+@@ -36,8 +36,8 @@
+ 
+ static struct irq_chip orion_irq_chip = {
+ 	.name		= "orion_irq",
+-	.ack		= orion_irq_mask,
+ 	.mask		= orion_irq_mask,
++	.mask_ack	= orion_irq_mask,
+ 	.unmask		= orion_irq_unmask,
+ };
+ 
+@@ -59,6 +59,7 @@
+ 		set_irq_chip(irq, &orion_irq_chip);
+ 		set_irq_chip_data(irq, maskaddr);
+ 		set_irq_handler(irq, handle_level_irq);
++		irq_desc[irq].status |= IRQ_LEVEL;
+ 		set_irq_flags(irq, IRQF_VALID);
+ 	}
+ }
diff --git a/target/linux/orion/patches/009-delete_unused_IO_SPACE_REMAP_define.patch b/target/linux/orion/patches/009-delete_unused_IO_SPACE_REMAP_define.patch
new file mode 100644
index 0000000..222a6da
--- /dev/null
+++ b/target/linux/orion/patches/009-delete_unused_IO_SPACE_REMAP_define.patch
@@ -0,0 +1,17 @@
+This define isn't used anywhere in the kernel tree -- nuke it.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ include/asm-arm/arch-orion5x/io.h |    1 -
+ 1 files changed, 0 insertions(+), 1 deletions(-)
+
+--- a/include/asm-arm/arch-orion5x/io.h
++++ b/include/asm-arm/arch-orion5x/io.h
+@@ -14,7 +14,6 @@
+ #include "orion5x.h"
+ 
+ #define IO_SPACE_LIMIT		0xffffffff
+-#define IO_SPACE_REMAP		ORION5X_PCI_SYS_IO_BASE
+ 
+ static inline void __iomem *
+ __arch_ioremap(unsigned long paddr, size_t size, unsigned int mtype)
diff --git a/target/linux/orion/patches/010-move_EHCI_I2C_UART_peripheral_init.patch b/target/linux/orion/patches/010-move_EHCI_I2C_UART_peripheral_init.patch
new file mode 100644
index 0000000..6f11eef
--- /dev/null
+++ b/target/linux/orion/patches/010-move_EHCI_I2C_UART_peripheral_init.patch
@@ -0,0 +1,710 @@
+This patch moves initialisation of EHCI/I2C/UART platform devices
+from the common orion5x_init() into the board support code.
+
+The rationale behind this is that only the board support code knows
+whether certain peripherals have been brought out on the board, and
+not initialising peripherals that haven't been brought out is
+desirable for example:
+- to reduce user confusion (e.g. seeing both 'eth0' and 'eth1'
+  appear while there is only one ethernet port on the board); and
+- to allow for future power savings (peripherals that have not
+  been brought out can be clock gated off entirely.)
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/common.c            |  226 +++++++++++++++++------------
+ arch/arm/mach-orion5x/common.h            |   35 ++---
+ arch/arm/mach-orion5x/db88f5281-setup.c   |   39 +++---
+ arch/arm/mach-orion5x/dns323-setup.c      |   40 +++---
+ arch/arm/mach-orion5x/kurobox_pro-setup.c |   28 +++--
+ arch/arm/mach-orion5x/rd88f5182-setup.c   |   29 ++--
+ arch/arm/mach-orion5x/ts209-setup.c       |   38 ++---
+ 7 files changed, 240 insertions(+), 195 deletions(-)
+
+--- a/arch/arm/mach-orion5x/common.c
++++ b/arch/arm/mach-orion5x/common.c
+@@ -63,65 +63,20 @@
+ 	iotable_init(orion5x_io_desc, ARRAY_SIZE(orion5x_io_desc));
+ }
+ 
++
+ /*****************************************************************************
+- * UART
++ * EHCI
+  ****************************************************************************/
+-
+-static struct resource orion5x_uart_resources[] = {
+-	{
+-		.start		= UART0_PHYS_BASE,
+-		.end		= UART0_PHYS_BASE + 0xff,
+-		.flags		= IORESOURCE_MEM,
+-	}, {
+-		.start		= IRQ_ORION5X_UART0,
+-		.end		= IRQ_ORION5X_UART0,
+-		.flags		= IORESOURCE_IRQ,
+-	}, {
+-		.start		= UART1_PHYS_BASE,
+-		.end		= UART1_PHYS_BASE + 0xff,
+-		.flags		= IORESOURCE_MEM,
+-	}, {
+-		.start		= IRQ_ORION5X_UART1,
+-		.end		= IRQ_ORION5X_UART1,
+-		.flags		= IORESOURCE_IRQ,
+-	},
+-};
+-
+-static struct plat_serial8250_port orion5x_uart_data[] = {
+-	{
+-		.mapbase	= UART0_PHYS_BASE,
+-		.membase	= (char *)UART0_VIRT_BASE,
+-		.irq		= IRQ_ORION5X_UART0,
+-		.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
+-		.iotype		= UPIO_MEM,
+-		.regshift	= 2,
+-		.uartclk	= ORION5X_TCLK,
+-	}, {
+-		.mapbase	= UART1_PHYS_BASE,
+-		.membase	= (char *)UART1_VIRT_BASE,
+-		.irq		= IRQ_ORION5X_UART1,
+-		.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
+-		.iotype		= UPIO_MEM,
+-		.regshift	= 2,
+-		.uartclk	= ORION5X_TCLK,
+-	}, {
+-	},
++static struct orion_ehci_data orion5x_ehci_data = {
++	.dram		= &orion5x_mbus_dram_info,
+ };
+ 
+-static struct platform_device orion5x_uart = {
+-	.name			= "serial8250",
+-	.id			= PLAT8250_DEV_PLATFORM,
+-	.dev			= {
+-		.platform_data	= orion5x_uart_data,
+-	},
+-	.resource		= orion5x_uart_resources,
+-	.num_resources		= ARRAY_SIZE(orion5x_uart_resources),
+-};
++static u64 ehci_dmamask = 0xffffffffUL;
+ 
+-/*******************************************************************************
+- * USB Controller - 2 interfaces
+- ******************************************************************************/
+ 
++/*****************************************************************************
++ * EHCI0
++ ****************************************************************************/
+ static struct resource orion5x_ehci0_resources[] = {
+ 	{
+ 		.start	= ORION5X_USB0_PHYS_BASE,
+@@ -134,24 +89,6 @@
+ 	},
+ };
+ 
+-static struct resource orion5x_ehci1_resources[] = {
+-	{
+-		.start	= ORION5X_USB1_PHYS_BASE,
+-		.end	= ORION5X_USB1_PHYS_BASE + SZ_4K - 1,
+-		.flags	= IORESOURCE_MEM,
+-	}, {
+-		.start	= IRQ_ORION5X_USB1_CTRL,
+-		.end	= IRQ_ORION5X_USB1_CTRL,
+-		.flags	= IORESOURCE_IRQ,
+-	},
+-};
+-
+-static struct orion_ehci_data orion5x_ehci_data = {
+-	.dram		= &orion5x_mbus_dram_info,
+-};
+-
+-static u64 ehci_dmamask = 0xffffffffUL;
+-
+ static struct platform_device orion5x_ehci0 = {
+ 	.name		= "orion-ehci",
+ 	.id		= 0,
+@@ -164,6 +101,27 @@
+ 	.num_resources	= ARRAY_SIZE(orion5x_ehci0_resources),
+ };
+ 
++void __init orion5x_ehci0_init(void)
++{
++	platform_device_register(&orion5x_ehci0);
++}
++
++
++/*****************************************************************************
++ * EHCI1
++ ****************************************************************************/
++static struct resource orion5x_ehci1_resources[] = {
++	{
++		.start	= ORION5X_USB1_PHYS_BASE,
++		.end	= ORION5X_USB1_PHYS_BASE + SZ_4K - 1,
++		.flags	= IORESOURCE_MEM,
++	}, {
++		.start	= IRQ_ORION5X_USB1_CTRL,
++		.end	= IRQ_ORION5X_USB1_CTRL,
++		.flags	= IORESOURCE_IRQ,
++	},
++};
++
+ static struct platform_device orion5x_ehci1 = {
+ 	.name		= "orion-ehci",
+ 	.id		= 1,
+@@ -176,11 +134,15 @@
+ 	.num_resources	= ARRAY_SIZE(orion5x_ehci1_resources),
+ };
+ 
++void __init orion5x_ehci1_init(void)
++{
++	platform_device_register(&orion5x_ehci1);
++}
++
++
+ /*****************************************************************************
+- * Gigabit Ethernet port
+- * (The Orion and Discovery (MV643xx) families use the same Ethernet driver)
++ * GigE
+  ****************************************************************************/
+-
+ struct mv643xx_eth_shared_platform_data orion5x_eth_shared_data = {
+ 	.dram		= &orion5x_mbus_dram_info,
+ 	.t_clk		= ORION5X_TCLK,
+@@ -229,11 +191,10 @@
+ 	platform_device_register(&orion5x_eth);
+ }
+ 
++
+ /*****************************************************************************
+- * I2C controller
+- * (The Orion and Discovery (MV643xx) families share the same I2C controller)
++ * I2C
+  ****************************************************************************/
+-
+ static struct mv64xxx_i2c_pdata orion5x_i2c_pdata = {
+ 	.freq_m		= 8, /* assumes 166 MHz TCLK */
+ 	.freq_n		= 3,
+@@ -244,7 +205,7 @@
+ 	{
+ 		.name	= "i2c base",
+ 		.start	= I2C_PHYS_BASE,
+-		.end	= I2C_PHYS_BASE + 0x20 -1,
++		.end	= I2C_PHYS_BASE + 0x1f,
+ 		.flags	= IORESOURCE_MEM,
+ 	}, {
+ 		.name	= "i2c irq",
+@@ -264,8 +225,14 @@
+ 	},
+ };
+ 
++void __init orion5x_i2c_init(void)
++{
++	platform_device_register(&orion5x_i2c);
++}
++
++
+ /*****************************************************************************
+- * Sata port
++ * SATA
+  ****************************************************************************/
+ static struct resource orion5x_sata_resources[] = {
+ 	{
+@@ -298,10 +265,98 @@
+ 	platform_device_register(&orion5x_sata);
+ }
+ 
++
+ /*****************************************************************************
+- * Time handling
++ * UART0
++ ****************************************************************************/
++static struct plat_serial8250_port orion5x_uart0_data[] = {
++	{
++		.mapbase	= UART0_PHYS_BASE,
++		.membase	= (char *)UART0_VIRT_BASE,
++		.irq		= IRQ_ORION5X_UART0,
++		.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= ORION5X_TCLK,
++	}, {
++	},
++};
++
++static struct resource orion5x_uart0_resources[] = {
++	{
++		.start		= UART0_PHYS_BASE,
++		.end		= UART0_PHYS_BASE + 0xff,
++		.flags		= IORESOURCE_MEM,
++	}, {
++		.start		= IRQ_ORION5X_UART0,
++		.end		= IRQ_ORION5X_UART0,
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device orion5x_uart0 = {
++	.name			= "serial8250",
++	.id			= PLAT8250_DEV_PLATFORM,
++	.dev			= {
++		.platform_data	= orion5x_uart0_data,
++	},
++	.resource		= orion5x_uart0_resources,
++	.num_resources		= ARRAY_SIZE(orion5x_uart0_resources),
++};
++
++void __init orion5x_uart0_init(void)
++{
++	platform_device_register(&orion5x_uart0);
++}
++
++
++/*****************************************************************************
++ * UART1
+  ****************************************************************************/
++static struct plat_serial8250_port orion5x_uart1_data[] = {
++	{
++		.mapbase	= UART1_PHYS_BASE,
++		.membase	= (char *)UART1_VIRT_BASE,
++		.irq		= IRQ_ORION5X_UART1,
++		.flags		= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF,
++		.iotype		= UPIO_MEM,
++		.regshift	= 2,
++		.uartclk	= ORION5X_TCLK,
++	}, {
++	},
++};
++
++static struct resource orion5x_uart1_resources[] = {
++	{
++		.start		= UART1_PHYS_BASE,
++		.end		= UART1_PHYS_BASE + 0xff,
++		.flags		= IORESOURCE_MEM,
++	}, {
++		.start		= IRQ_ORION5X_UART1,
++		.end		= IRQ_ORION5X_UART1,
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++static struct platform_device orion5x_uart1 = {
++	.name			= "serial8250",
++	.id			= PLAT8250_DEV_PLATFORM1,
++	.dev			= {
++		.platform_data	= orion5x_uart1_data,
++	},
++	.resource		= orion5x_uart1_resources,
++	.num_resources		= ARRAY_SIZE(orion5x_uart1_resources),
++};
++
++void __init orion5x_uart1_init(void)
++{
++	platform_device_register(&orion5x_uart1);
++}
+ 
++
++/*****************************************************************************
++ * Time handling
++ ****************************************************************************/
+ static void orion5x_timer_init(void)
+ {
+ 	orion_time_init(IRQ_ORION5X_BRIDGE, ORION5X_TCLK);
+@@ -311,10 +366,10 @@
+ 	.init = orion5x_timer_init,
+ };
+ 
++
+ /*****************************************************************************
+  * General
+  ****************************************************************************/
+-
+ /*
+  * Identify device ID and rev from PCIe configuration header space '0'.
+  */
+@@ -359,15 +414,6 @@
+ 	 * Setup Orion address map
+ 	 */
+ 	orion5x_setup_cpu_mbus_bridge();
+-
+-	/*
+-	 * Register devices.
+-	 */
+-	platform_device_register(&orion5x_uart);
+-	platform_device_register(&orion5x_ehci0);
+-	if (dev == MV88F5182_DEV_ID)
+-		platform_device_register(&orion5x_ehci1);
+-	platform_device_register(&orion5x_i2c);
+ }
+ 
+ /*
+--- a/arch/arm/mach-orion5x/common.h
++++ b/arch/arm/mach-orion5x/common.h
+@@ -1,10 +1,12 @@
+ #ifndef __ARCH_ORION5X_COMMON_H
+ #define __ARCH_ORION5X_COMMON_H
+ 
++struct mv643xx_eth_platform_data;
++struct mv_sata_platform_data;
++
+ /*
+  * Basic Orion init functions used early by machine-setup.
+  */
+-
+ void orion5x_map_io(void);
+ void orion5x_init_irq(void);
+ void orion5x_init(void);
+@@ -23,13 +25,19 @@
+ void orion5x_setup_dev2_win(u32 base, u32 size);
+ void orion5x_setup_pcie_wa_win(u32 base, u32 size);
+ 
++void orion5x_ehci0_init(void);
++void orion5x_ehci1_init(void);
++void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data);
++void orion5x_i2c_init(void);
++void orion5x_sata_init(struct mv_sata_platform_data *sata_data);
++void orion5x_uart0_init(void);
++void orion5x_uart1_init(void);
++
+ /*
+- * Shared code used internally by other Orion core functions.
+- * (/mach-orion/pci.c)
++ * PCIe/PCI functions.
+  */
+-
+-struct pci_sys_data;
+ struct pci_bus;
++struct pci_sys_data;
+ 
+ void orion5x_pcie_id(u32 *dev, u32 *rev);
+ int orion5x_pci_sys_setup(int nr, struct pci_sys_data *sys);
+@@ -40,26 +48,9 @@
+  * Valid GPIO pins according to MPP setup, used by machine-setup.
+  * (/mach-orion/gpio.c).
+  */
+-
+ void orion5x_gpio_set_valid_pins(u32 pins);
+ void gpio_display(void);	/* debug */
+ 
+-/*
+- * Pull in Orion Ethernet platform_data, used by machine-setup
+- */
+-
+-struct mv643xx_eth_platform_data;
+-
+-void orion5x_eth_init(struct mv643xx_eth_platform_data *eth_data);
+-
+-/*
+- * Orion Sata platform_data, used by machine-setup
+- */
+-
+-struct mv_sata_platform_data;
+-
+-void orion5x_sata_init(struct mv_sata_platform_data *sata_data);
+-
+ struct machine_desc;
+ struct meminfo;
+ struct tag;
+--- a/arch/arm/mach-orion5x/db88f5281-setup.c
++++ b/arch/arm/mach-orion5x/db88f5281-setup.c
+@@ -298,13 +298,6 @@
+ /*****************************************************************************
+  * General Setup
+  ****************************************************************************/
+-
+-static struct platform_device *db88f5281_devs[] __initdata = {
+-	&db88f5281_boot_flash,
+-	&db88f5281_nor_flash,
+-	&db88f5281_nand_flash,
+-};
+-
+ static void __init db88f5281_init(void)
+ {
+ 	/*
+@@ -313,15 +306,6 @@
+ 	orion5x_init();
+ 
+ 	/*
+-	 * Setup the CPU address decode windows for our on-board devices
+-	 */
+-	orion5x_setup_dev_boot_win(DB88F5281_NOR_BOOT_BASE,
+-				DB88F5281_NOR_BOOT_SIZE);
+-	orion5x_setup_dev0_win(DB88F5281_7SEG_BASE, DB88F5281_7SEG_SIZE);
+-	orion5x_setup_dev1_win(DB88F5281_NOR_BASE, DB88F5281_NOR_SIZE);
+-	orion5x_setup_dev2_win(DB88F5281_NAND_BASE, DB88F5281_NAND_SIZE);
+-
+-	/*
+ 	 * Setup Multiplexing Pins:
+ 	 * MPP0: GPIO (USB Over Current)	MPP1: GPIO (USB Vbat input)
+ 	 * MPP2: PCI_REQn[2]			MPP3: PCI_GNTn[2]
+@@ -342,9 +326,28 @@
+ 
+ 	orion5x_gpio_set_valid_pins(0x00003fc3);
+ 
+-	platform_add_devices(db88f5281_devs, ARRAY_SIZE(db88f5281_devs));
+-	i2c_register_board_info(0, &db88f5281_i2c_rtc, 1);
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
+ 	orion5x_eth_init(&db88f5281_eth_data);
++	orion5x_i2c_init();
++	orion5x_uart0_init();
++	orion5x_uart1_init();
++
++	orion5x_setup_dev_boot_win(DB88F5281_NOR_BOOT_BASE,
++				DB88F5281_NOR_BOOT_SIZE);
++	platform_device_register(&db88f5281_boot_flash);
++
++	orion5x_setup_dev0_win(DB88F5281_7SEG_BASE, DB88F5281_7SEG_SIZE);
++
++	orion5x_setup_dev1_win(DB88F5281_NOR_BASE, DB88F5281_NOR_SIZE);
++	platform_device_register(&db88f5281_nor_flash);
++
++	orion5x_setup_dev2_win(DB88F5281_NAND_BASE, DB88F5281_NAND_SIZE);
++	platform_device_register(&db88f5281_nand_flash);
++
++	i2c_register_board_info(0, &db88f5281_i2c_rtc, 1);
+ }
+ 
+ MACHINE_START(DB88F5281, "Marvell Orion-2 Development Board")
+--- a/arch/arm/mach-orion5x/dns323-setup.c
++++ b/arch/arm/mach-orion5x/dns323-setup.c
+@@ -213,12 +213,6 @@
+  * General Setup
+  */
+ 
+-static struct platform_device *dns323_plat_devices[] __initdata = {
+-	&dns323_nor_flash,
+-	&dns323_gpio_leds,
+-	&dns323_button_device,
+-};
+-
+ /*
+  * On the DNS-323 the following devices are attached via I2C:
+  *
+@@ -253,11 +247,6 @@
+ 	/* Setup basic Orion functions. Need to be called early. */
+ 	orion5x_init();
+ 
+-	/* setup flash mapping
+-	 * CS3 holds a 8 MB Spansion S29GL064M90TFIR4
+-	 */
+-	orion5x_setup_dev_boot_win(DNS323_NOR_BOOT_BASE, DNS323_NOR_BOOT_SIZE);
+-
+ 	/* DNS-323 has a Marvell 88X7042 SATA controller attached via PCIe
+ 	 *
+ 	 * Open a special address decode windows for the PCIe WA.
+@@ -294,21 +283,32 @@
+ 	*/
+ 	orion5x_gpio_set_valid_pins(0x07f6);
+ 
+-	/* register dns323 specific power-off method */
+-	if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 ||
+-	    gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0)
+-		pr_err("DNS323: failed to setup power-off GPIO\n");
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	orion5x_eth_init(&dns323_eth_data);
++	orion5x_i2c_init();
++	orion5x_uart0_init();
+ 
+-	pm_power_off = dns323_power_off;
++	/* setup flash mapping
++	 * CS3 holds a 8 MB Spansion S29GL064M90TFIR4
++	 */
++	orion5x_setup_dev_boot_win(DNS323_NOR_BOOT_BASE, DNS323_NOR_BOOT_SIZE);
++	platform_device_register(&dns323_nor_flash);
++
++	platform_device_register(&dns323_gpio_leds);
+ 
+-	/* register flash and other platform devices */
+-	platform_add_devices(dns323_plat_devices,
+-			     ARRAY_SIZE(dns323_plat_devices));
++	platform_device_register(&dns323_button_device);
+ 
+ 	i2c_register_board_info(0, dns323_i2c_devices,
+ 				ARRAY_SIZE(dns323_i2c_devices));
+ 
+-	orion5x_eth_init(&dns323_eth_data);
++	/* register dns323 specific power-off method */
++	if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 ||
++	    gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0)
++		pr_err("DNS323: failed to setup power-off GPIO\n");
++	pm_power_off = dns323_power_off;
+ }
+ 
+ /* Warning: D-Link uses a wrong mach-type (=526) in their bootloader */
+--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
++++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
+@@ -188,13 +188,6 @@
+ 	orion5x_init();
+ 
+ 	/*
+-	 * Setup the CPU address decode windows for our devices
+-	 */
+-	orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
+-				KUROBOX_PRO_NOR_BOOT_SIZE);
+-	orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE, KUROBOX_PRO_NAND_SIZE);
+-
+-	/*
+ 	 * Open a special address decode windows for the PCIe WA.
+ 	 */
+ 	orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
+@@ -221,12 +214,27 @@
+ 
+ 	orion5x_gpio_set_valid_pins(0x0000000c);
+ 
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	orion5x_ehci1_init();
++	orion5x_eth_init(&kurobox_pro_eth_data);
++	orion5x_i2c_init();
++	orion5x_sata_init(&kurobox_pro_sata_data);
++	orion5x_uart0_init();
++
++	orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
++				   KUROBOX_PRO_NOR_BOOT_SIZE);
+ 	platform_device_register(&kurobox_pro_nor_flash);
+-	if (machine_is_kurobox_pro())
++
++	if (machine_is_kurobox_pro()) {
++		orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE,
++				       KUROBOX_PRO_NAND_SIZE);
+ 		platform_device_register(&kurobox_pro_nand_flash);
++	}
++
+ 	i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);
+-	orion5x_eth_init(&kurobox_pro_eth_data);
+-	orion5x_sata_init(&kurobox_pro_sata_data);
+ }
+ 
+ #ifdef CONFIG_MACH_KUROBOX_PRO
+--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
++++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
+@@ -241,11 +241,6 @@
+ /*****************************************************************************
+  * General Setup
+  ****************************************************************************/
+-
+-static struct platform_device *rd88f5182_devices[] __initdata = {
+-	&rd88f5182_nor_flash,
+-};
+-
+ static void __init rd88f5182_init(void)
+ {
+ 	/*
+@@ -254,13 +249,6 @@
+ 	orion5x_init();
+ 
+ 	/*
+-	 * Setup the CPU address decode windows for our devices
+-	 */
+-	orion5x_setup_dev_boot_win(RD88F5182_NOR_BOOT_BASE,
+-				RD88F5182_NOR_BOOT_SIZE);
+-	orion5x_setup_dev1_win(RD88F5182_NOR_BASE, RD88F5182_NOR_SIZE);
+-
+-	/*
+ 	 * Open a special address decode windows for the PCIe WA.
+ 	 */
+ 	orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
+@@ -296,10 +284,23 @@
+ 
+ 	orion5x_gpio_set_valid_pins(0x000000fb);
+ 
+-	platform_add_devices(rd88f5182_devices, ARRAY_SIZE(rd88f5182_devices));
+-	i2c_register_board_info(0, &rd88f5182_i2c_rtc, 1);
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	orion5x_ehci1_init();
+ 	orion5x_eth_init(&rd88f5182_eth_data);
++	orion5x_i2c_init();
+ 	orion5x_sata_init(&rd88f5182_sata_data);
++	orion5x_uart0_init();
++
++	orion5x_setup_dev_boot_win(RD88F5182_NOR_BOOT_BASE,
++				   RD88F5182_NOR_BOOT_SIZE);
++
++	orion5x_setup_dev1_win(RD88F5182_NOR_BASE, RD88F5182_NOR_SIZE);
++	platform_device_register(&rd88f5182_nor_flash);
++
++	i2c_register_board_info(0, &rd88f5182_i2c_rtc, 1);
+ }
+ 
+ MACHINE_START(RD88F5182, "Marvell Orion-NAS Reference Design")
+--- a/arch/arm/mach-orion5x/ts209-setup.c
++++ b/arch/arm/mach-orion5x/ts209-setup.c
+@@ -332,16 +332,9 @@
+ 
+  * General Setup
+  ****************************************************************************/
+-
+-static struct platform_device *qnap_ts209_devices[] __initdata = {
+-	&qnap_ts209_nor_flash,
+-	&qnap_ts209_button_device,
+-};
+-
+ /*
+  * QNAP TS-[12]09 specific power off method via UART1-attached PIC
+  */
+-
+ #define UART1_REG(x)	(UART1_VIRT_BASE + ((UART_##x) << 2))
+ 
+ static void qnap_ts209_power_off(void)
+@@ -372,12 +365,6 @@
+ 	orion5x_init();
+ 
+ 	/*
+-	 * Setup flash mapping
+-	 */
+-	orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE,
+-				   QNAP_TS209_NOR_BOOT_SIZE);
+-
+-	/*
+ 	 * Open a special address decode windows for the PCIe WA.
+ 	 */
+ 	orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
+@@ -411,11 +398,22 @@
+ 	orion5x_write(MPP_16_19_CTRL, 0x5500);
+ 	orion5x_gpio_set_valid_pins(0x3cc0fff);
+ 
+-	/* register ts209 specific power-off method */
+-	pm_power_off = qnap_ts209_power_off;
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	orion5x_ehci1_init();
++	ts209_find_mac_addr();
++	orion5x_eth_init(&qnap_ts209_eth_data);
++	orion5x_i2c_init();
++	orion5x_sata_init(&qnap_ts209_sata_data);
++	orion5x_uart0_init();
++
++	orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE,
++				   QNAP_TS209_NOR_BOOT_SIZE);
++	platform_device_register(&qnap_ts209_nor_flash);
+ 
+-	platform_add_devices(qnap_ts209_devices,
+-				ARRAY_SIZE(qnap_ts209_devices));
++	platform_device_register(&qnap_ts209_button_device);
+ 
+ 	/* Get RTC IRQ and register the chip */
+ 	if (gpio_request(TS209_RTC_GPIO, "rtc") == 0) {
+@@ -428,10 +426,8 @@
+ 		pr_warning("qnap_ts209_init: failed to get RTC IRQ\n");
+ 	i2c_register_board_info(0, &qnap_ts209_i2c_rtc, 1);
+ 
+-	ts209_find_mac_addr();
+-	orion5x_eth_init(&qnap_ts209_eth_data);
+-
+-	orion5x_sata_init(&qnap_ts209_sata_data);
++	/* register ts209 specific power-off method */
++	pm_power_off = qnap_ts209_power_off;
+ }
+ 
+ MACHINE_START(TS209, "QNAP TS-109/TS-209")
diff --git a/target/linux/orion/patches/011-move_setting_up_pcie_wa_window_into_pcie.patch b/target/linux/orion/patches/011-move_setting_up_pcie_wa_window_into_pcie.patch
new file mode 100644
index 0000000..f6e78d8
--- /dev/null
+++ b/target/linux/orion/patches/011-move_setting_up_pcie_wa_window_into_pcie.patch
@@ -0,0 +1,90 @@
+It makes no sense to do PCIe WA window setup in the individual
+board support files while the decision whether or not to use the
+PCIe WA access method is made in a different place, in the PCIe
+support code.
+
+This patch moves the configuration of a PCIe WA window from the
+individual Orion board support files to the central Orion PCIe
+support code.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/dns323-setup.c      |    7 -------
+ arch/arm/mach-orion5x/kurobox_pro-setup.c |    6 ------
+ arch/arm/mach-orion5x/pci.c               |    2 ++
+ arch/arm/mach-orion5x/rd88f5182-setup.c   |    6 ------
+ arch/arm/mach-orion5x/ts209-setup.c       |    6 ------
+ 5 files changed, 2 insertions(+), 25 deletions(-)
+
+--- a/arch/arm/mach-orion5x/dns323-setup.c
++++ b/arch/arm/mach-orion5x/dns323-setup.c
+@@ -247,13 +247,6 @@
+ 	/* Setup basic Orion functions. Need to be called early. */
+ 	orion5x_init();
+ 
+-	/* DNS-323 has a Marvell 88X7042 SATA controller attached via PCIe
+-	 *
+-	 * Open a special address decode windows for the PCIe WA.
+-	 */
+-	orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
+-				ORION5X_PCIE_WA_SIZE);
+-
+ 	/* set MPP to 0 as D-Link's 2.6.12.6 kernel did */
+ 	orion5x_write(MPP_0_7_CTRL, 0);
+ 	orion5x_write(MPP_8_15_CTRL, 0);
+--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
++++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
+@@ -188,12 +188,6 @@
+ 	orion5x_init();
+ 
+ 	/*
+-	 * Open a special address decode windows for the PCIe WA.
+-	 */
+-	orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
+-				ORION5X_PCIE_WA_SIZE);
+-
+-	/*
+ 	 * Setup Multiplexing Pins --
+ 	 * MPP[0-1] Not used
+ 	 * MPP[2] GPIO Micon
+--- a/arch/arm/mach-orion5x/pci.c
++++ b/arch/arm/mach-orion5x/pci.c
+@@ -152,6 +152,8 @@
+ 	if (dev == MV88F5181_DEV_ID || dev == MV88F5182_DEV_ID) {
+ 		printk(KERN_NOTICE "Applying Orion-1/Orion-NAS PCIe config "
+ 				   "read transaction workaround\n");
++		orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
++					  ORION5X_PCIE_WA_SIZE);
+ 		pcie_ops.read = pcie_rd_conf_wa;
+ 	}
+ 
+--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
++++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
+@@ -249,12 +249,6 @@
+ 	orion5x_init();
+ 
+ 	/*
+-	 * Open a special address decode windows for the PCIe WA.
+-	 */
+-	orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
+-				ORION5X_PCIE_WA_SIZE);
+-
+-	/*
+ 	 * Setup Multiplexing Pins --
+ 	 * MPP[0] Debug Led (GPIO - Out)
+ 	 * MPP[1] Debug Led (GPIO - Out)
+--- a/arch/arm/mach-orion5x/ts209-setup.c
++++ b/arch/arm/mach-orion5x/ts209-setup.c
+@@ -365,12 +365,6 @@
+ 	orion5x_init();
+ 
+ 	/*
+-	 * Open a special address decode windows for the PCIe WA.
+-	 */
+-	orion5x_setup_pcie_wa_win(ORION5X_PCIE_WA_PHYS_BASE,
+-				ORION5X_PCIE_WA_SIZE);
+-
+-	/*
+ 	 * Setup Multiplexing Pins --
+ 	 * MPP[0] Reserved
+ 	 * MPP[1] USB copy button (0 active)
diff --git a/target/linux/orion/patches/012-rework_mpp_handling.patch b/target/linux/orion/patches/012-rework_mpp_handling.patch
new file mode 100644
index 0000000..05e1881
--- /dev/null
+++ b/target/linux/orion/patches/012-rework_mpp_handling.patch
@@ -0,0 +1,583 @@
+Instead of having board code poke directly into the MPP configuration
+registers, and separately calling orion5x_gpio_set_valid_pins() to
+indicate which MPP pins can be used as GPIO pins, introduce a helper
+function for configuring the roles of each of the MPP pins, and have
+that helper function handle gpio validity internally.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+Acked-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
+---
+ arch/arm/mach-orion5x/Makefile            |    2 +-
+ arch/arm/mach-orion5x/common.h            |    2 +-
+ arch/arm/mach-orion5x/db88f5281-setup.c   |   42 +++++----
+ arch/arm/mach-orion5x/dns323-setup.c      |   50 +++++------
+ arch/arm/mach-orion5x/gpio.c              |    7 +-
+ arch/arm/mach-orion5x/kurobox_pro-setup.c |   41 ++++----
+ arch/arm/mach-orion5x/mpp.c               |  142 +++++++++++++++++++++++++++++
+ arch/arm/mach-orion5x/mpp.h               |   63 +++++++++++++
+ arch/arm/mach-orion5x/rd88f5182-setup.c   |   43 +++++----
+ arch/arm/mach-orion5x/ts209-setup.c       |   43 +++++----
+ 10 files changed, 321 insertions(+), 114 deletions(-)
+ create mode 100644 arch/arm/mach-orion5x/mpp.c
+ create mode 100644 arch/arm/mach-orion5x/mpp.h
+
+--- a/arch/arm/mach-orion5x/Makefile
++++ b/arch/arm/mach-orion5x/Makefile
+@@ -1,4 +1,4 @@
+-obj-y				+= common.o addr-map.o pci.o gpio.o irq.o
++obj-y				+= common.o addr-map.o pci.o gpio.o irq.o mpp.o
+ obj-$(CONFIG_MACH_DB88F5281)	+= db88f5281-setup.o
+ obj-$(CONFIG_MACH_RD88F5182)	+= rd88f5182-setup.o
+ obj-$(CONFIG_MACH_KUROBOX_PRO)	+= kurobox_pro-setup.o
+--- a/arch/arm/mach-orion5x/common.h
++++ b/arch/arm/mach-orion5x/common.h
+@@ -48,7 +48,7 @@
+  * Valid GPIO pins according to MPP setup, used by machine-setup.
+  * (/mach-orion/gpio.c).
+  */
+-void orion5x_gpio_set_valid_pins(u32 pins);
++void orion5x_gpio_set_valid(unsigned pin, int valid);
+ void gpio_display(void);	/* debug */
+ 
+ struct machine_desc;
+--- a/arch/arm/mach-orion5x/db88f5281-setup.c
++++ b/arch/arm/mach-orion5x/db88f5281-setup.c
+@@ -27,6 +27,7 @@
+ #include <asm/arch/orion5x.h>
+ #include <asm/plat-orion/orion_nand.h>
+ #include "common.h"
++#include "mpp.h"
+ 
+ /*****************************************************************************
+  * DB-88F5281 on board devices
+@@ -305,26 +306,27 @@
+ 	 */
+ 	orion5x_init();
+ 
+-	/*
+-	 * Setup Multiplexing Pins:
+-	 * MPP0: GPIO (USB Over Current)	MPP1: GPIO (USB Vbat input)
+-	 * MPP2: PCI_REQn[2]			MPP3: PCI_GNTn[2]
+-	 * MPP4: PCI_REQn[3]			MPP5: PCI_GNTn[3]
+-	 * MPP6: GPIO (JP0, CON17.2)		MPP7: GPIO (JP1, CON17.1)
+-	 * MPP8: GPIO (JP2, CON11.2)		MPP9: GPIO (JP3, CON11.3)
+-	 * MPP10: GPIO (RTC int)		MPP11: GPIO (Baud Rate Generator)
+-	 * MPP12: GPIO (PCI int 1)		MPP13: GPIO (PCI int 2)
+-	 * MPP14: NAND_REn[2]			MPP15: NAND_WEn[2]
+-	 * MPP16: UART1_RX			MPP17: UART1_TX
+-	 * MPP18: UART1_CTS			MPP19: UART1_RTS
+-	 * MPP-DEV: DEV_D[16:31]
+-	 */
+-	orion5x_write(MPP_0_7_CTRL, 0x00222203);
+-	orion5x_write(MPP_8_15_CTRL, 0x44000000);
+-	orion5x_write(MPP_16_19_CTRL, 0);
+-	orion5x_write(MPP_DEV_CTRL, 0);
+-
+-	orion5x_gpio_set_valid_pins(0x00003fc3);
++	orion5x_mpp_conf(0, MPP_GPIO);		/* USB Over Current */
++	orion5x_mpp_conf(1, MPP_GPIO);		/* USB Vbat input */
++	orion5x_mpp_conf(2, MPP_PCI_ARB);	/* PCI_REQn[2] */
++	orion5x_mpp_conf(3, MPP_PCI_ARB);	/* PCI_GNTn[2] */
++	orion5x_mpp_conf(4, MPP_PCI_ARB);	/* PCI_REQn[3] */
++	orion5x_mpp_conf(5, MPP_PCI_ARB);	/* PCI_GNTn[3] */
++	orion5x_mpp_conf(6, MPP_GPIO);		/* JP0, CON17.2 */
++	orion5x_mpp_conf(7, MPP_GPIO);		/* JP1, CON17.1 */
++	orion5x_mpp_conf(8, MPP_GPIO);		/* JP2, CON11.2 */
++	orion5x_mpp_conf(9, MPP_GPIO);		/* JP3, CON11.3 */
++	orion5x_mpp_conf(10, MPP_GPIO);		/* RTC int */
++	orion5x_mpp_conf(11, MPP_GPIO);		/* Baud Rate Generator */
++	orion5x_mpp_conf(12, MPP_GPIO);		/* PCI int 1 */
++	orion5x_mpp_conf(13, MPP_GPIO);		/* PCI int 2 */
++	orion5x_mpp_conf(14, MPP_NAND);		/* NAND_REn[2] */
++	orion5x_mpp_conf(15, MPP_NAND);		/* NAND_WEn[2] */
++	orion5x_mpp_conf(16, MPP_UART);		/* UART1_RX */
++	orion5x_mpp_conf(17, MPP_UART);		/* UART1_TX */
++	orion5x_mpp_conf(18, MPP_UART);		/* UART1_CTSn */
++	orion5x_mpp_conf(19, MPP_UART);		/* UART1_RTSn */
++	orion5x_write(MPP_DEV_CTRL, 0);		/* DEV_D[31:16] */
+ 
+ 	/*
+ 	 * Configure peripherals.
+--- a/arch/arm/mach-orion5x/dns323-setup.c
++++ b/arch/arm/mach-orion5x/dns323-setup.c
+@@ -27,6 +27,7 @@
+ #include <asm/mach/pci.h>
+ #include <asm/arch/orion5x.h>
+ #include "common.h"
++#include "mpp.h"
+ 
+ #define DNS323_GPIO_LED_RIGHT_AMBER	1
+ #define DNS323_GPIO_LED_LEFT_AMBER	2
+@@ -247,34 +248,27 @@
+ 	/* Setup basic Orion functions. Need to be called early. */
+ 	orion5x_init();
+ 
+-	/* set MPP to 0 as D-Link's 2.6.12.6 kernel did */
+-	orion5x_write(MPP_0_7_CTRL, 0);
+-	orion5x_write(MPP_8_15_CTRL, 0);
+-	orion5x_write(MPP_16_19_CTRL, 0);
+-	orion5x_write(MPP_DEV_CTRL, 0);
+-
+-	/* Define used GPIO pins
+-
+-	  GPIO Map:
+-
+-	  |  0 |     | PEX_RST_OUT (not controlled by GPIO)
+-	  |  1 | Out | right amber LED (= sata ch0 LED)  (low-active)
+-	  |  2 | Out | left  amber LED (= sata ch1 LED)  (low-active)
+-	  |  3 | Out | //unknown//
+-	  |  4 | Out | power button LED (low-active, together with pin #5)
+-	  |  5 | Out | power button LED (low-active, together with pin #4)
+-	  |  6 | In  | GMT G751-2f overtemp. shutdown signal (low-active)
+-	  |  7 | In  | M41T80 nIRQ/OUT/SQW signal
+-	  |  8 | Out | triggers power off (high-active)
+-	  |  9 | In  | power button switch (low-active)
+-	  | 10 | In  | reset button switch (low-active)
+-	  | 11 | Out | //unknown//
+-	  | 12 | Out | //unknown//
+-	  | 13 | Out | //unknown//
+-	  | 14 | Out | //unknown//
+-	  | 15 | Out | //unknown//
+-	*/
+-	orion5x_gpio_set_valid_pins(0x07f6);
++	orion5x_mpp_conf(0, MPP_PCIE_RST_OUTn);
++	orion5x_mpp_conf(1, MPP_GPIO);		/* right amber LED (sata ch0) */
++	orion5x_mpp_conf(2, MPP_GPIO);		/* left amber LED (sata ch1) */
++	orion5x_mpp_conf(3, MPP_UNUSED);
++	orion5x_mpp_conf(4, MPP_GPIO);		/* power button LED */
++	orion5x_mpp_conf(5, MPP_GPIO);		/* power button LED */
++	orion5x_mpp_conf(6, MPP_GPIO);		/* GMT G751-2f overtemp */
++	orion5x_mpp_conf(7, MPP_GPIO);		/* M41T80 nIRQ/OUT/SQW */
++	orion5x_mpp_conf(8, MPP_GPIO);		/* triggers power off */
++	orion5x_mpp_conf(9, MPP_GPIO);		/* power button switch */
++	orion5x_mpp_conf(10, MPP_GPIO);		/* reset button switch */
++	orion5x_mpp_conf(11, MPP_UNUSED);
++	orion5x_mpp_conf(12, MPP_UNUSED);
++	orion5x_mpp_conf(13, MPP_UNUSED);
++	orion5x_mpp_conf(14, MPP_UNUSED);
++	orion5x_mpp_conf(15, MPP_UNUSED);
++	orion5x_mpp_conf(16, MPP_UNUSED);
++	orion5x_mpp_conf(17, MPP_UNUSED);
++	orion5x_mpp_conf(18, MPP_UNUSED);
++	orion5x_mpp_conf(19, MPP_UNUSED);
++	orion5x_write(MPP_DEV_CTRL, 0);		/* DEV_D[31:16] */
+ 
+ 	/*
+ 	 * Configure peripherals.
+--- a/arch/arm/mach-orion5x/gpio.c
++++ b/arch/arm/mach-orion5x/gpio.c
+@@ -24,9 +24,12 @@
+ static unsigned long gpio_valid[BITS_TO_LONGS(GPIO_MAX)];
+ static const char *gpio_label[GPIO_MAX];  /* non null for allocated GPIOs */
+ 
+-void __init orion5x_gpio_set_valid_pins(u32 pins)
++void __init orion5x_gpio_set_valid(unsigned pin, int valid)
+ {
+-	gpio_valid[0] = pins;
++	if (valid)
++		__set_bit(pin, gpio_valid);
++	else
++		__clear_bit(pin, gpio_valid);
+ }
+ 
+ /*
+--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
++++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
+@@ -25,6 +25,7 @@
+ #include <asm/arch/orion5x.h>
+ #include <asm/plat-orion/orion_nand.h>
+ #include "common.h"
++#include "mpp.h"
+ 
+ /*****************************************************************************
+  * KUROBOX-PRO Info
+@@ -187,26 +188,26 @@
+ 	 */
+ 	orion5x_init();
+ 
+-	/*
+-	 * Setup Multiplexing Pins --
+-	 * MPP[0-1] Not used
+-	 * MPP[2] GPIO Micon
+-	 * MPP[3] GPIO RTC
+-	 * MPP[4-5] Not used
+-	 * MPP[6] Nand Flash REn
+-	 * MPP[7] Nand Flash WEn
+-	 * MPP[8-11] Not used
+-	 * MPP[12] SATA 0 presence Indication
+-	 * MPP[13] SATA 1 presence Indication
+-	 * MPP[14] SATA 0 active Indication
+-	 * MPP[15] SATA 1 active indication
+-	 * MPP[16-19] Not used
+-	 */
+-	orion5x_write(MPP_0_7_CTRL, 0x44220003);
+-	orion5x_write(MPP_8_15_CTRL, 0x55550000);
+-	orion5x_write(MPP_16_19_CTRL, 0x0);
+-
+-	orion5x_gpio_set_valid_pins(0x0000000c);
++	orion5x_mpp_conf(0, MPP_UNUSED);
++	orion5x_mpp_conf(1, MPP_UNUSED);
++	orion5x_mpp_conf(2, MPP_GPIO);		/* GPIO Micon */
++	orion5x_mpp_conf(3, MPP_GPIO);		/* GPIO Rtc */
++	orion5x_mpp_conf(4, MPP_UNUSED);
++	orion5x_mpp_conf(5, MPP_UNUSED);
++	orion5x_mpp_conf(6, MPP_NAND);		/* NAND Flash REn */
++	orion5x_mpp_conf(7, MPP_NAND);		/* NAND Flash WEn */
++	orion5x_mpp_conf(8, MPP_UNUSED);
++	orion5x_mpp_conf(9, MPP_UNUSED);
++	orion5x_mpp_conf(10, MPP_UNUSED);
++	orion5x_mpp_conf(11, MPP_UNUSED);
++	orion5x_mpp_conf(12, MPP_SATA_LED);	/* SATA 0 presence */
++	orion5x_mpp_conf(13, MPP_SATA_LED);	/* SATA 1 presence */
++	orion5x_mpp_conf(14, MPP_SATA_LED);	/* SATA 0 active */
++	orion5x_mpp_conf(15, MPP_SATA_LED);	/* SATA 1 active */
++	orion5x_mpp_conf(16, MPP_UNUSED);
++	orion5x_mpp_conf(17, MPP_UNUSED);
++	orion5x_mpp_conf(18, MPP_UNUSED);
++	orion5x_mpp_conf(19, MPP_UNUSED);
+ 
+ 	/*
+ 	 * Configure peripherals.
+--- /dev/null
++++ b/arch/arm/mach-orion5x/mpp.c
+@@ -0,0 +1,142 @@
++/*
++ * arch/arm/mach-orion5x/mpp.c
++ *
++ * MPP functions for Marvell Orion 5x SoCs
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2.  This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/mbus.h>
++#include <asm/hardware.h>
++#include <asm/io.h>
++#include "common.h"
++#include "mpp.h"
++
++static int is_5182(void)
++{
++	u32 dev;
++	u32 rev;
++
++	orion5x_pcie_id(&dev, &rev);
++
++	return !!(dev == MV88F5182_DEV_ID);
++}
++
++static int is_5281(void)
++{
++	u32 dev;
++	u32 rev;
++
++	orion5x_pcie_id(&dev, &rev);
++
++	return !!(dev == MV88F5281_DEV_ID);
++}
++
++static int __init determine_type_encoding(int mpp, enum orion5x_mpp_type type)
++{
++	switch (type) {
++	case MPP_UNUSED:
++	case MPP_GPIO:
++		if (mpp == 0)
++			return 3;
++		if (mpp >= 1 && mpp <= 15)
++			return 0;
++		if (mpp >= 16 && mpp <= 19) {
++			if (is_5182())
++				return 5;
++			if (type == MPP_UNUSED)
++				return 0;
++		}
++		return -1;
++
++	case MPP_PCIE_RST_OUTn:
++		if (mpp == 0)
++			return 0;
++		return -1;
++
++	case MPP_PCI_ARB:
++		if (mpp >= 0 && mpp <= 7)
++			return 2;
++		return -1;
++
++	case MPP_PCI_PMEn:
++		if (mpp == 2)
++			return 3;
++		return -1;
++
++	case MPP_GIGE:
++		if (mpp >= 8 && mpp <= 15)
++			return 1;
++		return -1;
++
++	case MPP_NAND:
++		if (is_5182() || is_5281()) {
++			if (mpp >= 4 && mpp <= 7)
++				return 4;
++			if (mpp >= 12 && mpp <= 17)
++				return 4;
++		}
++		return -1;
++
++
++	case MPP_SATA_LED:
++		if (is_5182()) {
++			if (mpp >= 4 && mpp <= 7)
++				return 5;
++			if (mpp >= 12 && mpp <= 15)
++				return 5;
++		}
++		return -1;
++
++	case MPP_UART:
++		if (mpp >= 16 && mpp <= 19)
++			return 0;
++		return -1;
++	}
++
++	printk(KERN_INFO "unknown MPP type %d\n", type);
++
++	return -1;
++}
++
++static void __init set_mpp_type(int mpp, int num_type)
++{
++	unsigned long reg;
++	u32 value;
++
++	if (mpp >= 0 && mpp <= 7)
++		reg = MPP_0_7_CTRL;
++	else if (mpp >= 8 && mpp <= 15)
++		reg = MPP_8_15_CTRL;
++	else if (mpp >= 16 && mpp <= 19)
++		reg = MPP_16_19_CTRL;
++	else
++		return;
++
++	mpp &= 7;
++
++	value = readl(reg);
++	value &= ~(0xf << (mpp << 2));
++	value |= (num_type & 0xf) << (mpp << 2);
++	writel(value, reg);
++}
++
++void __init orion5x_mpp_conf(int mpp, enum orion5x_mpp_type type)
++{
++	int num_type;
++
++	num_type = determine_type_encoding(mpp, type);
++	if (num_type < 0) {
++		printk(KERN_ERR "orion5x_mpp_conf: invalid MPP "
++				"combination (%d, %d)\n", mpp, type);
++		return;
++	}
++
++	set_mpp_type(mpp, num_type);
++
++	orion5x_gpio_set_valid(mpp, (type == MPP_GPIO) ? 1 : 0);
++}
+--- /dev/null
++++ b/arch/arm/mach-orion5x/mpp.h
+@@ -0,0 +1,63 @@
++#ifndef __ARCH_ORION5X_MPP_H
++#define __ARCH_ORION5X_MPP_H
++
++enum orion5x_mpp_type {
++	/*
++	 * This MPP is unused.
++	 */
++	MPP_UNUSED,
++
++	/*
++	 * This MPP pin is used as a generic GPIO pin.  Valid for
++	 * MPPs 0-15 and device bus data pins 16-31.  On 5182, also
++	 * valid for MPPs 16-19.
++	 */
++	MPP_GPIO,
++
++	/*
++	 * This MPP is used as PCIe_RST_OUTn pin.  Valid for
++	 * MPP 0 only.
++	 */
++	MPP_PCIE_RST_OUTn,
++
++	/*
++	 * This MPP is used as PCI arbiter pin (REQn/GNTn.)
++	 * Valid for MPPs 0-7 only.
++	 */
++	MPP_PCI_ARB,
++
++	/*
++	 * This MPP is used as PCI_PMEn pin.  Valid for MPP 2 only.
++	 */
++	MPP_PCI_PMEn,
++
++	/*
++	 * This MPP is used as GigE half-duplex (COL, CRS) or GMII
++	 * (RXERR, CRS, TXERR, TXD[7:4], RXD[7:4]) pin.  Valid for
++	 * MPPs 8-19 only.
++	 */
++	MPP_GIGE,
++
++	/*
++	 * This MPP is used as NAND REn/WEn pin.  Valid for MPPs
++	 * 4-7 and 12-17 only, and only on the 5181l/5182/5281.
++	 */
++	MPP_NAND,
++
++	/*
++	 * This MPP is used as a SATA presence/activity LED.
++	 * Valid for MPPs 4-7 and 12-15 only, and only on the 5182.
++	 */
++	MPP_SATA_LED,
++
++	/*
++	 * This MPP is used as UART1 RXD/TXD/CTSn/RTSn pin.
++	 * Valid for MPPs 16-19 only.
++	 */
++	MPP_UART,
++};
++
++void orion5x_mpp_conf(int mpp, enum orion5x_mpp_type type);
++
++
++#endif
+--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
++++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
+@@ -26,6 +26,7 @@
+ #include <asm/mach/pci.h>
+ #include <asm/arch/orion5x.h>
+ #include "common.h"
++#include "mpp.h"
+ 
+ /*****************************************************************************
+  * RD-88F5182 Info
+@@ -248,22 +249,28 @@
+ 	 */
+ 	orion5x_init();
+ 
++	orion5x_mpp_conf(0, MPP_GPIO);		/* Debug Led */
++	orion5x_mpp_conf(1, MPP_GPIO);		/* Reset Switch */
++	orion5x_mpp_conf(2, MPP_UNUSED);
++	orion5x_mpp_conf(3, MPP_GPIO);		/* RTC Int */
++	orion5x_mpp_conf(4, MPP_GPIO);
++	orion5x_mpp_conf(5, MPP_GPIO);
++	orion5x_mpp_conf(6, MPP_GPIO);		/* PCI_intA */
++	orion5x_mpp_conf(7, MPP_GPIO);		/* PCI_intB */
++	orion5x_mpp_conf(8, MPP_UNUSED);
++	orion5x_mpp_conf(9, MPP_UNUSED);
++	orion5x_mpp_conf(10, MPP_UNUSED);
++	orion5x_mpp_conf(11, MPP_UNUSED);
++	orion5x_mpp_conf(12, MPP_SATA_LED);	/* SATA 0 presence */
++	orion5x_mpp_conf(13, MPP_SATA_LED);	/* SATA 1 presence */
++	orion5x_mpp_conf(14, MPP_SATA_LED);	/* SATA 0 active */
++	orion5x_mpp_conf(15, MPP_SATA_LED);	/* SATA 1 active */
++	orion5x_mpp_conf(16, MPP_UNUSED);
++	orion5x_mpp_conf(17, MPP_UNUSED);
++	orion5x_mpp_conf(18, MPP_UNUSED);
++	orion5x_mpp_conf(19, MPP_UNUSED);
++
+ 	/*
+-	 * Setup Multiplexing Pins --
+-	 * MPP[0] Debug Led (GPIO - Out)
+-	 * MPP[1] Debug Led (GPIO - Out)
+-	 * MPP[2] N/A
+-	 * MPP[3] RTC_Int (GPIO - In)
+-	 * MPP[4] GPIO
+-	 * MPP[5] GPIO
+-	 * MPP[6] PCI_intA (GPIO - In)
+-	 * MPP[7] PCI_intB (GPIO - In)
+-	 * MPP[8-11] N/A
+-	 * MPP[12] SATA 0 presence Indication
+-	 * MPP[13] SATA 1 presence Indication
+-	 * MPP[14] SATA 0 active Indication
+-	 * MPP[15] SATA 1 active indication
+-	 * MPP[16-19] Not used
+ 	 * MPP[20] PCI Clock to MV88F5182
+ 	 * MPP[21] PCI Clock to mini PCI CON11
+ 	 * MPP[22] USB 0 over current indication
+@@ -272,12 +279,6 @@
+ 	 * MPP[25] USB 0 over current enable
+ 	 */
+ 
+-	orion5x_write(MPP_0_7_CTRL, 0x00000003);
+-	orion5x_write(MPP_8_15_CTRL, 0x55550000);
+-	orion5x_write(MPP_16_19_CTRL, 0x5555);
+-
+-	orion5x_gpio_set_valid_pins(0x000000fb);
+-
+ 	/*
+ 	 * Configure peripherals.
+ 	 */
+--- a/arch/arm/mach-orion5x/ts209-setup.c
++++ b/arch/arm/mach-orion5x/ts209-setup.c
+@@ -28,6 +28,7 @@
+ #include <asm/mach/pci.h>
+ #include <asm/arch/orion5x.h>
+ #include "common.h"
++#include "mpp.h"
+ 
+ #define QNAP_TS209_NOR_BOOT_BASE 0xf4000000
+ #define QNAP_TS209_NOR_BOOT_SIZE SZ_8M
+@@ -364,33 +365,33 @@
+ 	 */
+ 	orion5x_init();
+ 
++	orion5x_mpp_conf(0, MPP_UNUSED);
++	orion5x_mpp_conf(1, MPP_GPIO);		/* USB copy button */
++	orion5x_mpp_conf(2, MPP_GPIO);		/* Load defaults button */
++	orion5x_mpp_conf(3, MPP_GPIO);		/* GPIO RTC */
++	orion5x_mpp_conf(4, MPP_UNUSED);
++	orion5x_mpp_conf(5, MPP_UNUSED);
++	orion5x_mpp_conf(6, MPP_GPIO);		/* PCI Int A */
++	orion5x_mpp_conf(7, MPP_GPIO);		/* PCI Int B */
++	orion5x_mpp_conf(8, MPP_UNUSED);
++	orion5x_mpp_conf(9, MPP_UNUSED);
++	orion5x_mpp_conf(10, MPP_UNUSED);
++	orion5x_mpp_conf(11, MPP_UNUSED);
++	orion5x_mpp_conf(12, MPP_SATA_LED);	/* SATA 0 presence */
++	orion5x_mpp_conf(13, MPP_SATA_LED);	/* SATA 1 presence */
++	orion5x_mpp_conf(14, MPP_SATA_LED);	/* SATA 0 active */
++	orion5x_mpp_conf(15, MPP_SATA_LED);	/* SATA 1 active */
++	orion5x_mpp_conf(16, MPP_UART);		/* UART1 RXD */
++	orion5x_mpp_conf(17, MPP_UART);		/* UART1 TXD */
++	orion5x_mpp_conf(18, MPP_GPIO);		/* SW_RST */
++	orion5x_mpp_conf(19, MPP_UNUSED);
++
+ 	/*
+-	 * Setup Multiplexing Pins --
+-	 * MPP[0] Reserved
+-	 * MPP[1] USB copy button (0 active)
+-	 * MPP[2] Load defaults button (0 active)
+-	 * MPP[3] GPIO RTC
+-	 * MPP[4-5] Reserved
+-	 * MPP[6] PCI Int A
+-	 * MPP[7] PCI Int B
+-	 * MPP[8-11] Reserved
+-	 * MPP[12] SATA 0 presence
+-	 * MPP[13] SATA 1 presence
+-	 * MPP[14] SATA 0 active
+-	 * MPP[15] SATA 1 active
+-	 * MPP[16] UART1 RXD
+-	 * MPP[17] UART1 TXD
+-	 * MPP[18] SW_RST (0 active)
+-	 * MPP[19] Reserved
+ 	 * MPP[20] PCI clock 0
+ 	 * MPP[21] PCI clock 1
+ 	 * MPP[22] USB 0 over current
+ 	 * MPP[23-25] Reserved
+ 	 */
+-	orion5x_write(MPP_0_7_CTRL, 0x3);
+-	orion5x_write(MPP_8_15_CTRL, 0x55550000);
+-	orion5x_write(MPP_16_19_CTRL, 0x5500);
+-	orion5x_gpio_set_valid_pins(0x3cc0fff);
+ 
+ 	/*
+ 	 * Configure peripherals.
diff --git a/target/linux/orion/patches/013-add_88f5181l_support.patch b/target/linux/orion/patches/013-add_88f5181l_support.patch
new file mode 100644
index 0000000..b902777
--- /dev/null
+++ b/target/linux/orion/patches/013-add_88f5181l_support.patch
@@ -0,0 +1,56 @@
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/Kconfig                       |    3 ++-
+ arch/arm/mach-orion5x/common.c         |    4 +++-
+ include/asm-arm/arch-orion5x/orion5x.h |    5 +++--
+ 3 files changed, 8 insertions(+), 4 deletions(-)
+
+--- a/arch/arm/Kconfig
++++ b/arch/arm/Kconfig
+@@ -385,7 +385,8 @@
+ 	select PLAT_ORION
+ 	help
+ 	  Support for the following Marvell Orion 5x series SoCs:
+-	  Orion-1 (5181), Orion-NAS (5182), Orion-2 (5281.)
++	  Orion-1 (5181), Orion-VoIP (5181L), Orion-NAS (5182),
++	  Orion-2 (5281.)
+ 
+ config ARCH_PNX4008
+ 	bool "Philips Nexperia PNX4008 Mobile"
+--- a/arch/arm/mach-orion5x/common.c
++++ b/arch/arm/mach-orion5x/common.c
+@@ -394,8 +394,10 @@
+ 	} else if (*dev == MV88F5181_DEV_ID) {
+ 		if (*rev == MV88F5181_REV_B1) {
+ 			*dev_name = "MV88F5181-Rev-B1";
++		} else if (*rev == MV88F5181L_REV_A1) {
++			*dev_name = "MV88F5181L-Rev-A1";
+ 		} else {
+-			*dev_name = "MV88F5181-Rev-Unsupported";
++			*dev_name = "MV88F5181(L)-Rev-Unsupported";
+ 		}
+ 	} else {
+ 		*dev_name = "Device-Unknown";
+--- a/include/asm-arm/arch-orion5x/orion5x.h
++++ b/include/asm-arm/arch-orion5x/orion5x.h
+@@ -2,7 +2,7 @@
+  * include/asm-arm/arch-orion5x/orion5x.h
+  *
+  * Generic definitions of Orion SoC flavors:
+- *  Orion-1, Orion-NAS, Orion-VoIP, and Orion-2.
++ *  Orion-1, Orion-VoIP, Orion-NAS, and Orion-2.
+  *
+  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
+  *
+@@ -63,9 +63,10 @@
+ /*******************************************************************************
+  * Supported Devices & Revisions
+  ******************************************************************************/
+-/* Orion-1 (88F5181) */
++/* Orion-1 (88F5181) and Orion-VoIP (88F5181L) */
+ #define MV88F5181_DEV_ID	0x5181
+ #define MV88F5181_REV_B1	3
++#define MV88F5181L_REV_A1	9
+ /* Orion-NAS (88F5182) */
+ #define MV88F5182_DEV_ID	0x5182
+ #define MV88F5182_REV_A2	2
diff --git a/target/linux/orion/patches/014-avoid_setting_force_phy_addr.patch b/target/linux/orion/patches/014-avoid_setting_force_phy_addr.patch
new file mode 100644
index 0000000..d47e5dd
--- /dev/null
+++ b/target/linux/orion/patches/014-avoid_setting_force_phy_addr.patch
@@ -0,0 +1,71 @@
+The mv643xx_eth platform data field ->force_phy_addr only needs
+to be set if the passed-in ->phy_addr field is zero (to distinguish
+the case of not having specified a phy address
+(force_phy_addr = 0) from the case where a phy address of zero needs
+to be used (force_phy_addr = 1.))
+
+Also, the ->force_phy_addr field will hopefully disappear in a
+future mv643xx_eth reorganisation.
+
+Therefore, this patch deletes the ->force_phy_addr field initialiser
+from all Orion board code.
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/db88f5281-setup.c   |    1 -
+ arch/arm/mach-orion5x/dns323-setup.c      |    1 -
+ arch/arm/mach-orion5x/kurobox_pro-setup.c |    1 -
+ arch/arm/mach-orion5x/rd88f5182-setup.c   |    1 -
+ arch/arm/mach-orion5x/ts209-setup.c       |    1 -
+ 5 files changed, 0 insertions(+), 5 deletions(-)
+
+--- a/arch/arm/mach-orion5x/db88f5281-setup.c
++++ b/arch/arm/mach-orion5x/db88f5281-setup.c
+@@ -286,7 +286,6 @@
+  ****************************************************************************/
+ static struct mv643xx_eth_platform_data db88f5281_eth_data = {
+ 	.phy_addr	= 8,
+-	.force_phy_addr = 1,
+ };
+ 
+ /*****************************************************************************
+--- a/arch/arm/mach-orion5x/dns323-setup.c
++++ b/arch/arm/mach-orion5x/dns323-setup.c
+@@ -82,7 +82,6 @@
+ 
+ static struct mv643xx_eth_platform_data dns323_eth_data = {
+ 	.phy_addr = 8,
+-	.force_phy_addr = 1,
+ };
+ 
+ /****************************************************************************
+--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
++++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
+@@ -160,7 +160,6 @@
+ 
+ static struct mv643xx_eth_platform_data kurobox_pro_eth_data = {
+ 	.phy_addr	= 8,
+-	.force_phy_addr = 1,
+ };
+ 
+ /*****************************************************************************
+--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
++++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
+@@ -222,7 +222,6 @@
+ 
+ static struct mv643xx_eth_platform_data rd88f5182_eth_data = {
+ 	.phy_addr	= 8,
+-	.force_phy_addr = 1,
+ };
+ 
+ /*****************************************************************************
+--- a/arch/arm/mach-orion5x/ts209-setup.c
++++ b/arch/arm/mach-orion5x/ts209-setup.c
+@@ -191,7 +191,6 @@
+ 
+ static struct mv643xx_eth_platform_data qnap_ts209_eth_data = {
+ 	.phy_addr	= 8,
+-	.force_phy_addr	= 1,
+ };
+ 
+ static int __init parse_hex_nibble(char n)
diff --git a/target/linux/orion/patches/015-implement_power-off_method_for_kurobox_pro.patch b/target/linux/orion/patches/015-implement_power-off_method_for_kurobox_pro.patch
new file mode 100644
index 0000000..5814852
--- /dev/null
+++ b/target/linux/orion/patches/015-implement_power-off_method_for_kurobox_pro.patch
@@ -0,0 +1,192 @@
+From: Sylver Bruneau <sylver.bruneau@googlemail.com>
+
+This patch implements the communication with the microcontroller on the
+Kurobox Pro and Linkstation Pro/Live boards.  This is allowing to send
+the commands needed to power-off the board correctly.
+
+Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
+---
+ arch/arm/mach-orion5x/kurobox_pro-setup.c |  147 ++++++++++++++++++++++++++++-
+ 1 files changed, 143 insertions(+), 4 deletions(-)
+
+--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
++++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
+@@ -13,10 +13,12 @@
+ #include <linux/platform_device.h>
+ #include <linux/pci.h>
+ #include <linux/irq.h>
++#include <linux/delay.h>
+ #include <linux/mtd/physmap.h>
+ #include <linux/mtd/nand.h>
+ #include <linux/mv643xx_eth.h>
+ #include <linux/i2c.h>
++#include <linux/serial_reg.h>
+ #include <linux/ata_platform.h>
+ #include <asm/mach-types.h>
+ #include <asm/gpio.h>
+@@ -177,6 +179,140 @@
+ };
+ 
+ /*****************************************************************************
++ * Kurobox Pro specific power off method via UART1-attached microcontroller
++ ****************************************************************************/
++
++#define UART1_REG(x)	(UART1_VIRT_BASE + ((UART_##x) << 2))
++
++static int kurobox_pro_miconread(unsigned char *buf, int count)
++{
++	int i;
++	int timeout;
++
++	for (i = 0; i < count; i++) {
++		timeout = 10;
++
++		while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) {
++			if (--timeout == 0)
++				break;
++			udelay(1000);
++		}
++
++		if (timeout == 0)
++			break;
++		buf[i] = readl(UART1_REG(RX));
++	}
++
++	/* return read bytes */
++	return i;
++}
++
++static int kurobox_pro_miconwrite(const unsigned char *buf, int count)
++{
++	int i = 0;
++
++	while (count--) {
++		while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE))
++			barrier();
++		writel(buf[i++], UART1_REG(TX));
++	}
++
++	return 0;
++}
++
++static int kurobox_pro_miconsend(const unsigned char *data, int count)
++{
++	int i;
++	unsigned char checksum = 0;
++	unsigned char recv_buf[40];
++	unsigned char send_buf[40];
++	unsigned char correct_ack[3];
++	int retry = 2;
++
++	/* Generate checksum */
++	for (i = 0; i < count; i++)
++		checksum -=  data[i];
++
++	do {
++		/* Send data */
++		kurobox_pro_miconwrite(data, count);
++
++		/* send checksum */
++		kurobox_pro_miconwrite(&checksum, 1);
++
++		if (kurobox_pro_miconread(recv_buf, sizeof(recv_buf)) <= 3) {
++			printk(KERN_ERR ">%s: receive failed.\n", __func__);
++
++			/* send preamble to clear the receive buffer */
++			memset(&send_buf, 0xff, sizeof(send_buf));
++			kurobox_pro_miconwrite(send_buf, sizeof(send_buf));
++
++			/* make dummy reads */
++			mdelay(100);
++			kurobox_pro_miconread(recv_buf, sizeof(recv_buf));
++		} else {
++			/* Generate expected ack */
++			correct_ack[0] = 0x01;
++			correct_ack[1] = data[1];
++			correct_ack[2] = 0x00;
++
++			/* checksum Check */
++			if ((recv_buf[0] + recv_buf[1] + recv_buf[2] +
++			     recv_buf[3]) & 0xFF) {
++				printk(KERN_ERR ">%s: Checksum Error : "
++					"Received data[%02x, %02x, %02x, %02x]"
++					"\n", __func__, recv_buf[0],
++					recv_buf[1], recv_buf[2], recv_buf[3]);
++			} else {
++				/* Check Received Data */
++				if (correct_ack[0] == recv_buf[0] &&
++				    correct_ack[1] == recv_buf[1] &&
++				    correct_ack[2] == recv_buf[2]) {
++					/* Interval for next command */
++					mdelay(10);
++
++					/* Receive ACK */
++					return 0;
++				}
++			}
++			/* Received NAK or illegal Data */
++			printk(KERN_ERR ">%s: Error : NAK or Illegal Data "
++					"Received\n", __func__);
++		}
++	} while (retry--);
++
++	/* Interval for next command */
++	mdelay(10);
++
++	return -1;
++}
++
++static void kurobox_pro_power_off(void)
++{
++	const unsigned char watchdogkill[]	= {0x01, 0x35, 0x00};
++	const unsigned char shutdownwait[]	= {0x00, 0x0c};
++	const unsigned char poweroff[]		= {0x00, 0x06};
++	/* 38400 baud divisor */
++	const unsigned divisor = ((ORION5X_TCLK + (8 * 38400)) / (16 * 38400));
++
++	pr_info("%s: triggering power-off...\n", __func__);
++
++	/* hijack uart1 and reset into sane state (38400,8n1,even parity) */
++	writel(0x83, UART1_REG(LCR));
++	writel(divisor & 0xff, UART1_REG(DLL));
++	writel((divisor >> 8) & 0xff, UART1_REG(DLM));
++	writel(0x1b, UART1_REG(LCR));
++	writel(0x00, UART1_REG(IER));
++	writel(0x07, UART1_REG(FCR));
++	writel(0x00, UART1_REG(MCR));
++
++	/* Send the commands to shutdown the Kurobox Pro */
++	kurobox_pro_miconsend(watchdogkill, sizeof(watchdogkill)) ;
++	kurobox_pro_miconsend(shutdownwait, sizeof(shutdownwait)) ;
++	kurobox_pro_miconsend(poweroff, sizeof(poweroff));
++}
++
++/*****************************************************************************
+  * General Setup
+  ****************************************************************************/
+ 
+@@ -203,10 +339,10 @@
+ 	orion5x_mpp_conf(13, MPP_SATA_LED);	/* SATA 1 presence */
+ 	orion5x_mpp_conf(14, MPP_SATA_LED);	/* SATA 0 active */
+ 	orion5x_mpp_conf(15, MPP_SATA_LED);	/* SATA 1 active */
+-	orion5x_mpp_conf(16, MPP_UNUSED);
+-	orion5x_mpp_conf(17, MPP_UNUSED);
+-	orion5x_mpp_conf(18, MPP_UNUSED);
+-	orion5x_mpp_conf(19, MPP_UNUSED);
++	orion5x_mpp_conf(16, MPP_UART);		/* UART1 RXD */
++	orion5x_mpp_conf(17, MPP_UART);		/* UART1 TXD */
++	orion5x_mpp_conf(18, MPP_UART);		/* UART1 CTSn */
++	orion5x_mpp_conf(19, MPP_UART);		/* UART1 RTSn */
+ 
+ 	/*
+ 	 * Configure peripherals.
+@@ -229,6 +365,9 @@
+ 	}
+ 
+ 	i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);
++
++	/* register Kurobox Pro specific power-off method */
++	pm_power_off = kurobox_pro_power_off;
+ }
+ 
+ #ifdef CONFIG_MACH_KUROBOX_PRO
diff --git a/target/linux/orion/patches/016-add_qnap_ts-409_support.patch b/target/linux/orion/patches/016-add_qnap_ts-409_support.patch
new file mode 100644
index 0000000..a0d22f7
--- /dev/null
+++ b/target/linux/orion/patches/016-add_qnap_ts-409_support.patch
@@ -0,0 +1,418 @@
+From: Sylver Bruneau <sylver.bruneau@googlemail.com>
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/Kconfig       |    6 +
+ arch/arm/mach-orion5x/Makefile      |    1 +
+ arch/arm/mach-orion5x/ts409-setup.c |  383 +++++++++++++++++++++++++++++++++++
+ 3 files changed, 390 insertions(+), 0 deletions(-)
+ create mode 100644 arch/arm/mach-orion5x/ts409-setup.c
+
+--- a/arch/arm/mach-orion5x/Kconfig
++++ b/arch/arm/mach-orion5x/Kconfig
+@@ -44,6 +44,12 @@
+ 	  Buffalo Linkstation Pro/Live platform. Both v1 and
+ 	  v2 devices are supported.
+ 
++config MACH_TS409
++	bool "QNAP TS-409"
++	help
++	  Say 'Y' here if you want your kernel to support the
++	  QNAP TS-409 platform.
++
+ endmenu
+ 
+ endif
+--- a/arch/arm/mach-orion5x/Makefile
++++ b/arch/arm/mach-orion5x/Makefile
+@@ -5,3 +5,4 @@
+ obj-$(CONFIG_MACH_LINKSTATION_PRO) += kurobox_pro-setup.o
+ obj-$(CONFIG_MACH_DNS323)	+= dns323-setup.o
+ obj-$(CONFIG_MACH_TS209)	+= ts209-setup.o
++obj-$(CONFIG_MACH_TS409)	+= ts409-setup.o
+--- /dev/null
++++ b/arch/arm/mach-orion5x/ts409-setup.c
+@@ -0,0 +1,383 @@
++/*
++ * QNAP TS-409 Board Setup
++ *
++ * Maintainer: Sylver Bruneau <sylver.bruneau@gmail.com>
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version
++ * 2 of the License, or (at your option) any later version.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/pci.h>
++#include <linux/irq.h>
++#include <linux/mtd/physmap.h>
++#include <linux/mv643xx_eth.h>
++#include <linux/gpio_keys.h>
++#include <linux/input.h>
++#include <linux/i2c.h>
++#include <linux/serial_reg.h>
++#include <asm/mach-types.h>
++#include <asm/gpio.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/pci.h>
++#include <asm/arch/orion5x.h>
++#include "common.h"
++#include "mpp.h"
++
++/*****************************************************************************
++ * QNAP TS-409 Info
++ ****************************************************************************/
++
++/*
++ * QNAP TS-409 hardware :
++ * - Marvell 88F5281-D0
++ * - Marvell 88SX7042 SATA controller (PCIe)
++ * - Marvell 88E1118 Gigabit Ethernet PHY
++ * - RTC S35390A (@0x30) on I2C bus
++ * - 8MB NOR flash
++ * - 256MB of DDR-2 RAM
++ */
++
++/*
++ * 8MB NOR flash Device bus boot chip select
++ */
++
++#define QNAP_TS409_NOR_BOOT_BASE 0xff800000
++#define QNAP_TS409_NOR_BOOT_SIZE SZ_8M
++
++/****************************************************************************
++ * 8MiB NOR flash. The struct mtd_partition is not in the same order as the
++ *     partitions on the device because we want to keep compatability with
++ *     existing QNAP firmware.
++ *
++ * Layout as used by QNAP:
++ *  [2] 0x00000000-0x00200000 : "Kernel"
++ *  [3] 0x00200000-0x00600000 : "RootFS1"
++ *  [4] 0x00600000-0x00700000 : "RootFS2"
++ *  [6] 0x00700000-0x00760000 : "NAS Config" (read-only)
++ *  [5] 0x00760000-0x00780000 : "U-Boot Config"
++ *  [1] 0x00780000-0x00800000 : "U-Boot" (read-only)
++ ***************************************************************************/
++static struct mtd_partition qnap_ts409_partitions[] = {
++	{
++		.name		= "U-Boot",
++		.size		= 0x00080000,
++		.offset		= 0x00780000,
++		.mask_flags	= MTD_WRITEABLE,
++	}, {
++		.name		= "Kernel",
++		.size		= 0x00200000,
++		.offset		= 0,
++	}, {
++		.name		= "RootFS1",
++		.size		= 0x00400000,
++		.offset		= 0x00200000,
++	}, {
++		.name		= "RootFS2",
++		.size		= 0x00100000,
++		.offset		= 0x00600000,
++	}, {
++		.name		= "U-Boot Config",
++		.size		= 0x00020000,
++		.offset		= 0x00760000,
++	}, {
++		.name		= "NAS Config",
++		.size		= 0x00060000,
++		.offset		= 0x00700000,
++		.mask_flags	= MTD_WRITEABLE,
++	},
++};
++
++static struct physmap_flash_data qnap_ts409_nor_flash_data = {
++	.width		= 1,
++	.parts		= qnap_ts409_partitions,
++	.nr_parts	= ARRAY_SIZE(qnap_ts409_partitions)
++};
++
++static struct resource qnap_ts409_nor_flash_resource = {
++	.flags	= IORESOURCE_MEM,
++	.start	= QNAP_TS409_NOR_BOOT_BASE,
++	.end	= QNAP_TS409_NOR_BOOT_BASE + QNAP_TS409_NOR_BOOT_SIZE - 1,
++};
++
++static struct platform_device qnap_ts409_nor_flash = {
++	.name		= "physmap-flash",
++	.id		= 0,
++	.dev		= { .platform_data = &qnap_ts409_nor_flash_data, },
++	.num_resources	= 1,
++	.resource	= &qnap_ts409_nor_flash_resource,
++};
++
++/*****************************************************************************
++ * PCI
++ ****************************************************************************/
++
++static int __init qnap_ts409_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	int irq;
++
++	/*
++	 * Check for devices with hard-wired IRQs.
++	 */
++	irq = orion5x_pci_map_irq(dev, slot, pin);
++	if (irq != -1)
++		return irq;
++
++	/*
++	 * PCI isn't used on the TS-409
++	 */
++	printk(KERN_ERR "kurobox_pro_pci_map_irq failed, unknown bus\n");
++	return -1;
++}
++
++static struct hw_pci qnap_ts409_pci __initdata = {
++	.nr_controllers	= 2,
++	.swizzle	= pci_std_swizzle,
++	.setup		= orion5x_pci_sys_setup,
++	.scan		= orion5x_pci_sys_scan_bus,
++	.map_irq	= qnap_ts409_pci_map_irq,
++};
++
++static int __init qnap_ts409_pci_init(void)
++{
++	if (machine_is_ts409())
++		pci_common_init(&qnap_ts409_pci);
++
++	return 0;
++}
++
++subsys_initcall(qnap_ts409_pci_init);
++
++/*****************************************************************************
++ * Ethernet
++ ****************************************************************************/
++
++static struct mv643xx_eth_platform_data qnap_ts409_eth_data = {
++	.phy_addr	= 8,
++};
++
++static int __init parse_hex_nibble(char n)
++{
++	if (n >= '0' && n <= '9')
++		return n - '0';
++
++	if (n >= 'A' && n <= 'F')
++		return n - 'A' + 10;
++
++	if (n >= 'a' && n <= 'f')
++		return n - 'a' + 10;
++
++	return -1;
++}
++
++static int __init parse_hex_byte(const char *b)
++{
++	int hi;
++	int lo;
++
++	hi = parse_hex_nibble(b[0]);
++	lo = parse_hex_nibble(b[1]);
++
++	if (hi < 0 || lo < 0)
++		return -1;
++
++	return (hi << 4) | lo;
++}
++
++static int __init check_mac_addr(const char *addr_str)
++{
++	u_int8_t addr[6];
++	int i;
++
++	for (i = 0; i < 6; i++) {
++		int byte;
++
++		/*
++		 * Enforce "xx:xx:xx:xx:xx:xx\n" format.
++		 */
++		if (addr_str[(i * 3) + 2] != ((i < 5) ? ':' : '\n'))
++			return -1;
++
++		byte = parse_hex_byte(addr_str + (i * 3));
++		if (byte < 0)
++			return -1;
++		addr[i] = byte;
++	}
++
++	printk(KERN_INFO "ts409: found ethernet mac address ");
++	for (i = 0; i < 6; i++)
++		printk("%.2x%s", addr[i], (i < 5) ? ":" : ".\n");
++
++	memcpy(qnap_ts409_eth_data.mac_addr, addr, 6);
++
++	return 0;
++}
++
++/*
++ * The 'NAS Config' flash partition has an ext2 filesystem which
++ * contains a file that has the ethernet MAC address in plain text
++ * (format "xx:xx:xx:xx:xx:xx\n".)
++ */
++static void __init ts409_find_mac_addr(void)
++{
++	unsigned long addr;
++
++	for (addr = 0x00700000; addr < 0x00760000; addr += 1024) {
++		char *nor_page;
++		int ret = 0;
++
++		nor_page = ioremap(QNAP_TS409_NOR_BOOT_BASE + addr, 1024);
++		if (nor_page != NULL) {
++			ret = check_mac_addr(nor_page);
++			iounmap(nor_page);
++		}
++
++		if (ret == 0)
++			break;
++	}
++}
++
++/*****************************************************************************
++ * RTC S35390A on I2C bus
++ ****************************************************************************/
++
++#define TS409_RTC_GPIO	10
++
++static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = {
++	I2C_BOARD_INFO("s35390a", 0x30),
++	.irq		= 0,
++};
++
++/****************************************************************************
++ * GPIO Attached Keys
++ *     Power button is attached to the PIC microcontroller
++ ****************************************************************************/
++
++#define QNAP_TS409_GPIO_KEY_MEDIA	15
++
++static struct gpio_keys_button qnap_ts409_buttons[] = {
++	{
++		.code		= KEY_RESTART,
++		.gpio		= QNAP_TS409_GPIO_KEY_MEDIA,
++		.desc		= "USB Copy Button",
++		.active_low	= 1,
++	},
++};
++
++static struct gpio_keys_platform_data qnap_ts409_button_data = {
++	.buttons	= qnap_ts409_buttons,
++	.nbuttons	= ARRAY_SIZE(qnap_ts409_buttons),
++};
++
++static struct platform_device qnap_ts409_button_device = {
++	.name		= "gpio-keys",
++	.id		= -1,
++	.num_resources	= 0,
++	.dev		= {
++		.platform_data	= &qnap_ts409_button_data,
++	},
++};
++
++/*****************************************************************************
++ * General Setup
++ ****************************************************************************/
++
++/*
++ * QNAP TS-409 specific power off method via UART1-attached PIC
++ */
++
++#define UART1_REG(x)  (UART1_VIRT_BASE + ((UART_##x) << 2))
++
++static void qnap_ts409_power_off(void)
++{
++	/* 19200 baud divisor */
++	const unsigned divisor = ((ORION5X_TCLK + (8 * 19200)) / (16 * 19200));
++
++	pr_info("%s: triggering power-off...\n", __func__);
++
++	/* hijack uart1 and reset into sane state (19200,8n1) */
++	writel(0x83, UART1_REG(LCR));
++	writel(divisor & 0xff, UART1_REG(DLL));
++	writel((divisor >> 8) & 0xff, UART1_REG(DLM));
++	writel(0x03, UART1_REG(LCR));
++	writel(0x00, UART1_REG(IER));
++	writel(0x00, UART1_REG(FCR));
++	writel(0x00, UART1_REG(MCR));
++
++	/* send the power-off command 'A' to PIC */
++	writel('A', UART1_REG(TX));
++}
++
++static void __init qnap_ts409_init(void)
++{
++	/*
++	 * Setup basic Orion functions. Need to be called early.
++	 */
++	orion5x_init();
++
++	orion5x_mpp_conf(0, MPP_UNUSED);
++	orion5x_mpp_conf(1, MPP_UNUSED);
++	orion5x_mpp_conf(2, MPP_UNUSED);
++	orion5x_mpp_conf(3, MPP_UNUSED);
++	orion5x_mpp_conf(4, MPP_GPIO);		/* HDD 1 status */
++	orion5x_mpp_conf(5, MPP_GPIO);		/* HDD 2 status */
++	orion5x_mpp_conf(6, MPP_GPIO);		/* HDD 3 status */
++	orion5x_mpp_conf(7, MPP_GPIO);		/* HDD 4 status */
++	orion5x_mpp_conf(8, MPP_UNUSED);
++	orion5x_mpp_conf(9, MPP_UNUSED);
++	orion5x_mpp_conf(10, MPP_GPIO);		/* RTC int */
++	orion5x_mpp_conf(11, MPP_UNUSED);
++	orion5x_mpp_conf(12, MPP_UNUSED);
++	orion5x_mpp_conf(13, MPP_UNUSED);
++	orion5x_mpp_conf(14, MPP_GPIO);		/* SW_RST */
++	orion5x_mpp_conf(15, MPP_GPIO);		/* USB copy button */
++	orion5x_mpp_conf(16, MPP_UART);		/* UART1 RXD */
++	orion5x_mpp_conf(17, MPP_UART);		/* UART1 TXD */
++	orion5x_mpp_conf(18, MPP_UNUSED);
++	orion5x_mpp_conf(19, MPP_UNUSED);
++
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	ts409_find_mac_addr();
++	orion5x_eth_init(&qnap_ts409_eth_data);
++	orion5x_i2c_init();
++	orion5x_uart0_init();
++
++	orion5x_setup_dev_boot_win(QNAP_TS409_NOR_BOOT_BASE,
++				   QNAP_TS409_NOR_BOOT_SIZE);
++	platform_device_register(&qnap_ts409_nor_flash);
++
++	platform_device_register(&qnap_ts409_button_device);
++
++	/* Get RTC IRQ and register the chip */
++	if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) {
++		if (gpio_direction_input(TS409_RTC_GPIO) == 0)
++			qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO);
++		else
++			gpio_free(TS409_RTC_GPIO);
++	}
++	if (qnap_ts409_i2c_rtc.irq == 0)
++		pr_warning("qnap_ts409_init: failed to get RTC IRQ\n");
++	i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1);
++
++	/* register ts409 specific power-off method */
++	pm_power_off = qnap_ts409_power_off;
++}
++
++MACHINE_START(TS409, "QNAP TS-409")
++	/* Maintainer:  Sylver Bruneau <sylver.bruneau@gmail.com> */
++	.phys_io	= ORION5X_REGS_PHYS_BASE,
++	.io_pg_offst	= ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
++	.boot_params	= 0x00000100,
++	.init_machine	= qnap_ts409_init,
++	.map_io		= orion5x_map_io,
++	.init_irq	= orion5x_init_irq,
++	.timer		= &orion5x_timer,
++	.fixup		= tag_fixup_mem32,
++MACHINE_END
diff --git a/target/linux/orion/patches/017-add_linksys_wrt350n_v2_support.patch b/target/linux/orion/patches/017-add_linksys_wrt350n_v2_support.patch
new file mode 100644
index 0000000..5faa959
--- /dev/null
+++ b/target/linux/orion/patches/017-add_linksys_wrt350n_v2_support.patch
@@ -0,0 +1,205 @@
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+Tested-by: Dirk Teurlings <dirk@upexia.nl>
+Tested-by: Peter van Valderen <p.v.valderen@gmail.com>
+---
+ arch/arm/mach-orion5x/Kconfig            |    6 +
+ arch/arm/mach-orion5x/Makefile           |    1 +
+ arch/arm/mach-orion5x/wrt350n-v2-setup.c |  170 ++++++++++++++++++++++++++++++
+ 3 files changed, 177 insertions(+), 0 deletions(-)
+ create mode 100644 arch/arm/mach-orion5x/wrt350n-v2-setup.c
+
+--- a/arch/arm/mach-orion5x/Kconfig
++++ b/arch/arm/mach-orion5x/Kconfig
+@@ -50,6 +50,12 @@
+ 	  Say 'Y' here if you want your kernel to support the
+ 	  QNAP TS-409 platform.
+ 
++config MACH_WRT350N_V2
++	bool "Linksys WRT350N v2"
++	help
++	  Say 'Y' here if you want your kernel to support the
++	  Linksys WRT350N v2 platform.
++
+ endmenu
+ 
+ endif
+--- a/arch/arm/mach-orion5x/Makefile
++++ b/arch/arm/mach-orion5x/Makefile
+@@ -6,3 +6,4 @@
+ obj-$(CONFIG_MACH_DNS323)	+= dns323-setup.o
+ obj-$(CONFIG_MACH_TS209)	+= ts209-setup.o
+ obj-$(CONFIG_MACH_TS409)	+= ts409-setup.o
++obj-$(CONFIG_MACH_WRT350N_V2)	+= wrt350n-v2-setup.o
+--- /dev/null
++++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+@@ -0,0 +1,170 @@
++/*
++ * arch/arm/mach-orion5x/wrt350n-v2-setup.c
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2.  This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/pci.h>
++#include <linux/irq.h>
++#include <linux/delay.h>
++#include <linux/mtd/physmap.h>
++#include <linux/mv643xx_eth.h>
++#include <asm/mach-types.h>
++#include <asm/gpio.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/pci.h>
++#include <asm/arch/orion5x.h>
++#include "common.h"
++#include "mpp.h"
++
++/*
++ * 8M NOR flash Device bus boot chip select
++ */
++#define WRT350N_V2_NOR_BOOT_BASE	0xf4000000
++#define WRT350N_V2_NOR_BOOT_SIZE	SZ_8M
++
++static struct mtd_partition wrt350n_v2_nor_flash_partitions[] = {
++	{
++		.name		= "kernel",
++		.offset		= 0x00000000,
++		.size		= 0x00760000,
++	}, {
++		.name		= "rootfs",
++		.offset		= 0x001a0000,
++		.size		= 0x005c0000,
++	}, {
++		.name		= "lang",
++		.offset		= 0x00760000,
++		.size		= 0x00040000,
++	}, {
++		.name		= "nvram",
++		.offset		= 0x007a0000,
++		.size		= 0x00020000,
++	}, {
++		.name		= "u-boot",
++		.offset		= 0x007c0000,
++		.size		= 0x00040000,
++	},
++};
++
++static struct physmap_flash_data wrt350n_v2_nor_flash_data = {
++	.width		= 1,
++	.parts		= wrt350n_v2_nor_flash_partitions,
++	.nr_parts	= ARRAY_SIZE(wrt350n_v2_nor_flash_partitions),
++};
++
++static struct resource wrt350n_v2_nor_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++	.start		= WRT350N_V2_NOR_BOOT_BASE,
++	.end		= WRT350N_V2_NOR_BOOT_BASE + WRT350N_V2_NOR_BOOT_SIZE - 1,
++};
++
++static struct platform_device wrt350n_v2_nor_flash = {
++	.name			= "physmap-flash",
++	.id			= 0,
++	.dev		= {
++		.platform_data	= &wrt350n_v2_nor_flash_data,
++	},
++	.num_resources		= 1,
++	.resource		= &wrt350n_v2_nor_flash_resource,
++};
++
++static struct mv643xx_eth_platform_data wrt350n_v2_eth_data = {
++	.phy_addr	= -1,
++};
++
++static void __init wrt350n_v2_init(void)
++{
++	/*
++	 * Setup basic Orion functions. Need to be called early.
++	 */
++	orion5x_init();
++
++	orion5x_mpp_conf(0, MPP_GPIO);		/* Power LED green (0=on) */
++	orion5x_mpp_conf(1, MPP_GPIO);		/* Security LED (0=on) */
++	orion5x_mpp_conf(2, MPP_GPIO);		/* Internal Button (0=on) */
++	orion5x_mpp_conf(3, MPP_GPIO);		/* Reset Button (0=on) */
++	orion5x_mpp_conf(4, MPP_GPIO);		/* PCI int */
++	orion5x_mpp_conf(5, MPP_GPIO);		/* Power LED orange (0=on) */
++	orion5x_mpp_conf(6, MPP_GPIO);		/* USB LED (0=on) */
++	orion5x_mpp_conf(7, MPP_GPIO);		/* Wireless LED (0=on) */
++	orion5x_mpp_conf(8, MPP_UNUSED);	/* ??? */
++	orion5x_mpp_conf(9, MPP_GIGE);		/* GE_RXERR */
++	orion5x_mpp_conf(10, MPP_UNUSED);	/* ??? */
++	orion5x_mpp_conf(11, MPP_UNUSED);	/* ??? */
++	orion5x_mpp_conf(12, MPP_GIGE);		/* GE_TXD[4] */
++	orion5x_mpp_conf(13, MPP_GIGE);		/* GE_TXD[5] */
++	orion5x_mpp_conf(14, MPP_GIGE);		/* GE_TXD[6] */
++	orion5x_mpp_conf(15, MPP_GIGE);		/* GE_TXD[7] */
++	orion5x_mpp_conf(16, MPP_GIGE);		/* GE_RXD[4] */
++	orion5x_mpp_conf(17, MPP_GIGE);		/* GE_RXD[5] */
++	orion5x_mpp_conf(18, MPP_GIGE);		/* GE_RXD[6] */
++	orion5x_mpp_conf(19, MPP_GIGE);		/* GE_RXD[7] */
++
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	orion5x_eth_init(&wrt350n_v2_eth_data);
++	orion5x_uart0_init();
++
++	orion5x_setup_dev_boot_win(WRT350N_V2_NOR_BOOT_BASE,
++				   WRT350N_V2_NOR_BOOT_SIZE);
++	platform_device_register(&wrt350n_v2_nor_flash);
++}
++
++static int __init wrt350n_v2_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	int irq;
++
++	/*
++	 * Check for devices with hard-wired IRQs.
++	 */
++	irq = orion5x_pci_map_irq(dev, slot, pin);
++	if (irq != -1)
++		return irq;
++
++	/*
++	 * Mini-PCI slot.
++	 */
++	if (slot == 7)
++		return gpio_to_irq(4);
++
++	printk(KERN_ERR "wrt350n_v2_pci_map_irq failed, unknown bus\n");
++
++	return -1;
++}
++
++static struct hw_pci wrt350n_v2_pci __initdata = {
++	.nr_controllers	= 2,
++	.swizzle	= pci_std_swizzle,
++	.setup		= orion5x_pci_sys_setup,
++	.scan		= orion5x_pci_sys_scan_bus,
++	.map_irq	= wrt350n_v2_pci_map_irq,
++};
++
++static int __init wrt350n_v2_pci_init(void)
++{
++	if (machine_is_wrt350n_v2())
++		pci_common_init(&wrt350n_v2_pci);
++
++	return 0;
++}
++subsys_initcall(wrt350n_v2_pci_init);
++
++MACHINE_START(WRT350N_V2, "Linksys WRT350N v2")
++	/* Maintainer: Lennert Buytenhek <buytenh@marvell.com> */
++	.phys_io	= ORION5X_REGS_PHYS_BASE,
++	.io_pg_offst	= ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
++	.boot_params	= 0x00000100,
++	.init_machine	= wrt350n_v2_init,
++	.map_io		= orion5x_map_io,
++	.init_irq	= orion5x_init_irq,
++	.timer		= &orion5x_timer,
++	.fixup		= tag_fixup_mem32,
++MACHINE_END
diff --git a/target/linux/orion/patches/018-add_hp_media_vault_mv2120_support.patch b/target/linux/orion/patches/018-add_hp_media_vault_mv2120_support.patch
new file mode 100644
index 0000000..02a93c9
--- /dev/null
+++ b/target/linux/orion/patches/018-add_hp_media_vault_mv2120_support.patch
@@ -0,0 +1,263 @@
+From: Martin Michlmayr <tbm@cyrius.com>
+
+Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
+---
+ arch/arm/mach-orion5x/Kconfig        |    6 +
+ arch/arm/mach-orion5x/Makefile       |    1 +
+ arch/arm/mach-orion5x/mv2120-setup.c |  228 ++++++++++++++++++++++++++++++++++
+ 3 files changed, 235 insertions(+), 0 deletions(-)
+ create mode 100644 arch/arm/mach-orion5x/mv2120-setup.c
+
+--- a/arch/arm/mach-orion5x/Kconfig
++++ b/arch/arm/mach-orion5x/Kconfig
+@@ -56,6 +56,12 @@
+ 	  Say 'Y' here if you want your kernel to support the
+ 	  Linksys WRT350N v2 platform.
+ 
++config MACH_MV2120
++	bool "HP Media Vault mv2120"
++	help
++	  Say 'Y' here if you want your kernel to support the
++	  HP Media Vault mv2120 or mv5100.
++
+ endmenu
+ 
+ endif
+--- a/arch/arm/mach-orion5x/Makefile
++++ b/arch/arm/mach-orion5x/Makefile
+@@ -7,3 +7,4 @@
+ obj-$(CONFIG_MACH_TS209)	+= ts209-setup.o
+ obj-$(CONFIG_MACH_TS409)	+= ts409-setup.o
+ obj-$(CONFIG_MACH_WRT350N_V2)	+= wrt350n-v2-setup.o
++obj-$(CONFIG_MACH_MV2120)	+= mv2120-setup.o
+--- /dev/null
++++ b/arch/arm/mach-orion5x/mv2120-setup.c
+@@ -0,0 +1,228 @@
++/*
++ * Copyright (C) 2007 Herbert Valerio Riedel <hvr@gnu.org>
++ * Copyright (C) 2008 Martin Michlmayr <tbm@cyrius.com>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU Lesser General Public License as
++ * published by the Free Software Foundation; either version 2 of the
++ * License, or (at your option) any later version.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/pci.h>
++#include <linux/irq.h>
++#include <linux/mtd/physmap.h>
++#include <linux/mv643xx_eth.h>
++#include <linux/leds.h>
++#include <linux/gpio_keys.h>
++#include <linux/input.h>
++#include <linux/i2c.h>
++#include <linux/ata_platform.h>
++#include <asm/mach-types.h>
++#include <asm/gpio.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/pci.h>
++#include <asm/arch/orion5x.h>
++#include "common.h"
++#include "mpp.h"
++
++#define MV2120_NOR_BOOT_BASE	0xf4000000
++#define MV2120_NOR_BOOT_SIZE	SZ_512K
++
++#define MV2120_GPIO_RTC_IRQ	3
++#define MV2120_GPIO_KEY_RESET	17
++#define MV2120_GPIO_KEY_POWER	18
++#define MV2120_GPIO_POWER_OFF	19
++
++
++/****************************************************************************
++ * PCI setup
++ ****************************************************************************/
++static int __init mv2120_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++	int irq;
++
++	/*
++	 * Check for devices with hard-wired IRQs.
++	 */
++	irq = orion5x_pci_map_irq(dev, slot, pin);
++	if (irq != -1)
++		return irq;
++
++	pr_err("%s: requested mapping for unknown bus\n", __func__);
++
++	return -1;
++}
++
++static struct hw_pci mv2120_pci __initdata = {
++	.nr_controllers = 2,
++	.swizzle	= pci_std_swizzle,
++	.setup		= orion5x_pci_sys_setup,
++	.scan		= orion5x_pci_sys_scan_bus,
++	.map_irq	= mv2120_pci_map_irq,
++};
++
++static int __init mv2120_pci_init(void)
++{
++	if (machine_is_mv2120())
++		pci_common_init(&mv2120_pci);
++
++	return 0;
++}
++subsys_initcall(mv2120_pci_init);
++
++
++/*****************************************************************************
++ * Ethernet
++ ****************************************************************************/
++static struct mv643xx_eth_platform_data mv2120_eth_data = {
++	.phy_addr	= 8,
++};
++
++static struct mv_sata_platform_data mv2120_sata_data = {
++	.n_ports	= 2,
++};
++
++static struct mtd_partition mv2120_partitions[] = {
++	{
++		.name	= "firmware",
++		.size	= 0x00080000,
++		.offset	= 0,
++	},
++};
++
++static struct physmap_flash_data mv2120_nor_flash_data = {
++	.width		= 1,
++	.parts		= mv2120_partitions,
++	.nr_parts	= ARRAY_SIZE(mv2120_partitions)
++};
++
++static struct resource mv2120_nor_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++	.start		= MV2120_NOR_BOOT_BASE,
++	.end		= MV2120_NOR_BOOT_BASE + MV2120_NOR_BOOT_SIZE - 1,
++};
++
++static struct platform_device mv2120_nor_flash = {
++	.name		= "physmap-flash",
++	.id		= 0,
++	.dev		= {
++		.platform_data	= &mv2120_nor_flash_data,
++	},
++	.resource	= &mv2120_nor_flash_resource,
++	.num_resources	= 1,
++};
++
++static struct gpio_keys_button mv2120_buttons[] = {
++	{
++		.code		= KEY_RESTART,
++		.gpio		= MV2120_GPIO_KEY_RESET,
++		.desc		= "Reset Button",
++		.active_low	= 1,
++	}, {
++		.code		= KEY_POWER,
++		.gpio		= MV2120_GPIO_KEY_POWER,
++		.desc		= "Power Button",
++		.active_low	= 1,
++	},
++};
++
++static struct gpio_keys_platform_data mv2120_button_data = {
++	.buttons	= mv2120_buttons,
++	.nbuttons	= ARRAY_SIZE(mv2120_buttons),
++};
++
++static struct platform_device mv2120_button_device = {
++	.name		= "gpio-keys",
++	.id		= -1,
++	.num_resources	= 0,
++	.dev		= {
++		.platform_data	= &mv2120_button_data,
++	},
++};
++
++
++/****************************************************************************
++ * General Setup
++ ****************************************************************************/
++static struct i2c_board_info __initdata mv2120_i2c_rtc = {
++	I2C_BOARD_INFO("rtc-pcf8563", 0x51),
++	.irq	= 0,
++};
++
++static void mv2120_power_off(void)
++{
++	pr_info("%s: triggering power-off...\n", __func__);
++	gpio_set_value(MV2120_GPIO_POWER_OFF, 0);
++}
++
++static void __init mv2120_init(void)
++{
++	/* Setup basic Orion functions. Need to be called early. */
++	orion5x_init();
++
++	orion5x_mpp_conf(0, MPP_GPIO);		/* Sys status LED */
++	orion5x_mpp_conf(1, MPP_GPIO);		/* Sys error LED */
++	orion5x_mpp_conf(2, MPP_GPIO);		/* OverTemp interrupt */
++	orion5x_mpp_conf(3, MPP_GPIO);		/* RTC interrupt */
++	orion5x_mpp_conf(4, MPP_GPIO);		/* V_LED 5V */
++	orion5x_mpp_conf(5, MPP_GPIO);		/* V_LED 3.3V */
++	orion5x_mpp_conf(6, MPP_UNUSED);
++	orion5x_mpp_conf(7, MPP_UNUSED);
++	orion5x_mpp_conf(8, MPP_GPIO);		/* SATA 0 fail LED */
++	orion5x_mpp_conf(9, MPP_GPIO);		/* SATA 1 fail LED */
++	orion5x_mpp_conf(10, MPP_UNUSED);
++	orion5x_mpp_conf(11, MPP_UNUSED);
++	orion5x_mpp_conf(12, MPP_SATA_LED);	/* SATA 0 presence */
++	orion5x_mpp_conf(13, MPP_SATA_LED);	/* SATA 1 presence */
++	orion5x_mpp_conf(14, MPP_SATA_LED);	/* SATA 0 active */
++	orion5x_mpp_conf(15, MPP_SATA_LED);	/* SATA 1 active */
++	orion5x_mpp_conf(16, MPP_UNUSED);
++	orion5x_mpp_conf(17, MPP_GPIO);		/* Reset button */
++	orion5x_mpp_conf(18, MPP_GPIO);		/* Power button */
++	orion5x_mpp_conf(19, MPP_GPIO);		/* Power off */
++
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	orion5x_ehci1_init();
++	orion5x_eth_init(&mv2120_eth_data);
++	orion5x_i2c_init();
++	orion5x_sata_init(&mv2120_sata_data);
++	orion5x_uart0_init();
++
++	orion5x_setup_dev_boot_win(MV2120_NOR_BOOT_BASE, MV2120_NOR_BOOT_SIZE);
++	platform_device_register(&mv2120_nor_flash);
++
++	platform_device_register(&mv2120_button_device);
++
++	if (gpio_request(MV2120_GPIO_RTC_IRQ, "rtc") == 0) {
++		if (gpio_direction_input(MV2120_GPIO_RTC_IRQ) == 0)
++			mv2120_i2c_rtc.irq = gpio_to_irq(MV2120_GPIO_RTC_IRQ);
++		else
++			gpio_free(MV2120_GPIO_RTC_IRQ);
++	}
++	i2c_register_board_info(0, &mv2120_i2c_rtc, 1);
++
++	/* register mv2120 specific power-off method */
++	if (gpio_request(MV2120_GPIO_POWER_OFF, "POWEROFF") != 0 ||
++	    gpio_direction_output(MV2120_GPIO_POWER_OFF, 1) != 0)
++		pr_err("mv2120: failed to setup power-off GPIO\n");
++	pm_power_off = mv2120_power_off;
++}
++
++/* Warning: HP uses a wrong mach-type (=526) in their bootloader */
++MACHINE_START(MV2120, "HP Media Vault mv2120")
++	/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
++	.phys_io	= ORION5X_REGS_PHYS_BASE,
++	.io_pg_offst	= ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
++	.boot_params	= 0x00000100,
++	.init_machine	= mv2120_init,
++	.map_io		= orion5x_map_io,
++	.init_irq	= orion5x_init_irq,
++	.timer		= &orion5x_timer,
++	.fixup		= tag_fixup_mem32
++MACHINE_END
diff --git a/target/linux/orion/patches/019-add_technologic_systems_ts-78xx_support.patch b/target/linux/orion/patches/019-add_technologic_systems_ts-78xx_support.patch
new file mode 100644
index 0000000..a74464c
--- /dev/null
+++ b/target/linux/orion/patches/019-add_technologic_systems_ts-78xx_support.patch
@@ -0,0 +1,305 @@
+Hi,
+
+The following patch series adds support for the Technologic Systems 
+TS-7800[1].  This is an updated driver to the one I posted before[2] which 
+takes on all the advice and fixes suggested here.
+
+Cheers
+
+Alex
+
+Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
+
+[1] http://www.embeddedarm.com/products/board-detail.php?product=TS-7800
+[2] http://lists.arm.linux.org.uk/lurker/message/20080522.190133.54887e96.en.html
+
+---
+ arch/arm/mach-orion5x/Kconfig        |    7 +
+ arch/arm/mach-orion5x/Makefile       |    1 +
+ arch/arm/mach-orion5x/ts78xx-setup.c |  257 ++++++++++++++++++++++++++++++++++
+ 3 files changed, 265 insertions(+), 0 deletions(-)
+ create mode 100644 arch/arm/mach-orion5x/ts78xx-setup.c
+
+--- a/arch/arm/mach-orion5x/Kconfig
++++ b/arch/arm/mach-orion5x/Kconfig
+@@ -62,6 +62,13 @@
+ 	  Say 'Y' here if you want your kernel to support the
+ 	  HP Media Vault mv2120 or mv5100.
+ 
++config MACH_TS78XX
++	bool "Technologic Systems TS-78xx"
++	select CPU_FEROCEON_OLD_ID
++	help
++	  Say 'Y' here if you want your kernel to support the
++	  Technologic Systems TS-78xx platform.
++
+ endmenu
+ 
+ endif
+--- a/arch/arm/mach-orion5x/Makefile
++++ b/arch/arm/mach-orion5x/Makefile
+@@ -8,3 +8,4 @@
+ obj-$(CONFIG_MACH_TS409)	+= ts409-setup.o
+ obj-$(CONFIG_MACH_WRT350N_V2)	+= wrt350n-v2-setup.o
+ obj-$(CONFIG_MACH_MV2120)	+= mv2120-setup.o
++obj-$(CONFIG_MACH_TS78XX)	+= ts78xx-setup.o
+--- /dev/null
++++ b/arch/arm/mach-orion5x/ts78xx-setup.c
+@@ -0,0 +1,257 @@
++/*
++ * arch/arm/mach-orion5x/ts78xx-setup.c
++ *
++ * Maintainer: Alexander Clouter <alex@digriz.org.uk>
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2.  This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/mtd/physmap.h>
++#include <linux/mv643xx_eth.h>
++#include <linux/ata_platform.h>
++#include <linux/m48t86.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/map.h>
++#include <asm/arch/orion5x.h>
++#include "common.h"
++#include "mpp.h"
++
++/*****************************************************************************
++ * TS-78xx Info
++ ****************************************************************************/
++
++/*
++ * FPGA - lives where the PCI bus would be at ORION5X_PCI_MEM_PHYS_BASE
++ */
++#define	TS78XX_FPGA_REGS_PHYS_BASE	0xe8000000
++#define	TS78XX_FPGA_REGS_VIRT_BASE	0xff900000
++#define	TS78XX_FPGA_REGS_SIZE		SZ_1M
++
++#define	TS78XX_FPGA_REGS_RTC_CTRL	TS78XX_FPGA_REGS_VIRT_BASE | 0x808
++#define	TS78XX_FPGA_REGS_RTC_DATA	TS78XX_FPGA_REGS_VIRT_BASE | 0x80c
++
++/*
++ * 512kB NOR flash Device
++ */
++#define	TS78XX_NOR_BOOT_BASE		0xff800000
++#define	TS78XX_NOR_BOOT_SIZE		SZ_512K
++
++/*****************************************************************************
++ * I/O Address Mapping
++ ****************************************************************************/
++static struct map_desc ts78xx_io_desc[] __initdata = {
++	{
++		.virtual	= TS78XX_FPGA_REGS_VIRT_BASE,
++		.pfn		= __phys_to_pfn(TS78XX_FPGA_REGS_PHYS_BASE),
++		.length		= TS78XX_FPGA_REGS_SIZE,
++		.type		= MT_DEVICE,
++	},
++};
++
++void __init ts78xx_map_io(void)
++{
++	orion5x_map_io();
++	iotable_init(ts78xx_io_desc, ARRAY_SIZE(ts78xx_io_desc));
++}
++
++/*****************************************************************************
++ * 512kB NOR Boot Flash - the chip is a M25P40
++ ****************************************************************************/
++static struct mtd_partition ts78xx_nor_boot_flash_resources[] = {
++	{
++		.name		= "ts-bootrom",
++		.offset		= 0,
++		/* only the first 256kB is used */
++		.size		= SZ_256K,
++		.mask_flags	= MTD_WRITEABLE,
++	},
++};
++
++static struct physmap_flash_data ts78xx_nor_boot_flash_data = {
++	.width		= 1,
++	.parts		= ts78xx_nor_boot_flash_resources,
++	.nr_parts	= ARRAY_SIZE(ts78xx_nor_boot_flash_resources),
++};
++
++static struct resource ts78xx_nor_boot_flash_resource = {
++	.flags		= IORESOURCE_MEM,
++	.start		= TS78XX_NOR_BOOT_BASE,
++	.end		= TS78XX_NOR_BOOT_BASE + TS78XX_NOR_BOOT_SIZE - 1,
++};
++
++static struct platform_device ts78xx_nor_boot_flash = {
++	.name		= "physmap-flash",
++	.id		= -1,
++	.dev		= {
++		.platform_data	= &ts78xx_nor_boot_flash_data,
++	},
++	.num_resources	= 1,
++	.resource	= &ts78xx_nor_boot_flash_resource,
++};
++
++/*****************************************************************************
++ * PCI
++ ****************************************************************************/
++
++/*
++ * WARNING: TS shunt the PCI IO via the FPGA so that you could build soft-PCI
++ * 		devices for it and what-not.  There is nothing on the PCI or
++ * 		PCIe buses so probably nothing really to do yet here, if ever
++ */
++
++/*****************************************************************************
++ * Ethernet
++ ****************************************************************************/
++static struct mv643xx_eth_platform_data ts78xx_eth_data = {
++	.phy_addr	= 0,
++	.force_phy_addr = 1,
++};
++
++/*****************************************************************************
++ * RTC M48T86 - nicked^Wborrowed from arch/arm/mach-ep93xx/ts72xx.c
++ ****************************************************************************/
++static unsigned char ts78xx_rtc_readbyte(unsigned long addr)
++{
++	writeb(addr, TS78XX_FPGA_REGS_RTC_CTRL);
++	return readb(TS78XX_FPGA_REGS_RTC_DATA);
++}
++
++static void ts78xx_rtc_writebyte(unsigned char value, unsigned long addr)
++{
++	writeb(addr, TS78XX_FPGA_REGS_RTC_CTRL);
++	writeb(value, TS78XX_FPGA_REGS_RTC_DATA);
++}
++
++static struct m48t86_ops ts78xx_rtc_ops = {
++	.readbyte	= ts78xx_rtc_readbyte,
++	.writebyte	= ts78xx_rtc_writebyte,
++};
++
++static struct platform_device ts78xx_rtc_device = {
++	.name		= "rtc-m48t86",
++	.id		= -1,
++	.dev		= {
++		.platform_data	= &ts78xx_rtc_ops,
++	},
++	.num_resources	= 0,
++};
++
++/*****************************************************************************
++ * SATA
++ ****************************************************************************/
++static struct mv_sata_platform_data ts78xx_sata_data = {
++	.n_ports	= 2,
++};
++
++/*****************************************************************************
++ * General Setup
++ ****************************************************************************/
++static void __init ts78xx_init(void)
++{
++#ifdef CONFIG_RTC_DRV_M48T86
++	unsigned char tmp_rtc0, tmp_rtc1;
++#endif
++
++	/*
++	 * Setup basic Orion functions. Need to be called early.
++	 */
++	orion5x_init();
++
++	orion5x_mpp_conf(0, MPP_UNUSED);
++
++	/*
++	 * MPP[1] JTAG Clock
++	 * MPP[2] JTAG Data In
++	 * MPP[3] Lattice ECP2 256 FPGA - PB2B
++	 * MPP[4] JTAG Data Out
++	 * MPP[5] JTAG TMS
++	 * MPP[6] Lattice ECP2 256 FPGA - PB31A_CLK4+
++	 * MPP[7] Lattice ECP2 256 FPGA - PB22B
++	 */
++
++	orion5x_mpp_conf(8, MPP_UNUSED);
++	orion5x_mpp_conf(9, MPP_UNUSED);
++	orion5x_mpp_conf(10, MPP_UNUSED);
++	orion5x_mpp_conf(11, MPP_UNUSED);
++	orion5x_mpp_conf(12, MPP_UNUSED);
++	orion5x_mpp_conf(13, MPP_UNUSED);
++	orion5x_mpp_conf(14, MPP_UNUSED);
++	orion5x_mpp_conf(15, MPP_UNUSED);
++	orion5x_mpp_conf(16, MPP_UART);
++	orion5x_mpp_conf(17, MPP_UART);
++	orion5x_mpp_conf(18, MPP_UART);
++	orion5x_mpp_conf(19, MPP_UART);
++
++	/*
++	 * MPP[20] PCI Clock Out 1
++	 * MPP[21] PCI Clock Out 0
++	 * MPP[22] Unused
++	 * MPP[23] Unused
++	 * MPP[24] Unused
++	 * MPP[25] Unused
++	 */
++
++	/*
++	 * Configure peripherals.
++	 */
++	orion5x_ehci0_init();
++	orion5x_ehci1_init();
++	orion5x_eth_init(&ts78xx_eth_data);
++	orion5x_sata_init(&ts78xx_sata_data);
++	orion5x_uart0_init();
++	orion5x_uart1_init();
++
++	orion5x_setup_dev_boot_win(TS78XX_NOR_BOOT_BASE,
++				   TS78XX_NOR_BOOT_SIZE);
++	platform_device_register(&ts78xx_nor_boot_flash);
++
++#ifdef CONFIG_RTC_DRV_M48T86
++	/*
++	 * TS uses some of the user storage space on the RTC chip so see if it
++	 * is present; as it's an optional feature at purchase time and not all
++	 * boards will have it present
++	 *
++	 * I've used the method TS use in their rtc7800.c example for the
++	 * detection logic; a little 'funky' but thats what floats my boat
++	 *
++	 * TODO: track down a guinea pig without an RTC to see if we can work
++	 * 		out a better RTC detection routine
++	 */
++	tmp_rtc0 = ts78xx_rtc_readbyte(126);
++	tmp_rtc1 = ts78xx_rtc_readbyte(127);
++
++	ts78xx_rtc_writebyte(0x00, 126);
++	ts78xx_rtc_writebyte(0x55, 127);
++	if (ts78xx_rtc_readbyte(127) == 0x55) {
++		ts78xx_rtc_writebyte(0xaa, 127);
++		if (ts78xx_rtc_readbyte(127) == 0xaa
++				&& ts78xx_rtc_readbyte(126) == 0x00) {
++			ts78xx_rtc_writebyte(tmp_rtc0, 126);
++			ts78xx_rtc_writebyte(tmp_rtc1, 127);
++			platform_device_register(&ts78xx_rtc_device);
++			goto rtcok;
++		}
++	}
++	printk(KERN_INFO "TS-78xx RTC not detected\n");
++
++ rtcok:
++	;
++#endif
++}
++
++MACHINE_START(TS78XX, "Technologic Systems TS-78xx SBC")
++	/* Maintainer: Alexander Clouter <alex@digriz.org.uk> */
++	.phys_io	= ORION5X_REGS_PHYS_BASE,
++	.io_pg_offst	= ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
++	.boot_params	= 0x00000100,
++	.init_machine	= ts78xx_init,
++	.map_io		= ts78xx_map_io,
++	.init_irq	= orion5x_init_irq,
++	.timer		= &orion5x_timer,
++MACHINE_END