ramips: add support for Youku YK1

Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617

6 files changed, 141 insertions, 2 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 5627c8c..1c18ded 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -268,6 +268,11 @@ zbt-wr8305rt)
 zte-q7)
 	set_wifi_led "$board:blue:status"
 	;;
+youku-yk1)
+	ucidef_set_led_default "power" "power" "$board:blue:power" "1"
+	set_wifi_led "$board:blue:air"
+	set_usb_led "$board:blue:usb"
+	;;
 esac
 
 board_config_flush
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 3821742..22809d1 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -84,7 +84,8 @@ ramips_setup_interfaces()
 	wsr-600|\
 	wt1520|\
 	y1|\
-	zbt-wg2626)
+	zbt-wg2626|\
+	youku-yk1)
 		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
 		ucidef_add_switch "switch0" "1" "1"
 		ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index a1bcb72..d6fdeb9 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -460,6 +460,9 @@ ramips_board_detect() {
 	*"ZBT-WR8305RT")
 		name="zbt-wr8305rt"
 		;;
+	*"YK1")
+		name="youku-yk1"
+		;;
 	*)
 		name="generic"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 0e8d619..0b9dd43 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -134,7 +134,8 @@ platform_check_image() {
 	zbt-wa05|\
 	zbt-wg2626|\
 	zbt-wr8305rt|\
-	zte-q7)
+	zte-q7|\
+	youku-yk1)
 		[ "$magic" != "27051956" ] && {
 			echo "Invalid image type."
 			return 1
diff --git a/target/linux/ramips/dts/YOUKU-YK1.dts b/target/linux/ramips/dts/YOUKU-YK1.dts
new file mode 100644
index 0000000..418351c
--- /dev/null
+++ b/target/linux/ramips/dts/YOUKU-YK1.dts
@@ -0,0 +1,127 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+	compatible = "YOUKU-YK1", "ralink,mt7620a-soc";
+	model = "YOUKU YK1";
+
+	palmbus@10000000 {
+
+		gpio0: gpio@600 {
+			status = "okay";
+		};
+
+		gpio1: gpio@638 {
+			status = "okay";
+		};
+
+		gpio2: gpio@660 {
+			status = "okay";
+		};
+
+		gpio3: gpio@688 {
+			status = "okay";
+		};
+
+		spi@b00 {
+			status = "okay";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "w25q256";
+				reg = <0 0>;
+				linux,modalias = "m25p80", "w25q256";
+				spi-max-frequency = <10000000>;
+
+				partition@0 {
+					label = "u-boot";
+					reg = <0x0 0x30000>;
+					read-only;
+				};
+
+				partition@30000 {
+					label = "u-boot-env";
+					reg = <0x30000 0x10000>;
+					read-only;
+				};
+
+				factory: partition@40000 {
+					label = "factory";
+					reg = <0x40000 0x10000>;
+					read-only;
+				};
+
+				partition@50000 {
+					label = "firmware";
+					reg = <0x50000 0x1fb0000>;
+				};
+			};
+		};
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			default {
+				ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "ephy", "wled", "nd_sd";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	ethernet@10100000 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ephy_pins>;
+		mtd-mac-address = <&factory 0x4>;
+		ralink,port-map = "llllw";
+	};
+
+	wmac@10180000 {
+		ralink,mtd-eeprom = <&factory 0>;
+	};
+
+	sdhci@b0130000 {
+		status = "okay";
+	};
+
+	ehci@101c0000 {
+		status = "okay";
+	};
+
+	ohci@101c1000 {
+		status = "okay";
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		wan {
+			label = "youku-yk1:blue:wan";
+			gpios = <&gpio2 4 1>;
+		};
+		air {
+			label = "youku-yk1:blue:air";
+			gpios = <&gpio3 0 1>;
+		};
+		usb {
+			label = "youku-yk1:blue:usb";
+			gpios = <&gpio1 11 1>;
+		};
+		power {
+			label = "youku-yk1:blue:power";
+			gpios = <&gpio1 5 1>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+		reset {
+			label = "reset";
+			gpios = <&gpio0 1 1>;
+			linux,code = <0x198>;
+		};
+	};
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 5e19c3f..5a2b98c 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -900,6 +900,7 @@ Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WR
 Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
 Image/Build/Profile/MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),miwifi-mini,MIWIFI-MINI)
 Image/Build/Profile/ZTE-Q7=$(call BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
+Image/Build/Profile/YOUKU-YK1=$(call BuildFirmware/Default16M/$(1),$(1),youku-yk1,YOUKU-YK1)
 Image/Build/Profile/ZBT-WA05=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
 Image/Build/Profile/ZBT-WR8305RT=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wr8305rt,ZBT-WR8305RT)
 Image/Build/Profile/ArcherC20i=$(call BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
@@ -939,6 +940,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/WT3020,$(1))
 	$(call Image/Build/Profile/MIWIFI-MINI,$(1))
 	$(call Image/Build/Profile/ZTE-Q7,$(1))
+	$(call Image/Build/Profile/YOUKU-YK1,$(1))
 	$(call Image/Build/Profile/ZBT-WA05,$(1))
 	$(call Image/Build/Profile/ZBT-WR8305RT,$(1))
 	$(call Image/Build/Profile/ArcherC20i,$(1))