ar71xx: add support for the D-Link DIR-825 rev. B1 board (thanks to ValXdater)

SVN-Revision: 18621

13 files changed, 397 insertions, 1 deletions

diff --git a/target/linux/ar71xx/base-files/etc/defconfig/dir825b1/network b/target/linux/ar71xx/base-files/etc/defconfig/dir825b1/network
new file mode 100644
index 0000000..2d4d8e0
--- /dev/null
+++ b/target/linux/ar71xx/base-files/etc/defconfig/dir825b1/network
@@ -0,0 +1,16 @@
+config interface loopback
+	option ifname	lo
+	option proto	static
+	option ipaddr	127.0.0.1
+	option netmask	255.0.0.0
+
+config interface lan
+	option ifname	eth0
+	option type	bridge
+	option proto	static
+	option ipaddr	192.168.1.1
+	option netmask	255.255.255.0
+
+config interface wan
+	option ifname	eth1
+	option proto	dhcp
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 1d88f43..c350f2c 100755
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -42,6 +42,9 @@ get_status_led() {
 	bullet-m | rocket-m | nano-m)
 		status_led="ubnt:green:link4"
 		;;
+	dir825b1)
+		status_led="dir825b1:orange:power"
+		;;
 	ls-sr71)
 		status_led="ubnt:green:d22"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index c24a8b3..ba4b0a2 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -19,6 +19,9 @@ ar71xx_board_name() {
 	*AW-NR580)
 		name="aw-nr580"
 		;;
+	*DIR825B1)
+		name="dir825b1"
+		;;
 	*"Bullet M")
 		name="bullet-m"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 97c3a41..90fa008 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -68,7 +68,7 @@ platform_check_image() {
 	[ "$ARGC" -gt 1 ] && return 1
 
 	case "$board" in
-	ap83 | mzk-w04nu | mzk-w300nh | tew-632brp | wrt-400n | bullet-m | nano-m | rocket-m)
+	ap83 | dir825b1 | mzk-w04nu | mzk-w300nh | tew-632brp | wrt-400n | bullet-m | nano-m | rocket-m)
 		[ "$magic" != "2705" ] && {
 			echo "Invalid image type."
 			return 1
diff --git a/target/linux/ar71xx/config-2.6.30 b/target/linux/ar71xx/config-2.6.30
index 4a2f129..07e2492 100644
--- a/target/linux/ar71xx/config-2.6.30
+++ b/target/linux/ar71xx/config-2.6.30
@@ -6,6 +6,7 @@ CONFIG_AG71XX=y
 CONFIG_AR71XX_MACH_AP81=y
 CONFIG_AR71XX_MACH_AP83=y
 CONFIG_AR71XX_MACH_AW_NR580=y
+CONFIG_AR71XX_MACH_DIR825B1=y
 CONFIG_AR71XX_MACH_GENERIC=y
 CONFIG_AR71XX_MACH_MZK_W04NU=y
 CONFIG_AR71XX_MACH_MZK_W300NH=y
diff --git a/target/linux/ar71xx/config-2.6.31 b/target/linux/ar71xx/config-2.6.31
index b92b0f6..554b002 100644
--- a/target/linux/ar71xx/config-2.6.31
+++ b/target/linux/ar71xx/config-2.6.31
@@ -7,6 +7,7 @@ CONFIG_AG71XX=y
 CONFIG_AR71XX_MACH_AP81=y
 CONFIG_AR71XX_MACH_AP83=y
 CONFIG_AR71XX_MACH_AW_NR580=y
+CONFIG_AR71XX_MACH_DIR825B1=y
 CONFIG_AR71XX_MACH_GENERIC=y
 CONFIG_AR71XX_MACH_MZK_W04NU=y
 CONFIG_AR71XX_MACH_MZK_W300NH=y
diff --git a/target/linux/ar71xx/files/arch/mips/ar71xx/Kconfig b/target/linux/ar71xx/files/arch/mips/ar71xx/Kconfig
index 72c28b4..37a0e01 100644
--- a/target/linux/ar71xx/files/arch/mips/ar71xx/Kconfig
+++ b/target/linux/ar71xx/files/arch/mips/ar71xx/Kconfig
@@ -10,6 +10,10 @@ config AR71XX_MACH_AP83
 	bool "Atheros AP83 board support"
 	default y
 
+config AR71XX_MACH_DIR825B1
+	bool "D-Link DIR-825 rev. B1 board support"
+	default y
+
 config AR71XX_MACH_PB42
 	bool "Atheros PB42 board support"
 	default y
diff --git a/target/linux/ar71xx/files/arch/mips/ar71xx/Makefile b/target/linux/ar71xx/files/arch/mips/ar71xx/Makefile
index 71ba835..d77438f 100644
--- a/target/linux/ar71xx/files/arch/mips/ar71xx/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ar71xx/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_PCI)			+= pci.o
 obj-$(CONFIG_AR71XX_MACH_AP81)		+= mach-ap81.o
 obj-$(CONFIG_AR71XX_MACH_AP83)		+= mach-ap83.o
 obj-$(CONFIG_AR71XX_MACH_AW_NR580)	+= mach-aw-nr580.o
+obj-$(CONFIG_AR71XX_MACH_DIR825B1)	+= mach-dir825b1.o
 obj-$(CONFIG_AR71XX_MACH_GENERIC)	+= mach-generic.o
 obj-$(CONFIG_AR71XX_MACH_MZK_W04NU)	+= mach-mzk-w04nu.o
 obj-$(CONFIG_AR71XX_MACH_MZK_W300NH)	+= mach-mzk-w300nh.o
diff --git a/target/linux/ar71xx/files/arch/mips/ar71xx/mach-dir825b1.c b/target/linux/ar71xx/files/arch/mips/ar71xx/mach-dir825b1.c
new file mode 100644
index 0000000..dbf244c
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ar71xx/mach-dir825b1.c
@@ -0,0 +1,317 @@
+/*
+ *  D-Link DIR-825 rev. B1 board support
+ *
+ *  Copyright (C) 2009 Lukas Kuna, Evkanet, s.r.o.
+ *
+ *  based on mach-wndr3700.c
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/input.h>
+
+#include <asm/mips_machine.h>
+#include <asm/mach-ar71xx/ar71xx.h>
+#include <asm/mach-ar71xx/pci.h>
+
+#include <linux/pci.h>
+#include <linux/ath9k_platform.h>
+#include <linux/delay.h>
+
+#include "devices.h"
+
+
+#define DIR825B1_GPIO_LED_BLUE_USB		0
+#define DIR825B1_GPIO_LED_ORANGE_POWER		1
+#define DIR825B1_GPIO_LED_BLUE_POWER		2
+#define DIR825B1_GPIO_LED_BLUE_POWERSAVE	4
+#define DIR825B1_GPIO_LED_ORANGE_PLANET		6
+#define DIR825B1_GPIO_LED_BLUE_PLANET		11
+
+#define DIR825B1_GPIO_BTN_RESET			3
+#define DIR825B1_GPIO_BTN_POWERSAVE		8
+
+#define DIR825B1_BUTTONS_POLL_INTERVAL		20
+
+
+#define DIR825B1_CAL_LOCATION_0			0xbf661000
+#define DIR825B1_CAL_LOCATION_1			0xbf665000
+
+#define DIR825B1_MAC_LOCATION_0			0x2ffa81b8
+#define DIR825B1_MAC_LOCATION_1			0x2ffa8370
+
+
+static struct ath9k_platform_data dir825b1_wmac0_data;
+static struct ath9k_platform_data dir825b1_wmac1_data;
+static char dir825b1_wmac0_mac[6];
+static char dir825b1_wmac1_mac[6];
+
+
+#ifdef CONFIG_MTD_PARTITIONS
+static struct mtd_partition dir825b1_partitions[] = {
+	{
+		.name		= "uboot",
+		.offset		= 0,
+		.size		= 0x040000,
+		.mask_flags	= MTD_WRITEABLE,
+	} , {
+		.name		= "config",
+		.offset		= 0x040000,
+		.size		= 0x010000,
+		.mask_flags	= MTD_WRITEABLE,
+	} , {
+		.name		= "firmware",
+		.offset		= 0x050000,
+		.size		= 0x610000,
+	} , {
+		.name		= "caldata",
+		.offset		= 0x660000,
+		.size		= 0x010000,
+		.mask_flags	= MTD_WRITEABLE,
+	}
+};
+#endif /* CONFIG_MTD_PARTITIONS */
+
+
+static struct flash_platform_data dir825b1_flash_data = {
+#ifdef CONFIG_MTD_PARTITIONS
+        .parts          = dir825b1_partitions,
+        .nr_parts       = ARRAY_SIZE(dir825b1_partitions),
+#endif
+};
+
+
+static struct spi_board_info dir825b1_spi_info[] = {
+	{
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.max_speed_hz	= 25000000,
+		.modalias	= "m25p80",
+		.platform_data  = &dir825b1_flash_data,
+	}
+};
+
+
+static struct gpio_led dir825b1_leds_gpio[] __initdata = {
+	{
+		.name		= "dir825b1:blue:usb",
+		.gpio		= DIR825B1_GPIO_LED_BLUE_USB,
+		.active_low	= 1,
+	}, {
+		.name		= "dir825b1:orange:power",
+		.gpio		= DIR825B1_GPIO_LED_ORANGE_POWER,
+		.active_low	= 1,
+	}, {
+		.name		= "dir825b1:blue:power",
+		.gpio		= DIR825B1_GPIO_LED_BLUE_POWER,
+		.active_low	= 1,
+	}, {
+		.name		= "dir825b1:blue:powersave",
+		.gpio		= DIR825B1_GPIO_LED_BLUE_POWERSAVE,
+		.active_low	= 1,
+	}, {
+		.name		= "dir825b1:orange:planet",
+		.gpio		= DIR825B1_GPIO_LED_ORANGE_PLANET,
+		.active_low	= 1,
+	}, {
+		.name		= "dir825b1:blue:planet",
+		.gpio		= DIR825B1_GPIO_LED_BLUE_PLANET,
+		.active_low	= 1,
+	}
+};
+
+
+static struct gpio_button dir825b1_gpio_buttons[] __initdata = {
+	{
+		.desc		= "reset",
+		.type		= EV_KEY,
+		.code		= BTN_0,
+		.threshold	= 5,
+		.gpio		= DIR825B1_GPIO_BTN_RESET,
+		.active_low	= 1,
+	} , {
+		.desc		= "powersave",
+		.type		= EV_KEY,
+		.code		= BTN_1,
+		.threshold	= 5,
+		.gpio		= DIR825B1_GPIO_BTN_POWERSAVE,
+		.active_low	= 1,
+	}
+};
+
+
+#ifdef CONFIG_PCI
+static struct ar71xx_pci_irq dir825b1_pci_irqs[] __initdata = {
+        {
+                .slot   = 0,
+                .pin    = 1,
+                .irq    = AR71XX_PCI_IRQ_DEV0,
+        }, {
+                .slot   = 1,
+                .pin    = 1,
+                .irq    = AR71XX_PCI_IRQ_DEV1,
+        }
+};
+
+
+static int dir825b1_pci_plat_dev_init(struct pci_dev *dev)
+{
+	switch(PCI_SLOT(dev->devfn))
+	{
+		case 17:
+			dev->dev.platform_data = &dir825b1_wmac0_data;
+			break;
+
+		case 18:
+			dev->dev.platform_data = &dir825b1_wmac1_data;
+			break;
+	}
+
+	return(0);
+}
+
+
+static void dir825b1_pci_fixup(struct pci_dev *dev)
+{
+	void __iomem *mem;
+	u16 *cal_data;
+	u16 cmd;
+	u32 bar0;
+	u32 val;
+
+	if (ar71xx_mach != AR71XX_MACH_DIR825B1) return;
+
+	dir825b1_pci_plat_dev_init(dev);
+	cal_data = dev->dev.platform_data;
+
+	if (*cal_data != 0xa55a)
+	{
+		printk(KERN_ERR "PCI: no calibration data found for %s\n",
+		       pci_name(dev));
+		return;
+	}
+
+	mem = ioremap(AR71XX_PCI_MEM_BASE, 0x10000);
+	if (!mem)
+	{
+		printk(KERN_ERR "PCI: ioremap error for device %s\n",
+		       pci_name(dev));
+		return;
+	}
+
+	printk(KERN_INFO "PCI: fixup device %s\n", pci_name(dev));
+
+	pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0);
+
+	/* Setup the PCI device to allow access to the internal registers */
+	pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, AR71XX_PCI_MEM_BASE);
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+	pci_write_config_word(dev, PCI_COMMAND, cmd);
+
+	/* set pointer to first reg address */
+	cal_data += 3;
+	while (*cal_data != 0xffff)
+	{
+		u32 reg;
+		reg = *cal_data++;
+		val = *cal_data++;
+		val |= (*cal_data++) << 16; 
+
+		__raw_writel(val, mem + reg);
+		udelay(100);
+	}
+
+	pci_read_config_dword(dev, PCI_VENDOR_ID, &val);
+	dev->vendor = val & 0xffff;
+	dev->device = (val >> 16) & 0xffff;
+
+	pci_read_config_dword(dev, PCI_CLASS_REVISION, &val);
+	dev->revision = val & 0xff;
+	dev->class = val >> 8; /* upper 3 bytes */
+
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	cmd &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
+	pci_write_config_word(dev, PCI_COMMAND, cmd);
+
+	pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, bar0);
+
+	iounmap(mem);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID,
+			dir825b1_pci_fixup);
+
+
+static void __init dir825b1_pci_init(void) 
+{
+	memcpy(dir825b1_wmac0_data.eeprom_data,
+	       (u8 *) KSEG1ADDR(DIR825B1_CAL_LOCATION_0),
+	       sizeof(dir825b1_wmac0_data.eeprom_data));
+
+	memcpy(dir825b1_wmac1_data.eeprom_data,
+	       (u8 *) KSEG1ADDR(DIR825B1_CAL_LOCATION_1),
+	       sizeof(dir825b1_wmac1_data.eeprom_data));
+
+	memcpy(dir825b1_wmac0_mac, (u8 *)KSEG1ADDR(DIR825B1_MAC_LOCATION_0), 6);
+	dir825b1_wmac0_data.macaddr = dir825b1_wmac0_mac;
+	memcpy(dir825b1_wmac1_mac, (u8 *)KSEG1ADDR(DIR825B1_MAC_LOCATION_1), 6);
+	dir825b1_wmac1_data.macaddr = dir825b1_wmac1_mac;
+
+	ar71xx_pci_plat_dev_init = dir825b1_pci_plat_dev_init;
+	ar71xx_pci_init(ARRAY_SIZE(dir825b1_pci_irqs), dir825b1_pci_irqs);
+}
+#else
+static void __init dir825b1_pci_init(void) { }
+#endif /* CONFIG_PCI */
+
+
+static void __init dir825b1_setup(void)
+{
+        u8 mac[6], i;
+
+	memcpy(mac, (u8*)KSEG1ADDR(DIR825B1_MAC_LOCATION_1), 6);
+	for(i = 5; i >= 3; i--)
+		if(++mac[i] != 0x00) break;
+
+	ar71xx_set_mac_base(mac);
+
+	ar71xx_add_device_mdio(0x0);
+
+	ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+	ar71xx_eth0_data.phy_mask = 0x1E;
+	ar71xx_eth0_data.speed = SPEED_1000;
+	ar71xx_eth0_data.duplex = DUPLEX_FULL;
+	ar71xx_eth0_pll_data.pll_1000 = 0x11110000;
+
+	ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+	ar71xx_eth1_data.phy_mask = 0xC0;
+	ar71xx_eth1_data.speed = SPEED_1000;
+	ar71xx_eth1_data.duplex = DUPLEX_FULL;
+	ar71xx_eth1_pll_data.pll_1000 = 0x11110000;
+
+	ar71xx_add_device_eth(0);
+	ar71xx_add_device_eth(1);
+
+	ar71xx_add_device_spi(NULL, dir825b1_spi_info,
+			      ARRAY_SIZE(dir825b1_spi_info));
+
+	ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(dir825b1_leds_gpio),
+					dir825b1_leds_gpio);
+
+	ar71xx_add_device_gpio_buttons(-1, DIR825B1_BUTTONS_POLL_INTERVAL,
+					ARRAY_SIZE(dir825b1_gpio_buttons),
+					dir825b1_gpio_buttons);
+
+	ar71xx_add_device_usb();
+
+	dir825b1_pci_init();
+}
+
+MIPS_MACHINE(AR71XX_MACH_DIR825B1, "D-Link DIR825B1", dir825b1_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ar71xx/prom.c b/target/linux/ar71xx/files/arch/mips/ar71xx/prom.c
index 4cc9763..ec7eed8 100644
--- a/target/linux/ar71xx/files/arch/mips/ar71xx/prom.c
+++ b/target/linux/ar71xx/files/arch/mips/ar71xx/prom.c
@@ -59,6 +59,9 @@ static struct board_rec boards[] __initdata = {
 		.name		= "AW-NR580",
 		.mach_type	= AR71XX_MACH_AW_NR580,
 	}, {
+		.name		= "DIR825B1",
+		.mach_type	= AR71XX_MACH_DIR825B1,
+	}, {
 		.name		= "TEW-632BRP",
 		.mach_type	= AR71XX_MACH_TEW_632BRP,
 	}, {
diff --git a/target/linux/ar71xx/files/arch/mips/include/asm/mach-ar71xx/ar71xx.h b/target/linux/ar71xx/files/arch/mips/include/asm/mach-ar71xx/ar71xx.h
index 4662932..f26fc85 100644
--- a/target/linux/ar71xx/files/arch/mips/include/asm/mach-ar71xx/ar71xx.h
+++ b/target/linux/ar71xx/files/arch/mips/include/asm/mach-ar71xx/ar71xx.h
@@ -124,6 +124,7 @@ enum ar71xx_mach_type {
 	AR71XX_MACH_AP81,	/* Atheros AP81 */
 	AR71XX_MACH_AP83,	/* Atheros AP83 */
 	AR71XX_MACH_AW_NR580,	/* AzureWave AW-NR580 */
+	AR71XX_MACH_DIR825B1,	/* D-Link DIR-825 rev. B1 */
 	AR71XX_MACH_RB_411,	/* MikroTik RouterBOARD 411/411A/411AH */
 	AR71XX_MACH_RB_411U,	/* MikroTik RouterBOARD 411U */
 	AR71XX_MACH_RB_433,	/* MikroTik RouterBOARD 433/433AH */
diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile
index 653a8af..8a5dbe6 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -77,6 +77,23 @@ define Image/Build/WRT400N
 	fi; fi
 endef
 
+dir825b1_mtdlayout=mtdparts=spi0.0:256k(uboot)ro,64k(config)ro,1024k(kernel),5184k(rootfs),64k(caldata)ro,6208k@0x50000(firmware)
+define Image/Build/DIR825B1
+	$(call PatchKernelLzma,$(2),$(3) $(dir825b1_mtdlayout))
+	$(call MkImageLzma,$(KDIR)/vmlinux-$(2).bin.lzma,$(call imgname,$(1),$(2)).bin)
+	if [ `stat -c%s "$(call imgname,$(1),$(2)).bin"` -gt 1048576 ]; then \
+	        echo "Warning: $(KDIR)/vmlinux-$(2).bin.lzma is too big"; \
+		rm -f $(call imgname,$(1),$(2)).bin; \
+	else if [ `stat -c%s $(KDIR)/root.$(1)` -gt 5308416 ]; then \
+	        echo "Warning: $(KDIR)/root.$(1) is too big"; \
+		rm -f $(call imgname,$(1),$(2)).bin; \
+	else \
+		dd if=$(KDIR)/root.$(1) of=$(call imgname,$(1),$(2)).bin bs=1k seek=1024; \
+		cp $(call imgname,$(1),$(2)).bin $(call imgname,$(1),$(2))-backup-loader.bin; \
+		echo -n "01AP94-AR7161-RT-080619-00" >> $(call imgname,$(1),$(2))-backup-loader.bin; \
+	fi; fi
+endef
+
 cameo_mtdlayout=mtdparts=spi0.0:128k(u-boot)ro,64k(config)ro,896k(kernel),2880k(rootfs),64k(art)ro,3776k@0x30000(firmware)
 define Image/Build/Cameo
 	$(call PatchKernelLzma,$(2),$(3) $(cameo_mtdlayout))
@@ -268,6 +285,18 @@ define Image/Build/Template/WRT400N/jffs2-64k
 	$(call Image/Build/Template/WRT400N,jffs2-64k,$(1),$(2),$(3))
 endef
 
+define Image/Build/Template/DIR825B1
+	$(call Image/Build/DIR825B1,$(1),$(2),$(3),$(4))
+endef
+
+define Image/Build/Template/DIR825B1/squashfs
+	$(call Image/Build/Template/DIR825B1,squashfs,$(1),$(2),$(3))
+endef
+
+define Image/Build/Template/DIR825B1/jffs2-64k
+	$(call Image/Build/Template/DIR825B1,jffs2-64k,$(1),$(2),$(3))
+endef
+
 define Image/Build/Template/CyberTAN
 	$(call Image/Build/CyberTAN,$(1),$(2),$(3),$(4))
 endef
@@ -453,6 +482,10 @@ define Image/Build/Profile/WRT400N
 	$(call Image/Build/Template/WRT400N/$(1),wrt400n,board=WRT400N)
 endef
 
+define Image/Build/Profile/DIR825B1
+	$(call Image/Build/Template/DIR825B1/$(1),dir825b1,board=DIR825B1)
+endef
+
 define Image/Build/Profile/WRT160NL
 	$(call Image/Build/Template/CyberTAN/$(1),wrt160nl,board=WRT160NL,1.00.01)
 endef
@@ -461,6 +494,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/AP83,$(1))
 	$(call Image/Build/Profile/A02RBW300N,$(1))
 	$(call Image/Build/Profile/DIR615C1,$(1))
+	$(call Image/Build/Profile/DIR825B1,$(1))
 	$(call Image/Build/Profile/MZKW04NU,$(1))
 	$(call Image/Build/Profile/MZKW300NH,$(1))
 	$(call Image/Build/Profile/TEW632BRP,$(1))
diff --git a/target/linux/ar71xx/profiles/d-link.mk b/target/linux/ar71xx/profiles/d-link.mk
index 460900d..3028a49 100644
--- a/target/linux/ar71xx/profiles/d-link.mk
+++ b/target/linux/ar71xx/profiles/d-link.mk
@@ -15,3 +15,15 @@ define Profile/DIR615C1/Description
 endef
 
 $(eval $(call Profile,DIR615C1))
+
+
+define Profile/DIR825B1
+	NAME:=D-Link DIR-825 rev. B1
+	PACKAGES:=kmod-ath9k hostapd-mini
+endef
+
+define Profile/DIR825B1/Description
+	Package set optimized for the D-Link DIR-825 rev. B1.
+endef
+
+$(eval $(call Profile,DIR825B1))