diff options
| author | Henryk Heisig <hyniu@o2.pl> | 2018-01-28 19:49:38 +0100 |
|---|---|---|
| committer | John Crispin <john@phrozen.org> | 2018-02-11 16:04:16 +0100 |
| commit | 14951e8f8e09ba6e2cff140769189a66155a5345 (patch) | |
| tree | 5a9e873b663e37d6324cda25e3d86032a093ead1 /target/linux/ramips/base-files/etc | |
| parent | e39a240ba28c9081d861a6d4e01a70b61d6097d4 (diff) | |
| download | mtk-20170518-14951e8f8e09ba6e2cff140769189a66155a5345.zip mtk-20170518-14951e8f8e09ba6e2cff140769189a66155a5345.tar.gz mtk-20170518-14951e8f8e09ba6e2cff140769189a66155a5345.tar.bz2 | |
ramips: add support for TP-Link Archer C50 v3
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Flash instruction:
The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Diffstat (limited to 'target/linux/ramips/base-files/etc')
| -rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/01_leds | 6 | ||||
| -rwxr-xr-x | target/linux/ramips/base-files/etc/board.d/02_network | 1 | ||||
| -rw-r--r-- | target/linux/ramips/base-files/etc/diag.sh | 1 |
3 files changed, 8 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 110b588..677bf95 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -393,6 +393,12 @@ tplink,c20-v4) ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:green:wlan2g" "wlan0" ;; +tplink,c50-v3) + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1e" + ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" + ucidef_set_led_netdev "wlan2g" "wlan2g" "$boardname:green:wlan2g" "wlan1" + set_wifi_led "$boardname:green:wlan5g" + ;; tplink,tl-mr3420-v5) set_usb_led "$boardname:green:usb" set_wifi_led "$boardname:green:wlan" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index d385594..d064bfe 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -175,6 +175,7 @@ ramips_setup_interfaces() rb750gr3|\ rt-n14u|\ tplink,c20-v4|\ + tplink,c50-v3|\ tplink,tl-mr3420-v5|\ tl-wr840n-v4|\ tl-wr840n-v5|\ diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index 068df1d..6b11fb2 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -39,6 +39,7 @@ get_status_led() { pwh2004|\ r6220|\ tplink,c20-v4|\ + tplink,c50-v3|\ tplink,tl-mr3420-v5|\ tl-wr840n-v4|\ tl-wr840n-v5|\ |