summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--target/linux/etrax/files-2.6.30/drivers/usb/host/hc-cris-dbg.h140
-rw-r--r--target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.c4958
-rw-r--r--target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.h332
3 files changed, 0 insertions, 5430 deletions
diff --git a/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-cris-dbg.h b/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-cris-dbg.h
index c3f34c2..6a3696f 100644
--- a/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-cris-dbg.h
+++ b/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-cris-dbg.h
@@ -140,143 +140,3 @@
s; \
})
-/* macros for debug output */
-
-#define hcd_dbg(hcd, fmt, args...) \
- dev_info(hcd->self.controller, fmt, ## args)
-#define hcd_err(hcd, fmt, args...) \
- dev_err(hcd->self.controller, fmt, ## args)
-#define hcd_info(hcd, fmt, args...) \
- dev_info(hcd->self.controller, fmt, ## args)
-#define hcd_warn(hcd, fmt, args...) \
- dev_warn(hcd->self.controller, fmt, ## args)
-
-/*
-#define devdrv_dbg(fmt, args...) \
- printk(KERN_INFO "usb_devdrv dbg: ");printk(fmt, ## args)
-*/
-#define devdrv_dbg(fmt, args...) {}
-
-#define devdrv_err(fmt, args...) \
- printk(KERN_ERR "usb_devdrv error: ");printk(fmt, ## args)
-#define devdrv_info(fmt, args...) \
- printk(KERN_INFO "usb_devdrv: ");printk(fmt, ## args)
-
-#define irq_dbg(fmt, args...) \
- printk(KERN_INFO "crisv10_irq dbg: ");printk(fmt, ## args)
-#define irq_err(fmt, args...) \
- printk(KERN_ERR "crisv10_irq error: ");printk(fmt, ## args)
-#define irq_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_irq warn: ");printk(fmt, ## args)
-#define irq_info(fmt, args...) \
- printk(KERN_INFO "crisv10_hcd: ");printk(fmt, ## args)
-
-/*
-#define rh_dbg(fmt, args...) \
- printk(KERN_DEBUG "crisv10_rh dbg: ");printk(fmt, ## args)
-*/
-#define rh_dbg(fmt, args...) {}
-
-#define rh_err(fmt, args...) \
- printk(KERN_ERR "crisv10_rh error: ");printk(fmt, ## args)
-#define rh_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_rh warning: ");printk(fmt, ## args)
-#define rh_info(fmt, args...) \
- printk(KERN_INFO "crisv10_rh: ");printk(fmt, ## args)
-
-/*
-#define tc_dbg(fmt, args...) \
- printk(KERN_INFO "crisv10_tc dbg: ");printk(fmt, ## args)
-*/
-#define tc_dbg(fmt, args...) {while(0){}}
-
-#define tc_err(fmt, args...) \
- printk(KERN_ERR "crisv10_tc error: ");printk(fmt, ## args)
-/*
-#define tc_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_tc warning: ");printk(fmt, ## args)
-*/
-#define tc_warn(fmt, args...) {while(0){}}
-
-#define tc_info(fmt, args...) \
- printk(KERN_INFO "crisv10_tc: ");printk(fmt, ## args)
-
-
-/* Debug print-outs for various traffic types */
-
-#define intr_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_intr warning: ");printk(fmt, ## args)
-/*
-#define intr_dbg(fmt, args...) \
- printk(KERN_DEBUG "crisv10_intr dbg: ");printk(fmt, ## args)
-*/
-#define intr_dbg(fmt, args...) {while(0){}}
-
-
-#define isoc_err(fmt, args...) \
- printk(KERN_ERR "crisv10_isoc error: ");printk(fmt, ## args)
-/*
-#define isoc_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_isoc warning: ");printk(fmt, ## args)
-*/
-#define isoc_warn(fmt, args...) {while(0){}}
-
-/*
-#define isoc_dbg(fmt, args...) \
- printk(KERN_INFO "crisv10_isoc dbg: ");printk(fmt, ## args)
-*/
-#define isoc_dbg(fmt, args...) {while(0){}}
-
-/*
-#define timer_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_timer warning: ");printk(fmt, ## args)
-*/
-#define timer_warn(fmt, args...) {while(0){}}
-
-/*
-#define timer_dbg(fmt, args...) \
- printk(KERN_INFO "crisv10_timer dbg: ");printk(fmt, ## args)
-*/
-#define timer_dbg(fmt, args...) {while(0){}}
-
-
-/* Debug printouts for events related to late finishing of URBs */
-/*
-#define late_dbg(fmt, args...) \
- printk(KERN_INFO "crisv10_late dbg: ");printk(fmt, ## args)
-*/
-#define late_dbg(fmt, args...) {while(0){}}
-
-#define late_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_late warning: ");printk(fmt, ## args)
-/*
-#define errno_dbg(fmt, args...) \
- printk(KERN_INFO "crisv10_errno dbg: ");printk(fmt, ## args)
-*/
-#define errno_dbg(fmt, args...) {while(0){}}
-
-
-#define dma_dbg(fmt, args...) \
- printk(KERN_INFO "crisv10_dma dbg: ");printk(fmt, ## args)
-#define dma_err(fmt, args...) \
- printk(KERN_ERR "crisv10_dma error: ");printk(fmt, ## args)
-#define dma_warn(fmt, args...) \
- printk(KERN_INFO "crisv10_dma warning: ");printk(fmt, ## args)
-#define dma_info(fmt, args...) \
- printk(KERN_INFO "crisv10_dma: ");printk(fmt, ## args)
-
-
-
-#define str_dir(pipe) \
- (usb_pipeout(pipe) ? "out" : "in")
-#define str_type(pipe) \
- ({ \
- char *s = "?"; \
- switch (usb_pipetype(pipe)) { \
- case PIPE_ISOCHRONOUS: s = "iso"; break; \
- case PIPE_INTERRUPT: s = "intr"; break; \
- case PIPE_CONTROL: s = "ctrl"; break; \
- case PIPE_BULK: s = "bulk"; break; \
- }; \
- s; \
- })
diff --git a/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.c b/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.c
index de06e89..817e19e 100644
--- a/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.c
+++ b/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.c
@@ -4957,4962 +4957,4 @@ static void __exit module_hcd_exit(void)
/* Module hooks */
module_init(module_hcd_init);
module_exit(module_hcd_exit);
-/*
- *
- * ETRAX 100LX USB Host Controller Driver
- *
- * Copyright (C) 2005 - 2008 Axis Communications AB
- *
- * Author: Konrad Eriksson <konrad.eriksson@axis.se>
- *
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/moduleparam.h>
-#include <linux/spinlock.h>
-#include <linux/usb.h>
-#include <linux/platform_device.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/arch/dma.h>
-#include <asm/arch/io_interface_mux.h>
-
-#include "../core/hcd.h"
-#include "../core/hub.h"
-#include "hc-crisv10.h"
-#include "hc-cris-dbg.h"
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* Host Controller settings */
-/***************************************************************************/
-/***************************************************************************/
-
-#define VERSION "1.00-openwrt_diff"
-#define COPYRIGHT "(c) 2005, 2006 Axis Communications AB"
-#define DESCRIPTION "ETRAX 100LX USB Host Controller"
-
-#define ETRAX_USB_HC_IRQ USB_HC_IRQ_NBR
-#define ETRAX_USB_RX_IRQ USB_DMA_RX_IRQ_NBR
-#define ETRAX_USB_TX_IRQ USB_DMA_TX_IRQ_NBR
-
-/* Number of physical ports in Etrax 100LX */
-#define USB_ROOT_HUB_PORTS 2
-
-const char hc_name[] = "hc-crisv10";
-const char product_desc[] = DESCRIPTION;
-
-/* The number of epids is, among other things, used for pre-allocating
- ctrl, bulk and isoc EP descriptors (one for each epid).
- Assumed to be > 1 when initiating the DMA lists. */
-#define NBR_OF_EPIDS 32
-
-/* Support interrupt traffic intervals up to 128 ms. */
-#define MAX_INTR_INTERVAL 128
-
-/* If periodic traffic (intr or isoc) is to be used, then one entry in the EP
- table must be "invalid". By this we mean that we shouldn't care about epid
- attentions for this epid, or at least handle them differently from epid
- attentions for "valid" epids. This define determines which one to use
- (don't change it). */
-#define INVALID_EPID 31
-/* A special epid for the bulk dummys. */
-#define DUMMY_EPID 30
-
-/* Module settings */
-
-MODULE_DESCRIPTION(DESCRIPTION);
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Konrad Eriksson <konrad.eriksson@axis.se>");
-
-
-/* Module parameters */
-
-/* 0 = No ports enabled
- 1 = Only port 1 enabled (on board ethernet on devboard)
- 2 = Only port 2 enabled (external connector on devboard)
- 3 = Both ports enabled
-*/
-static unsigned int ports = 3;
-module_param(ports, uint, S_IRUGO);
-MODULE_PARM_DESC(ports, "Bitmask indicating USB ports to use");
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* Shared global variables for this module */
-/***************************************************************************/
-/***************************************************************************/
-
-/* EP descriptor lists for non period transfers. Must be 32-bit aligned. */
-static volatile struct USB_EP_Desc TxBulkEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4)));
-
-static volatile struct USB_EP_Desc TxCtrlEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4)));
-
-/* EP descriptor lists for period transfers. Must be 32-bit aligned. */
-static volatile struct USB_EP_Desc TxIntrEPList[MAX_INTR_INTERVAL] __attribute__ ((aligned (4)));
-static volatile struct USB_SB_Desc TxIntrSB_zout __attribute__ ((aligned (4)));
-
-static volatile struct USB_EP_Desc TxIsocEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4)));
-static volatile struct USB_SB_Desc TxIsocSB_zout __attribute__ ((aligned (4)));
-
-static volatile struct USB_SB_Desc TxIsocSBList[NBR_OF_EPIDS] __attribute__ ((aligned (4)));
-
-/* After each enabled bulk EP IN we put two disabled EP descriptors with the eol flag set,
- causing the DMA to stop the DMA channel. The first of these two has the intr flag set, which
- gives us a dma8_sub0_descr interrupt. When we receive this, we advance the DMA one step in the
- EP list and then restart the bulk channel, thus forcing a switch between bulk EP descriptors
- in each frame. */
-static volatile struct USB_EP_Desc TxBulkDummyEPList[NBR_OF_EPIDS][2] __attribute__ ((aligned (4)));
-
-/* List of URB pointers, where each points to the active URB for a epid.
- For Bulk, Ctrl and Intr this means which URB that currently is added to
- DMA lists (Isoc URBs are all directly added to DMA lists). As soon as
- URB has completed is the queue examined and the first URB in queue is
- removed and moved to the activeUrbList while its state change to STARTED and
- its transfer(s) gets added to DMA list (exception Isoc where URBs enter
- state STARTED directly and added transfers added to DMA lists). */
-static struct urb *activeUrbList[NBR_OF_EPIDS];
-
-/* Additional software state info for each epid */
-static struct etrax_epid epid_state[NBR_OF_EPIDS];
-
-/* Timer handles for bulk traffic timer used to avoid DMA bug where DMA stops
- even if there is new data waiting to be processed */
-static struct timer_list bulk_start_timer = TIMER_INITIALIZER(NULL, 0, 0);
-static struct timer_list bulk_eot_timer = TIMER_INITIALIZER(NULL, 0, 0);
-
-/* We want the start timer to expire before the eot timer, because the former
- might start traffic, thus making it unnecessary for the latter to time
- out. */
-#define BULK_START_TIMER_INTERVAL (HZ/50) /* 20 ms */
-#define BULK_EOT_TIMER_INTERVAL (HZ/16) /* 60 ms */
-
-/* Delay before a URB completion happen when it's scheduled to be delayed */
-#define LATER_TIMER_DELAY (HZ/50) /* 20 ms */
-
-/* Simplifying macros for checking software state info of a epid */
-/* ----------------------------------------------------------------------- */
-#define epid_inuse(epid) epid_state[epid].inuse
-#define epid_out_traffic(epid) epid_state[epid].out_traffic
-#define epid_isoc(epid) (epid_state[epid].type == PIPE_ISOCHRONOUS ? 1 : 0)
-#define epid_intr(epid) (epid_state[epid].type == PIPE_INTERRUPT ? 1 : 0)
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* DEBUG FUNCTIONS */
-/***************************************************************************/
-/***************************************************************************/
-/* Note that these functions are always available in their "__" variants,
- for use in error situations. The "__" missing variants are controlled by
- the USB_DEBUG_DESC/USB_DEBUG_URB macros. */
-static void __dump_urb(struct urb* purb)
-{
- struct crisv10_urb_priv *urb_priv = purb->hcpriv;
- int urb_num = -1;
- if(urb_priv) {
- urb_num = urb_priv->urb_num;
- }
- printk("\nURB:0x%x[%d]\n", (unsigned int)purb, urb_num);
- printk("dev :0x%08lx\n", (unsigned long)purb->dev);
- printk("pipe :0x%08x\n", purb->pipe);
- printk("status :%d\n", purb->status);
- printk("transfer_flags :0x%08x\n", purb->transfer_flags);
- printk("transfer_buffer :0x%08lx\n", (unsigned long)purb->transfer_buffer);
- printk("transfer_buffer_length:%d\n", purb->transfer_buffer_length);
- printk("actual_length :%d\n", purb->actual_length);
- printk("setup_packet :0x%08lx\n", (unsigned long)purb->setup_packet);
- printk("start_frame :%d\n", purb->start_frame);
- printk("number_of_packets :%d\n", purb->number_of_packets);
- printk("interval :%d\n", purb->interval);
- printk("error_count :%d\n", purb->error_count);
- printk("context :0x%08lx\n", (unsigned long)purb->context);
- printk("complete :0x%08lx\n\n", (unsigned long)purb->complete);
-}
-
-static void __dump_in_desc(volatile struct USB_IN_Desc *in)
-{
- printk("\nUSB_IN_Desc at 0x%08lx\n", (unsigned long)in);
- printk(" sw_len : 0x%04x (%d)\n", in->sw_len, in->sw_len);
- printk(" command : 0x%04x\n", in->command);
- printk(" next : 0x%08lx\n", in->next);
- printk(" buf : 0x%08lx\n", in->buf);
- printk(" hw_len : 0x%04x (%d)\n", in->hw_len, in->hw_len);
- printk(" status : 0x%04x\n\n", in->status);
-}
-
-static void __dump_sb_desc(volatile struct USB_SB_Desc *sb)
-{
- char tt = (sb->command & 0x30) >> 4;
- char *tt_string;
-
- switch (tt) {
- case 0:
- tt_string = "zout";
- break;
- case 1:
- tt_string = "in";
- break;
- case 2:
- tt_string = "out";
- break;
- case 3:
- tt_string = "setup";
- break;
- default:
- tt_string = "unknown (weird)";
- }
-
- printk(" USB_SB_Desc at 0x%08lx ", (unsigned long)sb);
- printk(" command:0x%04x (", sb->command);
- printk("rem:%d ", (sb->command & 0x3f00) >> 8);
- printk("full:%d ", (sb->command & 0x40) >> 6);
- printk("tt:%d(%s) ", tt, tt_string);
- printk("intr:%d ", (sb->command & 0x8) >> 3);
- printk("eot:%d ", (sb->command & 0x2) >> 1);
- printk("eol:%d)", sb->command & 0x1);
- printk(" sw_len:0x%04x(%d)", sb->sw_len, sb->sw_len);
- printk(" next:0x%08lx", sb->next);
- printk(" buf:0x%08lx\n", sb->buf);
-}
-
-
-static void __dump_ep_desc(volatile struct USB_EP_Desc *ep)
-{
- printk("USB_EP_Desc at 0x%08lx ", (unsigned long)ep);
- printk(" command:0x%04x (", ep->command);
- printk("ep_id:%d ", (ep->command & 0x1f00) >> 8);
- printk("enable:%d ", (ep->command & 0x10) >> 4);
- printk("intr:%d ", (ep->command & 0x8) >> 3);
- printk("eof:%d ", (ep->command & 0x2) >> 1);
- printk("eol:%d)", ep->command & 0x1);
- printk(" hw_len:0x%04x(%d)", ep->hw_len, ep->hw_len);
- printk(" next:0x%08lx", ep->next);
- printk(" sub:0x%08lx\n", ep->sub);
-}
-
-static inline void __dump_ep_list(int pipe_type)
-{
- volatile struct USB_EP_Desc *ep;
- volatile struct USB_EP_Desc *first_ep;
- volatile struct USB_SB_Desc *sb;
-
- switch (pipe_type)
- {
- case PIPE_BULK:
- first_ep = &TxBulkEPList[0];
- break;
- case PIPE_CONTROL:
- first_ep = &TxCtrlEPList[0];
- break;
- case PIPE_INTERRUPT:
- first_ep = &TxIntrEPList[0];
- break;
- case PIPE_ISOCHRONOUS:
- first_ep = &TxIsocEPList[0];
- break;
- default:
- return;
- }
- ep = first_ep;
-
- printk("\n\nDumping EP list...\n\n");
-
- do {
- __dump_ep_desc(ep);
- /* Cannot phys_to_virt on 0 as it turns into 80000000, which is != 0. */
- sb = ep->sub ? phys_to_virt(ep->sub) : 0;
- while (sb) {
- __dump_sb_desc(sb);
- sb = sb->next ? phys_to_virt(sb->next) : 0;
- }
- ep = (volatile struct USB_EP_Desc *)(phys_to_virt(ep->next));
-
- } while (ep != first_ep);
-}
-
-static inline void __dump_ept_data(int epid)
-{
- unsigned long flags;
- __u32 r_usb_ept_data;
-
- if (epid < 0 || epid > 31) {
- printk("Cannot dump ept data for invalid epid %d\n", epid);
- return;
- }
-
- local_irq_save(flags);
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid);
- nop();
- r_usb_ept_data = *R_USB_EPT_DATA;
- local_irq_restore(flags);
-
- printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", r_usb_ept_data, epid);
- if (r_usb_ept_data == 0) {
- /* No need for more detailed printing. */
- return;
- }
- printk(" valid : %d\n", (r_usb_ept_data & 0x80000000) >> 31);
- printk(" hold : %d\n", (r_usb_ept_data & 0x40000000) >> 30);
- printk(" error_count_in : %d\n", (r_usb_ept_data & 0x30000000) >> 28);
- printk(" t_in : %d\n", (r_usb_ept_data & 0x08000000) >> 27);
- printk(" low_speed : %d\n", (r_usb_ept_data & 0x04000000) >> 26);
- printk(" port : %d\n", (r_usb_ept_data & 0x03000000) >> 24);
- printk(" error_code : %d\n", (r_usb_ept_data & 0x00c00000) >> 22);
- printk(" t_out : %d\n", (r_usb_ept_data & 0x00200000) >> 21);
- printk(" error_count_out : %d\n", (r_usb_ept_data & 0x00180000) >> 19);
- printk(" max_len : %d\n", (r_usb_ept_data & 0x0003f800) >> 11);
- printk(" ep : %d\n", (r_usb_ept_data & 0x00000780) >> 7);
- printk(" dev : %d\n", (r_usb_ept_data & 0x0000003f));
-}
-
-static inline void __dump_ept_data_iso(int epid)
-{
- unsigned long flags;
- __u32 ept_data;
-
- if (epid < 0 || epid > 31) {
- printk("Cannot dump ept data for invalid epid %d\n", epid);
- return;
- }
-
- local_irq_save(flags);
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid);
- nop();
- ept_data = *R_USB_EPT_DATA_ISO;
- local_irq_restore(flags);
-
- printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", ept_data, epid);
- if (ept_data == 0) {
- /* No need for more detailed printing. */
- return;
- }
- printk(" valid : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, valid,
- ept_data));
- printk(" port : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, port,
- ept_data));
- printk(" error_code : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code,
- ept_data));
- printk(" max_len : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, max_len,
- ept_data));
- printk(" ep : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, ep,
- ept_data));
- printk(" dev : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, dev,
- ept_data));
-}
-
-static inline void __dump_ept_data_list(void)
-{
- int i;
-
- printk("Dumping the whole R_USB_EPT_DATA list\n");
-
- for (i = 0; i < 32; i++) {
- __dump_ept_data(i);
- }
-}
-
-static void debug_epid(int epid) {
- int i;
-
- if(epid_isoc(epid)) {
- __dump_ept_data_iso(epid);
- } else {
- __dump_ept_data(epid);
- }
-
- printk("Bulk:\n");
- for(i = 0; i < 32; i++) {
- if(IO_EXTRACT(USB_EP_command, epid, TxBulkEPList[i].command) ==
- epid) {
- printk("%d: ", i); __dump_ep_desc(&(TxBulkEPList[i]));
- }
- }
-
- printk("Ctrl:\n");
- for(i = 0; i < 32; i++) {
- if(IO_EXTRACT(USB_EP_command, epid, TxCtrlEPList[i].command) ==
- epid) {
- printk("%d: ", i); __dump_ep_desc(&(TxCtrlEPList[i]));
- }
- }
-
- printk("Intr:\n");
- for(i = 0; i < MAX_INTR_INTERVAL; i++) {
- if(IO_EXTRACT(USB_EP_command, epid, TxIntrEPList[i].command) ==
- epid) {
- printk("%d: ", i); __dump_ep_desc(&(TxIntrEPList[i]));
- }
- }
-
- printk("Isoc:\n");
- for(i = 0; i < 32; i++) {
- if(IO_EXTRACT(USB_EP_command, epid, TxIsocEPList[i].command) ==
- epid) {
- printk("%d: ", i); __dump_ep_desc(&(TxIsocEPList[i]));
- }
- }
-
- __dump_ept_data_list();
- __dump_ep_list(PIPE_INTERRUPT);
- printk("\n\n");
-}
-
-
-
-char* hcd_status_to_str(__u8 bUsbStatus) {
- static char hcd_status_str[128];
- hcd_status_str[0] = '\0';
- if(bUsbStatus & IO_STATE(R_USB_STATUS, ourun, yes)) {
- strcat(hcd_status_str, "ourun ");
- }
- if(bUsbStatus & IO_STATE(R_USB_STATUS, perror, yes)) {
- strcat(hcd_status_str, "perror ");
- }
- if(bUsbStatus & IO_STATE(R_USB_STATUS, device_mode, yes)) {
- strcat(hcd_status_str, "device_mode ");
- }
- if(bUsbStatus & IO_STATE(R_USB_STATUS, host_mode, yes)) {
- strcat(hcd_status_str, "host_mode ");
- }
- if(bUsbStatus & IO_STATE(R_USB_STATUS, started, yes)) {
- strcat(hcd_status_str, "started ");
- }
- if(bUsbStatus & IO_STATE(R_USB_STATUS, running, yes)) {
- strcat(hcd_status_str, "running ");
- }
- return hcd_status_str;
-}
-
-
-char* sblist_to_str(struct USB_SB_Desc* sb_desc) {
- static char sblist_to_str_buff[128];
- char tmp[32], tmp2[32];
- sblist_to_str_buff[0] = '\0';
- while(sb_desc != NULL) {
- switch(IO_EXTRACT(USB_SB_command, tt, sb_desc->command)) {
- case 0: sprintf(tmp, "zout"); break;
- case 1: sprintf(tmp, "in"); break;
- case 2: sprintf(tmp, "out"); break;
- case 3: sprintf(tmp, "setup"); break;
- }
- sprintf(tmp2, "(%s %d)", tmp, sb_desc->sw_len);
- strcat(sblist_to_str_buff, tmp2);
- if(sb_desc->next != 0) {
- sb_desc = phys_to_virt(sb_desc->next);
- } else {
- sb_desc = NULL;
- }
- }
- return sblist_to_str_buff;
-}
-
-char* port_status_to_str(__u16 wPortStatus) {
- static char port_status_str[128];
- port_status_str[0] = '\0';
- if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes)) {
- strcat(port_status_str, "connected ");
- }
- if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) {
- strcat(port_status_str, "enabled ");
- }
- if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, suspended, yes)) {
- strcat(port_status_str, "suspended ");
- }
- if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, reset, yes)) {
- strcat(port_status_str, "reset ");
- }
- if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, speed, full)) {
- strcat(port_status_str, "full-speed ");
- } else {
- strcat(port_status_str, "low-speed ");
- }
- return port_status_str;
-}
-
-
-char* endpoint_to_str(struct usb_endpoint_descriptor *ed) {
- static char endpoint_to_str_buff[128];
- char tmp[32];
- int epnum = ed->bEndpointAddress & 0x0F;
- int dir = ed->bEndpointAddress & 0x80;
- int type = ed->bmAttributes & 0x03;
- endpoint_to_str_buff[0] = '\0';
- sprintf(endpoint_to_str_buff, "ep:%d ", epnum);
- switch(type) {
- case 0:
- sprintf(tmp, " ctrl");
- break;
- case 1:
- sprintf(tmp, " isoc");
- break;
- case 2:
- sprintf(tmp, " bulk");
- break;
- case 3:
- sprintf(tmp, " intr");
- break;
- }
- strcat(endpoint_to_str_buff, tmp);
- if(dir) {
- sprintf(tmp, " in");
- } else {
- sprintf(tmp, " out");
- }
- strcat(endpoint_to_str_buff, tmp);
-
- return endpoint_to_str_buff;
-}
-
-/* Debug helper functions for Transfer Controller */
-char* pipe_to_str(unsigned int pipe) {
- static char pipe_to_str_buff[128];
- char tmp[64];
- sprintf(pipe_to_str_buff, "dir:%s", str_dir(pipe));
- sprintf(tmp, " type:%s", str_type(pipe));
- strcat(pipe_to_str_buff, tmp);
-
- sprintf(tmp, " dev:%d", usb_pipedevice(pipe));
- strcat(pipe_to_str_buff, tmp);
- sprintf(tmp, " ep:%d", usb_pipeendpoint(pipe));
- strcat(pipe_to_str_buff, tmp);
- return pipe_to_str_buff;
-}
-
-
-#define USB_DEBUG_DESC 1
-
-#ifdef USB_DEBUG_DESC
-#define dump_in_desc(x) __dump_in_desc(x)
-#define dump_sb_desc(...) __dump_sb_desc(...)
-#define dump_ep_desc(x) __dump_ep_desc(x)
-#define dump_ept_data(x) __dump_ept_data(x)
-#else
-#define dump_in_desc(...) do {} while (0)
-#define dump_sb_desc(...) do {} while (0)
-#define dump_ep_desc(...) do {} while (0)
-#endif
-
-
-/* Uncomment this to enable massive function call trace
- #define USB_DEBUG_TRACE */
-
-#ifdef USB_DEBUG_TRACE
-#define DBFENTER (printk(": Entering: %s\n", __FUNCTION__))
-#define DBFEXIT (printk(": Exiting: %s\n", __FUNCTION__))
-#else
-#define DBFENTER do {} while (0)
-#define DBFEXIT do {} while (0)
-#endif
-
-#define CHECK_ALIGN(x) if (((__u32)(x)) & 0x00000003) \
-{panic("Alignment check (DWORD) failed at %s:%s:%d\n", __FILE__, __FUNCTION__, __LINE__);}
-
-/* Most helpful debugging aid */
-#define ASSERT(expr) ((void) ((expr) ? 0 : (err("assert failed at: %s %d",__FUNCTION__, __LINE__))))
-
-
-/***************************************************************************/
-/***************************************************************************/
-/* Forward declarations */
-/***************************************************************************/
-/***************************************************************************/
-void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg);
-void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg);
-void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg);
-void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg);
-
-void rh_port_status_change(__u16[]);
-int rh_clear_port_feature(__u8, __u16);
-int rh_set_port_feature(__u8, __u16);
-static void rh_disable_port(unsigned int port);
-
-static void check_finished_bulk_tx_epids(struct usb_hcd *hcd,
- int timer);
-
-static int tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb,
- int mem_flags);
-static void tc_free_epid(struct usb_host_endpoint *ep);
-static int tc_allocate_epid(void);
-static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status);
-static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb,
- int status);
-
-static int urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid,
- int mem_flags);
-static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb);
-
-static int crisv10_usb_check_bandwidth(struct usb_device *dev,struct urb *urb);
-static void crisv10_usb_claim_bandwidth(
- struct usb_device *dev, struct urb *urb, int bustime, int isoc);
-static void crisv10_usb_release_bandwidth(
- struct usb_hcd *hcd, int isoc, int bandwidth);
-
-static inline struct urb *urb_list_first(int epid);
-static inline void urb_list_add(struct urb *urb, int epid,
- int mem_flags);
-static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid);
-static inline void urb_list_del(struct urb *urb, int epid);
-static inline void urb_list_move_last(struct urb *urb, int epid);
-static inline struct urb *urb_list_next(struct urb *urb, int epid);
-
-int create_sb_for_urb(struct urb *urb, int mem_flags);
-int init_intr_urb(struct urb *urb, int mem_flags);
-
-static inline void etrax_epid_set(__u8 index, __u32 data);
-static inline void etrax_epid_clear_error(__u8 index);
-static inline void etrax_epid_set_toggle(__u8 index, __u8 dirout,
- __u8 toggle);
-static inline __u8 etrax_epid_get_toggle(__u8 index, __u8 dirout);
-static inline __u32 etrax_epid_get(__u8 index);
-
-/* We're accessing the same register position in Etrax so
- when we do full access the internal difference doesn't matter */
-#define etrax_epid_iso_set(index, data) etrax_epid_set(index, data)
-#define etrax_epid_iso_get(index) etrax_epid_get(index)
-
-
-static void tc_dma_process_isoc_urb(struct urb *urb);
-static void tc_dma_process_queue(int epid);
-static void tc_dma_unlink_intr_urb(struct urb *urb);
-static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc);
-static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc);
-
-static void tc_bulk_start_timer_func(unsigned long dummy);
-static void tc_bulk_eot_timer_func(unsigned long dummy);
-
-
-/*************************************************************/
-/*************************************************************/
-/* Host Controler Driver block */
-/*************************************************************/
-/*************************************************************/
-
-/* HCD operations */
-static irqreturn_t crisv10_hcd_top_irq(int irq, void*);
-static int crisv10_hcd_reset(struct usb_hcd *);
-static int crisv10_hcd_start(struct usb_hcd *);
-static void crisv10_hcd_stop(struct usb_hcd *);
-#ifdef CONFIG_PM
-static int crisv10_hcd_suspend(struct device *, u32, u32);
-static int crisv10_hcd_resume(struct device *, u32);
-#endif /* CONFIG_PM */
-static int crisv10_hcd_get_frame(struct usb_hcd *);
-
-static int tc_urb_enqueue(struct usb_hcd *, struct urb *, gfp_t mem_flags);
-static int tc_urb_dequeue(struct usb_hcd *, struct urb *, int);
-static void tc_endpoint_disable(struct usb_hcd *, struct usb_host_endpoint *ep);
-
-static int rh_status_data_request(struct usb_hcd *, char *);
-static int rh_control_request(struct usb_hcd *, u16, u16, u16, char*, u16);
-
-#ifdef CONFIG_PM
-static int crisv10_hcd_hub_suspend(struct usb_hcd *);
-static int crisv10_hcd_hub_resume(struct usb_hcd *);
-#endif /* CONFIG_PM */
-#ifdef CONFIG_USB_OTG
-static int crisv10_hcd_start_port_reset(struct usb_hcd *, unsigned);
-#endif /* CONFIG_USB_OTG */
-
-/* host controller driver interface */
-static const struct hc_driver crisv10_hc_driver =
- {
- .description = hc_name,
- .product_desc = product_desc,
- .hcd_priv_size = sizeof(struct crisv10_hcd),
-
- /* Attaching IRQ handler manualy in probe() */
- /* .irq = crisv10_hcd_irq, */
-
- .flags = HCD_USB11,
-
- /* called to init HCD and root hub */
- .reset = crisv10_hcd_reset,
- .start = crisv10_hcd_start,
-
- /* cleanly make HCD stop writing memory and doing I/O */
- .stop = crisv10_hcd_stop,
-
- /* return current frame number */
- .get_frame_number = crisv10_hcd_get_frame,
-
-
- /* Manage i/o requests via the Transfer Controller */
- .urb_enqueue = tc_urb_enqueue,
- .urb_dequeue = tc_urb_dequeue,
-
- /* hw synch, freeing endpoint resources that urb_dequeue can't */
- .endpoint_disable = tc_endpoint_disable,
-
-
- /* Root Hub support */
- .hub_status_data = rh_status_data_request,
- .hub_control = rh_control_request,
-#ifdef CONFIG_PM
- .hub_suspend = rh_suspend_request,
- .hub_resume = rh_resume_request,
-#endif /* CONFIG_PM */
-#ifdef CONFIG_USB_OTG
- .start_port_reset = crisv10_hcd_start_port_reset,
-#endif /* CONFIG_USB_OTG */
- };
-
-
-/*
- * conversion between pointers to a hcd and the corresponding
- * crisv10_hcd
- */
-
-static inline struct crisv10_hcd *hcd_to_crisv10_hcd(struct usb_hcd *hcd)
-{
- return (struct crisv10_hcd *) hcd->hcd_priv;
-}
-
-static inline struct usb_hcd *crisv10_hcd_to_hcd(struct crisv10_hcd *hcd)
-{
- return container_of((void *) hcd, struct usb_hcd, hcd_priv);
-}
-
-/* check if specified port is in use */
-static inline int port_in_use(unsigned int port)
-{
- return ports & (1 << port);
-}
-
-/* number of ports in use */
-static inline unsigned int num_ports(void)
-{
- unsigned int i, num = 0;
- for (i = 0; i < USB_ROOT_HUB_PORTS; i++)
- if (port_in_use(i))
- num++;
- return num;
-}
-
-/* map hub port number to the port number used internally by the HC */
-static inline unsigned int map_port(unsigned int port)
-{
- unsigned int i, num = 0;
- for (i = 0; i < USB_ROOT_HUB_PORTS; i++)
- if (port_in_use(i))
- if (++num == port)
- return i;
- return -1;
-}
-
-/* size of descriptors in slab cache */
-#ifndef MAX
-#define MAX(x, y) ((x) > (y) ? (x) : (y))
-#endif
-
-
-/******************************************************************/
-/* Hardware Interrupt functions */
-/******************************************************************/
-
-/* Fast interrupt handler for HC */
-static irqreturn_t crisv10_hcd_top_irq(int irq, void *vcd)
-{
- struct usb_hcd *hcd = vcd;
- struct crisv10_irq_reg reg;
- __u32 irq_mask;
- unsigned long flags;
-
- DBFENTER;
-
- ASSERT(hcd != NULL);
- reg.hcd = hcd;
-
- /* Turn of other interrupts while handling these sensitive cases */
- local_irq_save(flags);
-
- /* Read out which interrupts that are flaged */
- irq_mask = *R_USB_IRQ_MASK_READ;
- reg.r_usb_irq_mask_read = irq_mask;
-
- /* Reading R_USB_STATUS clears the ctl_status interrupt. Note that
- R_USB_STATUS must be read before R_USB_EPID_ATTN since reading the latter
- clears the ourun and perror fields of R_USB_STATUS. */
- reg.r_usb_status = *R_USB_STATUS;
-
- /* Reading R_USB_EPID_ATTN clears the iso_eof, bulk_eot and epid_attn
- interrupts. */
- reg.r_usb_epid_attn = *R_USB_EPID_ATTN;
-
- /* Reading R_USB_RH_PORT_STATUS_1 and R_USB_RH_PORT_STATUS_2 clears the
- port_status interrupt. */
- reg.r_usb_rh_port_status_1 = *R_USB_RH_PORT_STATUS_1;
- reg.r_usb_rh_port_status_2 = *R_USB_RH_PORT_STATUS_2;
-
- /* Reading R_USB_FM_NUMBER clears the sof interrupt. */
- /* Note: the lower 11 bits contain the actual frame number, sent with each
- sof. */
- reg.r_usb_fm_number = *R_USB_FM_NUMBER;
-
- /* Interrupts are handled in order of priority. */
- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, port_status)) {
- crisv10_hcd_port_status_irq(&reg);
- }
- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, epid_attn)) {
- crisv10_hcd_epid_attn_irq(&reg);
- }
- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, ctl_status)) {
- crisv10_hcd_ctl_status_irq(&reg);
- }
- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, iso_eof)) {
- crisv10_hcd_isoc_eof_irq(&reg);
- }
- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, bulk_eot)) {
- /* Update/restart the bulk start timer since obviously the channel is
- running. */
- mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL);
- /* Update/restart the bulk eot timer since we just received an bulk eot
- interrupt. */
- mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL);
-
- /* Check for finished bulk transfers on epids */
- check_finished_bulk_tx_epids(hcd, 0);
- }
- local_irq_restore(flags);
-
- DBFEXIT;
- return IRQ_HANDLED;
-}
-
-
-void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg) {
- struct usb_hcd *hcd = reg->hcd;
- struct crisv10_urb_priv *urb_priv;
- int epid;
- DBFENTER;
-
- for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
- if (test_bit(epid, (void *)&reg->r_usb_epid_attn)) {
- struct urb *urb;
- __u32 ept_data;
- int error_code;
-
- if (epid == DUMMY_EPID || epid == INVALID_EPID) {
- /* We definitely don't care about these ones. Besides, they are
- always disabled, so any possible disabling caused by the
- epid attention interrupt is irrelevant. */
- continue;
- }
-
- if(!epid_inuse(epid)) {
- irq_err("Epid attention on epid:%d that isn't in use\n", epid);
- printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
- debug_epid(epid);
- continue;
- }
-
- /* Note that although there are separate R_USB_EPT_DATA and
- R_USB_EPT_DATA_ISO registers, they are located at the same address and
- are of the same size. In other words, this read should be ok for isoc
- also. */
- ept_data = etrax_epid_get(epid);
- error_code = IO_EXTRACT(R_USB_EPT_DATA, error_code, ept_data);
-
- /* Get the active URB for this epid. We blatantly assume
- that only this URB could have caused the epid attention. */
- urb = activeUrbList[epid];
- if (urb == NULL) {
- irq_err("Attention on epid:%d error:%d with no active URB.\n",
- epid, error_code);
- printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
- debug_epid(epid);
- continue;
- }
-
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
-
- /* Using IO_STATE_VALUE on R_USB_EPT_DATA should be ok for isoc also. */
- if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
-
- /* Isoc traffic doesn't have error_count_in/error_count_out. */
- if ((usb_pipetype(urb->pipe) != PIPE_ISOCHRONOUS) &&
- (IO_EXTRACT(R_USB_EPT_DATA, error_count_in, ept_data) == 3 ||
- IO_EXTRACT(R_USB_EPT_DATA, error_count_out, ept_data) == 3)) {
- /* Check if URB allready is marked for late-finish, we can get
- several 3rd error for Intr traffic when a device is unplugged */
- if(urb_priv->later_data == NULL) {
- /* 3rd error. */
- irq_warn("3rd error for epid:%d (%s %s) URB:0x%x[%d]\n", epid,
- str_dir(urb->pipe), str_type(urb->pipe),
- (unsigned int)urb, urb_priv->urb_num);
-
- tc_finish_urb_later(hcd, urb, -EPROTO);
- }
-
- } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) {
- irq_warn("Perror for epid:%d\n", epid);
- printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff);
- printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
- __dump_urb(urb);
- debug_epid(epid);
-
- if (!(ept_data & IO_MASK(R_USB_EPT_DATA, valid))) {
- /* invalid ep_id */
- panic("Perror because of invalid epid."
- " Deconfigured too early?");
- } else {
- /* past eof1, near eof, zout transfer, setup transfer */
- /* Dump the urb and the relevant EP descriptor. */
- panic("Something wrong with DMA descriptor contents."
- " Too much traffic inserted?");
- }
- } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) {
- /* buffer ourun */
- printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff);
- printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
- __dump_urb(urb);
- debug_epid(epid);
-
- panic("Buffer overrun/underrun for epid:%d. DMA too busy?", epid);
- } else {
- irq_warn("Attention on epid:%d (%s %s) with no error code\n", epid,
- str_dir(urb->pipe), str_type(urb->pipe));
- printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status);
- __dump_urb(urb);
- debug_epid(epid);
- }
-
- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code,
- stall)) {
- /* Not really a protocol error, just says that the endpoint gave
- a stall response. Note that error_code cannot be stall for isoc. */
- if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
- panic("Isoc traffic cannot stall");
- }
-
- tc_dbg("Stall for epid:%d (%s %s) URB:0x%x\n", epid,
- str_dir(urb->pipe), str_type(urb->pipe), (unsigned int)urb);
- tc_finish_urb(hcd, urb, -EPIPE);
-
- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code,
- bus_error)) {
- /* Two devices responded to a transaction request. Must be resolved
- by software. FIXME: Reset ports? */
- panic("Bus error for epid %d."
- " Two devices responded to transaction request\n",
- epid);
-
- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code,
- buffer_error)) {
- /* DMA overrun or underrun. */
- irq_warn("Buffer overrun/underrun for epid:%d (%s %s)\n", epid,
- str_dir(urb->pipe), str_type(urb->pipe));
-
- /* It seems that error_code = buffer_error in
- R_USB_EPT_DATA/R_USB_EPT_DATA_ISO and ourun = yes in R_USB_STATUS
- are the same error. */
- tc_finish_urb(hcd, urb, -EPROTO);
- } else {
- irq_warn("Unknown attention on epid:%d (%s %s)\n", epid,
- str_dir(urb->pipe), str_type(urb->pipe));
- dump_ept_data(epid);
- }
- }
- }
- DBFEXIT;
-}
-
-void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg)
-{
- __u16 port_reg[USB_ROOT_HUB_PORTS];
- DBFENTER;
- port_reg[0] = reg->r_usb_rh_port_status_1;
- port_reg[1] = reg->r_usb_rh_port_status_2;
- rh_port_status_change(port_reg);
- DBFEXIT;
-}
-
-void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg)
-{
- int epid;
- struct urb *urb;
- struct crisv10_urb_priv *urb_priv;
-
- DBFENTER;
-
- for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) {
-
- /* Only check epids that are in use, is valid and has SB list */
- if (!epid_inuse(epid) || epid == INVALID_EPID ||
- TxIsocEPList[epid].sub == 0 || epid == DUMMY_EPID) {
- /* Nothing here to see. */
- continue;
- }
- ASSERT(epid_isoc(epid));
-
- /* Get the active URB for this epid (if any). */
- urb = activeUrbList[epid];
- if (urb == 0) {
- isoc_warn("Ignoring NULL urb for epid:%d\n", epid);
- continue;
- }
- if(!epid_out_traffic(epid)) {
- /* Sanity check. */
- ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS);
-
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
-
- if (urb_priv->urb_state == NOT_STARTED) {
- /* If ASAP is not set and urb->start_frame is the current frame,
- start the transfer. */
- if (!(urb->transfer_flags & URB_ISO_ASAP) &&
- (urb->start_frame == (*R_USB_FM_NUMBER & 0x7ff))) {
- /* EP should not be enabled if we're waiting for start_frame */
- ASSERT((TxIsocEPList[epid].command &
- IO_STATE(USB_EP_command, enable, yes)) == 0);
-
- isoc_warn("Enabling isoc IN EP descr for epid %d\n", epid);
- TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
-
- /* This urb is now active. */
- urb_priv->urb_state = STARTED;
- continue;
- }
- }
- }
- }
-
- DBFEXIT;
-}
-
-void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg)
-{
- struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(reg->hcd);
-
- DBFENTER;
- ASSERT(crisv10_hcd);
-
-/* irq_dbg("ctr_status_irq, controller status: %s\n",
- hcd_status_to_str(reg->r_usb_status));*/
-
- /* FIXME: What should we do if we get ourun or perror? Dump the EP and SB
- list for the corresponding epid? */
- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) {
- panic("USB controller got ourun.");
- }
- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) {
-
- /* Before, etrax_usb_do_intr_recover was called on this epid if it was
- an interrupt pipe. I don't see how re-enabling all EP descriptors
- will help if there was a programming error. */
- panic("USB controller got perror.");
- }
-
- /* Keep track of USB Controller, if it's running or not */
- if(reg->r_usb_status & IO_STATE(R_USB_STATUS, running, yes)) {
- crisv10_hcd->running = 1;
- } else {
- crisv10_hcd->running = 0;
- }
-
- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, device_mode)) {
- /* We should never operate in device mode. */
- panic("USB controller in device mode.");
- }
-
- /* Set the flag to avoid getting "Unlink after no-IRQ? Controller is probably
- using the wrong IRQ" from hcd_unlink_urb() in drivers/usb/core/hcd.c */
- set_bit(HCD_FLAG_SAW_IRQ, &reg->hcd->flags);
-
- DBFEXIT;
-}
-
-
-/******************************************************************/
-/* Host Controller interface functions */
-/******************************************************************/
-
-static inline void crisv10_ready_wait(void) {
- volatile int timeout = 10000;
- /* Check the busy bit of USB controller in Etrax */
- while((*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)) &&
- (timeout-- > 0));
-}
-
-/* reset host controller */
-static int crisv10_hcd_reset(struct usb_hcd *hcd)
-{
- DBFENTER;
- hcd_dbg(hcd, "reset\n");
-
-
- /* Reset the USB interface. */
- /*
- *R_USB_COMMAND =
- IO_STATE(R_USB_COMMAND, port_sel, nop) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, reset);
- nop();
- */
- DBFEXIT;
- return 0;
-}
-
-/* start host controller */
-static int crisv10_hcd_start(struct usb_hcd *hcd)
-{
- DBFENTER;
- hcd_dbg(hcd, "start\n");
-
- crisv10_ready_wait();
-
- /* Start processing of USB traffic. */
- *R_USB_COMMAND =
- IO_STATE(R_USB_COMMAND, port_sel, nop) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
-
- nop();
-
- hcd->state = HC_STATE_RUNNING;
-
- DBFEXIT;
- return 0;
-}
-
-/* stop host controller */
-static void crisv10_hcd_stop(struct usb_hcd *hcd)
-{
- DBFENTER;
- hcd_dbg(hcd, "stop\n");
- crisv10_hcd_reset(hcd);
- DBFEXIT;
-}
-
-/* return the current frame number */
-static int crisv10_hcd_get_frame(struct usb_hcd *hcd)
-{
- DBFENTER;
- DBFEXIT;
- return (*R_USB_FM_NUMBER & 0x7ff);
-}
-
-#ifdef CONFIG_USB_OTG
-
-static int crisv10_hcd_start_port_reset(struct usb_hcd *hcd, unsigned port)
-{
- return 0; /* no-op for now */
-}
-
-#endif /* CONFIG_USB_OTG */
-
-
-/******************************************************************/
-/* Root Hub functions */
-/******************************************************************/
-
-/* root hub status */
-static const struct usb_hub_status rh_hub_status =
- {
- .wHubStatus = 0,
- .wHubChange = 0,
- };
-
-/* root hub descriptor */
-static const u8 rh_hub_descr[] =
- {
- 0x09, /* bDescLength */
- 0x29, /* bDescriptorType */
- USB_ROOT_HUB_PORTS, /* bNbrPorts */
- 0x00, /* wHubCharacteristics */
- 0x00,
- 0x01, /* bPwrOn2pwrGood */
- 0x00, /* bHubContrCurrent */
- 0x00, /* DeviceRemovable */
- 0xff /* PortPwrCtrlMask */
- };
-
-/* Actual holder of root hub status*/
-struct crisv10_rh rh;
-
-/* Initialize root hub data structures (called from dvdrv_hcd_probe()) */
-int rh_init(void) {
- int i;
- /* Reset port status flags */
- for (i = 0; i < USB_ROOT_HUB_PORTS; i++) {
- rh.wPortChange[i] = 0;
- rh.wPortStatusPrev[i] = 0;
- }
- return 0;
-}
-
-#define RH_FEAT_MASK ((1<<USB_PORT_FEAT_CONNECTION)|\
- (1<<USB_PORT_FEAT_ENABLE)|\
- (1<<USB_PORT_FEAT_SUSPEND)|\
- (1<<USB_PORT_FEAT_RESET))
-
-/* Handle port status change interrupt (called from bottom part interrupt) */
-void rh_port_status_change(__u16 port_reg[]) {
- int i;
- __u16 wChange;
-
- for(i = 0; i < USB_ROOT_HUB_PORTS; i++) {
- /* Xor out changes since last read, masked for important flags */
- wChange = (port_reg[i] & RH_FEAT_MASK) ^ rh.wPortStatusPrev[i];
- /* Or changes together with (if any) saved changes */
- rh.wPortChange[i] |= wChange;
- /* Save new status */
- rh.wPortStatusPrev[i] = port_reg[i];
-
- if(wChange) {
- rh_dbg("Interrupt port_status change port%d: %s Current-status:%s\n", i+1,
- port_status_to_str(wChange),
- port_status_to_str(port_reg[i]));
- }
- }
-}
-
-/* Construct port status change bitmap for the root hub */
-static int rh_status_data_request(struct usb_hcd *hcd, char *buf)
-{
- struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd);
- unsigned int i;
-
- DBFENTER;
- /*
- * corresponds to hub status change EP (USB 2.0 spec section 11.13.4)
- * return bitmap indicating ports with status change
- */
- *buf = 0;
- spin_lock(&crisv10_hcd->lock);
- for (i = 1; i <= crisv10_hcd->num_ports; i++) {
- if (rh.wPortChange[map_port(i)]) {
- *buf |= (1 << i);
- rh_dbg("rh_status_data_request, change on port %d: %s Current Status: %s\n", i,
- port_status_to_str(rh.wPortChange[map_port(i)]),
- port_status_to_str(rh.wPortStatusPrev[map_port(i)]));
- }
- }
- spin_unlock(&crisv10_hcd->lock);
- DBFEXIT;
- return *buf == 0 ? 0 : 1;
-}
-
-/* Handle a control request for the root hub (called from hcd_driver) */
-static int rh_control_request(struct usb_hcd *hcd,
- u16 typeReq,
- u16 wValue,
- u16 wIndex,
- char *buf,
- u16 wLength) {
-
- struct crisv10_hcd *crisv10_hcd = hcd_to_crisv10_hcd(hcd);
- int retval = 0;
- int len;
- DBFENTER;
-
- switch (typeReq) {
- case GetHubDescriptor:
- rh_dbg("GetHubDescriptor\n");
- len = min_t(unsigned int, sizeof rh_hub_descr, wLength);
- memcpy(buf, rh_hub_descr, len);
- buf[2] = crisv10_hcd->num_ports;
- break;
- case GetHubStatus:
- rh_dbg("GetHubStatus\n");
- len = min_t(unsigned int, sizeof rh_hub_status, wLength);
- memcpy(buf, &rh_hub_status, len);
- break;
- case GetPortStatus:
- if (!wIndex || wIndex > crisv10_hcd->num_ports)
- goto error;
- rh_dbg("GetportStatus, port:%d change:%s status:%s\n", wIndex,
- port_status_to_str(rh.wPortChange[map_port(wIndex)]),
- port_status_to_str(rh.wPortStatusPrev[map_port(wIndex)]));
- *(u16 *) buf = cpu_to_le16(rh.wPortStatusPrev[map_port(wIndex)]);
- *(u16 *) (buf + 2) = cpu_to_le16(rh.wPortChange[map_port(wIndex)]);
- break;
- case SetHubFeature:
- rh_dbg("SetHubFeature\n");
- case ClearHubFeature:
- rh_dbg("ClearHubFeature\n");
- switch (wValue) {
- case C_HUB_OVER_CURRENT:
- case C_HUB_LOCAL_POWER:
- rh_warn("Not implemented hub request:%d \n", typeReq);
- /* not implemented */
- break;
- default:
- goto error;
- }
- break;
- case SetPortFeature:
- if (!wIndex || wIndex > crisv10_hcd->num_ports)
- goto error;
- if(rh_set_port_feature(map_port(wIndex), wValue))
- goto error;
- break;
- case ClearPortFeature:
- if (!wIndex || wIndex > crisv10_hcd->num_ports)
- goto error;
- if(rh_clear_port_feature(map_port(wIndex), wValue))
- goto error;
- break;
- default:
- rh_warn("Unknown hub request: %d\n", typeReq);
- error:
- retval = -EPIPE;
- }
- DBFEXIT;
- return retval;
-}
-
-int rh_set_port_feature(__u8 bPort, __u16 wFeature) {
- __u8 bUsbCommand = 0;
- __u8 reset_cnt;
- switch(wFeature) {
- case USB_PORT_FEAT_RESET:
- rh_dbg("SetPortFeature: reset\n");
-
- if (rh.wPortStatusPrev[bPort] &
- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes))
- {
- __u8 restart_controller = 0;
-
- if ( (rh.wPortStatusPrev[0] &
- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) &&
- (rh.wPortStatusPrev[1] &
- IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, yes)) )
- {
- /* Both ports is enabled. The USB controller will not change state. */
- restart_controller = 0;
- }
- else
- {
- /* Only ports is enabled. The USB controller will change state and
- must be restarted. */
- restart_controller = 1;
- }
- /*
- In ETRAX 100LX it's not possible to reset an enabled root hub port.
- The workaround is to disable and enable the port before resetting it.
- Disabling the port can, if both ports are disabled at once, cause the
- USB controller to change state to HOST_MODE state.
- The USB controller state transition causes a lot of unwanted
- interrupts that must be avoided.
- Disabling the USB controller status and port status interrupts before
- disabling/resetting the port stops these interrupts.
-
- These actions are performed:
- 1. Disable USB controller status and port status interrupts.
- 2. Disable the port
- 3. Wait for the port to be disabled.
- 4. Enable the port.
- 5. Wait for the port to be enabled.
- 6. Reset the port.
- 7. Wait for for the reset to end.
- 8. Wait for the USB controller entering started state.
- 9. Order the USB controller to running state.
- 10. Wait for the USB controller reaching running state.
- 11. Clear all interrupts generated during the disable/enable/reset
- procedure.
- 12. Enable the USB controller status and port status interrupts.
- */
-
- /* 1. Disable USB controller status and USB port status interrupts. */
- *R_USB_IRQ_MASK_CLR = IO_STATE(R_USB_IRQ_MASK_CLR, ctl_status, clr);
- __asm__ __volatile__ (" nop");
- *R_USB_IRQ_MASK_CLR = IO_STATE(R_USB_IRQ_MASK_CLR, port_status, clr);
- __asm__ __volatile__ (" nop");
-
- {
-
- /* Since an root hub port reset shall be 50 ms and the ETRAX 100LX
- root hub port reset is 10 ms we must perform 5 port resets to
- achieve a proper root hub port reset. */
- for (reset_cnt = 0; reset_cnt < 5; reset_cnt ++)
- {
- rh_dbg("Disable Port %d\n", bPort + 1);
-
- /* 2. Disable the port*/
- if (bPort == 0)
- {
- *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, yes);
- }
- else
- {
- *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, yes);
- }
-
- /* 3. Wait for the port to be disabled. */
- while ( (bPort == 0) ?
- *R_USB_RH_PORT_STATUS_1 &
- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes) :
- *R_USB_RH_PORT_STATUS_2 &
- IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, yes) ) {}
-
- rh_dbg("Port %d is disabled. Enable it!\n", bPort + 1);
-
- /* 4. Enable the port. */
- if (bPort == 0)
- {
- *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no);
- }
- else
- {
- *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no);
- }
-
- /* 5. Wait for the port to be enabled again. */
- while (!( (bPort == 0) ?
- *R_USB_RH_PORT_STATUS_1 &
- IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes) :
- *R_USB_RH_PORT_STATUS_2 &
- IO_STATE(R_USB_RH_PORT_STATUS_2, connected, yes) ) ) {}
-
- rh_dbg("Port %d is enabled.\n", bPort + 1);
-
- /* 6. Reset the port */
- crisv10_ready_wait();
- *R_USB_COMMAND =
- ( (bPort == 0) ?
- IO_STATE(R_USB_COMMAND, port_sel, port1):
- IO_STATE(R_USB_COMMAND, port_sel, port2) ) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, busy, no) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, nop);
- rh_dbg("Port %d is resetting.\n", bPort + 1);
-
- /* 7. The USB specification says that we should wait for at least
- 10ms for device recover */
- udelay(10500); /* 10,5ms blocking wait */
-
- crisv10_ready_wait();
- }
- }
-
-
- /* Check if the USB controller needs to be restarted. */
- if (restart_controller)
- {
- /* 8. Wait for the USB controller entering started state. */
- while (!(*R_USB_STATUS & IO_STATE(R_USB_STATUS, started, yes))) {}
-
- /* 9. Order the USB controller to running state. */
- crisv10_ready_wait();
- *R_USB_COMMAND =
- IO_STATE(R_USB_COMMAND, port_sel, nop) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, busy, no) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
-
- /* 10. Wait for the USB controller reaching running state. */
- while (!(*R_USB_STATUS & IO_STATE(R_USB_STATUS, running, yes))) {}
- }
-
- /* 11. Clear any controller or port satus interrupts before enabling
- the interrupts. */
- {
- u16 dummy;
-
- /* Clear the port status interrupt of the reset port. */
- if (bPort == 0)
- {
- rh_dbg("Clearing port 1 interrupts\n");
- dummy = *R_USB_RH_PORT_STATUS_1;
- }
- else
- {
- rh_dbg("Clearing port 2 interrupts\n");
- dummy = *R_USB_RH_PORT_STATUS_2;
- }
-
- if (restart_controller)
- {
- /* The USB controller is restarted. Clear all interupts. */
- rh_dbg("Clearing all interrupts\n");
- dummy = *R_USB_STATUS;
- dummy = *R_USB_RH_PORT_STATUS_1;
- dummy = *R_USB_RH_PORT_STATUS_2;
- }
- }
-
- /* 12. Enable USB controller status and USB port status interrupts. */
- *R_USB_IRQ_MASK_SET = IO_STATE(R_USB_IRQ_MASK_SET, ctl_status, set);
- __asm__ __volatile__ (" nop");
- *R_USB_IRQ_MASK_SET = IO_STATE(R_USB_IRQ_MASK_SET, port_status, set);
- __asm__ __volatile__ (" nop");
-
- }
- else
- {
-
- bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, reset);
- /* Select which port via the port_sel field */
- bUsbCommand |= IO_FIELD(R_USB_COMMAND, port_sel, bPort+1);
-
- /* Make sure the controller isn't busy. */
- crisv10_ready_wait();
- /* Send out the actual command to the USB controller */
- *R_USB_COMMAND = bUsbCommand;
-
- /* Wait a while for controller to first become started after port reset */
- udelay(12000); /* 12ms blocking wait */
-
- /* Make sure the controller isn't busy. */
- crisv10_ready_wait();
-
- /* If all enabled ports were disabled the host controller goes down into
- started mode, so we need to bring it back into the running state.
- (This is safe even if it's already in the running state.) */
- *R_USB_COMMAND =
- IO_STATE(R_USB_COMMAND, port_sel, nop) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
- }
-
- break;
- case USB_PORT_FEAT_SUSPEND:
- rh_dbg("SetPortFeature: suspend\n");
- bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, suspend);
- goto set;
- break;
- case USB_PORT_FEAT_POWER:
- rh_dbg("SetPortFeature: power\n");
- break;
- case USB_PORT_FEAT_C_CONNECTION:
- rh_dbg("SetPortFeature: c_connection\n");
- break;
- case USB_PORT_FEAT_C_RESET:
- rh_dbg("SetPortFeature: c_reset\n");
- break;
- case USB_PORT_FEAT_C_OVER_CURRENT:
- rh_dbg("SetPortFeature: c_over_current\n");
- break;
-
- set:
- /* Select which port via the port_sel field */
- bUsbCommand |= IO_FIELD(R_USB_COMMAND, port_sel, bPort+1);
-
- /* Make sure the controller isn't busy. */
- crisv10_ready_wait();
- /* Send out the actual command to the USB controller */
- *R_USB_COMMAND = bUsbCommand;
- break;
- default:
- rh_dbg("SetPortFeature: unknown feature\n");
- return -1;
- }
- return 0;
-}
-
-int rh_clear_port_feature(__u8 bPort, __u16 wFeature) {
- switch(wFeature) {
- case USB_PORT_FEAT_ENABLE:
- rh_dbg("ClearPortFeature: enable\n");
- rh_disable_port(bPort);
- break;
- case USB_PORT_FEAT_SUSPEND:
- rh_dbg("ClearPortFeature: suspend\n");
- break;
- case USB_PORT_FEAT_POWER:
- rh_dbg("ClearPortFeature: power\n");
- break;
-
- case USB_PORT_FEAT_C_ENABLE:
- rh_dbg("ClearPortFeature: c_enable\n");
- goto clear;
- case USB_PORT_FEAT_C_SUSPEND:
- rh_dbg("ClearPortFeature: c_suspend\n");
- goto clear;
- case USB_PORT_FEAT_C_CONNECTION:
- rh_dbg("ClearPortFeature: c_connection\n");
- goto clear;
- case USB_PORT_FEAT_C_OVER_CURRENT:
- rh_dbg("ClearPortFeature: c_over_current\n");
- goto clear;
- case USB_PORT_FEAT_C_RESET:
- rh_dbg("ClearPortFeature: c_reset\n");
- goto clear;
- clear:
- rh.wPortChange[bPort] &= ~(1 << (wFeature - 16));
- break;
- default:
- rh_dbg("ClearPortFeature: unknown feature\n");
- return -1;
- }
- return 0;
-}
-
-
-#ifdef CONFIG_PM
-/* Handle a suspend request for the root hub (called from hcd_driver) */
-static int rh_suspend_request(struct usb_hcd *hcd)
-{
- return 0; /* no-op for now */
-}
-
-/* Handle a resume request for the root hub (called from hcd_driver) */
-static int rh_resume_request(struct usb_hcd *hcd)
-{
- return 0; /* no-op for now */
-}
-#endif /* CONFIG_PM */
-
-
-
-/* Wrapper function for workaround port disable registers in USB controller */
-static void rh_disable_port(unsigned int port) {
- volatile int timeout = 10000;
- volatile char* usb_portx_disable;
- switch(port) {
- case 0:
- usb_portx_disable = R_USB_PORT1_DISABLE;
- break;
- case 1:
- usb_portx_disable = R_USB_PORT2_DISABLE;
- break;
- default:
- /* Invalid port index */
- return;
- }
- /* Set disable flag in special register */
- *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, yes);
- /* Wait until not enabled anymore */
- while((rh.wPortStatusPrev[port] &
- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) &&
- (timeout-- > 0));
-
- /* clear disable flag in special register */
- *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, no);
- rh_info("Physical port %d disabled\n", port+1);
-}
-
-
-/******************************************************************/
-/* Transfer Controller (TC) functions */
-/******************************************************************/
-
-/* FIXME: Should RX_BUF_SIZE be a config option, or maybe we should adjust it
- dynamically?
- To adjust it dynamically we would have to get an interrupt when we reach
- the end of the rx descriptor list, or when we get close to the end, and
- then allocate more descriptors. */
-#define NBR_OF_RX_DESC 512
-#define RX_DESC_BUF_SIZE 1024
-#define RX_BUF_SIZE (NBR_OF_RX_DESC * RX_DESC_BUF_SIZE)
-
-
-/* Local variables for Transfer Controller */
-/* --------------------------------------- */
-
-/* This is a circular (double-linked) list of the active urbs for each epid.
- The head is never removed, and new urbs are linked onto the list as
- urb_entry_t elements. Don't reference urb_list directly; use the wrapper
- functions instead (which includes spin_locks) */
-static struct list_head urb_list[NBR_OF_EPIDS];
-
-/* Read about the need and usage of this lock in submit_ctrl_urb. */
-/* Lock for URB lists for each EPID */
-static spinlock_t urb_list_lock;
-
-/* Lock for EPID array register (R_USB_EPT_x) in Etrax */
-static spinlock_t etrax_epid_lock;
-
-/* Lock for dma8 sub0 handling */
-static spinlock_t etrax_dma8_sub0_lock;
-
-/* DMA IN cache bug. Align the DMA IN buffers to 32 bytes, i.e. a cache line.
- Since RX_DESC_BUF_SIZE is 1024 is a multiple of 32, all rx buffers will be
- cache aligned. */
-static volatile unsigned char RxBuf[RX_BUF_SIZE] __attribute__ ((aligned (32)));
-static volatile struct USB_IN_Desc RxDescList[NBR_OF_RX_DESC] __attribute__ ((aligned (4)));
-
-/* Pointers into RxDescList. */
-static volatile struct USB_IN_Desc *myNextRxDesc;
-static volatile struct USB_IN_Desc *myLastRxDesc;
-
-/* A zout transfer makes a memory access at the address of its buf pointer,
- which means that setting this buf pointer to 0 will cause an access to the
- flash. In addition to this, setting sw_len to 0 results in a 16/32 bytes
- (depending on DMA burst size) transfer.
- Instead, we set it to 1, and point it to this buffer. */
-static int zout_buffer[4] __attribute__ ((aligned (4)));
-
-/* Cache for allocating new EP and SB descriptors. */
-static struct kmem_cache *usb_desc_cache;
-
-/* Cache for the data allocated in the isoc descr top half. */
-static struct kmem_cache *isoc_compl_cache;
-
-/* Cache for the data allocated when delayed finishing of URBs */
-static struct kmem_cache *later_data_cache;
-
-
-/* Counter to keep track of how many Isoc EP we have sat up. Used to enable
- and disable iso_eof interrupt. We only need these interrupts when we have
- Isoc data endpoints (consumes CPU cycles).
- FIXME: This could be more fine granular, so this interrupt is only enabled
- when we have a In Isoc URB not URB_ISO_ASAP flaged queued. */
-static int isoc_epid_counter;
-
-/* Protecting wrapper functions for R_USB_EPT_x */
-/* -------------------------------------------- */
-static inline void etrax_epid_set(__u8 index, __u32 data) {
- unsigned long flags;
- spin_lock_irqsave(&etrax_epid_lock, flags);
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
- nop();
- *R_USB_EPT_DATA = data;
- spin_unlock_irqrestore(&etrax_epid_lock, flags);
-}
-
-static inline void etrax_epid_clear_error(__u8 index) {
- unsigned long flags;
- spin_lock_irqsave(&etrax_epid_lock, flags);
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
- nop();
- *R_USB_EPT_DATA &=
- ~(IO_MASK(R_USB_EPT_DATA, error_count_in) |
- IO_MASK(R_USB_EPT_DATA, error_count_out) |
- IO_MASK(R_USB_EPT_DATA, error_code));
- spin_unlock_irqrestore(&etrax_epid_lock, flags);
-}
-
-static inline void etrax_epid_set_toggle(__u8 index, __u8 dirout,
- __u8 toggle) {
- unsigned long flags;
- spin_lock_irqsave(&etrax_epid_lock, flags);
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
- nop();
- if(dirout) {
- *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_out);
- *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_out, toggle);
- } else {
- *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_in);
- *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_in, toggle);
- }
- spin_unlock_irqrestore(&etrax_epid_lock, flags);
-}
-
-static inline __u8 etrax_epid_get_toggle(__u8 index, __u8 dirout) {
- unsigned long flags;
- __u8 toggle;
- spin_lock_irqsave(&etrax_epid_lock, flags);
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
- nop();
- if (dirout) {
- toggle = IO_EXTRACT(R_USB_EPT_DATA, t_out, *R_USB_EPT_DATA);
- } else {
- toggle = IO_EXTRACT(R_USB_EPT_DATA, t_in, *R_USB_EPT_DATA);
- }
- spin_unlock_irqrestore(&etrax_epid_lock, flags);
- return toggle;
-}
-
-
-static inline __u32 etrax_epid_get(__u8 index) {
- unsigned long flags;
- __u32 data;
- spin_lock_irqsave(&etrax_epid_lock, flags);
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index);
- nop();
- data = *R_USB_EPT_DATA;
- spin_unlock_irqrestore(&etrax_epid_lock, flags);
- return data;
-}
-
-
-
-
-/* Main functions for Transfer Controller */
-/* -------------------------------------- */
-
-/* Init structs, memories and lists used by Transfer Controller */
-int tc_init(struct usb_hcd *hcd) {
- int i;
- /* Clear software state info for all epids */
- memset(epid_state, 0, sizeof(struct etrax_epid) * NBR_OF_EPIDS);
-
- /* Set Invalid and Dummy as being in use and disabled */
- epid_state[INVALID_EPID].inuse = 1;
- epid_state[DUMMY_EPID].inuse = 1;
- epid_state[INVALID_EPID].disabled = 1;
- epid_state[DUMMY_EPID].disabled = 1;
-
- /* Clear counter for how many Isoc epids we have sat up */
- isoc_epid_counter = 0;
-
- /* Initialize the urb list by initiating a head for each list.
- Also reset list hodling active URB for each epid */
- for (i = 0; i < NBR_OF_EPIDS; i++) {
- INIT_LIST_HEAD(&urb_list[i]);
- activeUrbList[i] = NULL;
- }
-
- /* Init lock for URB lists */
- spin_lock_init(&urb_list_lock);
- /* Init lock for Etrax R_USB_EPT register */
- spin_lock_init(&etrax_epid_lock);
- /* Init lock for Etrax dma8 sub0 handling */
- spin_lock_init(&etrax_dma8_sub0_lock);
-
- /* We use kmem_cache_* to make sure that all DMA desc. are dword aligned */
-
- /* Note that we specify sizeof(struct USB_EP_Desc) as the size, but also
- allocate SB descriptors from this cache. This is ok since
- sizeof(struct USB_EP_Desc) == sizeof(struct USB_SB_Desc). */
- usb_desc_cache = kmem_cache_create("usb_desc_cache",
- sizeof(struct USB_EP_Desc), 0,
- SLAB_HWCACHE_ALIGN, 0);
- if(usb_desc_cache == NULL) {
- return -ENOMEM;
- }
-
- /* Create slab cache for speedy allocation of memory for isoc bottom-half
- interrupt handling */
- isoc_compl_cache =
- kmem_cache_create("isoc_compl_cache",
- sizeof(struct crisv10_isoc_complete_data),
- 0, SLAB_HWCACHE_ALIGN, 0);
- if(isoc_compl_cache == NULL) {
- return -ENOMEM;
- }
-
- /* Create slab cache for speedy allocation of memory for later URB finish
- struct */
- later_data_cache =
- kmem_cache_create("later_data_cache",
- sizeof(struct urb_later_data),
- 0, SLAB_HWCACHE_ALIGN, 0);
- if(later_data_cache == NULL) {
- return -ENOMEM;
- }
-
-
- /* Initiate the bulk start timer. */
- init_timer(&bulk_start_timer);
- bulk_start_timer.expires = jiffies + BULK_START_TIMER_INTERVAL;
- bulk_start_timer.function = tc_bulk_start_timer_func;
- add_timer(&bulk_start_timer);
-
-
- /* Initiate the bulk eot timer. */
- init_timer(&bulk_eot_timer);
- bulk_eot_timer.expires = jiffies + BULK_EOT_TIMER_INTERVAL;
- bulk_eot_timer.function = tc_bulk_eot_timer_func;
- bulk_eot_timer.data = (unsigned long)hcd;
- add_timer(&bulk_eot_timer);
-
- return 0;
-}
-
-/* Uninitialize all resources used by Transfer Controller */
-void tc_destroy(void) {
-
- /* Destroy all slab cache */
- kmem_cache_destroy(usb_desc_cache);
- kmem_cache_destroy(isoc_compl_cache);
- kmem_cache_destroy(later_data_cache);
-
- /* Remove timers */
- del_timer(&bulk_start_timer);
- del_timer(&bulk_eot_timer);
-}
-
-static void restart_dma8_sub0(void) {
- unsigned long flags;
- spin_lock_irqsave(&etrax_dma8_sub0_lock, flags);
- /* Verify that the dma is not running */
- if ((*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd)) == 0) {
- struct USB_EP_Desc *ep = (struct USB_EP_Desc *)phys_to_virt(*R_DMA_CH8_SUB0_EP);
- while (DUMMY_EPID == IO_EXTRACT(USB_EP_command, epid, ep->command)) {
- ep = (struct USB_EP_Desc *)phys_to_virt(ep->next);
- }
- /* Advance the DMA to the next EP descriptor that is not a DUMMY_EPID. */
- *R_DMA_CH8_SUB0_EP = virt_to_phys(ep);
- /* Restart the DMA */
- *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start);
- }
- spin_unlock_irqrestore(&etrax_dma8_sub0_lock, flags);
-}
-
-/* queue an URB with the transfer controller (called from hcd_driver) */
-static int tc_urb_enqueue(struct usb_hcd *hcd,
- struct urb *urb,
- gfp_t mem_flags) {
- int epid;
- int retval;
- int bustime = 0;
- int maxpacket;
- unsigned long flags;
- struct crisv10_urb_priv *urb_priv;
- struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd);
- DBFENTER;
-
- if(!(crisv10_hcd->running)) {
- /* The USB Controller is not running, probably because no device is
- attached. No idea to enqueue URBs then */
- tc_warn("Rejected enqueueing of URB:0x%x because no dev attached\n",
- (unsigned int)urb);
- return -ENOENT;
- }
-
- maxpacket = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe));
- /* Special case check for In Isoc transfers. Specification states that each
- In Isoc transfer consists of one packet and therefore it should fit into
- the transfer-buffer of an URB.
- We do the check here to be sure (an invalid scenario can be produced with
- parameters to the usbtest suite) */
- if(usb_pipeisoc(urb->pipe) && usb_pipein(urb->pipe) &&
- (urb->transfer_buffer_length < maxpacket)) {
- tc_err("Submit In Isoc URB with buffer length:%d to pipe with maxpacketlen: %d\n", urb->transfer_buffer_length, maxpacket);
- return -EMSGSIZE;
- }
-
- /* Check if there is a epid for URBs destination, if not this function
- set up one. */
- epid = tc_setup_epid(urb->ep, urb, mem_flags);
- if (epid < 0) {
- tc_err("Failed setup epid:%d for URB:0x%x\n", epid, (unsigned int)urb);
- DBFEXIT;
- return -ENOMEM;
- }
-
- if(urb == activeUrbList[epid]) {
- tc_err("Resubmition of allready active URB:0x%x\n", (unsigned int)urb);
- return -ENXIO;
- }
-
- if(urb_list_entry(urb, epid)) {
- tc_err("Resubmition of allready queued URB:0x%x\n", (unsigned int)urb);
- return -ENXIO;
- }
-
- /* If we actively have flaged endpoint as disabled then refuse submition */
- if(epid_state[epid].disabled) {
- return -ENOENT;
- }
-
- /* Allocate and init HC-private data for URB */
- if(urb_priv_create(hcd, urb, epid, mem_flags) != 0) {
- DBFEXIT;
- return -ENOMEM;
- }
- urb_priv = urb->hcpriv;
-
- /* Check if there is enough bandwidth for periodic transfer */
- if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe)) {
- /* only check (and later claim) if not already claimed */
- if (urb_priv->bandwidth == 0) {
- bustime = crisv10_usb_check_bandwidth(urb->dev, urb);
- if (bustime < 0) {
- tc_err("Not enough periodic bandwidth\n");
- urb_priv_free(hcd, urb);
- DBFEXIT;
- return -ENOSPC;
- }
- }
- }
-
- tc_dbg("Enqueue URB:0x%x[%d] epid:%d (%s) bufflen:%d\n",
- (unsigned int)urb, urb_priv->urb_num, epid,
- pipe_to_str(urb->pipe), urb->transfer_buffer_length);
-
- /* Create and link SBs required for this URB */
- retval = create_sb_for_urb(urb, mem_flags);
- if(retval != 0) {
- tc_err("Failed to create SBs for URB:0x%x[%d]\n", (unsigned int)urb,
- urb_priv->urb_num);
- urb_priv_free(hcd, urb);
- DBFEXIT;
- return retval;
- }
-
- /* Init intr EP pool if this URB is a INTR transfer. This pool is later
- used when inserting EPs in the TxIntrEPList. We do the alloc here
- so we can't run out of memory later */
- if(usb_pipeint(urb->pipe)) {
- retval = init_intr_urb(urb, mem_flags);
- if(retval != 0) {
- tc_warn("Failed to init Intr URB\n");
- urb_priv_free(hcd, urb);
- DBFEXIT;
- return retval;
- }
- }
-
- /* Disable other access when inserting USB */
- local_irq_save(flags);
-
- /* Claim bandwidth, if needed */
- if(bustime) {
- crisv10_usb_claim_bandwidth(urb->dev,
- urb,
- bustime,
- (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS));
- }
-
- /* Add URB to EP queue */
- urb_list_add(urb, epid, mem_flags);
-
- if(usb_pipeisoc(urb->pipe)) {
- /* Special processing of Isoc URBs. */
- tc_dma_process_isoc_urb(urb);
- } else {
- /* Process EP queue for rest of the URB types (Bulk, Ctrl, Intr) */
- tc_dma_process_queue(epid);
- }
-
- local_irq_restore(flags);
-
- DBFEXIT;
- return 0;
-}
-
-/* remove an URB from the transfer controller queues (called from hcd_driver)*/
-static int tc_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) {
- struct crisv10_urb_priv *urb_priv;
- unsigned long flags;
- int epid;
-
- DBFENTER;
- /* Disable interrupts here since a descriptor interrupt for the isoc epid
- will modify the sb list. This could possibly be done more granular, but
- urb_dequeue should not be used frequently anyway.
- */
- local_irq_save(flags);
-
- urb->status = status;
- urb_priv = urb->hcpriv;
-
- if (!urb_priv) {
- /* This happens if a device driver calls unlink on an urb that
- was never submitted (lazy driver) or if the urb was completed
- while dequeue was being called. */
- tc_warn("Dequeing of not enqueued URB:0x%x\n", (unsigned int)urb);
- local_irq_restore(flags);
- return 0;
- }
- epid = urb_priv->epid;
-
- tc_warn("Dequeing %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n",
- (urb == activeUrbList[epid]) ? "active" : "queued",
- (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
- str_type(urb->pipe), epid, urb->status,
- (urb_priv->later_data) ? "later-sched" : "");
-
- /* For Bulk, Ctrl and Intr are only one URB active at a time. So any URB
- that isn't active can be dequeued by just removing it from the queue */
- if(usb_pipebulk(urb->pipe) || usb_pipecontrol(urb->pipe) ||
- usb_pipeint(urb->pipe)) {
-
- /* Check if URB haven't gone further than the queue */
- if(urb != activeUrbList[epid]) {
- ASSERT(urb_priv->later_data == NULL);
- tc_warn("Dequeing URB:0x%x[%d] (%s %s epid:%d) from queue"
- " (not active)\n", (unsigned int)urb, urb_priv->urb_num,
- str_dir(urb->pipe), str_type(urb->pipe), epid);
-
- /* Finish the URB with error status from USB core */
- tc_finish_urb(hcd, urb, urb->status);
- local_irq_restore(flags);
- return 0;
- }
- }
-
- /* Set URB status to Unlink for handling when interrupt comes. */
- urb_priv->urb_state = UNLINK;
-
- /* Differentiate dequeing of Bulk and Ctrl from Isoc and Intr */
- switch(usb_pipetype(urb->pipe)) {
- case PIPE_BULK:
- /* Check if EP still is enabled */
- if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- /* The EP was enabled, disable it. */
- TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
- }
- /* Kicking dummy list out of the party. */
- TxBulkEPList[epid].next = virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]);
- break;
- case PIPE_CONTROL:
- /* Check if EP still is enabled */
- if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- /* The EP was enabled, disable it. */
- TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
- }
- break;
- case PIPE_ISOCHRONOUS:
- /* Disabling, busy-wait and unlinking of Isoc SBs will be done in
- finish_isoc_urb(). Because there might the case when URB is dequeued
- but there are other valid URBs waiting */
-
- /* Check if In Isoc EP still is enabled */
- if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- /* The EP was enabled, disable it. */
- TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
- }
- break;
- case PIPE_INTERRUPT:
- /* Special care is taken for interrupt URBs. EPs are unlinked in
- tc_finish_urb */
- break;
- default:
- break;
- }
-
- /* Asynchronous unlink, finish the URB later from scheduled or other
- event (data finished, error) */
- tc_finish_urb_later(hcd, urb, urb->status);
-
- local_irq_restore(flags);
- DBFEXIT;
- return 0;
-}
-
-
-static void tc_sync_finish_epid(struct usb_hcd *hcd, int epid) {
- volatile int timeout = 10000;
- struct urb* urb;
- struct crisv10_urb_priv* urb_priv;
- unsigned long flags;
-
- volatile struct USB_EP_Desc *first_ep; /* First EP in the list. */
- volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */
- volatile struct USB_EP_Desc *next_ep; /* The EP after current. */
-
- int type = epid_state[epid].type;
-
- /* Setting this flag will cause enqueue() to return -ENOENT for new
- submitions on this endpoint and finish_urb() wont process queue further */
- epid_state[epid].disabled = 1;
-
- switch(type) {
- case PIPE_BULK:
- /* Check if EP still is enabled */
- if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- /* The EP was enabled, disable it. */
- TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
- tc_warn("sync_finish: Disabling EP for epid:%d\n", epid);
-
- /* Do busy-wait until DMA not using this EP descriptor anymore */
- while((*R_DMA_CH8_SUB0_EP ==
- virt_to_phys(&TxBulkEPList[epid])) &&
- (timeout-- > 0));
-
- }
- break;
-
- case PIPE_CONTROL:
- /* Check if EP still is enabled */
- if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- /* The EP was enabled, disable it. */
- TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
- tc_warn("sync_finish: Disabling EP for epid:%d\n", epid);
-
- /* Do busy-wait until DMA not using this EP descriptor anymore */
- while((*R_DMA_CH8_SUB1_EP ==
- virt_to_phys(&TxCtrlEPList[epid])) &&
- (timeout-- > 0));
- }
- break;
-
- case PIPE_INTERRUPT:
- local_irq_save(flags);
- /* Disable all Intr EPs belonging to epid */
- first_ep = &TxIntrEPList[0];
- curr_ep = first_ep;
- do {
- next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
- if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) {
- /* Disable EP */
- next_ep->command &= ~IO_MASK(USB_EP_command, enable);
- }
- curr_ep = phys_to_virt(curr_ep->next);
- } while (curr_ep != first_ep);
-
- local_irq_restore(flags);
- break;
-
- case PIPE_ISOCHRONOUS:
- /* Check if EP still is enabled */
- if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- tc_warn("sync_finish: Disabling Isoc EP for epid:%d\n", epid);
- /* The EP was enabled, disable it. */
- TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-
- while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) &&
- (timeout-- > 0));
- }
- break;
- }
-
- local_irq_save(flags);
-
- /* Finish if there is active URB for this endpoint */
- if(activeUrbList[epid] != NULL) {
- urb = activeUrbList[epid];
- urb_priv = urb->hcpriv;
- ASSERT(urb_priv);
- tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n",
- (urb == activeUrbList[epid]) ? "active" : "queued",
- (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
- str_type(urb->pipe), epid, urb->status,
- (urb_priv->later_data) ? "later-sched" : "");
-
- tc_finish_urb(hcd, activeUrbList[epid], -ENOENT);
- ASSERT(activeUrbList[epid] == NULL);
- }
-
- /* Finish any queued URBs for this endpoint. There won't be any resubmitions
- because epid_disabled causes enqueue() to fail for this endpoint */
- while((urb = urb_list_first(epid)) != NULL) {
- urb_priv = urb->hcpriv;
- ASSERT(urb_priv);
-
- tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n",
- (urb == activeUrbList[epid]) ? "active" : "queued",
- (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
- str_type(urb->pipe), epid, urb->status,
- (urb_priv->later_data) ? "later-sched" : "");
-
- tc_finish_urb(hcd, urb, -ENOENT);
- }
- epid_state[epid].disabled = 0;
- local_irq_restore(flags);
-}
-
-/* free resources associated with an endpoint (called from hcd_driver) */
-static void tc_endpoint_disable(struct usb_hcd *hcd,
- struct usb_host_endpoint *ep) {
- DBFENTER;
- /* Only free epid if it has been allocated. We get two endpoint_disable
- requests for ctrl endpoints so ignore the second one */
- if(ep->hcpriv != NULL) {
- struct crisv10_ep_priv *ep_priv = ep->hcpriv;
- int epid = ep_priv->epid;
- tc_warn("endpoint_disable ep:0x%x ep-priv:0x%x (%s) (epid:%d freed)\n",
- (unsigned int)ep, (unsigned int)ep->hcpriv,
- endpoint_to_str(&(ep->desc)), epid);
-
- tc_sync_finish_epid(hcd, epid);
-
- ASSERT(activeUrbList[epid] == NULL);
- ASSERT(list_empty(&urb_list[epid]));
-
- tc_free_epid(ep);
- } else {
- tc_dbg("endpoint_disable ep:0x%x ep-priv:0x%x (%s)\n", (unsigned int)ep,
- (unsigned int)ep->hcpriv, endpoint_to_str(&(ep->desc)));
- }
- DBFEXIT;
-}
-
-static void tc_finish_urb_later_proc(struct work_struct* work) {
- unsigned long flags;
- struct urb_later_data* uld;
-
- local_irq_save(flags);
- uld = container_of(work, struct urb_later_data, dws.work);
- if(uld->urb == NULL) {
- late_dbg("Later finish of URB = NULL (allready finished)\n");
- } else {
- struct crisv10_urb_priv* urb_priv = uld->urb->hcpriv;
- ASSERT(urb_priv);
- if(urb_priv->urb_num == uld->urb_num) {
- late_dbg("Later finish of URB:0x%x[%d]\n", (unsigned int)(uld->urb),
- urb_priv->urb_num);
- if(uld->status != uld->urb->status) {
- errno_dbg("Later-finish URB with status:%d, later-status:%d\n",
- uld->urb->status, uld->status);
- }
- if(uld != urb_priv->later_data) {
- panic("Scheduled uld not same as URBs uld\n");
- }
- tc_finish_urb(uld->hcd, uld->urb, uld->status);
- } else {
- late_warn("Ignoring later finish of URB:0x%x[%d]"
- ", urb_num doesn't match current URB:0x%x[%d]",
- (unsigned int)(uld->urb), uld->urb_num,
- (unsigned int)(uld->urb), urb_priv->urb_num);
- }
- }
- local_irq_restore(flags);
- kmem_cache_free(later_data_cache, uld);
-}
-
-static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb,
- int status) {
- struct crisv10_urb_priv *urb_priv = urb->hcpriv;
- struct urb_later_data* uld;
-
- ASSERT(urb_priv);
-
- if(urb_priv->later_data != NULL) {
- /* Later-finish allready scheduled for this URB, just update status to
- return when finishing later */
- errno_dbg("Later-finish schedule change URB status:%d with new"
- " status:%d\n", urb_priv->later_data->status, status);
-
- urb_priv->later_data->status = status;
- return;
- }
-
- uld = kmem_cache_alloc(later_data_cache, GFP_ATOMIC);
- ASSERT(uld);
-
- uld->hcd = hcd;
- uld->urb = urb;
- uld->urb_num = urb_priv->urb_num;
- uld->status = status;
-
- INIT_DELAYED_WORK(&uld->dws, tc_finish_urb_later_proc);
- urb_priv->later_data = uld;
-
- /* Schedule the finishing of the URB to happen later */
- schedule_delayed_work(&uld->dws, LATER_TIMER_DELAY);
-}
-
-static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb,
- int status);
-
-static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status) {
- struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd);
- struct crisv10_urb_priv *urb_priv = urb->hcpriv;
- int epid;
- char toggle;
- int urb_num;
-
- DBFENTER;
- ASSERT(urb_priv != NULL);
- epid = urb_priv->epid;
- urb_num = urb_priv->urb_num;
-
- if(urb != activeUrbList[epid]) {
- if(urb_list_entry(urb, epid)) {
- /* Remove this URB from the list. Only happens when URB are finished
- before having been processed (dequeing) */
- urb_list_del(urb, epid);
- } else {
- tc_warn("Finishing of URB:0x%x[%d] neither active or in queue for"
- " epid:%d\n", (unsigned int)urb, urb_num, epid);
- }
- }
-
- /* Cancel any pending later-finish of this URB */
- if(urb_priv->later_data) {
- urb_priv->later_data->urb = NULL;
- }
-
- /* For an IN pipe, we always set the actual length, regardless of whether
- there was an error or not (which means the device driver can use the data
- if it wants to). */
- if(usb_pipein(urb->pipe)) {
- urb->actual_length = urb_priv->rx_offset;
- } else {
- /* Set actual_length for OUT urbs also; the USB mass storage driver seems
- to want that. */
- if (status == 0 && urb->status == -EINPROGRESS) {
- urb->actual_length = urb->transfer_buffer_length;
- } else {
- /* We wouldn't know of any partial writes if there was an error. */
- urb->actual_length = 0;
- }
- }
-
-
- /* URB status mangling */
- if(urb->status == -EINPROGRESS) {
- /* The USB core hasn't changed the status, let's set our finish status */
- urb->status = status;
-
- if ((status == 0) && (urb->transfer_flags & URB_SHORT_NOT_OK) &&
- usb_pipein(urb->pipe) &&
- (urb->actual_length != urb->transfer_buffer_length)) {
- /* URB_SHORT_NOT_OK means that short reads (shorter than the endpoint's
- max length) is to be treated as an error. */
- errno_dbg("Finishing URB:0x%x[%d] with SHORT_NOT_OK flag and short"
- " data:%d\n", (unsigned int)urb, urb_num,
- urb->actual_length);
- urb->status = -EREMOTEIO;
- }
-
- if(urb_priv->urb_state == UNLINK) {
- /* URB has been requested to be unlinked asynchronously */
- urb->status = -ECONNRESET;
- errno_dbg("Fixing unlink status of URB:0x%x[%d] to:%d\n",
- (unsigned int)urb, urb_num, urb->status);
- }
- } else {
- /* The USB Core wants to signal some error via the URB, pass it through */
- }
-
- /* use completely different finish function for Isoc URBs */
- if(usb_pipeisoc(urb->pipe)) {
- tc_finish_isoc_urb(hcd, urb, status);
- return;
- }
-
- /* Do special unlinking of EPs for Intr traffic */
- if(usb_pipeint(urb->pipe)) {
- tc_dma_unlink_intr_urb(urb);
- }
-
- /* Release allocated bandwidth for periodic transfers */
- if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe))
- crisv10_usb_release_bandwidth(hcd,
- usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS,
- urb_priv->bandwidth);
-
- /* This URB is active on EP */
- if(urb == activeUrbList[epid]) {
- /* We need to fiddle with the toggle bits because the hardware doesn't do
- it for us. */
- toggle = etrax_epid_get_toggle(epid, usb_pipeout(urb->pipe));
- usb_settoggle(urb->dev, usb_pipeendpoint(urb->pipe),
- usb_pipeout(urb->pipe), toggle);
-
- /* Checks for Ctrl and Bulk EPs */
- switch(usb_pipetype(urb->pipe)) {
- case PIPE_BULK:
- /* Check so Bulk EP realy is disabled before finishing active URB */
- ASSERT((TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) ==
- IO_STATE(USB_EP_command, enable, no));
- /* Disable sub-pointer for EP to avoid next tx_interrupt() to
- process Bulk EP. */
- TxBulkEPList[epid].sub = 0;
- /* No need to wait for the DMA before changing the next pointer.
- The modulo NBR_OF_EPIDS isn't actually necessary, since we will never use
- the last one (INVALID_EPID) for actual traffic. */
- TxBulkEPList[epid].next =
- virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]);
- break;
- case PIPE_CONTROL:
- /* Check so Ctrl EP realy is disabled before finishing active URB */
- ASSERT((TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) ==
- IO_STATE(USB_EP_command, enable, no));
- /* Disable sub-pointer for EP to avoid next tx_interrupt() to
- process Ctrl EP. */
- TxCtrlEPList[epid].sub = 0;
- break;
- }
- }
-
- /* Free HC-private URB data*/
- urb_priv_free(hcd, urb);
-
- if(urb->status) {
- errno_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n",
- (unsigned int)urb, urb_num, str_dir(urb->pipe),
- str_type(urb->pipe), urb->actual_length, urb->status);
- } else {
- tc_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n",
- (unsigned int)urb, urb_num, str_dir(urb->pipe),
- str_type(urb->pipe), urb->actual_length, urb->status);
- }
-
- /* If we just finished an active URB, clear active pointer. */
- if (urb == activeUrbList[epid]) {
- /* Make URB not active on EP anymore */
- activeUrbList[epid] = NULL;
-
- if(urb->status == 0) {
- /* URB finished sucessfully, process queue to see if there are any more
- URBs waiting before we call completion function.*/
- if(crisv10_hcd->running) {
- /* Only process queue if USB controller is running */
- tc_dma_process_queue(epid);
- } else {
- tc_warn("No processing of queue for epid:%d, USB Controller not"
- " running\n", epid);
- }
- }
- }
-
- /* Hand the URB from HCD to its USB device driver, using its completion
- functions */
- usb_hcd_giveback_urb (hcd, urb, status);
-
- /* Check the queue once more if the URB returned with error, because we
- didn't do it before the completion function because the specification
- states that the queue should not restart until all it's unlinked
- URBs have been fully retired, with the completion functions run */
- if(crisv10_hcd->running) {
- /* Only process queue if USB controller is running */
- tc_dma_process_queue(epid);
- } else {
- tc_warn("No processing of queue for epid:%d, USB Controller not running\n",
- epid);
- }
-
- DBFEXIT;
-}
-
-static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb,
- int status) {
- struct crisv10_urb_priv *urb_priv = urb->hcpriv;
- int epid, i;
- volatile int timeout = 10000;
- int bandwidth = 0;
-
- ASSERT(urb_priv);
- epid = urb_priv->epid;
-
- ASSERT(usb_pipeisoc(urb->pipe));
-
- /* Set that all isoc packets have status and length set before
- completing the urb. */
- for (i = urb_priv->isoc_packet_counter; i < urb->number_of_packets; i++){
- urb->iso_frame_desc[i].actual_length = 0;
- urb->iso_frame_desc[i].status = -EPROTO;
- }
-
- /* Check if the URB is currently active (done or error) */
- if(urb == activeUrbList[epid]) {
- /* Check if there are another In Isoc URB queued for this epid */
- if (!list_empty(&urb_list[epid])&& !epid_state[epid].disabled) {
- /* Move it from queue to active and mark it started so Isoc transfers
- won't be interrupted.
- All Isoc URBs data transfers are already added to DMA lists so we
- don't have to insert anything in DMA lists here. */
- activeUrbList[epid] = urb_list_first(epid);
- ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_state =
- STARTED;
- urb_list_del(activeUrbList[epid], epid);
-
- if(urb->status) {
- errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)"
- " status:%d, new waiting URB:0x%x[%d]\n",
- (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
- str_type(urb->pipe), urb_priv->isoc_packet_counter,
- urb->number_of_packets, urb->status,
- (unsigned int)activeUrbList[epid],
- ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_num);
- }
-
- } else { /* No other URB queued for this epid */
- if(urb->status) {
- errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)"
- " status:%d, no new URB waiting\n",
- (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe),
- str_type(urb->pipe), urb_priv->isoc_packet_counter,
- urb->number_of_packets, urb->status);
- }
-
- /* Check if EP is still enabled, then shut it down. */
- if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- isoc_dbg("Isoc EP enabled for epid:%d, disabling it\n", epid);
-
- /* Should only occur for In Isoc EPs where SB isn't consumed. */
- ASSERT(usb_pipein(urb->pipe));
-
- /* Disable it and wait for it to stop */
- TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable);
-
- /* Ah, the luxury of busy-wait. */
- while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) &&
- (timeout-- > 0));
- }
-
- /* Unlink SB to say that epid is finished. */
- TxIsocEPList[epid].sub = 0;
- TxIsocEPList[epid].hw_len = 0;
-
- /* No URB active for EP anymore */
- activeUrbList[epid] = NULL;
- }
- } else { /* Finishing of not active URB (queued up with SBs thought) */
- isoc_warn("finish_isoc_urb (URB:0x%x %s) (%d of %d packets) status:%d,"
- " SB queued but not active\n",
- (unsigned int)urb, str_dir(urb->pipe),
- urb_priv->isoc_packet_counter, urb->number_of_packets,
- urb->status);
- if(usb_pipeout(urb->pipe)) {
- /* Finishing of not yet active Out Isoc URB needs unlinking of SBs. */
- struct USB_SB_Desc *iter_sb, *prev_sb, *next_sb;
-
- iter_sb = TxIsocEPList[epid].sub ?
- phys_to_virt(TxIsocEPList[epid].sub) : 0;
- prev_sb = 0;
-
- /* SB that is linked before this URBs first SB */
- while (iter_sb && (iter_sb != urb_priv->first_sb)) {
- prev_sb = iter_sb;
- iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0;
- }
-
- if (iter_sb == 0) {
- /* Unlink of the URB currently being transmitted. */
- prev_sb = 0;
- iter_sb = TxIsocEPList[epid].sub ? phys_to_virt(TxIsocEPList[epid].sub) : 0;
- }
-
- while (iter_sb && (iter_sb != urb_priv->last_sb)) {
- iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0;
- }
-
- if (iter_sb) {
- next_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0;
- } else {
- /* This should only happen if the DMA has completed
- processing the SB list for this EP while interrupts
- are disabled. */
- isoc_dbg("Isoc urb not found, already sent?\n");
- next_sb = 0;
- }
- if (prev_sb) {
- prev_sb->next = next_sb ? virt_to_phys(next_sb) : 0;
- } else {
- TxIsocEPList[epid].sub = next_sb ? virt_to_phys(next_sb) : 0;
- }
- }
- }
-
- /* Free HC-private URB data*/
- bandwidth = urb_priv->bandwidth;
- urb_priv_free(hcd, urb);
-
- crisv10_usb_release_bandwidth(hcd, usb_pipeisoc(urb->pipe), bandwidth);
-
- /* Hand the URB from HCD to its USB device driver, using its completion
- functions */
- usb_hcd_giveback_urb (hcd, urb, status);
-}
-
-static __u32 urb_num = 0;
-
-/* allocate and initialize URB private data */
-static int urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid,
- int mem_flags) {
- struct crisv10_urb_priv *urb_priv;
-
- urb_priv = kmalloc(sizeof *urb_priv, mem_flags);
- if (!urb_priv)
- return -ENOMEM;
- memset(urb_priv, 0, sizeof *urb_priv);
-
- urb_priv->epid = epid;
- urb_priv->urb_state = NOT_STARTED;
-
- urb->hcpriv = urb_priv;
- /* Assign URB a sequence number, and increment counter */
- urb_priv->urb_num = urb_num;
- urb_num++;
- urb_priv->bandwidth = 0;
- return 0;
-}
-
-/* free URB private data */
-static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb) {
- int i;
- struct crisv10_urb_priv *urb_priv = urb->hcpriv;
- ASSERT(urb_priv != 0);
-
- /* Check it has any SBs linked that needs to be freed*/
- if(urb_priv->first_sb != NULL) {
- struct USB_SB_Desc *next_sb, *first_sb, *last_sb;
- int i = 0;
- first_sb = urb_priv->first_sb;
- last_sb = urb_priv->last_sb;
- ASSERT(last_sb);
- while(first_sb != last_sb) {
- next_sb = (struct USB_SB_Desc *)phys_to_virt(first_sb->next);
- kmem_cache_free(usb_desc_cache, first_sb);
- first_sb = next_sb;
- i++;
- }
- kmem_cache_free(usb_desc_cache, last_sb);
- i++;
- }
-
- /* Check if it has any EPs in its Intr pool that also needs to be freed */
- if(urb_priv->intr_ep_pool_length > 0) {
- for(i = 0; i < urb_priv->intr_ep_pool_length; i++) {
- kfree(urb_priv->intr_ep_pool[i]);
- }
- /*
- tc_dbg("Freed %d EPs from URB:0x%x EP pool\n",
- urb_priv->intr_ep_pool_length, (unsigned int)urb);
- */
- }
-
- kfree(urb_priv);
- urb->hcpriv = NULL;
-}
-
-static int ep_priv_create(struct usb_host_endpoint *ep, int mem_flags) {
- struct crisv10_ep_priv *ep_priv;
-
- ep_priv = kmalloc(sizeof *ep_priv, mem_flags);
- if (!ep_priv)
- return -ENOMEM;
- memset(ep_priv, 0, sizeof *ep_priv);
-
- ep->hcpriv = ep_priv;
- return 0;
-}
-
-static void ep_priv_free(struct usb_host_endpoint *ep) {
- struct crisv10_ep_priv *ep_priv = ep->hcpriv;
- ASSERT(ep_priv);
- kfree(ep_priv);
- ep->hcpriv = NULL;
-}
-
-/*
- * usb_check_bandwidth():
- *
- * old_alloc is from host_controller->bandwidth_allocated in microseconds;
- * bustime is from calc_bus_time(), but converted to microseconds.
- *
- * returns <bustime in us> if successful,
- * or -ENOSPC if bandwidth request fails.
- *
- * FIXME:
- * This initial implementation does not use Endpoint.bInterval
- * in managing bandwidth allocation.
- * It probably needs to be expanded to use Endpoint.bInterval.
- * This can be done as a later enhancement (correction).
- *
- * This will also probably require some kind of
- * frame allocation tracking...meaning, for example,
- * that if multiple drivers request interrupts every 10 USB frames,
- * they don't all have to be allocated at
- * frame numbers N, N+10, N+20, etc. Some of them could be at
- * N+11, N+21, N+31, etc., and others at
- * N+12, N+22, N+32, etc.
- *
- * Similarly for isochronous transfers...
- *
- * Individual HCDs can schedule more directly ... this logic
- * is not correct for high speed transfers.
- */
-static int crisv10_usb_check_bandwidth(
- struct usb_device *dev,
- struct urb *urb)
-{
- unsigned int pipe = urb->pipe;
- long bustime;
- int is_in = usb_pipein (pipe);
- int is_iso = usb_pipeisoc (pipe);
- int old_alloc = dev->bus->bandwidth_allocated;
- int new_alloc;
-
- bustime = NS_TO_US (usb_calc_bus_time (dev->speed, is_in, is_iso,
- usb_maxpacket (dev, pipe, !is_in)));
- if (is_iso)
- bustime /= urb->number_of_packets;
-
- new_alloc = old_alloc + (int) bustime;
- if (new_alloc > FRAME_TIME_MAX_USECS_ALLOC) {
- dev_dbg (&dev->dev, "usb_check_bandwidth FAILED: %d + %ld = %d usec\n",
- old_alloc, bustime, new_alloc);
- bustime = -ENOSPC; /* report error */
- }
-
- return bustime;
-}
-
-/**
- * usb_claim_bandwidth - records bandwidth for a periodic transfer
- * @dev: source/target of request
- * @urb: request (urb->dev == dev)
- * @bustime: bandwidth consumed, in (average) microseconds per frame
- * @isoc: true iff the request is isochronous
- *
- * HCDs are expected not to overcommit periodic bandwidth, and to record such
- * reservations whenever endpoints are added to the periodic schedule.
- *
- * FIXME averaging per-frame is suboptimal. Better to sum over the HCD's
- * entire periodic schedule ... 32 frames for OHCI, 1024 for UHCI, settable
- * for EHCI (256/512/1024 frames, default 1024) and have the bus expose how
- * large its periodic schedule is.
- */
-static void crisv10_usb_claim_bandwidth(
- struct usb_device *dev,
- struct urb *urb, int bustime, int isoc)
-{
- dev->bus->bandwidth_allocated += bustime;
- if (isoc)
- dev->bus->bandwidth_isoc_reqs++;
- else
- dev->bus->bandwidth_int_reqs++;
- struct crisv10_urb_priv *urb_priv;
- urb_priv = urb->hcpriv;
- urb_priv->bandwidth = bustime;
-}
-
-/**
- * usb_release_bandwidth - reverses effect of usb_claim_bandwidth()
- * @hcd: host controller
- * @isoc: true iff the request is isochronous
- * @bandwidth: bandwidth returned
- *
- * This records that previously allocated bandwidth has been released.
- * Bandwidth is released when endpoints are removed from the host controller's
- * periodic schedule.
- */
-static void crisv10_usb_release_bandwidth(
- struct usb_hcd *hcd,
- int isoc,
- int bandwidth)
-{
- hcd_to_bus(hcd)->bandwidth_allocated -= bandwidth;
- if (isoc)
- hcd_to_bus(hcd)->bandwidth_isoc_reqs--;
- else
- hcd_to_bus(hcd)->bandwidth_int_reqs--;
-}
-
-
-/* EPID handling functions, managing EP-list in Etrax through wrappers */
-/* ------------------------------------------------------------------- */
-
-/* Sets up a new EPID for an endpoint or returns existing if found */
-static int tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb,
- int mem_flags) {
- int epid;
- char devnum, endpoint, out_traffic, slow;
- int maxlen;
- __u32 epid_data;
- struct crisv10_ep_priv *ep_priv = ep->hcpriv;
-
- DBFENTER;
-
- /* Check if a valid epid already is setup for this endpoint */
- if(ep_priv != NULL) {
- return ep_priv->epid;
- }
-
- /* We must find and initiate a new epid for this urb. */
- epid = tc_allocate_epid();
-
- if (epid == -1) {
- /* Failed to allocate a new epid. */
- DBFEXIT;
- return epid;
- }
-
- /* We now have a new epid to use. Claim it. */
- epid_state[epid].inuse = 1;
-
- /* Init private data for new endpoint */
- if(ep_priv_create(ep, mem_flags) != 0) {
- return -ENOMEM;
- }
- ep_priv = ep->hcpriv;
- ep_priv->epid = epid;
-
- devnum = usb_pipedevice(urb->pipe);
- endpoint = usb_pipeendpoint(urb->pipe);
- slow = (urb->dev->speed == USB_SPEED_LOW);
- maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe));
-
- if (usb_pipetype(urb->pipe) == PIPE_CONTROL) {
- /* We want both IN and OUT control traffic to be put on the same
- EP/SB list. */
- out_traffic = 1;
- } else {
- out_traffic = usb_pipeout(urb->pipe);
- }
-
- if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
- epid_data = IO_STATE(R_USB_EPT_DATA_ISO, valid, yes) |
- /* FIXME: Change any to the actual port? */
- IO_STATE(R_USB_EPT_DATA_ISO, port, any) |
- IO_FIELD(R_USB_EPT_DATA_ISO, max_len, maxlen) |
- IO_FIELD(R_USB_EPT_DATA_ISO, ep, endpoint) |
- IO_FIELD(R_USB_EPT_DATA_ISO, dev, devnum);
- etrax_epid_iso_set(epid, epid_data);
- } else {
- epid_data = IO_STATE(R_USB_EPT_DATA, valid, yes) |
- IO_FIELD(R_USB_EPT_DATA, low_speed, slow) |
- /* FIXME: Change any to the actual port? */
- IO_STATE(R_USB_EPT_DATA, port, any) |
- IO_FIELD(R_USB_EPT_DATA, max_len, maxlen) |
- IO_FIELD(R_USB_EPT_DATA, ep, endpoint) |
- IO_FIELD(R_USB_EPT_DATA, dev, devnum);
- etrax_epid_set(epid, epid_data);
- }
-
- epid_state[epid].out_traffic = out_traffic;
- epid_state[epid].type = usb_pipetype(urb->pipe);
-
- tc_warn("Setting up ep:0x%x epid:%d (addr:%d endp:%d max_len:%d %s %s %s)\n",
- (unsigned int)ep, epid, devnum, endpoint, maxlen,
- str_type(urb->pipe), out_traffic ? "out" : "in",
- slow ? "low" : "full");
-
- /* Enable Isoc eof interrupt if we set up the first Isoc epid */
- if(usb_pipeisoc(urb->pipe)) {
- isoc_epid_counter++;
- if(isoc_epid_counter == 1) {
- isoc_warn("Enabled Isoc eof interrupt\n");
- *R_USB_IRQ_MASK_SET = IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set);
- }
- }
-
- DBFEXIT;
- return epid;
-}
-
-static void tc_free_epid(struct usb_host_endpoint *ep) {
- unsigned long flags;
- struct crisv10_ep_priv *ep_priv = ep->hcpriv;
- int epid;
- volatile int timeout = 10000;
-
- DBFENTER;
-
- if (ep_priv == NULL) {
- tc_warn("Trying to free unused epid on ep:0x%x\n", (unsigned int)ep);
- DBFEXIT;
- return;
- }
-
- epid = ep_priv->epid;
-
- /* Disable Isoc eof interrupt if we free the last Isoc epid */
- if(epid_isoc(epid)) {
- ASSERT(isoc_epid_counter > 0);
- isoc_epid_counter--;
- if(isoc_epid_counter == 0) {
- *R_USB_IRQ_MASK_CLR = IO_STATE(R_USB_IRQ_MASK_CLR, iso_eof, clr);
- isoc_warn("Disabled Isoc eof interrupt\n");
- }
- }
-
- /* Take lock manualy instead of in epid_x_x wrappers,
- because we need to be polling here */
- spin_lock_irqsave(&etrax_epid_lock, flags);
-
- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid);
- nop();
- while((*R_USB_EPT_DATA & IO_MASK(R_USB_EPT_DATA, hold)) &&
- (timeout-- > 0));
- /* This will, among other things, set the valid field to 0. */
- *R_USB_EPT_DATA = 0;
- spin_unlock_irqrestore(&etrax_epid_lock, flags);
-
- /* Free resource in software state info list */
- epid_state[epid].inuse = 0;
-
- /* Free private endpoint data */
- ep_priv_free(ep);
-
- DBFEXIT;
-}
-
-static int tc_allocate_epid(void) {
- int i;
- DBFENTER;
- for (i = 0; i < NBR_OF_EPIDS; i++) {
- if (!epid_inuse(i)) {
- DBFEXIT;
- return i;
- }
- }
-
- tc_warn("Found no free epids\n");
- DBFEXIT;
- return -1;
-}
-
-
-/* Wrappers around the list functions (include/linux/list.h). */
-/* ---------------------------------------------------------- */
-static inline int __urb_list_empty(int epid) {
- int retval;
- retval = list_empty(&urb_list[epid]);
- return retval;
-}
-
-/* Returns first urb for this epid, or NULL if list is empty. */
-static inline struct urb *urb_list_first(int epid) {
- unsigned long flags;
- struct urb *first_urb = 0;
- spin_lock_irqsave(&urb_list_lock, flags);
- if (!__urb_list_empty(epid)) {
- /* Get the first urb (i.e. head->next). */
- urb_entry_t *urb_entry = list_entry((&urb_list[epid])->next, urb_entry_t, list);
- first_urb = urb_entry->urb;
- }
- spin_unlock_irqrestore(&urb_list_lock, flags);
- return first_urb;
-}
-
-/* Adds an urb_entry last in the list for this epid. */
-static inline void urb_list_add(struct urb *urb, int epid, int mem_flags) {
- unsigned long flags;
- urb_entry_t *urb_entry = (urb_entry_t *)kmalloc(sizeof(urb_entry_t), mem_flags);
- ASSERT(urb_entry);
-
- urb_entry->urb = urb;
- spin_lock_irqsave(&urb_list_lock, flags);
- list_add_tail(&urb_entry->list, &urb_list[epid]);
- spin_unlock_irqrestore(&urb_list_lock, flags);
-}
-
-/* Search through the list for an element that contains this urb. (The list
- is expected to be short and the one we are about to delete will often be
- the first in the list.)
- Should be protected by spin_locks in calling function */
-static inline urb_entry_t *__urb_list_entry(struct urb *urb, int epid) {
- struct list_head *entry;
- struct list_head *tmp;
- urb_entry_t *urb_entry;
-
- list_for_each_safe(entry, tmp, &urb_list[epid]) {
- urb_entry = list_entry(entry, urb_entry_t, list);
- ASSERT(urb_entry);
- ASSERT(urb_entry->urb);
-
- if (urb_entry->urb == urb) {
- return urb_entry;
- }
- }
- return 0;
-}
-
-/* Same function as above but for global use. Protects list by spinlock */
-static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid) {
- unsigned long flags;
- urb_entry_t *urb_entry;
- spin_lock_irqsave(&urb_list_lock, flags);
- urb_entry = __urb_list_entry(urb, epid);
- spin_unlock_irqrestore(&urb_list_lock, flags);
- return (urb_entry);
-}
-
-/* Delete an urb from the list. */
-static inline void urb_list_del(struct urb *urb, int epid) {
- unsigned long flags;
- urb_entry_t *urb_entry;
-
- /* Delete entry and free. */
- spin_lock_irqsave(&urb_list_lock, flags);
- urb_entry = __urb_list_entry(urb, epid);
- ASSERT(urb_entry);
-
- list_del(&urb_entry->list);
- spin_unlock_irqrestore(&urb_list_lock, flags);
- kfree(urb_entry);
-}
-
-/* Move an urb to the end of the list. */
-static inline void urb_list_move_last(struct urb *urb, int epid) {
- unsigned long flags;
- urb_entry_t *urb_entry;
-
- spin_lock_irqsave(&urb_list_lock, flags);
- urb_entry = __urb_list_entry(urb, epid);
- ASSERT(urb_entry);
-
- list_del(&urb_entry->list);
- list_add_tail(&urb_entry->list, &urb_list[epid]);
- spin_unlock_irqrestore(&urb_list_lock, flags);
-}
-
-/* Get the next urb in the list. */
-static inline struct urb *urb_list_next(struct urb *urb, int epid) {
- unsigned long flags;
- urb_entry_t *urb_entry;
-
- spin_lock_irqsave(&urb_list_lock, flags);
- urb_entry = __urb_list_entry(urb, epid);
- ASSERT(urb_entry);
-
- if (urb_entry->list.next != &urb_list[epid]) {
- struct list_head *elem = urb_entry->list.next;
- urb_entry = list_entry(elem, urb_entry_t, list);
- spin_unlock_irqrestore(&urb_list_lock, flags);
- return urb_entry->urb;
- } else {
- spin_unlock_irqrestore(&urb_list_lock, flags);
- return NULL;
- }
-}
-
-struct USB_EP_Desc* create_ep(int epid, struct USB_SB_Desc* sb_desc,
- int mem_flags) {
- struct USB_EP_Desc *ep_desc;
- ep_desc = (struct USB_EP_Desc *) kmem_cache_alloc(usb_desc_cache, mem_flags);
- if(ep_desc == NULL)
- return NULL;
- memset(ep_desc, 0, sizeof(struct USB_EP_Desc));
-
- ep_desc->hw_len = 0;
- ep_desc->command = (IO_FIELD(USB_EP_command, epid, epid) |
- IO_STATE(USB_EP_command, enable, yes));
- if(sb_desc == NULL) {
- ep_desc->sub = 0;
- } else {
- ep_desc->sub = virt_to_phys(sb_desc);
- }
- return ep_desc;
-}
-
-#define TT_ZOUT 0
-#define TT_IN 1
-#define TT_OUT 2
-#define TT_SETUP 3
-
-#define CMD_EOL IO_STATE(USB_SB_command, eol, yes)
-#define CMD_INTR IO_STATE(USB_SB_command, intr, yes)
-#define CMD_FULL IO_STATE(USB_SB_command, full, yes)
-
-/* Allocation and setup of a generic SB. Used to create SETUP, OUT and ZOUT
- SBs. Also used by create_sb_in() to avoid same allocation procedure at two
- places */
-struct USB_SB_Desc* create_sb(struct USB_SB_Desc* sb_prev, int tt, void* data,
- int datalen, int mem_flags) {
- struct USB_SB_Desc *sb_desc;
- sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags);
- if(sb_desc == NULL)
- return NULL;
- memset(sb_desc, 0, sizeof(struct USB_SB_Desc));
-
- sb_desc->command = IO_FIELD(USB_SB_command, tt, tt) |
- IO_STATE(USB_SB_command, eot, yes);
-
- sb_desc->sw_len = datalen;
- if(data != NULL) {
- sb_desc->buf = virt_to_phys(data);
- } else {
- sb_desc->buf = 0;
- }
- if(sb_prev != NULL) {
- sb_prev->next = virt_to_phys(sb_desc);
- }
- return sb_desc;
-}
-
-/* Creates a copy of an existing SB by allocation space for it and copy
- settings */
-struct USB_SB_Desc* create_sb_copy(struct USB_SB_Desc* sb_orig, int mem_flags) {
- struct USB_SB_Desc *sb_desc;
- sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags);
- if(sb_desc == NULL)
- return NULL;
-
- memcpy(sb_desc, sb_orig, sizeof(struct USB_SB_Desc));
- return sb_desc;
-}
-
-/* A specific create_sb function for creation of in SBs. This is due to
- that datalen in In SBs shows how many packets we are expecting. It also
- sets up the rem field to show if how many bytes we expect in last packet
- if it's not a full one */
-struct USB_SB_Desc* create_sb_in(struct USB_SB_Desc* sb_prev, int datalen,
- int maxlen, int mem_flags) {
- struct USB_SB_Desc *sb_desc;
- sb_desc = create_sb(sb_prev, TT_IN, NULL,
- datalen ? (datalen - 1) / maxlen + 1 : 0, mem_flags);
- if(sb_desc == NULL)
- return NULL;
- sb_desc->command |= IO_FIELD(USB_SB_command, rem, datalen % maxlen);
- return sb_desc;
-}
-
-void set_sb_cmds(struct USB_SB_Desc *sb_desc, __u16 flags) {
- sb_desc->command |= flags;
-}
-
-int create_sb_for_urb(struct urb *urb, int mem_flags) {
- int is_out = !usb_pipein(urb->pipe);
- int type = usb_pipetype(urb->pipe);
- int maxlen = usb_maxpacket(urb->dev, urb->pipe, is_out);
- int buf_len = urb->transfer_buffer_length;
- void *buf = buf_len > 0 ? urb->transfer_buffer : NULL;
- struct USB_SB_Desc *sb_desc = NULL;
-
- struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv != NULL);
-
- switch(type) {
- case PIPE_CONTROL:
- /* Setup stage */
- sb_desc = create_sb(NULL, TT_SETUP, urb->setup_packet, 8, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- set_sb_cmds(sb_desc, CMD_FULL);
-
- /* Attach first SB to URB */
- urb_priv->first_sb = sb_desc;
-
- if (is_out) { /* Out Control URB */
- /* If this Control OUT transfer has an optional data stage we add
- an OUT token before the mandatory IN (status) token */
- if ((buf_len > 0) && buf) {
- sb_desc = create_sb(sb_desc, TT_OUT, buf, buf_len, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- set_sb_cmds(sb_desc, CMD_FULL);
- }
-
- /* Status stage */
- /* The data length has to be exactly 1. This is due to a requirement
- of the USB specification that a host must be prepared to receive
- data in the status phase */
- sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- } else { /* In control URB */
- /* Data stage */
- sb_desc = create_sb_in(sb_desc, buf_len, maxlen, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
-
- /* Status stage */
- /* Read comment at zout_buffer declaration for an explanation to this. */
- sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- /* Set descriptor interrupt flag for in URBs so we can finish URB after
- zout-packet has been sent */
- set_sb_cmds(sb_desc, CMD_INTR | CMD_FULL);
- }
- /* Set end-of-list flag in last SB */
- set_sb_cmds(sb_desc, CMD_EOL);
- /* Attach last SB to URB */
- urb_priv->last_sb = sb_desc;
- break;
-
- case PIPE_BULK:
- if (is_out) { /* Out Bulk URB */
- sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- /* The full field is set to yes, even if we don't actually check that
- this is a full-length transfer (i.e., that transfer_buffer_length %
- maxlen = 0).
- Setting full prevents the USB controller from sending an empty packet
- in that case. However, if URB_ZERO_PACKET was set we want that. */
- if (!(urb->transfer_flags & URB_ZERO_PACKET)) {
- set_sb_cmds(sb_desc, CMD_FULL);
- }
- } else { /* In Bulk URB */
- sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- }
- /* Set end-of-list flag for last SB */
- set_sb_cmds(sb_desc, CMD_EOL);
-
- /* Attach SB to URB */
- urb_priv->first_sb = sb_desc;
- urb_priv->last_sb = sb_desc;
- break;
-
- case PIPE_INTERRUPT:
- if(is_out) { /* Out Intr URB */
- sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
-
- /* The full field is set to yes, even if we don't actually check that
- this is a full-length transfer (i.e., that transfer_buffer_length %
- maxlen = 0).
- Setting full prevents the USB controller from sending an empty packet
- in that case. However, if URB_ZERO_PACKET was set we want that. */
- if (!(urb->transfer_flags & URB_ZERO_PACKET)) {
- set_sb_cmds(sb_desc, CMD_FULL);
- }
- /* Only generate TX interrupt if it's a Out URB*/
- set_sb_cmds(sb_desc, CMD_INTR);
-
- } else { /* In Intr URB */
- sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- }
- /* Set end-of-list flag for last SB */
- set_sb_cmds(sb_desc, CMD_EOL);
-
- /* Attach SB to URB */
- urb_priv->first_sb = sb_desc;
- urb_priv->last_sb = sb_desc;
-
- break;
- case PIPE_ISOCHRONOUS:
- if(is_out) { /* Out Isoc URB */
- int i;
- if(urb->number_of_packets == 0) {
- tc_err("Can't create SBs for Isoc URB with zero packets\n");
- return -EPIPE;
- }
- /* Create one SB descriptor for each packet and link them together. */
- for(i = 0; i < urb->number_of_packets; i++) {
- if (urb->iso_frame_desc[i].length > 0) {
-
- sb_desc = create_sb(sb_desc, TT_OUT, urb->transfer_buffer +
- urb->iso_frame_desc[i].offset,
- urb->iso_frame_desc[i].length, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
-
- /* Check if it's a full length packet */
- if (urb->iso_frame_desc[i].length ==
- usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe))) {
- set_sb_cmds(sb_desc, CMD_FULL);
- }
-
- } else { /* zero length packet */
- sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- set_sb_cmds(sb_desc, CMD_FULL);
- }
- /* Attach first SB descriptor to URB */
- if (i == 0) {
- urb_priv->first_sb = sb_desc;
- }
- }
- /* Set interrupt and end-of-list flags in last SB */
- set_sb_cmds(sb_desc, CMD_INTR | CMD_EOL);
- /* Attach last SB descriptor to URB */
- urb_priv->last_sb = sb_desc;
- tc_dbg("Created %d out SBs for Isoc URB:0x%x\n",
- urb->number_of_packets, (unsigned int)urb);
- } else { /* In Isoc URB */
- /* Actual number of packets is not relevant for periodic in traffic as
- long as it is more than zero. Set to 1 always. */
- sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags);
- if(sb_desc == NULL)
- return -ENOMEM;
- /* Set end-of-list flags for SB */
- set_sb_cmds(sb_desc, CMD_EOL);
-
- /* Attach SB to URB */
- urb_priv->first_sb = sb_desc;
- urb_priv->last_sb = sb_desc;
- }
- break;
- default:
- tc_err("Unknown pipe-type\n");
- return -EPIPE;
- break;
- }
- return 0;
-}
-
-int init_intr_urb(struct urb *urb, int mem_flags) {
- struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- struct USB_EP_Desc* ep_desc;
- int interval;
- int i;
- int ep_count;
-
- ASSERT(urb_priv != NULL);
- ASSERT(usb_pipeint(urb->pipe));
- /* We can't support interval longer than amount of eof descriptors in
- TxIntrEPList */
- if(urb->interval > MAX_INTR_INTERVAL) {
- tc_err("Interrupt interval %dms too big (max: %dms)\n", urb->interval,
- MAX_INTR_INTERVAL);
- return -EINVAL;
- }
-
- /* We assume that the SB descriptors already have been setup */
- ASSERT(urb_priv->first_sb != NULL);
-
- /* Round of the interval to 2^n, it is obvious that this code favours
- smaller numbers, but that is actually a good thing */
- /* FIXME: The "rounding error" for larger intervals will be quite
- large. For in traffic this shouldn't be a problem since it will only
- mean that we "poll" more often. */
- interval = urb->interval;
- for (i = 0; interval; i++) {
- interval = interval >> 1;
- }
- urb_priv->interval = 1 << (i - 1);
-
- /* We can only have max interval for Out Interrupt due to that we can only
- handle one linked in EP for a certain epid in the Intr descr array at the
- time. The USB Controller in the Etrax 100LX continues to process Intr EPs
- so we have no way of knowing which one that caused the actual transfer if
- we have several linked in. */
- if(usb_pipeout(urb->pipe)) {
- urb_priv->interval = MAX_INTR_INTERVAL;
- }
-
- /* Calculate amount of EPs needed */
- ep_count = MAX_INTR_INTERVAL / urb_priv->interval;
-
- for(i = 0; i < ep_count; i++) {
- ep_desc = create_ep(urb_priv->epid, urb_priv->first_sb, mem_flags);
- if(ep_desc == NULL) {
- /* Free any descriptors that we may have allocated before failure */
- while(i > 0) {
- i--;
- kfree(urb_priv->intr_ep_pool[i]);
- }
- return -ENOMEM;
- }
- urb_priv->intr_ep_pool[i] = ep_desc;
- }
- urb_priv->intr_ep_pool_length = ep_count;
- return 0;
-}
-
-/* DMA RX/TX functions */
-/* ----------------------- */
-
-static void tc_dma_init_rx_list(void) {
- int i;
-
- /* Setup descriptor list except last one */
- for (i = 0; i < (NBR_OF_RX_DESC - 1); i++) {
- RxDescList[i].sw_len = RX_DESC_BUF_SIZE;
- RxDescList[i].command = 0;
- RxDescList[i].next = virt_to_phys(&RxDescList[i + 1]);
- RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE));
- RxDescList[i].hw_len = 0;
- RxDescList[i].status = 0;
-
- /* DMA IN cache bug. (struct etrax_dma_descr has the same layout as
- USB_IN_Desc for the relevant fields.) */
- prepare_rx_descriptor((struct etrax_dma_descr*)&RxDescList[i]);
-
- }
- /* Special handling of last descriptor */
- RxDescList[i].sw_len = RX_DESC_BUF_SIZE;
- RxDescList[i].command = IO_STATE(USB_IN_command, eol, yes);
- RxDescList[i].next = virt_to_phys(&RxDescList[0]);
- RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE));
- RxDescList[i].hw_len = 0;
- RxDescList[i].status = 0;
-
- /* Setup list pointers that show progress in list */
- myNextRxDesc = &RxDescList[0];
- myLastRxDesc = &RxDescList[NBR_OF_RX_DESC - 1];
-
- flush_etrax_cache();
- /* Point DMA to first descriptor in list and start it */
- *R_DMA_CH9_FIRST = virt_to_phys(myNextRxDesc);
- *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, start);
-}
-
-
-static void tc_dma_init_tx_bulk_list(void) {
- int i;
- volatile struct USB_EP_Desc *epDescr;
-
- for (i = 0; i < (NBR_OF_EPIDS - 1); i++) {
- epDescr = &(TxBulkEPList[i]);
- CHECK_ALIGN(epDescr);
- epDescr->hw_len = 0;
- epDescr->command = IO_FIELD(USB_EP_command, epid, i);
- epDescr->sub = 0;
- epDescr->next = virt_to_phys(&TxBulkEPList[i + 1]);
-
- /* Initiate two EPs, disabled and with the eol flag set. No need for any
- preserved epid. */
-
- /* The first one has the intr flag set so we get an interrupt when the DMA
- channel is about to become disabled. */
- CHECK_ALIGN(&TxBulkDummyEPList[i][0]);
- TxBulkDummyEPList[i][0].hw_len = 0;
- TxBulkDummyEPList[i][0].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) |
- IO_STATE(USB_EP_command, eol, yes) |
- IO_STATE(USB_EP_command, intr, yes));
- TxBulkDummyEPList[i][0].sub = 0;
- TxBulkDummyEPList[i][0].next = virt_to_phys(&TxBulkDummyEPList[i][1]);
-
- /* The second one. */
- CHECK_ALIGN(&TxBulkDummyEPList[i][1]);
- TxBulkDummyEPList[i][1].hw_len = 0;
- TxBulkDummyEPList[i][1].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) |
- IO_STATE(USB_EP_command, eol, yes));
- TxBulkDummyEPList[i][1].sub = 0;
- /* The last dummy's next pointer is the same as the current EP's next pointer. */
- TxBulkDummyEPList[i][1].next = virt_to_phys(&TxBulkEPList[i + 1]);
- }
-
- /* Special handling of last descr in list, make list circular */
- epDescr = &TxBulkEPList[i];
- CHECK_ALIGN(epDescr);
- epDescr->hw_len = 0;
- epDescr->command = IO_STATE(USB_EP_command, eol, yes) |
- IO_FIELD(USB_EP_command, epid, i);
- epDescr->sub = 0;
- epDescr->next = virt_to_phys(&TxBulkEPList[0]);
-
- /* Init DMA sub-channel pointers to last item in each list */
- *R_DMA_CH8_SUB0_EP = virt_to_phys(&TxBulkEPList[i]);
- /* No point in starting the bulk channel yet.
- *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */
-}
-
-static void tc_dma_init_tx_ctrl_list(void) {
- int i;
- volatile struct USB_EP_Desc *epDescr;
-
- for (i = 0; i < (NBR_OF_EPIDS - 1); i++) {
- epDescr = &(TxCtrlEPList[i]);
- CHECK_ALIGN(epDescr);
- epDescr->hw_len = 0;
- epDescr->command = IO_FIELD(USB_EP_command, epid, i);
- epDescr->sub = 0;
- epDescr->next = virt_to_phys(&TxCtrlEPList[i + 1]);
- }
- /* Special handling of last descr in list, make list circular */
- epDescr = &TxCtrlEPList[i];
- CHECK_ALIGN(epDescr);
- epDescr->hw_len = 0;
- epDescr->command = IO_STATE(USB_EP_command, eol, yes) |
- IO_FIELD(USB_EP_command, epid, i);
- epDescr->sub = 0;
- epDescr->next = virt_to_phys(&TxCtrlEPList[0]);
-
- /* Init DMA sub-channel pointers to last item in each list */
- *R_DMA_CH8_SUB1_EP = virt_to_phys(&TxCtrlEPList[i]);
- /* No point in starting the ctrl channel yet.
- *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */
-}
-
-
-static void tc_dma_init_tx_intr_list(void) {
- int i;
-
- TxIntrSB_zout.sw_len = 1;
- TxIntrSB_zout.next = 0;
- TxIntrSB_zout.buf = virt_to_phys(&zout_buffer[0]);
- TxIntrSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) |
- IO_STATE(USB_SB_command, tt, zout) |
- IO_STATE(USB_SB_command, full, yes) |
- IO_STATE(USB_SB_command, eot, yes) |
- IO_STATE(USB_SB_command, eol, yes));
-
- for (i = 0; i < (MAX_INTR_INTERVAL - 1); i++) {
- CHECK_ALIGN(&TxIntrEPList[i]);
- TxIntrEPList[i].hw_len = 0;
- TxIntrEPList[i].command =
- (IO_STATE(USB_EP_command, eof, yes) |
- IO_STATE(USB_EP_command, enable, yes) |
- IO_FIELD(USB_EP_command, epid, INVALID_EPID));
- TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout);
- TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[i + 1]);
- }
-
- /* Special handling of last descr in list, make list circular */
- CHECK_ALIGN(&TxIntrEPList[i]);
- TxIntrEPList[i].hw_len = 0;
- TxIntrEPList[i].command =
- (IO_STATE(USB_EP_command, eof, yes) |
- IO_STATE(USB_EP_command, eol, yes) |
- IO_STATE(USB_EP_command, enable, yes) |
- IO_FIELD(USB_EP_command, epid, INVALID_EPID));
- TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout);
- TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[0]);
-
- intr_dbg("Initiated Intr EP descriptor list\n");
-
-
- /* Connect DMA 8 sub-channel 2 to first in list */
- *R_DMA_CH8_SUB2_EP = virt_to_phys(&TxIntrEPList[0]);
-}
-
-static void tc_dma_init_tx_isoc_list(void) {
- int i;
-
- DBFENTER;
-
- /* Read comment at zout_buffer declaration for an explanation to this. */
- TxIsocSB_zout.sw_len = 1;
- TxIsocSB_zout.next = 0;
- TxIsocSB_zout.buf = virt_to_phys(&zout_buffer[0]);
- TxIsocSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) |
- IO_STATE(USB_SB_command, tt, zout) |
- IO_STATE(USB_SB_command, full, yes) |
- IO_STATE(USB_SB_command, eot, yes) |
- IO_STATE(USB_SB_command, eol, yes));
-
- /* The last isochronous EP descriptor is a dummy. */
- for (i = 0; i < (NBR_OF_EPIDS - 1); i++) {
- CHECK_ALIGN(&TxIsocEPList[i]);
- TxIsocEPList[i].hw_len = 0;
- TxIsocEPList[i].command = IO_FIELD(USB_EP_command, epid, i);
- TxIsocEPList[i].sub = 0;
- TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[i + 1]);
- }
-
- CHECK_ALIGN(&TxIsocEPList[i]);
- TxIsocEPList[i].hw_len = 0;
-
- /* Must enable the last EP descr to get eof interrupt. */
- TxIsocEPList[i].command = (IO_STATE(USB_EP_command, enable, yes) |
- IO_STATE(USB_EP_command, eof, yes) |
- IO_STATE(USB_EP_command, eol, yes) |
- IO_FIELD(USB_EP_command, epid, INVALID_EPID));
- TxIsocEPList[i].sub = virt_to_phys(&TxIsocSB_zout);
- TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[0]);
-
- *R_DMA_CH8_SUB3_EP = virt_to_phys(&TxIsocEPList[0]);
- *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start);
-}
-
-static int tc_dma_init(struct usb_hcd *hcd) {
- tc_dma_init_rx_list();
- tc_dma_init_tx_bulk_list();
- tc_dma_init_tx_ctrl_list();
- tc_dma_init_tx_intr_list();
- tc_dma_init_tx_isoc_list();
- if (cris_request_dma(USB_TX_DMA_NBR,
- "ETRAX 100LX built-in USB (Tx)",
- DMA_VERBOSE_ON_ERROR,
- dma_usb)) {
- err("Could not allocate DMA ch 8 for USB");
- return -EBUSY;
- }
-
- if (cris_request_dma(USB_RX_DMA_NBR,
- "ETRAX 100LX built-in USB (Rx)",
- DMA_VERBOSE_ON_ERROR,
- dma_usb)) {
- err("Could not allocate DMA ch 9 for USB");
- return -EBUSY;
- }
-
- *R_IRQ_MASK2_SET =
- /* Note that these interrupts are not used. */
- IO_STATE(R_IRQ_MASK2_SET, dma8_sub0_descr, set) |
- /* Sub channel 1 (ctrl) descr. interrupts are used. */
- IO_STATE(R_IRQ_MASK2_SET, dma8_sub1_descr, set) |
- IO_STATE(R_IRQ_MASK2_SET, dma8_sub2_descr, set) |
- /* Sub channel 3 (isoc) descr. interrupts are used. */
- IO_STATE(R_IRQ_MASK2_SET, dma8_sub3_descr, set);
-
- /* Note that the dma9_descr interrupt is not used. */
- *R_IRQ_MASK2_SET =
- IO_STATE(R_IRQ_MASK2_SET, dma9_eop, set) |
- IO_STATE(R_IRQ_MASK2_SET, dma9_descr, set);
-
- if (request_irq(ETRAX_USB_RX_IRQ, tc_dma_rx_interrupt, 0,
- "ETRAX 100LX built-in USB (Rx)", hcd)) {
- err("Could not allocate IRQ %d for USB", ETRAX_USB_RX_IRQ);
- return -EBUSY;
- }
-
- if (request_irq(ETRAX_USB_TX_IRQ, tc_dma_tx_interrupt, 0,
- "ETRAX 100LX built-in USB (Tx)", hcd)) {
- err("Could not allocate IRQ %d for USB", ETRAX_USB_TX_IRQ);
- return -EBUSY;
- }
-
- return 0;
-}
-
-static void tc_dma_destroy(void) {
- free_irq(ETRAX_USB_RX_IRQ, NULL);
- free_irq(ETRAX_USB_TX_IRQ, NULL);
-
- cris_free_dma(USB_TX_DMA_NBR, "ETRAX 100LX built-in USB (Tx)");
- cris_free_dma(USB_RX_DMA_NBR, "ETRAX 100LX built-in USB (Rx)");
-
-}
-
-static void tc_dma_link_intr_urb(struct urb *urb);
-
-/* Handle processing of Bulk, Ctrl and Intr queues */
-static void tc_dma_process_queue(int epid) {
- struct urb *urb;
- struct crisv10_urb_priv *urb_priv;
- unsigned long flags;
- char toggle;
-
- if(epid_state[epid].disabled) {
- /* Don't process any URBs on a disabled endpoint */
- return;
- }
-
- /* Do not disturb us while fiddling with EPs and epids */
- local_irq_save(flags);
-
- /* For bulk, Ctrl and Intr can we only have one URB active at a time for
- a specific EP. */
- if(activeUrbList[epid] != NULL) {
- /* An URB is already active on EP, skip checking queue */
- local_irq_restore(flags);
- return;
- }
-
- urb = urb_list_first(epid);
- if(urb == NULL) {
- /* No URB waiting in EP queue. Nothing do to */
- local_irq_restore(flags);
- return;
- }
-
- urb_priv = urb->hcpriv;
- ASSERT(urb_priv != NULL);
- ASSERT(urb_priv->urb_state == NOT_STARTED);
- ASSERT(!usb_pipeisoc(urb->pipe));
-
- /* Remove this URB from the queue and move it to active */
- activeUrbList[epid] = urb;
- urb_list_del(urb, epid);
-
- urb_priv->urb_state = STARTED;
-
- /* Reset error counters (regardless of which direction this traffic is). */
- etrax_epid_clear_error(epid);
-
- /* Special handling of Intr EP lists */
- if(usb_pipeint(urb->pipe)) {
- tc_dma_link_intr_urb(urb);
- local_irq_restore(flags);
- return;
- }
-
- /* Software must preset the toggle bits for Bulk and Ctrl */
- if(usb_pipecontrol(urb->pipe)) {
- /* Toggle bits are initialized only during setup transaction in a
- CTRL transfer */
- etrax_epid_set_toggle(epid, 0, 0);
- etrax_epid_set_toggle(epid, 1, 0);
- } else {
- toggle = usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe),
- usb_pipeout(urb->pipe));
- etrax_epid_set_toggle(epid, usb_pipeout(urb->pipe), toggle);
- }
-
- tc_dbg("Added SBs from (URB:0x%x %s %s) to epid %d: %s\n",
- (unsigned int)urb, str_dir(urb->pipe), str_type(urb->pipe), epid,
- sblist_to_str(urb_priv->first_sb));
-
- /* We start the DMA sub channel without checking if it's running or not,
- because:
- 1) If it's already running, issuing the start command is a nop.
- 2) We avoid a test-and-set race condition. */
- switch(usb_pipetype(urb->pipe)) {
- case PIPE_BULK:
- /* Assert that the EP descriptor is disabled. */
- ASSERT(!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)));
-
- /* Set up and enable the EP descriptor. */
- TxBulkEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
- TxBulkEPList[epid].hw_len = 0;
- TxBulkEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
-
- /* Check if the dummy list is already with us (if several urbs were queued). */
- if (usb_pipein(urb->pipe) && (TxBulkEPList[epid].next != virt_to_phys(&TxBulkDummyEPList[epid][0]))) {
- tc_dbg("Inviting dummy list to the party for urb 0x%lx, epid %d",
- (unsigned long)urb, epid);
-
- /* We don't need to check if the DMA is at this EP or not before changing the
- next pointer, since we will do it in one 32-bit write (EP descriptors are
- 32-bit aligned). */
- TxBulkEPList[epid].next = virt_to_phys(&TxBulkDummyEPList[epid][0]);
- }
-
- restart_dma8_sub0();
-
- /* Update/restart the bulk start timer since we just started the channel.*/
- mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL);
- /* Update/restart the bulk eot timer since we just inserted traffic. */
- mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL);
- break;
- case PIPE_CONTROL:
- /* Assert that the EP descriptor is disabled. */
- ASSERT(!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)));
-
- /* Set up and enable the EP descriptor. */
- TxCtrlEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
- TxCtrlEPList[epid].hw_len = 0;
- TxCtrlEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
-
- *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB1_CMD, cmd, start);
- break;
- }
- local_irq_restore(flags);
-}
-
-static void tc_dma_link_intr_urb(struct urb *urb) {
- struct crisv10_urb_priv *urb_priv = urb->hcpriv;
- volatile struct USB_EP_Desc *tmp_ep;
- struct USB_EP_Desc *ep_desc;
- int i = 0, epid;
- int pool_idx = 0;
-
- ASSERT(urb_priv != NULL);
- epid = urb_priv->epid;
- ASSERT(urb_priv->interval > 0);
- ASSERT(urb_priv->intr_ep_pool_length > 0);
-
- tmp_ep = &TxIntrEPList[0];
-
- /* Only insert one EP descriptor in list for Out Intr URBs.
- We can only handle Out Intr with interval of 128ms because
- it's not possible to insert several Out Intr EPs because they
- are not consumed by the DMA. */
- if(usb_pipeout(urb->pipe)) {
- ep_desc = urb_priv->intr_ep_pool[0];
- ASSERT(ep_desc);
- ep_desc->next = tmp_ep->next;
- tmp_ep->next = virt_to_phys(ep_desc);
- i++;
- } else {
- /* Loop through Intr EP descriptor list and insert EP for URB at
- specified interval */
- do {
- /* Each EP descriptor with eof flag sat signals a new frame */
- if (tmp_ep->command & IO_MASK(USB_EP_command, eof)) {
- /* Insert a EP from URBs EP pool at correct interval */
- if ((i % urb_priv->interval) == 0) {
- ep_desc = urb_priv->intr_ep_pool[pool_idx];
- ASSERT(ep_desc);
- ep_desc->next = tmp_ep->next;
- tmp_ep->next = virt_to_phys(ep_desc);
- pool_idx++;
- ASSERT(pool_idx <= urb_priv->intr_ep_pool_length);
- }
- i++;
- }
- tmp_ep = (struct USB_EP_Desc *)phys_to_virt(tmp_ep->next);
- } while(tmp_ep != &TxIntrEPList[0]);
- }
-
- intr_dbg("Added SBs to intr epid %d: %s interval:%d (%d EP)\n", epid,
- sblist_to_str(urb_priv->first_sb), urb_priv->interval, pool_idx);
-
- /* We start the DMA sub channel without checking if it's running or not,
- because:
- 1) If it's already running, issuing the start command is a nop.
- 2) We avoid a test-and-set race condition. */
- *R_DMA_CH8_SUB2_CMD = IO_STATE(R_DMA_CH8_SUB2_CMD, cmd, start);
-}
-
-static void tc_dma_process_isoc_urb(struct urb *urb) {
- unsigned long flags;
- struct crisv10_urb_priv *urb_priv = urb->hcpriv;
- int epid;
-
- /* Do not disturb us while fiddling with EPs and epids */
- local_irq_save(flags);
-
- ASSERT(urb_priv);
- ASSERT(urb_priv->first_sb);
- epid = urb_priv->epid;
-
- if(activeUrbList[epid] == NULL) {
- /* EP is idle, so make this URB active */
- activeUrbList[epid] = urb;
- urb_list_del(urb, epid);
- ASSERT(TxIsocEPList[epid].sub == 0);
- ASSERT(!(TxIsocEPList[epid].command &
- IO_STATE(USB_EP_command, enable, yes)));
-
- /* Differentiate between In and Out Isoc. Because In SBs are not consumed*/
- if(usb_pipein(urb->pipe)) {
- /* Each EP for In Isoc will have only one SB descriptor, setup when
- submitting the first active urb. We do it here by copying from URBs
- pre-allocated SB. */
- memcpy((void *)&(TxIsocSBList[epid]), urb_priv->first_sb,
- sizeof(TxIsocSBList[epid]));
- TxIsocEPList[epid].hw_len = 0;
- TxIsocEPList[epid].sub = virt_to_phys(&(TxIsocSBList[epid]));
- } else {
- /* For Out Isoc we attach the pre-allocated list of SBs for the URB */
- TxIsocEPList[epid].hw_len = 0;
- TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
-
- isoc_dbg("Attached first URB:0x%x[%d] to epid:%d first_sb:0x%x"
- " last_sb::0x%x\n",
- (unsigned int)urb, urb_priv->urb_num, epid,
- (unsigned int)(urb_priv->first_sb),
- (unsigned int)(urb_priv->last_sb));
- }
-
- if (urb->transfer_flags & URB_ISO_ASAP) {
- /* The isoc transfer should be started as soon as possible. The
- start_frame field is a return value if URB_ISO_ASAP was set. Comparing
- R_USB_FM_NUMBER with a USB Chief trace shows that the first isoc IN
- token is sent 2 frames later. I'm not sure how this affects usage of
- the start_frame field by the device driver, or how it affects things
- when USB_ISO_ASAP is not set, so therefore there's no compensation for
- the 2 frame "lag" here. */
- urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff);
- TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes);
- urb_priv->urb_state = STARTED;
- isoc_dbg("URB_ISO_ASAP set, urb->start_frame set to %d\n",
- urb->start_frame);
- } else {
- /* Not started yet. */
- urb_priv->urb_state = NOT_STARTED;
- isoc_warn("urb_priv->urb_state set to NOT_STARTED for URB:0x%x\n",
- (unsigned int)urb);
- }
-
- } else {
- /* An URB is already active on the EP. Leave URB in queue and let
- finish_isoc_urb process it after current active URB */
- ASSERT(TxIsocEPList[epid].sub != 0);
-
- if(usb_pipein(urb->pipe)) {
- /* Because there already is a active In URB on this epid we do nothing
- and the finish_isoc_urb() function will handle switching to next URB*/
-
- } else { /* For Out Isoc, insert new URBs traffic last in SB-list. */
- struct USB_SB_Desc *temp_sb_desc;
-
- /* Set state STARTED to all Out Isoc URBs added to SB list because we
- don't know how many of them that are finished before descr interrupt*/
- urb_priv->urb_state = STARTED;
-
- /* Find end of current SB list by looking for SB with eol flag sat */
- temp_sb_desc = phys_to_virt(TxIsocEPList[epid].sub);
- while ((temp_sb_desc->command & IO_MASK(USB_SB_command, eol)) !=
- IO_STATE(USB_SB_command, eol, yes)) {
- ASSERT(temp_sb_desc->next);
- temp_sb_desc = phys_to_virt(temp_sb_desc->next);
- }
-
- isoc_dbg("Appended URB:0x%x[%d] (first:0x%x last:0x%x) to epid:%d"
- " sub:0x%x eol:0x%x\n",
- (unsigned int)urb, urb_priv->urb_num,
- (unsigned int)(urb_priv->first_sb),
- (unsigned int)(urb_priv->last_sb), epid,
- (unsigned int)phys_to_virt(TxIsocEPList[epid].sub),
- (unsigned int)temp_sb_desc);
-
- /* Next pointer must be set before eol is removed. */
- temp_sb_desc->next = virt_to_phys(urb_priv->first_sb);
- /* Clear the previous end of list flag since there is a new in the
- added SB descriptor list. */
- temp_sb_desc->command &= ~IO_MASK(USB_SB_command, eol);
-
- if (!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) {
- __u32 epid_data;
- /* 8.8.5 in Designer's Reference says we should check for and correct
- any errors in the EP here. That should not be necessary if
- epid_attn is handled correctly, so we assume all is ok. */
- epid_data = etrax_epid_iso_get(epid);
- if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) !=
- IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
- isoc_err("Disabled Isoc EP with error:%d on epid:%d when appending"
- " URB:0x%x[%d]\n",
- IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data), epid,
- (unsigned int)urb, urb_priv->urb_num);
- }
-
- /* The SB list was exhausted. */
- if (virt_to_phys(urb_priv->last_sb) != TxIsocEPList[epid].sub) {
- /* The new sublist did not get processed before the EP was
- disabled. Setup the EP again. */
-
- if(virt_to_phys(temp_sb_desc) == TxIsocEPList[epid].sub) {
- isoc_dbg("EP for epid:%d stoped at SB:0x%x before newly inserted"
- ", restarting from this URBs SB:0x%x\n",
- epid, (unsigned int)temp_sb_desc,
- (unsigned int)(urb_priv->first_sb));
- TxIsocEPList[epid].hw_len = 0;
- TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb);
- urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff);
- /* Enable the EP again so data gets processed this time */
- TxIsocEPList[epid].command |=
- IO_STATE(USB_EP_command, enable, yes);
-
- } else {
- /* The EP has been disabled but not at end this URB (god knows
- where). This should generate an epid_attn so we should not be
- here */
- isoc_warn("EP was disabled on sb:0x%x before SB list for"
- " URB:0x%x[%d] got processed\n",
- (unsigned int)phys_to_virt(TxIsocEPList[epid].sub),
- (unsigned int)urb, urb_priv->urb_num);
- }
- } else {
- /* This might happend if we are slow on this function and isn't
- an error. */
- isoc_dbg("EP was disabled and finished with SBs from appended"
- " URB:0x%x[%d]\n", (unsigned int)urb, urb_priv->urb_num);
- }
- }
- }
- }
-
- /* Start the DMA sub channel */
- *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start);
-
- local_irq_restore(flags);
-}
-
-static void tc_dma_unlink_intr_urb(struct urb *urb) {
- struct crisv10_urb_priv *urb_priv = urb->hcpriv;
- volatile struct USB_EP_Desc *first_ep; /* First EP in the list. */
- volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */
- volatile struct USB_EP_Desc *next_ep; /* The EP after current. */
- volatile struct USB_EP_Desc *unlink_ep; /* The one we should remove from
- the list. */
- int count = 0;
- volatile int timeout = 10000;
- int epid;
-
- /* Read 8.8.4 in Designer's Reference, "Removing an EP Descriptor from the
- List". */
- ASSERT(urb_priv);
- ASSERT(urb_priv->intr_ep_pool_length > 0);
- epid = urb_priv->epid;
-
- /* First disable all Intr EPs belonging to epid for this URB */
- first_ep = &TxIntrEPList[0];
- curr_ep = first_ep;
- do {
- next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
- if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) {
- /* Disable EP */
- next_ep->command &= ~IO_MASK(USB_EP_command, enable);
- }
- curr_ep = phys_to_virt(curr_ep->next);
- } while (curr_ep != first_ep);
-
-
- /* Now unlink all EPs belonging to this epid from Descr list */
- first_ep = &TxIntrEPList[0];
- curr_ep = first_ep;
- do {
- next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
- if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) {
- /* This is the one we should unlink. */
- unlink_ep = next_ep;
-
- /* Actually unlink the EP from the DMA list. */
- curr_ep->next = unlink_ep->next;
-
- /* Wait until the DMA is no longer at this descriptor. */
- while((*R_DMA_CH8_SUB2_EP == virt_to_phys(unlink_ep)) &&
- (timeout-- > 0));
-
- count++;
- }
- curr_ep = phys_to_virt(curr_ep->next);
- } while (curr_ep != first_ep);
-
- if(count != urb_priv->intr_ep_pool_length) {
- intr_warn("Unlinked %d of %d Intr EPs for URB:0x%x[%d]\n", count,
- urb_priv->intr_ep_pool_length, (unsigned int)urb,
- urb_priv->urb_num);
- } else {
- intr_dbg("Unlinked %d of %d interrupt EPs for URB:0x%x\n", count,
- urb_priv->intr_ep_pool_length, (unsigned int)urb);
- }
-}
-
-static void check_finished_bulk_tx_epids(struct usb_hcd *hcd,
- int timer) {
- unsigned long flags;
- int epid;
- struct urb *urb;
- struct crisv10_urb_priv * urb_priv;
- __u32 epid_data;
-
- /* Protect TxEPList */
- local_irq_save(flags);
-
- for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
- /* A finished EP descriptor is disabled and has a valid sub pointer */
- if (!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) &&
- (TxBulkEPList[epid].sub != 0)) {
-
- /* Get the active URB for this epid */
- urb = activeUrbList[epid];
- /* Sanity checks */
- ASSERT(urb);
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
-
- /* Only handle finished out Bulk EPs here,
- and let RX interrupt take care of the rest */
- if(!epid_out_traffic(epid)) {
- continue;
- }
-
- if(timer) {
- tc_warn("Found finished %s Bulk epid:%d URB:0x%x[%d] from timeout\n",
- epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb,
- urb_priv->urb_num);
- } else {
- tc_dbg("Found finished %s Bulk epid:%d URB:0x%x[%d] from interrupt\n",
- epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb,
- urb_priv->urb_num);
- }
-
- if(urb_priv->urb_state == UNLINK) {
- /* This Bulk URB is requested to be unlinked, that means that the EP
- has been disabled and we might not have sent all data */
- tc_finish_urb(hcd, urb, urb->status);
- continue;
- }
-
- ASSERT(urb_priv->urb_state == STARTED);
- if (phys_to_virt(TxBulkEPList[epid].sub) != urb_priv->last_sb) {
- tc_err("Endpoint got disabled before reaching last sb\n");
- }
-
- epid_data = etrax_epid_get(epid);
- if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) ==
- IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
- /* This means that the endpoint has no error, is disabled
- and had inserted traffic, i.e. transfer successfully completed. */
- tc_finish_urb(hcd, urb, 0);
- } else {
- /* Shouldn't happen. We expect errors to be caught by epid
- attention. */
- tc_err("Found disabled bulk EP desc (epid:%d error:%d)\n",
- epid, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data));
- }
- } else {
- tc_dbg("Ignoring In Bulk epid:%d, let RX interrupt handle it\n", epid);
- }
- }
-
- local_irq_restore(flags);
-}
-
-static void check_finished_ctrl_tx_epids(struct usb_hcd *hcd) {
- unsigned long flags;
- int epid;
- struct urb *urb;
- struct crisv10_urb_priv * urb_priv;
- __u32 epid_data;
-
- /* Protect TxEPList */
- local_irq_save(flags);
-
- for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
- if(epid == DUMMY_EPID)
- continue;
-
- /* A finished EP descriptor is disabled and has a valid sub pointer */
- if (!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) &&
- (TxCtrlEPList[epid].sub != 0)) {
-
- /* Get the active URB for this epid */
- urb = activeUrbList[epid];
-
- if(urb == NULL) {
- tc_warn("Found finished Ctrl epid:%d with no active URB\n", epid);
- continue;
- }
-
- /* Sanity checks */
- ASSERT(usb_pipein(urb->pipe));
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
- if (phys_to_virt(TxCtrlEPList[epid].sub) != urb_priv->last_sb) {
- tc_err("Endpoint got disabled before reaching last sb\n");
- }
-
- epid_data = etrax_epid_get(epid);
- if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) ==
- IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) {
- /* This means that the endpoint has no error, is disabled
- and had inserted traffic, i.e. transfer successfully completed. */
-
- /* Check if RX-interrupt for In Ctrl has been processed before
- finishing the URB */
- if(urb_priv->ctrl_rx_done) {
- tc_dbg("Finishing In Ctrl URB:0x%x[%d] in tx_interrupt\n",
- (unsigned int)urb, urb_priv->urb_num);
- tc_finish_urb(hcd, urb, 0);
- } else {
- /* If we get zout descriptor interrupt before RX was done for a
- In Ctrl transfer, then we flag that and it will be finished
- in the RX-Interrupt */
- urb_priv->ctrl_zout_done = 1;
- tc_dbg("Got zout descr interrupt before RX interrupt\n");
- }
- } else {
- /* Shouldn't happen. We expect errors to be caught by epid
- attention. */
- tc_err("Found disabled Ctrl EP desc (epid:%d URB:0x%x[%d]) error_code:%d\n", epid, (unsigned int)urb, urb_priv->urb_num, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data));
- __dump_ep_desc(&(TxCtrlEPList[epid]));
- __dump_ept_data(epid);
- }
- }
- }
- local_irq_restore(flags);
-}
-
-/* This function goes through all epids that are setup for Out Isoc transfers
- and marks (isoc_out_done) all queued URBs that the DMA has finished
- transfer for.
- No URB completetion is done here to make interrupt routine return quickly.
- URBs are completed later with help of complete_isoc_bottom_half() that
- becomes schedules when this functions is finished. */
-static void check_finished_isoc_tx_epids(void) {
- unsigned long flags;
- int epid;
- struct urb *urb;
- struct crisv10_urb_priv * urb_priv;
- struct USB_SB_Desc* sb_desc;
- int epid_done;
-
- /* Protect TxIsocEPList */
- local_irq_save(flags);
-
- for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
- if (TxIsocEPList[epid].sub == 0 || epid == INVALID_EPID ||
- !epid_out_traffic(epid)) {
- /* Nothing here to see. */
- continue;
- }
- ASSERT(epid_inuse(epid));
- ASSERT(epid_isoc(epid));
-
- sb_desc = phys_to_virt(TxIsocEPList[epid].sub);
- /* Find the last descriptor of the currently active URB for this ep.
- This is the first descriptor in the sub list marked for a descriptor
- interrupt. */
- while (sb_desc && !IO_EXTRACT(USB_SB_command, intr, sb_desc->command)) {
- sb_desc = sb_desc->next ? phys_to_virt(sb_desc->next) : 0;
- }
- ASSERT(sb_desc);
-
- isoc_dbg("Descr IRQ checking epid:%d sub:0x%x intr:0x%x\n",
- epid, (unsigned int)phys_to_virt(TxIsocEPList[epid].sub),
- (unsigned int)sb_desc);
-
- urb = activeUrbList[epid];
- if(urb == NULL) {
- isoc_err("Isoc Descr irq on epid:%d with no active URB\n", epid);
- continue;
- }
-
- epid_done = 0;
- while(urb && !epid_done) {
- /* Sanity check. */
- ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS);
- ASSERT(usb_pipeout(urb->pipe));
-
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
- ASSERT(urb_priv->urb_state == STARTED ||
- urb_priv->urb_state == UNLINK);
-
- if (sb_desc != urb_priv->last_sb) {
- /* This urb has been sent. */
- urb_priv->isoc_out_done = 1;
-
- } else { /* Found URB that has last_sb as the interrupt reason */
-
- /* Check if EP has been disabled, meaning that all transfers are done*/
- if(!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) {
- ASSERT((sb_desc->command & IO_MASK(USB_SB_command, eol)) ==
- IO_STATE(USB_SB_command, eol, yes));
- ASSERT(sb_desc->next == 0);
- urb_priv->isoc_out_done = 1;
- } else {
- isoc_dbg("Skipping URB:0x%x[%d] because EP not disabled yet\n",
- (unsigned int)urb, urb_priv->urb_num);
- }
- /* Stop looking any further in queue */
- epid_done = 1;
- }
-
- if (!epid_done) {
- if(urb == activeUrbList[epid]) {
- urb = urb_list_first(epid);
- } else {
- urb = urb_list_next(urb, epid);
- }
- }
- } /* END: while(urb && !epid_done) */
- }
-
- local_irq_restore(flags);
-}
-
-
-/* This is where the Out Isoc URBs are realy completed. This function is
- scheduled from tc_dma_tx_interrupt() when one or more Out Isoc transfers
- are done. This functions completes all URBs earlier marked with
- isoc_out_done by fast interrupt routine check_finished_isoc_tx_epids() */
-
-static void complete_isoc_bottom_half(struct work_struct* work) {
- struct crisv10_isoc_complete_data *comp_data;
- struct usb_iso_packet_descriptor *packet;
- struct crisv10_urb_priv * urb_priv;
- unsigned long flags;
- struct urb* urb;
- int epid_done;
- int epid;
- int i;
-
- comp_data = container_of(work, struct crisv10_isoc_complete_data, usb_bh);
-
- local_irq_save(flags);
-
- for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) {
- if(!epid_inuse(epid) || !epid_isoc(epid) || !epid_out_traffic(epid) || epid == DUMMY_EPID) {
- /* Only check valid Out Isoc epids */
- continue;
- }
-
- isoc_dbg("Isoc bottom-half checking epid:%d, sub:0x%x\n", epid,
- (unsigned int)phys_to_virt(TxIsocEPList[epid].sub));
-
- /* The descriptor interrupt handler has marked all transmitted Out Isoc
- URBs with isoc_out_done. Now we traverse all epids and for all that
- have out Isoc traffic we traverse its URB list and complete the
- transmitted URBs. */
- epid_done = 0;
- while (!epid_done) {
-
- /* Get the active urb (if any) */
- urb = activeUrbList[epid];
- if (urb == 0) {
- isoc_dbg("No active URB on epid:%d anymore\n", epid);
- epid_done = 1;
- continue;
- }
-
- /* Sanity check. */
- ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS);
- ASSERT(usb_pipeout(urb->pipe));
-
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
-
- if (!(urb_priv->isoc_out_done)) {
- /* We have reached URB that isn't flaged done yet, stop traversing. */
- isoc_dbg("Stoped traversing Out Isoc URBs on epid:%d"
- " before not yet flaged URB:0x%x[%d]\n",
- epid, (unsigned int)urb, urb_priv->urb_num);
- epid_done = 1;
- continue;
- }
-
- /* This urb has been sent. */
- isoc_dbg("Found URB:0x%x[%d] that is flaged isoc_out_done\n",
- (unsigned int)urb, urb_priv->urb_num);
-
- /* Set ok on transfered packets for this URB and finish it */
- for (i = 0; i < urb->number_of_packets; i++) {
- packet = &urb->iso_frame_desc[i];
- packet->status = 0;
- packet->actual_length = packet->length;
- }
- urb_priv->isoc_packet_counter = urb->number_of_packets;
- tc_finish_urb(comp_data->hcd, urb, 0);
-
- } /* END: while(!epid_done) */
- } /* END: for(epid...) */
-
- local_irq_restore(flags);
- kmem_cache_free(isoc_compl_cache, comp_data);
-}
-
-
-static void check_finished_intr_tx_epids(struct usb_hcd *hcd) {
- unsigned long flags;
- int epid;
- struct urb *urb;
- struct crisv10_urb_priv * urb_priv;
- volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */
- volatile struct USB_EP_Desc *next_ep; /* The EP after current. */
-
- /* Protect TxintrEPList */
- local_irq_save(flags);
-
- for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
- if(!epid_inuse(epid) || !epid_intr(epid) || !epid_out_traffic(epid)) {
- /* Nothing to see on this epid. Only check valid Out Intr epids */
- continue;
- }
-
- urb = activeUrbList[epid];
- if(urb == 0) {
- intr_warn("Found Out Intr epid:%d with no active URB\n", epid);
- continue;
- }
-
- /* Sanity check. */
- ASSERT(usb_pipetype(urb->pipe) == PIPE_INTERRUPT);
- ASSERT(usb_pipeout(urb->pipe));
-
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
-
- /* Go through EPs between first and second sof-EP. It's here Out Intr EPs
- are inserted.*/
- curr_ep = &TxIntrEPList[0];
- do {
- next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next);
- if(next_ep == urb_priv->intr_ep_pool[0]) {
- /* We found the Out Intr EP for this epid */
-
- /* Disable it so it doesn't get processed again */
- next_ep->command &= ~IO_MASK(USB_EP_command, enable);
-
- /* Finish the active Out Intr URB with status OK */
- tc_finish_urb(hcd, urb, 0);
- }
- curr_ep = phys_to_virt(curr_ep->next);
- } while (curr_ep != &TxIntrEPList[1]);
-
- }
- local_irq_restore(flags);
-}
-
-/* Interrupt handler for DMA8/IRQ24 with subchannels (called from hardware intr) */
-static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc) {
- struct usb_hcd *hcd = (struct usb_hcd*)vhc;
- ASSERT(hcd);
-
- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub0_descr)) {
- /* Clear this interrupt */
- *R_DMA_CH8_SUB0_CLR_INTR = IO_STATE(R_DMA_CH8_SUB0_CLR_INTR, clr_descr, do);
- restart_dma8_sub0();
- }
-
- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub1_descr)) {
- /* Clear this interrupt */
- *R_DMA_CH8_SUB1_CLR_INTR = IO_STATE(R_DMA_CH8_SUB1_CLR_INTR, clr_descr, do);
- check_finished_ctrl_tx_epids(hcd);
- }
-
- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub2_descr)) {
- /* Clear this interrupt */
- *R_DMA_CH8_SUB2_CLR_INTR = IO_STATE(R_DMA_CH8_SUB2_CLR_INTR, clr_descr, do);
- check_finished_intr_tx_epids(hcd);
- }
-
- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub3_descr)) {
- struct crisv10_isoc_complete_data* comp_data;
-
- /* Flag done Out Isoc for later completion */
- check_finished_isoc_tx_epids();
-
- /* Clear this interrupt */
- *R_DMA_CH8_SUB3_CLR_INTR = IO_STATE(R_DMA_CH8_SUB3_CLR_INTR, clr_descr, do);
- /* Schedule bottom half of Out Isoc completion function. This function
- finishes the URBs marked with isoc_out_done */
- comp_data = (struct crisv10_isoc_complete_data*)
- kmem_cache_alloc(isoc_compl_cache, GFP_ATOMIC);
- ASSERT(comp_data != NULL);
- comp_data ->hcd = hcd;
-
- INIT_WORK(&comp_data->usb_bh, complete_isoc_bottom_half);
- schedule_work(&comp_data->usb_bh);
- }
-
- return IRQ_HANDLED;
-}
-
-/* Interrupt handler for DMA9/IRQ25 (called from hardware intr) */
-static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc) {
- unsigned long flags;
- struct urb *urb;
- struct usb_hcd *hcd = (struct usb_hcd*)vhc;
- struct crisv10_urb_priv *urb_priv;
- int epid = 0;
- int real_error;
-
- ASSERT(hcd);
-
- /* Clear this interrupt. */
- *R_DMA_CH9_CLR_INTR = IO_STATE(R_DMA_CH9_CLR_INTR, clr_eop, do);
-
- /* Custom clear interrupt for this interrupt */
- /* The reason we cli here is that we call the driver's callback functions. */
- local_irq_save(flags);
-
- /* Note that this while loop assumes that all packets span only
- one rx descriptor. */
- while(myNextRxDesc->status & IO_MASK(USB_IN_status, eop)) {
- epid = IO_EXTRACT(USB_IN_status, epid, myNextRxDesc->status);
- /* Get the active URB for this epid */
- urb = activeUrbList[epid];
-
- ASSERT(epid_inuse(epid));
- if (!urb) {
- dma_err("No urb for epid %d in rx interrupt\n", epid);
- goto skip_out;
- }
-
- /* Check if any errors on epid */
- real_error = 0;
- if (myNextRxDesc->status & IO_MASK(USB_IN_status, error)) {
- __u32 r_usb_ept_data;
-
- if (usb_pipeisoc(urb->pipe)) {
- r_usb_ept_data = etrax_epid_iso_get(epid);
- if((r_usb_ept_data & IO_MASK(R_USB_EPT_DATA_ISO, valid)) &&
- (IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, r_usb_ept_data) == 0) &&
- (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata))) {
- /* Not an error, just a failure to receive an expected iso
- in packet in this frame. This is not documented
- in the designers reference. Continue processing.
- */
- } else real_error = 1;
- } else real_error = 1;
- }
-
- if(real_error) {
- dma_err("Error in RX descr on epid:%d for URB 0x%x",
- epid, (unsigned int)urb);
- dump_ept_data(epid);
- dump_in_desc(myNextRxDesc);
- goto skip_out;
- }
-
- urb_priv = (struct crisv10_urb_priv *)urb->hcpriv;
- ASSERT(urb_priv);
- ASSERT(urb_priv->urb_state == STARTED ||
- urb_priv->urb_state == UNLINK);
-
- if ((usb_pipetype(urb->pipe) == PIPE_BULK) ||
- (usb_pipetype(urb->pipe) == PIPE_CONTROL) ||
- (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) {
-
- /* We get nodata for empty data transactions, and the rx descriptor's
- hw_len field is not valid in that case. No data to copy in other
- words. */
- if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) {
- /* No data to copy */
- } else {
- /*
- dma_dbg("Processing RX for URB:0x%x epid:%d (data:%d ofs:%d)\n",
- (unsigned int)urb, epid, myNextRxDesc->hw_len,
- urb_priv->rx_offset);
- */
- /* Only copy data if URB isn't flaged to be unlinked*/
- if(urb_priv->urb_state != UNLINK) {
- /* Make sure the data fits in the buffer. */
- if(urb_priv->rx_offset + myNextRxDesc->hw_len
- <= urb->transfer_buffer_length) {
-
- /* Copy the data to URBs buffer */
- memcpy(urb->transfer_buffer + urb_priv->rx_offset,
- phys_to_virt(myNextRxDesc->buf), myNextRxDesc->hw_len);
- urb_priv->rx_offset += myNextRxDesc->hw_len;
- } else {
- /* Signal overflow when returning URB */
- urb->status = -EOVERFLOW;
- tc_finish_urb_later(hcd, urb, urb->status);
- }
- }
- }
-
- /* Check if it was the last packet in the transfer */
- if (myNextRxDesc->status & IO_MASK(USB_IN_status, eot)) {
- /* Special handling for In Ctrl URBs. */
- if(usb_pipecontrol(urb->pipe) && usb_pipein(urb->pipe) &&
- !(urb_priv->ctrl_zout_done)) {
- /* Flag that RX part of Ctrl transfer is done. Because zout descr
- interrupt hasn't happend yet will the URB be finished in the
- TX-Interrupt. */
- urb_priv->ctrl_rx_done = 1;
- tc_dbg("Not finishing In Ctrl URB:0x%x from rx_interrupt, waiting"
- " for zout\n", (unsigned int)urb);
- } else {
- tc_finish_urb(hcd, urb, 0);
- }
- }
- } else { /* ISOC RX */
- /*
- isoc_dbg("Processing RX for epid:%d (URB:0x%x) ISOC pipe\n",
- epid, (unsigned int)urb);
- */
-
- struct usb_iso_packet_descriptor *packet;
-
- if (urb_priv->urb_state == UNLINK) {
- isoc_warn("Ignoring Isoc Rx data for urb being unlinked.\n");
- goto skip_out;
- } else if (urb_priv->urb_state == NOT_STARTED) {
- isoc_err("What? Got Rx data for Isoc urb that isn't started?\n");
- goto skip_out;
- }
-
- packet = &urb->iso_frame_desc[urb_priv->isoc_packet_counter];
- ASSERT(packet);
- packet->status = 0;
-
- if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) {
- /* We get nodata for empty data transactions, and the rx descriptor's
- hw_len field is not valid in that case. We copy 0 bytes however to
- stay in synch. */
- packet->actual_length = 0;
- } else {
- packet->actual_length = myNextRxDesc->hw_len;
- /* Make sure the data fits in the buffer. */
- ASSERT(packet->actual_length <= packet->length);
- memcpy(urb->transfer_buffer + packet->offset,
- phys_to_virt(myNextRxDesc->buf), packet->actual_length);
- if(packet->actual_length > 0)
- isoc_dbg("Copied %d bytes, packet %d for URB:0x%x[%d]\n",
- packet->actual_length, urb_priv->isoc_packet_counter,
- (unsigned int)urb, urb_priv->urb_num);
- }
-
- /* Increment the packet counter. */
- urb_priv->isoc_packet_counter++;
-
- /* Note that we don't care about the eot field in the rx descriptor's
- status. It will always be set for isoc traffic. */
- if (urb->number_of_packets == urb_priv->isoc_packet_counter) {
- /* Complete the urb with status OK. */
- tc_finish_urb(hcd, urb, 0);
- }
- }
-
- skip_out:
- myNextRxDesc->status = 0;
- myNextRxDesc->command |= IO_MASK(USB_IN_command, eol);
- myLastRxDesc->command &= ~IO_MASK(USB_IN_command, eol);
- myLastRxDesc = myNextRxDesc;
- myNextRxDesc = phys_to_virt(myNextRxDesc->next);
- flush_etrax_cache();
- *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, restart);
- }
-
- local_irq_restore(flags);
-
- return IRQ_HANDLED;
-}
-
-static void tc_bulk_start_timer_func(unsigned long dummy) {
- /* We might enable an EP descriptor behind the current DMA position when
- it's about to decide that there are no more bulk traffic and it should
- stop the bulk channel.
- Therefore we periodically check if the bulk channel is stopped and there
- is an enabled bulk EP descriptor, in which case we start the bulk
- channel. */
-
- if (!(*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd))) {
- int epid;
-
- timer_dbg("bulk_start_timer: Bulk DMA channel not running.\n");
-
- for (epid = 0; epid < NBR_OF_EPIDS; epid++) {
- if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) {
- timer_warn("Found enabled EP for epid %d, starting bulk channel.\n",
- epid);
- restart_dma8_sub0();
-
- /* Restart the bulk eot timer since we just started the bulk channel.*/
- mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL);
-
- /* No need to search any further. */
- break;
- }
- }
- } else {
- timer_dbg("bulk_start_timer: Bulk DMA channel running.\n");
- }
-}
-
-static void tc_bulk_eot_timer_func(unsigned long dummy) {
- struct usb_hcd *hcd = (struct usb_hcd*)dummy;
- ASSERT(hcd);
- /* Because of a race condition in the top half, we might miss a bulk eot.
- This timer "simulates" a bulk eot if we don't get one for a while,
- hopefully correcting the situation. */
- timer_dbg("bulk_eot_timer timed out.\n");
- check_finished_bulk_tx_epids(hcd, 1);
-}
-
-
-/*************************************************************/
-/*************************************************************/
-/* Device driver block */
-/*************************************************************/
-/*************************************************************/
-
-/* Forward declarations for device driver functions */
-static int devdrv_hcd_probe(struct device *);
-static int devdrv_hcd_remove(struct device *);
-#ifdef CONFIG_PM
-static int devdrv_hcd_suspend(struct device *, u32, u32);
-static int devdrv_hcd_resume(struct device *, u32);
-#endif /* CONFIG_PM */
-
-/* the device */
-static struct platform_device *devdrv_hc_platform_device;
-
-/* device driver interface */
-static struct device_driver devdrv_hc_device_driver = {
- .name = (char *) hc_name,
- .bus = &platform_bus_type,
-
- .probe = devdrv_hcd_probe,
- .remove = devdrv_hcd_remove,
-
-#ifdef CONFIG_PM
- .suspend = devdrv_hcd_suspend,
- .resume = devdrv_hcd_resume,
-#endif /* CONFIG_PM */
-};
-
-/* initialize the host controller and driver */
-static int __init_or_module devdrv_hcd_probe(struct device *dev)
-{
- struct usb_hcd *hcd;
- struct crisv10_hcd *crisv10_hcd;
- int retval;
-
- /* Check DMA burst length */
- if(IO_EXTRACT(R_BUS_CONFIG, dma_burst, *R_BUS_CONFIG) !=
- IO_STATE(R_BUS_CONFIG, dma_burst, burst32)) {
- devdrv_err("Invalid DMA burst length in Etrax 100LX,"
- " needs to be 32\n");
- return -EPERM;
- }
-
- //XXX: dev->usb_id don't exist, using "" instread? - claudio
- hcd = usb_create_hcd(&crisv10_hc_driver, dev, "");
- if (!hcd)
- return -ENOMEM;
-
- crisv10_hcd = hcd_to_crisv10_hcd(hcd);
- spin_lock_init(&crisv10_hcd->lock);
- crisv10_hcd->num_ports = num_ports();
- crisv10_hcd->running = 0;
-
- dev_set_drvdata(dev, crisv10_hcd);
-
- devdrv_dbg("ETRAX USB IRQs HC:%d RX:%d TX:%d\n", ETRAX_USB_HC_IRQ,
- ETRAX_USB_RX_IRQ, ETRAX_USB_TX_IRQ);
-
- /* Print out chip version read from registers */
- int rev_maj = *R_USB_REVISION & IO_MASK(R_USB_REVISION, major);
- int rev_min = *R_USB_REVISION & IO_MASK(R_USB_REVISION, minor);
- if(rev_min == 0) {
- devdrv_info("Etrax 100LX USB Revision %d v1,2\n", rev_maj);
- } else {
- devdrv_info("Etrax 100LX USB Revision %d v%d\n", rev_maj, rev_min);
- }
-
- devdrv_info("Bulk timer interval, start:%d eot:%d\n",
- BULK_START_TIMER_INTERVAL,
- BULK_EOT_TIMER_INTERVAL);
-
-
- /* Init root hub data structures */
- if(rh_init()) {
- devdrv_err("Failed init data for Root Hub\n");
- retval = -ENOMEM;
- }
-
- if(port_in_use(0)) {
- if (cris_request_io_interface(if_usb_1, "ETRAX100LX USB-HCD")) {
- printk(KERN_CRIT "usb-host: request IO interface usb1 failed");
- retval = -EBUSY;
- goto out;
- }
- devdrv_info("Claimed interface for USB physical port 1\n");
- }
- if(port_in_use(1)) {
- if (cris_request_io_interface(if_usb_2, "ETRAX100LX USB-HCD")) {
- /* Free first interface if second failed to be claimed */
- if(port_in_use(0)) {
- cris_free_io_interface(if_usb_1);
- }
- printk(KERN_CRIT "usb-host: request IO interface usb2 failed");
- retval = -EBUSY;
- goto out;
- }
- devdrv_info("Claimed interface for USB physical port 2\n");
- }
-
- /* Init transfer controller structs and locks */
- if((retval = tc_init(hcd)) != 0) {
- goto out;
- }
-
- /* Attach interrupt functions for DMA and init DMA controller */
- if((retval = tc_dma_init(hcd)) != 0) {
- goto out;
- }
-
- /* Attach the top IRQ handler for USB controller interrupts */
- if (request_irq(ETRAX_USB_HC_IRQ, crisv10_hcd_top_irq, 0,
- "ETRAX 100LX built-in USB (HC)", hcd)) {
- err("Could not allocate IRQ %d for USB", ETRAX_USB_HC_IRQ);
- retval = -EBUSY;
- goto out;
- }
-
- /* iso_eof is only enabled when isoc traffic is running. */
- *R_USB_IRQ_MASK_SET =
- /* IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set) | */
- IO_STATE(R_USB_IRQ_MASK_SET, bulk_eot, set) |
- IO_STATE(R_USB_IRQ_MASK_SET, epid_attn, set) |
- IO_STATE(R_USB_IRQ_MASK_SET, port_status, set) |
- IO_STATE(R_USB_IRQ_MASK_SET, ctl_status, set);
-
-
- crisv10_ready_wait();
- /* Reset the USB interface. */
- *R_USB_COMMAND =
- IO_STATE(R_USB_COMMAND, port_sel, nop) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, reset);
-
- /* Designer's Reference, p. 8 - 10 says we should Initate R_USB_FM_PSTART to
- 0x2A30 (10800), to guarantee that control traffic gets 10% of the
- bandwidth, and periodic transfer may allocate the rest (90%).
- This doesn't work though.
- The value 11960 is chosen to be just after the SOF token, with a couple
- of bit times extra for possible bit stuffing. */
- *R_USB_FM_PSTART = IO_FIELD(R_USB_FM_PSTART, value, 11960);
-
- crisv10_ready_wait();
- /* Configure the USB interface as a host controller. */
- *R_USB_COMMAND =
- IO_STATE(R_USB_COMMAND, port_sel, nop) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_config);
-
-
- /* Check so controller not busy before enabling ports */
- crisv10_ready_wait();
-
- /* Enable selected USB ports */
- if(port_in_use(0)) {
- *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no);
- } else {
- *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, yes);
- }
- if(port_in_use(1)) {
- *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no);
- } else {
- *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, yes);
- }
-
- crisv10_ready_wait();
- /* Start processing of USB traffic. */
- *R_USB_COMMAND =
- IO_STATE(R_USB_COMMAND, port_sel, nop) |
- IO_STATE(R_USB_COMMAND, port_cmd, reset) |
- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run);
-
- /* Do not continue probing initialization before USB interface is done */
- crisv10_ready_wait();
-
- /* Register our Host Controller to USB Core
- * Finish the remaining parts of generic HCD initialization: allocate the
- * buffers of consistent memory, register the bus
- * and call the driver's reset() and start() routines. */
- retval = usb_add_hcd(hcd, ETRAX_USB_HC_IRQ, IRQF_DISABLED);
- if (retval != 0) {
- devdrv_err("Failed registering HCD driver\n");
- goto out;
- }
-
- return 0;
-
- out:
- devdrv_hcd_remove(dev);
- return retval;
-}
-
-
-/* cleanup after the host controller and driver */
-static int __init_or_module devdrv_hcd_remove(struct device *dev)
-{
- struct crisv10_hcd *crisv10_hcd = dev_get_drvdata(dev);
- struct usb_hcd *hcd;
-
- if (!crisv10_hcd)
- return 0;
- hcd = crisv10_hcd_to_hcd(crisv10_hcd);
-
-
- /* Stop USB Controller in Etrax 100LX */
- crisv10_hcd_reset(hcd);
-
- usb_remove_hcd(hcd);
- devdrv_dbg("Removed HCD from USB Core\n");
-
- /* Free USB Controller IRQ */
- free_irq(ETRAX_USB_HC_IRQ, NULL);
-
- /* Free resources */
- tc_dma_destroy();
- tc_destroy();
-
-
- if(port_in_use(0)) {
- cris_free_io_interface(if_usb_1);
- }
- if(port_in_use(1)) {
- cris_free_io_interface(if_usb_2);
- }
-
- devdrv_dbg("Freed all claimed resources\n");
-
- return 0;
-}
-
-
-#ifdef CONFIG_PM
-
-static int devdrv_hcd_suspend(struct usb_hcd *hcd, u32 state, u32 level)
-{
- return 0; /* no-op for now */
-}
-
-static int devdrv_hcd_resume(struct usb_hcd *hcd, u32 level)
-{
- return 0; /* no-op for now */
-}
-
-#endif /* CONFIG_PM */
-
-
-/*************************************************************/
-/*************************************************************/
-/* Module block */
-/*************************************************************/
-/*************************************************************/
-
-/* register driver */
-static int __init module_hcd_init(void)
-{
-
- if (usb_disabled())
- return -ENODEV;
-
- /* Here we select enabled ports by following defines created from
- menuconfig */
-#ifndef CONFIG_ETRAX_USB_HOST_PORT1
- ports &= ~(1<<0);
-#endif
-#ifndef CONFIG_ETRAX_USB_HOST_PORT2
- ports &= ~(1<<1);
-#endif
-
- printk(KERN_INFO "%s version "VERSION" "COPYRIGHT"\n", product_desc);
-
- devdrv_hc_platform_device =
- platform_device_register_simple((char *) hc_name, 0, NULL, 0);
-
- if (IS_ERR(devdrv_hc_platform_device))
- return PTR_ERR(devdrv_hc_platform_device);
- return driver_register(&devdrv_hc_device_driver);
- /*
- * Note that we do not set the DMA mask for the device,
- * i.e. we pretend that we will use PIO, since no specific
- * allocation routines are needed for DMA buffers. This will
- * cause the HCD buffer allocation routines to fall back to
- * kmalloc().
- */
-}
-
-/* unregister driver */
-static void __exit module_hcd_exit(void)
-{
- driver_unregister(&devdrv_hc_device_driver);
-}
-
-
-/* Module hooks */
-module_init(module_hcd_init);
-module_exit(module_hcd_exit);
diff --git a/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.h b/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.h
index 19a7e2e..36a1f83 100644
--- a/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.h
+++ b/target/linux/etrax/files-2.6.30/drivers/usb/host/hc-crisv10.h
@@ -331,336 +331,4 @@ typedef struct urb_entry
#define USB_SB_command__full__yes 1
#endif
-#ifndef __LINUX_ETRAX_USB_H
-#define __LINUX_ETRAX_USB_H
-
-#include <linux/types.h>
-#include <linux/list.h>
-
-struct USB_IN_Desc {
- volatile __u16 sw_len;
- volatile __u16 command;
- volatile unsigned long next;
- volatile unsigned long buf;
- volatile __u16 hw_len;
- volatile __u16 status;
-};
-
-struct USB_SB_Desc {
- volatile __u16 sw_len;
- volatile __u16 command;
- volatile unsigned long next;
- volatile unsigned long buf;
-};
-
-struct USB_EP_Desc {
- volatile __u16 hw_len;
- volatile __u16 command;
- volatile unsigned long sub;
- volatile unsigned long next;
-};
-
-
-/* Root Hub port status struct */
-struct crisv10_rh {
- volatile __u16 wPortChange[2];
- volatile __u16 wPortStatusPrev[2];
-};
-
-/* HCD description */
-struct crisv10_hcd {
- spinlock_t lock;
- __u8 num_ports;
- __u8 running;
-};
-
-
-/* Endpoint HC private data description */
-struct crisv10_ep_priv {
- int epid;
-};
-
-/* Additional software state info for a USB Controller epid */
-struct etrax_epid {
- __u8 inuse; /* !0 = setup in Etrax and used for a endpoint */
- __u8 disabled; /* !0 = Temporarly disabled to avoid resubmission */
- __u8 type; /* Setup as: PIPE_BULK, PIPE_CONTROL ... */
- __u8 out_traffic; /* !0 = This epid is for out traffic */
-};
-
-/* Struct to hold information of scheduled later URB completion */
-struct urb_later_data {
- struct delayed_work dws;
- struct usb_hcd *hcd;
- struct urb *urb;
- int urb_num;
- int status;
-};
-
-
-typedef enum {
- STARTED,
- NOT_STARTED,
- UNLINK,
-} crisv10_urb_state_t;
-
-
-struct crisv10_urb_priv {
- /* Sequence number for this URB. Every new submited URB gets this from
- a incrementing counter. Used when a URB is scheduled for later finish to
- be sure that the intended URB hasn't already been completed (device
- drivers has a tendency to reuse URBs once they are completed, causing us
- to not be able to single old ones out only based on the URB pointer.) */
- __u32 urb_num;
-
- /* The first_sb field is used for freeing all SB descriptors belonging
- to an urb. The corresponding ep descriptor's sub pointer cannot be
- used for this since the DMA advances the sub pointer as it processes
- the sb list. */
- struct USB_SB_Desc *first_sb;
-
- /* The last_sb field referes to the last SB descriptor that belongs to
- this urb. This is important to know so we can free the SB descriptors
- that ranges between first_sb and last_sb. */
- struct USB_SB_Desc *last_sb;
-
- /* The rx_offset field is used in ctrl and bulk traffic to keep track
- of the offset in the urb's transfer_buffer where incoming data should be
- copied to. */
- __u32 rx_offset;
-
- /* Counter used in isochronous transfers to keep track of the
- number of packets received/transmitted. */
- __u32 isoc_packet_counter;
-
- /* Flag that marks if this Isoc Out URB has finished it's transfer. Used
- because several URBs can be finished before list is processed */
- __u8 isoc_out_done;
-
- /* This field is used to pass information about the urb's current state
- between the various interrupt handlers (thus marked volatile). */
- volatile crisv10_urb_state_t urb_state;
-
- /* In Ctrl transfers consist of (at least) 3 packets: SETUP, IN and ZOUT.
- When DMA8 sub-channel 2 has processed the SB list for this sequence we
- get a interrupt. We also get a interrupt for In transfers and which
- one of these interrupts that comes first depends of data size and device.
- To be sure that we have got both interrupts before we complete the URB
- we have these to flags that shows which part that has completed.
- We can then check when we get one of the interrupts that if the other has
- occured it's safe for us to complete the URB, otherwise we set appropriate
- flag and do the completion when we get the other interrupt. */
- volatile unsigned char ctrl_zout_done;
- volatile unsigned char ctrl_rx_done;
-
- /* Connection between the submitted urb and ETRAX epid number */
- __u8 epid;
-
- /* The rx_data_list field is used for periodic traffic, to hold
- received data for later processing in the the complete_urb functions,
- where the data us copied to the urb's transfer_buffer. Basically, we
- use this intermediate storage because we don't know when it's safe to
- reuse the transfer_buffer (FIXME?). */
- struct list_head rx_data_list;
-
-
- /* The interval time rounded up to closest 2^N */
- int interval;
-
- /* Pool of EP descriptors needed if it's a INTR transfer.
- Amount of EPs in pool correspons to how many INTR that should
- be inserted in TxIntrEPList (max 128, defined by MAX_INTR_INTERVAL) */
- struct USB_EP_Desc* intr_ep_pool[128];
-
- /* The mount of EPs allocated for this INTR URB */
- int intr_ep_pool_length;
-
- /* Pointer to info struct if URB is scheduled to be finished later */
- struct urb_later_data* later_data;
-
- /* Allocated bandwidth for isochronous and interrupt traffic */
- int bandwidth;
-};
-
-
-/* This struct is for passing data from the top half to the bottom half irq
- handlers */
-struct crisv10_irq_reg {
- struct usb_hcd* hcd;
- __u32 r_usb_epid_attn;
- __u8 r_usb_status;
- __u16 r_usb_rh_port_status_1;
- __u16 r_usb_rh_port_status_2;
- __u32 r_usb_irq_mask_read;
- __u32 r_usb_fm_number;
- struct work_struct usb_bh;
-};
-
-
-/* This struct is for passing data from the isoc top half to the isoc bottom
- half. */
-struct crisv10_isoc_complete_data {
- struct usb_hcd *hcd;
- struct urb *urb;
- struct work_struct usb_bh;
-};
-
-/* Entry item for URB lists for each endpint */
-typedef struct urb_entry
-{
- struct urb *urb;
- struct list_head list;
-} urb_entry_t;
-
-/* ---------------------------------------------------------------------------
- Virtual Root HUB
- ------------------------------------------------------------------------- */
-/* destination of request */
-#define RH_INTERFACE 0x01
-#define RH_ENDPOINT 0x02
-#define RH_OTHER 0x03
-
-#define RH_CLASS 0x20
-#define RH_VENDOR 0x40
-
-/* Requests: bRequest << 8 | bmRequestType */
-#define RH_GET_STATUS 0x0080
-#define RH_CLEAR_FEATURE 0x0100
-#define RH_SET_FEATURE 0x0300
-#define RH_SET_ADDRESS 0x0500
-#define RH_GET_DESCRIPTOR 0x0680
-#define RH_SET_DESCRIPTOR 0x0700
-#define RH_GET_CONFIGURATION 0x0880
-#define RH_SET_CONFIGURATION 0x0900
-#define RH_GET_STATE 0x0280
-#define RH_GET_INTERFACE 0x0A80
-#define RH_SET_INTERFACE 0x0B00
-#define RH_SYNC_FRAME 0x0C80
-/* Our Vendor Specific Request */
-#define RH_SET_EP 0x2000
-
-
-/* Hub port features */
-#define RH_PORT_CONNECTION 0x00
-#define RH_PORT_ENABLE 0x01
-#define RH_PORT_SUSPEND 0x02
-#define RH_PORT_OVER_CURRENT 0x03
-#define RH_PORT_RESET 0x04
-#define RH_PORT_POWER 0x08
-#define RH_PORT_LOW_SPEED 0x09
-#define RH_C_PORT_CONNECTION 0x10
-#define RH_C_PORT_ENABLE 0x11
-#define RH_C_PORT_SUSPEND 0x12
-#define RH_C_PORT_OVER_CURRENT 0x13
-#define RH_C_PORT_RESET 0x14
-
-/* Hub features */
-#define RH_C_HUB_LOCAL_POWER 0x00
-#define RH_C_HUB_OVER_CURRENT 0x01
-
-#define RH_DEVICE_REMOTE_WAKEUP 0x00
-#define RH_ENDPOINT_STALL 0x01
-
-/* Our Vendor Specific feature */
-#define RH_REMOVE_EP 0x00
-
-
-#define RH_ACK 0x01
-#define RH_REQ_ERR -1
-#define RH_NACK 0x00
-
-/* Field definitions for */
-
-#define USB_IN_command__eol__BITNR 0 /* command macros */
-#define USB_IN_command__eol__WIDTH 1
-#define USB_IN_command__eol__no 0
-#define USB_IN_command__eol__yes 1
-
-#define USB_IN_command__intr__BITNR 3
-#define USB_IN_command__intr__WIDTH 1
-#define USB_IN_command__intr__no 0
-#define USB_IN_command__intr__yes 1
-#define USB_IN_status__eop__BITNR 1 /* status macros. */
-#define USB_IN_status__eop__WIDTH 1
-#define USB_IN_status__eop__no 0
-#define USB_IN_status__eop__yes 1
-
-#define USB_IN_status__eot__BITNR 5
-#define USB_IN_status__eot__WIDTH 1
-#define USB_IN_status__eot__no 0
-#define USB_IN_status__eot__yes 1
-
-#define USB_IN_status__error__BITNR 6
-#define USB_IN_status__error__WIDTH 1
-#define USB_IN_status__error__no 0
-#define USB_IN_status__error__yes 1
-
-#define USB_IN_status__nodata__BITNR 7
-#define USB_IN_status__nodata__WIDTH 1
-#define USB_IN_status__nodata__no 0
-#define USB_IN_status__nodata__yes 1
-
-#define USB_IN_status__epid__BITNR 8
-#define USB_IN_status__epid__WIDTH 5
-
-#define USB_EP_command__eol__BITNR 0
-#define USB_EP_command__eol__WIDTH 1
-#define USB_EP_command__eol__no 0
-#define USB_EP_command__eol__yes 1
-
-#define USB_EP_command__eof__BITNR 1
-#define USB_EP_command__eof__WIDTH 1
-#define USB_EP_command__eof__no 0
-#define USB_EP_command__eof__yes 1
-
-#define USB_EP_command__intr__BITNR 3
-#define USB_EP_command__intr__WIDTH 1
-#define USB_EP_command__intr__no 0
-#define USB_EP_command__intr__yes 1
-
-#define USB_EP_command__enable__BITNR 4
-#define USB_EP_command__enable__WIDTH 1
-#define USB_EP_command__enable__no 0
-#define USB_EP_command__enable__yes 1
-
-#define USB_EP_command__hw_valid__BITNR 5
-#define USB_EP_command__hw_valid__WIDTH 1
-#define USB_EP_command__hw_valid__no 0
-#define USB_EP_command__hw_valid__yes 1
-
-#define USB_EP_command__epid__BITNR 8
-#define USB_EP_command__epid__WIDTH 5
-
-#define USB_SB_command__eol__BITNR 0 /* command macros. */
-#define USB_SB_command__eol__WIDTH 1
-#define USB_SB_command__eol__no 0
-#define USB_SB_command__eol__yes 1
-
-#define USB_SB_command__eot__BITNR 1
-#define USB_SB_command__eot__WIDTH 1
-#define USB_SB_command__eot__no 0
-#define USB_SB_command__eot__yes 1
-
-#define USB_SB_command__intr__BITNR 3
-#define USB_SB_command__intr__WIDTH 1
-#define USB_SB_command__intr__no 0
-#define USB_SB_command__intr__yes 1
-
-#define USB_SB_command__tt__BITNR 4
-#define USB_SB_command__tt__WIDTH 2
-#define USB_SB_command__tt__zout 0
-#define USB_SB_command__tt__in 1
-#define USB_SB_command__tt__out 2
-#define USB_SB_command__tt__setup 3
-
-
-#define USB_SB_command__rem__BITNR 8
-#define USB_SB_command__rem__WIDTH 6
-
-#define USB_SB_command__full__BITNR 6
-#define USB_SB_command__full__WIDTH 1
-#define USB_SB_command__full__no 0
-#define USB_SB_command__full__yes 1
-
-#endif