diff options
8 files changed, 1528 insertions, 1173 deletions
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts new file mode 100644 index 0000000..fc13637 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-c2600.dts @@ -0,0 +1,412 @@ +#include "qcom-ipq8064-v1.0.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "TP-Link Archer C2600"; + compatible = "tplink,c2600", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + }; + + chosen { + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + drive-strength = <10>; + bias-none; + }; + }; + + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + + pullups { + pins = "gpio39"; + bias-pull-up; + }; + + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + gsbi5: gsbi@1a200000 { + qcom,mode = <GSBI_PROT_SPI>; + status = "ok"; + + spi4: spi@1a280000 { + status = "ok"; + spi-max-frequency = <50000000>; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 0>; + + flash: m25p80@0 { + compatible = "s25fl256s1"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x20000>; + read-only; + }; + SBL3@60000 { + label = "SBL3"; + reg = <0x60000 0x30000>; + read-only; + }; + DDRCONFIG@90000 { + label = "DDRCONFIG"; + reg = <0x90000 0x10000>; + read-only; + }; + SSD@a0000 { + label = "SSD"; + reg = <0xa0000 0x10000>; + read-only; + }; + TZ@b0000 { + label = "TZ"; + reg = <0xb0000 0x30000>; + read-only; + }; + RPM@e0000 { + label = "RPM"; + reg = <0xe0000 0x20000>; + read-only; + }; + fs-uboot@100000 { + label = "fs-uboot"; + reg = <0x100000 0x70000>; + read-only; + }; + uboot-env@170000 { + label = "uboot-env"; + reg = <0x170000 0x40000>; + read-only; + }; + radio@1b0000 { + label = "radio"; + reg = <0x1b0000 0x40000>; + read-only; + }; + os-image@1f0000 { + label = "os-image"; + reg = <0x1f0000 0x200000>; + }; + rootfs@3f0000 { + label = "rootfs"; + reg = <0x3f0000 0x1b00000>; + }; + defaultmac: default-mac@1ef0000 { + label = "default-mac"; + reg = <0x1ef0000 0x00200>; + read-only; + }; + pin@1ef0200 { + label = "pin"; + reg = <0x1ef0200 0x00200>; + read-only; + }; + product-info@1ef0400 { + label = "product-info"; + reg = <0x1ef0400 0x0fc00>; + read-only; + }; + partition-table@1f00000 { + label = "partition-table"; + reg = <0x1f00000 0x10000>; + read-only; + }; + soft-version@1f10000 { + label = "soft-version"; + reg = <0x1f10000 0x10000>; + read-only; + }; + support-list@1f20000 { + label = "support-list"; + reg = <0x1f20000 0x10000>; + read-only; + }; + profile@1f30000 { + label = "profile"; + reg = <0x1f30000 0x10000>; + read-only; + }; + default-config@1f40000 { + label = "default-config"; + reg = <0x1f40000 0x10000>; + read-only; + }; + user-config@1f50000 { + label = "user-config"; + reg = <0x1f50000 0x40000>; + read-only; + }; + qos-db@1f90000 { + label = "qos-db"; + reg = <0x1f90000 0x40000>; + read-only; + }; + usb-config@1fd0000 { + label = "usb-config"; + reg = <0x1fd0000 0x10000>; + read-only; + }; + log@1fe0000 { + label = "log"; + reg = <0x1fe0000 0x20000>; + read-only; + }; + }; + }; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + phy-tx0-term-offset = <7>; + }; + + pcie1: pci@1b700000 { + status = "ok"; + phy-tx0-term-offset = <7>; + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&defaultmac 0x8>; + mtd-mac-address-increment = <1>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&defaultmac 0x8>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 49 1>; + linux,code = <KEY_WLAN>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 64 1>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 1>; + linux,code = <KEY_WPS_BUTTON>; + }; + ledgeneral { + label = "ledgeneral"; + gpios = <&qcom_pinmux 16 1>; + linux,code = <KEY_DOLLAR>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + lan { + label = "lan:blue"; + gpios = <&qcom_pinmux 6 0>; + }; + usb4 { + label = "usb_4:blue"; + gpios = <&qcom_pinmux 7 0>; + }; + usb2 { + label = "usb_2:blue"; + gpios = <&qcom_pinmux 8 0>; + }; + wps { + label = "wps:blue"; + gpios = <&qcom_pinmux 9 0>; + }; + wan_blue { + label = "wan:blue"; + gpios = <&qcom_pinmux 33 1>; + }; + status { + label = "status:blue"; + gpios = <&qcom_pinmux 53 0>; + default-state = "on"; + }; + ledgnr { + label = "ledgnr:blue"; + gpios = <&qcom_pinmux 66 0>; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts new file mode 100644 index 0000000..bd294c5 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-d7800.dts @@ -0,0 +1,368 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Netgear Nighthawk X4 D7800"; + compatible = "netgear,d7800", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0xe000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; + + pcie0_pins: pcie0_pinmux { + mux { + pins = "gpio3"; + function = "pcie1_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + pcie1_pins: pcie1_pinmux { + mux { + pins = "gpio48"; + function = "pcie2_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + pullups { + pins = "gpio39"; + bias-pull-up; + }; + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + sata-phy@1b400000 { + status = "ok"; + }; + + sata@29000000 { + status = "ok"; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 3 0>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + }; + + pcie1: pci@1b700000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 48 0>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + }; + + nand@1ac00000 { + status = "ok"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + artbak: art@1340000 { + label = "artbak"; + reg = <0x1340000 0x0140000>; + read-only; + }; + + kernel@1480000 { + label = "kernel"; + reg = <0x1480000 0x0200000>; + }; + + ubi@1680000 { + label = "ubi"; + reg = <0x1680000 0x1E00000>; + }; + + netgear@3480000 { + label = "netgear"; + reg = <0x3480000 0x4480000>; + read-only; + }; + + reserve@7900000 { + label = "reserve"; + reg = <0x7900000 0x0700000>; + read-only; + }; + + firmware@1480000 { + label = "firmware"; + reg = <0x1480000 0x2000000>; + }; + + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 1>; + linux,code = <KEY_WLAN>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 1>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 1>; + linux,code = <KEY_WPS_BUTTON>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + usb1 { + label = "d7800:amber:usb1"; + gpios = <&qcom_pinmux 7 0>; + }; + + usb3 { + label = "d7800:amber:usb3"; + gpios = <&qcom_pinmux 8 0>; + }; + + status { + label = "d7800:amber:status"; + gpios = <&qcom_pinmux 9 0>; + }; + + internet { + label = "d7800:white:internet"; + gpios = <&qcom_pinmux 22 0>; + }; + + wan { + label = "d7800:white:wan"; + gpios = <&qcom_pinmux 23 0>; + }; + + wps { + label = "d7800:white:wps"; + gpios = <&qcom_pinmux 24 0>; + }; + + esata { + label = "d7800:white:esata"; + gpios = <&qcom_pinmux 26 0>; + }; + + power { + label = "d7800:white:power"; + gpios = <&qcom_pinmux 53 0>; + default-state = "on"; + }; + + rfkill { + label = "d7800:white:rfkill"; + gpios = <&qcom_pinmux 64 0>; + }; + + wifi5g { + label = "d7800:white:wifi5g"; + gpios = <&qcom_pinmux 67 0>; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts new file mode 100644 index 0000000..2c5e110 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ea8500.dts @@ -0,0 +1,380 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Linksys EA8500 WiFi Router"; + compatible = "linksys,ea8500", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + }; + + chosen { + bootargs = "console=ttyMSM0,115200n8"; + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + drive-strength = <10>; + bias-none; + }; + }; + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + pullups { + pins = "gpio39"; + bias-pull-up; + }; + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + + + + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + sata-phy@1b400000 { + status = "ok"; + }; + + sata@29000000 { + status = "ok"; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + phy-tx0-term-offset = <7>; + }; + + pcie1: pci@1b700000 { + status = "ok"; + phy-tx0-term-offset = <7>; + }; + + pcie2: pci@1b900000 { + status = "ok"; + phy-tx0-term-offset = <7>; + }; + + nand@1ac00000 { + status = "ok"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0000000 0x0040000>; + read-only; + }; + + MIBIB@40000 { + label = "MIBIB"; + reg = <0x0040000 0x0140000>; + read-only; + }; + + SBL2@180000 { + label = "SBL2"; + reg = <0x0180000 0x0140000>; + read-only; + }; + + SBL3@2c0000 { + label = "SBL3"; + reg = <0x02c0000 0x0280000>; + read-only; + }; + + DDRCONFIG@540000 { + label = "DDRCONFIG"; + reg = <0x0540000 0x0120000>; + read-only; + }; + + SSD@660000 { + label = "SSD"; + reg = <0x0660000 0x0120000>; + read-only; + }; + + TZ@780000 { + label = "TZ"; + reg = <0x0780000 0x0280000>; + read-only; + }; + + RPM@a00000 { + label = "RPM"; + reg = <0x0a00000 0x0280000>; + read-only; + }; + + art: art@c80000 { + label = "art"; + reg = <0x0c80000 0x0140000>; + read-only; + }; + + APPSBL@dc0000 { + label = "APPSBL"; + reg = <0x0dc0000 0x0100000>; + read-only; + }; + + u_env@ec0000 { + label = "u_env"; + reg = <0x0ec0000 0x0040000>; + }; + + s_env@f00000 { + label = "s_env"; + reg = <0x0f00000 0x0040000>; + }; + + devinfo@f40000 { + label = "devinfo"; + reg = <0x0f40000 0x0040000>; + }; + + linux@f80000 { + label = "kernel1"; + reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/ + }; + + rootfs@1280000 { + label = "rootfs1"; + reg = <0x1280000 0x2500000>; + }; + + linux2@3780000 { + label = "kernel2"; + reg = <0x3780000 0x2800000>; + }; + + rootfs2@3a80000 { + label = "rootfs2"; + reg = <0x3a80000 0x2500000>; + }; + + syscfg@5f80000 { + label = "syscfg"; + reg = <0x5f80000 0x2080000>; + }; + + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + qcom,rgmii_delay = <0>; + qcom,emulation = <0>; + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + //lan + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + qcom,phy_mdio_addr = <0>; /* none */ + qcom,poll_required = <0>; /* no polling */ + qcom,rgmii_delay = <0>; + qcom,emulation = <0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + adm_dma: dma@18300000 { + status = "ok"; + }; + + }; + + gpio-keys { + compatible = "gpio-keys"; + + rfkill { + label = "rfkill"; /* WIFI on-off*/ + gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RFKILL>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART >; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + + }; + + gpio-leds { + compatible = "gpio-leds"; + + wps { + label = "ea8500:green:wps"; + gpios = <&qcom_pinmux 53 0>; + default-state = "off"; + }; + + power { + label = "ea8500:white:power"; + gpios = <&qcom_pinmux 6 1>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + wifi { + label = "ea8500:green:wifi"; + gpios = <&qcom_pinmux 54 0>; + default-state = "off"; + }; + }; +}; diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts new file mode 100644 index 0000000..ca1f612 --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-r7500.dts @@ -0,0 +1,342 @@ +#include "qcom-ipq8064-v1.0.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "Netgear Nighthawk X4 R7500"; + compatible = "netgear,r7500", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0xe000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &uart4; + mdio-gpio0 = &mdio0; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + i2c4_pins: i2c4_pinmux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + bias-disable; + }; + + nand_pins: nand_pins { + mux { + pins = "gpio34", "gpio35", "gpio36", + "gpio37", "gpio38", "gpio39", + "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; + bias-disable; + }; + pullups { + pins = "gpio39"; + bias-pull-up; + }; + hold { + pins = "gpio40", "gpio41", "gpio42", + "gpio43", "gpio44", "gpio45", + "gpio46", "gpio47"; + bias-bus-hold; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + sata-phy@1b400000 { + status = "ok"; + }; + + sata@29000000 { + status = "ok"; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + }; + + pcie1: pci@1b700000 { + status = "ok"; + }; + + nand@1ac00000 { + status = "ok"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + + #address-cells = <1>; + #size-cells = <1>; + + qcadata@0 { + label = "qcadata"; + reg = <0x0000000 0x0c80000>; + read-only; + }; + + APPSBL@c80000 { + label = "APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + + APPSBLENV@1180000 { + label = "APPSBLENV"; + reg = <0x1180000 0x0080000>; + read-only; + }; + + art: art@1200000 { + label = "art"; + reg = <0x1200000 0x0140000>; + read-only; + }; + + kernel@1340000 { + label = "kernel"; + reg = <0x1340000 0x0200000>; + }; + + ubi@1540000 { + label = "ubi"; + reg = <0x1540000 0x1800000>; + }; + + netgear@2d40000 { + label = "netgear"; + reg = <0x2d40000 0x0c00000>; + read-only; + }; + + reserve@3940000 { + label = "reserve"; + reg = <0x3940000 0x46c0000>; + read-only; + }; + + firmware@1340000 { + label = "firmware"; + reg = <0x1340000 0x1a00000>; + }; + + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&art 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&art 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + wifi { + label = "wifi"; + gpios = <&qcom_pinmux 6 1>; + linux,code = <KEY_WLAN>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 1>; + linux,code = <KEY_RESTART>; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 65 1>; + linux,code = <KEY_WPS_BUTTON>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + usb1 { + label = "r7500:amber:usb1"; + gpios = <&qcom_pinmux 7 0>; + }; + + usb3 { + label = "r7500:amber:usb3"; + gpios = <&qcom_pinmux 8 0>; + }; + + status { + label = "r7500:amber:status"; + gpios = <&qcom_pinmux 9 0>; + }; + + internet { + label = "r7500:white:internet"; + gpios = <&qcom_pinmux 22 0>; + }; + + wan { + label = "r7500:white:wan"; + gpios = <&qcom_pinmux 23 0>; + }; + + wps { + label = "r7500:white:wps"; + gpios = <&qcom_pinmux 24 0>; + }; + + esata { + label = "r7500:white:esata"; + gpios = <&qcom_pinmux 26 0>; + }; + + power { + label = "r7500:white:power"; + gpios = <&qcom_pinmux 53 0>; + default-state = "on"; + }; + + rfkill { + label = "r7500:white:rfkill"; + gpios = <&qcom_pinmux 64 0>; + }; + + wifi5g { + label = "r7500:white:wifi5g"; + gpios = <&qcom_pinmux 67 0>; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/patches-4.4/800-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch b/target/linux/ipq806x/patches-4.4/800-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch deleted file mode 100644 index 1f5eba8..0000000 --- a/target/linux/ipq806x/patches-4.4/800-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch +++ /dev/null @@ -1,367 +0,0 @@ -From 7e77aa188a7a7c4391856a9e5ef5ef58f769e679 Mon Sep 17 00:00:00 2001 -From: Jonas Gorski <jogo@openwrt.org> -Date: Sun, 9 Aug 2015 13:02:38 +0200 -Subject: [PATCH] ARM: qcom: add Netgear Nighthawk X4 R7500 device tree - -Signed-off-by: Jonas Gorski <jogo@openwrt.org> ---- - arch/arm/boot/dts/Makefile | 1 + - arch/arm/boot/dts/qcom-ipq8064-r7500.dts | 370 +++++++++++++++++++++++++++++++ - 2 files changed, 371 insertions(+) - create mode 100644 arch/arm/boot/dts/qcom-ipq8064-r7500.dts - ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -452,6 +452,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ - qcom-apq8084-mtp.dtb \ - qcom-ipq8064-ap148.dtb \ - qcom-ipq8064-db149.dtb \ -+ qcom-ipq8064-r7500.dtb \ - qcom-msm8660-surf.dtb \ - qcom-msm8960-cdp.dtb \ - qcom-msm8974-sony-xperia-honami.dtb ---- /dev/null -+++ b/arch/arm/boot/dts/qcom-ipq8064-r7500.dts -@@ -0,0 +1,342 @@ -+#include "qcom-ipq8064-v1.0.dtsi" -+ -+#include <dt-bindings/input/input.h> -+ -+/ { -+ model = "Netgear Nighthawk X4 R7500"; -+ compatible = "netgear,r7500", "qcom,ipq8064"; -+ -+ memory@0 { -+ reg = <0x42000000 0xe000000>; -+ device_type = "memory"; -+ }; -+ -+ reserved-memory { -+ #address-cells = <1>; -+ #size-cells = <1>; -+ ranges; -+ rsvd@41200000 { -+ reg = <0x41200000 0x300000>; -+ no-map; -+ }; -+ }; -+ -+ aliases { -+ serial0 = &uart4; -+ mdio-gpio0 = &mdio0; -+ }; -+ -+ chosen { -+ bootargs = "rootfstype=squashfs noinitrd"; -+ linux,stdout-path = "serial0:115200n8"; -+ }; -+ -+ soc { -+ pinmux@800000 { -+ i2c4_pins: i2c4_pinmux { -+ pins = "gpio12", "gpio13"; -+ function = "gsbi4"; -+ bias-disable; -+ }; -+ -+ nand_pins: nand_pins { -+ mux { -+ pins = "gpio34", "gpio35", "gpio36", -+ "gpio37", "gpio38", "gpio39", -+ "gpio40", "gpio41", "gpio42", -+ "gpio43", "gpio44", "gpio45", -+ "gpio46", "gpio47"; -+ function = "nand"; -+ drive-strength = <10>; -+ bias-disable; -+ }; -+ pullups { -+ pins = "gpio39"; -+ bias-pull-up; -+ }; -+ hold { -+ pins = "gpio40", "gpio41", "gpio42", -+ "gpio43", "gpio44", "gpio45", -+ "gpio46", "gpio47"; -+ bias-bus-hold; -+ }; -+ }; -+ -+ mdio0_pins: mdio0_pins { -+ mux { -+ pins = "gpio0", "gpio1"; -+ function = "gpio"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; -+ -+ rgmii2_pins: rgmii2_pins { -+ mux { -+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", -+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; -+ function = "rgmii2"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; -+ }; -+ -+ gsbi@16300000 { -+ qcom,mode = <GSBI_PROT_I2C_UART>; -+ status = "ok"; -+ serial@16340000 { -+ status = "ok"; -+ }; -+ /* -+ * The i2c device on gsbi4 should not be enabled. -+ * On ipq806x designs gsbi4 i2c is meant for exclusive -+ * RPM usage. Turning this on in kernel manifests as -+ * i2c failure for the RPM. -+ */ -+ }; -+ -+ sata-phy@1b400000 { -+ status = "ok"; -+ }; -+ -+ sata@29000000 { -+ status = "ok"; -+ }; -+ -+ phy@100f8800 { /* USB3 port 1 HS phy */ -+ status = "ok"; -+ }; -+ -+ phy@100f8830 { /* USB3 port 1 SS phy */ -+ status = "ok"; -+ }; -+ -+ phy@110f8800 { /* USB3 port 0 HS phy */ -+ status = "ok"; -+ }; -+ -+ phy@110f8830 { /* USB3 port 0 SS phy */ -+ status = "ok"; -+ }; -+ -+ usb30@0 { -+ status = "ok"; -+ }; -+ -+ usb30@1 { -+ status = "ok"; -+ }; -+ -+ pcie0: pci@1b500000 { -+ status = "ok"; -+ }; -+ -+ pcie1: pci@1b700000 { -+ status = "ok"; -+ }; -+ -+ nand@1ac00000 { -+ status = "ok"; -+ -+ pinctrl-0 = <&nand_pins>; -+ pinctrl-names = "default"; -+ -+ nand-ecc-strength = <4>; -+ nand-bus-width = <8>; -+ -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ qcadata@0 { -+ label = "qcadata"; -+ reg = <0x0000000 0x0c80000>; -+ read-only; -+ }; -+ -+ APPSBL@c80000 { -+ label = "APPSBL"; -+ reg = <0x0c80000 0x0500000>; -+ read-only; -+ }; -+ -+ APPSBLENV@1180000 { -+ label = "APPSBLENV"; -+ reg = <0x1180000 0x0080000>; -+ read-only; -+ }; -+ -+ art: art@1200000 { -+ label = "art"; -+ reg = <0x1200000 0x0140000>; -+ read-only; -+ }; -+ -+ kernel@1340000 { -+ label = "kernel"; -+ reg = <0x1340000 0x0200000>; -+ }; -+ -+ ubi@1540000 { -+ label = "ubi"; -+ reg = <0x1540000 0x1800000>; -+ }; -+ -+ netgear@2d40000 { -+ label = "netgear"; -+ reg = <0x2d40000 0x0c00000>; -+ read-only; -+ }; -+ -+ reserve@3940000 { -+ label = "reserve"; -+ reg = <0x3940000 0x46c0000>; -+ read-only; -+ }; -+ -+ firmware@1340000 { -+ label = "firmware"; -+ reg = <0x1340000 0x1a00000>; -+ }; -+ -+ }; -+ -+ mdio0: mdio { -+ compatible = "virtual,mdio-gpio"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; -+ pinctrl-0 = <&mdio0_pins>; -+ pinctrl-names = "default"; -+ -+ phy0: ethernet-phy@0 { -+ device_type = "ethernet-phy"; -+ reg = <0>; -+ qca,ar8327-initvals = < -+ 0x00004 0x7600000 /* PAD0_MODE */ -+ 0x00008 0x1000000 /* PAD5_MODE */ -+ 0x0000c 0x80 /* PAD6_MODE */ -+ 0x000e4 0xaa545 /* MAC_POWER_SEL */ -+ 0x000e0 0xc74164de /* SGMII_CTRL */ -+ 0x0007c 0x4e /* PORT0_STATUS */ -+ 0x00094 0x4e /* PORT6_STATUS */ -+ >; -+ }; -+ -+ phy4: ethernet-phy@4 { -+ device_type = "ethernet-phy"; -+ reg = <4>; -+ }; -+ }; -+ -+ gmac1: ethernet@37200000 { -+ status = "ok"; -+ phy-mode = "rgmii"; -+ qcom,id = <1>; -+ -+ pinctrl-0 = <&rgmii2_pins>; -+ pinctrl-names = "default"; -+ -+ mtd-mac-address = <&art 6>; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ -+ gmac2: ethernet@37400000 { -+ status = "ok"; -+ phy-mode = "sgmii"; -+ qcom,id = <2>; -+ -+ mtd-mac-address = <&art 0>; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ }; -+ -+ gpio-keys { -+ compatible = "gpio-keys"; -+ -+ wifi { -+ label = "wifi"; -+ gpios = <&qcom_pinmux 6 1>; -+ linux,code = <KEY_WLAN>; -+ }; -+ -+ reset { -+ label = "reset"; -+ gpios = <&qcom_pinmux 54 1>; -+ linux,code = <KEY_RESTART>; -+ }; -+ -+ wps { -+ label = "wps"; -+ gpios = <&qcom_pinmux 65 1>; -+ linux,code = <KEY_WPS_BUTTON>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ usb1 { -+ label = "r7500:amber:usb1"; -+ gpios = <&qcom_pinmux 7 0>; -+ }; -+ -+ usb3 { -+ label = "r7500:amber:usb3"; -+ gpios = <&qcom_pinmux 8 0>; -+ }; -+ -+ status { -+ label = "r7500:amber:status"; -+ gpios = <&qcom_pinmux 9 0>; -+ }; -+ -+ internet { -+ label = "r7500:white:internet"; -+ gpios = <&qcom_pinmux 22 0>; -+ }; -+ -+ wan { -+ label = "r7500:white:wan"; -+ gpios = <&qcom_pinmux 23 0>; -+ }; -+ -+ wps { -+ label = "r7500:white:wps"; -+ gpios = <&qcom_pinmux 24 0>; -+ }; -+ -+ esata { -+ label = "r7500:white:esata"; -+ gpios = <&qcom_pinmux 26 0>; -+ }; -+ -+ power { -+ label = "r7500:white:power"; -+ gpios = <&qcom_pinmux 53 0>; -+ default-state = "on"; -+ }; -+ -+ rfkill { -+ label = "r7500:white:rfkill"; -+ gpios = <&qcom_pinmux 64 0>; -+ }; -+ -+ wifi5g { -+ label = "r7500:white:wifi5g"; -+ gpios = <&qcom_pinmux 67 0>; -+ }; -+ }; -+}; -+ -+&adm_dma { -+ status = "ok"; -+}; diff --git a/target/linux/ipq806x/patches-4.4/800-devicetree.patch b/target/linux/ipq806x/patches-4.4/800-devicetree.patch new file mode 100644 index 0000000..fc59837 --- /dev/null +++ b/target/linux/ipq806x/patches-4.4/800-devicetree.patch @@ -0,0 +1,26 @@ +From 7e77aa188a7a7c4391856a9e5ef5ef58f769e679 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 9 Aug 2015 13:02:38 +0200 +Subject: [PATCH] ARM: qcom: add Netgear Nighthawk X4 R7500 device tree + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/qcom-ipq8064-r7500.dts | 370 +++++++++++++++++++++++++++++++ + 2 files changed, 371 insertions(+) + create mode 100644 arch/arm/boot/dts/qcom-ipq8064-r7500.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -506,7 +506,11 @@ + qcom-apq8084-ifc6540.dtb \ + qcom-apq8084-mtp.dtb \ + qcom-ipq8064-ap148.dtb \ ++ qcom-ipq8064-c2600.dtb \ ++ qcom-ipq8064-d7800.dtb \ + qcom-ipq8064-db149.dtb \ ++ qcom-ipq8064-ea8500.dtb \ ++ qcom-ipq8064-r7500.dtb \ + qcom-msm8660-surf.dtb \ + qcom-msm8960-cdp.dtb \ + qcom-msm8974-sony-xperia-honami.dtb diff --git a/target/linux/ipq806x/patches-4.4/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch b/target/linux/ipq806x/patches-4.4/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch deleted file mode 100644 index eaf037f..0000000 --- a/target/linux/ipq806x/patches-4.4/801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch +++ /dev/null @@ -1,381 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -362,6 +362,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ - qcom-ipq8064-ap148.dtb \ - qcom-ipq8064-db149.dtb \ - qcom-ipq8064-r7500.dtb \ -+ qcom-ipq8064-d7800.dtb \ - qcom-msm8660-surf.dtb \ - qcom-msm8960-cdp.dtb \ - qcom-msm8974-sony-xperia-honami.dtb ---- /dev/null -+++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts -@@ -0,0 +1,368 @@ -+#include "qcom-ipq8064-v1.0.dtsi" -+ -+#include <dt-bindings/input/input.h> -+ -+/ { -+ model = "Netgear Nighthawk X4 D7800"; -+ compatible = "netgear,d7800", "qcom,ipq8064"; -+ -+ memory@0 { -+ reg = <0x42000000 0xe000000>; -+ device_type = "memory"; -+ }; -+ -+ reserved-memory { -+ #address-cells = <1>; -+ #size-cells = <1>; -+ ranges; -+ rsvd@41200000 { -+ reg = <0x41200000 0x300000>; -+ no-map; -+ }; -+ }; -+ -+ aliases { -+ serial0 = &uart4; -+ mdio-gpio0 = &mdio0; -+ }; -+ -+ chosen { -+ bootargs = "rootfstype=squashfs noinitrd"; -+ linux,stdout-path = "serial0:115200n8"; -+ }; -+ -+ soc { -+ pinmux@800000 { -+ i2c4_pins: i2c4_pinmux { -+ pins = "gpio12", "gpio13"; -+ function = "gsbi4"; -+ bias-disable; -+ }; -+ -+ pcie0_pins: pcie0_pinmux { -+ mux { -+ pins = "gpio3"; -+ function = "pcie1_rst"; -+ drive-strength = <12>; -+ bias-disable; -+ }; -+ }; -+ -+ pcie1_pins: pcie1_pinmux { -+ mux { -+ pins = "gpio48"; -+ function = "pcie2_rst"; -+ drive-strength = <12>; -+ bias-disable; -+ }; -+ }; -+ -+ nand_pins: nand_pins { -+ mux { -+ pins = "gpio34", "gpio35", "gpio36", -+ "gpio37", "gpio38", "gpio39", -+ "gpio40", "gpio41", "gpio42", -+ "gpio43", "gpio44", "gpio45", -+ "gpio46", "gpio47"; -+ function = "nand"; -+ drive-strength = <10>; -+ bias-disable; -+ }; -+ pullups { -+ pins = "gpio39"; -+ bias-pull-up; -+ }; -+ hold { -+ pins = "gpio40", "gpio41", "gpio42", -+ "gpio43", "gpio44", "gpio45", -+ "gpio46", "gpio47"; -+ bias-bus-hold; -+ }; -+ }; -+ -+ mdio0_pins: mdio0_pins { -+ mux { -+ pins = "gpio0", "gpio1"; -+ function = "gpio"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; -+ -+ rgmii2_pins: rgmii2_pins { -+ mux { -+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", -+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; -+ function = "rgmii2"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; -+ }; -+ -+ gsbi@16300000 { -+ qcom,mode = <GSBI_PROT_I2C_UART>; -+ status = "ok"; -+ serial@16340000 { -+ status = "ok"; -+ }; -+ /* -+ * The i2c device on gsbi4 should not be enabled. -+ * On ipq806x designs gsbi4 i2c is meant for exclusive -+ * RPM usage. Turning this on in kernel manifests as -+ * i2c failure for the RPM. -+ */ -+ }; -+ -+ sata-phy@1b400000 { -+ status = "ok"; -+ }; -+ -+ sata@29000000 { -+ status = "ok"; -+ }; -+ -+ phy@100f8800 { /* USB3 port 1 HS phy */ -+ status = "ok"; -+ }; -+ -+ phy@100f8830 { /* USB3 port 1 SS phy */ -+ status = "ok"; -+ }; -+ -+ phy@110f8800 { /* USB3 port 0 HS phy */ -+ status = "ok"; -+ }; -+ -+ phy@110f8830 { /* USB3 port 0 SS phy */ -+ status = "ok"; -+ }; -+ -+ usb30@0 { -+ status = "ok"; -+ }; -+ -+ usb30@1 { -+ status = "ok"; -+ }; -+ -+ pcie0: pci@1b500000 { -+ status = "ok"; -+ reset-gpio = <&qcom_pinmux 3 0>; -+ pinctrl-0 = <&pcie0_pins>; -+ pinctrl-names = "default"; -+ }; -+ -+ pcie1: pci@1b700000 { -+ status = "ok"; -+ reset-gpio = <&qcom_pinmux 48 0>; -+ pinctrl-0 = <&pcie1_pins>; -+ pinctrl-names = "default"; -+ }; -+ -+ nand@1ac00000 { -+ status = "ok"; -+ -+ pinctrl-0 = <&nand_pins>; -+ pinctrl-names = "default"; -+ -+ nand-ecc-strength = <4>; -+ nand-bus-width = <8>; -+ -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ qcadata@0 { -+ label = "qcadata"; -+ reg = <0x0000000 0x0c80000>; -+ read-only; -+ }; -+ -+ APPSBL@c80000 { -+ label = "APPSBL"; -+ reg = <0x0c80000 0x0500000>; -+ read-only; -+ }; -+ -+ APPSBLENV@1180000 { -+ label = "APPSBLENV"; -+ reg = <0x1180000 0x0080000>; -+ read-only; -+ }; -+ -+ art: art@1200000 { -+ label = "art"; -+ reg = <0x1200000 0x0140000>; -+ read-only; -+ }; -+ -+ artbak: art@1340000 { -+ label = "artbak"; -+ reg = <0x1340000 0x0140000>; -+ read-only; -+ }; -+ -+ kernel@1480000 { -+ label = "kernel"; -+ reg = <0x1480000 0x0200000>; -+ }; -+ -+ ubi@1680000 { -+ label = "ubi"; -+ reg = <0x1680000 0x1E00000>; -+ }; -+ -+ netgear@3480000 { -+ label = "netgear"; -+ reg = <0x3480000 0x4480000>; -+ read-only; -+ }; -+ -+ reserve@7900000 { -+ label = "reserve"; -+ reg = <0x7900000 0x0700000>; -+ read-only; -+ }; -+ -+ firmware@1480000 { -+ label = "firmware"; -+ reg = <0x1480000 0x2000000>; -+ }; -+ -+ }; -+ -+ mdio0: mdio { -+ compatible = "virtual,mdio-gpio"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; -+ pinctrl-0 = <&mdio0_pins>; -+ pinctrl-names = "default"; -+ -+ phy0: ethernet-phy@0 { -+ device_type = "ethernet-phy"; -+ reg = <0>; -+ qca,ar8327-initvals = < -+ 0x00004 0x7600000 /* PAD0_MODE */ -+ 0x00008 0x1000000 /* PAD5_MODE */ -+ 0x0000c 0x80 /* PAD6_MODE */ -+ 0x000e4 0xaa545 /* MAC_POWER_SEL */ -+ 0x000e0 0xc74164de /* SGMII_CTRL */ -+ 0x0007c 0x4e /* PORT0_STATUS */ -+ 0x00094 0x4e /* PORT6_STATUS */ -+ >; -+ }; -+ -+ phy4: ethernet-phy@4 { -+ device_type = "ethernet-phy"; -+ reg = <4>; -+ }; -+ }; -+ -+ gmac1: ethernet@37200000 { -+ status = "ok"; -+ phy-mode = "rgmii"; -+ phy-handle = <&phy4>; -+ qcom,id = <1>; -+ -+ pinctrl-0 = <&rgmii2_pins>; -+ pinctrl-names = "default"; -+ -+ mtd-mac-address = <&art 6>; -+ }; -+ -+ gmac2: ethernet@37400000 { -+ status = "ok"; -+ phy-mode = "sgmii"; -+ qcom,id = <2>; -+ -+ mtd-mac-address = <&art 0>; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ }; -+ -+ gpio-keys { -+ compatible = "gpio-keys"; -+ -+ wifi { -+ label = "wifi"; -+ gpios = <&qcom_pinmux 6 1>; -+ linux,code = <KEY_WLAN>; -+ }; -+ -+ reset { -+ label = "reset"; -+ gpios = <&qcom_pinmux 54 1>; -+ linux,code = <KEY_RESTART>; -+ }; -+ -+ wps { -+ label = "wps"; -+ gpios = <&qcom_pinmux 65 1>; -+ linux,code = <KEY_WPS_BUTTON>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ usb1 { -+ label = "d7800:amber:usb1"; -+ gpios = <&qcom_pinmux 7 0>; -+ }; -+ -+ usb3 { -+ label = "d7800:amber:usb3"; -+ gpios = <&qcom_pinmux 8 0>; -+ }; -+ -+ status { -+ label = "d7800:amber:status"; -+ gpios = <&qcom_pinmux 9 0>; -+ }; -+ -+ internet { -+ label = "d7800:white:internet"; -+ gpios = <&qcom_pinmux 22 0>; -+ }; -+ -+ wan { -+ label = "d7800:white:wan"; -+ gpios = <&qcom_pinmux 23 0>; -+ }; -+ -+ wps { -+ label = "d7800:white:wps"; -+ gpios = <&qcom_pinmux 24 0>; -+ }; -+ -+ esata { -+ label = "d7800:white:esata"; -+ gpios = <&qcom_pinmux 26 0>; -+ }; -+ -+ power { -+ label = "d7800:white:power"; -+ gpios = <&qcom_pinmux 53 0>; -+ default-state = "on"; -+ }; -+ -+ rfkill { -+ label = "d7800:white:rfkill"; -+ gpios = <&qcom_pinmux 64 0>; -+ }; -+ -+ wifi5g { -+ label = "d7800:white:wifi5g"; -+ gpios = <&qcom_pinmux 67 0>; -+ }; -+ }; -+}; -+ -+&adm_dma { -+ status = "ok"; -+}; diff --git a/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch b/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch deleted file mode 100644 index 8952f33..0000000 --- a/target/linux/ipq806x/patches-4.4/802-ARM-qcom-add-TPLink-C2600-device-tree.patch +++ /dev/null @@ -1,425 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -506,6 +506,7 @@ - qcom-apq8084-ifc6540.dtb \ - qcom-apq8084-mtp.dtb \ - qcom-ipq8064-ap148.dtb \ -+ qcom-ipq8064-c2600.dtb \ - qcom-ipq8064-db149.dtb \ - qcom-ipq8064-r7500.dtb \ - qcom-ipq8064-d7800.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts -@@ -0,0 +1,412 @@ -+#include "qcom-ipq8064-v1.0.dtsi" -+#include <dt-bindings/input/input.h> -+ -+/ { -+ model = "TP-Link Archer C2600"; -+ compatible = "tplink,c2600", "qcom,ipq8064"; -+ -+ memory@0 { -+ reg = <0x42000000 0x1e000000>; -+ device_type = "memory"; -+ }; -+ -+ reserved-memory { -+ #address-cells = <1>; -+ #size-cells = <1>; -+ ranges; -+ rsvd@41200000 { -+ reg = <0x41200000 0x300000>; -+ no-map; -+ }; -+ }; -+ -+ aliases { -+ serial0 = &uart4; -+ mdio-gpio0 = &mdio0; -+ }; -+ -+ chosen { -+ linux,stdout-path = "serial0:115200n8"; -+ }; -+ -+ soc { -+ pinmux@800000 { -+ i2c4_pins: i2c4_pinmux { -+ pins = "gpio12", "gpio13"; -+ function = "gsbi4"; -+ bias-disable; -+ }; -+ -+ spi_pins: spi_pins { -+ mux { -+ pins = "gpio18", "gpio19", "gpio21"; -+ function = "gsbi5"; -+ drive-strength = <10>; -+ bias-none; -+ }; -+ }; -+ -+ nand_pins: nand_pins { -+ mux { -+ pins = "gpio34", "gpio35", "gpio36", -+ "gpio37", "gpio38", "gpio39", -+ "gpio40", "gpio41", "gpio42", -+ "gpio43", "gpio44", "gpio45", -+ "gpio46", "gpio47"; -+ function = "nand"; -+ drive-strength = <10>; -+ bias-disable; -+ }; -+ -+ pullups { -+ pins = "gpio39"; -+ bias-pull-up; -+ }; -+ -+ hold { -+ pins = "gpio40", "gpio41", "gpio42", -+ "gpio43", "gpio44", "gpio45", -+ "gpio46", "gpio47"; -+ bias-bus-hold; -+ }; -+ }; -+ -+ mdio0_pins: mdio0_pins { -+ mux { -+ pins = "gpio0", "gpio1"; -+ function = "gpio"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; -+ -+ rgmii2_pins: rgmii2_pins { -+ mux { -+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", -+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; -+ function = "rgmii2"; -+ drive-strength = <8>; -+ bias-disable; -+ }; -+ }; -+ }; -+ -+ gsbi@16300000 { -+ qcom,mode = <GSBI_PROT_I2C_UART>; -+ status = "ok"; -+ serial@16340000 { -+ status = "ok"; -+ }; -+ /* -+ * The i2c device on gsbi4 should not be enabled. -+ * On ipq806x designs gsbi4 i2c is meant for exclusive -+ * RPM usage. Turning this on in kernel manifests as -+ * i2c failure for the RPM. -+ */ -+ }; -+ -+ gsbi5: gsbi@1a200000 { -+ qcom,mode = <GSBI_PROT_SPI>; -+ status = "ok"; -+ -+ spi4: spi@1a280000 { -+ status = "ok"; -+ spi-max-frequency = <50000000>; -+ -+ pinctrl-0 = <&spi_pins>; -+ pinctrl-names = "default"; -+ -+ cs-gpios = <&qcom_pinmux 20 0>; -+ -+ flash: m25p80@0 { -+ compatible = "s25fl256s1"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ spi-max-frequency = <50000000>; -+ reg = <0>; -+ -+ SBL1@0 { -+ label = "SBL1"; -+ reg = <0x0 0x20000>; -+ read-only; -+ }; -+ MIBIB@20000 { -+ label = "MIBIB"; -+ reg = <0x20000 0x20000>; -+ read-only; -+ }; -+ SBL2@40000 { -+ label = "SBL2"; -+ reg = <0x40000 0x20000>; -+ read-only; -+ }; -+ SBL3@60000 { -+ label = "SBL3"; -+ reg = <0x60000 0x30000>; -+ read-only; -+ }; -+ DDRCONFIG@90000 { -+ label = "DDRCONFIG"; -+ reg = <0x90000 0x10000>; -+ read-only; -+ }; -+ SSD@a0000 { -+ label = "SSD"; -+ reg = <0xa0000 0x10000>; -+ read-only; -+ }; -+ TZ@b0000 { -+ label = "TZ"; -+ reg = <0xb0000 0x30000>; -+ read-only; -+ }; -+ RPM@e0000 { -+ label = "RPM"; -+ reg = <0xe0000 0x20000>; -+ read-only; -+ }; -+ fs-uboot@100000 { -+ label = "fs-uboot"; -+ reg = <0x100000 0x70000>; -+ read-only; -+ }; -+ uboot-env@170000 { -+ label = "uboot-env"; -+ reg = <0x170000 0x40000>; -+ read-only; -+ }; -+ radio@1b0000 { -+ label = "radio"; -+ reg = <0x1b0000 0x40000>; -+ read-only; -+ }; -+ os-image@1f0000 { -+ label = "os-image"; -+ reg = <0x1f0000 0x200000>; -+ }; -+ rootfs@3f0000 { -+ label = "rootfs"; -+ reg = <0x3f0000 0x1b00000>; -+ }; -+ defaultmac: default-mac@1ef0000 { -+ label = "default-mac"; -+ reg = <0x1ef0000 0x00200>; -+ read-only; -+ }; -+ pin@1ef0200 { -+ label = "pin"; -+ reg = <0x1ef0200 0x00200>; -+ read-only; -+ }; -+ product-info@1ef0400 { -+ label = "product-info"; -+ reg = <0x1ef0400 0x0fc00>; -+ read-only; -+ }; -+ partition-table@1f00000 { -+ label = "partition-table"; -+ reg = <0x1f00000 0x10000>; -+ read-only; -+ }; -+ soft-version@1f10000 { -+ label = "soft-version"; -+ reg = <0x1f10000 0x10000>; -+ read-only; -+ }; -+ support-list@1f20000 { -+ label = "support-list"; -+ reg = <0x1f20000 0x10000>; -+ read-only; -+ }; -+ profile@1f30000 { -+ label = "profile"; -+ reg = <0x1f30000 0x10000>; -+ read-only; -+ }; -+ default-config@1f40000 { -+ label = "default-config"; -+ reg = <0x1f40000 0x10000>; -+ read-only; -+ }; -+ user-config@1f50000 { -+ label = "user-config"; -+ reg = <0x1f50000 0x40000>; -+ read-only; -+ }; -+ qos-db@1f90000 { -+ label = "qos-db"; -+ reg = <0x1f90000 0x40000>; -+ read-only; -+ }; -+ usb-config@1fd0000 { -+ label = "usb-config"; -+ reg = <0x1fd0000 0x10000>; -+ read-only; -+ }; -+ log@1fe0000 { -+ label = "log"; -+ reg = <0x1fe0000 0x20000>; -+ read-only; -+ }; -+ }; -+ }; -+ }; -+ -+ phy@100f8800 { /* USB3 port 1 HS phy */ -+ status = "ok"; -+ }; -+ -+ phy@100f8830 { /* USB3 port 1 SS phy */ -+ status = "ok"; -+ }; -+ -+ phy@110f8800 { /* USB3 port 0 HS phy */ -+ status = "ok"; -+ }; -+ -+ phy@110f8830 { /* USB3 port 0 SS phy */ -+ status = "ok"; -+ }; -+ -+ usb30@0 { -+ status = "ok"; -+ }; -+ -+ usb30@1 { -+ status = "ok"; -+ }; -+ -+ pcie0: pci@1b500000 { -+ status = "ok"; -+ phy-tx0-term-offset = <7>; -+ }; -+ -+ pcie1: pci@1b700000 { -+ status = "ok"; -+ phy-tx0-term-offset = <7>; -+ }; -+ -+ mdio0: mdio { -+ compatible = "virtual,mdio-gpio"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; -+ pinctrl-0 = <&mdio0_pins>; -+ pinctrl-names = "default"; -+ -+ phy0: ethernet-phy@0 { -+ device_type = "ethernet-phy"; -+ reg = <0>; -+ qca,ar8327-initvals = < -+ 0x00004 0x7600000 /* PAD0_MODE */ -+ 0x00008 0x1000000 /* PAD5_MODE */ -+ 0x0000c 0x80 /* PAD6_MODE */ -+ 0x000e4 0xaa545 /* MAC_POWER_SEL */ -+ 0x000e0 0xc74164de /* SGMII_CTRL */ -+ 0x0007c 0x4e /* PORT0_STATUS */ -+ 0x00094 0x4e /* PORT6_STATUS */ -+ >; -+ }; -+ -+ phy4: ethernet-phy@4 { -+ device_type = "ethernet-phy"; -+ reg = <4>; -+ }; -+ }; -+ -+ gmac1: ethernet@37200000 { -+ status = "ok"; -+ phy-mode = "rgmii"; -+ qcom,id = <1>; -+ -+ pinctrl-0 = <&rgmii2_pins>; -+ pinctrl-names = "default"; -+ -+ mtd-mac-address = <&defaultmac 0x8>; -+ mtd-mac-address-increment = <1>; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ -+ gmac2: ethernet@37400000 { -+ status = "ok"; -+ phy-mode = "sgmii"; -+ qcom,id = <2>; -+ -+ mtd-mac-address = <&defaultmac 0x8>; -+ -+ fixed-link { -+ speed = <1000>; -+ full-duplex; -+ }; -+ }; -+ }; -+ -+ gpio-keys { -+ compatible = "gpio-keys"; -+ -+ wifi { -+ label = "wifi"; -+ gpios = <&qcom_pinmux 49 1>; -+ linux,code = <KEY_WLAN>; -+ }; -+ -+ reset { -+ label = "reset"; -+ gpios = <&qcom_pinmux 64 1>; -+ linux,code = <KEY_RESTART>; -+ }; -+ -+ wps { -+ label = "wps"; -+ gpios = <&qcom_pinmux 65 1>; -+ linux,code = <KEY_WPS_BUTTON>; -+ }; -+ ledgeneral { -+ label = "ledgeneral"; -+ gpios = <&qcom_pinmux 16 1>; -+ linux,code = <KEY_DOLLAR>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ lan { -+ label = "lan:blue"; -+ gpios = <&qcom_pinmux 6 0>; -+ }; -+ usb4 { -+ label = "usb_4:blue"; -+ gpios = <&qcom_pinmux 7 0>; -+ }; -+ usb2 { -+ label = "usb_2:blue"; -+ gpios = <&qcom_pinmux 8 0>; -+ }; -+ wps { -+ label = "wps:blue"; -+ gpios = <&qcom_pinmux 9 0>; -+ }; -+ wan_blue { -+ label = "wan:blue"; -+ gpios = <&qcom_pinmux 33 1>; -+ }; -+ status { -+ label = "status:blue"; -+ gpios = <&qcom_pinmux 53 0>; -+ default-state = "on"; -+ }; -+ ledgnr { -+ label = "ledgnr:blue"; -+ gpios = <&qcom_pinmux 66 0>; -+ }; -+ }; -+}; -+ -+&adm_dma { -+ status = "ok"; -+}; |