summaryrefslogtreecommitdiff
path: root/target/linux/ramips/base-files/etc
diff options
context:
space:
mode:
authorRosen Penev <rosenp@gmail.com>2018-02-04 16:24:15 -0800
committerJohn Crispin <john@phrozen.org>2018-02-13 10:01:52 +0100
commitc60a21532bc903ab86d971b478752152d4476ef8 (patch)
tree4c1a4b49aef72a50d4ef72ef3215be1aa96713f4 /target/linux/ramips/base-files/etc
parent2d27ebbb9338c114b3b5403cd4eb6fc05ef1ed6a (diff)
downloadmtk-20170518-c60a21532bc903ab86d971b478752152d4476ef8.zip
mtk-20170518-c60a21532bc903ab86d971b478752152d4476ef8.tar.gz
mtk-20170518-c60a21532bc903ab86d971b478752152d4476ef8.tar.bz2
ramips: Add support for the GnuBee Personal Cloud Two
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com It is a low-cost, low-power, network-attached storage device. Specifications: - SoC: MediaTek MT7621AT - RAM: DDR3 512 MB - Flash: 32 MB - Six SATA ports for 3.5" Drives - One SDcard - One USB 3.0 - Two USB 2.0 - Gigabit Ethernet: Three Ports - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1 - Three GPIOs available on a pin header Flash instructions: The GnuBee Personal Cloud Two ships with libreCMC installed. libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt. As such one can upgrade using the webinterface or sysupgrade. Das U-Boot has multiple options for recovery or updates including : - USB - http - tftp Errata: - While there are three ethernet ports, the third requires support for the second GMAC. This will come in kernel 4.14. - The first hard drive slot has a clearance issue with the two fan headers. Workaround is to pull the headers out and connect the pins to jumper wires. - Using this device as a NAS is problematic with the 4.9 kernel as many /dev/sdX reads throw silent errors. The current theory behind this is some kind of unhandled DMA mapping error in the kernel. This is not an issue with kernel 4.4. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Signed-off-by: Rosen Penev <rosenp@gmail.com>
Diffstat (limited to 'target/linux/ramips/base-files/etc')
-rwxr-xr-xtarget/linux/ramips/base-files/etc/board.d/01_leds6
-rwxr-xr-xtarget/linux/ramips/base-files/etc/board.d/02_network4
-rw-r--r--target/linux/ramips/base-files/etc/diag.sh1
3 files changed, 11 insertions, 0 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 677bf95..573dd31 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -191,6 +191,12 @@ gb-pc1)
ucidef_set_led_switch "lan1" "lan1" "$boardname:green:lan1" "switch0" "0x01"
ucidef_set_led_switch "lan2" "lan2" "$boardname:green:lan2" "switch0" "0x10"
;;
+gb-pc2)
+ ucidef_set_led_switch "lan" "lan" "$board:green:lan" "switch0" "0x01"
+ ucidef_set_led_switch "wan" "wan" "$board:green:wan" "switch0" "0x10"
+ ucidef_set_led_netdev "eth1-g" "eth1-g" "$board:green:eth1-g" "eth1"
+ ucidef_set_led_netdev "eth1-y" "eth1-y" "$board:green:eth1-y" "eth1"
+ ;;
gl-mt300a|\
gl-mt300n|\
gl-mt750)
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index d064bfe..1ccff89 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -206,6 +206,10 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6@eth0"
;;
+ gb-pc2)
+ ucidef_add_switch "switch0" \
+ "4:lan" "0:wan" "6@eth0"
+ ;;
gl-mt300n-v2)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6@eth0"
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 6b11fb2..e38311d 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -91,6 +91,7 @@ get_status_led() {
dir-620-d1|\
dwr-512-b|\
gb-pc1|\
+ gb-pc2|\
hpm|\
hw550-3g|\
mac1200rv2|\