orion: remove linux 3.18 support

Signed-off-by: Felix Fietkau <nbd@nbd.name>

5 files changed, 0 insertions, 890 deletions

diff --git a/target/linux/orion/config-3.18 b/target/linux/orion/config-3.18
deleted file mode 100644
index 4c816be..0000000
--- a/target/linux/orion/config-3.18
+++ /dev/null
@@ -1,187 +0,0 @@
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_ORION5X=y
-# CONFIG_ARCH_ORION5X_DT is not set
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-CONFIG_ARM_NR_BANKS=8
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_THUMB is not set
-# CONFIG_ARPD is not set
-CONFIG_ATAGS=y
-CONFIG_AUTO_ZRELADDR=y
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200"
-CONFIG_CMDLINE_FORCE=y
-CONFIG_COMMON_CLK=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_FEROCEON=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_FEROCEON=y
-CONFIG_CPU_FEROCEON_OLD_ID=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_TLB_FEROCEON=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRYPTO_DEV_MV_CESA=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_HW=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
-CONFIG_DEBUG_UART_8250_SHIFT=2
-# CONFIG_DEBUG_UART_8250_WORD is not set
-CONFIG_DEBUG_UART_PHYS=0xf1012000
-CONFIG_DEBUG_UART_VIRT=0xfe012000
-# CONFIG_DEBUG_USER is not set
-CONFIG_DNOTIFY=y
-CONFIG_FRAME_POINTER=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HZ_PERIODIC=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_WORK=y
-CONFIG_KTIME_SCALAR=y
-CONFIG_LEDS_GPIO=y
-# CONFIG_MACH_BIGDISK is not set
-# CONFIG_MACH_D2NET is not set
-# CONFIG_MACH_D2NET_DT is not set
-# CONFIG_MACH_DB88F5281 is not set
-# CONFIG_MACH_DNS323 is not set
-# CONFIG_MACH_DT2 is not set
-# CONFIG_MACH_EDMINI_V2_DT is not set
-# CONFIG_MACH_KUROBOX_PRO is not set
-# CONFIG_MACH_LINKSTATION_LSCHL is not set
-# CONFIG_MACH_LINKSTATION_LS_HGL is not set
-# CONFIG_MACH_LINKSTATION_MINI is not set
-# CONFIG_MACH_LINKSTATION_PRO is not set
-# CONFIG_MACH_MSS2 is not set
-# CONFIG_MACH_MSS2_DT is not set
-# CONFIG_MACH_MV2120 is not set
-# CONFIG_MACH_NET2BIG is not set
-# CONFIG_MACH_RD88F5181L_FXO is not set
-# CONFIG_MACH_RD88F5181L_GE is not set
-# CONFIG_MACH_RD88F5182 is not set
-# CONFIG_MACH_RD88F5182_DT is not set
-# CONFIG_MACH_RD88F6183AP_GE is not set
-# CONFIG_MACH_TERASTATION_PRO2 is not set
-# CONFIG_MACH_TS209 is not set
-# CONFIG_MACH_TS409 is not set
-# CONFIG_MACH_TS78XX is not set
-CONFIG_MACH_WN802T=y
-CONFIG_MACH_WNR854T=y
-CONFIG_MACH_WRT350N_V2=y
-CONFIG_MDIO_BOARDINFO=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MV643XX_ETH=y
-CONFIG_MVEBU_MBUS=y
-CONFIG_MVMDIO=y
-# CONFIG_MVNETA is not set
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NET_DSA=y
-CONFIG_NET_DSA_MV88E6131=y
-CONFIG_NET_DSA_MV88E6XXX=y
-CONFIG_NET_DSA_MV88E6XXX_NEED_PPU=y
-CONFIG_NET_DSA_TAG_DSA=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PCI=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PHYLIB=y
-CONFIG_PLAT_ORION=y
-CONFIG_PLAT_ORION_LEGACY=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_RCU_STALL_COMMON is not set
-CONFIG_SCHED_HRTICK=y
-# CONFIG_SCSI_DMA is not set
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_UID16=y
-CONFIG_UIDGID_CONVERTED=y
-CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h"
-CONFIG_USB_ARCH_HAS_XHCI=y
-CONFIG_USB_SUPPORT=y
-CONFIG_VECTORS_BASE=0xffff0000
-# CONFIG_VFP is not set
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/orion/patches-3.18/100-wrt350nv2_openwrt_partition_map.patch b/target/linux/orion/patches-3.18/100-wrt350nv2_openwrt_partition_map.patch
deleted file mode 100644
index 8b61406..0000000
--- a/target/linux/orion/patches-3.18/100-wrt350nv2_openwrt_partition_map.patch
+++ /dev/null
@@ -1,31 +0,0 @@
---- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
-+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
-@@ -134,11 +134,11 @@ static struct mtd_partition wrt350n_v2_n
-	{
-		.name		= "kernel",
-		.offset		= 0x00000000,
--		.size		= 0x00760000,
-+		.size		= 0x00140000,	// change to kernel mtd size here (1/3)
-	}, {
-		.name		= "rootfs",
--		.offset		= 0x001a0000,
--		.size		= 0x005c0000,
-+		.offset		= 0x00140000,	// change to kernel mtd size here (2/3)
-+		.size		= 0x00610000,	// adopt to kernel mtd size here (3/3) = 0x00750000 - <kernel mtd size>
-	}, {
-		.name		= "lang",
-		.offset		= 0x00760000,
-@@ -151,6 +151,14 @@ static struct mtd_partition wrt350n_v2_n
-		.name		= "u-boot",
-		.offset		= 0x007c0000,
-		.size		= 0x00040000,
-+	}, {
-+		.name		= "eRcOmM_do_not_touch",
-+		.offset		= 0x00750000,
-+		.size		= 0x00010000,	// erasesize
-+	}, {
-+		.name		= "image",	// for sysupgrade
-+		.offset		= 0x00000000,
-+		.size		= 0x00750000,
-	},
- };
diff --git a/target/linux/orion/patches-3.18/101-wnr854t_partition_map.patch b/target/linux/orion/patches-3.18/101-wnr854t_partition_map.patch
deleted file mode 100644
index 0839ca4..0000000
--- a/target/linux/orion/patches-3.18/101-wnr854t_partition_map.patch
+++ /dev/null
@@ -1,24 +0,0 @@
---- a/arch/arm/mach-orion5x/wnr854t-setup.c
-+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
-@@ -57,15 +57,19 @@ static struct mtd_partition wnr854t_nor_
-	{
-		.name		= "kernel",
-		.offset		= 0x00000000,
--		.size		= 0x00100000,
-+		.size		= 0x00140000,
-	}, {
-		.name		= "rootfs",
--		.offset		= 0x00100000,
--		.size		= 0x00660000,
-+		.offset		= 0x00140000,
-+		.size		= 0x00620000,
-	}, {
-		.name		= "uboot",
-		.offset		= 0x00760000,
-		.size		= 0x00040000,
-+	}, {
-+		.name		= "image",	// for sysupgrade
-+		.offset		= 0x00000000,
-+		.size		= 0x00760000,
-	},
- };
diff --git a/target/linux/orion/patches-3.18/200-dt2_board_support.patch b/target/linux/orion/patches-3.18/200-dt2_board_support.patch
deleted file mode 100644
index 3d2efff..0000000
--- a/target/linux/orion/patches-3.18/200-dt2_board_support.patch
+++ /dev/null
@@ -1,570 +0,0 @@
-Index: linux-3.18.43/arch/arm/mach-orion5x/Kconfig
-===================================================================
---- linux-3.18.43.orig/arch/arm/mach-orion5x/Kconfig
-+++ linux-3.18.43/arch/arm/mach-orion5x/Kconfig
-@@ -36,6 +36,13 @@ config MACH_RD88F5182_DT
- 	  Say 'Y' here if you want your kernel to support the Marvell
- 	  Orion-NAS (88F5182) RD2, Flattened Device Tree.
- 
-+config MACH_DT2
-+	bool "Freecom DataTank Gateway"
-+	select I2C_BOARDINFO
-+	help
-+	  Say 'Y' here if you want your kernel to support the
-+	  Freecom DataTank Gateway
-+
- config MACH_KUROBOX_PRO
- 	bool "KuroBox Pro"
- 	select I2C_BOARDINFO
-Index: linux-3.18.43/arch/arm/mach-orion5x/Makefile
-===================================================================
---- linux-3.18.43.orig/arch/arm/mach-orion5x/Makefile
-+++ linux-3.18.43/arch/arm/mach-orion5x/Makefile
-@@ -14,6 +14,7 @@ obj-$(CONFIG_MACH_TS78XX)	+= ts78xx-setu
- obj-$(CONFIG_MACH_MV2120)	+= mv2120-setup.o
- obj-$(CONFIG_MACH_NET2BIG)	+= net2big-setup.o
- obj-$(CONFIG_MACH_WNR854T)	+= wnr854t-setup.o
-+obj-$(CONFIG_MACH_DT2)		+= dt2-setup.o
- obj-$(CONFIG_MACH_RD88F5181L_GE)	+= rd88f5181l-ge-setup.o
- obj-$(CONFIG_MACH_RD88F5181L_FXO)	+= rd88f5181l-fxo-setup.o
- obj-$(CONFIG_MACH_RD88F6183AP_GE)	+= rd88f6183ap-ge-setup.o
-Index: linux-3.18.43/arch/arm/mach-orion5x/dt2-common.h
-===================================================================
---- /dev/null
-+++ linux-3.18.43/arch/arm/mach-orion5x/dt2-common.h
-@@ -0,0 +1,82 @@
-+#ifndef __INC_DT2_COMMON_H
-+#define __INC_DT2_COMMON_H
-+
-+#define ATAG_MV_UBOOT			0x41000403
-+
-+struct tag_mv_uboot {
-+	u32 uboot_version;
-+	u32 tclk;
-+	u32 sysclk;
-+	u32 isUsbHost;
-+	u32 overEthAddr;
-+	u8  dt2_eeprom[256];
-+};
-+
-+#define DT2_EEPROM_ADDR 		0x50
-+#define DT2_EEPROM_OFFSET		0
-+#define DT2_EEPROM_LENGTH		256
-+
-+#define DT2_SERIAL_NUMBER_DEFAULT	"run on default\0"
-+#define DT2_REVISION_DEFAULT_INIT 	0xFF
-+#define DT2_CONFIG_FLAGS_DEFAULT 	0x00
-+
-+#define _PACKED_	__attribute__((packed))
-+
-+struct DT2_EEPROM_SD_CONFIG {
-+	unsigned int	ram_1;
-+	unsigned int	ram_2;
-+	unsigned int	ram_3;
-+	unsigned int	ram_4;
-+	unsigned char	ram_5;
-+	unsigned char	ram_6;
-+	unsigned short	ram_7;
-+	unsigned int 	magic_id;
-+	} _PACKED_;		// 24 Bytes in total
-+
-+struct DT2_EEPROM_FC_CONFIG {
-+	unsigned char	rtc_sts_mask;
-+	unsigned char	rtc_sts_init;
-+	unsigned char	rtc_int_mask;
-+	unsigned char	rtc_int_init;
-+	unsigned char	rtc_atrim_init;
-+	unsigned char	rtc_dtrim_init;
-+	unsigned char	dummy1;
-+	unsigned char	dummy2;
-+	unsigned char	dt2_config_flags;	/* 0x80 to load rtc_values to RTC */
-+	unsigned char	dt2_revision;		/* upper nibble is HW, lower nibble is FW */
-+	unsigned char	dt2_serial_number[16];	/* Serial number of DT-2 */
-+	} _PACKED_;		// 26 Bytes in total
-+
-+#define CFG_LOAD_RTC_VALUES 	0x80
-+
-+struct DT2_EEPROM_GW_CONFIG {
-+	unsigned int	dummy1;
-+	unsigned int	dummy2;
-+	unsigned int	dummy3;
-+	unsigned char	dummy4;
-+	unsigned char	tos_video_val1;
-+	unsigned char	tos_video_val2;
-+	unsigned char	tos_voip_val;
-+	unsigned char	qos_igmp_cfg;
-+	unsigned char	num_of_ifs;
-+	unsigned short	vlan_ports_if[3];
-+	unsigned char	mac_addr[3][6];
-+	} _PACKED_;		// 42 Bytes in total
-+
-+#define _SIZE_OF_ALL_STRUCTS_ (sizeof(struct DT2_EEPROM_SD_CONFIG) + sizeof(struct DT2_EEPROM_FC_CONFIG) +  sizeof(struct DT2_EEPROM_GW_CONFIG))
-+
-+// MV = EEPROM - SD - FC - GW - CRC
-+struct DT2_EEPROM_MV_CONFIG {
-+	unsigned int reg_addr[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)];
-+	unsigned int reg_data[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)];
-+ 	} _PACKED_;
-+
-+struct DT2_EEPROM_STRUCT {
-+	struct DT2_EEPROM_MV_CONFIG mv;
-+	struct DT2_EEPROM_SD_CONFIG sd;
-+	struct DT2_EEPROM_FC_CONFIG fc;
-+	struct DT2_EEPROM_GW_CONFIG gw;
-+	unsigned int	crc;
-+	} _PACKED_;
-+
-+#endif
-Index: linux-3.18.43/arch/arm/mach-orion5x/dt2-setup.c
-===================================================================
---- /dev/null
-+++ linux-3.18.43/arch/arm/mach-orion5x/dt2-setup.c
-@@ -0,0 +1,448 @@
-+/*
-+ * arch/arm/mach-orion5x/dt2-setup.c
-+ *
-+ * Freecom DataTank Gateway Setup
-+ *
-+ * Copyright (C) 2009 Zintis Petersons <Zintis.Petersons@abcsolutions.lv>
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2.  This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/pci.h>
-+#include <linux/irq.h>
-+#include <linux/mtd/physmap.h>
-+#include <linux/mv643xx_eth.h>
-+#include <linux/ethtool.h>
-+#include <linux/if_ether.h>
-+#include <net/dsa.h>
-+#include <linux/ata_platform.h>
-+#include <linux/i2c.h>
-+#include <linux/reboot.h>
-+#include <linux/interrupt.h>
-+#include <asm/mach-types.h>
-+#include <asm/gpio.h>
-+#include <asm/mach/arch.h>
-+#include <asm/mach/pci.h>
-+#include <mach/orion5x.h>
-+#include "common.h"
-+#include "mpp.h"
-+
-+/*****************************************************************************
-+ * DT2 local
-+ ****************************************************************************/
-+#include <asm/setup.h>
-+#include "dt2-common.h"
-+
-+u32 mvUbootVer = 0;
-+u32 mvTclk = 166666667;
-+u32 mvSysclk = 200000000;
-+u32 mvIsUsbHost = 1;
-+u32 overEthAddr = 0;
-+u32 gBoardId = -1;
-+struct DT2_EEPROM_STRUCT dt2_eeprom;
-+
-+/*****************************************************************************
-+ * DT2 Info
-+ ****************************************************************************/
-+/*
-+ * PCI
-+ */
-+
-+#define DT2_PCI_SLOT0_OFFS	7
-+#define DT2_PCI_SLOT0_IRQ_A_PIN	3
-+#define DT2_PCI_SLOT0_IRQ_B_PIN	2
-+
-+#define DT2_PIN_GPIO_SYNC	25
-+#define DT2_PIN_GPIO_POWER	24
-+#define DT2_PIN_GPIO_UNPLUG1	23
-+#define DT2_PIN_GPIO_UNPLUG2	22
-+#define DT2_PIN_GPIO_RESET	4
-+
-+#define DT2_NOR_BOOT_BASE	0xf4000000
-+#define DT2_NOR_BOOT_SIZE	SZ_512K
-+
-+#define DT2_LEDS_BASE		0xfa000000
-+#define DT2_LEDS_SIZE		SZ_1K
-+
-+/*****************************************************************************
-+ * 512K NOR Flash on Device bus Boot CS
-+ ****************************************************************************/
-+
-+static struct mtd_partition dt2_partitions[] = {
-+	{
-+		.name	= "u-boot",
-+		.size	= 0x00080000,
-+		.offset	= 0,
-+	},
-+};
-+
-+static struct physmap_flash_data dt2_nor_flash_data = {
-+	.width		= 1,		/* 8 bit bus width */
-+	.parts		= dt2_partitions,
-+	.nr_parts	= ARRAY_SIZE(dt2_partitions)
-+};
-+
-+static struct resource dt2_nor_flash_resource = {
-+	.flags		= IORESOURCE_MEM,
-+	.start		= DT2_NOR_BOOT_BASE,
-+	.end		= DT2_NOR_BOOT_BASE + DT2_NOR_BOOT_SIZE - 1,
-+};
-+
-+static struct platform_device dt2_nor_flash = {
-+	.name		= "physmap-flash",
-+	.id		= 0,
-+	.dev		= {
-+		.platform_data	= &dt2_nor_flash_data,
-+	},
-+	.resource	= &dt2_nor_flash_resource,
-+	.num_resources	= 1,
-+};
-+
-+/*****************************************************************************
-+ * PCI
-+ ****************************************************************************/
-+
-+void __init dt2_pci_preinit(void)
-+{
-+	int pin, irq;
-+
-+	/*
-+	 * Configure PCI GPIO IRQ pins
-+	 */
-+	pin = DT2_PCI_SLOT0_IRQ_A_PIN;
-+	if (gpio_request(pin, "PCI IntA") == 0) {
-+		if (gpio_direction_input(pin) == 0) {
-+			irq = gpio_to_irq(pin);
-+			irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
-+			printk (KERN_INFO "PCI IntA IRQ: %d\n", irq);
-+		} else {
-+			printk(KERN_ERR "dt2_pci_preinit failed to "
-+					"irq_set_irq_type pin %d\n", pin);
-+			gpio_free(pin);
-+		}
-+	} else {
-+		printk(KERN_ERR "dt2_pci_preinit failed to request gpio %d\n", pin);
-+	}
-+
-+	pin = DT2_PCI_SLOT0_IRQ_B_PIN;
-+	if (gpio_request(pin, "PCI IntB") == 0) {
-+		if (gpio_direction_input(pin) == 0) {
-+			irq = gpio_to_irq(pin);
-+			irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
-+			printk (KERN_INFO "PCI IntB IRQ: %d\n", irq);
-+		} else {
-+			printk(KERN_ERR "dt2_pci_preinit failed to "
-+					"irq_set_irq_type pin %d\n", pin);
-+			gpio_free(pin);
-+		}
-+	} else {
-+		printk(KERN_ERR "dt2_pci_preinit failed to gpio_request %d\n", pin);
-+	}
-+}
-+
-+static int __init dt2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-+{
-+	int irq;
-+
-+	/*
-+	 * Check for devices with hard-wired IRQs.
-+	 */
-+	irq = orion5x_pci_map_irq(dev, slot, pin);
-+	if (irq != -1){
-+		printk(KERN_INFO "orion5x_pci_map_irq: %d\n", irq);
-+		return irq;
-+	}
-+
-+	/*
-+	 * PCI IRQs are connected via GPIOs
-+	 */
-+	switch (slot - DT2_PCI_SLOT0_OFFS) {
-+	case 0:
-+		if (pin == 1){
-+			irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_A_PIN);
-+			printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_A_PIN: %d\n", irq);
-+		}
-+		else {
-+			irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_B_PIN);
-+			printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_B_PIN: %d\n", irq);
-+		}
-+	default:
-+		irq = -1;
-+			printk(KERN_INFO "dt2_pci_map_irq IRQ: %d\n", irq);
-+	}
-+
-+	return irq;
-+}
-+
-+static struct hw_pci dt2_pci __initdata = {
-+	.nr_controllers	= 2,
-+	.preinit	= dt2_pci_preinit,
-+	.setup		= orion5x_pci_sys_setup,
-+	.scan		= orion5x_pci_sys_scan_bus,
-+	.map_irq	= dt2_pci_map_irq,
-+};
-+
-+static int __init dt2_pci_init(void)
-+{
-+	if (machine_is_dt2())
-+		pci_common_init(&dt2_pci);
-+
-+	return 0;
-+}
-+
-+subsys_initcall(dt2_pci_init);
-+
-+/*****************************************************************************
-+ * Ethernet
-+ ****************************************************************************/
-+
-+static struct mv643xx_eth_platform_data dt2_eth_data = {
-+	.phy_addr	= MV643XX_ETH_PHY_NONE,
-+	.speed		= SPEED_1000,
-+	.duplex		= DUPLEX_FULL,
-+};
-+
-+static struct dsa_chip_data dt2_switch_chip_data = {
-+	.port_names[0] = "wan",
-+	.port_names[1] = "lan1",
-+	.port_names[2] = "lan2",
-+	.port_names[3] = "cpu",
-+	.port_names[4] = "lan3",
-+	.port_names[5] = "lan4",
-+};
-+
-+static struct dsa_platform_data dt2_switch_plat_data = {
-+	.nr_chips	= 1,
-+	.chip		= &dt2_switch_chip_data,
-+};
-+
-+/*****************************************************************************
-+ * RTC ISL1208 on I2C bus
-+ ****************************************************************************/
-+static struct i2c_board_info __initdata dt2_i2c_rtc = {
-+	I2C_BOARD_INFO("isl1208", 0x6F),
-+};
-+
-+/*****************************************************************************
-+ * Sata
-+ ****************************************************************************/
-+static struct mv_sata_platform_data dt2_sata_data = {
-+	.n_ports	= 2,
-+};
-+
-+/*****************************************************************************
-+ * General Setup
-+ ****************************************************************************/
-+static unsigned int dt2_mpp_modes[] __initdata = {
-+	MPP0_GPIO,		// RTC interrupt
-+	MPP1_GPIO,		// 88e6131 interrupt
-+	MPP2_GPIO,		// PCI_intB
-+	MPP3_GPIO,		// PCI_intA
-+	MPP4_GPIO,		// reset button switch
-+	MPP5_GPIO,
-+	MPP6_GPIO,
-+	MPP7_GPIO,
-+	MPP8_GPIO,
-+	MPP9_GIGE,		/* GE_RXERR */
-+	MPP10_GPIO,		// usb
-+	MPP11_GPIO,		// usb
-+	MPP12_GIGE,		// GE_TXD[4]
-+	MPP13_GIGE,		// GE_TXD[5]
-+	MPP14_GIGE,		// GE_TXD[6]
-+	MPP15_GIGE,		// GE_TXD[7]
-+	MPP16_GIGE,		// GE_RXD[4]
-+	MPP17_GIGE,		// GE_RXD[5]
-+	MPP18_GIGE,		// GE_RXD[6]
-+	MPP19_GIGE,		// GE_RXD[7]
-+	0,
-+};
-+
-+/*****************************************************************************
-+ * LEDS
-+ ****************************************************************************/
-+static struct platform_device dt2_leds = {
-+	.name		= "dt2-led",
-+	.id		= -1,
-+};
-+
-+/****************************************************************************
-+ * GPIO key
-+ ****************************************************************************/
-+static irqreturn_t dt2_reset_handler(int irq, void *dev_id)
-+{
-+	/* This is the paper-clip reset which does an emergency reboot. */
-+	printk(KERN_INFO "Restarting system.\n");
-+	machine_restart(NULL);
-+
-+	/* This should never be reached. */
-+	return IRQ_HANDLED;
-+}
-+
-+static irqreturn_t dt2_power_handler(int irq, void *dev_id)
-+{
-+	printk(KERN_INFO "Shutting down system.\n");
-+	machine_power_off();
-+	return IRQ_HANDLED;
-+}
-+
-+static void __init dt2_init(void)
-+{
-+	/*
-+	 * Setup basic Orion functions. Need to be called early.
-+	 */
-+	orion5x_init();
-+
-+	orion5x_mpp_conf(dt2_mpp_modes);
-+
-+	/*
-+	 * Configure peripherals.
-+	 */
-+
-+	orion5x_uart0_init();
-+	orion5x_ehci0_init();
-+	orion5x_ehci1_init();
-+	orion5x_i2c_init();
-+	orion5x_sata_init(&dt2_sata_data);
-+	orion5x_xor_init();
-+
-+	printk(KERN_INFO "U-Boot parameters:\n");
-+	printk(KERN_INFO "Sys Clk = %d, Tclk = %d, BoardID = 0x%02x\n", mvSysclk, mvTclk, gBoardId);
-+
-+	printk(KERN_INFO "Serial: %s\n", dt2_eeprom.fc.dt2_serial_number);
-+	printk(KERN_INFO "Revision: %016x\n", dt2_eeprom.fc.dt2_revision);
-+	printk(KERN_INFO "DT2: Using MAC address %pM for port 0\n",
-+	       dt2_eeprom.gw.mac_addr[0]);
-+	printk(KERN_INFO "DT2: Using MAC address %pM for port 1\n",
-+	       dt2_eeprom.gw.mac_addr[1]);
-+
-+	orion5x_eth_init(&dt2_eth_data);
-+	memcpy(dt2_eth_data.mac_addr, dt2_eeprom.gw.mac_addr[0], 6);
-+	orion5x_eth_switch_init(&dt2_switch_plat_data, NO_IRQ);
-+
-+	i2c_register_board_info(0, &dt2_i2c_rtc, 1);
-+
-+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-+				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-+				    DT2_NOR_BOOT_BASE, DT2_NOR_BOOT_SIZE);
-+
-+	platform_device_register(&dt2_nor_flash);
-+
-+	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(0),
-+				    ORION_MBUS_DEVBUS_ATTR(0),
-+				    DT2_LEDS_BASE, DT2_LEDS_SIZE);
-+	platform_device_register(&dt2_leds);
-+
-+	if (request_irq(gpio_to_irq(DT2_PIN_GPIO_RESET), &dt2_reset_handler,
-+			IRQF_TRIGGER_LOW,
-+			"DT2: Reset button", NULL) < 0) {
-+
-+		printk("DT2: Reset Button IRQ %d not available\n",
-+			gpio_to_irq(DT2_PIN_GPIO_RESET));
-+	}
-+
-+	if (request_irq(gpio_to_irq(DT2_PIN_GPIO_POWER), &dt2_power_handler,
-+			IRQF_TRIGGER_LOW,
-+			"DT2: Power button", NULL) < 0) {
-+
-+		printk(KERN_DEBUG "DT2: Power Button IRQ %d not available\n",
-+			gpio_to_irq(DT2_PIN_GPIO_POWER));
-+	}
-+}
-+
-+static int __init parse_tag_dt2_uboot(const struct tag *t)
-+{
-+	struct tag_mv_uboot *mv_uboot;
-+
-+	// Get pointer to our block
-+	mv_uboot = (struct tag_mv_uboot*)&t->u;
-+	mvTclk = mv_uboot->tclk;
-+	mvSysclk = mv_uboot->sysclk;
-+	mvUbootVer = mv_uboot->uboot_version;
-+	mvIsUsbHost = mv_uboot->isUsbHost;
-+
-+	// Some clock fixups
-+	if(mvTclk == 166000000) mvTclk = 166666667;
-+	else if(mvTclk == 133000000) mvTclk = 133333333;
-+	else if(mvSysclk == 166000000) mvSysclk = 166666667;
-+
-+	gBoardId =  (mvUbootVer & 0xff);
-+
-+	//DT2 specific data
-+	memcpy(&dt2_eeprom, mv_uboot->dt2_eeprom, sizeof(struct DT2_EEPROM_STRUCT));
-+
-+	return 0;
-+}
-+__tagtable(ATAG_MV_UBOOT, parse_tag_dt2_uboot);
-+
-+/*
-+ * This is OpenWrt specific fixup. It includes code from original "tag_fixup_mem32" to
-+ * fixup bogus memory tags and also fixes kernel cmdline by adding " init=/etc/preinit"
-+ * at the end. It is important to flash OpenWrt image from original Freecom firmware.
-+ *
-+ * Vanilla kernel should use "tag_fixup_mem32" function.
-+ */
-+static void __init openwrt_fixup(struct tag *t, char **from)
-+{
-+	char *p = NULL;
-+	static char openwrt_init_tag[] __initdata = " init=/etc/preinit";
-+
-+	for (; t->hdr.size; t = tag_next(t)){
-+		/* Locate the Freecom cmdline */
-+		if (t->hdr.tag == ATAG_CMDLINE) {
-+			p = t->u.cmdline.cmdline;
-+			printk("%s(%d): Found cmdline '%s' at 0x%0lx\n",
-+			       __FUNCTION__, __LINE__, p, (unsigned long)p);
-+		}
-+		/*
-+		 * Many orion-based systems have buggy bootloader implementations.
-+		 * This is a common fixup for bogus memory tags.
-+		 */
-+		if (t->hdr.tag == ATAG_MEM &&
-+		    (!t->u.mem.size || t->u.mem.size & ~PAGE_MASK ||
-+		     t->u.mem.start & ~PAGE_MASK)) {
-+			printk(KERN_WARNING
-+			       "Clearing invalid memory bank %dKB@0x%08x\n",
-+			       t->u.mem.size / 1024, t->u.mem.start);
-+			t->hdr.tag = 0;
-+		}
-+	}
-+
-+	printk("%s(%d): End of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t);
-+
-+	/* Overwrite the end of the table with a new cmdline tag. */
-+	t->hdr.tag = ATAG_CMDLINE;
-+	t->hdr.size =
-+		(sizeof (struct tag_header) +
-+		 strlen(p) + strlen(openwrt_init_tag) + 1 + 4) >> 2;
-+
-+	strlcpy(t->u.cmdline.cmdline, p, COMMAND_LINE_SIZE);
-+	strlcpy(t->u.cmdline.cmdline + strlen(p), openwrt_init_tag,
-+		COMMAND_LINE_SIZE - strlen(p));
-+
-+	printk("%s(%d): New cmdline '%s' at 0x%0lx\n",
-+	       __FUNCTION__, __LINE__,
-+	       t->u.cmdline.cmdline, (unsigned long)t->u.cmdline.cmdline);
-+
-+	t = tag_next(t);
-+
-+	printk("%s(%d): New end of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t);
-+
-+	t->hdr.tag = ATAG_NONE;
-+	t->hdr.size = 0;
-+}
-+
-+/* Warning: Freecom uses their own custom bootloader with mach-type (=1500) */
-+MACHINE_START(DT2, "Freecom DataTank Gateway")
-+	/* Maintainer: Zintis Petersons <Zintis.Petersons@abcsolutions.lv> */
-+	.atag_offset    = 0x100,
-+	.init_machine	= dt2_init,
-+	.map_io		= orion5x_map_io,
-+	.init_irq	= orion5x_init_irq,
-+	.init_time	= orion5x_timer_init,
-+	.fixup		= openwrt_fixup, //tag_fixup_mem32,
-+MACHINE_END
diff --git a/target/linux/orion/patches-3.18/210-wn802t_support.patch b/target/linux/orion/patches-3.18/210-wn802t_support.patch
deleted file mode 100644
index e17d399..0000000
--- a/target/linux/orion/patches-3.18/210-wn802t_support.patch
+++ /dev/null
@@ -1,78 +0,0 @@
---- a/arch/arm/mach-orion5x/Kconfig
-+++ b/arch/arm/mach-orion5x/Kconfig
-@@ -144,10 +144,13 @@ config MACH_MSS2_DT
-	  Maxtor Shared Storage II platform.
-
- config MACH_WNR854T
--	bool "Netgear WNR854T"
-+	bool "Netgear WNR854T / WN802T"
-	help
-	  Say 'Y' here if you want your kernel to support the
--	  Netgear WNR854T platform.
-+	  Netgear WNR854T or WN802T platform.
-+
-+config MACH_WN802T
-+	def_bool MACH_WNR854T
-
- config MACH_RD88F5181L_GE
-	bool "Marvell Orion-VoIP GE Reference Design"
---- a/arch/arm/mach-orion5x/wnr854t-setup.c
-+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
-@@ -115,6 +115,15 @@ static struct dsa_platform_data wnr854t_
-	.chip		= &wnr854t_switch_chip_data,
- };
-
-+static struct dsa_chip_data wn802t_switch_chip_data = {
-+	.port_names[2] = "wan",
-+	.port_names[3] = "cpu",
-+};
-+
-+static struct dsa_platform_data wn802t_switch_plat_data = {
-+	.nr_chips	= 1,
-+	.chip		= &wn802t_switch_chip_data,
-+};
- static void __init wnr854t_init(void)
- {
-	/*
-@@ -128,7 +137,12 @@ static void __init wnr854t_init(void)
-	 * Configure peripherals.
-	 */
-	orion5x_eth_init(&wnr854t_eth_data);
--	orion5x_eth_switch_init(&wnr854t_switch_plat_data, NO_IRQ);
-+
-+	if (machine_is_wn802t())
-+		orion5x_eth_switch_init(&wn802t_switch_plat_data, NO_IRQ);
-+	else
-+		orion5x_eth_switch_init(&wnr854t_switch_plat_data, NO_IRQ);
-+
-	orion5x_uart0_init();
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-@@ -168,7 +182,7 @@ static struct hw_pci wnr854t_pci __initd
-
- static int __init wnr854t_pci_init(void)
- {
--	if (machine_is_wnr854t())
-+	if (machine_is_wnr854t() || machine_is_wn802t())
-		pci_common_init(&wnr854t_pci);
-
-	return 0;
-@@ -179,6 +193,18 @@ MACHINE_START(WNR854T, "Netgear WNR854T"
-	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
-	.atag_offset	= 0x100,
-	.init_machine	= wnr854t_init,
-+	.map_io		= orion5x_map_io,
-+	.init_early	= orion5x_init_early,
-+	.init_irq	= orion5x_init_irq,
-+	.init_time	= orion5x_timer_init,
-+	.fixup		= tag_fixup_mem32,
-+	.restart	= orion5x_restart,
-+MACHINE_END
-+
-+MACHINE_START(WN802T, "Netgear WN802T")
-+	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
-+	.atag_offset	= 0x100,
-+	.init_machine	= wnr854t_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,