diff options
15 files changed, 577 insertions, 766 deletions
diff --git a/package/b43/patches/001-porting.patch b/package/b43/patches/001-porting.patch index 56f4d6d..bee94a6 100644 --- a/package/b43/patches/001-porting.patch +++ b/package/b43/patches/001-porting.patch @@ -2,39 +2,6 @@ Index: b43/main.c =================================================================== --- b43.orig/main.c 2008-02-15 22:39:48.000000000 +0100 +++ b43/main.c 2008-02-15 22:45:38.000000000 +0100 -@@ -2017,7 +2017,7 @@ static int b43_gpio_init(struct b43_wlde - mask |= 0x0180; - set |= 0x0180; - } -- if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_PACTRL) { -+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL) { - b43_write16(dev, B43_MMIO_GPIO_MASK, - b43_read16(dev, B43_MMIO_GPIO_MASK) - | 0x0200); -@@ -2384,7 +2384,7 @@ static void b43_periodic_every60sec(stru - return; - if (!b43_has_hardware_pctl(phy)) - b43_lo_g_ctl_mark_all_unused(dev); -- if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI) { -+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) { - b43_mac_suspend(dev); - b43_calc_nrssi_slope(dev); - if ((phy->radio_ver == 0x2050) && (phy->radio_rev == 8)) { -@@ -2794,11 +2794,14 @@ u8 b43_ieee80211_antenna_sanitize(struct - return 0; - } - -+#if 0 - /* Get the mask of available antennas. */ - if (dev->phy.gmode) - antenna_mask = dev->dev->bus->sprom.ant_available_bg; - else - antenna_mask = dev->dev->bus->sprom.ant_available_a; -+#endif -+ antenna_mask = 0xFF; //FIXME need ssb update - - if (!(antenna_mask & (1 << (antenna_nr - 1)))) { - /* This antenna is not available. Fall back to default. */ @@ -2939,7 +2942,7 @@ static int b43_op_set_key(struct ieee802 u8 algorithm; u8 index; @@ -57,336 +24,3 @@ Index: b43/main.c } return err; } -@@ -3349,13 +3354,13 @@ static void b43_bluetooth_coext_enable(s - struct ssb_sprom *sprom = &dev->dev->bus->sprom; - u32 hf; - -- if (!(sprom->boardflags_lo & B43_BFL_BTCOEXIST)) -+ if (!(sprom->r1.boardflags_lo & B43_BFL_BTCOEXIST)) - return; - if (dev->phy.type != B43_PHYTYPE_B && !dev->phy.gmode) - return; - - hf = b43_hf_read(dev); -- if (sprom->boardflags_lo & B43_BFL_BTCMOD) -+ if (sprom->r1.boardflags_lo & B43_BFL_BTCMOD) - hf |= B43_HF_BTCOEXALT; - else - hf |= B43_HF_BTCOEX; -@@ -3497,7 +3502,7 @@ static int b43_wireless_core_init(struct - hf |= B43_HF_SYMW; - if (phy->rev == 1) - hf |= B43_HF_GDCW; -- if (sprom->boardflags_lo & B43_BFL_PACTRL) -+ if (sprom->r1.boardflags_lo & B43_BFL_PACTRL) - hf |= B43_HF_OFDMPABOOST; - } else if (phy->type == B43_PHYTYPE_B) { - hf |= B43_HF_SYMW; -@@ -4001,10 +4006,10 @@ static void b43_sprom_fixup(struct ssb_b - /* boardflags workarounds */ - if (bus->boardinfo.vendor == SSB_BOARDVENDOR_DELL && - bus->chip_id == 0x4301 && bus->boardinfo.rev == 0x74) -- bus->sprom.boardflags_lo |= B43_BFL_BTCOEXIST; -+ bus->sprom.r1.boardflags_lo |= B43_BFL_BTCOEXIST; - if (bus->boardinfo.vendor == PCI_VENDOR_ID_APPLE && - bus->boardinfo.type == 0x4E && bus->boardinfo.rev > 0x40) -- bus->sprom.boardflags_lo |= B43_BFL_PACTRL; -+ bus->sprom.r1.boardflags_lo |= B43_BFL_PACTRL; - } - - static void b43_wireless_exit(struct ssb_device *dev, struct b43_wl *wl) -@@ -4038,10 +4043,10 @@ static int b43_wireless_init(struct ssb_ - hw->max_noise = -110; - hw->queues = 1; /* FIXME: hardware has more queues */ - SET_IEEE80211_DEV(hw, dev->dev); -- if (is_valid_ether_addr(sprom->et1mac)) -- SET_IEEE80211_PERM_ADDR(hw, sprom->et1mac); -+ if (is_valid_ether_addr(sprom->r1.et1mac)) -+ SET_IEEE80211_PERM_ADDR(hw, sprom->r1.et1mac); - else -- SET_IEEE80211_PERM_ADDR(hw, sprom->il0mac); -+ SET_IEEE80211_PERM_ADDR(hw, sprom->r1.il0mac); - - /* Get and initialize struct b43_wl */ - wl = hw_to_b43_wl(hw); -Index: b43/leds.c -=================================================================== ---- b43.orig/leds.c 2008-02-06 00:55:14.000000000 +0100 -+++ b43/leds.c 2008-02-15 22:51:32.000000000 +0100 -@@ -190,10 +190,10 @@ void b43_leds_init(struct b43_wldev *dev - enum b43_led_behaviour behaviour; - bool activelow; - -- sprom[0] = bus->sprom.gpio0; -- sprom[1] = bus->sprom.gpio1; -- sprom[2] = bus->sprom.gpio2; -- sprom[3] = bus->sprom.gpio3; -+ sprom[0] = bus->sprom.r1.gpio0; -+ sprom[1] = bus->sprom.r1.gpio1; -+ sprom[2] = bus->sprom.r1.gpio2; -+ sprom[3] = bus->sprom.r1.gpio3; - - for (i = 0; i < 4; i++) { - if (sprom[i] == 0xFF) { -Index: b43/lo.c -=================================================================== ---- b43.orig/lo.c 2008-02-06 00:55:14.000000000 +0100 -+++ b43/lo.c 2008-02-15 22:50:17.000000000 +0100 -@@ -264,7 +264,7 @@ static u16 lo_measure_feedthrough(struct - rfover |= pga; - rfover |= lna; - rfover |= trsw_rx; -- if ((dev->dev->bus->sprom.boardflags_lo & B43_BFL_EXTLNA) -+ if ((dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_EXTLNA) - && phy->rev > 6) - rfover |= B43_PHY_RFOVERVAL_EXTLNA; - -@@ -634,7 +634,7 @@ static void lo_measure_setup(struct b43_ - & 0xFFFC); - if (phy->type == B43_PHYTYPE_G) { - if ((phy->rev >= 7) && -- (sprom->boardflags_lo & B43_BFL_EXTLNA)) { -+ (sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) { - b43_phy_write(dev, B43_PHY_RFOVER, 0x933); - } else { - b43_phy_write(dev, B43_PHY_RFOVER, 0x133); -Index: b43/nphy.c -=================================================================== ---- b43.orig/nphy.c 2008-02-06 00:55:14.000000000 +0100 -+++ b43/nphy.c 2008-02-15 22:48:51.000000000 +0100 -@@ -134,6 +134,8 @@ static void b43_radio_init2055_post(stru - - b43_radio_mask(dev, B2055_MASTER1, 0xFFF3); - msleep(1); -+//FIXME ssb update needed -+#if 0 - if ((sprom->revision != 4) || !(sprom->boardflags_hi & 0x0002)) { - if ((binfo->vendor != PCI_VENDOR_ID_BROADCOM) || - (binfo->type != 0x46D) || -@@ -143,6 +145,7 @@ static void b43_radio_init2055_post(stru - msleep(1); - } - } -+#endif - b43_radio_maskset(dev, B2055_RRCCAL_NOPTSEL, 0x3F, 0x2C); - msleep(1); - b43_radio_write16(dev, B2055_CAL_MISC, 0x3C); -Index: b43/phy.c -=================================================================== ---- b43.orig/phy.c 2008-02-06 00:55:14.000000000 +0100 -+++ b43/phy.c 2008-02-15 22:47:55.000000000 +0100 -@@ -924,7 +924,7 @@ static void b43_phy_inita(struct b43_wld - } - - if ((phy->type == B43_PHYTYPE_G) && -- (dev->dev->bus->sprom.boardflags_lo & B43_BFL_PACTRL)) { -+ (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL)) { - b43_phy_write(dev, B43_PHY_OFDM(0x6E), - (b43_phy_read(dev, B43_PHY_OFDM(0x6E)) - & 0xE000) | 0x3CF); -@@ -1027,7 +1027,7 @@ static void b43_phy_initb4(struct b43_wl - if (phy->radio_ver == 0x2050) - b43_phy_write(dev, 0x002A, 0x88C2); - b43_set_txpower_g(dev, &phy->bbatt, &phy->rfatt, phy->tx_control); -- if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI) { -+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) { - b43_calc_nrssi_slope(dev); - b43_calc_nrssi_threshold(dev); - } -@@ -1174,7 +1174,7 @@ static void b43_phy_initb6(struct b43_wl - b43_radio_write16(dev, 0x5A, 0x88); - b43_radio_write16(dev, 0x5B, 0x6B); - b43_radio_write16(dev, 0x5C, 0x0F); -- if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_ALTIQ) { -+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_ALTIQ) { - b43_radio_write16(dev, 0x5D, 0xFA); - b43_radio_write16(dev, 0x5E, 0xD8); - } else { -@@ -1266,7 +1266,7 @@ static void b43_phy_initb6(struct b43_wl - b43_phy_write(dev, 0x0062, 0x0007); - b43_radio_init2050(dev); - b43_lo_g_measure(dev); -- if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI) { -+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI) { - b43_calc_nrssi_slope(dev); - b43_calc_nrssi_threshold(dev); - } -@@ -1386,7 +1386,7 @@ static void b43_calc_loopback_gain(struc - b43_phy_write(dev, B43_PHY_RFOVERVAL, - b43_phy_read(dev, B43_PHY_RFOVERVAL) & 0xCFFF); - -- if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_EXTLNA) { -+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_EXTLNA) { - if (phy->rev >= 7) { - b43_phy_write(dev, B43_PHY_RFOVER, - b43_phy_read(dev, B43_PHY_RFOVER) -@@ -1553,7 +1553,7 @@ static void b43_phy_initg(struct b43_wld - & 0x0FFF) | (phy->lo_control-> - tx_bias << 12)); - } -- if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_PACTRL) -+ if (dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_PACTRL) - b43_phy_write(dev, B43_PHY_CCK(0x2E), 0x8075); - else - b43_phy_write(dev, B43_PHY_CCK(0x2E), 0x807F); -@@ -1567,7 +1567,7 @@ static void b43_phy_initg(struct b43_wld - b43_phy_write(dev, B43_PHY_LO_MASK, 0x8078); - } - -- if (!(dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI)) { -+ if (!(dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI)) { - /* The specs state to update the NRSSI LT with - * the value 0x7FFFFFFF here. I think that is some weird - * compiler optimization in the original driver. -@@ -1776,15 +1776,15 @@ void b43_phy_xmitpower(struct b43_wldev - estimated_pwr = - b43_phy_estimate_power_out(dev, average); - -- max_pwr = dev->dev->bus->sprom.maxpwr_bg; -- if ((dev->dev->bus->sprom.boardflags_lo -+ max_pwr = dev->dev->bus->sprom.r1.maxpwr_bg; -+ if ((dev->dev->bus->sprom.r1.boardflags_lo - & B43_BFL_PACTRL) && (phy->type == B43_PHYTYPE_G)) - max_pwr -= 0x3; - if (unlikely(max_pwr <= 0)) { - b43warn(dev->wl, - "Invalid max-TX-power value in SPROM.\n"); - max_pwr = 60; /* fake it */ -- dev->dev->bus->sprom.maxpwr_bg = max_pwr; -+ dev->dev->bus->sprom.r1.maxpwr_bg = max_pwr; - } - - /*TODO: -@@ -1842,7 +1842,7 @@ void b43_phy_xmitpower(struct b43_wldev - B43_TXCTL_TXMIX; - rfatt += 2; - bbatt += 2; -- } else if (dev->dev->bus->sprom. -+ } else if (dev->dev->bus->sprom.r1. - boardflags_lo & - B43_BFL_PACTRL) { - bbatt += 4 * (rfatt - 2); -@@ -1921,13 +1921,13 @@ int b43_phy_init_tssi2dbm_table(struct b - s8 *dyn_tssi2dbm; - - if (phy->type == B43_PHYTYPE_A) { -- pab0 = (s16) (dev->dev->bus->sprom.pa1b0); -- pab1 = (s16) (dev->dev->bus->sprom.pa1b1); -- pab2 = (s16) (dev->dev->bus->sprom.pa1b2); -+ pab0 = (s16) (dev->dev->bus->sprom.r1.pa1b0); -+ pab1 = (s16) (dev->dev->bus->sprom.r1.pa1b1); -+ pab2 = (s16) (dev->dev->bus->sprom.r1.pa1b2); - } else { -- pab0 = (s16) (dev->dev->bus->sprom.pa0b0); -- pab1 = (s16) (dev->dev->bus->sprom.pa0b1); -- pab2 = (s16) (dev->dev->bus->sprom.pa0b2); -+ pab0 = (s16) (dev->dev->bus->sprom.r1.pa0b0); -+ pab1 = (s16) (dev->dev->bus->sprom.r1.pa0b1); -+ pab2 = (s16) (dev->dev->bus->sprom.r1.pa0b2); - } - - if ((dev->dev->bus->chip_id == 0x4301) && (phy->radio_ver != 0x2050)) { -@@ -1940,17 +1940,17 @@ int b43_phy_init_tssi2dbm_table(struct b - pab0 != -1 && pab1 != -1 && pab2 != -1) { - /* The pabX values are set in SPROM. Use them. */ - if (phy->type == B43_PHYTYPE_A) { -- if ((s8) dev->dev->bus->sprom.itssi_a != 0 && -- (s8) dev->dev->bus->sprom.itssi_a != -1) -+ if ((s8) dev->dev->bus->sprom.r1.itssi_a != 0 && -+ (s8) dev->dev->bus->sprom.r1.itssi_a != -1) - phy->tgt_idle_tssi = -- (s8) (dev->dev->bus->sprom.itssi_a); -+ (s8) (dev->dev->bus->sprom.r1.itssi_a); - else - phy->tgt_idle_tssi = 62; - } else { -- if ((s8) dev->dev->bus->sprom.itssi_bg != 0 && -- (s8) dev->dev->bus->sprom.itssi_bg != -1) -+ if ((s8) dev->dev->bus->sprom.r1.itssi_bg != 0 && -+ (s8) dev->dev->bus->sprom.r1.itssi_bg != -1) - phy->tgt_idle_tssi = -- (s8) (dev->dev->bus->sprom.itssi_bg); -+ (s8) (dev->dev->bus->sprom.r1.itssi_bg); - else - phy->tgt_idle_tssi = 62; - } -@@ -2894,7 +2894,7 @@ void b43_calc_nrssi_threshold(struct b43 - if (phy->radio_ver != 0x2050) - return; - if (! -- (dev->dev->bus->sprom. -+ (dev->dev->bus->sprom.r1. - boardflags_lo & B43_BFL_RSSI)) - return; - -@@ -2925,7 +2925,7 @@ void b43_calc_nrssi_threshold(struct b43 - } - case B43_PHYTYPE_G: - if (!phy->gmode || -- !(dev->dev->bus->sprom.boardflags_lo & B43_BFL_RSSI)) { -+ !(dev->dev->bus->sprom.r1.boardflags_lo & B43_BFL_RSSI)) { - tmp16 = b43_nrssi_hw_read(dev, 0x20); - if (tmp16 >= 0x20) - tmp16 -= 0x40; -@@ -3447,7 +3447,7 @@ static u16 radio2050_rfover_val(struct b - } - - if ((phy->rev < 7) || -- !(sprom->boardflags_lo & B43_BFL_EXTLNA)) { -+ !(sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) { - if (phy_register == B43_PHY_RFOVER) { - return 0x1B3; - } else if (phy_register == B43_PHY_RFOVERVAL) { -@@ -3487,7 +3487,7 @@ static u16 radio2050_rfover_val(struct b - } - } else { - if ((phy->rev < 7) || -- !(sprom->boardflags_lo & B43_BFL_EXTLNA)) { -+ !(sprom->r1.boardflags_lo & B43_BFL_EXTLNA)) { - if (phy_register == B43_PHY_RFOVER) { - return 0x1B3; - } else if (phy_register == B43_PHY_RFOVERVAL) { -@@ -3979,7 +3979,7 @@ int b43_radio_selectchannel(struct b43_w - b43_write16(dev, B43_MMIO_CHANNEL, channel2freq_bg(channel)); - - if (channel == 14) { -- if (dev->dev->bus->sprom.country_code == -+ if (dev->dev->bus->sprom.r1.country_code == - SSB_SPROM1CCODE_JAPAN) - b43_hf_write(dev, - b43_hf_read(dev) & ~B43_HF_ACPR); -Index: b43/wa.c -=================================================================== ---- b43.orig/wa.c 2008-02-06 00:55:14.000000000 +0100 -+++ b43/wa.c 2008-02-15 22:50:54.000000000 +0100 -@@ -535,7 +535,7 @@ static void b43_wa_boards_g(struct b43_w - } else { - b43_ofdmtab_write16(dev, B43_OFDMTAB_GAINX, 1, 0x0002); - b43_ofdmtab_write16(dev, B43_OFDMTAB_GAINX, 2, 0x0001); -- if ((bus->sprom.boardflags_lo & B43_BFL_EXTLNA) && -+ if ((bus->sprom.r1.boardflags_lo & B43_BFL_EXTLNA) && - (phy->rev >= 7)) { - b43_phy_write(dev, B43_PHY_EXTG(0x11), - b43_phy_read(dev, B43_PHY_EXTG(0x11)) & 0xF7FF); -@@ -548,7 +548,7 @@ static void b43_wa_boards_g(struct b43_w - } - } - } -- if (bus->sprom.boardflags_lo & B43_BFL_FEM) { -+ if (bus->sprom.r1.boardflags_lo & B43_BFL_FEM) { - b43_phy_write(dev, B43_PHY_GTABCTL, 0x3120); - b43_phy_write(dev, B43_PHY_GTABDATA, 0xC480); - } -Index: b43/xmit.c -=================================================================== ---- b43.orig/xmit.c 2008-02-06 00:55:14.000000000 +0100 -+++ b43/xmit.c 2008-02-15 22:49:37.000000000 +0100 -@@ -444,7 +444,7 @@ static s8 b43_rssi_postprocess(struct b4 - else - tmp -= 3; - } else { -- if (dev->dev->bus->sprom. -+ if (dev->dev->bus->sprom.r1. - boardflags_lo & B43_BFL_RSSI) { - if (in_rssi > 63) - in_rssi = 63; diff --git a/target/linux/brcm47xx/files/arch/mips/bcm947xx/setup.c b/target/linux/brcm47xx/files/arch/mips/bcm947xx/setup.c index 008634a..2fcf684 100644 --- a/target/linux/brcm47xx/files/arch/mips/bcm947xx/setup.c +++ b/target/linux/brcm47xx/files/arch/mips/bcm947xx/setup.c @@ -94,49 +94,53 @@ static void bcm47xx_fill_sprom(struct ssb_sprom *sprom) sprom->revision = 1; if ((s = nvram_get("il0macaddr"))) - e_aton(s, sprom->r1.il0mac); + e_aton(s, sprom->il0mac); if ((s = nvram_get("et0macaddr"))) - e_aton(s, sprom->r1.et0mac); + e_aton(s, sprom->et0mac); if ((s = nvram_get("et1macaddr"))) - e_aton(s, sprom->r1.et1mac); + e_aton(s, sprom->et1mac); if ((s = nvram_get("et0phyaddr"))) - sprom->r1.et0phyaddr = simple_strtoul(s, NULL, 0); + sprom->et0phyaddr = simple_strtoul(s, NULL, 0); if ((s = nvram_get("et1phyaddr"))) - sprom->r1.et1phyaddr = simple_strtoul(s, NULL, 0); + sprom->et1phyaddr = simple_strtoul(s, NULL, 0); if ((s = nvram_get("et0mdcport"))) - sprom->r1.et0mdcport = !!simple_strtoul(s, NULL, 10); + sprom->et0mdcport = !!simple_strtoul(s, NULL, 10); if ((s = nvram_get("et1mdcport"))) - sprom->r1.et1mdcport = !!simple_strtoul(s, NULL, 10); + sprom->et1mdcport = !!simple_strtoul(s, NULL, 10); if ((s = nvram_get("pa0b0"))) - sprom->r1.pa0b0 = simple_strtoul(s, NULL, 0); + sprom->pa0b0 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa0b1"))) - sprom->r1.pa0b1 = simple_strtoul(s, NULL, 0); + sprom->pa0b1 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa0b2"))) - sprom->r1.pa0b2 = simple_strtoul(s, NULL, 0); + sprom->pa0b2 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa1b0"))) - sprom->r1.pa1b0 = simple_strtoul(s, NULL, 0); + sprom->pa1b0 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa1b1"))) - sprom->r1.pa1b1 = simple_strtoul(s, NULL, 0); + sprom->pa1b1 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa1b2"))) - sprom->r1.pa1b2 = simple_strtoul(s, NULL, 0); + sprom->pa1b2 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("wl0gpio0"))) - sprom->r1.gpio0 = simple_strtoul(s, NULL, 0); + sprom->gpio0 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("wl0gpio1"))) - sprom->r1.gpio1 = simple_strtoul(s, NULL, 0); + sprom->gpio1 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("wl0gpio2"))) - sprom->r1.gpio2 = simple_strtoul(s, NULL, 0); + sprom->gpio2 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("wl0gpio3"))) - sprom->r1.gpio3 = simple_strtoul(s, NULL, 0); + sprom->gpio3 = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa0maxpwr"))) - sprom->r1.maxpwr_bg = simple_strtoul(s, NULL, 0); + sprom->maxpwr_bg = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa1maxpwr"))) - sprom->r1.maxpwr_a = simple_strtoul(s, NULL, 0); + sprom->maxpwr_a = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa0itssit"))) - sprom->r1.itssi_bg = simple_strtoul(s, NULL, 0); + sprom->itssi_bg = simple_strtoul(s, NULL, 0); if ((s = nvram_get("pa1itssit"))) - sprom->r1.itssi_a = simple_strtoul(s, NULL, 0); + sprom->itssi_a = simple_strtoul(s, NULL, 0); + sprom->boardflags_lo = 0; if ((s = nvram_get("boardflags"))) - sprom->r1.boardflags_lo = simple_strtoul(s, NULL, 0); + sprom->boardflags_lo = simple_strtoul(s, NULL, 0); + sprom->boardflags_hi = 0; + if ((s = nvram_get("boardflags2"))) + sprom->boardflags_hi = simple_strtoul(s, NULL, 0); } static int bcm47xx_get_invariants(struct ssb_bus *bus, struct ssb_init_invariants *iv) diff --git a/target/linux/brcm47xx/patches-2.6.23/120-b44_ssb_support.patch b/target/linux/brcm47xx/patches-2.6.23/120-b44_ssb_support.patch index 06865cf..29125c6 100644 --- a/target/linux/brcm47xx/patches-2.6.23/120-b44_ssb_support.patch +++ b/target/linux/brcm47xx/patches-2.6.23/120-b44_ssb_support.patch @@ -1,7 +1,7 @@ -Index: linux-2.6.23/drivers/net/b44.c +Index: linux-2.6.23.16/drivers/net/b44.c =================================================================== ---- linux-2.6.23.orig/drivers/net/b44.c 2007-10-13 10:58:27.872607266 +0200 -+++ linux-2.6.23/drivers/net/b44.c 2007-10-13 11:00:46.916530927 +0200 +--- linux-2.6.23.16.orig/drivers/net/b44.c 2008-02-19 01:35:58.000000000 +0100 ++++ linux-2.6.23.16/drivers/net/b44.c 2008-02-19 01:37:04.000000000 +0100 @@ -1,7 +1,9 @@ -/* b44.c: Broadcom 4400 device driver. +/* b44.c: Broadcom 4400/47xx device driver. @@ -39,7 +39,7 @@ Index: linux-2.6.23/drivers/net/b44.c MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_MODULE_VERSION); -@@ -96,18 +100,11 @@ +@@ -96,18 +100,11 @@ static int b44_debug = -1; /* -1 == use module_param(b44_debug, int, 0); MODULE_PARM_DESC(b44_debug, "B44 bitmapped debugging message enable value"); @@ -61,7 +61,7 @@ Index: linux-2.6.23/drivers/net/b44.c static void b44_halt(struct b44 *); static void b44_init_rings(struct b44 *); -@@ -119,6 +116,7 @@ +@@ -119,6 +116,7 @@ static void b44_init_hw(struct b44 *, in static int dma_desc_align_mask; static int dma_desc_sync_size; @@ -69,7 +69,7 @@ Index: linux-2.6.23/drivers/net/b44.c static const char b44_gstrings[][ETH_GSTRING_LEN] = { #define _B44(x...) # x, -@@ -126,35 +124,24 @@ +@@ -126,35 +124,24 @@ B44_STAT_REG_DECLARE #undef _B44 }; @@ -123,7 +123,7 @@ Index: linux-2.6.23/drivers/net/b44.c } static int b44_wait_bit(struct b44 *bp, unsigned long reg, -@@ -182,117 +169,29 @@ +@@ -182,117 +169,29 @@ static int b44_wait_bit(struct b44 *bp, return 0; } @@ -254,7 +254,7 @@ Index: linux-2.6.23/drivers/net/b44.c { u32 val; -@@ -328,14 +227,14 @@ +@@ -328,14 +227,14 @@ static void b44_enable_ints(struct b44 * bw32(bp, B44_IMASK, bp->imask); } @@ -271,7 +271,7 @@ Index: linux-2.6.23/drivers/net/b44.c (reg << MDIO_DATA_RA_SHIFT) | (MDIO_TA_VALID << MDIO_DATA_TA_SHIFT))); err = b44_wait_bit(bp, B44_EMAC_ISTAT, EMAC_INT_MII, 100, 0); -@@ -344,18 +243,34 @@ +@@ -344,18 +243,34 @@ static int b44_readphy(struct b44 *bp, i return err; } @@ -308,7 +308,7 @@ Index: linux-2.6.23/drivers/net/b44.c /* miilib interface */ /* FIXME FIXME: phy_id is ignored, bp->phy_addr use is unconditional * due to code existing before miilib use was added to this driver. -@@ -384,6 +299,8 @@ +@@ -384,6 +299,8 @@ static int b44_phy_reset(struct b44 *bp) u32 val; int err; @@ -317,7 +317,7 @@ Index: linux-2.6.23/drivers/net/b44.c err = b44_writephy(bp, MII_BMCR, BMCR_RESET); if (err) return err; -@@ -442,11 +359,27 @@ +@@ -442,11 +359,27 @@ static void b44_set_flow_ctrl(struct b44 __b44_set_flow_ctrl(bp, pause_enab); } @@ -345,7 +345,7 @@ Index: linux-2.6.23/drivers/net/b44.c if ((err = b44_readphy(bp, B44_MII_ALEDCTRL, &val)) != 0) goto out; if ((err = b44_writephy(bp, B44_MII_ALEDCTRL, -@@ -542,6 +475,19 @@ +@@ -542,6 +475,19 @@ static void b44_check_phy(struct b44 *bp { u32 bmsr, aux; @@ -365,7 +365,7 @@ Index: linux-2.6.23/drivers/net/b44.c if (!b44_readphy(bp, MII_BMSR, &bmsr) && !b44_readphy(bp, B44_MII_AUXCTRL, &aux) && (bmsr != 0xffff)) { -@@ -617,10 +563,10 @@ +@@ -617,10 +563,10 @@ static void b44_tx(struct b44 *bp) BUG_ON(skb == NULL); @@ -378,7 +378,7 @@ Index: linux-2.6.23/drivers/net/b44.c rp->skb = NULL; dev_kfree_skb_irq(skb); } -@@ -657,9 +603,9 @@ +@@ -657,9 +603,9 @@ static int b44_alloc_rx_skb(struct b44 * if (skb == NULL) return -ENOMEM; @@ -390,7 +390,7 @@ Index: linux-2.6.23/drivers/net/b44.c /* Hardware bug work-around, the chip is unable to do PCI DMA to/from anything above 1GB :-( */ -@@ -667,18 +613,18 @@ +@@ -667,18 +613,18 @@ static int b44_alloc_rx_skb(struct b44 * mapping + RX_PKT_BUF_SZ > DMA_30BIT_MASK) { /* Sigh... */ if (!dma_mapping_error(mapping)) @@ -413,7 +413,7 @@ Index: linux-2.6.23/drivers/net/b44.c dev_kfree_skb_any(skb); return -ENOMEM; } -@@ -705,9 +651,9 @@ +@@ -705,9 +651,9 @@ static int b44_alloc_rx_skb(struct b44 * dp->addr = cpu_to_le32((u32) mapping + RX_PKT_OFFSET + bp->dma_offset); if (bp->flags & B44_FLAG_RX_RING_HACK) @@ -426,7 +426,7 @@ Index: linux-2.6.23/drivers/net/b44.c return RX_PKT_BUF_SZ; } -@@ -734,9 +680,9 @@ +@@ -734,9 +680,9 @@ static void b44_recycle_rx(struct b44 *b pci_unmap_addr(src_map, mapping)); if (bp->flags & B44_FLAG_RX_RING_HACK) @@ -439,7 +439,7 @@ Index: linux-2.6.23/drivers/net/b44.c ctrl = src_desc->ctrl; if (dest_idx == (B44_RX_RING_SIZE - 1)) -@@ -750,13 +696,13 @@ +@@ -750,13 +696,13 @@ static void b44_recycle_rx(struct b44 *b src_map->skb = NULL; if (bp->flags & B44_FLAG_RX_RING_HACK) @@ -458,7 +458,7 @@ Index: linux-2.6.23/drivers/net/b44.c } static int b44_rx(struct b44 *bp, int budget) -@@ -776,9 +722,9 @@ +@@ -776,9 +722,9 @@ static int b44_rx(struct b44 *bp, int bu struct rx_header *rh; u16 len; @@ -470,7 +470,7 @@ Index: linux-2.6.23/drivers/net/b44.c rh = (struct rx_header *) skb->data; len = le16_to_cpu(rh->len); if ((len > (RX_PKT_BUF_SZ - RX_PKT_OFFSET)) || -@@ -810,8 +756,8 @@ +@@ -810,8 +756,8 @@ static int b44_rx(struct b44 *bp, int bu skb_size = b44_alloc_rx_skb(bp, cons, bp->rx_prod); if (skb_size < 0) goto drop_it; @@ -481,7 +481,7 @@ Index: linux-2.6.23/drivers/net/b44.c /* Leave out rx_header */ skb_put(skb, len + RX_PKT_OFFSET); skb_pull(skb, RX_PKT_OFFSET); -@@ -982,24 +928,24 @@ +@@ -982,24 +928,24 @@ static int b44_start_xmit(struct sk_buff goto err_out; } @@ -512,7 +512,7 @@ Index: linux-2.6.23/drivers/net/b44.c dev_kfree_skb_any(bounce_skb); goto err_out; } -@@ -1022,9 +968,9 @@ +@@ -1022,9 +968,9 @@ static int b44_start_xmit(struct sk_buff bp->tx_ring[entry].addr = cpu_to_le32((u32) mapping+bp->dma_offset); if (bp->flags & B44_FLAG_TX_RING_HACK) @@ -525,7 +525,7 @@ Index: linux-2.6.23/drivers/net/b44.c entry = NEXT_TX(entry); -@@ -1097,10 +1043,10 @@ +@@ -1097,10 +1043,10 @@ static void b44_free_rings(struct b44 *b if (rp->skb == NULL) continue; @@ -538,7 +538,7 @@ Index: linux-2.6.23/drivers/net/b44.c dev_kfree_skb_any(rp->skb); rp->skb = NULL; } -@@ -1111,10 +1057,10 @@ +@@ -1111,10 +1057,10 @@ static void b44_free_rings(struct b44 *b if (rp->skb == NULL) continue; @@ -551,7 +551,7 @@ Index: linux-2.6.23/drivers/net/b44.c dev_kfree_skb_any(rp->skb); rp->skb = NULL; } -@@ -1136,14 +1082,14 @@ +@@ -1136,14 +1082,14 @@ static void b44_init_rings(struct b44 *b memset(bp->tx_ring, 0, B44_TX_RING_BYTES); if (bp->flags & B44_FLAG_RX_RING_HACK) @@ -572,7 +572,7 @@ Index: linux-2.6.23/drivers/net/b44.c for (i = 0; i < bp->rx_pending; i++) { if (b44_alloc_rx_skb(bp, -1, i) < 0) -@@ -1163,24 +1109,24 @@ +@@ -1163,24 +1109,24 @@ static void b44_free_consistent(struct b bp->tx_buffers = NULL; if (bp->rx_ring) { if (bp->flags & B44_FLAG_RX_RING_HACK) { @@ -605,7 +605,7 @@ Index: linux-2.6.23/drivers/net/b44.c bp->tx_ring, bp->tx_ring_dma); bp->tx_ring = NULL; bp->flags &= ~B44_FLAG_TX_RING_HACK; -@@ -1206,7 +1152,7 @@ +@@ -1206,7 +1152,7 @@ static int b44_alloc_consistent(struct b goto out_err; size = DMA_TABLE_BYTES; @@ -614,7 +614,7 @@ Index: linux-2.6.23/drivers/net/b44.c if (!bp->rx_ring) { /* Allocation may have failed due to pci_alloc_consistent insisting on use of GFP_DMA, which is more restrictive -@@ -1218,9 +1164,9 @@ +@@ -1218,9 +1164,9 @@ static int b44_alloc_consistent(struct b if (!rx_ring) goto out_err; @@ -627,7 +627,7 @@ Index: linux-2.6.23/drivers/net/b44.c if (dma_mapping_error(rx_ring_dma) || rx_ring_dma + size > DMA_30BIT_MASK) { -@@ -1233,9 +1179,9 @@ +@@ -1233,9 +1179,9 @@ static int b44_alloc_consistent(struct b bp->flags |= B44_FLAG_RX_RING_HACK; } @@ -639,7 +639,7 @@ Index: linux-2.6.23/drivers/net/b44.c insisting on use of GFP_DMA, which is more restrictive than necessary... */ struct dma_desc *tx_ring; -@@ -1245,9 +1191,9 @@ +@@ -1245,9 +1191,9 @@ static int b44_alloc_consistent(struct b if (!tx_ring) goto out_err; @@ -652,7 +652,7 @@ Index: linux-2.6.23/drivers/net/b44.c if (dma_mapping_error(tx_ring_dma) || tx_ring_dma + size > DMA_30BIT_MASK) { -@@ -1282,7 +1228,9 @@ +@@ -1282,7 +1228,9 @@ static void b44_clear_stats(struct b44 * /* bp->lock is held. */ static void b44_chip_reset(struct b44 *bp) { @@ -663,7 +663,7 @@ Index: linux-2.6.23/drivers/net/b44.c bw32(bp, B44_RCV_LAZY, 0); bw32(bp, B44_ENET_CTRL, ENET_CTRL_DISABLE); b44_wait_bit(bp, B44_ENET_CTRL, ENET_CTRL_DISABLE, 200, 1); -@@ -1294,19 +1242,23 @@ +@@ -1294,19 +1242,24 @@ static void b44_chip_reset(struct b44 *b } bw32(bp, B44_DMARX_CTRL, 0); bp->rx_prod = bp->rx_cons = 0; @@ -687,6 +687,7 @@ Index: linux-2.6.23/drivers/net/b44.c + & MDIO_CTRL_MAXF_MASK))); + break; + case SSB_BUSTYPE_PCI: ++ case SSB_BUSTYPE_PCMCIA: + bw32(bp, B44_MDIO_CTRL, (MDIO_CTRL_PREAMBLE | (0x0d & MDIO_CTRL_MAXF_MASK))); + break; @@ -695,7 +696,7 @@ Index: linux-2.6.23/drivers/net/b44.c br32(bp, B44_MDIO_CTRL); if (!(br32(bp, B44_DEVCTRL) & DEVCTRL_IPP)) { -@@ -1349,6 +1301,7 @@ +@@ -1349,6 +1302,7 @@ static int b44_set_mac_addr(struct net_d { struct b44 *bp = netdev_priv(dev); struct sockaddr *addr = p; @@ -703,7 +704,7 @@ Index: linux-2.6.23/drivers/net/b44.c if (netif_running(dev)) return -EBUSY; -@@ -1359,7 +1312,11 @@ +@@ -1359,7 +1313,11 @@ static int b44_set_mac_addr(struct net_d memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); spin_lock_irq(&bp->lock); @@ -716,7 +717,7 @@ Index: linux-2.6.23/drivers/net/b44.c spin_unlock_irq(&bp->lock); return 0; -@@ -1445,18 +1402,6 @@ +@@ -1445,18 +1403,6 @@ out: return err; } @@ -735,7 +736,7 @@ Index: linux-2.6.23/drivers/net/b44.c #ifdef CONFIG_NET_POLL_CONTROLLER /* * Polling receive - used by netconsole and other diagnostic tools -@@ -1570,7 +1515,6 @@ +@@ -1570,7 +1516,6 @@ static void b44_setup_pseudo_magicp(stru static void b44_setup_wol(struct b44 *bp) { u32 val; @@ -743,7 +744,7 @@ Index: linux-2.6.23/drivers/net/b44.c bw32(bp, B44_RXCONFIG, RXCONFIG_ALLMULTI); -@@ -1594,13 +1538,6 @@ +@@ -1594,13 +1539,6 @@ static void b44_setup_wol(struct b44 *bp } else { b44_setup_pseudo_magicp(bp); } @@ -757,7 +758,7 @@ Index: linux-2.6.23/drivers/net/b44.c } static int b44_close(struct net_device *dev) -@@ -1700,7 +1637,7 @@ +@@ -1700,7 +1638,7 @@ static void __b44_set_rx_mode(struct net val = br32(bp, B44_RXCONFIG); val &= ~(RXCONFIG_PROMISC | RXCONFIG_ALLMULTI); @@ -766,7 +767,7 @@ Index: linux-2.6.23/drivers/net/b44.c val |= RXCONFIG_PROMISC; bw32(bp, B44_RXCONFIG, val); } else { -@@ -1747,12 +1684,8 @@ +@@ -1747,12 +1685,8 @@ static void b44_set_msglevel(struct net_ static void b44_get_drvinfo (struct net_device *dev, struct ethtool_drvinfo *info) { @@ -779,7 +780,7 @@ Index: linux-2.6.23/drivers/net/b44.c } static int b44_nway_reset(struct net_device *dev) -@@ -2035,6 +1968,245 @@ +@@ -2035,6 +1969,245 @@ static const struct ethtool_ops b44_etht .get_ethtool_stats = b44_get_ethtool_stats, }; @@ -1025,7 +1026,7 @@ Index: linux-2.6.23/drivers/net/b44.c static int b44_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) { struct mii_ioctl_data *data = if_mii(ifr); -@@ -2044,40 +2216,64 @@ +@@ -2044,40 +2217,64 @@ static int b44_ioctl(struct net_device * if (!netif_running(dev)) goto out; @@ -1102,12 +1103,12 @@ Index: linux-2.6.23/drivers/net/b44.c - bp->dev->dev_addr[5] = eeprom[82]; + switch (instance) { + case 1: -+ addr = sdev->bus->sprom.r1.et0mac; -+ bp->phy_addr = sdev->bus->sprom.r1.et0phyaddr; ++ addr = sdev->bus->sprom.et0mac; ++ bp->phy_addr = sdev->bus->sprom.et0phyaddr; + break; + default: -+ addr = sdev->bus->sprom.r1.et1mac; -+ bp->phy_addr = sdev->bus->sprom.r1.et1phyaddr; ++ addr = sdev->bus->sprom.et1mac; ++ bp->phy_addr = sdev->bus->sprom.et1phyaddr; + break; + } + @@ -1115,7 +1116,7 @@ Index: linux-2.6.23/drivers/net/b44.c if (!is_valid_ether_addr(&bp->dev->dev_addr[0])){ printk(KERN_ERR PFX "Invalid MAC address found in EEPROM\n"); -@@ -2086,103 +2282,52 @@ +@@ -2086,103 +2283,52 @@ static int __devinit b44_get_invariants( memcpy(bp->dev->perm_addr, bp->dev->dev_addr, bp->dev->addr_len); @@ -1228,7 +1229,7 @@ Index: linux-2.6.23/drivers/net/b44.c bp->rx_pending = B44_DEF_RX_RING_PENDING; bp->tx_pending = B44_DEF_TX_RING_PENDING; -@@ -2201,16 +2346,16 @@ +@@ -2201,16 +2347,16 @@ static int __devinit b44_init_one(struct dev->poll_controller = b44_poll_controller; #endif dev->change_mtu = b44_change_mtu; @@ -1248,7 +1249,7 @@ Index: linux-2.6.23/drivers/net/b44.c } bp->mii_if.dev = dev; -@@ -2229,61 +2374,52 @@ +@@ -2229,61 +2375,52 @@ static int __devinit b44_init_one(struct err = register_netdev(dev); if (err) { @@ -1326,7 +1327,7 @@ Index: linux-2.6.23/drivers/net/b44.c del_timer_sync(&bp->timer); -@@ -2301,33 +2437,22 @@ +@@ -2301,33 +2438,22 @@ static int b44_suspend(struct pci_dev *p b44_init_hw(bp, B44_PARTIAL_RESET); b44_setup_wol(bp); } @@ -1363,7 +1364,7 @@ Index: linux-2.6.23/drivers/net/b44.c return rc; } -@@ -2346,29 +2471,31 @@ +@@ -2346,29 +2472,31 @@ static int b44_resume(struct pci_dev *pd return 0; } @@ -1401,10 +1402,10 @@ Index: linux-2.6.23/drivers/net/b44.c } module_init(b44_init); -Index: linux-2.6.23/drivers/net/b44.h +Index: linux-2.6.23.16/drivers/net/b44.h =================================================================== ---- linux-2.6.23.orig/drivers/net/b44.h 2007-10-13 10:58:27.880607722 +0200 -+++ linux-2.6.23/drivers/net/b44.h 2007-10-13 11:00:46.904530245 +0200 +--- linux-2.6.23.16.orig/drivers/net/b44.h 2008-02-19 01:35:58.000000000 +0100 ++++ linux-2.6.23.16/drivers/net/b44.h 2008-02-19 01:36:00.000000000 +0100 @@ -129,6 +129,7 @@ #define RXCONFIG_FLOW 0x00000020 /* Flow Control Enable */ #define RXCONFIG_FLOW_ACCEPT 0x00000040 /* Accept Unicast Flow Control Frame */ @@ -1492,7 +1493,7 @@ Index: linux-2.6.23/drivers/net/b44.h /* 4400 PHY registers */ #define B44_MII_AUXCTRL 24 /* Auxiliary Control */ -@@ -346,10 +281,12 @@ +@@ -346,10 +281,12 @@ struct rx_header { struct ring_info { struct sk_buff *skb; @@ -1506,7 +1507,7 @@ Index: linux-2.6.23/drivers/net/b44.h #define B44_STAT_REG_DECLARE \ _B44(tx_good_octets) \ -@@ -425,9 +362,10 @@ +@@ -425,9 +362,10 @@ struct b44 { u32 dma_offset; u32 flags; @@ -1518,7 +1519,7 @@ Index: linux-2.6.23/drivers/net/b44.h #define B44_FLAG_PAUSE_AUTO 0x00008000 #define B44_FLAG_FULL_DUPLEX 0x00010000 #define B44_FLAG_100_BASE_T 0x00020000 -@@ -450,8 +388,7 @@ +@@ -450,8 +388,7 @@ struct b44 { struct net_device_stats stats; struct b44_hw_stats hw_stats; @@ -1528,11 +1529,11 @@ Index: linux-2.6.23/drivers/net/b44.h struct net_device *dev; dma_addr_t rx_ring_dma, tx_ring_dma; -Index: linux-2.6.23/drivers/net/Kconfig +Index: linux-2.6.23.16/drivers/net/Kconfig =================================================================== ---- linux-2.6.23.orig/drivers/net/Kconfig 2007-10-13 10:58:27.888608180 +0200 -+++ linux-2.6.23/drivers/net/Kconfig 2007-10-13 11:00:46.912530699 +0200 -@@ -1577,7 +1577,7 @@ +--- linux-2.6.23.16.orig/drivers/net/Kconfig 2008-02-19 01:35:58.000000000 +0100 ++++ linux-2.6.23.16/drivers/net/Kconfig 2008-02-19 01:36:00.000000000 +0100 +@@ -1577,7 +1577,7 @@ config APRICOT config B44 tristate "Broadcom 4400 ethernet support" diff --git a/target/linux/brcm47xx/patches-2.6.23/210-ssb_fixes.patch b/target/linux/brcm47xx/patches-2.6.23/210-ssb_fixes.patch index 3b87a8c..ce3a007 100644 --- a/target/linux/brcm47xx/patches-2.6.23/210-ssb_fixes.patch +++ b/target/linux/brcm47xx/patches-2.6.23/210-ssb_fixes.patch @@ -1,18 +1,18 @@ -Index: linux-2.6.23/drivers/ssb/driver_mipscore.c +Index: linux-2.6.23.16/drivers/ssb/driver_mipscore.c =================================================================== ---- linux-2.6.23.orig/drivers/ssb/driver_mipscore.c 2007-10-14 04:32:45.793470742 +0200 -+++ linux-2.6.23/drivers/ssb/driver_mipscore.c 2007-10-14 04:33:25.155713862 +0200 -@@ -222,3 +222,5 @@ +--- linux-2.6.23.16.orig/drivers/ssb/driver_mipscore.c 2008-02-19 01:35:53.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/driver_mipscore.c 2008-02-19 02:01:16.000000000 +0100 +@@ -222,3 +222,5 @@ void ssb_mipscore_init(struct ssb_mipsco ssb_mips_serial_init(mcore); ssb_mips_flash_detect(mcore); } + +EXPORT_SYMBOL(ssb_mips_irq); -Index: linux-2.6.23/include/linux/ssb/ssb_driver_chipcommon.h +Index: linux-2.6.23.16/include/linux/ssb/ssb_driver_chipcommon.h =================================================================== ---- linux-2.6.23.orig/include/linux/ssb/ssb_driver_chipcommon.h 2007-10-14 04:32:45.817472111 +0200 -+++ linux-2.6.23/include/linux/ssb/ssb_driver_chipcommon.h 2007-10-14 04:33:25.159714091 +0200 -@@ -382,11 +382,45 @@ +--- linux-2.6.23.16.orig/include/linux/ssb/ssb_driver_chipcommon.h 2008-02-19 01:35:53.000000000 +0100 ++++ linux-2.6.23.16/include/linux/ssb/ssb_driver_chipcommon.h 2008-02-19 02:01:10.000000000 +0100 +@@ -382,11 +382,45 @@ extern void ssb_chipco_set_clockmode(str extern void ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks); @@ -61,10 +61,10 @@ Index: linux-2.6.23/include/linux/ssb/ssb_driver_chipcommon.h #ifdef CONFIG_SSB_SERIAL extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc, -Index: linux-2.6.23/include/linux/ssb/ssb_driver_extif.h +Index: linux-2.6.23.16/include/linux/ssb/ssb_driver_extif.h =================================================================== ---- linux-2.6.23.orig/include/linux/ssb/ssb_driver_extif.h 2007-10-14 04:32:45.821472339 +0200 -+++ linux-2.6.23/include/linux/ssb/ssb_driver_extif.h 2007-10-14 04:33:25.167714544 +0200 +--- linux-2.6.23.16.orig/include/linux/ssb/ssb_driver_extif.h 2008-02-19 01:35:53.000000000 +0100 ++++ linux-2.6.23.16/include/linux/ssb/ssb_driver_extif.h 2008-02-19 01:39:40.000000000 +0100 @@ -153,7 +153,6 @@ #define SSB_EXTIF_WATCHDOG_CLK 48000000 /* Hz */ @@ -73,7 +73,7 @@ Index: linux-2.6.23/include/linux/ssb/ssb_driver_extif.h #ifdef CONFIG_SSB_DRIVER_EXTIF struct ssb_extif { -@@ -171,17 +170,42 @@ +@@ -171,17 +170,42 @@ extern void ssb_extif_get_clockcontrol(s extern void ssb_extif_timing_init(struct ssb_extif *extif, unsigned long ns); @@ -122,11 +122,11 @@ Index: linux-2.6.23/include/linux/ssb/ssb_driver_extif.h #else /* CONFIG_SSB_DRIVER_EXTIF */ /* extif disabled */ -Index: linux-2.6.23/include/linux/ssb/ssb.h +Index: linux-2.6.23.16/include/linux/ssb/ssb.h =================================================================== ---- linux-2.6.23.orig/include/linux/ssb/ssb.h 2007-10-14 04:32:45.833473010 +0200 -+++ linux-2.6.23/include/linux/ssb/ssb.h 2007-10-14 04:33:25.171714773 +0200 -@@ -255,6 +255,12 @@ +--- linux-2.6.23.16.orig/include/linux/ssb/ssb.h 2008-02-19 01:35:53.000000000 +0100 ++++ linux-2.6.23.16/include/linux/ssb/ssb.h 2008-02-19 01:39:40.000000000 +0100 +@@ -217,6 +217,12 @@ enum ssb_bustype { #define SSB_CHIPPACK_BCM4712M 2 /* Medium 225pin 4712 */ #define SSB_CHIPPACK_BCM4712L 0 /* Large 340pin 4712 */ @@ -139,7 +139,7 @@ Index: linux-2.6.23/include/linux/ssb/ssb.h #include <linux/ssb/ssb_driver_chipcommon.h> #include <linux/ssb/ssb_driver_mips.h> #include <linux/ssb/ssb_driver_extif.h> -@@ -385,6 +391,16 @@ +@@ -349,6 +355,16 @@ static inline void ssb_write32(struct ss dev->ops->write32(dev, offset, value); } @@ -156,11 +156,11 @@ Index: linux-2.6.23/include/linux/ssb/ssb.h /* Translation (routing) bits that need to be ORed to DMA * addresses before they are given to a device. */ -Index: linux-2.6.23/drivers/ssb/driver_chipcommon.c +Index: linux-2.6.23.16/drivers/ssb/driver_chipcommon.c =================================================================== ---- linux-2.6.23.orig/drivers/ssb/driver_chipcommon.c 2007-10-14 04:32:45.797470966 +0200 -+++ linux-2.6.23/drivers/ssb/driver_chipcommon.c 2007-10-14 04:33:25.175715001 +0200 -@@ -351,21 +351,6 @@ +--- linux-2.6.23.16.orig/drivers/ssb/driver_chipcommon.c 2008-02-19 01:35:53.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/driver_chipcommon.c 2008-02-19 02:01:16.000000000 +0100 +@@ -351,21 +351,6 @@ void ssb_chipco_watchdog_timer_set(struc chipco_write32(cc, SSB_CHIPCO_WATCHDOG, ticks); } @@ -182,11 +182,11 @@ Index: linux-2.6.23/drivers/ssb/driver_chipcommon.c #ifdef CONFIG_SSB_SERIAL int ssb_chipco_serial_init(struct ssb_chipcommon *cc, struct ssb_serial_port *ports) -Index: linux-2.6.23/drivers/ssb/driver_extif.c +Index: linux-2.6.23.16/drivers/ssb/driver_extif.c =================================================================== ---- linux-2.6.23.orig/drivers/ssb/driver_extif.c 2007-10-14 04:32:45.809471640 +0200 -+++ linux-2.6.23/drivers/ssb/driver_extif.c 2007-10-14 04:33:25.179715231 +0200 -@@ -110,20 +110,4 @@ +--- linux-2.6.23.16.orig/drivers/ssb/driver_extif.c 2008-02-19 01:35:53.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/driver_extif.c 2008-02-19 01:39:40.000000000 +0100 +@@ -110,20 +110,4 @@ void ssb_extif_get_clockcontrol(struct s *m = extif_read32(extif, SSB_EXTIF_CLOCK_SB); } @@ -207,11 +207,11 @@ Index: linux-2.6.23/drivers/ssb/driver_extif.c - mask, value); -} -Index: linux-2.6.23/include/linux/mod_devicetable.h +Index: linux-2.6.23.16/include/linux/mod_devicetable.h =================================================================== ---- linux-2.6.23.orig/include/linux/mod_devicetable.h 2007-10-14 04:35:22.102378272 +0200 -+++ linux-2.6.23/include/linux/mod_devicetable.h 2007-10-14 04:34:41.172045787 +0200 -@@ -340,4 +340,19 @@ +--- linux-2.6.23.16.orig/include/linux/mod_devicetable.h 2008-02-19 01:35:53.000000000 +0100 ++++ linux-2.6.23.16/include/linux/mod_devicetable.h 2008-02-19 01:39:40.000000000 +0100 +@@ -340,4 +340,19 @@ struct parisc_device_id { #define PA_HVERSION_ANY_ID 0xffff #define PA_SVERSION_ANY_ID 0xffffffff @@ -231,3 +231,62 @@ Index: linux-2.6.23/include/linux/mod_devicetable.h +#define SSB_ANY_REV 0xFF + #endif /* LINUX_MOD_DEVICETABLE_H */ +Index: linux-2.6.23.16/drivers/ssb/main.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/ssb/main.c 2008-02-19 01:45:24.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/main.c 2008-02-19 02:01:16.000000000 +0100 +@@ -321,14 +321,16 @@ static int ssb_bus_match(struct device * + return 0; + } + +-static int ssb_device_uevent(struct device *dev, struct kobj_uevent_env *env) ++static int ssb_device_uevent(struct device *dev, char **envp, ++ int num_envp, char *buffer, int buffer_size) + { + struct ssb_device *ssb_dev = dev_to_ssb_dev(dev); ++ int i = 0, len = 0; + + if (!dev) + return -ENODEV; + +- return add_uevent_var(env, ++ return add_uevent_var(envp, num_envp, &i, buffer, buffer_size, &len, + "MODALIAS=ssb:v%04Xid%04Xrev%02X", + ssb_dev->id.vendor, ssb_dev->id.coreid, + ssb_dev->id.revision); +Index: linux-2.6.23.16/drivers/ssb/scan.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/ssb/scan.c 2008-02-16 19:08:13.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/scan.c 2008-02-19 01:56:02.000000000 +0100 +@@ -391,12 +391,14 @@ int ssb_bus_scan(struct ssb_bus *bus, + if (bus->bustype == SSB_BUSTYPE_PCI) { + /* Ignore PCI cores on PCI-E cards. + * Ignore PCI-E cores on PCI cards. */ ++ //FIXME kernel 2.6.23 doesn't have is_pcie. Add this check back when updating to 2.6.24 or later. + if (dev->id.coreid == SSB_DEV_PCI) { +- if (bus->host_pci->is_pcie) +- continue; ++//FIXME if (bus->host_pci->is_pcie) ++//FIXME continue; + } else { +- if (!bus->host_pci->is_pcie) +- continue; ++ continue; //FIXME ++//FIXME if (!bus->host_pci->is_pcie) ++//FIXME continue; + } + } + if (bus->pcicore.dev) { +Index: linux-2.6.23.16/drivers/ssb/driver_pcicore.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/ssb/driver_pcicore.c 2008-02-19 02:01:11.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/driver_pcicore.c 2008-02-19 02:01:32.000000000 +0100 +@@ -362,7 +362,7 @@ static int pcicore_is_in_hostmode(struct + chipid_top != 0x5300) + return 0; + +- if (bus->sprom.r1.boardflags_lo & SSB_PCICORE_BFL_NOPCI) ++ if (bus->sprom.boardflags_lo & SSB_PCICORE_BFL_NOPCI) + return 0; + + /* The 200-pin BCM4712 package does not bond out PCI. Even when diff --git a/target/linux/brcm47xx/patches-2.6.23/220-bcm5354.patch b/target/linux/brcm47xx/patches-2.6.23/220-bcm5354.patch index c524c8f..e3afcbc 100644 --- a/target/linux/brcm47xx/patches-2.6.23/220-bcm5354.patch +++ b/target/linux/brcm47xx/patches-2.6.23/220-bcm5354.patch @@ -1,6 +1,8 @@ ---- files/drivers/ssb/driver_chipcommon.c 2007-10-24 16:57:38.000000000 -0700 -+++ linux-2.6.23.1/drivers/ssb/driver_chipcommon.c 2007-10-27 13:27:06.000000000 -0700 -@@ -268,6 +268,8 @@ +Index: linux-2.6.23.16/drivers/ssb/driver_chipcommon.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/ssb/driver_chipcommon.c 2008-02-19 00:42:42.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/driver_chipcommon.c 2008-02-19 00:43:34.000000000 +0100 +@@ -268,6 +268,8 @@ void ssb_chipco_resume(struct ssb_chipco void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc, u32 *plltype, u32 *n, u32 *m) { @@ -9,7 +11,7 @@ *n = chipco_read32(cc, SSB_CHIPCO_CLOCK_N); *plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT); switch (*plltype) { -@@ -291,6 +293,8 @@ +@@ -291,6 +293,8 @@ void ssb_chipco_get_clockcpu(struct ssb_ void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc, u32 *plltype, u32 *n, u32 *m) { @@ -18,9 +20,11 @@ *n = chipco_read32(cc, SSB_CHIPCO_CLOCK_N); *plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT); switch (*plltype) { ---- files/drivers/ssb/driver_mipscore.c 2007-10-24 16:57:38.000000000 -0700 -+++ linux-2.6.23.1/drivers/ssb/driver_mipscore.c 2007-10-27 13:29:36.000000000 -0700 -@@ -160,6 +160,8 @@ +Index: linux-2.6.23.16/drivers/ssb/driver_mipscore.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/ssb/driver_mipscore.c 2008-02-19 00:42:42.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/driver_mipscore.c 2008-02-19 00:43:34.000000000 +0100 +@@ -160,6 +160,8 @@ u32 ssb_cpu_clock(struct ssb_mipscore *m if ((pll_type == SSB_PLLTYPE_5) || (bus->chip_id == 0x5365)) { rate = 200000000; @@ -29,9 +33,11 @@ } else { rate = ssb_calc_clock_rate(pll_type, n, m); } ---- files/drivers/ssb/main.c 2007-10-24 16:57:38.000000000 -0700 -+++ linux-2.6.23.1/drivers/ssb/main.c 2007-10-27 13:30:59.000000000 -0700 -@@ -864,6 +864,8 @@ +Index: linux-2.6.23.16/drivers/ssb/main.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/ssb/main.c 2008-02-19 00:42:15.000000000 +0100 ++++ linux-2.6.23.16/drivers/ssb/main.c 2008-02-19 00:43:34.000000000 +0100 +@@ -860,6 +860,8 @@ u32 ssb_clockspeed(struct ssb_bus *bus) if (bus->chip_id == 0x5365) { rate = 100000000; diff --git a/target/linux/brcm47xx/patches-2.6.23/225-bcm5354_ssbrev.patch b/target/linux/brcm47xx/patches-2.6.23/225-bcm5354_ssbrev.patch deleted file mode 100644 index 55209b3..0000000 --- a/target/linux/brcm47xx/patches-2.6.23/225-bcm5354_ssbrev.patch +++ /dev/null @@ -1,20 +0,0 @@ ---- a/drivers/ssb/main.c 2007-11-05 05:59:43.000000000 -0800 -+++ b/drivers/ssb/main.c 2007-11-05 08:59:13.000000000 -0800 -@@ -882,6 +884,7 @@ - case SSB_IDLOW_SSBREV_22: - return SSB_TMSLOW_REJECT_22; - case SSB_IDLOW_SSBREV_23: -+ case SSB_IDLOW_SSBREV_5354: - return SSB_TMSLOW_REJECT_23; - default: - WARN_ON(1); ---- a/include/linux/ssb/ssb_regs.h 2007-11-05 05:59:42.000000000 -0800 -+++ b/include/linux/ssb/ssb_regs.h 2007-11-05 09:00:45.000000000 -0800 -@@ -147,6 +147,7 @@ - #define SSB_IDLOW_SSBREV 0xF0000000 /* Sonics Backplane Revision code */ - #define SSB_IDLOW_SSBREV_22 0x00000000 /* <= 2.2 */ - #define SSB_IDLOW_SSBREV_23 0x10000000 /* 2.3 */ -+#define SSB_IDLOW_SSBREV_5354 0x60000000 /* 5354 */ - #define SSB_IDHIGH 0x0FFC /* SB Identification High */ - #define SSB_IDHIGH_RCLO 0x0000000F /* Revision Code (low part) */ - #define SSB_IDHIGH_CC 0x00008FF0 /* Core Code */ diff --git a/target/linux/brcm47xx/patches-2.6.23/230-ohci-ssb.patch b/target/linux/brcm47xx/patches-2.6.23/230-ohci-ssb.patch index 1db627f..5be1a66 100644 --- a/target/linux/brcm47xx/patches-2.6.23/230-ohci-ssb.patch +++ b/target/linux/brcm47xx/patches-2.6.23/230-ohci-ssb.patch @@ -13,10 +13,10 @@ Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> --- -diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig -index 565d6ef..c978d62 100644 ---- a/drivers/usb/host/Kconfig -+++ b/drivers/usb/host/Kconfig +Index: linux-2.6.23.16/drivers/usb/host/Kconfig +=================================================================== +--- linux-2.6.23.16.orig/drivers/usb/host/Kconfig 2008-02-19 00:47:29.000000000 +0100 ++++ linux-2.6.23.16/drivers/usb/host/Kconfig 2008-02-19 00:47:51.000000000 +0100 @@ -154,6 +154,19 @@ config USB_OHCI_HCD_PCI Enables support for PCI-bus plug-in USB controller cards. If unsure, say Y. @@ -37,11 +37,11 @@ index 565d6ef..c978d62 100644 config USB_OHCI_BIG_ENDIAN_DESC bool depends on USB_OHCI_HCD -diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c -index f7c6ced..240c7f5 100644 ---- a/drivers/usb/host/ohci-hcd.c -+++ b/drivers/usb/host/ohci-hcd.c -@@ -1033,11 +1033,17 @@ MODULE_LICENSE ("GPL"); +Index: linux-2.6.23.16/drivers/usb/host/ohci-hcd.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/usb/host/ohci-hcd.c 2008-02-19 00:47:29.000000000 +0100 ++++ linux-2.6.23.16/drivers/usb/host/ohci-hcd.c 2008-02-19 00:47:51.000000000 +0100 +@@ -926,11 +926,17 @@ MODULE_LICENSE ("GPL"); #define PS3_SYSTEM_BUS_DRIVER ps3_ohci_driver #endif @@ -60,7 +60,7 @@ index f7c6ced..240c7f5 100644 #error "missing bus glue for ohci-hcd" #endif -@@ -1082,10 +1088,20 @@ static int __init ohci_hcd_mod_init(void) +@@ -975,10 +981,20 @@ static int __init ohci_hcd_mod_init(void goto error_pci; #endif @@ -81,7 +81,7 @@ index f7c6ced..240c7f5 100644 error_pci: #endif #ifdef SA1111_DRIVER -@@ -1110,6 +1126,9 @@ module_init(ohci_hcd_mod_init); +@@ -1003,6 +1019,9 @@ module_init(ohci_hcd_mod_init); static void __exit ohci_hcd_mod_exit(void) { @@ -91,11 +91,10 @@ index f7c6ced..240c7f5 100644 #ifdef PCI_DRIVER pci_unregister_driver(&PCI_DRIVER); #endif -diff --git a/drivers/usb/host/ohci-ssb.c b/drivers/usb/host/ohci-ssb.c -new file mode 100644 -index 0000000..bc3e785 ---- /dev/null -+++ b/drivers/usb/host/ohci-ssb.c +Index: linux-2.6.23.16/drivers/usb/host/ohci-ssb.c +=================================================================== +--- /dev/null 1970-01-01 00:00:00.000000000 +0000 ++++ linux-2.6.23.16/drivers/usb/host/ohci-ssb.c 2008-02-19 00:47:51.000000000 +0100 @@ -0,0 +1,247 @@ +/* + * Sonics Silicon Backplane @@ -344,4 +343,3 @@ index 0000000..bc3e785 + .suspend = ssb_ohci_suspend, + .resume = ssb_ohci_resume, +}; - diff --git a/target/linux/generic-2.6/files/drivers/ssb/Kconfig b/target/linux/generic-2.6/files/drivers/ssb/Kconfig index b4a5e5e..d976660 100644 --- a/target/linux/generic-2.6/files/drivers/ssb/Kconfig +++ b/target/linux/generic-2.6/files/drivers/ssb/Kconfig @@ -22,7 +22,7 @@ config SSB config SSB_PCIHOST_POSSIBLE bool - depends on SSB && PCI + depends on SSB && (PCI = y || PCI = SSB) default y config SSB_PCIHOST @@ -37,7 +37,7 @@ config SSB_PCIHOST config SSB_PCMCIAHOST_POSSIBLE bool - depends on SSB && PCMCIA && EXPERIMENTAL + depends on SSB && (PCMCIA = y || PCMCIA = SSB) && EXPERIMENTAL default y config SSB_PCMCIAHOST diff --git a/target/linux/generic-2.6/files/drivers/ssb/b43_pci_bridge.c b/target/linux/generic-2.6/files/drivers/ssb/b43_pci_bridge.c index 1a31f7a..2d27d6d 100644 --- a/target/linux/generic-2.6/files/drivers/ssb/b43_pci_bridge.c +++ b/target/linux/generic-2.6/files/drivers/ssb/b43_pci_bridge.c @@ -1,7 +1,7 @@ /* * Broadcom 43xx PCI-SSB bridge module * - * This technically is a seperate PCI driver module, but + * This technically is a separate PCI driver module, but * because of its small size we include it in the SSB core * instead of creating a standalone module. * diff --git a/target/linux/generic-2.6/files/drivers/ssb/main.c b/target/linux/generic-2.6/files/drivers/ssb/main.c index 74d5182..9028ed5 100644 --- a/target/linux/generic-2.6/files/drivers/ssb/main.c +++ b/target/linux/generic-2.6/files/drivers/ssb/main.c @@ -11,6 +11,7 @@ #include "ssb_private.h" #include <linux/delay.h> +#include <linux/io.h> #include <linux/ssb/ssb.h> #include <linux/ssb/ssb_regs.h> #include <linux/dma-mapping.h> @@ -320,23 +321,17 @@ static int ssb_bus_match(struct device *dev, struct device_driver *drv) return 0; } -static int ssb_device_uevent(struct device *dev, char **envp, int num_envp, - char *buffer, int buffer_size) +static int ssb_device_uevent(struct device *dev, struct kobj_uevent_env *env) { struct ssb_device *ssb_dev = dev_to_ssb_dev(dev); - int ret, i = 0, length = 0; if (!dev) return -ENODEV; - ret = add_uevent_var(envp, num_envp, &i, - buffer, buffer_size, &length, + return add_uevent_var(env, "MODALIAS=ssb:v%04Xid%04Xrev%02X", ssb_dev->id.vendor, ssb_dev->id.coreid, ssb_dev->id.revision); - envp[i] = NULL; - - return ret; } static struct bus_type ssb_bustype = { @@ -445,6 +440,7 @@ static int ssb_devices_register(struct ssb_bus *bus) break; case SSB_BUSTYPE_PCMCIA: #ifdef CONFIG_SSB_PCMCIAHOST + sdev->irq = bus->host_pcmcia->irq.AssignedIRQ; dev->parent = &bus->host_pcmcia->dev; #endif break; @@ -876,14 +872,22 @@ EXPORT_SYMBOL(ssb_clockspeed); static u32 ssb_tmslow_reject_bitmask(struct ssb_device *dev) { + u32 rev = ssb_read32(dev, SSB_IDLOW) & SSB_IDLOW_SSBREV; + /* The REJECT bit changed position in TMSLOW between * Backplane revisions. */ - switch (ssb_read32(dev, SSB_IDLOW) & SSB_IDLOW_SSBREV) { + switch (rev) { case SSB_IDLOW_SSBREV_22: return SSB_TMSLOW_REJECT_22; case SSB_IDLOW_SSBREV_23: return SSB_TMSLOW_REJECT_23; + case SSB_IDLOW_SSBREV_24: /* TODO - find the proper REJECT bits */ + case SSB_IDLOW_SSBREV_25: /* same here */ + case SSB_IDLOW_SSBREV_26: /* same here */ + case SSB_IDLOW_SSBREV_27: /* same here */ + return SSB_TMSLOW_REJECT_23; /* this is a guess */ default: + printk(KERN_INFO "ssb: Backplane Revision 0x%.8X\n", rev); WARN_ON(1); } return (SSB_TMSLOW_REJECT_22 | SSB_TMSLOW_REJECT_23); @@ -1152,7 +1156,10 @@ static int __init ssb_modinit(void) return err; } -subsys_initcall(ssb_modinit); +/* ssb must be initialized after PCI but before the ssb drivers. + * That means we must use some initcall between subsys_initcall + * and device_initcall. */ +fs_initcall(ssb_modinit); static void __exit ssb_modexit(void) { diff --git a/target/linux/generic-2.6/files/drivers/ssb/pci.c b/target/linux/generic-2.6/files/drivers/ssb/pci.c index 0ab095c..b434df7 100644 --- a/target/linux/generic-2.6/files/drivers/ssb/pci.c +++ b/target/linux/generic-2.6/files/drivers/ssb/pci.c @@ -212,29 +212,29 @@ static inline u8 ssb_crc8(u8 crc, u8 data) return t[crc ^ data]; } -static u8 ssb_sprom_crc(const u16 *sprom) +static u8 ssb_sprom_crc(const u16 *sprom, u16 size) { int word; u8 crc = 0xFF; - for (word = 0; word < SSB_SPROMSIZE_WORDS - 1; word++) { + for (word = 0; word < size - 1; word++) { crc = ssb_crc8(crc, sprom[word] & 0x00FF); crc = ssb_crc8(crc, (sprom[word] & 0xFF00) >> 8); } - crc = ssb_crc8(crc, sprom[SPOFF(SSB_SPROM_REVISION)] & 0x00FF); + crc = ssb_crc8(crc, sprom[size - 1] & 0x00FF); crc ^= 0xFF; return crc; } -static int sprom_check_crc(const u16 *sprom) +static int sprom_check_crc(const u16 *sprom, u16 size) { u8 crc; u8 expected_crc; u16 tmp; - crc = ssb_sprom_crc(sprom); - tmp = sprom[SPOFF(SSB_SPROM_REVISION)] & SSB_SPROM_REVISION_CRC; + crc = ssb_sprom_crc(sprom, size); + tmp = sprom[size - 1] & SSB_SPROM_REVISION_CRC; expected_crc = tmp >> SSB_SPROM_REVISION_CRC_SHIFT; if (crc != expected_crc) return -EPROTO; @@ -246,8 +246,8 @@ static void sprom_do_read(struct ssb_bus *bus, u16 *sprom) { int i; - for (i = 0; i < SSB_SPROMSIZE_WORDS; i++) - sprom[i] = readw(bus->mmio + SSB_SPROM_BASE + (i * 2)); + for (i = 0; i < bus->sprom_size; i++) + sprom[i] = ioread16(bus->mmio + SSB_SPROM_BASE + (i * 2)); } static int sprom_do_write(struct ssb_bus *bus, const u16 *sprom) @@ -255,6 +255,7 @@ static int sprom_do_write(struct ssb_bus *bus, const u16 *sprom) struct pci_dev *pdev = bus->host_pci; int i, err; u32 spromctl; + u16 size = bus->sprom_size; ssb_printk(KERN_NOTICE PFX "Writing SPROM. Do NOT turn off the power! Please stand by...\n"); err = pci_read_config_dword(pdev, SSB_SPROMCTL, &spromctl); @@ -266,12 +267,12 @@ static int sprom_do_write(struct ssb_bus *bus, const u16 *sprom) goto err_ctlreg; ssb_printk(KERN_NOTICE PFX "[ 0%%"); msleep(500); - for (i = 0; i < SSB_SPROMSIZE_WORDS; i++) { - if (i == SSB_SPROMSIZE_WORDS / 4) + for (i = 0; i < size; i++) { + if (i == size / 4) ssb_printk("25%%"); - else if (i == SSB_SPROMSIZE_WORDS / 2) + else if (i == size / 2) ssb_printk("50%%"); - else if (i == (SSB_SPROMSIZE_WORDS / 4) * 3) + else if (i == (size * 3) / 4) ssb_printk("75%%"); else if (i % 2) ssb_printk("."); @@ -296,24 +297,53 @@ err_ctlreg: return err; } -static void sprom_extract_r1(struct ssb_sprom_r1 *out, const u16 *in) +static s8 r123_extract_antgain(u8 sprom_revision, const u16 *in, + u16 mask, u16 shift) +{ + u16 v; + u8 gain; + + v = in[SPOFF(SSB_SPROM1_AGAIN)]; + gain = (v & mask) >> shift; + if (gain == 0xFF) + gain = 2; /* If unset use 2dBm */ + if (sprom_revision == 1) { + /* Convert to Q5.2 */ + gain <<= 2; + } else { + /* Q5.2 Fractional part is stored in 0xC0 */ + gain = ((gain & 0xC0) >> 6) | ((gain & 0x3F) << 2); + } + + return (s8)gain; +} + +static void sprom_extract_r123(struct ssb_sprom *out, const u16 *in) { int i; u16 v; + s8 gain; + u16 loc[3]; - SPEX(pci_spid, SSB_SPROM1_SPID, 0xFFFF, 0); - SPEX(pci_svid, SSB_SPROM1_SVID, 0xFFFF, 0); - SPEX(pci_pid, SSB_SPROM1_PID, 0xFFFF, 0); + if (out->revision == 3) { /* rev 3 moved MAC */ + loc[0] = SSB_SPROM3_IL0MAC; + loc[1] = SSB_SPROM3_ET0MAC; + loc[2] = SSB_SPROM3_ET1MAC; + } else { + loc[0] = SSB_SPROM1_IL0MAC; + loc[1] = SSB_SPROM1_ET0MAC; + loc[2] = SSB_SPROM1_ET1MAC; + } for (i = 0; i < 3; i++) { - v = in[SPOFF(SSB_SPROM1_IL0MAC) + i]; + v = in[SPOFF(loc[0]) + i]; *(((__be16 *)out->il0mac) + i) = cpu_to_be16(v); } for (i = 0; i < 3; i++) { - v = in[SPOFF(SSB_SPROM1_ET0MAC) + i]; + v = in[SPOFF(loc[1]) + i]; *(((__be16 *)out->et0mac) + i) = cpu_to_be16(v); } for (i = 0; i < 3; i++) { - v = in[SPOFF(SSB_SPROM1_ET1MAC) + i]; + v = in[SPOFF(loc[2]) + i]; *(((__be16 *)out->et1mac) + i) = cpu_to_be16(v); } SPEX(et0phyaddr, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET0A, 0); @@ -324,9 +354,9 @@ static void sprom_extract_r1(struct ssb_sprom_r1 *out, const u16 *in) SPEX(board_rev, SSB_SPROM1_BINF, SSB_SPROM1_BINF_BREV, 0); SPEX(country_code, SSB_SPROM1_BINF, SSB_SPROM1_BINF_CCODE, SSB_SPROM1_BINF_CCODE_SHIFT); - SPEX(antenna_a, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTA, + SPEX(ant_available_a, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTA, SSB_SPROM1_BINF_ANTA_SHIFT); - SPEX(antenna_bg, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTBG, + SPEX(ant_available_bg, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTBG, SSB_SPROM1_BINF_ANTBG_SHIFT); SPEX(pa0b0, SSB_SPROM1_PA0B0, 0xFFFF, 0); SPEX(pa0b1, SSB_SPROM1_PA0B1, 0xFFFF, 0); @@ -347,100 +377,108 @@ static void sprom_extract_r1(struct ssb_sprom_r1 *out, const u16 *in) SSB_SPROM1_ITSSI_A_SHIFT); SPEX(itssi_bg, SSB_SPROM1_ITSSI, SSB_SPROM1_ITSSI_BG, 0); SPEX(boardflags_lo, SSB_SPROM1_BFLLO, 0xFFFF, 0); - SPEX(antenna_gain_a, SSB_SPROM1_AGAIN, SSB_SPROM1_AGAIN_A, 0); - SPEX(antenna_gain_bg, SSB_SPROM1_AGAIN, SSB_SPROM1_AGAIN_BG, - SSB_SPROM1_AGAIN_BG_SHIFT); - for (i = 0; i < 4; i++) { - v = in[SPOFF(SSB_SPROM1_OEM) + i]; - *(((__le16 *)out->oem) + i) = cpu_to_le16(v); - } + if (out->revision >= 2) + SPEX(boardflags_hi, SSB_SPROM2_BFLHI, 0xFFFF, 0); + + /* Extract the antenna gain values. */ + gain = r123_extract_antgain(out->revision, in, + SSB_SPROM1_AGAIN_BG, + SSB_SPROM1_AGAIN_BG_SHIFT); + out->antenna_gain.ghz24.a0 = gain; + out->antenna_gain.ghz24.a1 = gain; + out->antenna_gain.ghz24.a2 = gain; + out->antenna_gain.ghz24.a3 = gain; + gain = r123_extract_antgain(out->revision, in, + SSB_SPROM1_AGAIN_A, + SSB_SPROM1_AGAIN_A_SHIFT); + out->antenna_gain.ghz5.a0 = gain; + out->antenna_gain.ghz5.a1 = gain; + out->antenna_gain.ghz5.a2 = gain; + out->antenna_gain.ghz5.a3 = gain; } -static void sprom_extract_r2(struct ssb_sprom_r2 *out, const u16 *in) +static void sprom_extract_r4(struct ssb_sprom *out, const u16 *in) { int i; u16 v; - SPEX(boardflags_hi, SSB_SPROM2_BFLHI, 0xFFFF, 0); - SPEX(maxpwr_a_hi, SSB_SPROM2_MAXP_A, SSB_SPROM2_MAXP_A_HI, 0); - SPEX(maxpwr_a_lo, SSB_SPROM2_MAXP_A, SSB_SPROM2_MAXP_A_LO, - SSB_SPROM2_MAXP_A_LO_SHIFT); - SPEX(pa1lob0, SSB_SPROM2_PA1LOB0, 0xFFFF, 0); - SPEX(pa1lob1, SSB_SPROM2_PA1LOB1, 0xFFFF, 0); - SPEX(pa1lob2, SSB_SPROM2_PA1LOB2, 0xFFFF, 0); - SPEX(pa1hib0, SSB_SPROM2_PA1HIB0, 0xFFFF, 0); - SPEX(pa1hib1, SSB_SPROM2_PA1HIB1, 0xFFFF, 0); - SPEX(pa1hib2, SSB_SPROM2_PA1HIB2, 0xFFFF, 0); - SPEX(ofdm_pwr_off, SSB_SPROM2_OPO, SSB_SPROM2_OPO_VALUE, 0); - for (i = 0; i < 4; i++) { - v = in[SPOFF(SSB_SPROM2_CCODE) + i]; - *(((__le16 *)out->country_str) + i) = cpu_to_le16(v); + /* extract the equivalent of the r1 variables */ + for (i = 0; i < 3; i++) { + v = in[SPOFF(SSB_SPROM4_IL0MAC) + i]; + *(((__be16 *)out->il0mac) + i) = cpu_to_be16(v); } + for (i = 0; i < 3; i++) { + v = in[SPOFF(SSB_SPROM4_ET0MAC) + i]; + *(((__be16 *)out->et0mac) + i) = cpu_to_be16(v); + } + for (i = 0; i < 3; i++) { + v = in[SPOFF(SSB_SPROM4_ET1MAC) + i]; + *(((__be16 *)out->et1mac) + i) = cpu_to_be16(v); + } + SPEX(et0phyaddr, SSB_SPROM4_ETHPHY, SSB_SPROM4_ETHPHY_ET0A, 0); + SPEX(et1phyaddr, SSB_SPROM4_ETHPHY, SSB_SPROM4_ETHPHY_ET1A, + SSB_SPROM4_ETHPHY_ET1A_SHIFT); + SPEX(country_code, SSB_SPROM4_CCODE, 0xFFFF, 0); + SPEX(boardflags_lo, SSB_SPROM4_BFLLO, 0xFFFF, 0); + SPEX(boardflags_hi, SSB_SPROM4_BFLHI, 0xFFFF, 0); + SPEX(ant_available_a, SSB_SPROM4_ANTAVAIL, SSB_SPROM4_ANTAVAIL_A, + SSB_SPROM4_ANTAVAIL_A_SHIFT); + SPEX(ant_available_bg, SSB_SPROM4_ANTAVAIL, SSB_SPROM4_ANTAVAIL_BG, + SSB_SPROM4_ANTAVAIL_BG_SHIFT); + SPEX(maxpwr_bg, SSB_SPROM4_MAXP_BG, SSB_SPROM4_MAXP_BG_MASK, 0); + SPEX(itssi_bg, SSB_SPROM4_MAXP_BG, SSB_SPROM4_ITSSI_BG, + SSB_SPROM4_ITSSI_BG_SHIFT); + SPEX(maxpwr_a, SSB_SPROM4_MAXP_A, SSB_SPROM4_MAXP_A_MASK, 0); + SPEX(itssi_a, SSB_SPROM4_MAXP_A, SSB_SPROM4_ITSSI_A, + SSB_SPROM4_ITSSI_A_SHIFT); + SPEX(gpio0, SSB_SPROM4_GPIOA, SSB_SPROM4_GPIOA_P0, 0); + SPEX(gpio1, SSB_SPROM4_GPIOA, SSB_SPROM4_GPIOA_P1, + SSB_SPROM4_GPIOA_P1_SHIFT); + SPEX(gpio2, SSB_SPROM4_GPIOB, SSB_SPROM4_GPIOB_P2, 0); + SPEX(gpio3, SSB_SPROM4_GPIOB, SSB_SPROM4_GPIOB_P3, + SSB_SPROM4_GPIOB_P3_SHIFT); + + /* Extract the antenna gain values. */ + SPEX(antenna_gain.ghz24.a0, SSB_SPROM4_AGAIN01, + SSB_SPROM4_AGAIN0, SSB_SPROM4_AGAIN0_SHIFT); + SPEX(antenna_gain.ghz24.a1, SSB_SPROM4_AGAIN01, + SSB_SPROM4_AGAIN1, SSB_SPROM4_AGAIN1_SHIFT); + SPEX(antenna_gain.ghz24.a2, SSB_SPROM4_AGAIN23, + SSB_SPROM4_AGAIN2, SSB_SPROM4_AGAIN2_SHIFT); + SPEX(antenna_gain.ghz24.a3, SSB_SPROM4_AGAIN23, + SSB_SPROM4_AGAIN3, SSB_SPROM4_AGAIN3_SHIFT); + memcpy(&out->antenna_gain.ghz5, &out->antenna_gain.ghz24, + sizeof(out->antenna_gain.ghz5)); + + /* TODO - get remaining rev 4 stuff needed */ } -static void sprom_extract_r3(struct ssb_sprom_r3 *out, const u16 *in) -{ - out->ofdmapo = (in[SPOFF(SSB_SPROM3_OFDMAPO) + 0] & 0xFF00) >> 8; - out->ofdmapo |= (in[SPOFF(SSB_SPROM3_OFDMAPO) + 0] & 0x00FF) << 8; - out->ofdmapo <<= 16; - out->ofdmapo |= (in[SPOFF(SSB_SPROM3_OFDMAPO) + 1] & 0xFF00) >> 8; - out->ofdmapo |= (in[SPOFF(SSB_SPROM3_OFDMAPO) + 1] & 0x00FF) << 8; - - out->ofdmalpo = (in[SPOFF(SSB_SPROM3_OFDMALPO) + 0] & 0xFF00) >> 8; - out->ofdmalpo |= (in[SPOFF(SSB_SPROM3_OFDMALPO) + 0] & 0x00FF) << 8; - out->ofdmalpo <<= 16; - out->ofdmalpo |= (in[SPOFF(SSB_SPROM3_OFDMALPO) + 1] & 0xFF00) >> 8; - out->ofdmalpo |= (in[SPOFF(SSB_SPROM3_OFDMALPO) + 1] & 0x00FF) << 8; - - out->ofdmahpo = (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 0] & 0xFF00) >> 8; - out->ofdmahpo |= (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 0] & 0x00FF) << 8; - out->ofdmahpo <<= 16; - out->ofdmahpo |= (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 1] & 0xFF00) >> 8; - out->ofdmahpo |= (in[SPOFF(SSB_SPROM3_OFDMAHPO) + 1] & 0x00FF) << 8; - - SPEX(gpioldc_on_cnt, SSB_SPROM3_GPIOLDC, SSB_SPROM3_GPIOLDC_ON, - SSB_SPROM3_GPIOLDC_ON_SHIFT); - SPEX(gpioldc_off_cnt, SSB_SPROM3_GPIOLDC, SSB_SPROM3_GPIOLDC_OFF, - SSB_SPROM3_GPIOLDC_OFF_SHIFT); - SPEX(cckpo_1M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_1M, 0); - SPEX(cckpo_2M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_2M, - SSB_SPROM3_CCKPO_2M_SHIFT); - SPEX(cckpo_55M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_55M, - SSB_SPROM3_CCKPO_55M_SHIFT); - SPEX(cckpo_11M, SSB_SPROM3_CCKPO, SSB_SPROM3_CCKPO_11M, - SSB_SPROM3_CCKPO_11M_SHIFT); - - out->ofdmgpo = (in[SPOFF(SSB_SPROM3_OFDMGPO) + 0] & 0xFF00) >> 8; - out->ofdmgpo |= (in[SPOFF(SSB_SPROM3_OFDMGPO) + 0] & 0x00FF) << 8; - out->ofdmgpo <<= 16; - out->ofdmgpo |= (in[SPOFF(SSB_SPROM3_OFDMGPO) + 1] & 0xFF00) >> 8; - out->ofdmgpo |= (in[SPOFF(SSB_SPROM3_OFDMGPO) + 1] & 0x00FF) << 8; -} - -static int sprom_extract(struct ssb_bus *bus, - struct ssb_sprom *out, const u16 *in) +static int sprom_extract(struct ssb_bus *bus, struct ssb_sprom *out, + const u16 *in, u16 size) { memset(out, 0, sizeof(*out)); - SPEX(revision, SSB_SPROM_REVISION, SSB_SPROM_REVISION_REV, 0); - SPEX(crc, SSB_SPROM_REVISION, SSB_SPROM_REVISION_CRC, - SSB_SPROM_REVISION_CRC_SHIFT); - + out->revision = in[size - 1] & 0x00FF; + ssb_dprintk(KERN_DEBUG PFX "SPROM revision %d detected.\n", out->revision); if ((bus->chip_id & 0xFF00) == 0x4400) { /* Workaround: The BCM44XX chip has a stupid revision * number stored in the SPROM. * Always extract r1. */ - sprom_extract_r1(&out->r1, in); + out->revision = 1; + sprom_extract_r123(out, in); + } else if (bus->chip_id == 0x4321) { + /* the BCM4328 has a chipid == 0x4321 and a rev 4 SPROM */ + out->revision = 4; + sprom_extract_r4(out, in); } else { if (out->revision == 0) goto unsupported; - if (out->revision >= 1 && out->revision <= 3) - sprom_extract_r1(&out->r1, in); - if (out->revision >= 2 && out->revision <= 3) - sprom_extract_r2(&out->r2, in); - if (out->revision == 3) - sprom_extract_r3(&out->r3, in); - if (out->revision >= 4) + if (out->revision >= 1 && out->revision <= 3) { + sprom_extract_r123(out, in); + } + if (out->revision == 4) + sprom_extract_r4(out, in); + if (out->revision >= 5) goto unsupported; } @@ -448,7 +486,7 @@ static int sprom_extract(struct ssb_bus *bus, unsupported: ssb_printk(KERN_WARNING PFX "Unsupported SPROM revision %d " "detected. Will extract v1\n", out->revision); - sprom_extract_r1(&out->r1, in); + sprom_extract_r123(out, in); return 0; } @@ -458,16 +496,29 @@ static int ssb_pci_sprom_get(struct ssb_bus *bus, int err = -ENOMEM; u16 *buf; - buf = kcalloc(SSB_SPROMSIZE_WORDS, sizeof(u16), GFP_KERNEL); + buf = kcalloc(SSB_SPROMSIZE_WORDS_R123, sizeof(u16), GFP_KERNEL); if (!buf) goto out; + bus->sprom_size = SSB_SPROMSIZE_WORDS_R123; sprom_do_read(bus, buf); - err = sprom_check_crc(buf); + err = sprom_check_crc(buf, bus->sprom_size); if (err) { - ssb_printk(KERN_WARNING PFX - "WARNING: Invalid SPROM CRC (corrupt SPROM)\n"); + /* check for rev 4 sprom - has special signature */ + if (buf[32] == 0x5372) { + kfree(buf); + buf = kcalloc(SSB_SPROMSIZE_WORDS_R4, sizeof(u16), + GFP_KERNEL); + if (!buf) + goto out; + bus->sprom_size = SSB_SPROMSIZE_WORDS_R4; + sprom_do_read(bus, buf); + err = sprom_check_crc(buf, bus->sprom_size); + } + if (err) + ssb_printk(KERN_WARNING PFX "WARNING: Invalid" + " SPROM CRC (corrupt SPROM)\n"); } - err = sprom_extract(bus, sprom, buf); + err = sprom_extract(bus, sprom, buf, bus->sprom_size); kfree(buf); out: @@ -581,29 +632,28 @@ const struct ssb_bus_ops ssb_pci_ops = { .write32 = ssb_pci_write32, }; -static int sprom2hex(const u16 *sprom, char *buf, size_t buf_len) +static int sprom2hex(const u16 *sprom, char *buf, size_t buf_len, u16 size) { int i, pos = 0; - for (i = 0; i < SSB_SPROMSIZE_WORDS; i++) { + for (i = 0; i < size; i++) pos += snprintf(buf + pos, buf_len - pos - 1, "%04X", swab16(sprom[i]) & 0xFFFF); - } pos += snprintf(buf + pos, buf_len - pos - 1, "\n"); return pos + 1; } -static int hex2sprom(u16 *sprom, const char *dump, size_t len) +static int hex2sprom(u16 *sprom, const char *dump, size_t len, u16 size) { char tmp[5] = { 0 }; int cnt = 0; unsigned long parsed; - if (len < SSB_SPROMSIZE_BYTES * 2) + if (len < size * 2) return -EINVAL; - while (cnt < SSB_SPROMSIZE_WORDS) { + while (cnt < size) { memcpy(tmp, dump, 4); dump += 4; parsed = simple_strtoul(tmp, NULL, 16); @@ -627,7 +677,7 @@ static ssize_t ssb_pci_attr_sprom_show(struct device *pcidev, if (!bus) goto out; err = -ENOMEM; - sprom = kcalloc(SSB_SPROMSIZE_WORDS, sizeof(u16), GFP_KERNEL); + sprom = kcalloc(bus->sprom_size, sizeof(u16), GFP_KERNEL); if (!sprom) goto out; @@ -640,7 +690,7 @@ static ssize_t ssb_pci_attr_sprom_show(struct device *pcidev, sprom_do_read(bus, sprom); mutex_unlock(&bus->pci_sprom_mutex); - count = sprom2hex(sprom, buf, PAGE_SIZE); + count = sprom2hex(sprom, buf, PAGE_SIZE, bus->sprom_size); err = 0; out_kfree: @@ -662,15 +712,15 @@ static ssize_t ssb_pci_attr_sprom_store(struct device *pcidev, if (!bus) goto out; err = -ENOMEM; - sprom = kcalloc(SSB_SPROMSIZE_WORDS, sizeof(u16), GFP_KERNEL); + sprom = kcalloc(bus->sprom_size, sizeof(u16), GFP_KERNEL); if (!sprom) goto out; - err = hex2sprom(sprom, buf, count); + err = hex2sprom(sprom, buf, count, bus->sprom_size); if (err) { err = -EINVAL; goto out_kfree; } - err = sprom_check_crc(sprom); + err = sprom_check_crc(sprom, bus->sprom_size); if (err) { err = -EINVAL; goto out_kfree; diff --git a/target/linux/generic-2.6/files/drivers/ssb/pcmcia.c b/target/linux/generic-2.6/files/drivers/ssb/pcmcia.c index 7c77360..46816cd 100644 --- a/target/linux/generic-2.6/files/drivers/ssb/pcmcia.c +++ b/target/linux/generic-2.6/files/drivers/ssb/pcmcia.c @@ -10,6 +10,7 @@ #include <linux/ssb/ssb.h> #include <linux/delay.h> +#include <linux/io.h> #include <pcmcia/cs_types.h> #include <pcmcia/cs.h> @@ -62,17 +63,17 @@ int ssb_pcmcia_switch_coreidx(struct ssb_bus *bus, err = pcmcia_access_configuration_register(pdev, ®); if (err != CS_SUCCESS) goto error; - read_addr |= (reg.Value & 0xF) << 12; + read_addr |= ((u32)(reg.Value & 0x0F)) << 12; reg.Offset = 0x30; err = pcmcia_access_configuration_register(pdev, ®); if (err != CS_SUCCESS) goto error; - read_addr |= reg.Value << 16; + read_addr |= ((u32)reg.Value) << 16; reg.Offset = 0x32; err = pcmcia_access_configuration_register(pdev, ®); if (err != CS_SUCCESS) goto error; - read_addr |= reg.Value << 24; + read_addr |= ((u32)reg.Value) << 24; cur_core = (read_addr - SSB_ENUM_BASE) / SSB_CORE_SIZE; if (cur_core == coreidx) @@ -93,7 +94,6 @@ int ssb_pcmcia_switch_core(struct ssb_bus *bus, struct ssb_device *dev) { int err; - unsigned long flags; #if SSB_VERBOSE_PCMCIACORESWITCH_DEBUG ssb_printk(KERN_INFO PFX @@ -102,11 +102,9 @@ int ssb_pcmcia_switch_core(struct ssb_bus *bus, dev->core_index); #endif - spin_lock_irqsave(&bus->bar_lock, flags); err = ssb_pcmcia_switch_coreidx(bus, dev->core_index); if (!err) bus->mapped_device = dev; - spin_unlock_irqrestore(&bus->bar_lock, flags); return err; } @@ -114,14 +112,12 @@ int ssb_pcmcia_switch_core(struct ssb_bus *bus, int ssb_pcmcia_switch_segment(struct ssb_bus *bus, u8 seg) { int attempts = 0; - unsigned long flags; conf_reg_t reg; - int res, err = 0; + int res; SSB_WARN_ON((seg != 0) && (seg != 1)); reg.Offset = 0x34; reg.Function = 0; - spin_lock_irqsave(&bus->bar_lock, flags); while (1) { reg.Action = CS_WRITE; reg.Value = seg; @@ -142,37 +138,36 @@ int ssb_pcmcia_switch_segment(struct ssb_bus *bus, u8 seg) udelay(10); } bus->mapped_pcmcia_seg = seg; -out_unlock: - spin_unlock_irqrestore(&bus->bar_lock, flags); - return err; + + return 0; error: ssb_printk(KERN_ERR PFX "Failed to switch pcmcia segment\n"); - err = -ENODEV; - goto out_unlock; + return -ENODEV; } -/* These are the main device register access functions. - * do_select_core is inline to have the likely hotpath inline. - * All unlikely codepaths are out-of-line. */ -static inline int do_select_core(struct ssb_bus *bus, - struct ssb_device *dev, - u16 *offset) +static int select_core_and_segment(struct ssb_device *dev, + u16 *offset) { + struct ssb_bus *bus = dev->bus; int err; - u8 need_seg = (*offset >= 0x800) ? 1 : 0; + u8 need_segment; + + if (*offset >= 0x800) { + *offset -= 0x800; + need_segment = 1; + } else + need_segment = 0; if (unlikely(dev != bus->mapped_device)) { err = ssb_pcmcia_switch_core(bus, dev); if (unlikely(err)) return err; } - if (unlikely(need_seg != bus->mapped_pcmcia_seg)) { - err = ssb_pcmcia_switch_segment(bus, need_seg); + if (unlikely(need_segment != bus->mapped_pcmcia_seg)) { + err = ssb_pcmcia_switch_segment(bus, need_segment); if (unlikely(err)) return err; } - if (need_seg == 1) - *offset -= 0x800; return 0; } @@ -180,46 +175,65 @@ static inline int do_select_core(struct ssb_bus *bus, static u16 ssb_pcmcia_read16(struct ssb_device *dev, u16 offset) { struct ssb_bus *bus = dev->bus; - u16 x; + unsigned long flags; + int err; + u16 value = 0xFFFF; - if (unlikely(do_select_core(bus, dev, &offset))) - return 0xFFFF; - x = readw(bus->mmio + offset); + spin_lock_irqsave(&bus->bar_lock, flags); + err = select_core_and_segment(dev, &offset); + if (likely(!err)) + value = readw(bus->mmio + offset); + spin_unlock_irqrestore(&bus->bar_lock, flags); - return x; + return value; } static u32 ssb_pcmcia_read32(struct ssb_device *dev, u16 offset) { struct ssb_bus *bus = dev->bus; - u32 x; + unsigned long flags; + int err; + u32 lo = 0xFFFFFFFF, hi = 0xFFFFFFFF; - if (unlikely(do_select_core(bus, dev, &offset))) - return 0xFFFFFFFF; - x = readl(bus->mmio + offset); + spin_lock_irqsave(&bus->bar_lock, flags); + err = select_core_and_segment(dev, &offset); + if (likely(!err)) { + lo = readw(bus->mmio + offset); + hi = readw(bus->mmio + offset + 2); + } + spin_unlock_irqrestore(&bus->bar_lock, flags); - return x; + return (lo | (hi << 16)); } static void ssb_pcmcia_write16(struct ssb_device *dev, u16 offset, u16 value) { struct ssb_bus *bus = dev->bus; + unsigned long flags; + int err; - if (unlikely(do_select_core(bus, dev, &offset))) - return; - writew(value, bus->mmio + offset); + spin_lock_irqsave(&bus->bar_lock, flags); + err = select_core_and_segment(dev, &offset); + if (likely(!err)) + writew(value, bus->mmio + offset); + mmiowb(); + spin_unlock_irqrestore(&bus->bar_lock, flags); } static void ssb_pcmcia_write32(struct ssb_device *dev, u16 offset, u32 value) { struct ssb_bus *bus = dev->bus; + unsigned long flags; + int err; - if (unlikely(do_select_core(bus, dev, &offset))) - return; - readw(bus->mmio + offset); - writew(value >> 16, bus->mmio + offset + 2); - readw(bus->mmio + offset); - writew(value, bus->mmio + offset); + spin_lock_irqsave(&bus->bar_lock, flags); + err = select_core_and_segment(dev, &offset); + if (likely(!err)) { + writew((value & 0x0000FFFF), bus->mmio + offset); + writew(((value & 0xFFFF0000) >> 16), bus->mmio + offset + 2); + } + mmiowb(); + spin_unlock_irqrestore(&bus->bar_lock, flags); } /* Not "static", as it's used in main.c */ @@ -230,10 +244,12 @@ const struct ssb_bus_ops ssb_pcmcia_ops = { .write32 = ssb_pcmcia_write32, }; +#include <linux/etherdevice.h> int ssb_pcmcia_get_invariants(struct ssb_bus *bus, struct ssb_init_invariants *iv) { //TODO + random_ether_addr(iv->sprom.il0mac); return 0; } diff --git a/target/linux/generic-2.6/files/drivers/ssb/scan.c b/target/linux/generic-2.6/files/drivers/ssb/scan.c index 96258c6..63ee5cf 100644 --- a/target/linux/generic-2.6/files/drivers/ssb/scan.c +++ b/target/linux/generic-2.6/files/drivers/ssb/scan.c @@ -388,6 +388,17 @@ int ssb_bus_scan(struct ssb_bus *bus, case SSB_DEV_PCI: case SSB_DEV_PCIE: #ifdef CONFIG_SSB_DRIVER_PCICORE + if (bus->bustype == SSB_BUSTYPE_PCI) { + /* Ignore PCI cores on PCI-E cards. + * Ignore PCI-E cores on PCI cards. */ + if (dev->id.coreid == SSB_DEV_PCI) { + if (bus->host_pci->is_pcie) + continue; + } else { + if (!bus->host_pci->is_pcie) + continue; + } + } if (bus->pcicore.dev) { ssb_printk(KERN_WARNING PFX "WARNING: Multiple PCI(E) cores found\n"); diff --git a/target/linux/generic-2.6/files/include/linux/ssb/ssb.h b/target/linux/generic-2.6/files/include/linux/ssb/ssb.h index 2b5c312..9d5da8b 100644 --- a/target/linux/generic-2.6/files/include/linux/ssb/ssb.h +++ b/target/linux/generic-2.6/files/include/linux/ssb/ssb.h @@ -15,22 +15,19 @@ struct pcmcia_device; struct ssb_bus; struct ssb_driver; - -struct ssb_sprom_r1 { - u16 pci_spid; /* Subsystem Product ID for PCI */ - u16 pci_svid; /* Subsystem Vendor ID for PCI */ - u16 pci_pid; /* Product ID for PCI */ +struct ssb_sprom { + u8 revision; u8 il0mac[6]; /* MAC address for 802.11b/g */ u8 et0mac[6]; /* MAC address for Ethernet */ u8 et1mac[6]; /* MAC address for 802.11a */ - u8 et0phyaddr:5; /* MII address for enet0 */ - u8 et1phyaddr:5; /* MII address for enet1 */ - u8 et0mdcport:1; /* MDIO for enet0 */ - u8 et1mdcport:1; /* MDIO for enet1 */ - u8 board_rev; /* Board revision */ - u8 country_code:4; /* Country Code */ - u8 antenna_a:2; /* Antenna 0/1 available for A-PHY */ - u8 antenna_bg:2; /* Antenna 0/1 available for B-PHY and G-PHY */ + u8 et0phyaddr; /* MII address for enet0 */ + u8 et1phyaddr; /* MII address for enet1 */ + u8 et0mdcport; /* MDIO for enet0 */ + u8 et1mdcport; /* MDIO for enet1 */ + u8 board_rev; /* Board revision number from SPROM. */ + u8 country_code; /* Country Code */ + u8 ant_available_a; /* A-PHY antenna available bits (up to 4) */ + u8 ant_available_bg; /* B/G-PHY antenna available bits (up to 4) */ u16 pa0b0; u16 pa0b1; u16 pa0b2; @@ -41,61 +38,26 @@ struct ssb_sprom_r1 { u8 gpio1; /* GPIO pin 1 */ u8 gpio2; /* GPIO pin 2 */ u8 gpio3; /* GPIO pin 3 */ - u16 maxpwr_a; /* A-PHY Power Amplifier Max Power (in dBm Q5.2) */ - u16 maxpwr_bg; /* B/G-PHY Power Amplifier Max Power (in dBm Q5.2) */ + u16 maxpwr_a; /* A-PHY Amplifier Max Power (in dBm Q5.2) */ + u16 maxpwr_bg; /* B/G-PHY Amplifier Max Power (in dBm Q5.2) */ u8 itssi_a; /* Idle TSSI Target for A-PHY */ u8 itssi_bg; /* Idle TSSI Target for B/G-PHY */ u16 boardflags_lo; /* Boardflags (low 16 bits) */ - u8 antenna_gain_a; /* A-PHY Antenna gain (in dBm Q5.2) */ - u8 antenna_gain_bg; /* B/G-PHY Antenna gain (in dBm Q5.2) */ - u8 oem[8]; /* OEM string (rev 1 only) */ -}; - -struct ssb_sprom_r2 { u16 boardflags_hi; /* Boardflags (high 16 bits) */ - u8 maxpwr_a_lo; /* A-PHY Max Power Low */ - u8 maxpwr_a_hi; /* A-PHY Max Power High */ - u16 pa1lob0; /* A-PHY PA Low Settings */ - u16 pa1lob1; /* A-PHY PA Low Settings */ - u16 pa1lob2; /* A-PHY PA Low Settings */ - u16 pa1hib0; /* A-PHY PA High Settings */ - u16 pa1hib1; /* A-PHY PA High Settings */ - u16 pa1hib2; /* A-PHY PA High Settings */ - u8 ofdm_pwr_off; /* OFDM Power Offset from CCK Level */ - u8 country_str[2]; /* Two char Country Code */ -}; -struct ssb_sprom_r3 { - u32 ofdmapo; /* A-PHY OFDM Mid Power Offset */ - u32 ofdmalpo; /* A-PHY OFDM Low Power Offset */ - u32 ofdmahpo; /* A-PHY OFDM High Power Offset */ - u8 gpioldc_on_cnt; /* GPIO LED Powersave Duty Cycle ON count */ - u8 gpioldc_off_cnt; /* GPIO LED Powersave Duty Cycle OFF count */ - u8 cckpo_1M:4; /* CCK Power Offset for Rate 1M */ - u8 cckpo_2M:4; /* CCK Power Offset for Rate 2M */ - u8 cckpo_55M:4; /* CCK Power Offset for Rate 5.5M */ - u8 cckpo_11M:4; /* CCK Power Offset for Rate 11M */ - u32 ofdmgpo; /* G-PHY OFDM Power Offset */ -}; - -struct ssb_sprom_r4 { - /* TODO */ -}; - -struct ssb_sprom { - u8 revision; - u8 crc; - /* The valid r# fields are selected by the "revision". - * Revision 3 and lower inherit from lower revisions. - */ - union { + /* Antenna gain values for up to 4 antennas + * on each band. Values in dBm/4 (Q5.2). Negative gain means the + * loss in the connectors is bigger than the gain. */ + struct { + struct { + s8 a0, a1, a2, a3; + } ghz24; /* 2.4GHz band */ struct { - struct ssb_sprom_r1 r1; - struct ssb_sprom_r2 r2; - struct ssb_sprom_r3 r3; - }; - struct ssb_sprom_r4 r4; - }; + s8 a0, a1, a2, a3; + } ghz5; /* 5GHz band */ + } antenna_gain; + + /* TODO - add any parameters needed from rev 2, 3, or 4 SPROMs */ }; /* Information about the PCB the circuitry is soldered on. */ @@ -270,7 +232,8 @@ struct ssb_bus { struct ssb_device *mapped_device; /* Currently mapped PCMCIA segment. (bustype == SSB_BUSTYPE_PCMCIA only) */ u8 mapped_pcmcia_seg; - /* Lock for core and segment switching. */ + /* Lock for core and segment switching. + * On PCMCIA-host busses this is used to protect the whole MMIO access. */ spinlock_t bar_lock; /* The bus this backplane is running on. */ @@ -288,6 +251,7 @@ struct ssb_bus { /* ID information about the Chip. */ u16 chip_id; u16 chip_rev; + u16 sprom_size; /* number of words in sprom */ u8 chip_package; /* List of devices (cores) on the backplane. */ @@ -402,6 +366,22 @@ static inline void ssb_pcihost_unregister(struct pci_driver *driver) { pci_unregister_driver(driver); } + +static inline +void ssb_pcihost_set_power_state(struct ssb_device *sdev, pci_power_t state) +{ + if (sdev->bus->bustype == SSB_BUSTYPE_PCI) + pci_set_power_state(sdev->bus->host_pci, state); +} +#else +static inline void ssb_pcihost_unregister(struct pci_driver *driver) +{ +} + +static inline +void ssb_pcihost_set_power_state(struct ssb_device *sdev, pci_power_t state) +{ +} #endif /* CONFIG_SSB_PCIHOST */ diff --git a/target/linux/generic-2.6/files/include/linux/ssb/ssb_regs.h b/target/linux/generic-2.6/files/include/linux/ssb/ssb_regs.h index 47c7c71..ebad0ba 100644 --- a/target/linux/generic-2.6/files/include/linux/ssb/ssb_regs.h +++ b/target/linux/generic-2.6/files/include/linux/ssb/ssb_regs.h @@ -147,6 +147,10 @@ #define SSB_IDLOW_SSBREV 0xF0000000 /* Sonics Backplane Revision code */ #define SSB_IDLOW_SSBREV_22 0x00000000 /* <= 2.2 */ #define SSB_IDLOW_SSBREV_23 0x10000000 /* 2.3 */ +#define SSB_IDLOW_SSBREV_24 0x40000000 /* ?? Found in BCM4328 */ +#define SSB_IDLOW_SSBREV_25 0x50000000 /* ?? Not Found yet */ +#define SSB_IDLOW_SSBREV_26 0x60000000 /* ?? Found in some BCM4311/2 */ +#define SSB_IDLOW_SSBREV_27 0x70000000 /* ?? Found in some BCM4311/2 */ #define SSB_IDHIGH 0x0FFC /* SB Identification High */ #define SSB_IDHIGH_RCLO 0x0000000F /* Revision Code (low part) */ #define SSB_IDHIGH_CC 0x00008FF0 /* Core Code */ @@ -162,11 +166,16 @@ */ #define SSB_SPROMSIZE_WORDS 64 #define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16)) +#define SSB_SPROMSIZE_WORDS_R123 64 +#define SSB_SPROMSIZE_WORDS_R4 220 +#define SSB_SPROMSIZE_BYTES_R123 (SSB_SPROMSIZE_WORDS_R123 * sizeof(u16)) +#define SSB_SPROMSIZE_BYTES_R4 (SSB_SPROMSIZE_WORDS_R4 * sizeof(u16)) #define SSB_SPROM_BASE 0x1000 #define SSB_SPROM_REVISION 0x107E #define SSB_SPROM_REVISION_REV 0x00FF /* SPROM Revision number */ #define SSB_SPROM_REVISION_CRC 0xFF00 /* SPROM CRC8 value */ #define SSB_SPROM_REVISION_CRC_SHIFT 8 + /* SPROM Revision 1 */ #define SSB_SPROM1_SPID 0x1004 /* Subsystem Product ID for PCI */ #define SSB_SPROM1_SVID 0x1006 /* Subsystem Vendor ID for PCI */ @@ -184,10 +193,10 @@ #define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */ #define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */ #define SSB_SPROM1_BINF_CCODE_SHIFT 8 -#define SSB_SPROM1_BINF_ANTA 0x3000 /* Available A-PHY antennas */ -#define SSB_SPROM1_BINF_ANTA_SHIFT 12 -#define SSB_SPROM1_BINF_ANTBG 0xC000 /* Available B-PHY antennas */ -#define SSB_SPROM1_BINF_ANTBG_SHIFT 14 +#define SSB_SPROM1_BINF_ANTBG 0x3000 /* Available B-PHY and G-PHY antennas */ +#define SSB_SPROM1_BINF_ANTBG_SHIFT 12 +#define SSB_SPROM1_BINF_ANTA 0xC000 /* Available A-PHY antennas */ +#define SSB_SPROM1_BINF_ANTA_SHIFT 14 #define SSB_SPROM1_PA0B0 0x105E #define SSB_SPROM1_PA0B1 0x1060 #define SSB_SPROM1_PA0B2 0x1062 @@ -212,10 +221,11 @@ #define SSB_SPROM1_ITSSI_A_SHIFT 8 #define SSB_SPROM1_BFLLO 0x1072 /* Boardflags (low 16 bits) */ #define SSB_SPROM1_AGAIN 0x1074 /* Antenna Gain (in dBm Q5.2) */ -#define SSB_SPROM1_AGAIN_A 0x00FF /* A-PHY */ -#define SSB_SPROM1_AGAIN_BG 0xFF00 /* B-PHY and G-PHY */ -#define SSB_SPROM1_AGAIN_BG_SHIFT 8 -#define SSB_SPROM1_OEM 0x1076 /* 8 bytes OEM string (rev 1 only) */ +#define SSB_SPROM1_AGAIN_BG 0x00FF /* B-PHY and G-PHY */ +#define SSB_SPROM1_AGAIN_BG_SHIFT 0 +#define SSB_SPROM1_AGAIN_A 0xFF00 /* A-PHY */ +#define SSB_SPROM1_AGAIN_A_SHIFT 8 + /* SPROM Revision 2 (inherits from rev 1) */ #define SSB_SPROM2_BFLHI 0x1038 /* Boardflags (high 16 bits) */ #define SSB_SPROM2_MAXP_A 0x103A /* A-PHY Max Power */ @@ -232,7 +242,11 @@ #define SSB_SPROM2_OPO_VALUE 0x00FF #define SSB_SPROM2_OPO_UNUSED 0xFF00 #define SSB_SPROM2_CCODE 0x107C /* Two char Country Code */ -/* SPROM Revision 3 (inherits from rev 2) */ + +/* SPROM Revision 3 (inherits most data from rev 2) */ +#define SSB_SPROM3_IL0MAC 0x104A /* 6 bytes MAC address for 802.11b/g */ +#define SSB_SPROM3_ET0MAC 0x1050 /* 6 bytes MAC address for Ethernet ?? */ +#define SSB_SPROM3_ET1MAC 0x1050 /* 6 bytes MAC address for 802.11a ?? */ #define SSB_SPROM3_OFDMAPO 0x102C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */ #define SSB_SPROM3_OFDMALPO 0x1030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */ #define SSB_SPROM3_OFDMAHPO 0x1034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */ @@ -251,6 +265,57 @@ #define SSB_SPROM3_CCKPO_11M_SHIFT 12 #define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */ +/* SPROM Revision 4 */ +#define SSB_SPROM4_IL0MAC 0x104C /* 6 byte MAC address for a/b/g/n */ +#define SSB_SPROM4_ET0MAC 0x1018 /* 6 bytes MAC address for Ethernet ?? */ +#define SSB_SPROM4_ET1MAC 0x1018 /* 6 bytes MAC address for 802.11a ?? */ +#define SSB_SPROM4_ETHPHY 0x105A /* Ethernet PHY settings ?? */ +#define SSB_SPROM4_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ +#define SSB_SPROM4_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ +#define SSB_SPROM4_ETHPHY_ET1A_SHIFT 5 +#define SSB_SPROM4_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ +#define SSB_SPROM4_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ +#define SSB_SPROM4_CCODE 0x1052 /* Country Code (2 bytes) */ +#define SSB_SPROM4_ANTAVAIL 0x105D /* Antenna available bitfields */ +#define SSB_SPROM4_ANTAVAIL_A 0x00FF /* A-PHY bitfield */ +#define SSB_SPROM4_ANTAVAIL_A_SHIFT 0 +#define SSB_SPROM4_ANTAVAIL_BG 0xFF00 /* B-PHY and G-PHY bitfield */ +#define SSB_SPROM4_ANTAVAIL_BG_SHIFT 8 +#define SSB_SPROM4_BFLLO 0x1044 /* Boardflags (low 16 bits) */ +#define SSB_SPROM4_AGAIN01 0x105E /* Antenna Gain (in dBm Q5.2) */ +#define SSB_SPROM4_AGAIN0 0x00FF /* Antenna 0 */ +#define SSB_SPROM4_AGAIN0_SHIFT 0 +#define SSB_SPROM4_AGAIN1 0xFF00 /* Antenna 1 */ +#define SSB_SPROM4_AGAIN1_SHIFT 8 +#define SSB_SPROM4_AGAIN23 0x1060 +#define SSB_SPROM4_AGAIN2 0x00FF /* Antenna 2 */ +#define SSB_SPROM4_AGAIN2_SHIFT 0 +#define SSB_SPROM4_AGAIN3 0xFF00 /* Antenna 3 */ +#define SSB_SPROM4_AGAIN3_SHIFT 8 +#define SSB_SPROM4_BFLHI 0x1046 /* Board Flags Hi */ +#define SSB_SPROM4_MAXP_BG 0x1080 /* Max Power BG in path 1 */ +#define SSB_SPROM4_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */ +#define SSB_SPROM4_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */ +#define SSB_SPROM4_ITSSI_BG_SHIFT 8 +#define SSB_SPROM4_MAXP_A 0x108A /* Max Power A in path 1 */ +#define SSB_SPROM4_MAXP_A_MASK 0x00FF /* Mask for Max Power A */ +#define SSB_SPROM4_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */ +#define SSB_SPROM4_ITSSI_A_SHIFT 8 +#define SSB_SPROM4_GPIOA 0x1056 /* Gen. Purpose IO # 0 and 1 */ +#define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */ +#define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */ +#define SSB_SPROM4_GPIOA_P1_SHIFT 8 +#define SSB_SPROM4_GPIOB 0x1058 /* Gen. Purpose IO # 2 and 3 */ +#define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */ +#define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */ +#define SSB_SPROM4_GPIOB_P3_SHIFT 8 +#define SSB_SPROM4_PA0B0 0x1082 /* The paXbY locations are */ +#define SSB_SPROM4_PA0B1 0x1084 /* only guesses */ +#define SSB_SPROM4_PA0B2 0x1086 +#define SSB_SPROM4_PA1B0 0x108E +#define SSB_SPROM4_PA1B1 0x1090 +#define SSB_SPROM4_PA1B2 0x1092 + /* Values for SSB_SPROM1_BINF_CCODE */ enum { SSB_SPROM1CCODE_WORLD = 0, |