diff options
| -rwxr-xr-x | target/linux/ath79/base-files/etc/board.d/02_network | 5 | ||||
| -rw-r--r-- | target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom | 18 | ||||
| -rw-r--r-- | target/linux/ath79/config-4.14 | 1 | ||||
| -rw-r--r-- | target/linux/ath79/dts/ar7161_buffalo_wzr-hp-ag300h.dts | 284 | ||||
| -rw-r--r-- | target/linux/ath79/image/common-buffalo.mk | 20 | ||||
| -rw-r--r-- | target/linux/ath79/image/generic.mk | 14 | ||||
| -rw-r--r-- | target/linux/ath79/image/tiny.mk | 21 |
7 files changed, 336 insertions, 27 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 6cd794e..54fbe7b 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -27,6 +27,11 @@ ath79_setup_interfaces() wd,mynet-wifi-rangeextender) ucidef_set_interface_lan "eth0" ;; + buffalo,wzr-hp-ag300h) + ucidef_set_interface_wan "eth1" + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" + ;; buffalo,wzr-hp-g450h) ucidef_add_switch "switch0" \ "0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan" diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 8c10cb8..334e705 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -156,15 +156,16 @@ case "$FIRMWARE" in ;; "ath9k-eeprom-pci-0000:00:11.0.bin") case $board in - dlink,dir-825-b1) - ath9k_eeprom_extract "caldata" 4096 3768 - ath9k_patch_fw_mac_crc $(mtd_get_mac_text "caldata" 65440) 524 - ;; + buffalo,wzr-hp-ag300h|\ netgear,wndr3700|\ netgear,wndr3700v2|\ netgear,wndr3800) ath9k_eeprom_extract "art" 4096 3768 ;; + dlink,dir-825-b1) + ath9k_eeprom_extract "caldata" 4096 3768 + ath9k_patch_fw_mac_crc $(mtd_get_mac_text "caldata" 65440) 524 + ;; *) ath9k_eeprom_die "board $board is not supported yet" ;; @@ -172,15 +173,16 @@ case "$FIRMWARE" in ;; "ath9k-eeprom-pci-0000:00:12.0.bin") case $board in - dlink,dir-825-b1) - ath9k_eeprom_extract "caldata" 20480 3768 - ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 65460) 1) 524 - ;; + buffalo,wzr-hp-ag300h|\ netgear,wndr3700|\ netgear,wndr3700v2|\ netgear,wndr3800) ath9k_eeprom_extract "art" 20480 3768 ;; + dlink,dir-825-b1) + ath9k_eeprom_extract "caldata" 20480 3768 + ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_text "caldata" 65460) 1) 524 + ;; *) ath9k_eeprom_die "board $board is not supported yet" ;; diff --git a/target/linux/ath79/config-4.14 b/target/linux/ath79/config-4.14 index 6f273e1..f0365e9 100644 --- a/target/linux/ath79/config-4.14 +++ b/target/linux/ath79/config-4.14 @@ -173,6 +173,7 @@ CONFIG_MTD_SPLIT_TPLINK_FW=y CONFIG_MTD_SPLIT_UIMAGE_FW=y CONFIG_MTD_SPLIT_WRGG_FW=y CONFIG_MTD_TPLINK_PARTS=y +CONFIG_MTD_VIRT_CONCAT=y CONFIG_NEED_DMA_MAP_STATE=y CONFIG_NEED_PER_CPU_KM=y CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y diff --git a/target/linux/ath79/dts/ar7161_buffalo_wzr-hp-ag300h.dts b/target/linux/ath79/dts/ar7161_buffalo_wzr-hp-ag300h.dts new file mode 100644 index 0000000..8a5571a --- /dev/null +++ b/target/linux/ath79/dts/ar7161_buffalo_wzr-hp-ag300h.dts @@ -0,0 +1,284 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +#include "ar7100.dtsi" + +/ { + compatible = "buffalo,wzr-hp-ag300h", "qca,ar7161"; + model = "Buffalo WZR-HP-AG300H/WZR-600DHP"; + + aliases { + led-boot = &diag; + led-failsafe = &diag; + led-upgrade = &diag; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + extosc: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-output-names = "ref"; + clock-frequency = <40000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + + diag: diag { + label = "buffalo:red:diag"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + ath9k-leds { + // those leds are indeed attached to the wifi chips + + compatible = "gpio-leds"; + band2g_a { + label = "buffalo:amber:band2g"; + gpios = <&ath9k0 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + usb { + label = "buffalo:green:usb"; + gpios = <&ath9k0 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + trigger-sources = <&usb_ochi_port>, <&usb_echi_port>; + linux,default-trigger = "usbport"; + }; + + band2g_g { + label = "buffalo:green:band2g"; + gpios = <&ath9k0 5 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "phy0tpt"; + }; + + band5g_g { + label = "buffalo:green:band5g"; + gpios = <&ath9k1 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "phy1tpt"; + }; + + router { + label = "buffalo:green:router"; + gpios = <&ath9k1 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + movie_engine { + label = "buffalo:blue:movie_engine"; + gpios = <&ath9k1 4 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + band5g_a { + label = "buffalo:amber:band5g"; + gpios = <&ath9k1 5 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + reset { + linux,code = <KEY_RESTART>; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + usb { + linux,code = <BTN_2>; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + aoss { + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + router_auto { + linux,code = <BTN_6>; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + router_off { + linux,code = <BTN_5>; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + movie_engine { + linux,code = <BTN_7>; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + gpio-export { + compatible = "gpio-export"; + + gpio_usb_power { + gpio-export,name = "buffalo:power:usb"; + gpio-export,output = <1>; + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + }; + }; + + flash { + compatible = "mtd-concat"; + + devices = <&flash0 &flash1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x0040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x0040000 0x0010000>; + read-only; + }; + + art: partition@50000 { + label = "art"; + reg = <0x0050000 0x0010000>; + read-only; + }; + + partition@60000 { + label = "firmware"; + reg = <0x0060000 0x1f90000>; + }; + + partition@1ff0000 { + label = "user_property"; + reg = <0x1ff0000 0x0010000>; + read-only; + }; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb1 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + usb_ochi_port: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&usb2 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + usb_echi_port: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&pcie0 { + status = "okay"; + + ath9k0: wifi@0,11 { + compatible = "pci168c,0029"; + reg = <0x8800 0 0 0 0>; + qca,no-eeprom; + #gpio-cells = <2>; + gpio-controller; + }; + + ath9k1: wifi@0,12 { + compatible = "pci168c,0029"; + reg = <0x9000 0 0 0 0>; + qca,no-eeprom; + #gpio-cells = <2>; + gpio-controller; + }; +}; + +&uart { + status = "okay"; +}; + +&pll { + clocks = <&extosc>; +}; + +&spi { + status = "okay"; + num-cs = <2>; + cs-gpios = <0>, <0>; + + flash0: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + m25p,fast-read; + }; + + flash1: flash@1 { + compatible = "jedec,spi-nor"; + reg = <1>; + spi-max-frequency = <104000000>; + m25p,fast-read; + }; +}; + +&mdio0 { + status = "okay"; + + phy4: ethernet-phy@4 { + reg = <4>; + phy-mode = "rgmii"; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&art 0x120c>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +ð1 { + status = "okay"; + + mtd-mac-address = <&art 0x520c>; + mtd-mac-address-increment = <1>; + + phy-handle = <&phy4>; +}; diff --git a/target/linux/ath79/image/common-buffalo.mk b/target/linux/ath79/image/common-buffalo.mk new file mode 100644 index 0000000..a756f84 --- /dev/null +++ b/target/linux/ath79/image/common-buffalo.mk @@ -0,0 +1,20 @@ +define Build/buffalo-tftp-header + ( \ + echo -n -e "# Airstation Public Fmt1" | dd bs=32 count=1 conv=sync; \ + dd if=$@; \ + ) > $@.new + mv $@.new $@ +endef + +define Build/buffalo-tag + $(eval product=$(word 1,$(1))) + $(STAGING_DIR_HOST)/bin/buffalo-tag \ + -c 0x80041000 -d 0x801e8000 -w 3 \ + -a ath -v 1.99 -m 1.01 -f 1 \ + -b $(product) -p $(product) \ + -r M_ -l mlang8 \ + -i $@ -o $@.new + mv $@.new $@ +endef + + diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index fc38c09..e968dcf 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1,3 +1,4 @@ +include ./common-buffalo.mk include ./common-netgear.mk DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION @@ -68,6 +69,19 @@ define Device/avm_fritz4020 endef TARGET_DEVICES += avm_fritz4020 +define Device/buffalo_wzr-hp-ag300h + ATH_SOC := ar7161 + DEVICE_TITLE := Buffalo WZR-HP-AG300H + IMAGE_SIZE := 32256k + IMAGES += factory.bin tftp.bin + IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) + IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-AG300H 1.99 | buffalo-tag WZR-HP-AG300H + IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header + DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader + SUPPORTED_DEVICES += wzr-hp-ag300h +endef +TARGET_DEVICES += buffalo_wzr-hp-ag300h + define Device/buffalo_wzr-hp-g450h ATH_SOC := ar7242 DEVICE_TITLE := Buffalo WZR-HP-G450H diff --git a/target/linux/ath79/image/tiny.mk b/target/linux/ath79/image/tiny.mk index 0047554..531a7f3 100644 --- a/target/linux/ath79/image/tiny.mk +++ b/target/linux/ath79/image/tiny.mk @@ -1,23 +1,6 @@ -DEVICE_VARS += ROOTFS_SIZE - -define Build/buffalo-tftp-header - ( \ - echo -n -e "# Airstation Public Fmt1" | dd bs=32 count=1 conv=sync; \ - dd if=$@; \ - ) > $@.new - mv $@.new $@ -endef +include ./common-buffalo.mk -define Build/buffalo-tag - $(eval product=$(word 1,$(1))) - $(STAGING_DIR_HOST)/bin/buffalo-tag \ - -c 0x80041000 -d 0x801e8000 -w 3 \ - -a ath -v 1.99 -m 1.01 -f 1 \ - -b $(product) -p $(product) \ - -r M_ -l mlang8 \ - -i $@ -o $@.new - mv $@.new $@ -endef +DEVICE_VARS += ROOTFS_SIZE define Device/buffalo_bhr-4grv2 ATH_SOC := qca9558 |