ralink: Add support for samsung cy-swr1100 wireless router

It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.

Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 40908

8 files changed, 25 insertions, 0 deletions

diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 66a0aaa..f9b4168 100755
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -27,6 +27,9 @@ get_status_led() {
 	br6425 | br-6475nd)
 		status_led="edimax:green:power"
 		;;
+	cy-swr1100)
+		status_led="samsung:blue:wps"
+		;;
 	d105)
 		status_led="d105:red:power"
 		;;
diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index 1a39bb6..b57bfd8 100644
--- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -70,6 +70,7 @@ case "$FIRMWARE" in
 	broadway | \
 	br6524n | \
 	carambola | \
+	cy-swr1100 | \
 	d105 | \
 	dcs-930 | \
 	dir-300-b7 | \
@@ -136,6 +137,9 @@ case "$FIRMWARE" in
 
 "rt2x00pci_1_0.eeprom")
 	case $board in
+	cy-swr1100)
+		rt2x00_eeprom_extract "factory" 8192 512
+		;;
 	rt-n56u | whr-600d)
 		rt2x00_eeprom_extract "factory" 32768 512
 		;;
diff --git a/target/linux/ramips/base-files/etc/uci-defaults/01_leds b/target/linux/ramips/base-files/etc/uci-defaults/01_leds
index 74ba0ba..23c2451 100755
--- a/target/linux/ramips/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/ramips/base-files/etc/uci-defaults/01_leds
@@ -60,6 +60,10 @@ case $board in
 	br6524n)
 		set_wifi_led "edimax:blue:wlan"
 		;;
+	cy-swr1100)
+		ucidef_set_led_default "wps" "WPS" "samsung:blue:wps" "0"
+		set_usb_led "samsung:blue:usb"
+		;;
 	d105)
 		ucidef_set_led_default "power" "POWER" "d105:red:power" "1"
 		set_usb_led "d105:green:usb"
diff --git a/target/linux/ramips/base-files/etc/uci-defaults/02_network b/target/linux/ramips/base-files/etc/uci-defaults/02_network
index b66d176..b9524f6 100755
--- a/target/linux/ramips/base-files/etc/uci-defaults/02_network
+++ b/target/linux/ramips/base-files/etc/uci-defaults/02_network
@@ -78,6 +78,13 @@ ramips_setup_interfaces()
 		ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 6t"
 		;;
 
+	cy-swr1100)
+		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+		ucidef_add_switch "switch0" "1" "1"
+		ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 9t"
+		ucidef_add_switch_vlan "switch0" "2" "4 9t"
+		;;
+
 	dir-610-a1 | \
 	dir-300-b7 | \
 	dir-320-b1 | \
@@ -205,6 +212,7 @@ ramips_setup_macs()
 		wan_mac=$(macaddr_add "$lan_mac" 1)
 		;;
 
+	cy-swr1100 | \
 	dir-645)
 		lan_mac=$(mtd_get_mac_ascii nvram lanmac)
 		wan_mac=$(mtd_get_mac_ascii nvram wanmac)
diff --git a/target/linux/ramips/base-files/etc/uci-defaults/09_fix-seama-header b/target/linux/ramips/base-files/etc/uci-defaults/09_fix-seama-header
index d8bed79..a6c392c 100755
--- a/target/linux/ramips/base-files/etc/uci-defaults/09_fix-seama-header
+++ b/target/linux/ramips/base-files/etc/uci-defaults/09_fix-seama-header
@@ -14,6 +14,7 @@ fix_seama_header() {
 board=$(ramips_board_name)
 
 case "$board" in
+cy-swr1100 | \
 dir-645)
 	fix_seama_header kernel
 	;;
diff --git a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac
index 7ff6e3d..8538c13 100644
--- a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac
+++ b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac
@@ -51,6 +51,7 @@ preinit_set_mac_address() {
                 mac=$(mtd_get_mac_binary devdata 16388)
                 ifconfig eth0 hw ether $mac 2>/dev/null
                 ;;
+	cy-swr1100 |\
 	dir-645)
 		mac=$(mtd_get_mac_ascii nvram lanmac)
 		mac=$(macaddr_setbit_la "$mac")
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 4619bef..f9732f8 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -70,6 +70,9 @@ ramips_board_detect() {
 	*"Aztech HW550-3G")
 		name="hw550-3g"
 		;;
+	*"CY-SWR1100")
+		name="cy-swr1100"
+		;;
 	*"DCS-930")
 		name="dcs-930"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index c85ee0f..3fdf625 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -97,6 +97,7 @@ platform_check_image() {
 		}
 		return 0
 		;;
+	cy-swr1100 |\
 	dir-610-a1 |\
 	dir-645)
 		[ "$magic" != "5ea3a417" ] && {