diff options
Diffstat (limited to 'package/iw/patches/001-nl80211_h_sync.patch')
| -rw-r--r-- | package/iw/patches/001-nl80211_h_sync.patch | 274 |
1 files changed, 50 insertions, 224 deletions
diff --git a/package/iw/patches/001-nl80211_h_sync.patch b/package/iw/patches/001-nl80211_h_sync.patch index 1c42527..544df9d 100644 --- a/package/iw/patches/001-nl80211_h_sync.patch +++ b/package/iw/patches/001-nl80211_h_sync.patch @@ -1,251 +1,77 @@ --- a/nl80211.h +++ b/nl80211.h -@@ -6,7 +6,7 @@ - * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net> - * Copyright 2008 Michael Wu <flamingice@sourmilk.net> - * Copyright 2008 Luis Carlos Cobo <luisca@cozybit.com> -- * Copyright 2008 Michael Buesch <mb@bu3sch.de> -+ * Copyright 2008 Michael Buesch <m@bues.ch> - * Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com> - * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com> - * Copyright 2008 Colin McCabe <colin@cozybit.com> -@@ -161,6 +161,13 @@ - * @NL80211_CMD_SET_BEACON: set the beacon on an access point interface - * using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD, - * %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes. -+ * Following attributes are provided for drivers that generate full Beacon -+ * and Probe Response frames internally: %NL80211_ATTR_SSID, -+ * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE, -+ * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS, -+ * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY, -+ * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_IE, %NL80211_ATTR_IE_PROBE_RESP, -+ * %NL80211_ATTR_IE_ASSOC_RESP. - * @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface, - * parameters are like for %NL80211_CMD_SET_BEACON. - * @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it -@@ -762,6 +769,8 @@ enum nl80211_commands { - * that can be added to a scan request - * @NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN: maximum length of information - * elements that can be added to a scheduled scan request -+ * @NL80211_ATTR_MAX_MATCH_SETS: maximum number of sets that can be -+ * used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute. - * - * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz) - * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive -@@ -842,18 +851,20 @@ enum nl80211_commands { - * @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT - * event (u16) - * @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating -- * that protected APs should be used. -+ * that protected APs should be used. This is also used with NEW_BEACON to -+ * indicate that the BSS is to use protection. - * -- * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT and ASSOCIATE to -- * indicate which unicast key ciphers will be used with the connection -+ * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT, ASSOCIATE, and NEW_BEACON -+ * to indicate which unicast key ciphers will be used with the connection - * (an array of u32). -- * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT and ASSOCIATE to indicate -- * which group key cipher will be used with the connection (a u32). -- * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT and ASSOCIATE to indicate -- * which WPA version(s) the AP we want to associate with is using -+ * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT, ASSOCIATE, and NEW_BEACON to -+ * indicate which group key cipher will be used with the connection (a -+ * u32). -+ * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT, ASSOCIATE, and NEW_BEACON to -+ * indicate which WPA version(s) the AP we want to associate with is using - * (a u32 with flags from &enum nl80211_wpa_versions). -- * @NL80211_ATTR_AKM_SUITES: Used with CONNECT and ASSOCIATE to indicate -- * which key management algorithm(s) to use (an array of u32). -+ * @NL80211_ATTR_AKM_SUITES: Used with CONNECT, ASSOCIATE, and NEW_BEACON to -+ * indicate which key management algorithm(s) to use (an array of u32). - * - * @NL80211_ATTR_REQ_IE: (Re)association request information elements as - * sent out by the card, for ROAM and successful CONNECT events. -@@ -1002,6 +1013,24 @@ enum nl80211_commands { +@@ -1475,6 +1475,7 @@ enum nl80211_attrs { + #define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS - * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan - * cycles, in msecs. -+ -+ * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more -+ * sets of attributes to match during scheduled scans. Only BSSs -+ * that match any of the sets will be reported. These are -+ * pass-thru filter rules. -+ * For a match to succeed, the BSS must match all attributes of a -+ * set. Since not every hardware supports matching all types of -+ * attributes, there is no guarantee that the reported BSSs are -+ * fully complying with the match sets and userspace needs to be -+ * able to ignore them by itself. -+ * Thus, the implementation is somewhat hardware-dependent, but -+ * this is only an optimization and the userspace application -+ * needs to handle all the non-filtered results anyway. -+ * If the match attributes don't make sense when combined with -+ * the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID -+ * is included in the probe request, but the match attributes -+ * will never let it go through), -EINVAL may be returned. -+ * If ommited, no filtering is done. - * - * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported - * interface combinations. In each nested item, it contains attributes -@@ -1014,6 +1043,33 @@ enum nl80211_commands { - * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information - * necessary for GTK rekeying in the device, see &enum nl80211_rekey_data. - * -+ * @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan, -+ * nested array attribute containing an entry for each band, with the entry -+ * being a list of supported rates as defined by IEEE 802.11 7.3.2.2 but -+ * without the length restriction (at most %NL80211_MAX_SUPP_RATES). -+ * -+ * @NL80211_ATTR_HIDDEN_SSID: indicates whether SSID is to be hidden from Beacon -+ * and Probe Response (when response to wildcard Probe Request); see -+ * &enum nl80211_hidden_ssid, represented as a u32 -+ * -+ * @NL80211_ATTR_IE_PROBE_RESP: Information element(s) for Probe Response frame. -+ * This is used with %NL80211_CMD_NEW_BEACON and %NL80211_CMD_SET_BEACON to -+ * provide extra IEs (e.g., WPS/P2P IE) into Probe Response frames when the -+ * driver (or firmware) replies to Probe Request frames. -+ * @NL80211_ATTR_IE_ASSOC_RESP: Information element(s) for (Re)Association -+ * Response frames. This is used with %NL80211_CMD_NEW_BEACON and -+ * %NL80211_CMD_SET_BEACON to provide extra IEs (e.g., WPS/P2P IE) into -+ * (Re)Association Response frames when the driver (or firmware) replies to -+ * (Re)Association Request frames. -+ * -+ * @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration -+ * of the station, see &enum nl80211_sta_wme_attr. -+ * @NL80211_ATTR_SUPPORT_AP_UAPSD: the device supports uapsd when working -+ * as AP. -+ * -+ * @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of -+ * roaming to another AP in the same ESS if the signal lever is low. -+ * - * @NL80211_ATTR_MAX: highest attribute number currently defined - * @__NL80211_ATTR_AFTER_LAST: internal use + #define NL80211_MAX_SUPP_RATES 32 ++#define NL80211_MAX_SUPP_HT_RATES 77 + #define NL80211_MAX_SUPP_REG_RULES 32 + #define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0 + #define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16 +@@ -1536,7 +1537,11 @@ enum nl80211_iftype { + * @NL80211_STA_FLAG_WME: station is WME/QoS capable + * @NL80211_STA_FLAG_MFP: station uses management frame protection + * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated +- * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer ++ * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should ++ * only be used in managed mode (even in the flags mask). Note that the ++ * flag can't be changed, it is only valid while adding a station, and ++ * attempts to change it will silently be ignored (rather than rejected ++ * as errors.) + * @NL80211_STA_FLAG_MAX: highest station flag number currently defined + * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ -@@ -1217,6 +1273,21 @@ enum nl80211_attrs { - NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS, - NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN, - -+ NL80211_ATTR_SCAN_SUPP_RATES, -+ -+ NL80211_ATTR_HIDDEN_SSID, -+ -+ NL80211_ATTR_IE_PROBE_RESP, -+ NL80211_ATTR_IE_ASSOC_RESP, -+ -+ NL80211_ATTR_STA_WME, -+ NL80211_ATTR_SUPPORT_AP_UAPSD, -+ -+ NL80211_ATTR_ROAM_SUPPORT, -+ -+ NL80211_ATTR_SCHED_SCAN_MATCH, -+ NL80211_ATTR_MAX_MATCH_SETS, -+ - /* add attributes here, update the policy in nl80211.c */ - - __NL80211_ATTR_AFTER_LAST, -@@ -1426,6 +1497,8 @@ enum nl80211_sta_bss_param { - * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute +@@ -1651,6 +1656,9 @@ enum nl80211_sta_bss_param { * containing info as possible, see &enum nl80211_sta_bss_param * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected + * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update. ++ * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32) + * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU + * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ -@@ -1447,6 +1520,8 @@ enum nl80211_sta_info { - NL80211_STA_INFO_RX_BITRATE, +@@ -1673,6 +1681,9 @@ enum nl80211_sta_info { NL80211_STA_INFO_BSS_PARAM, NL80211_STA_INFO_CONNECTED_TIME, + NL80211_STA_INFO_STA_FLAGS, ++ NL80211_STA_INFO_BEACON_LOSS, + NL80211_STA_INFO_CHAIN_SIGNAL, + NL80211_STA_INFO_CHAIN_SIGNAL_AVG, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, -@@ -1676,6 +1751,26 @@ enum nl80211_reg_rule_attr { - }; - - /** -+ * enum nl80211_sched_scan_match_attr - scheduled scan match attributes -+ * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved -+ * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching, -+ * only report BSS with matching SSID. -+ * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter -+ * attribute number currently defined -+ * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use -+ */ -+enum nl80211_sched_scan_match_attr { -+ __NL80211_SCHED_SCAN_MATCH_ATTR_INVALID, -+ -+ NL80211_ATTR_SCHED_SCAN_MATCH_SSID, -+ -+ /* keep last */ -+ __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST, -+ NL80211_SCHED_SCAN_MATCH_ATTR_MAX = -+ __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1 -+}; -+ -+/** - * enum nl80211_reg_rule_flags - regulatory rule flags +@@ -2098,6 +2109,9 @@ enum nl80211_mntr_flags { + * TUs) during which a mesh STA can send only one Action frame containing a + * PERR element. * - * @NL80211_RRF_NO_OFDM: OFDM modulation not allowed -@@ -1826,6 +1921,13 @@ enum nl80211_mntr_flags { - * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a - * source mesh point for path selection elements. - * -+ * @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between -+ * root announcements are transmitted. -+ * -+ * @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has -+ * access to a broader network beyond the MBSS. This is done via Root -+ * Announcement frames. ++ * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding ++ * or forwarding entity (default is TRUE - forwarding entity) + * * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use -@@ -1847,6 +1949,8 @@ enum nl80211_meshconf_params { - NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME, - NL80211_MESHCONF_HWMP_ROOTMODE, - NL80211_MESHCONF_ELEMENT_TTL, -+ NL80211_MESHCONF_HWMP_RANN_INTERVAL, -+ NL80211_MESHCONF_GATE_ANNOUNCEMENTS, +@@ -2122,6 +2136,7 @@ enum nl80211_meshconf_params { + NL80211_MESHCONF_HWMP_RANN_INTERVAL, + NL80211_MESHCONF_GATE_ANNOUNCEMENTS, + NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL, ++ NL80211_MESHCONF_FORWARDING, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, -@@ -2423,4 +2527,37 @@ enum nl80211_rekey_data { - MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1 - }; +@@ -2395,12 +2410,15 @@ enum nl80211_key_attributes { + * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with + * 1 = 500 kbps) but without the IE length restriction (at most + * %NL80211_MAX_SUPP_RATES in a single array). ++ * @NL80211_TXRATE_MCS: HT (MCS) rates allowed for TX rate selection ++ * in an array of MCS numbers. + * @__NL80211_TXRATE_AFTER_LAST: internal + * @NL80211_TXRATE_MAX: highest TX rate attribute + */ + enum nl80211_tx_rate_attributes { + __NL80211_TXRATE_INVALID, + NL80211_TXRATE_LEGACY, ++ NL80211_TXRATE_MCS, -+/** -+ * enum nl80211_hidden_ssid - values for %NL80211_ATTR_HIDDEN_SSID -+ * @NL80211_HIDDEN_SSID_NOT_IN_USE: do not hide SSID (i.e., broadcast it in -+ * Beacon frames) -+ * @NL80211_HIDDEN_SSID_ZERO_LEN: hide SSID by using zero-length SSID element -+ * in Beacon frames -+ * @NL80211_HIDDEN_SSID_ZERO_CONTENTS: hide SSID by using correct length of SSID -+ * element in Beacon frames but zero out each byte in the SSID -+ */ -+enum nl80211_hidden_ssid { -+ NL80211_HIDDEN_SSID_NOT_IN_USE, -+ NL80211_HIDDEN_SSID_ZERO_LEN, -+ NL80211_HIDDEN_SSID_ZERO_CONTENTS -+}; -+ -+/** -+ * enum nl80211_sta_wme_attr - station WME attributes -+ * @__NL80211_STA_WME_INVALID: invalid number for nested attribute -+ * @NL80211_STA_WME_QUEUES: bitmap of uapsd queues. -+ * @NL80211_STA_WME_MAX_SP: max service period. -+ * @__NL80211_STA_WME_AFTER_LAST: internal -+ * @NL80211_STA_WME_MAX: highest station WME attribute -+ */ -+enum nl80211_sta_wme_attr { -+ __NL80211_STA_WME_INVALID, -+ NL80211_STA_WME_UAPSD_QUEUES, -+ NL80211_STA_WME_MAX_SP, -+ -+ /* keep last */ -+ __NL80211_STA_WME_AFTER_LAST, -+ NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1 -+}; -+ - #endif /* __LINUX_NL80211_H */ + /* keep last */ + __NL80211_TXRATE_AFTER_LAST, |