ramips: improve F5D8235 V1 support

This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.

Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.

Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>

4 files changed, 78 insertions, 18 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index f6dbf30..ab077bf 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -158,7 +158,11 @@ ex2700)
 	ucidef_set_led_default "power_r" "POWER (red)" "$board:red:power" "0"
 	set_wifi_led "$board:green:router"
 	;;
-f5d8235-v1|\
+f5d8235-v1)
+	ucidef_set_led_default "lan" "lan" "$board:blue:wired" "0"
+	set_usb_led "$board:blue:storage"
+	set_wifi_led "$board:blue:wireless"
+	;;
 f5d8235-v2)
 	set_usb_led "$board:blue:storage"
 	;;
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index e3e6550..0eaa440 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -130,7 +130,6 @@ ramips_setup_interfaces()
 	c50|\
 	dir-645|\
 	dir-860l-b1|\
-	f5d8235-v1|\
 	f5d8235-v2|\
 	gl-mt300a|\
 	gl-mt300n|\
@@ -236,6 +235,7 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
 		;;
+	f5d8235-v1|\
 	tew-714tru|\
 	v11st-fe|\
 	wzr-agl300nh)
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 6bcdc0f..abbe147 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -126,6 +126,9 @@ get_status_led() {
 	pbr-d1)
 		status_led="$board:orange:power"
 		;;
+	f5d8235-v1)
+		status_led="$board:blue:wired"
+		;;
 	f5d8235-v2)
 		status_led="$board:blue:router"
 		;;
diff --git a/target/linux/ramips/dts/F5D8235_V1.dts b/target/linux/ramips/dts/F5D8235_V1.dts
index 74e423c..4d95860 100644
--- a/target/linux/ramips/dts/F5D8235_V1.dts
+++ b/target/linux/ramips/dts/F5D8235_V1.dts
@@ -2,6 +2,7 @@
 
 #include "rt2880.dtsi"
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 
 / {
@@ -12,7 +13,7 @@
 
 	cfi@1f000000 {
 		compatible = "cfi-flash";
-		reg = <0x1f000000 0x800000>;
+		reg = <0xbc400000 0x800000>;
 		bank-width = <2>;
 		device-width = <2>;
 		#address-cells = <1>;
@@ -37,15 +38,15 @@
 		};
 
 		partition@50000 {
-			label = "linux";
-			reg = <0x50000 0x3b0000>;
+			label = "firmware";
+			reg = <0x50000 0x7b0000>;
 		};
 	};
 
 	rtl8366s {
 		compatible = "realtek,rtl8366s";
-		gpio-sda = <&gpio0 1 0>;
-		gpio-sck = <&gpio0 2 0>;
+		gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+		gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
 	};
 
 	gpio-keys-polled {
@@ -56,13 +57,13 @@
 
 		wps {
 			label = "wps";
-			gpios = <&gpio0 0 1>;
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WPS_BUTTON>;
 		};
 
 		reset {
 			label = "reset";
-			gpios = <&gpio0 9 1>;
+			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
 		};
 	};
@@ -70,14 +71,69 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
+		internet {
+			label = "f5d8235-v1:blue:internet";
+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+		};
+
+		internet2 {
+			label = "f5d8235-v1:amber:internet";
+			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+		};
+
+		modem {
+			label = "f5d8235-v1:blue:modem";
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		};
+
+		modem2 {
+			label = "f5d8235-v1:amber:modem";
+			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		};
+
+		router {
+			label = "f5d8235-v1:blue:router";
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		};
+
 		storage {
 			label = "f5d8235-v1:blue:storage";
-			gpios = <&gpio0 7 1>;
+			gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
 		};
 
 		storage2 {
-			label = "f5d8235-v1:orange:storage";
-			gpios = <&gpio0 8 1>;
+			label = "f5d8235-v1:amber:storage";
+			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+		};
+
+		security {
+			label = "f5d8235-v1:blue:security";
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+
+		security2 {
+			label = "f5d8235-v1:amber:security";
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+
+		wired {
+			label = "f5d8235-v1:blue:wired";
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wired2 {
+			label = "f5d8235-v1:amber:wired";
+			gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+		};
+
+		wireless {
+			label = "f5d8235-v1:blue:wireless";
+			gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		};
+
+		wireless2 {
+			label = "f5d8235-v1:amber:wireless";
+			gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -89,7 +145,7 @@
 &pinctrl {
 	state_default: pinctrl0 {
 		gpio {
-			ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf";
+			ralink,group = "spi", "i2c", "jtag", "mdio", "uartlite";
 			ralink,function = "gpio";
 		};
 	};
@@ -104,10 +160,7 @@
 	};
 };
 
-/* FIXME: no u-boot partition and 0x40000@uboot is out of boundaries */
-/*&wmac {
+&wmac {
 	status = "okay";
-	ralink,mtd-eeprom = <&u-boot 0x40000>;
+	ralink,mtd-eeprom = <&factory 0x0>;
 };
-*/
-