ppc40x: remove 3.6 support

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35104

9 files changed, 0 insertions, 2087 deletions

diff --git a/target/linux/ppc40x/config-3.6 b/target/linux/ppc40x/config-3.6
deleted file mode 100644
index 978a054..0000000
--- a/target/linux/ppc40x/config-3.6
+++ /dev/null
@@ -1,225 +0,0 @@
-CONFIG_405EP=y
-CONFIG_405EX=y
-CONFIG_40x=y
-# CONFIG_44x is not set
-CONFIG_4xx=y
-CONFIG_4xx_SOC=y
-# CONFIG_ACADIA is not set
-# CONFIG_ADVANCED_OPTIONS is not set
-CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
-CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_ILOG2_U32=y
-CONFIG_ARCH_HAS_WALK_MEMORY=y
-CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MAY_HAVE_PC_FDC=y
-# CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set
-# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
-CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
-CONFIG_ARCH_SUPPORTS_MSI=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
-CONFIG_AUDIT_ARCH=y
-CONFIG_BOUNCE=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd"
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CONSISTENT_SIZE=0x00200000
-CONFIG_DECOMPRESS_LZMA=y
-# CONFIG_DEFAULT_UIMAGE is not set
-CONFIG_DTC=y
-# CONFIG_E200 is not set
-CONFIG_EARLY_PRINTK=y
-# CONFIG_EP405 is not set
-# CONFIG_EPAPR_BOOT is not set
-CONFIG_EXTRA_TARGETS="uImage"
-# CONFIG_FSL_ULI1575 is not set
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_ISA_DMA=y
-CONFIG_GENERIC_NVRAM=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-# CONFIG_GENERIC_TBSYNC is not set
-CONFIG_GENERIC_TIME_VSYSCALL=y
-# CONFIG_GEN_RTC is not set
-# CONFIG_GE_FPGA is not set
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-# CONFIG_HAS_RAPIDIO is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IOREMAP_PROT=y
-CONFIG_HAVE_IRQ_WORK=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-# CONFIG_HOTFOOT is not set
-CONFIG_HW_RANDOM=y
-CONFIG_HZ=250
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-CONFIG_IBM_EMAC=y
-CONFIG_IBM_EMAC_EMAC4=y
-CONFIG_IBM_EMAC_POLL_WEIGHT=32
-CONFIG_IBM_EMAC_RGMII=y
-CONFIG_IBM_EMAC_RXB=256
-CONFIG_IBM_EMAC_RX_COPY_THRESHOLD=256
-CONFIG_IBM_EMAC_RX_SKB_HEADROOM=0
-CONFIG_IBM_EMAC_TXB=256
-CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_IOMMU_HELPER is not set
-# CONFIG_IPIC is not set
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_ISA_DMA_API=y
-CONFIG_KERNEL_START=0xc0000000
-CONFIG_KILAUEA=y
-CONFIG_LEDS_GPIO=m
-CONFIG_LOWMEM_SIZE=0x30000000
-CONFIG_MAGICBOX=y
-# CONFIG_MAKALU is not set
-# CONFIG_MATH_EMULATION is not set
-CONFIG_MAX_ACTIVE_REGIONS=32
-# CONFIG_MMIO_NVRAM is not set
-# CONFIG_MPIC is not set
-# CONFIG_MPIC_U3_HT_IRQS is not set
-# CONFIG_MPIC_WEIRD is not set
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-# CONFIG_MTD_CFI_INTELEXT is not set
-CONFIG_MTD_OF_PARTS=y
-CONFIG_MTD_PHYSMAP_OF=y
-CONFIG_NEED_DMA_MAP_STATE=y
-# CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK is not set
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NEED_SG_DMA_LENGTH=y
-CONFIG_NLS=m
-# CONFIG_NONSTATIC_KERNEL is not set
-CONFIG_NOT_COHERENT_CACHE=y
-CONFIG_NR_IRQS=512
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_DEVICE=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_MTD=y
-CONFIG_OF_NET=y
-CONFIG_OF_PCI=y
-CONFIG_OF_PCI_IRQ=y
-CONFIG_OPENRB=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PAGE_OFFSET=0xc0000000
-CONFIG_PCI=y
-CONFIG_PCIEAER=y
-CONFIG_PCIEPORTBUS=y
-CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_MSI=y
-CONFIG_PHYSICAL_START=0x00000000
-CONFIG_PPC=y
-CONFIG_PPC32=y
-CONFIG_PPC40x_SIMPLE=y
-CONFIG_PPC4xx_MSI=y
-CONFIG_PPC4xx_PCI_EXPRESS=y
-# CONFIG_PPC64 is not set
-# CONFIG_PPC_85xx is not set
-# CONFIG_PPC_8xx is not set
-# CONFIG_PPC_970_NAP is not set
-CONFIG_PPC_ADV_DEBUG_DACS=2
-CONFIG_PPC_ADV_DEBUG_DVCS=0
-CONFIG_PPC_ADV_DEBUG_IACS=2
-CONFIG_PPC_ADV_DEBUG_REGS=y
-# CONFIG_PPC_BOOK3S_32 is not set
-# CONFIG_PPC_CELL is not set
-# CONFIG_PPC_CELL_NATIVE is not set
-# CONFIG_PPC_CLOCK is not set
-CONFIG_PPC_DCR=y
-# CONFIG_PPC_DCR_MMIO is not set
-CONFIG_PPC_DCR_NATIVE=y
-# CONFIG_PPC_EARLY_DEBUG is not set
-# CONFIG_PPC_EPAPR_HV_PIC is not set
-# CONFIG_PPC_I8259 is not set
-# CONFIG_PPC_ICP_HV is not set
-# CONFIG_PPC_ICP_NATIVE is not set
-# CONFIG_PPC_ICS_RTAS is not set
-CONFIG_PPC_INDIRECT_PCI=y
-CONFIG_PPC_MMU_NOHASH=y
-# CONFIG_PPC_MM_SLICES is not set
-# CONFIG_PPC_MPC106 is not set
-CONFIG_PPC_MSI_BITMAP=y
-CONFIG_PPC_OF=y
-# CONFIG_PPC_P7_NAP is not set
-CONFIG_PPC_PCI_CHOICE=y
-# CONFIG_PPC_RTAS is not set
-CONFIG_PPC_UDBG_16550=y
-CONFIG_PPC_WERROR=y
-# CONFIG_PPC_WSP is not set
-# CONFIG_PPC_XICS is not set
-# CONFIG_PQ2ADS is not set
-# CONFIG_PREEMPT_RCU is not set
-CONFIG_PROC_DEVICETREE=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_SCHED_HRTICK=y
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250_DETECT_IRQ is not set
-CONFIG_SERIAL_8250_EXTENDED=y
-CONFIG_SERIAL_8250_FSL=y
-# CONFIG_SERIAL_8250_MANY_PORTS is not set
-# CONFIG_SERIAL_8250_RSA is not set
-CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_OF_PLATFORM=y
-# CONFIG_SLAB is not set
-CONFIG_SLUB=y
-CONFIG_SPARSE_IRQ=y
-# CONFIG_SWIOTLB is not set
-CONFIG_TASK_SIZE=0xc0000000
-CONFIG_USB=m
-CONFIG_USB_ARCH_HAS_XHCI=y
-CONFIG_USB_COMMON=m
-# CONFIG_USB_EHCI_HCD is not set
-CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
-CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
-CONFIG_USB_OHCI_HCD=m
-CONFIG_USB_OHCI_HCD_PCI=y
-# CONFIG_USB_OHCI_HCD_PLATFORM is not set
-CONFIG_USB_OHCI_HCD_PPC_OF=y
-CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
-CONFIG_USB_SUPPORT=y
-# CONFIG_USB_UHCI_HCD is not set
-# CONFIG_WALNUT is not set
-CONFIG_WORD_SIZE=32
-# CONFIG_XILINX_SYSACE is not set
-# CONFIG_XILINX_VIRTEX_GENERIC_BOARD is not set
diff --git a/target/linux/ppc40x/patches-3.6/001-powerpc-add-missing-NULL-terminator-to-avoid-boot-pa.patch b/target/linux/ppc40x/patches-3.6/001-powerpc-add-missing-NULL-terminator-to-avoid-boot-pa.patch
deleted file mode 100644
index 0bb2860..0000000
--- a/target/linux/ppc40x/patches-3.6/001-powerpc-add-missing-NULL-terminator-to-avoid-boot-pa.patch
+++ /dev/null
@@ -1,53 +0,0 @@
-From 107b76e67aa0447fc4ea5594823f8ffd2699fbc7 Mon Sep 17 00:00:00 2001
-From: Gabor Juhos <juhosg@openwrt.org>
-Date: Thu, 20 Dec 2012 14:22:38 +0100
-Subject: [PATCH] powerpc: add missing NULL terminator to avoid boot panic on
- PPC40x
-
-The missing NULL terminator can cause a panic on
-PPC405 boards during boot:
-
-  Linux/PowerPC load: console=ttyS0,115200 root=/dev/mtdblock1 rootfstype=squashfs,jffs2 noinitrd init=/etc/preinit
-  Finalizing device tree... flat tree at 0x6a5160
-  bootconsole [udbg0] enabled
-  Page fault in user mode with in_atomic() = 1 mm = (null)
-  NIP = c0275f50  MSR = fffffffe
-  Oops: Weird page fault, sig: 11 [#1]
-  PowerPC 40x Platform
-  Modules linked in:
-  NIP: c0275f50 LR: c0275f60 CTR: c0280000
-  REGS: c0275eb0 TRAP: 636f7265   Not tainted  (3.7.1)
-  MSR: fffffffe <VEC,VSX,EE,PR,FP,ME,SE,BE,IR,DR,PMM,RI> CR: c06a6190  XER: 00000001
-  TASK = c02662a8[0] 'swapper' THREAD: c0274000
-  GPR00: c0275ec0 c000c658 c027c4bf 00000000 c0275ee0 c000a0ec c020a1a8 c020a1f0
-  GPR08: c020f631 c020f404 c025f078 c025f080 c0275f10
-   Call Trace:
-   ---[ end trace 31fd0ba7d8756001 ]---
-
-  Kernel panic - not syncing: Attempted to kill the idle task!
-
-The panic happens since commit 9597abe00c1bab2aedce6b49866bf6d1e81c9eed
-(sections: fix section conflicts in arch/powerpc), however the root
-cause of this is that the NULL terminator were not added in commit
-a4f740cf33f7f6c164bbde3c0cdbcc77b0c4997c (of/flattree: Add of_flat_dt_match()
-helper function).
-
-Cc: Grant Likely <grant.likely@secretlab.ca>
-Cc: <stable@vger.kernel.org>
-Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
----
- arch/powerpc/platforms/40x/ppc40x_simple.c |    3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/arch/powerpc/platforms/40x/ppc40x_simple.c
-+++ b/arch/powerpc/platforms/40x/ppc40x_simple.c
-@@ -57,7 +57,8 @@ static const char *board[] __initdata =
- 	"amcc,makalu",
- 	"apm,klondike",
- 	"est,hotfoot",
--	"plathome,obs600"
-+	"plathome,obs600",
-+	NULL
- };
- 
- static int __init ppc40x_probe(void)
diff --git a/target/linux/ppc40x/patches-3.6/003-powerpc-add-EBC_BXCR-defines.patch b/target/linux/ppc40x/patches-3.6/003-powerpc-add-EBC_BXCR-defines.patch
deleted file mode 100644
index 660b8bc..0000000
--- a/target/linux/ppc40x/patches-3.6/003-powerpc-add-EBC_BXCR-defines.patch
+++ /dev/null
@@ -1,27 +0,0 @@
---- a/arch/powerpc/boot/dcr.h
-+++ b/arch/powerpc/boot/dcr.h
-@@ -55,6 +55,14 @@ static const unsigned long sdram_bxcr[]
- #define   EBC_BXCR(n)					  (n)
- #define	    EBC_BXCR_BAS				    0xfff00000
- #define	    EBC_BXCR_BS				  	    0x000e0000
-+#define	      EBC_BXCR_BS_1M				      0x00000000
-+#define	      EBC_BXCR_BS_2M				      0x00020000
-+#define	      EBC_BXCR_BS_4M				      0x00040000
-+#define	      EBC_BXCR_BS_8M				      0x00060000
-+#define	      EBC_BXCR_BS_16M				      0x00080000
-+#define	      EBC_BXCR_BS_32M				      0x000a0000
-+#define	      EBC_BXCR_BS_64M				      0x000c0000
-+#define	      EBC_BXCR_BS_128M				      0x000e0000
- #define	    EBC_BXCR_BANK_SIZE(reg) \
- 	(0x100000 << (((reg) & EBC_BXCR_BS) >> 17))
- #define	    EBC_BXCR_BU				  	    0x00018000
-@@ -63,6 +71,9 @@ static const unsigned long sdram_bxcr[]
- #define	      EBC_BXCR_BU_WO			  	      0x00010000
- #define	      EBC_BXCR_BU_RW			  	      0x00018000
- #define	    EBC_BXCR_BW				  	    0x00006000
-+#define	      EBC_BXCR_BW_8				      0x00000000
-+#define	      EBC_BXCR_BW_16				      0x00002000
-+#define	      EBC_BXCR_BW_32				      0x00006000
- #define   EBC_B0AP					  0x10
- #define   EBC_B1AP					  0x11
- #define   EBC_B2AP					  0x12
diff --git a/target/linux/ppc40x/patches-3.6/004-magicbox.patch b/target/linux/ppc40x/patches-3.6/004-magicbox.patch
deleted file mode 100644
index 559270d..0000000
--- a/target/linux/ppc40x/patches-3.6/004-magicbox.patch
+++ /dev/null
@@ -1,446 +0,0 @@
---- /dev/null
-+++ b/arch/powerpc/boot/cuboot-magicbox.c
-@@ -0,0 +1,98 @@
-+/*
-+ * Old U-boot compatibility for Magicbox boards
-+ *
-+ * Author: Imre Kaloz <kaloz@openwrt.org>
-+ *         Gabor Juhos <juhosg@openwrt.org>
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published
-+ * by the Free Software Foundation.
-+ */
-+
-+#include "ops.h"
-+#include "io.h"
-+#include "dcr.h"
-+#include "stdio.h"
-+#include "4xx.h"
-+#include "44x.h"
-+#include "cuboot.h"
-+
-+#define TARGET_4xx
-+#define TARGET_405EP
-+#include "ppcboot.h"
-+
-+static bd_t bd;
-+
-+static void fixup_perwe(void)
-+{
-+
-+#define DCRN_CPC0_PCI_BASE	0xf9
-+
-+	/* Turn on PerWE instead of PCIINT */
-+	mtdcr(DCRN_CPC0_PCI_BASE,
-+	      mfdcr(DCRN_CPC0_PCI_BASE) | (0x80000000L >> 27));
-+
-+#undef DCRN_CPC0_PCI_BASE
-+}
-+
-+static void fixup_cf_card(void)
-+{
-+
-+#define CF_CS0_BASE	0xff100000
-+#define CF_CS1_BASE	0xff200000
-+
-+	/* PerCS1 (CF's CS0): base 0xff100000, 16-bit, rw */
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B1CR);
-+	mtdcr(DCRN_EBC0_CFGDATA, CF_CS0_BASE | EBC_BXCR_BS_1M |
-+				 EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B1AP);
-+	mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
-+
-+	/* PerCS2 (CF's CS1): base 0xff200000, 16-bit, rw */
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B2CR);
-+	mtdcr(DCRN_EBC0_CFGDATA, CF_CS1_BASE | EBC_BXCR_BS_1M |
-+				 EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B2AP);
-+	mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
-+
-+#undef CF_CS0_BASE
-+#undef CF_CS1_BASE
-+}
-+
-+static void magicbox_fixups(void)
-+{
-+	ibm405ep_fixup_clocks(bd.bi_procfreq / 8);
-+	ibm4xx_sdram_fixup_memsize();
-+
-+	/* Magicbox v1 has only one ethernet, one serial and no
-+	 * CF slot -- detect it using it's fake enet1addr
-+	 */
-+	if ((bd.bi_enet1addr[2] == 0x02) &&
-+	    (bd.bi_enet1addr[3] == 0xfa) &&
-+	    (bd.bi_enet1addr[4] == 0xf0) &&
-+	    (bd.bi_enet1addr[5] == 0x80)) {
-+		void *devp;
-+		devp = finddevice("/plb/opb/ethernet@ef600900");
-+		del_node(devp);
-+		devp = finddevice("/plb/opb/serial@ef600400");
-+		del_node(devp);
-+		devp = finddevice("/plb/ebc/cf_card@ff100000");
-+		del_node(devp);
-+
-+	} else {
-+		fixup_perwe();
-+		fixup_cf_card();
-+	}
-+
-+	dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
-+}
-+
-+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
-+		unsigned long r6, unsigned long r7)
-+{
-+	CUBOOT_INIT();
-+	platform_ops.fixups = magicbox_fixups;
-+	platform_ops.exit = ibm40x_dbcr_reset;
-+	fdt_init(_dtb_start);
-+	serial_console_init();
-+}
---- /dev/null
-+++ b/arch/powerpc/boot/dts/magicbox.dts
-@@ -0,0 +1,285 @@
-+/*
-+ * Device Tree Source for Magicbox boards
-+ *
-+ * Copyright 2008-2009 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright 2009 Gabor Juhos <juhosg@openwrt.org>
-+ *
-+ * Based on walnut.dts
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2.  This program is licensed "as is" without
-+ * any warranty of any kind, whether express or implied.
-+ */
-+
-+/dts-v1/;
-+
-+/ {
-+	#address-cells = <1>;
-+	#size-cells = <1>;
-+	model = "magicbox";
-+	compatible = "magicbox";
-+	dcr-parent = <&{/cpus/cpu@0}>;
-+
-+	aliases {
-+		ethernet0 = &EMAC0;
-+		ethernet1 = &EMAC1;
-+		serial0 = &UART0;
-+		serial1 = &UART1;
-+	};
-+
-+	cpus {
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		cpu@0 {
-+			device_type = "cpu";
-+			model = "PowerPC,405EP";
-+			reg = <0x00000000>;
-+			clock-frequency = <0>; /* Filled in by zImage */
-+			timebase-frequency = <0>; /* Filled in by zImage */
-+			i-cache-line-size = <0x20>;
-+			d-cache-line-size = <0x20>;
-+			i-cache-size = <0x4000>;
-+			d-cache-size = <0x4000>;
-+			dcr-controller;
-+			dcr-access-method = "native";
-+		};
-+	};
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x00000000>; /* Filled in by zImage */
-+	};
-+
-+	UIC0: interrupt-controller {
-+		compatible = "ibm,uic";
-+		interrupt-controller;
-+		cell-index = <0>;
-+		dcr-reg = <0x0c0 0x009>;
-+		#address-cells = <0>;
-+		#size-cells = <0>;
-+		#interrupt-cells = <2>;
-+	};
-+
-+	plb {
-+		compatible = "ibm,plb3";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		ranges;
-+		clock-frequency = <0>; /* Filled in by zImage */
-+
-+		SDRAM0: memory-controller {
-+			compatible = "ibm,sdram-405ep";
-+			dcr-reg = <0x010 0x002>;
-+		};
-+
-+		MAL: mcmal {
-+			compatible = "ibm,mcmal-405ep", "ibm,mcmal";
-+			dcr-reg = <0x180 0x062>;
-+			num-tx-chans = <4>;
-+			num-rx-chans = <2>;
-+			interrupt-parent = <&UIC0>;
-+			interrupts = <
-+				0xb 0x4 /* TXEOB */
-+				0xc 0x4 /* RXEOB */
-+				0xa 0x4 /* SERR */
-+				0xd 0x4 /* TXDE */
-+				0xe 0x4 /* RXDE */>;
-+		};
-+
-+		POB0: opb {
-+			compatible = "ibm,opb-405ep", "ibm,opb";
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+			ranges = <0xef600000 0xef600000 0x00a00000>;
-+			dcr-reg = <0x0a0 0x005>;
-+			clock-frequency = <0>; /* Filled in by zImage */
-+
-+			UART0: serial@ef600300 {
-+				device_type = "serial";
-+				compatible = "ns16550";
-+				reg = <0xef600300 0x00000008>;
-+				virtual-reg = <0xef600300>;
-+				clock-frequency = <0>; /* Filled in by zImage */
-+				current-speed = <115200>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x0 0x4>;
-+			};
-+
-+			UART1: serial@ef600400 {
-+				device_type = "serial";
-+				compatible = "ns16550";
-+				reg = <0xef600400 0x00000008>;
-+				virtual-reg = <0xef600400>;
-+				clock-frequency = <0>; /* Filled in by zImage */
-+				current-speed = <115200>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x1 0x4>;
-+			};
-+
-+			IIC: i2c@ef600500 {
-+				compatible = "ibm,iic-405ep", "ibm,iic";
-+				#address-cells = <1>;
-+				#size-cells = <0>;
-+				reg = <0xef600500 0x00000011>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x2 0x4>;
-+
-+				dtt@48 {
-+					compatible = "national,lm75";
-+					reg = <0x48>;
-+				};
-+
-+				eeprom@50 {
-+					compatible = "at24,24c16";
-+					reg = <0x50>;
-+				};
-+			};
-+
-+			GPIO0: gpio-controller@ef600700 {
-+				compatible = "ibm,ppc4xx-gpio";
-+				reg = <0xef600700 0x00000020>;
-+				#gpio-cells = <2>;
-+				gpio-controller;
-+			};
-+
-+			EMAC0: ethernet@ef600800 {
-+				linux,network-index = <0x0>;
-+				device_type = "network";
-+				compatible = "ibm,emac-405ep", "ibm,emac";
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <
-+					0xf 0x4 /* Ethernet */
-+					0x9 0x4 /* Ethernet Wake Up */>;
-+				local-mac-address = [000000000000]; /* Filled in by zImage */
-+				reg = <0xef600800 0x00000070>;
-+				mal-device = <&MAL>;
-+				mal-tx-channel = <0>;
-+				mal-rx-channel = <0>;
-+				cell-index = <0>;
-+				max-frame-size = <0x5dc>;
-+				rx-fifo-size = <0x1000>;
-+				tx-fifo-size = <0x800>;
-+				phy-mode = "mii";
-+				phy-map = <0x00000000>;
-+			};
-+
-+			EMAC1: ethernet@ef600900 {
-+				linux,network-index = <0x1>;
-+				device_type = "network";
-+				compatible = "ibm,emac-405ep", "ibm,emac";
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <
-+					0x11 0x4 /* Ethernet */
-+					0x09 0x4 /* Ethernet Wake Up */>;
-+				local-mac-address = [000000000000]; /* Filled in by zImage */
-+				reg = <0xef600900 0x00000070>;
-+				mal-device = <&MAL>;
-+				mal-tx-channel = <2>;
-+				mal-rx-channel = <1>;
-+				cell-index = <1>;
-+				max-frame-size = <0x5dc>;
-+				rx-fifo-size = <0x1000>;
-+				tx-fifo-size = <0x800>;
-+				mdio-device = <&EMAC0>;
-+				phy-mode = "mii";
-+				phy-map = <0x00000001>;
-+			};
-+
-+			leds {
-+				compatible = "gpio-leds";
-+				user {
-+					label = "magicbox:red:user";
-+					gpios = <&GPIO0 2 1>;
-+				};
-+			};
-+		};
-+
-+		EBC0: ebc {
-+			compatible = "ibm,ebc-405ep", "ibm,ebc";
-+			dcr-reg = <0x012 0x002>;
-+			#address-cells = <2>;
-+			#size-cells = <1>;
-+			/* The ranges property is supplied by the bootwrapper
-+			 * and is based on the firmware's configuration of the
-+			 * EBC bridge
-+			 */
-+			clock-frequency = <0>; /* Filled in by zImage */
-+
-+			cf_card@ff100000 {
-+				compatible = "magicbox-cf", "pata-magicbox-cf";
-+				reg = <0x00000000 0xff100000 0x00001000
-+				       0x00000000 0xff200000 0x00001000>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x19 0x1 /* IRQ_TYPE_EDGE_RISING */ >;
-+			};
-+
-+			nor_flash@ffc00000 {
-+				compatible = "cfi-flash";
-+				bank-width = <2>;
-+				reg = <0x00000000 0xffc00000 0x00400000>;
-+				#address-cells = <1>;
-+				#size-cells = <1>;
-+				partition0@0 {
-+					label = "linux";
-+					reg = <0x0 0x140000>;
-+				};
-+				partition1@120000 {
-+					label = "rootfs";
-+					reg = <0x140000 0x280000>;
-+				};
-+				partition2@3c0000 {
-+					label = "u-boot";
-+					reg = <0x3c0000 0x30000>;
-+					read-only;
-+				};
-+				partition3@0 {
-+					label = "firmware";
-+					reg = <0x0 0x3c0000>;
-+				};
-+			};
-+		};
-+
-+		PCI0: pci@ec000000 {
-+			device_type = "pci";
-+			#interrupt-cells = <1>;
-+			#size-cells = <2>;
-+			#address-cells = <3>;
-+			compatible = "ibm,plb405ep-pci", "ibm,plb-pci";
-+			primary;
-+			reg = <0xeec00000 0x00000008	/* Config space access */
-+			       0xeed80000 0x00000004	/* IACK */
-+			       0xeed80000 0x00000004	/* Special cycle */
-+			       0xef480000 0x00000040>;	/* Internal registers */
-+
-+			/* Outbound ranges, one memory and one IO,
-+			 * later cannot be changed. Chip supports a second
-+			 * IO range but we don't use it for now
-+			 */
-+			ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x20000000
-+				  0x01000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
-+
-+			/* Inbound 2GB range starting at 0 */
-+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
-+
-+			interrupt-map-mask = <0xf800 0x0 0x0 0x0>;
-+			interrupt-map = <
-+				/* IDSEL 1 */
-+				0x800 0x0 0x0 0x0 &UIC0 0x1c 0x8
-+
-+				/* IDSEL 2 */
-+				0x1000 0x0 0x0 0x0 &UIC0 0x1d 0x8
-+
-+				/* IDSEL 3 */
-+				0x1800 0x0 0x0 0x0 &UIC0 0x1e 0x8
-+
-+				/* IDSEL 4 */
-+				0x2000 0x0 0x0 0x0 &UIC0 0x1f 0x8
-+			>;
-+		};
-+	};
-+
-+	chosen {
-+		linux,stdout-path = "/plb/opb/serial@ef600300";
-+	};
-+};
---- a/arch/powerpc/boot/Makefile
-+++ b/arch/powerpc/boot/Makefile
-@@ -43,6 +43,7 @@ $(obj)/cuboot-hotfoot.o: BOOTCFLAGS += -
- $(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=440
- $(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=440
- $(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
-+$(obj)/cuboot-magicbox.o: BOOTCFLAGS += -mcpu=405
- $(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
- $(obj)/treeboot-iss4xx.o: BOOTCFLAGS += -mcpu=405
- $(obj)/treeboot-currituck.o: BOOTCFLAGS += -mcpu=405
-@@ -78,7 +79,8 @@ src-plat-y := of.c
- src-plat-$(CONFIG_40x) += fixed-head.S ep405.c cuboot-hotfoot.c \
- 				treeboot-walnut.c cuboot-acadia.c \
- 				cuboot-kilauea.c simpleboot.c \
--				virtex405-head.S virtex.c
-+				virtex405-head.S virtex.c \
-+				cuboot-magicbox.c
- src-plat-$(CONFIG_44x) += treeboot-ebony.c cuboot-ebony.c treeboot-bamboo.c \
- 				cuboot-bamboo.c cuboot-sam440ep.c \
- 				cuboot-sequoia.c cuboot-rainier.c \
-@@ -220,6 +222,7 @@ image-$(CONFIG_HOTFOOT)			+= cuImage.hot
- image-$(CONFIG_WALNUT)			+= treeImage.walnut
- image-$(CONFIG_ACADIA)			+= cuImage.acadia
- image-$(CONFIG_OBS600)			+= uImage.obs600
-+image-$(CONFIG_MAGICBOX)		+= cuImage.magicbox
- 
- # Board ports in arch/powerpc/platform/44x/Kconfig
- image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
---- a/arch/powerpc/platforms/40x/Kconfig
-+++ b/arch/powerpc/platforms/40x/Kconfig
-@@ -38,6 +38,16 @@ config KILAUEA
- 	help
- 	  This option enables support for the AMCC PPC405EX evaluation board.
- 
-+config MAGICBOX
-+	bool "Magicbox"
-+	depends on 40x
-+	default n
-+	select PPC40x_SIMPLE
-+	select 405EP
-+	select PCI
-+	help
-+	  This option enables support for the Magicbox boards.
-+
- config MAKALU
- 	bool "Makalu"
- 	depends on 40x
---- a/arch/powerpc/platforms/40x/ppc40x_simple.c
-+++ b/arch/powerpc/platforms/40x/ppc40x_simple.c
-@@ -58,6 +58,7 @@ static const char *board[] __initdata =
- 	"apm,klondike",
- 	"est,hotfoot",
- 	"plathome,obs600",
-+	"magicbox",
- 	NULL
- };
- 
diff --git a/target/linux/ppc40x/patches-3.6/005-openrb.patch b/target/linux/ppc40x/patches-3.6/005-openrb.patch
deleted file mode 100644
index 949ee89..0000000
--- a/target/linux/ppc40x/patches-3.6/005-openrb.patch
+++ /dev/null
@@ -1,447 +0,0 @@
---- /dev/null
-+++ b/arch/powerpc/boot/cuboot-openrb.c
-@@ -0,0 +1,94 @@
-+/*
-+ * Old U-boot compatibility for OpenRB boards
-+ *
-+ * Author: Gabor Juhos <juhosg@openwrt.org>
-+ *         Imre Kaloz <kaloz@openwrt.org>
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published
-+ * by the Free Software Foundation.
-+ */
-+
-+#include "ops.h"
-+#include "io.h"
-+#include "dcr.h"
-+#include "stdio.h"
-+#include "4xx.h"
-+#include "44x.h"
-+#include "cuboot.h"
-+
-+#define TARGET_4xx
-+#define TARGET_405EP
-+#include "ppcboot.h"
-+
-+static bd_t bd;
-+
-+static void fixup_perwe(void)
-+{
-+#define DCRN_CPC0_PCI_BASE	0xf9
-+
-+	/* Turn on PerWE instead of PCIINT */
-+	mtdcr(DCRN_CPC0_PCI_BASE,
-+	      mfdcr(DCRN_CPC0_PCI_BASE) | (0x80000000L >> 27));
-+
-+#undef DCRN_CPC0_PCI_BASE
-+}
-+
-+static void fixup_cf_card(void)
-+{
-+#define CF_CS0_BASE		0xff100000
-+#define CF_CS1_BASE		0xff200000
-+
-+	/* PerCS1 (CF's CS0): base 0xff100000, 16-bit, rw */
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B1CR);
-+	mtdcr(DCRN_EBC0_CFGDATA, CF_CS0_BASE | EBC_BXCR_BS_1M |
-+				 EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B1AP);
-+	mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
-+
-+	/* PerCS2 (CF's CS1): base 0xff200000, 16-bit, rw */
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B2CR);
-+	mtdcr(DCRN_EBC0_CFGDATA, CF_CS1_BASE | EBC_BXCR_BS_1M |
-+				 EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B2AP);
-+	mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
-+
-+#undef CF_CS0_BASE
-+#undef CF_CS1_BASE
-+}
-+
-+static void fixup_isp116x(void)
-+{
-+#define ISP116X_CS_BASE		0xf0000000
-+
-+	/* PerCS3 (ISP1160's CS): base 0xf0000000, size 32MB, 16-bit, rw */
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B3CR);
-+	mtdcr(DCRN_EBC0_CFGDATA, ISP116X_CS_BASE | EBC_BXCR_BS_32M |
-+				 EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
-+	mtdcr(DCRN_EBC0_CFGADDR, EBC_B3AP);
-+	mtdcr(DCRN_EBC0_CFGDATA, 0x03016600);
-+
-+#undef ISP116X_CS_BASE
-+}
-+
-+static void openrb_fixups(void)
-+{
-+	ibm405ep_fixup_clocks(bd.bi_procfreq / 8);
-+	ibm4xx_sdram_fixup_memsize();
-+
-+	fixup_perwe();
-+	fixup_cf_card();
-+	fixup_isp116x();
-+
-+	dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
-+}
-+
-+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
-+		unsigned long r6, unsigned long r7)
-+{
-+	CUBOOT_INIT();
-+	platform_ops.fixups = openrb_fixups;
-+	platform_ops.exit = ibm40x_dbcr_reset;
-+	fdt_init(_dtb_start);
-+	serial_console_init();
-+}
---- /dev/null
-+++ b/arch/powerpc/boot/dts/openrb.dts
-@@ -0,0 +1,291 @@
-+/*
-+ * Device Tree Source for OpenRB boards
-+ *
-+ * Copyright 2009 Gabor Juhos <juhosg@openwrt.org>
-+ * Copyright 2009 Imre Kaloz <kaloz@openwrt.org>
-+ *
-+ * Based on walnut.dts
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2.  This program is licensed "as is" without
-+ * any warranty of any kind, whether express or implied.
-+ */
-+
-+/dts-v1/;
-+
-+/ {
-+	#address-cells = <1>;
-+	#size-cells = <1>;
-+	model = "openrb";
-+	compatible = "openrb";
-+	dcr-parent = <&{/cpus/cpu@0}>;
-+
-+	aliases {
-+		ethernet0 = &EMAC0;
-+		ethernet1 = &EMAC1;
-+		serial0 = &UART0;
-+		serial1 = &UART1;
-+	};
-+
-+	cpus {
-+		#address-cells = <1>;
-+		#size-cells = <0>;
-+
-+		cpu@0 {
-+			device_type = "cpu";
-+			model = "PowerPC,405EP";
-+			reg = <0x00000000>;
-+			clock-frequency = <0>; /* Filled in by zImage */
-+			timebase-frequency = <0>; /* Filled in by zImage */
-+			i-cache-line-size = <0x20>;
-+			d-cache-line-size = <0x20>;
-+			i-cache-size = <0x4000>;
-+			d-cache-size = <0x4000>;
-+			dcr-controller;
-+			dcr-access-method = "native";
-+		};
-+	};
-+
-+	memory {
-+		device_type = "memory";
-+		reg = <0x00000000 0x00000000>; /* Filled in by zImage */
-+	};
-+
-+	UIC0: interrupt-controller {
-+		compatible = "ibm,uic";
-+		interrupt-controller;
-+		cell-index = <0>;
-+		dcr-reg = <0x0c0 0x009>;
-+		#address-cells = <0>;
-+		#size-cells = <0>;
-+		#interrupt-cells = <2>;
-+	};
-+
-+	plb {
-+		compatible = "ibm,plb3";
-+		#address-cells = <1>;
-+		#size-cells = <1>;
-+		ranges;
-+		clock-frequency = <0>; /* Filled in by zImage */
-+
-+		SDRAM0: memory-controller {
-+			compatible = "ibm,sdram-405ep";
-+			dcr-reg = <0x010 0x002>;
-+		};
-+
-+		MAL: mcmal {
-+			compatible = "ibm,mcmal-405ep", "ibm,mcmal";
-+			dcr-reg = <0x180 0x062>;
-+			num-tx-chans = <4>;
-+			num-rx-chans = <2>;
-+			interrupt-parent = <&UIC0>;
-+			interrupts = <
-+				0xb 0x4 /* TXEOB */
-+				0xc 0x4 /* RXEOB */
-+				0xa 0x4 /* SERR */
-+				0xd 0x4 /* TXDE */
-+				0xe 0x4 /* RXDE */>;
-+		};
-+
-+		POB0: opb {
-+			compatible = "ibm,opb-405ep", "ibm,opb";
-+			#address-cells = <1>;
-+			#size-cells = <1>;
-+			ranges = <0xef600000 0xef600000 0x00a00000>;
-+			dcr-reg = <0x0a0 0x005>;
-+			clock-frequency = <0>; /* Filled in by zImage */
-+
-+			UART0: serial@ef600300 {
-+				device_type = "serial";
-+				compatible = "ns16550";
-+				reg = <0xef600300 0x00000008>;
-+				virtual-reg = <0xef600300>;
-+				clock-frequency = <0>; /* Filled in by zImage */
-+				current-speed = <115200>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x0 0x4>;
-+			};
-+
-+			UART1: serial@ef600400 {
-+				device_type = "serial";
-+				compatible = "ns16550";
-+				reg = <0xef600400 0x00000008>;
-+				virtual-reg = <0xef600400>;
-+				clock-frequency = <0>; /* Filled in by zImage */
-+				current-speed = <115200>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x1 0x4>;
-+			};
-+
-+			IIC: i2c@ef600500 {
-+				compatible = "ibm,iic-405ep", "ibm,iic";
-+				#address-cells = <1>;
-+				#size-cells = <0>;
-+				reg = <0xef600500 0x00000011>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x2 0x4>;
-+
-+				eeprom@50 {
-+					compatible = "at24,24c16";
-+					reg = <0x50>;
-+				};
-+			};
-+
-+			GPIO0: gpio-controller@ef600700 {
-+				compatible = "ibm,ppc4xx-gpio";
-+				reg = <0xef600700 0x00000020>;
-+				#gpio-cells = <2>;
-+				gpio-controller;
-+			};
-+
-+			EMAC0: ethernet@ef600800 {
-+				linux,network-index = <0x0>;
-+				device_type = "network";
-+				compatible = "ibm,emac-405ep", "ibm,emac";
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <
-+					0xf 0x4 /* Ethernet */
-+					0x9 0x4 /* Ethernet Wake Up */>;
-+				local-mac-address = [000000000000]; /* Filled in by zImage */
-+				reg = <0xef600800 0x00000070>;
-+				mal-device = <&MAL>;
-+				mal-tx-channel = <0>;
-+				mal-rx-channel = <0>;
-+				cell-index = <0>;
-+				max-frame-size = <0x5dc>;
-+				rx-fifo-size = <0x1000>;
-+				tx-fifo-size = <0x800>;
-+				phy-mode = "mii";
-+				phy-map = <0x00000000>;
-+			};
-+
-+			EMAC1: ethernet@ef600900 {
-+				linux,network-index = <0x1>;
-+				device_type = "network";
-+				compatible = "ibm,emac-405ep", "ibm,emac";
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <
-+					0x11 0x4 /* Ethernet */
-+					0x09 0x4 /* Ethernet Wake Up */>;
-+				local-mac-address = [000000000000]; /* Filled in by zImage */
-+				reg = <0xef600900 0x00000070>;
-+				mal-device = <&MAL>;
-+				mal-tx-channel = <2>;
-+				mal-rx-channel = <1>;
-+				cell-index = <1>;
-+				max-frame-size = <0x5dc>;
-+				rx-fifo-size = <0x1000>;
-+				tx-fifo-size = <0x800>;
-+				mdio-device = <&EMAC0>;
-+				phy-mode = "mii";
-+				phy-map = <0x00000001>;
-+			};
-+
-+			leds {
-+				compatible = "gpio-leds";
-+				user {
-+					label = "openrb:green:user";
-+					gpios = <&GPIO0 2 1>;
-+				};
-+			};
-+		};
-+
-+		EBC0: ebc {
-+			compatible = "ibm,ebc-405ep", "ibm,ebc";
-+			dcr-reg = <0x012 0x002>;
-+			#address-cells = <2>;
-+			#size-cells = <1>;
-+			/* The ranges property is supplied by the bootwrapper
-+			 * and is based on the firmware's configuration of the
-+			 * EBC bridge
-+			 */
-+			clock-frequency = <0>; /* Filled in by zImage */
-+
-+			isp116x@f0000000 {
-+				compatible = "isp116x-hcd";
-+				oc_enable;
-+				int_act_high;
-+				int_edge_triggered;
-+				reg = <0x00000000 0xf0000000 0x00000002 /* data */
-+				       0x00000000 0xf1000000 0x00000002 /* addr */ >;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x1b 0x1 /* IRQ_TYPE_EDGE_RISING */ >;
-+			};
-+
-+			cf_card@ff100000 {
-+				compatible = "magicbox-cf", "pata-magicbox-cf";
-+				reg = <0x00000000 0xff100000 0x00001000
-+				       0x00000000 0xff200000 0x00001000>;
-+				interrupt-parent = <&UIC0>;
-+				interrupts = <0x19 0x1 /* IRQ_TYPE_EDGE_RISING */ >;
-+			};
-+
-+			nor_flash@ff800000 {
-+				compatible = "cfi-flash";
-+				bank-width = <2>;
-+				reg = <0x00000000 0xff800000 0x00800000>;
-+				#address-cells = <1>;
-+				#size-cells = <1>;
-+				partition0@0 {
-+					label = "linux";
-+					reg = <0x0 0x140000>;
-+				};
-+				partition1@120000 {
-+					label = "rootfs";
-+					reg = <0x140000 0x680000>;
-+				};
-+				partition2@7c0000 {
-+					label = "u-boot";
-+					reg = <0x7c0000 0x30000>;
-+					read-only;
-+				};
-+				partition3@0 {
-+					label = "firmware";
-+					reg = <0x0 0x7c0000>;
-+				};
-+			};
-+		};
-+
-+		PCI0: pci@ec000000 {
-+			device_type = "pci";
-+			#interrupt-cells = <1>;
-+			#size-cells = <2>;
-+			#address-cells = <3>;
-+			compatible = "ibm,plb405ep-pci", "ibm,plb-pci";
-+			primary;
-+			reg = <0xeec00000 0x00000008	/* Config space access */
-+			       0xeed80000 0x00000004	/* IACK */
-+			       0xeed80000 0x00000004	/* Special cycle */
-+			       0xef480000 0x00000040>;	/* Internal registers */
-+
-+			/* Outbound ranges, one memory and one IO,
-+			 * later cannot be changed. Chip supports a second
-+			 * IO range but we don't use it for now
-+			 */
-+			ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x20000000
-+				  0x01000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
-+
-+			/* Inbound 2GB range starting at 0 */
-+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
-+
-+			interrupt-map-mask = <0xf800 0x0 0x0 0x0>;
-+			interrupt-map = <
-+				/* IDSEL 1 */
-+				0x800 0x0 0x0 0x0 &UIC0 0x1c 0x8
-+
-+				/* IDSEL 2 */
-+				0x1000 0x0 0x0 0x0 &UIC0 0x1d 0x8
-+
-+				/* IDSEL 3 */
-+				0x1800 0x0 0x0 0x0 &UIC0 0x1e 0x8
-+
-+				/* IDSEL 4 */
-+				0x2000 0x0 0x0 0x0 &UIC0 0x1f 0x8
-+			>;
-+		};
-+	};
-+
-+	chosen {
-+		linux,stdout-path = "/plb/opb/serial@ef600300";
-+	};
-+};
---- a/arch/powerpc/boot/Makefile
-+++ b/arch/powerpc/boot/Makefile
-@@ -44,6 +44,7 @@ $(obj)/cuboot-taishan.o: BOOTCFLAGS += -
- $(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=440
- $(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
- $(obj)/cuboot-magicbox.o: BOOTCFLAGS += -mcpu=405
-+$(obj)/cuboot-openrb.o: BOOTCFLAGS += -mcpu=405
- $(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
- $(obj)/treeboot-iss4xx.o: BOOTCFLAGS += -mcpu=405
- $(obj)/treeboot-currituck.o: BOOTCFLAGS += -mcpu=405
-@@ -80,7 +81,7 @@ src-plat-$(CONFIG_40x) += fixed-head.S e
- 				treeboot-walnut.c cuboot-acadia.c \
- 				cuboot-kilauea.c simpleboot.c \
- 				virtex405-head.S virtex.c \
--				cuboot-magicbox.c
-+				cuboot-magicbox.c cuboot-openrb
- src-plat-$(CONFIG_44x) += treeboot-ebony.c cuboot-ebony.c treeboot-bamboo.c \
- 				cuboot-bamboo.c cuboot-sam440ep.c \
- 				cuboot-sequoia.c cuboot-rainier.c \
-@@ -223,6 +224,7 @@ image-$(CONFIG_WALNUT)			+= treeImage.wa
- image-$(CONFIG_ACADIA)			+= cuImage.acadia
- image-$(CONFIG_OBS600)			+= uImage.obs600
- image-$(CONFIG_MAGICBOX)		+= cuImage.magicbox
-+image-$(CONFIG_OPENRB)			+= cuImage.openrb
- 
- # Board ports in arch/powerpc/platform/44x/Kconfig
- image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
---- a/arch/powerpc/platforms/40x/Kconfig
-+++ b/arch/powerpc/platforms/40x/Kconfig
-@@ -48,6 +48,16 @@ config MAGICBOX
- 	help
- 	  This option enables support for the Magicbox boards.
- 
-+config OPENRB
-+	bool "OpenRB"
-+	depends on 40x
-+	default n
-+	select PPC40x_SIMPLE
-+	select 405EP
-+	select PCI
-+	help
-+	  This option enables support for the OpenRB boards.
-+
- config MAKALU
- 	bool "Makalu"
- 	depends on 40x
---- a/arch/powerpc/platforms/40x/ppc40x_simple.c
-+++ b/arch/powerpc/platforms/40x/ppc40x_simple.c
-@@ -59,6 +59,7 @@ static const char *board[] __initdata =
- 	"est,hotfoot",
- 	"plathome,obs600",
- 	"magicbox",
-+	"openrb",
- 	NULL
- };
- 
diff --git a/target/linux/ppc40x/patches-3.6/101-pata-magicbox-cf-driver.patch b/target/linux/ppc40x/patches-3.6/101-pata-magicbox-cf-driver.patch
deleted file mode 100644
index 86960db..0000000
--- a/target/linux/ppc40x/patches-3.6/101-pata-magicbox-cf-driver.patch
+++ /dev/null
@@ -1,433 +0,0 @@
---- a/drivers/ata/Kconfig
-+++ b/drivers/ata/Kconfig
-@@ -144,6 +144,16 @@ config PDC_ADMA
- 
- 	  If unsure, say N.
- 
-+config PATA_MAGICBOX_CF
-+	tristate "Magicbox/OpenRB Compact Flash support"
-+	depends on MAGICBOX || OPENRB
-+	help
-+	  This option enables support for a Compact Flash conected on
-+	  the ppc405ep expansion bus. This driver had been written for
-+	  the Magicbox v2 and OpenRB boards.
-+
-+	  If unsure, say N.
-+
- config PATA_OCTEON_CF
- 	tristate "OCTEON Boot Bus Compact Flash support"
- 	depends on CPU_CAVIUM_OCTEON
---- a/drivers/ata/Makefile
-+++ b/drivers/ata/Makefile
-@@ -82,6 +82,7 @@ obj-$(CONFIG_PATA_AT91)		+= pata_at91.o
- obj-$(CONFIG_PATA_CMD640_PCI)	+= pata_cmd640.o
- obj-$(CONFIG_PATA_ISAPNP)	+= pata_isapnp.o
- obj-$(CONFIG_PATA_IXP4XX_CF)	+= pata_ixp4xx_cf.o
-+obj-$(CONFIG_PATA_MAGICBOX_CF)	+= pata_magicbox_cf.o
- obj-$(CONFIG_PATA_MPIIX)	+= pata_mpiix.o
- obj-$(CONFIG_PATA_NS87410)	+= pata_ns87410.o
- obj-$(CONFIG_PATA_OPTI)		+= pata_opti.o
---- /dev/null
-+++ b/drivers/ata/pata_magicbox_cf.c
-@@ -0,0 +1,401 @@
-+/*
-+ *  PATA/CompactFlash driver for the MagicBox v2/OpenRB boards.
-+ *
-+ *  Copyright (C) 2009,2012 Gabor Juhos <juhosg@openwrt.org>
-+ *
-+ *  Based on the IDE driver by Wojtek Kaniewski <wojtekka@toxygen.net>
-+ *
-+ *  This program is free software; you can redistribute it and/or modify it
-+ *  under the terms of the GNU General Public License version 2 as published
-+ *  by the Free Software Foundation.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/slab.h>
-+#include <linux/types.h>
-+#include <linux/ioport.h>
-+#include <linux/libata.h>
-+#include <linux/irq.h>
-+//#include <linux/of.h>
-+//#include <linux/of_device.h>
-+#include <linux/of_platform.h>
-+#include <scsi/scsi_host.h>
-+
-+#define DRV_DESC	"PATA/CompactFlash driver for Magicbox/OpenRB boards"
-+#define DRV_NAME	"pata_magicbox_cf"
-+#define DRV_VERSION	"0.1.0"
-+
-+#define MAGICBOX_CF_REG_CMD		(2 * ATA_REG_CMD)
-+#define MAGICBOX_CF_REG_DATA		(2 * ATA_REG_DATA)
-+#define MAGICBOX_CF_REG_ERR		(2 * ATA_REG_ERR)
-+#define MAGICBOX_CF_REG_FEATURE 	(2 * ATA_REG_FEATURE)
-+#define MAGICBOX_CF_REG_NSECT		(2 * ATA_REG_NSECT)
-+#define MAGICBOX_CF_REG_LBAL		(2 * ATA_REG_LBAL)
-+#define MAGICBOX_CF_REG_LBAM		(2 * ATA_REG_LBAM)
-+#define MAGICBOX_CF_REG_LBAH		(2 * ATA_REG_LBAH)
-+#define MAGICBOX_CF_REG_DEVICE		(2 * ATA_REG_DEVICE)
-+#define MAGICBOX_CF_REG_STATUS		(2 * ATA_REG_STATUS)
-+#define MAGICBOX_CF_REG_ALTSTATUS	(2 * 6)
-+#define MAGICBOX_CF_REG_CTL		(2 * 6)
-+
-+#define MAGICBOX_CF_MAXPORTS	1
-+
-+struct magicbox_cf_info {
-+	void __iomem	*base;
-+	void __iomem	*ctrl;
-+};
-+
-+static inline u8 magicbox_cf_inb(void __iomem *port)
-+{
-+	return (u8) (readw(port) >> 8) & 0xff;
-+}
-+
-+static inline void magicbox_cf_outb(void __iomem *port, u8 value)
-+{
-+	writew(value << 8, port);
-+}
-+
-+static int magicbox_cf_set_mode(struct ata_link *link,
-+				struct ata_device **error)
-+{
-+	struct ata_device *dev;
-+
-+	ata_for_each_dev(dev, link, ENABLED) {
-+		ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
-+		dev->pio_mode = XFER_PIO_0;
-+		dev->xfer_mode = XFER_PIO_0;
-+		dev->xfer_shift = ATA_SHIFT_PIO;
-+		dev->flags |= ATA_DFLAG_PIO;
-+	}
-+
-+	return 0;
-+}
-+
-+static void magicbox_cf_exec_command(struct ata_port *ap,
-+				     const struct ata_taskfile *tf)
-+{
-+	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
-+
-+	magicbox_cf_outb(ap->ioaddr.command_addr, tf->command);
-+	ata_sff_pause(ap);
-+}
-+
-+static u8 magicbox_cf_check_status(struct ata_port *ap)
-+{
-+	u8 status;
-+
-+	status = magicbox_cf_inb(ap->ioaddr.status_addr);
-+
-+	DPRINTK("ata%u: status 0x%X, from %p\n", ap->print_id, status,
-+		ap->ioaddr.status_addr);
-+
-+	return status;
-+}
-+
-+static u8 magicbox_cf_check_altstatus(struct ata_port *ap)
-+{
-+	u8 altstatus;
-+
-+	altstatus = magicbox_cf_inb(ap->ioaddr.altstatus_addr);
-+
-+	DPRINTK("ata%u: altstatus 0x%X, from %p\n", ap->print_id,
-+		altstatus, ap->ioaddr.altstatus_addr);
-+
-+	return altstatus;
-+}
-+
-+static void magicbox_cf_dev_select(struct ata_port *ap, unsigned int device)
-+{
-+	/* Nothing to do. We are supporting one device only. */
-+}
-+
-+static void magicbox_cf_tf_load(struct ata_port *ap,
-+			        const struct ata_taskfile *tf)
-+{
-+	struct ata_ioports *ioaddr = &ap->ioaddr;
-+	unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
-+
-+	if (tf->ctl != ap->last_ctl) {
-+		magicbox_cf_outb(ioaddr->ctl_addr, tf->ctl);
-+		ap->last_ctl = tf->ctl;
-+		ata_wait_idle(ap);
-+	}
-+
-+	if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
-+		magicbox_cf_outb(ioaddr->feature_addr, tf->hob_feature);
-+		magicbox_cf_outb(ioaddr->nsect_addr, tf->hob_nsect);
-+		magicbox_cf_outb(ioaddr->lbal_addr, tf->hob_lbal);
-+		magicbox_cf_outb(ioaddr->lbam_addr, tf->hob_lbam);
-+		magicbox_cf_outb(ioaddr->lbah_addr, tf->hob_lbah);
-+		VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
-+			tf->hob_feature,
-+			tf->hob_nsect,
-+			tf->hob_lbal,
-+			tf->hob_lbam,
-+			tf->hob_lbah);
-+	}
-+
-+	if (is_addr) {
-+		magicbox_cf_outb(ioaddr->feature_addr, tf->feature);
-+		magicbox_cf_outb(ioaddr->nsect_addr, tf->nsect);
-+		magicbox_cf_outb(ioaddr->lbal_addr, tf->lbal);
-+		magicbox_cf_outb(ioaddr->lbam_addr, tf->lbam);
-+		magicbox_cf_outb(ioaddr->lbah_addr, tf->lbah);
-+		VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
-+			tf->feature,
-+			tf->nsect,
-+			tf->lbal,
-+			tf->lbam,
-+			tf->lbah);
-+	}
-+
-+	if (tf->flags & ATA_TFLAG_DEVICE) {
-+		magicbox_cf_outb(ioaddr->device_addr, tf->device);
-+		VPRINTK("device 0x%X\n", tf->device);
-+	}
-+
-+	ata_wait_idle(ap);
-+}
-+
-+static void magicbox_cf_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
-+{
-+	struct ata_ioports *ioaddr = &ap->ioaddr;
-+
-+	tf->command = magicbox_cf_inb(ap->ioaddr.status_addr);
-+	tf->feature = magicbox_cf_inb(ioaddr->error_addr);
-+	tf->nsect = magicbox_cf_inb(ioaddr->nsect_addr);
-+	tf->lbal = magicbox_cf_inb(ioaddr->lbal_addr);
-+	tf->lbam = magicbox_cf_inb(ioaddr->lbam_addr);
-+	tf->lbah = magicbox_cf_inb(ioaddr->lbah_addr);
-+	tf->device = magicbox_cf_inb(ioaddr->device_addr);
-+	VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
-+		tf->feature,
-+		tf->nsect,
-+		tf->lbal,
-+		tf->lbam,
-+		tf->lbah);
-+
-+	if (tf->flags & ATA_TFLAG_LBA48) {
-+		magicbox_cf_outb(ioaddr->ctl_addr, tf->ctl | ATA_HOB);
-+		tf->hob_feature = magicbox_cf_inb(ioaddr->error_addr);
-+		tf->hob_nsect = magicbox_cf_inb(ioaddr->nsect_addr);
-+		tf->hob_lbal = magicbox_cf_inb(ioaddr->lbal_addr);
-+		tf->hob_lbam = magicbox_cf_inb(ioaddr->lbam_addr);
-+		tf->hob_lbah = magicbox_cf_inb(ioaddr->lbah_addr);
-+		magicbox_cf_outb(ioaddr->ctl_addr, tf->ctl);
-+		ap->last_ctl = tf->ctl;
-+		VPRINTK("hob: feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
-+			tf->feature,
-+			tf->nsect,
-+			tf->lbal,
-+			tf->lbam,
-+			tf->lbah);
-+	}
-+}
-+
-+static unsigned int magicbox_cf_data_xfer(struct ata_device *dev,
-+					  unsigned char *buf,
-+					  unsigned int buflen, int rw)
-+{
-+	struct ata_port *ap = dev->link->ap;
-+	unsigned int words = buflen >> 1;
-+	unsigned int i;
-+	u16 *buf16 = (u16 *) buf;
-+	void __iomem *mmio = ap->ioaddr.data_addr;
-+
-+	/* Transfer multiple of 2 bytes */
-+	if (rw == READ)
-+		for (i = 0; i < words; i++)
-+			buf16[i] = readw(mmio);
-+	else
-+		for (i = 0; i < words; i++)
-+			writew(buf16[i], mmio);
-+
-+	/* Transfer trailing 1 byte, if any. */
-+	if (unlikely(buflen & 0x01)) {
-+		u16 align_buf[1] = { 0 };
-+		unsigned char *trailing_buf = buf + buflen - 1;
-+
-+		if (rw == READ) {
-+			align_buf[0] = readw(mmio);
-+			memcpy(trailing_buf, align_buf, 1);
-+		} else {
-+			memcpy(align_buf, trailing_buf, 1);
-+			writew(align_buf[0], mmio);
-+		}
-+		words++;
-+	}
-+
-+	return words << 1;
-+}
-+
-+static void magicbox_cf_irq_on(struct ata_port *ap)
-+{
-+	/* Nothing to do. */
-+}
-+
-+static void magicbox_cf_irq_clear(struct ata_port *ap)
-+{
-+	/* Nothing to do. */
-+}
-+
-+static struct ata_port_operations magicbox_cf_port_ops = {
-+	.inherits		= &ata_sff_port_ops,
-+
-+	.cable_detect		= ata_cable_40wire,
-+	.set_mode		= magicbox_cf_set_mode,
-+
-+	.sff_exec_command	= magicbox_cf_exec_command,
-+	.sff_check_status	= magicbox_cf_check_status,
-+	.sff_check_altstatus	= magicbox_cf_check_altstatus,
-+	.sff_dev_select		= magicbox_cf_dev_select,
-+	.sff_tf_load		= magicbox_cf_tf_load,
-+	.sff_tf_read		= magicbox_cf_tf_read,
-+	.sff_data_xfer		= magicbox_cf_data_xfer,
-+
-+	.sff_irq_on		= magicbox_cf_irq_on,
-+	.sff_irq_clear		= magicbox_cf_irq_clear,
-+
-+	.port_start		= ATA_OP_NULL,
-+};
-+
-+static struct scsi_host_template magicbox_cf_sht = {
-+	ATA_PIO_SHT(DRV_NAME),
-+};
-+
-+static inline void magicbox_cf_setup_port(struct ata_host *host)
-+{
-+	struct magicbox_cf_info *info = host->private_data;
-+	struct ata_port *ap;
-+
-+	ap = host->ports[0];
-+
-+	ap->ops	= &magicbox_cf_port_ops;
-+	ap->pio_mask = ATA_PIO4;
-+	ap->flags |= ATA_FLAG_NO_ATAPI;
-+
-+	ap->ioaddr.cmd_addr = info->base + MAGICBOX_CF_REG_CMD;
-+	ap->ioaddr.data_addr = info->base + MAGICBOX_CF_REG_DATA;
-+	ap->ioaddr.error_addr = info->base + MAGICBOX_CF_REG_ERR;
-+	ap->ioaddr.feature_addr = info->base + MAGICBOX_CF_REG_FEATURE;
-+	ap->ioaddr.nsect_addr = info->base + MAGICBOX_CF_REG_NSECT;
-+	ap->ioaddr.lbal_addr = info->base + MAGICBOX_CF_REG_LBAL;
-+	ap->ioaddr.lbam_addr = info->base + MAGICBOX_CF_REG_LBAM;
-+	ap->ioaddr.lbah_addr = info->base + MAGICBOX_CF_REG_LBAH;
-+	ap->ioaddr.device_addr = info->base + MAGICBOX_CF_REG_DEVICE;
-+	ap->ioaddr.status_addr = info->base + MAGICBOX_CF_REG_STATUS;
-+	ap->ioaddr.command_addr = info->base + MAGICBOX_CF_REG_CMD;
-+
-+	ap->ioaddr.altstatus_addr = info->ctrl + MAGICBOX_CF_REG_ALTSTATUS;
-+	ap->ioaddr.ctl_addr = info->ctrl + MAGICBOX_CF_REG_CTL;
-+
-+	ata_port_desc(ap, "cmd 0x%p ctl 0x%p", ap->ioaddr.cmd_addr,
-+		      ap->ioaddr.ctl_addr);
-+}
-+
-+static int __devinit magicbox_cf_of_probe(struct platform_device *op)
-+{
-+	struct magicbox_cf_info *info;
-+	struct ata_host *host;
-+	int irq;
-+	int ret = 0;
-+
-+	info = kzalloc(sizeof(struct magicbox_cf_info), GFP_KERNEL);
-+	if (info == NULL) {
-+		ret = -ENOMEM;
-+		goto err_exit;
-+	}
-+
-+	irq = irq_of_parse_and_map(op->dev.of_node, 0);
-+	if (irq < 0) {
-+		dev_err(&op->dev, "invalid irq\n");
-+		ret = -EINVAL;
-+		goto err_free_info;
-+	}
-+
-+	info->base = of_iomap(op->dev.of_node, 0);
-+	if (info->base == NULL) {
-+		ret = -ENOMEM;
-+		goto err_free_info;
-+	}
-+
-+	info->ctrl = of_iomap(op->dev.of_node, 1);
-+	if (info->ctrl == NULL) {
-+		ret = -ENOMEM;
-+		goto err_unmap_base;
-+	}
-+
-+	host = ata_host_alloc(&op->dev, MAGICBOX_CF_MAXPORTS);
-+	if (host == NULL) {
-+		ret = -ENOMEM;
-+		goto err_unmap_ctrl;
-+	}
-+
-+	host->private_data = info;
-+	magicbox_cf_setup_port(host);
-+
-+	ret = ata_host_activate(host, irq, ata_sff_interrupt,
-+				IRQF_TRIGGER_RISING, &magicbox_cf_sht);
-+	if (ret)
-+		goto err_unmap_ctrl;
-+
-+	dev_set_drvdata(&op->dev, host);
-+	return 0;
-+
-+ err_unmap_ctrl:
-+	iounmap(info->ctrl);
-+ err_unmap_base:
-+	iounmap(info->base);
-+ err_free_info:
-+	kfree(info);
-+ err_exit:
-+	return ret;
-+}
-+
-+static __devexit int magicbox_cf_of_remove(struct platform_device *op)
-+{
-+	struct ata_host *host = dev_get_drvdata(&op->dev);
-+	struct magicbox_cf_info *info = host->private_data;
-+
-+	ata_host_detach(host);
-+	iounmap(info->ctrl);
-+	iounmap(info->base);
-+	kfree(info);
-+
-+	return 0;
-+}
-+
-+static struct of_device_id magicbox_cf_of_match[] = {
-+	{ .compatible = "pata-magicbox-cf", },
-+	{},
-+};
-+
-+static struct platform_driver magicbox_cf_of_platform_driver = {
-+	.probe		= magicbox_cf_of_probe,
-+	.remove		= __devexit_p(magicbox_cf_of_remove),
-+	.driver		= {
-+		.name = DRV_NAME,
-+		.owner = THIS_MODULE,
-+		.of_match_table = magicbox_cf_of_match,
-+	},
-+};
-+
-+static int __init magicbox_cf_init(void)
-+{
-+	return platform_driver_register(&magicbox_cf_of_platform_driver);
-+}
-+
-+static void __exit magicbox_cf_exit(void)
-+{
-+	platform_driver_unregister(&magicbox_cf_of_platform_driver);
-+}
-+
-+module_init(magicbox_cf_init);
-+module_exit(magicbox_cf_exit);
-+
-+MODULE_DESCRIPTION(DRV_DESC);
-+MODULE_AUTHOR("Gabor Juhos <juhosg@openwrt.org>");
-+MODULE_LICENSE("GPL v2");
-+MODULE_VERSION(DRV_VERSION);
-+MODULE_DEVICE_TABLE(of, magicbox_cf_of_match);
diff --git a/target/linux/ppc40x/patches-3.6/110-kilauea_openwrt_flashmap.patch b/target/linux/ppc40x/patches-3.6/110-kilauea_openwrt_flashmap.patch
deleted file mode 100644
index ab44a2d..0000000
--- a/target/linux/ppc40x/patches-3.6/110-kilauea_openwrt_flashmap.patch
+++ /dev/null
@@ -1,55 +0,0 @@
---- a/arch/powerpc/boot/dts/kilauea.dts
-+++ b/arch/powerpc/boot/dts/kilauea.dts
-@@ -102,8 +102,8 @@
- 			compatible = "ibm,sdram-405ex", "ibm,sdram-4xx-ddr2";
- 			dcr-reg = <0x010 0x002>;
- 			interrupt-parent = <&UIC2>;
--			interrupts = <0x5 0x4	/* ECC DED Error */ 
--				      0x6 0x4>;	/* ECC SEC Error */ 
-+			interrupts = <0x5 0x4	/* ECC DED Error */
-+				      0x6 0x4>;	/* ECC SEC Error */
- 		};
- 
- 		CRYPTO: crypto@ef700000 {
-@@ -157,30 +157,30 @@
- 					reg = <0x00000000 0x00000000 0x04000000>;
- 					#address-cells = <1>;
- 					#size-cells = <1>;
--					partition@0 {
-+					partition0@0 {
- 						label = "kernel";
- 						reg = <0x00000000 0x001e0000>;
- 					};
--					partition@1e0000 {
-+					partition1@1e0000 {
- 						label = "dtb";
- 						reg = <0x001e0000 0x00020000>;
- 					};
--					partition@200000 {
--						label = "root";
--						reg = <0x00200000 0x00200000>;
--					};
--					partition@400000 {
--						label = "user";
--						reg = <0x00400000 0x03b60000>;
-+					partition2@200000 {
-+						label = "rootfs";
-+						reg = <0x00200000 0x03d60000>;
- 					};
--					partition@3f60000 {
-+					partition3@3f60000 {
- 						label = "env";
- 						reg = <0x03f60000 0x00040000>;
- 					};
--					partition@3fa0000 {
-+					partition4@3fa0000 {
- 						label = "u-boot";
- 						reg = <0x03fa0000 0x00060000>;
- 					};
-+					partition5@0 {
-+						label = "firmware";
-+						reg = <0x00000000 0x03f60000>;
-+					};
- 				};
- 
- 				ndfc@1,0 {
diff --git a/target/linux/ppc40x/patches-3.6/120-usb-isp116x-hcd-add-of-binding.patch b/target/linux/ppc40x/patches-3.6/120-usb-isp116x-hcd-add-of-binding.patch
deleted file mode 100644
index f1ad806..0000000
--- a/target/linux/ppc40x/patches-3.6/120-usb-isp116x-hcd-add-of-binding.patch
+++ /dev/null
@@ -1,290 +0,0 @@
---- a/drivers/usb/host/isp116x-hcd.c
-+++ b/drivers/usb/host/isp116x-hcd.c
-@@ -1534,6 +1534,7 @@ static struct hc_driver isp116x_hc_drive
- 
- /*----------------------------------------------------------------*/
- 
-+#ifdef CONFIG_USB_ISP116X_HCD_PLATFORM
- static int isp116x_remove(struct platform_device *pdev)
- {
- 	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-@@ -1710,4 +1711,251 @@ static struct platform_driver isp116x_dr
- 	},
- };
- 
--module_platform_driver(isp116x_driver);
-+static inline int isp116x_platform_register(void)
-+{
-+	return platform_driver_register(&isp116x_driver);
-+}
-+
-+static inline void isp116x_platform_unregister(void)
-+{
-+	platform_driver_unregister(&isp116x_driver);
-+}
-+#else
-+static inline int isp116x_platform_register(void) { return 0; };
-+static void isp116x_platform_unregister(void) {};
-+#endif /* CONFIG_USB_ISP116X_PLATFORM */
-+
-+/*-----------------------------------------------------------------*/
-+
-+#ifdef CONFIG_USB_ISP116X_HCD_OF
-+
-+/* TODO: rework platform probe instead of using a separate probe */
-+
-+#include <linux/of_platform.h>
-+
-+#ifdef USE_PLATFORM_DELAY
-+static void isp116x_of_delay(struct device *ddev, int delay)
-+{
-+	ndelay(delay);
-+}
-+#else
-+#define isp116x_of_delay	NULL
-+#endif
-+
-+static int __devinit isp116x_of_probe(struct platform_device *op)
-+{
-+	struct device_node *dn = op->dev.of_node;
-+	struct usb_hcd *hcd;
-+	struct isp116x *isp116x;
-+	struct resource addr, data;
-+	struct isp116x_platform_data *board;
-+	void __iomem *addr_reg;
-+	void __iomem *data_reg;
-+	int irq;
-+	int ret = 0;
-+	unsigned long irqflags;
-+
-+	ret = of_address_to_resource(dn, 0, &data);
-+	if (ret)
-+		return ret;
-+
-+	ret = of_address_to_resource(dn, 1, &addr);
-+	if (ret)
-+		return ret;
-+
-+	board = kzalloc(sizeof(struct isp116x_platform_data), GFP_KERNEL);
-+	if (board == NULL)
-+		return -ENOMEM;
-+
-+	if (!request_mem_region(addr.start, resource_size(&addr), hcd_name)) {
-+		ret = -EBUSY;
-+		goto err_free_board;
-+	}
-+
-+	addr_reg = ioremap_nocache(addr.start, resource_size(&addr));
-+	if (addr_reg == NULL) {
-+		ret = -ENOMEM;
-+		goto err_release_addr;
-+	}
-+
-+	if (!request_mem_region(data.start, resource_size(&data), hcd_name)) {
-+		ret = -EBUSY;
-+		goto err_unmap_addr;
-+	}
-+
-+	data_reg = ioremap_nocache(data.start, resource_size(&data));
-+	if (data_reg == NULL) {
-+		ret = -ENOMEM;
-+		goto err_release_data;
-+	}
-+
-+	irq = irq_of_parse_and_map(dn, 0);
-+	if (irq == NO_IRQ) {
-+		ret = -EINVAL;
-+		goto err_unmap_data;
-+	}
-+
-+	/* allocate and initialize hcd */
-+	hcd = usb_create_hcd(&isp116x_hc_driver, &op->dev, dev_name(&op->dev));
-+	if (!hcd) {
-+		ret = -ENOMEM;
-+		goto err_irq_dispose;
-+	}
-+
-+	/* this rsrc_start is bogus */
-+	hcd->rsrc_start = addr.start;
-+	isp116x = hcd_to_isp116x(hcd);
-+	isp116x->data_reg = data_reg;
-+	isp116x->addr_reg = addr_reg;
-+	isp116x->board = board;
-+	spin_lock_init(&isp116x->lock);
-+	INIT_LIST_HEAD(&isp116x->async);
-+
-+	board->delay = isp116x_of_delay;
-+	if (of_get_property(dn, "sel15Kres", NULL))
-+		board->sel15Kres = 1;
-+	if (of_get_property(dn, "oc_enable", NULL))
-+		board->oc_enable = 1;
-+	if (of_get_property(dn, "remote_wakeup_enable", NULL))
-+		board->remote_wakeup_enable = 1;
-+
-+	if (of_get_property(dn, "int_act_high", NULL))
-+		board->int_act_high = 1;
-+	if (of_get_property(dn, "int_edge_triggered", NULL))
-+		board->int_edge_triggered = 1;
-+
-+	if (board->int_edge_triggered)
-+		irqflags = board->int_act_high ? IRQF_TRIGGER_RISING :
-+						 IRQF_TRIGGER_FALLING;
-+	else
-+		irqflags = board->int_act_high ? IRQF_TRIGGER_HIGH :
-+						 IRQF_TRIGGER_LOW;
-+
-+	ret = usb_add_hcd(hcd, irq, irqflags | IRQF_DISABLED);
-+	if (ret)
-+		goto err_put_hcd;
-+
-+	ret = create_debug_file(isp116x);
-+	if (ret) {
-+		ERR("Couldn't create debugfs entry\n");
-+		goto err_remove_hcd;
-+	}
-+
-+	return 0;
-+
-+ err_remove_hcd:
-+	usb_remove_hcd(hcd);
-+ err_put_hcd:
-+	usb_put_hcd(hcd);
-+ err_irq_dispose:
-+	irq_dispose_mapping(irq);
-+ err_unmap_data:
-+	iounmap(data_reg);
-+ err_release_data:
-+	release_mem_region(data.start, resource_size(&data));
-+ err_unmap_addr:
-+	iounmap(addr_reg);
-+ err_release_addr:
-+	release_mem_region(addr.start, resource_size(&addr));
-+ err_free_board:
-+	kfree(board);
-+	return ret;
-+}
-+
-+static __devexit int isp116x_of_remove(struct platform_device *op)
-+{
-+	struct usb_hcd *hcd = dev_get_drvdata(&op->dev);
-+	struct isp116x *isp116x;
-+	struct resource res;
-+
-+	if (!hcd)
-+		return 0;
-+
-+	dev_set_drvdata(&op->dev, NULL);
-+
-+	isp116x = hcd_to_isp116x(hcd);
-+	remove_debug_file(isp116x);
-+	usb_remove_hcd(hcd);
-+
-+	irq_dispose_mapping(hcd->irq);
-+
-+	iounmap(isp116x->data_reg);
-+	(void) of_address_to_resource(op->dev.of_node, 0, &res);
-+	release_mem_region(res.start, resource_size(&res));
-+
-+	iounmap(isp116x->addr_reg);
-+	(void) of_address_to_resource(op->dev.of_node, 1, &res);
-+	release_mem_region(res.start, resource_size(&res));
-+
-+	kfree(isp116x->board);
-+	usb_put_hcd(hcd);
-+
-+	return 0;
-+}
-+
-+static struct of_device_id isp116x_of_match[] = {
-+	{ .compatible = "isp116x-hcd", },
-+	{},
-+};
-+
-+static struct platform_driver isp116x_of_platform_driver = {
-+	.probe		= isp116x_of_probe,
-+	.remove		= __devexit_p(isp116x_of_remove),
-+	.driver		= {
-+		.name	= "isp116x-hcd-of",
-+		.owner	= THIS_MODULE,
-+		.of_match_table = isp116x_of_match,
-+	},
-+};
-+
-+static int __init isp116x_of_register(void)
-+{
-+	return platform_driver_register(&isp116x_of_platform_driver);
-+}
-+
-+static void __exit isp116x_of_unregister(void)
-+{
-+	platform_driver_unregister(&isp116x_of_platform_driver);
-+}
-+
-+MODULE_DEVICE_TABLE(of, isp116x_of_match);
-+
-+#else
-+static inline int isp116x_of_register(void) { return 0; };
-+static void isp116x_of_unregister(void) {};
-+#endif /* CONFIG_USB_ISP116X_HCD_OF */
-+
-+/*-----------------------------------------------------------------*/
-+
-+static int __init isp116x_init(void)
-+{
-+	int ret;
-+
-+	if (usb_disabled())
-+		return -ENODEV;
-+
-+	INFO("driver %s, %s\n", hcd_name, DRIVER_VERSION);
-+	ret = isp116x_platform_register();
-+	if (ret)
-+		return ret;
-+
-+	ret = isp116x_of_register();
-+	if (ret)
-+		goto err_platform_unregister;
-+
-+	return 0;
-+
-+ err_platform_unregister:
-+	isp116x_platform_unregister();
-+	return ret;
-+}
-+
-+module_init(isp116x_init);
-+
-+static void __exit isp116x_cleanup(void)
-+{
-+	isp116x_of_unregister();
-+	isp116x_platform_unregister();
-+}
-+
-+module_exit(isp116x_cleanup);
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -260,6 +260,24 @@ config USB_ISP116X_HCD
- 	  To compile this driver as a module, choose M here: the
- 	  module will be called isp116x-hcd.
- 
-+config USB_ISP116X_HCD_PLATFORM
-+	bool "ISP116X support for controllers on platform bus"
-+	depends on USB_ISP116X_HCD
-+	default n if PPC_OF
-+	default y
-+	---help---
-+	  Enables support for the ISP116x USB controller present on the
-+	  platform bus.
-+
-+config USB_ISP116X_HCD_OF
-+	bool "ISP116X support for controllers on OF platform bus"
-+	depends on USB_ISP116X_HCD && PPC_OF
-+	default y if PPC_OF
-+	default n
-+	---help---
-+	  Enables support for the ISP116x USB controller present on the
-+	  OpenFirmware platform bus.
-+
- config USB_ISP1760_HCD
- 	tristate "ISP 1760 HCD support"
- 	depends on USB && EXPERIMENTAL
diff --git a/target/linux/ppc40x/patches-3.6/121-usb-isp116x-hcd-ppc405-register-access.patch b/target/linux/ppc40x/patches-3.6/121-usb-isp116x-hcd-ppc405-register-access.patch
deleted file mode 100644
index c81d18a..0000000
--- a/target/linux/ppc40x/patches-3.6/121-usb-isp116x-hcd-ppc405-register-access.patch
+++ /dev/null
@@ -1,111 +0,0 @@
---- a/drivers/usb/host/isp116x.h
-+++ b/drivers/usb/host/isp116x.h
-@@ -364,22 +364,64 @@ struct isp116x_ep {
- #define	IRQ_TEST()	do{}while(0)
- #endif
- 
-+#ifdef CONFIG_405EP
-+static inline void isp116x_writew(u16 val, void __iomem *addr)
-+{
-+	writew(cpu_to_le16(val), addr);
-+}
-+
-+static inline u16 isp116x_readw(void __iomem *addr)
-+{
-+	return le16_to_cpu(readw(addr));
-+}
-+
-+static inline void isp116x_raw_writew(u16 val, void __iomem *addr)
-+{
-+	writew(cpu_to_le16(val), addr);
-+}
-+
-+static inline u16 isp116x_raw_readw(void __iomem *addr)
-+{
-+	return le16_to_cpu(readw(addr));
-+}
-+#else
-+static inline void isp116x_writew(u16 val, void __iomem *addr)
-+{
-+	writew(val, addr);
-+}
-+
-+static inline u16 isp116x_readw(void __iomem *addr)
-+{
-+	return readw(addr);
-+}
-+
-+static inline void isp116x_raw_writew(u16 val, void __iomem *addr)
-+{
-+	__raw_writew(val, addr);
-+}
-+
-+static inline u16 isp116x_raw_readw(void __iomem *addr)
-+{
-+	return __raw_readw(addr);
-+}
-+#endif
-+
- static inline void isp116x_write_addr(struct isp116x *isp116x, unsigned reg)
- {
- 	IRQ_TEST();
--	writew(reg & 0xff, isp116x->addr_reg);
-+	isp116x_writew(reg & 0xff, isp116x->addr_reg);
- 	isp116x_delay(isp116x, 300);
- }
- 
- static inline void isp116x_write_data16(struct isp116x *isp116x, u16 val)
- {
--	writew(val, isp116x->data_reg);
-+	isp116x_writew(val, isp116x->data_reg);
- 	isp116x_delay(isp116x, 150);
- }
- 
- static inline void isp116x_raw_write_data16(struct isp116x *isp116x, u16 val)
- {
--	__raw_writew(val, isp116x->data_reg);
-+	isp116x_raw_writew(val, isp116x->data_reg);
- 	isp116x_delay(isp116x, 150);
- }
- 
-@@ -387,7 +429,7 @@ static inline u16 isp116x_read_data16(st
- {
- 	u16 val;
- 
--	val = readw(isp116x->data_reg);
-+	val = isp116x_readw(isp116x->data_reg);
- 	isp116x_delay(isp116x, 150);
- 	return val;
- }
-@@ -396,16 +438,16 @@ static inline u16 isp116x_raw_read_data1
- {
- 	u16 val;
- 
--	val = __raw_readw(isp116x->data_reg);
-+	val = isp116x_raw_readw(isp116x->data_reg);
- 	isp116x_delay(isp116x, 150);
- 	return val;
- }
- 
- static inline void isp116x_write_data32(struct isp116x *isp116x, u32 val)
- {
--	writew(val & 0xffff, isp116x->data_reg);
-+	isp116x_writew(val & 0xffff, isp116x->data_reg);
- 	isp116x_delay(isp116x, 150);
--	writew(val >> 16, isp116x->data_reg);
-+	isp116x_writew(val >> 16, isp116x->data_reg);
- 	isp116x_delay(isp116x, 150);
- }
- 
-@@ -413,9 +455,9 @@ static inline u32 isp116x_read_data32(st
- {
- 	u32 val;
- 
--	val = (u32) readw(isp116x->data_reg);
-+	val = (u32) isp116x_readw(isp116x->data_reg);
- 	isp116x_delay(isp116x, 150);
--	val |= ((u32) readw(isp116x->data_reg)) << 16;
-+	val |= ((u32) isp116x_readw(isp116x->data_reg)) << 16;
- 	isp116x_delay(isp116x, 150);
- 	return val;
- }