diff options
| -rw-r--r-- | target/linux/kirkwood/config-default | 153 | ||||
| -rw-r--r-- | target/linux/kirkwood/patches/001-openwrt_partition_map.patch | 11 | ||||
| -rw-r--r-- | target/linux/kirkwood/patches/002-mvsdio_delay.patch | 32 | ||||
| -rw-r--r-- | target/linux/kirkwood/patches/200-iconnect.patch | 226 |
4 files changed, 0 insertions, 422 deletions
diff --git a/target/linux/kirkwood/config-default b/target/linux/kirkwood/config-default deleted file mode 100644 index d37d8ab..0000000 --- a/target/linux/kirkwood/config-default +++ /dev/null @@ -1,153 +0,0 @@ -CONFIG_ALIGNMENT_TRAP=y -CONFIG_ARCH_KIRKWOOD=y -# CONFIG_ARCH_NUC93X is not set -CONFIG_ARCH_REQUIRE_GPIOLIB=y -# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set -# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set -# CONFIG_ARCH_SUPPORTS_MSI is not set -CONFIG_ARCH_SUSPEND_POSSIBLE=y -# CONFIG_ARCH_USES_GETTIMEOFFSET is not set -CONFIG_ARM=y -CONFIG_ARM_L1_CACHE_SHIFT=5 -# CONFIG_ARM_THUMB is not set -# CONFIG_ARPD is not set -CONFIG_BITREVERSE=y -CONFIG_BLK_DEV_SD=y -CONFIG_CACHE_FEROCEON_L2=y -# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set -CONFIG_CMDLINE="rootdelay=1 root=/dev/mmcblk0p1 noinitrd console=ttyS0,115200" -CONFIG_CPU_32v5=y -CONFIG_CPU_ABRT_EV5T=y -CONFIG_CPU_CACHE_VIVT=y -CONFIG_CPU_COPY_FEROCEON=y -CONFIG_CPU_CP15=y -CONFIG_CPU_CP15_MMU=y -CONFIG_CPU_FEROCEON=y -# CONFIG_CPU_FEROCEON_OLD_ID is not set -# CONFIG_CPU_ICACHE_DISABLE is not set -CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_GOV_LADDER=y -CONFIG_CPU_PABRT_LEGACY=y -CONFIG_CPU_TLB_FEROCEON=y -CONFIG_DEBUG_KERNEL=y -# CONFIG_DEBUG_USER is not set -CONFIG_DECOMPRESS_LZMA=y -CONFIG_DEVPORT=y -# CONFIG_DLCI is not set -# CONFIG_DM9000 is not set -CONFIG_DNOTIFY=y -CONFIG_EXT4_FS=y -# CONFIG_FPE_FASTFPE is not set -# CONFIG_FPE_NWFPE is not set -CONFIG_FRAME_POINTER=y -CONFIG_GENERIC_ATOMIC64=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y -CONFIG_GENERIC_FIND_LAST_BIT=y -CONFIG_GENERIC_GPIO=y -CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y -CONFIG_GPIOLIB=y -# CONFIG_HAMRADIO is not set -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAVE_AOUT=y -CONFIG_HAVE_ARCH_KGDB=y -CONFIG_HAVE_FUNCTION_TRACER=y -CONFIG_HAVE_GENERIC_DMA_COHERENT=y -CONFIG_HAVE_IDE=y -CONFIG_HAVE_KERNEL_GZIP=y -CONFIG_HAVE_KERNEL_LZMA=y -CONFIG_HAVE_KERNEL_LZO=y -CONFIG_HAVE_KPROBES=y -CONFIG_HAVE_KRETPROBES=y -CONFIG_HAVE_LATENCYTOP_SUPPORT=y -CONFIG_HAVE_OPROFILE=y -CONFIG_HAVE_PERF_EVENTS=y -CONFIG_HAVE_PROC_CPU=y -CONFIG_HW_RANDOM=y -# CONFIG_I2C_MV64XXX is not set -CONFIG_INET_LRO=y -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_PIMSM_V1=y -CONFIG_IP_PIMSM_V2=y -CONFIG_JBD=y -CONFIG_LEDS_GPIO=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_MACH_D2NET_V2 is not set -# CONFIG_MACH_DB88F6281_BP is not set -CONFIG_MACH_DOCKSTAR=y -# CONFIG_MACH_ESATA_SHEEVAPLUG is not set -# CONFIG_MACH_GURUPLUG is not set -CONFIG_MACH_ICONNECT=y -# CONFIG_MACH_INETSPACE_V2 is not set -# CONFIG_MACH_MV88F6281GTW_GE is not set -# CONFIG_MACH_NET2BIG_V2 is not set -# CONFIG_MACH_NET5BIG_V2 is not set -# CONFIG_MACH_NETSPACE_MAX_V2 is not set -# CONFIG_MACH_NETSPACE_V2 is not set -CONFIG_MACH_OPENRD_BASE=y -CONFIG_MACH_OPENRD_CLIENT=y -# CONFIG_MACH_OPENRD_ULTIMATE is not set -# CONFIG_MACH_RD88F6192_NAS is not set -# CONFIG_MACH_RD88F6281 is not set -CONFIG_MACH_SHEEVAPLUG=y -# CONFIG_MACH_T5325 is not set -# CONFIG_MACH_TS219 is not set -# CONFIG_MACH_TS41X is not set -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_MVSDIO=y -# CONFIG_MMC_TIFM_SD is not set -# CONFIG_MTD_CFI is not set -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_NAND=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_ORION=y -# CONFIG_MTD_ROOTFS_ROOT_DEV is not set -# CONFIG_MTD_ROOTFS_SPLIT is not set -# CONFIG_MTD_SM_COMMON is not set -CONFIG_MV643XX_ETH=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NET_DSA=y -# CONFIG_NET_DSA_MV88E6060 is not set -# CONFIG_NET_DSA_MV88E6123_61_65 is not set -CONFIG_NET_DSA_MV88E6131=y -CONFIG_NET_DSA_MV88E6XXX=y -CONFIG_NET_DSA_MV88E6XXX_NEED_PPU=y -CONFIG_NET_DSA_TAG_DSA=y -# CONFIG_NET_DSA_TAG_EDSA is not set -# CONFIG_NET_DSA_TAG_TRAILER is not set -CONFIG_NLS=y -CONFIG_OUTER_CACHE=y -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_PAGE_OFFSET=0xC0000000 -CONFIG_PCI=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PHYLIB=y -CONFIG_PLAT_ORION=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_MV=y -CONFIG_SCSI=y -CONFIG_SCSI_MOD=y -# CONFIG_SCSI_MULTI_LUN is not set -# CONFIG_SDIO_UART is not set -# CONFIG_SERIAL_8250_EXTENDED is not set -CONFIG_SPLIT_PTLOCK_CPUS=999999 -CONFIG_SYS_SUPPORTS_APM_EMULATION=y -CONFIG_UID16=y -CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_STORAGE=y -CONFIG_USB_SUPPORT=y -# CONFIG_USB_UHCI_HCD is not set -CONFIG_VECTORS_BASE=0xffff0000 -# CONFIG_VFP is not set -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_WAN=y -CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_ZBOOT_ROM_TEXT=0x0 -CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/kirkwood/patches/001-openwrt_partition_map.patch b/target/linux/kirkwood/patches/001-openwrt_partition_map.patch deleted file mode 100644 index 0f94adc..0000000 --- a/target/linux/kirkwood/patches/001-openwrt_partition_map.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/mach-kirkwood/sheevaplug-setup.c -+++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c -@@ -33,7 +33,7 @@ static struct mtd_partition sheevaplug_n - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_4M - }, { -- .name = "root", -+ .name = "rootfs", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL - }, diff --git a/target/linux/kirkwood/patches/002-mvsdio_delay.patch b/target/linux/kirkwood/patches/002-mvsdio_delay.patch deleted file mode 100644 index ba28853..0000000 --- a/target/linux/kirkwood/patches/002-mvsdio_delay.patch +++ /dev/null @@ -1,32 +0,0 @@ ---- a/drivers/mmc/core/sd.c -+++ b/drivers/mmc/core/sd.c -@@ -332,6 +332,15 @@ int mmc_sd_switch_hs(struct mmc_card *ca - return -ENOMEM; - } - -+ /* -+ * Some SDHC cards, notably those with a Sandisk SD controller -+ * (also found in Kingston products) need a bit of slack -+ * before successfully handling the SWITCH command. So far, -+ * cards identifying themselves as "SD04G" and "SD08G" are -+ * affected -+ */ -+ udelay(1000); -+ - err = mmc_sd_switch(card, 1, 0, 1, status); - if (err) - goto out; ---- a/drivers/mmc/core/core.c -+++ b/drivers/mmc/core/core.c -@@ -303,9 +303,9 @@ void mmc_set_data_timeout(struct mmc_dat - * The limit is really 250 ms, but that is - * insufficient for some crappy cards. - */ -- limit_us = 300000; -+ limit_us = 500000; - else -- limit_us = 100000; -+ limit_us = 200000; - - /* - * SDHC cards always use these fixed values. diff --git a/target/linux/kirkwood/patches/200-iconnect.patch b/target/linux/kirkwood/patches/200-iconnect.patch deleted file mode 100644 index f8baae6..0000000 --- a/target/linux/kirkwood/patches/200-iconnect.patch +++ /dev/null @@ -1,226 +0,0 @@ ---- a/arch/arm/mach-kirkwood/Makefile -+++ b/arch/arm/mach-kirkwood/Makefile -@@ -8,6 +8,7 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheeva - obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o - obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o - obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o -+obj-$(CONFIG_MACH_ICONNECT) += iconnect-setup.o - obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o - obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o - obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o ---- a/arch/arm/mach-kirkwood/Kconfig -+++ b/arch/arm/mach-kirkwood/Kconfig -@@ -130,6 +130,12 @@ config MACH_T5325 - Say 'Y' here if you want your kernel to support the - HP t5325 Thin Client. - -+config MACH_ICONNECT -+ bool "Iomega iConnect Wireless" -+ help -+ Say 'Y' here if you want your kernel to support the -+ Iomega iConnect Wireless. -+ - endmenu - - endif ---- a/arch/arm/mach-kirkwood/mpp.h -+++ b/arch/arm/mach-kirkwood/mpp.h -@@ -108,6 +108,7 @@ - #define MPP11_SATA0_ACTn MPP( 11, 0x5, 0, 1, 0, 1, 1, 1, 1 ) - - #define MPP12_GPO MPP( 12, 0x0, 0, 1, 1, 1, 1, 1, 1 ) -+#define MPP12_GPIO MPP( 12, 0x0, 1, 1, 1, 1, 1, 1, 1 ) - #define MPP12_SD_CLK MPP( 12, 0x1, 0, 1, 1, 1, 1, 1, 1 ) - #define MPP12_AU_SPDIF0 MPP( 12, 0xa, 0, 1, 0, 0, 0, 0, 1 ) - #define MPP12_SPI_MOSI MPP( 12, 0xb, 0, 1, 0, 0, 0, 0, 1 ) ---- /dev/null -+++ b/arch/arm/mach-kirkwood/iconnect-setup.c -@@ -0,0 +1,188 @@ -+/* -+ * arch/arm/mach-kirkwood/iconnect-setup.c -+ * -+ * Iomega iConnect Wireless -+ * -+ * This file is licensed under the terms of the GNU General Public -+ * License version 2. This program is licensed "as is" without any -+ * warranty of any kind, whether express or implied. -+ */ -+ -+#include <linux/kernel.h> -+#include <linux/init.h> -+#include <linux/platform_device.h> -+#include <linux/irq.h> -+#include <linux/mtd/partitions.h> -+#include <linux/mv643xx_eth.h> -+#include <linux/ethtool.h> -+#include <linux/gpio.h> -+#include <linux/gpio_keys.h> -+#include <linux/input.h> -+#include <linux/leds.h> -+#include <asm/mach-types.h> -+#include <asm/mach/arch.h> -+#include <mach/kirkwood.h> -+#include "common.h" -+#include "mpp.h" -+ -+static struct mtd_partition iconnect_nand_parts[] = { -+ { -+ .name = "u-boot", -+ .offset = 0, -+ .size = SZ_1M -+ }, { -+ .name = "uImage", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = SZ_1M + SZ_2M -+ }, { -+ .name = "rootfs", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = SZ_32M, -+ }, { -+ .name = "data", -+ .offset = MTDPART_OFS_NXTBLK, -+ .size = MTDPART_SIZ_FULL -+ }, -+}; -+ -+static struct mv643xx_eth_platform_data iconnect_ge00_data = { -+ .phy_addr = MV643XX_ETH_PHY_ADDR(11), -+}; -+ -+static struct gpio_led iconnect_led_pins[] = { -+ { -+ .name = "iconnect:blue:power", -+ .default_trigger = "default-on", -+ .gpio = 42, -+ }, -+ { -+ .name = "iconnect:red:power", -+ .gpio = 43, -+ }, -+ { -+ .name = "iconnect:blue:usb1", -+ .gpio = 44, -+ }, -+ { -+ .name = "iconnect:blue:usb2", -+ .gpio = 45, -+ }, -+ { -+ .name = "iconnect:blue:usb3", -+ .gpio = 46, -+ }, -+ { -+ .name = "iconnect:blue:usb4", -+ .gpio = 47, -+ }, -+ { -+ .name = "iconnect:blue:otb", -+ .gpio = 48, -+ }, -+}; -+ -+static struct gpio_led_platform_data iconnect_led_data = { -+ .leds = iconnect_led_pins, -+ .num_leds = ARRAY_SIZE(iconnect_led_pins), -+}; -+ -+static struct platform_device iconnect_leds = { -+ .name = "leds-gpio", -+ .id = -1, -+ .dev = { -+ .platform_data = &iconnect_led_data, -+ } -+}; -+ -+#define ICONNECT_GPIO_KEY_RESET 12 -+#define ICONNECT_GPIO_KEY_OTB 35 -+ -+#define ICONNECT_SW_RESET 0x00 -+#define ICONNECT_SW_OTB 0x01 -+ -+static struct gpio_keys_button iconnect_buttons[] = { -+ { -+ .type = EV_SW, -+ .code = ICONNECT_SW_RESET, -+ .gpio = ICONNECT_GPIO_KEY_RESET, -+ .desc = "Reset Button", -+ .active_low = 1, -+ .debounce_interval = 100, -+ }, -+ { -+ .type = EV_SW, -+ .code = ICONNECT_SW_OTB, -+ .gpio = ICONNECT_GPIO_KEY_OTB, -+ .desc = "OTB Button", -+ .active_low = 1, -+ .debounce_interval = 100, -+ }, -+}; -+ -+static struct gpio_keys_platform_data iconnect_button_data = { -+ .buttons = iconnect_buttons, -+ .nbuttons = ARRAY_SIZE(iconnect_buttons), -+}; -+ -+static struct platform_device iconnect_button_device = { -+ .name = "gpio-keys", -+ .id = -1, -+ .num_resources = 0, -+ .dev = { -+ .platform_data = &iconnect_button_data, -+ }, -+}; -+ -+static unsigned int iconnect_mpp_config[] __initdata = { -+ MPP12_GPIO, /*Input for reset button*/ -+ MPP35_GPIO, /*Input for OTB button*/ -+ MPP42_GPIO, -+ MPP43_GPIO, -+ MPP44_GPIO, -+ MPP45_GPIO, -+ MPP46_GPIO, -+ MPP47_GPIO, -+ MPP48_GPIO, -+ 0 -+}; -+ -+static void __init iconnect_init(void) -+{ -+ u32 dev, rev; -+ -+ /* -+ * Basic setup. Needs to be called early. -+ */ -+ kirkwood_init(); -+ kirkwood_mpp_conf(iconnect_mpp_config); -+ -+ kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25); -+ kirkwood_ehci_init(); -+ -+ kirkwood_ge00_init(&iconnect_ge00_data); -+ kirkwood_pcie_id(&dev, &rev); -+ -+ kirkwood_uart0_init(); -+ kirkwood_i2c_init(); -+ -+ platform_device_register(&iconnect_leds); -+ platform_device_register(&iconnect_button_device); -+} -+ -+static int __init iconnect_pci_init(void) -+{ -+ if (machine_is_iconnect()) -+ kirkwood_pcie_init(KW_PCIE0); -+ -+ return 0; -+} -+subsys_initcall(iconnect_pci_init); -+ -+ -+MACHINE_START(ICONNECT, "Iomega iConnect Wireless") -+ .boot_params = 0x00000100, -+ .init_machine = iconnect_init, -+ .map_io = kirkwood_map_io, -+ .init_irq = kirkwood_init_irq, -+ .timer = &kirkwood_timer, -+MACHINE_END |