ramips: add support for TP-Link TL-WR840N v5

TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button

* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
  Orange LED is registered so you can later use it for your own purposes.

  Flash instruction:

  Unlike TL-WR840N v4 flashing through WEB UI works in v5.
  1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
  2. Go to 192.168.0.1
  3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
  4. Wait until green LED stops flashing and use the router.

Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.

After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.

Signed-off-by: Robert Marko <robimarko@gmail.com>

4 files changed, 6 insertions, 0 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 1c8505e..62b4123 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -171,6 +171,7 @@ ramips_setup_interfaces()
 	rb750gr3|\
 	rt-n14u|\
 	tl-wr840n-v4|\
+	tl-wr840n-v5|\
 	tl-wr841n-v13|\
 	ubnt-erx|\
 	ubnt-erx-sfp|\
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 3b3c455..dc89e45 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -37,6 +37,7 @@ get_status_led() {
 	pwh2004|\
 	r6220|\
 	tl-wr840n-v4|\
+	tl-wr840n-v5|\
 	tl-wr841n-v13|\
 	vr500|\
 	wnce2001|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 07e776c..43c0f56 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -502,6 +502,9 @@ ramips_board_detect() {
 	*"TL-WR840N v4")
 		name="tl-wr840n-v4"
 		;;
+	*"TL-WR840N v5")
+		name="tl-wr840n-v5"
+		;;
 	*"TL-WR841N v13")
 		name="tl-wr841n-v13"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 99ebe35..84ff11a 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -236,6 +236,7 @@ platform_check_image() {
 	c50|\
 	mr200|\
 	tl-wr840n-v4|\
+	tl-wr840n-v5|\
 	tl-wr841n-v13)
 		[ "$magic" != "03000000" ] && {
 			echo "Invalid image type."