diff options
Diffstat (limited to 'package/boot/uboot-xburst/files/include/configs')
5 files changed, 755 insertions, 0 deletions
diff --git a/package/boot/uboot-xburst/files/include/configs/avt2.h b/package/boot/uboot-xburst/files/include/configs/avt2.h new file mode 100644 index 0000000..cbf34d7 --- /dev/null +++ b/package/boot/uboot-xburst/files/include/configs/avt2.h @@ -0,0 +1,26 @@ +#ifndef __CONFIG_AVT2_H +#define __CONFIG_AVT2_H + +#include <configs/nanonote.h> + +#define CONFIG_AVT2 1 + +#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait avt2=1" +#define CONFIG_BOOTARGSFROMSD "mem=64M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait avt2=1" +#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" + +/* SDRAM paramters */ +#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */ +#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ +#define SDRAM_ROW 13 /* Row address: 11 to 13 */ +#define SDRAM_COL 10 /* Column address: 8 to 12 */ +#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ + +/* SDRAM Timings, unit: ns */ +#define SDRAM_TRAS 45 /* RAS# Active Time */ +#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ +#define SDRAM_TPC 20 /* RAS# Precharge Time */ +#define SDRAM_TRWL 7 /* Write Latency Time */ +#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */ + +#endif /* __CONFIG_AVT_H */ diff --git a/package/boot/uboot-xburst/files/include/configs/n516.h b/package/boot/uboot-xburst/files/include/configs/n516.h new file mode 100644 index 0000000..c741bfe --- /dev/null +++ b/package/boot/uboot-xburst/files/include/configs/n516.h @@ -0,0 +1,311 @@ +/* + * (C) Copyright 2006 + * Ingenic Semiconductor, <jlwei@ingenic.cn> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * This file contains the configuration parameters for the pavo board. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +//#define DEBUG +//#define DEBUG_SHELL + +#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ +#define CONFIG_JzRISC 1 /* JzRISC core */ +#define CONFIG_JZSOC 1 /* Jz SoC */ +#define CONFIG_JZ4740 1 /* Jz4740 SoC */ +#define CONFIG_PAVO 1 /* PAVO validation board */ + +#define CONFIG_BOARD_NAME "n516" +#define CONFIG_BOARD_HWREV "1.0" +#define CONFIG_FIRMWARE_EPOCH "0" +#define CONFIG_UPDATE_TMPBUF 0x80600000 +#define CONFIG_UPDATE_CHUNKSIZE 0x800000 +#define CONFIG_UPDATE_FILENAME "update.oifw" +#define CONFIG_UPDATE_FILEEXT ".oifw" +#define CONFIG_UBI_PARTITION "UBI" + +#define CONFIG_SKIP_LOWLEVEL_INIT 1 +#undef CONFIG_SKIP_RELOCATE_UBOOT + +#if 0 +#define CONFIG_LCD /* LCD support */ +#define CONFIG_JZLCD_METRONOME_800x600 +#define LCD_BPP LCD_COLOR8 + +#define WFM_DATA_SIZE ( 1 << 14 ) +#define CONFIG_METRONOME_WF_LEN (64 * (1 << 10)) +#define CONFIG_METRONOME_WF_NAND_OFFSET (0x100000) +#define BMP_LOGO_HEIGHT 0 +#define CONFIG_UBI_WF_VOLUME "waveforms" +#define CONFIG_UBI_BOOTSPLASH_VOLUME "bootsplash" +#define CONFIG_METRONOME_BOOTSPLASH_LEN 480000 +#endif + +#if 0 +#define CONFIG_JZSOC_I2C +#define CONFIG_HARD_I2C +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0 +#define CONFIG_LPC_I2C_ADDR 0x54 +#endif + +#define JZ4740_NORBOOT_CFG JZ4740_NORBOOT_16BIT /* NOR Boot config code */ +#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 /* NAND Boot config code */ + +#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */ +#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */ +#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL/256) /* incrementer freq */ + +#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */ + +#define CONFIG_BAUDRATE 57600 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + + +#define CONFIG_MMC 1 +#define CONFIG_GENERIC_MMC 1 +#define CONFIG_JZ_MMC 1 +#define CONFIG_FAT 1 + +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 ">" +#define CONFIG_CMDLINE_EDITING + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +#include <config_cmd_default.h> + +#undef CONFIG_CMD_BDI /* bdinfo */ +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_ECHO /* echo arguments */ +#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ +#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ +#undef CONFIG_CMD_IMI /* iminfo */ +#undef CONFIG_CMD_ITEST /* Integer (and string) test */ +#undef CONFIG_CMD_LOADB /* loadb */ +#undef CONFIG_CMD_LOADS /* loads */ +#undef CONFIG_CMD_NFS /* NFS support */ +#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ +#undef CONFIG_CMD_SOURCE /* "source" command support */ +#undef CONFIG_CMD_XIMG /* Load part of Multi Image */ +#undef CONFIG_CMD_NET + +//#define CONFIG_CMD_ASKENV +//#define CONFIG_CMD_DHCP +//#define CONFIG_CMD_PING +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MMC +#define CONFIG_CMD_FAT +/*#define CONFIG_CMD_UBI*/ +/*#define CONFIG_CMD_MTDPARTS*/ +//#define CONFIG_CMD_JFFS2 +//#define CONFIG_JFFS2_NAND +//#define CONFIG_JFFS2_CMDLINE +#define CONFIG_CMD_UPDATE + +#define CONFIG_DOS_PARTITION + +/*#define CONFIG_MTD_PARTITIONS*/ +#define CONFIG_RBTREE + +#define CONFIG_BOOTP_MASK ( CONFIG_BOOTP_DEFAUL ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#if 0 +#define CONFIG_ZERO_BOOTDELAY_CHECK +#define CONFIG_BOOTDELAY 0 +#define CONFIG_BOOTFILE uImage /* file to load */ +#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ip=off rootfstype=ubifs root=ubi:rootfs ubi.mtd=UBI rw panic=5 " MTDPARTS_DEFAULT +#define CONFIG_BOOTCOMMAND "check_and_update; setenv bootargs $bootargs $batt_level_param; ubi read 0x80600000 bootsplash && show_image 0x80600000; ubi read 0x80600000 kernel; bootm 0x80600000; ubi read 0x80600000 errorsplash && show_image 0x80600000; while test 0 = 0; do check_and_update; done" +#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */ +#define CONFIG_IPADDR 192.168.111.1 +#define CONFIG_SERVERIP 192.168.111.2 +#define MTDIDS_DEFAULT "nand0=jz4740-nand" +#define MTDPARTS_DEFAULT "mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)" +#define CONFIG_EXTRA_ENV_SETTINGS "mtdids=nand0=jz4740-nand\0mtdparts=mtdparts=jz4740-nand:1M@0(uboot)ro,-@1M(UBI)\0" \ + "stdout=serial\0stderr=lcd\0" +#endif + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL) +#define CONFIG_BOOTDELAY 0 +#define CONFIG_BOOTFILE "uImage" /* file to load */ +#define CONFIG_BOOTARGS "mem=64M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait" +#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" + + + +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +/* + * Serial download configuration + * + */ +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "n516 # " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ + +#define CONFIG_SYS_MALLOC_LEN 1024*1024*2 +#define CONFIG_SYS_BOOTPARAMS_LEN 128*1024 + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */ + +#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 + +#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */ + +#define CONFIG_SYS_MEMTEST_START 0x80100000 +#define CONFIG_SYS_MEMTEST_END 0x80800000 + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else +#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#endif + +/*----------------------------------------------------------------------- + * NAND FLASH configuration + */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_BASE 0xB8000000 +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ + +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 8k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 8kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */ +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ + +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) /* NAND chip block size */ +#define CONFIG_SYS_NAND_BADBLOCK_PAGE 63 /* NAND bad block was marked at this page in a block, starting from 0 */ +#define CONFIG_SYS_NAND_ECC_POS 6 + +#ifdef CONFIG_ENV_IS_IN_NAND +//#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_SIZE (128 * 1024) +//#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) /* environment starts here */ +#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_U_BOOT_OFFS) +//#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#endif + + +/*----------------------------------------------------------------------- + * NOR FLASH and environment organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT (128) /* max number of sectors on one chip */ + +#define PHYS_FLASH_1 0xa8000000 /* Flash Bank #1 */ + +/* The following #defines are needed to get flash environment right */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* in pavo/config.mk TEXT_BASE=0x88000000*/ +#define CONFIG_SYS_SYS_MONITOR_BASE TEXT_BASE /* in pavo/config.mk TEXT_BASE=0x88000000*/ +#define CONFIG_SYS_MONITOR_LEN (256*1024) /* Reserve 256 kB for Monitor */ + +#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 + +/* timeout values are in ticks */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (2 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */ +#define CONFIG_SYS_FLASH_WRITE_TOUT (2 * CONFIG_SYS_HZ) /* Timeout for Flash Write */ + +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_IS_NOWHERE 1 +#define CONFIG_ENV_ADDR 0xa8040000 +#define CONFIG_ENV_SIZE 0x20000 +#endif + +/*----------------------------------------------------------------------- + * SDRAM Info. + */ +#define CONFIG_NR_DRAM_BANKS 1 + +// SDRAM paramters +#define SDRAM_BW16 0 /* Data bus width: 0-32bit, 1-16bit */ +#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ +#define SDRAM_ROW 13 /* Row address: 11 to 13 */ +#define SDRAM_COL 9 /* Column address: 8 to 12 */ +#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ + +// SDRAM Timings, unit: ns +#define SDRAM_TRAS 45 /* RAS# Active Time */ +#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ +#define SDRAM_TPC 20 /* RAS# Precharge Time */ +#define SDRAM_TRWL 7 /* Write Latency Time */ +#define SDRAM_TREF 15625 /* Refresh period: 4096 refresh cycles/64ms */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_DCACHE_SIZE 16384 +#define CONFIG_SYS_ICACHE_SIZE 16384 +#define CONFIG_SYS_CACHELINE_SIZE 32 + +/*----------------------------------------------------------------------- + * GPIO definition + */ +#define GPIO_SD_VCC_EN_N 113 /* GPD17 */ +#define GPIO_SD_CD_N 103 /* GPD7 */ +#define GPIO_SD_WP 111 /* GPD15 */ +#define GPIO_USB_DETE 115 /* GPD6 */ +//#define GPIO_DC_DETE_N 103 /* GPD7 */ +#define GPIO_CHARG_STAT_N 112 /* GPD15 */ +#define GPIO_DISP_OFF_N 97 /* GPD1 */ +#define GPIO_UDC_HOTPLUG 100 /* GPD4 */ +#define GPIO_LED_EN 124 /* GPD28 */ + +#define GPIO_RST_L 50 /* GPB18 LCD_SPL */ +#define GPIO_LCDRDY 49 /* GPB17 LCD_CLS */ +#define GPIO_STBY 86 /* GPC22 LCD_PS */ +#define GPIO_ERR 87 /* GPC23 LCD_REV */ + +#endif /* __CONFIG_H */ diff --git a/package/boot/uboot-xburst/files/include/configs/nanonote.h b/package/boot/uboot-xburst/files/include/configs/nanonote.h new file mode 100644 index 0000000..8926877 --- /dev/null +++ b/package/boot/uboot-xburst/files/include/configs/nanonote.h @@ -0,0 +1,191 @@ +/* + * Authors: Xiangfu Liu <xiangfu.z@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 3 of the License, or (at your option) any later version. + */ + +/* + * This file contains the configuration parameters for the NanoNote. + */ +#ifndef __CONFIG_NANONOTE_H +#define __CONFIG_NANONOTE_H + +#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ +#define CONFIG_JzRISC 1 /* JzRISC core */ +#define CONFIG_JZSOC 1 /* Jz SoC */ +#define CONFIG_JZ4740 1 /* Jz4740 SoC */ +#define CONFIG_NANONOTE 1 + +#define CONFIG_LCD 1 /* LCD support */ +#define LCD_BPP LCD_COLOR32 /*5:18,24,32 bits per pixel */ +#define CONFIG_SYS_WHITE_ON_BLACK 1 + +#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */ +#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */ +#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */ +#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED + +#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */ +#define CONFIG_BAUDRATE 57600 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_MMC 1 +#define CONFIG_FAT 1 +#define CONFIG_DOS_PARTITION 1 +#define CONFIG_SKIP_LOWLEVEL_INIT 1 +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_SYS_NO_FLASH 1 +#define CONFIG_ENV_OVERWRITE 1 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL) +#define CONFIG_BOOTDELAY 0 +#define CONFIG_BOOTFILE "uImage" /* file to load */ +/* + * Command line configuration. + */ +#define CONFIG_CMD_BOOTD /* bootd */ +#define CONFIG_CMD_CONSOLE /* coninfo */ +#define CONFIG_CMD_ECHO /* echo arguments */ + +#define CONFIG_CMD_LOADB /* loadb */ +#define CONFIG_CMD_LOADS /* loads */ +#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */ +#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/ +#define CONFIG_CMD_RUN /* run command in env variable */ +#define CONFIG_CMD_SAVEENV /* saveenv */ +#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ +#define CONFIG_CMD_SOURCE /* "source" command support */ + +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MMC +#define CONFIG_CMD_FAT + +/* + * Serial download configuration + */ +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "QI# " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +/* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ + +#define CONFIG_SYS_MALLOC_LEN 896 * 1024 +#define CONFIG_SYS_BOOTPARAMS_LEN 128 * 1024 + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */ +#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 +#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */ +#define CONFIG_SYS_MEMTEST_START 0x80100000 +#define CONFIG_SYS_MEMTEST_END 0x80800000 + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ + +/* + * NAND FLASH configuration + */ +/* NAND Boot config code */ +#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 + +#define NANONOTE_NAND_SIZE 2 /* if board nand flash is 1GB, set to 1 + * if board nand flash is 2GB, set to 2 + * for change the PAGE_SIZE and BLOCK_SIZE + * will delete when there is no 1GB flash + */ + +#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * NANONOTE_NAND_SIZE) +/* nand chip block size */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * NANONOTE_NAND_SIZE << 10) +/* nand bad block was marked at this page in a block, start from 0 */ +#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127 +/* ECC offset position in oob area, default value is 6 if it isn't defined */ +#define CONFIG_SYS_NAND_ECC_POS (6 * NANONOTE_NAND_SIZE) +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_BASE 0xB8000000 +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/ +#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE + +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 8k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 8kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */ +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST +/* Start NUB from this addr*/ + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ + +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) +/* environment starts here */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) + +/* in board/nanonote/config.mk TEXT_BAS = 0x88000000 */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE + +/* + * SDRAM Info. + */ +#define CONFIG_NR_DRAM_BANKS 1 + +/* + * Cache Configuration + */ +#define CONFIG_SYS_DCACHE_SIZE 16384 +#define CONFIG_SYS_ICACHE_SIZE 16384 +#define CONFIG_SYS_CACHELINE_SIZE 32 + +/* + * GPIO definition + */ +#define GPIO_LCD_CS (2 * 32 + 21) +#define GPIO_DISP_OFF_N (3 * 32 + 21) +#define GPIO_PWM (3 * 32 + 27) + +#define GPIO_AMP_EN (3 * 32 + 4) + +#define GPIO_SDPW_EN (3 * 32 + 2) +#define GPIO_SD_DETECT (3 * 32 + 0) + +#define GPIO_USB_DETECT (3 * 32 + 27) +#define GPIO_BUZZ_PWM (3 * 32 + 28) + +#define GPIO_AUDIO_POP (1 * 32 + 29) +#define GPIO_COB_TEST (1 * 32 + 30) + +#define GPIO_KEYOUT_BASE (2 * 32 + 10) +#define GPIO_KEYIN_BASE (3 * 32 + 18) +#define GPIO_KEYIN_8 (3 * 32 + 26) + +#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */ +#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */ + +#endif /* __CONFIG_NANONOTE_H */ diff --git a/package/boot/uboot-xburst/files/include/configs/qi_lb60.h b/package/boot/uboot-xburst/files/include/configs/qi_lb60.h new file mode 100644 index 0000000..1542c3d --- /dev/null +++ b/package/boot/uboot-xburst/files/include/configs/qi_lb60.h @@ -0,0 +1,27 @@ +#ifndef __CONFIG_QI_LB60_H +#define __CONFIG_QI_LB60_H + +#include <configs/nanonote.h> + +#define CONFIG_QI_LB60 1 + +#define CONFIG_BOOTARGS "mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait" +#define CONFIG_BOOTARGSFROMSD "mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p2 rw rootwait" +#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" +#define CONFIG_BOOTCOMMANDFROMSD "mmc init; fatload mmc 0 0x80600000 uImage; bootm" + +/* SDRAM paramters */ +#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */ +#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ +#define SDRAM_ROW 13 /* Row address: 11 to 13 */ +#define SDRAM_COL 9 /* Column address: 8 to 12 */ +#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ + +/* SDRAM Timings, unit: ns */ +#define SDRAM_TRAS 45 /* RAS# Active Time */ +#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ +#define SDRAM_TPC 20 /* RAS# Precharge Time */ +#define SDRAM_TRWL 7 /* Write Latency Time */ +#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */ + +#endif diff --git a/package/boot/uboot-xburst/files/include/configs/sakc.h b/package/boot/uboot-xburst/files/include/configs/sakc.h new file mode 100644 index 0000000..b88d8b0 --- /dev/null +++ b/package/boot/uboot-xburst/files/include/configs/sakc.h @@ -0,0 +1,200 @@ +/* + * Authors: Xiangfu Liu <xiangfu.z@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 3 of the License, or (at your option) any later version. + */ + +/* + * This file contains the configuration parameters for SAKC. + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#define DEBUG +#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ +#define CONFIG_JzRISC 1 /* JzRISC core */ +#define CONFIG_JZSOC 1 /* Jz SoC */ +#define CONFIG_JZ4725 1 /* Jz4725 SoC */ +#define CONFIG_JZ4740 1 /* Jz4740 SoC */ +#define CONFIG_SAKC 1 /* SAKC board */ + +#define MMC_BUS_WIDTH_1BIT 1 /* 1 for MMC 1Bit Bus Width */ + +//#define CONFIG_LCD 1 /* LCD support */ +//#define LCD_BPP LCD_COLOR32 /*5:18,24,32 bits per pixel */ +//#define CONFIG_SYS_WHITE_ON_BLACK 1 + +#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */ +#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */ +#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */ +#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED + +#define CONFIG_SYS_UART_BASE UART0_BASE /* Base of the UART channel */ +#define CONFIG_BAUDRATE 57600 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_MMC 1 +#define CONFIG_FAT 1 +#define CONFIG_DOS_PARTITION 1 +#define CONFIG_SKIP_LOWLEVEL_INIT 1 +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_SYS_NO_FLASH 1 +#define CONFIG_ENV_OVERWRITE 1 + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL) +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTFILE "uImage" /* file to load */ +#define CONFIG_BOOTARGS "mem=32M console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait" +#define CONFIG_EXTRA_ENV_SETTINGS 1 +#define CONFIG_BOOTARGSFROMSD "mem=32M console=ttyS0,57600n8 rootfstype=ext2 root=/dev/mmcblk0p1 rw rootwait" +#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm" + +/* + * Command line configuration. + */ +#define CONFIG_CMD_BDI /* bdinfo */ +#define CONFIG_CMD_BOOTD /* bootd */ +#define CONFIG_CMD_CONSOLE /* coninfo */ +#define CONFIG_CMD_ECHO /* echo arguments */ +#define CONFIG_CMD_IMI /* iminfo */ +#define CONFIG_CMD_ITEST /* Integer (and string) test */ + +#define CONFIG_CMD_LOADB /* loadb */ +#define CONFIG_CMD_LOADS /* loads */ +#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */ +#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/ +#define CONFIG_CMD_RUN /* run command in env variable */ +#define CONFIG_CMD_SAVEENV /* saveenv */ +#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ +#define CONFIG_CMD_SOURCE /* "source" command support */ +#define CONFIG_CMD_XIMG /* Load part of Multi Image */ + +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MMC +#define CONFIG_CMD_FAT + +/* + * Serial download configuration + */ +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "SAKC# " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +/* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/ + +#define CONFIG_SYS_MALLOC_LEN 128 * 1024 +#define CONFIG_SYS_BOOTPARAMS_LEN 128 * 1024 + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */ +#define CONFIG_SYS_INIT_SP_OFFSET 0x400000 +#define CONFIG_SYS_LOAD_ADDR 0x80600000 /* default load address */ +#define CONFIG_SYS_MEMTEST_START 0x80100000 +#define CONFIG_SYS_MEMTEST_END 0x80800000 + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ + +/* + * NAND FLASH configuration + */ +/* NAND Boot config code */ +#define JZ4740_NANDBOOT_CFG JZ4740_NANDBOOT_B8R3 + +#define SAKC_NAND_SIZE 1 /* if board nand flash is 1GB, set to 1 + * if board nand flash is 2GB, set to 2 + * for change the PAGE_SIZE and BLOCK_SIZE + * will delete when there is no 1GB flash + */ + +#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * SAKC_NAND_SIZE) +/* nand chip block size */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * SAKC_NAND_SIZE << 10) +/* nand bad block was marked at this page in a block, start from 0 */ +#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127 +/* ECC offset position in oob area, default value is 6 if it isn't defined */ +#define CONFIG_SYS_NAND_ECC_POS (6 * SAKC_NAND_SIZE) +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_BASE 0xB8000000 +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/ +#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE + +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 8k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 8kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */ +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST +/* Start NUB from this addr*/ + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ + +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE + CONFIG_SYS_NAND_BLOCK_SIZE) +/* environment starts here */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) + +/* in qi_lb60.h/config.mk TEXT_BAS = 0x88000000 */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE + +/* + * SDRAM Info. + */ +#define CONFIG_NR_DRAM_BANKS 1 + +/* SDRAM paramters */ +#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */ +#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */ +#define SDRAM_ROW 13 /* Row address: 11 to 13 */ +#define SDRAM_COL 9 /* Column address: 8 to 12 */ +#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */ + +/* SDRAM Timings, unit: ns */ +#define SDRAM_TRAS 45 /* RAS# Active Time */ +#define SDRAM_RCD 20 /* RAS# to CAS# Delay */ +#define SDRAM_TPC 20 /* RAS# Precharge Time */ +#define SDRAM_TRWL 7 /* Write Latency Time */ +#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */ + +/* + * Cache Configuration + */ +#define CONFIG_SYS_DCACHE_SIZE 16384 +#define CONFIG_SYS_ICACHE_SIZE 16384 +#define CONFIG_SYS_CACHELINE_SIZE 32 + +/* + * GPIO definition + */ +#define GPIO_SD_DETECT (2 * 32 + 27) +#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */ +#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */ + +#endif /* __CONFIG_H */ |