ramips: add support for Buffalo WCR-1166DS

Buffalo WCR-1166DS is a small wireless router with

 - MT7628AN + MT7612E
 - 64MiB DDR2 SDRAM
 - 16MiB SPI flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 2x 10/100M ethernet switch
 - 8x programmable LED
 - 3x button
 - UART pad on PCB (J2: 3.3V, GND, TX, RX)

factory image can be installed via stock web UI.

due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>

4 files changed, 24 insertions, 14 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 91f1aaa..c001dfe 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -263,6 +263,10 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
 		;;
+	wcr-1166ds)
+		ucidef_add_switch "switch0" \
+			"3:lan" "4:wan" "6@eth0"
+		;;
 	wcr-150gn)
 		ucidef_add_switch "switch0" \
 			"0:lan" "6t@eth0"
@@ -410,6 +414,12 @@ ramips_setup_macs()
 		lan_mac=$(cat /sys/class/net/eth0/address)
 		wan_mac=$(macaddr_add "$lan_mac" 5)
 		;;
+	wcr-1166ds|\
+	wsr-1166)
+		local index="$(find_mtd_index "board_data")"
+		wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
+		lan_mac=$wan_mac
+		;;
 	wcr-150gn)
 		wan_mac=$(mtd_get_mac_binary factory 40)
 		;;
@@ -427,11 +437,6 @@ ramips_setup_macs()
 	wlr-6000)
 		wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2)
 		;;
-	wsr-1166)
-		local index="$(find_mtd_index "board_data")"
-		wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
-		lan_mac=$wan_mac
-		;;
 	*)
 		lan_mac=$(cat /sys/class/net/eth0/address)
 		wan_mac=$(macaddr_add "$lan_mac" 1)
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 9499833..5fb2213 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -219,6 +219,12 @@ get_status_led() {
 	zbt-wr8305rt)
 		status_led="$board:green:sys"
 		;;
+	wcr-1166ds|\
+	whr-300hp2|\
+	wsr-1166|\
+	wsr-600)
+		status_led="$board:green:power"
+		;;
 	wcr-150gn|\
 	wl-351)
 		status_led="$board:amber:power"
@@ -233,11 +239,6 @@ get_status_led() {
 	wizfi630a)
 		status_led="$board::run"
 		;;
-	whr-300hp2|\
-	wsr-1166|\
-	wsr-600)
-		status_led="$board:green:power"
-		;;
 	wrtnode2r | \
 	wrtnode2p | \
 	wrtnode)
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 8292da1..d9918cc 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -499,6 +499,9 @@ ramips_board_detect() {
 	*"W502U")
 		name="w502u"
 		;;
+	*"WCR-1166DS")
+		name="wcr-1166ds"
+		;;
 	*"WCR-150GN")
 		name="wcr-150gn"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index c6ad8ca..d83e5c1 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -226,6 +226,11 @@ platform_check_image() {
 		}
 		return 0
 		;;
+	ubnt-erx)
+		nand_do_platform_check "$board" "$1"
+		return $?;
+		;;
+	wcr-1166ds|\
 	wsr-1166)
 		[ "$magic" != "48445230" ] && {
 			echo "Invalid image type."
@@ -233,10 +238,6 @@ platform_check_image() {
 		}
 		return 0
 		;;
-	ubnt-erx)
-		nand_do_platform_check "$board" "$1"
-		return $?;
-		;;
 	esac
 
 	echo "Sysupgrade is not yet supported on $board."