ipq806x/dts: Add Archer C2600 DTS

Signed-off-by: Ash Benz <ash.benz@bk.ru>

1 files changed, 425 insertions, 0 deletions

diff --git a/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch b/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch
new file mode 100644
index 0000000..8952f33
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch
@@ -0,0 +1,425 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -506,6 +506,7 @@
+ 	qcom-apq8084-ifc6540.dtb \
+ 	qcom-apq8084-mtp.dtb \
+ 	qcom-ipq8064-ap148.dtb \
++	qcom-ipq8064-c2600.dtb \
+ 	qcom-ipq8064-db149.dtb \
+ 	qcom-ipq8064-r7500.dtb \
+ 	qcom-ipq8064-d7800.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
+@@ -0,0 +1,412 @@
++#include "qcom-ipq8064-v1.0.dtsi"
++#include <dt-bindings/input/input.h>
++
++/ {
++	model = "TP-Link Archer C2600";
++	compatible = "tplink,c2600", "qcom,ipq8064";
++
++	memory@0 {
++		reg = <0x42000000 0x1e000000>;
++		device_type = "memory";
++	};
++
++	reserved-memory {
++		#address-cells = <1>;
++		#size-cells = <1>;
++		ranges;
++		rsvd@41200000 {
++			reg = <0x41200000 0x300000>;
++			no-map;
++		};
++	};
++
++	aliases {
++		serial0 = &uart4;
++		mdio-gpio0 = &mdio0;
++	};
++
++	chosen {
++		linux,stdout-path = "serial0:115200n8";
++	};
++
++	soc {
++		pinmux@800000 {
++			i2c4_pins: i2c4_pinmux {
++				pins = "gpio12", "gpio13";
++				function = "gsbi4";
++				bias-disable;
++			};
++
++			spi_pins: spi_pins {
++				mux {
++					pins = "gpio18", "gpio19", "gpio21";
++					function = "gsbi5";
++					drive-strength = <10>;
++					bias-none;
++				};
++			};
++
++			nand_pins: nand_pins {
++				mux {
++					pins = "gpio34", "gpio35", "gpio36",
++					       "gpio37", "gpio38", "gpio39",
++					       "gpio40", "gpio41", "gpio42",
++					       "gpio43", "gpio44", "gpio45",
++					       "gpio46", "gpio47";
++					function = "nand";
++					drive-strength = <10>;
++					bias-disable;
++				};
++
++				pullups {
++					pins = "gpio39";
++					bias-pull-up;
++				};
++
++				hold {
++					pins = "gpio40", "gpio41", "gpio42",
++					       "gpio43", "gpio44", "gpio45",
++					       "gpio46", "gpio47";
++					bias-bus-hold;
++				};
++			};
++
++			mdio0_pins: mdio0_pins {
++				mux {
++					pins = "gpio0", "gpio1";
++					function = "gpio";
++					drive-strength = <8>;
++					bias-disable;
++				};
++			};
++
++			rgmii2_pins: rgmii2_pins {
++				mux {
++					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
++					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
++					function = "rgmii2";
++					drive-strength = <8>;
++					bias-disable;
++				};
++			};
++		};
++
++		gsbi@16300000 {
++			qcom,mode = <GSBI_PROT_I2C_UART>;
++			status = "ok";
++			serial@16340000 {
++				status = "ok";
++			};
++			/*
++			 * The i2c device on gsbi4 should not be enabled.
++			 * On ipq806x designs gsbi4 i2c is meant for exclusive
++			 * RPM usage. Turning this on in kernel manifests as
++			 * i2c failure for the RPM.
++			 */
++		};
++
++		gsbi5: gsbi@1a200000 {
++			qcom,mode = <GSBI_PROT_SPI>;
++			status = "ok";
++
++			spi4: spi@1a280000 {
++				status = "ok";
++				spi-max-frequency = <50000000>;
++
++				pinctrl-0 = <&spi_pins>;
++				pinctrl-names = "default";
++
++				cs-gpios = <&qcom_pinmux 20 0>;
++
++				flash: m25p80@0 {
++					compatible = "s25fl256s1";
++					#address-cells = <1>;
++					#size-cells = <1>;
++					spi-max-frequency = <50000000>;
++					reg = <0>;
++
++					SBL1@0 {
++						label = "SBL1";
++						reg = <0x0 0x20000>;
++						read-only;
++					};
++					MIBIB@20000 {
++						label = "MIBIB";
++						reg = <0x20000 0x20000>;
++						read-only;
++					};
++					SBL2@40000 {
++						label = "SBL2";
++						reg = <0x40000 0x20000>;
++						read-only;
++					};
++					SBL3@60000 {
++						label = "SBL3";
++						reg = <0x60000 0x30000>;
++						read-only;
++					};
++					DDRCONFIG@90000 {
++						label = "DDRCONFIG";
++						reg = <0x90000 0x10000>;
++						read-only;
++					};
++					SSD@a0000 {
++						label = "SSD";
++						reg = <0xa0000 0x10000>;
++						read-only;
++					};
++					TZ@b0000 {
++						label = "TZ";
++						reg = <0xb0000 0x30000>;
++						read-only;
++					};
++					RPM@e0000 {
++						label = "RPM";
++						reg = <0xe0000 0x20000>;
++						read-only;
++					};
++					fs-uboot@100000 {
++						label = "fs-uboot";
++						reg = <0x100000 0x70000>;
++						read-only;
++					};
++					uboot-env@170000 {
++						label = "uboot-env";
++						reg = <0x170000 0x40000>;
++						read-only;
++					};
++					radio@1b0000 {
++						label = "radio";
++						reg = <0x1b0000 0x40000>;
++						read-only;
++					};
++					os-image@1f0000 {
++						label = "os-image";
++						reg = <0x1f0000 0x200000>;
++					};
++					rootfs@3f0000 {
++						label = "rootfs";
++						reg = <0x3f0000 0x1b00000>;
++					};
++					defaultmac: default-mac@1ef0000 {
++						label = "default-mac";
++						reg = <0x1ef0000 0x00200>;
++						read-only;
++					};
++					pin@1ef0200 {
++						label = "pin";
++						reg = <0x1ef0200 0x00200>;
++						read-only;
++					};
++					product-info@1ef0400 {
++						label = "product-info";
++						reg = <0x1ef0400 0x0fc00>;
++						read-only;
++					};
++					partition-table@1f00000 {
++						label = "partition-table";
++						reg = <0x1f00000 0x10000>;
++						read-only;
++					};
++					soft-version@1f10000 {
++						label = "soft-version";
++						reg = <0x1f10000 0x10000>;
++						read-only;
++					};
++					support-list@1f20000 {
++						label = "support-list";
++						reg = <0x1f20000 0x10000>;
++						read-only;
++					};
++					profile@1f30000 {
++						label = "profile";
++						reg = <0x1f30000 0x10000>;
++						read-only;
++					};
++					default-config@1f40000 {
++						label = "default-config";
++						reg = <0x1f40000 0x10000>;
++						read-only;
++					};
++					user-config@1f50000 {
++						label = "user-config";
++						reg = <0x1f50000 0x40000>;
++						read-only;
++					};
++					qos-db@1f90000 {
++						label = "qos-db";
++						reg = <0x1f90000 0x40000>;
++						read-only;
++					};
++					usb-config@1fd0000 {
++						label = "usb-config";
++						reg = <0x1fd0000 0x10000>;
++						read-only;
++					};
++					log@1fe0000 {
++						label = "log";
++						reg = <0x1fe0000 0x20000>;
++						read-only;
++					};
++				};
++			};
++		};
++
++		phy@100f8800 {		/* USB3 port 1 HS phy */
++			status = "ok";
++		};
++
++		phy@100f8830 {		/* USB3 port 1 SS phy */
++			status = "ok";
++		};
++
++		phy@110f8800 {		/* USB3 port 0 HS phy */
++			status = "ok";
++		};
++
++		phy@110f8830 {		/* USB3 port 0 SS phy */
++			status = "ok";
++		};
++
++		usb30@0 {
++			status = "ok";
++		};
++
++		usb30@1 {
++			status = "ok";
++		};
++
++		pcie0: pci@1b500000 {
++			status = "ok";
++			phy-tx0-term-offset = <7>;
++		};
++
++		pcie1: pci@1b700000 {
++			status = "ok";
++			phy-tx0-term-offset = <7>;
++		};
++
++		mdio0: mdio {
++			compatible = "virtual,mdio-gpio";
++			#address-cells = <1>;
++			#size-cells = <0>;
++			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
++			pinctrl-0 = <&mdio0_pins>;
++			pinctrl-names = "default";
++
++			phy0: ethernet-phy@0 {
++				device_type = "ethernet-phy";
++				reg = <0>;
++				qca,ar8327-initvals = <
++					0x00004 0x7600000   /* PAD0_MODE */
++					0x00008 0x1000000   /* PAD5_MODE */
++					0x0000c 0x80        /* PAD6_MODE */
++					0x000e4 0xaa545     /* MAC_POWER_SEL */
++					0x000e0 0xc74164de  /* SGMII_CTRL */
++					0x0007c 0x4e        /* PORT0_STATUS */
++					0x00094 0x4e        /* PORT6_STATUS */
++					>;
++			};
++
++			phy4: ethernet-phy@4 {
++				device_type = "ethernet-phy";
++				reg = <4>;
++			};
++		};
++
++		gmac1: ethernet@37200000 {
++			status = "ok";
++			phy-mode = "rgmii";
++			qcom,id = <1>;
++
++			pinctrl-0 = <&rgmii2_pins>;
++			pinctrl-names = "default";
++
++			mtd-mac-address = <&defaultmac 0x8>;
++			mtd-mac-address-increment = <1>;
++
++			fixed-link {
++				speed = <1000>;
++				full-duplex;
++			};
++		};
++
++		gmac2: ethernet@37400000 {
++			status = "ok";
++			phy-mode = "sgmii";
++			qcom,id = <2>;
++
++			mtd-mac-address = <&defaultmac 0x8>;
++
++			fixed-link {
++				speed = <1000>;
++				full-duplex;
++			};
++		};
++	};
++
++	gpio-keys {
++		compatible = "gpio-keys";
++
++		wifi {
++			label = "wifi";
++			gpios = <&qcom_pinmux 49 1>;
++			linux,code = <KEY_WLAN>;
++		};
++
++		reset {
++			label = "reset";
++			gpios = <&qcom_pinmux 64 1>;
++			linux,code = <KEY_RESTART>;
++		};
++
++		wps {
++			label = "wps";
++			gpios = <&qcom_pinmux 65 1>;
++			linux,code = <KEY_WPS_BUTTON>;
++		};
++                ledgeneral {
++			label = "ledgeneral";
++			gpios = <&qcom_pinmux 16 1>;
++			linux,code = <KEY_DOLLAR>;
++		};
++	};
++
++	gpio-leds {
++		compatible = "gpio-leds";
++
++		lan {
++			label = "lan:blue";
++			gpios = <&qcom_pinmux 6 0>;
++		};
++                usb4 {
++			label = "usb_4:blue";
++			gpios = <&qcom_pinmux 7 0>;
++		};
++                usb2 {
++			label = "usb_2:blue";
++			gpios = <&qcom_pinmux 8 0>;
++		};
++                wps {
++			label = "wps:blue";
++			gpios = <&qcom_pinmux 9 0>;
++		};
++                wan_blue {
++			label = "wan:blue";
++			gpios = <&qcom_pinmux 33 1>;
++		};
++                status {
++			label = "status:blue";
++			gpios = <&qcom_pinmux 53 0>;
++			default-state = "on";
++		};
++                ledgnr {
++			label = "ledgnr:blue";
++			gpios = <&qcom_pinmux 66 0>;
++		};
++        };
++};
++
++&adm_dma {
++	status = "ok";
++};