summaryrefslogtreecommitdiff
path: root/target/linux/adm5120/patches-3.7
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/adm5120/patches-3.7')
-rw-r--r--target/linux/adm5120/patches-3.7/001-adm5120.patch44
-rw-r--r--target/linux/adm5120/patches-3.7/002-adm5120_flash.patch21
-rw-r--r--target/linux/adm5120/patches-3.7/003-adm5120_switch.patch23
-rw-r--r--target/linux/adm5120/patches-3.7/005-adm5120_usb.patch33
-rw-r--r--target/linux/adm5120/patches-3.7/007-adm5120_pci.patch22
-rw-r--r--target/linux/adm5120/patches-3.7/009-adm5120_leds_switch_trigger.patch22
-rw-r--r--target/linux/adm5120/patches-3.7/101-cfi_fixup_macronix_bootloc.patch84
-rw-r--r--target/linux/adm5120/patches-3.7/102-jedec_pmc_39lvxxx_chips.patch68
-rw-r--r--target/linux/adm5120/patches-3.7/103-mtd_trxsplit.patch23
-rw-r--r--target/linux/adm5120/patches-3.7/120-rb153_cf_driver.patch28
-rw-r--r--target/linux/adm5120/patches-3.7/200-amba_pl010_hacks.patch355
-rw-r--r--target/linux/adm5120/patches-3.7/203-gpio_leds_brightness.patch27
-rw-r--r--target/linux/adm5120/patches-3.7/310-adm5120_wdt.patch31
13 files changed, 0 insertions, 781 deletions
diff --git a/target/linux/adm5120/patches-3.7/001-adm5120.patch b/target/linux/adm5120/patches-3.7/001-adm5120.patch
deleted file mode 100644
index 3faf8ec..0000000
--- a/target/linux/adm5120/patches-3.7/001-adm5120.patch
+++ /dev/null
@@ -1,44 +0,0 @@
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -50,6 +50,24 @@ choice
- prompt "System type"
- default SGI_IP22
-
-+config ADM5120
-+ bool "Infineon/ADMtek ADM5120 SoC based machines"
-+ select BOOT_RAW
-+ select NO_EXCEPT_FILL
-+ select CEVT_R4K
-+ select CSRC_R4K
-+ select SYS_HAS_CPU_MIPS32_R1
-+ select SYS_HAS_EARLY_PRINTK
-+ select DMA_NONCOHERENT
-+ select IRQ_CPU
-+ select SYS_SUPPORTS_LITTLE_ENDIAN
-+ select SYS_SUPPORTS_BIG_ENDIAN
-+ select SYS_SUPPORTS_32BIT_KERNEL
-+ select ARCH_REQUIRE_GPIOLIB
-+ select SWAP_IO_SPACE if CPU_BIG_ENDIAN
-+ select MIPS_MACHINE
-+ select HAVE_CLK
-+
- config MIPS_ALCHEMY
- bool "Alchemy processor based machines"
- select 64BIT_PHYS_ADDR
-@@ -855,6 +873,7 @@ config NLM_XLP_BOARD
-
- endchoice
-
-+source "arch/mips/adm5120/Kconfig"
- source "arch/mips/alchemy/Kconfig"
- source "arch/mips/ath79/Kconfig"
- source "arch/mips/bcm47xx/Kconfig"
---- a/arch/mips/Kbuild.platforms
-+++ b/arch/mips/Kbuild.platforms
-@@ -1,5 +1,6 @@
- # All platforms listed in alphabetic order
-
-+platforms += adm5120
- platforms += alchemy
- platforms += ar7
- platforms += ath79
diff --git a/target/linux/adm5120/patches-3.7/002-adm5120_flash.patch b/target/linux/adm5120/patches-3.7/002-adm5120_flash.patch
deleted file mode 100644
index 0884cf3..0000000
--- a/target/linux/adm5120/patches-3.7/002-adm5120_flash.patch
+++ /dev/null
@@ -1,21 +0,0 @@
---- a/drivers/mtd/maps/Kconfig
-+++ b/drivers/mtd/maps/Kconfig
-@@ -515,4 +515,8 @@ config MTD_LATCH_ADDR
-
- If compiled as a module, it will be called latch-addr-flash.
-
-+config MTD_ADM5120
-+ tristate "Map driver for ADM5120 based boards"
-+ depends on ADM5120
-+
- endmenu
---- a/drivers/mtd/maps/Makefile
-+++ b/drivers/mtd/maps/Makefile
-@@ -38,6 +38,7 @@ obj-$(CONFIG_MTD_SCx200_DOCFLASH)+= scx2
- obj-$(CONFIG_MTD_DBOX2) += dbox2-flash.o
- obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
- obj-$(CONFIG_MTD_PCI) += pci.o
-+obj-$(CONFIG_MTD_ADM5120) += adm5120-flash.o
- obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o
- obj-$(CONFIG_MTD_IMPA7) += impa7.o
- obj-$(CONFIG_MTD_FORTUNET) += fortunet.o
diff --git a/target/linux/adm5120/patches-3.7/003-adm5120_switch.patch b/target/linux/adm5120/patches-3.7/003-adm5120_switch.patch
deleted file mode 100644
index 970d3d6..0000000
--- a/target/linux/adm5120/patches-3.7/003-adm5120_switch.patch
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/drivers/net/Kconfig
-+++ b/drivers/net/Kconfig
-@@ -255,6 +255,10 @@ source "drivers/net/dsa/Kconfig"
-
- source "drivers/net/ethernet/Kconfig"
-
-+config ADM5120_ENET
-+ tristate "ADM5120 Ethernet switch support"
-+ depends on ADM5120
-+
- source "drivers/net/fddi/Kconfig"
-
- source "drivers/net/hippi/Kconfig"
---- a/drivers/net/Makefile
-+++ b/drivers/net/Makefile
-@@ -33,6 +33,7 @@ obj-$(CONFIG_CAN) += can/
- obj-$(CONFIG_ETRAX_ETHERNET) += cris/
- obj-$(CONFIG_NET_DSA) += dsa/
- obj-$(CONFIG_ETHERNET) += ethernet/
-+obj-$(CONFIG_ADM5120_ENET) += adm5120sw.o
- obj-$(CONFIG_FDDI) += fddi/
- obj-$(CONFIG_HIPPI) += hippi/
- obj-$(CONFIG_HAMRADIO) += hamradio/
diff --git a/target/linux/adm5120/patches-3.7/005-adm5120_usb.patch b/target/linux/adm5120/patches-3.7/005-adm5120_usb.patch
deleted file mode 100644
index 54a3cc8..0000000
--- a/target/linux/adm5120/patches-3.7/005-adm5120_usb.patch
+++ /dev/null
@@ -1,33 +0,0 @@
---- a/drivers/usb/Makefile
-+++ b/drivers/usb/Makefile
-@@ -13,6 +13,7 @@ obj-$(CONFIG_USB_DWC3) += dwc3/
- obj-$(CONFIG_USB_MON) += mon/
-
- obj-$(CONFIG_PCI) += host/
-+obj-$(CONFIG_USB_ADM5120_HCD) += host/
- obj-$(CONFIG_USB_EHCI_HCD) += host/
- obj-$(CONFIG_USB_ISP116X_HCD) += host/
- obj-$(CONFIG_USB_OHCI_HCD) += host/
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -4,6 +4,10 @@
- comment "USB Host Controller Drivers"
- depends on USB
-
-+config USB_ADM5120_HCD
-+ tristate "ADM5120 HCD support (EXPERIMENTAL)"
-+ depends on USB && ADM5120 && EXPERIMENTAL
-+
- config USB_C67X00_HCD
- tristate "Cypress C67x00 HCD support"
- depends on USB
---- a/drivers/usb/host/Makefile
-+++ b/drivers/usb/host/Makefile
-@@ -23,6 +23,7 @@ obj-$(CONFIG_USB_WHCI_HCD) += whci/
-
- obj-$(CONFIG_PCI) += pci-quirks.o
-
-+obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
- obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
- obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o
- obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
diff --git a/target/linux/adm5120/patches-3.7/007-adm5120_pci.patch b/target/linux/adm5120/patches-3.7/007-adm5120_pci.patch
deleted file mode 100644
index 2930884..0000000
--- a/target/linux/adm5120/patches-3.7/007-adm5120_pci.patch
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/arch/mips/pci/Makefile
-+++ b/arch/mips/pci/Makefile
-@@ -18,6 +18,7 @@ obj-$(CONFIG_PCI_TX4927) += ops-tx4927.o
- obj-$(CONFIG_BCM47XX) += pci-bcm47xx.o
- obj-$(CONFIG_BCM63XX) += pci-bcm63xx.o fixup-bcm63xx.o \
- ops-bcm63xx.o
-+obj-$(CONFIG_ADM5120) += pci-adm5120.o
- obj-$(CONFIG_MIPS_ALCHEMY) += pci-alchemy.o
- obj-$(CONFIG_SOC_AR71XX) += pci-ar71xx.o
- obj-$(CONFIG_PCI_AR724X) += pci-ar724x.o
---- a/include/linux/pci_ids.h
-+++ b/include/linux/pci_ids.h
-@@ -1807,6 +1807,9 @@
- #define PCI_VENDOR_ID_ESDGMBH 0x12fe
- #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
-
-+#define PCI_VENDOR_ID_ADMTEK 0x1317
-+#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120
-+
- #define PCI_VENDOR_ID_SIIG 0x131f
- #define PCI_SUBVENDOR_ID_SIIG 0x131f
- #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000
diff --git a/target/linux/adm5120/patches-3.7/009-adm5120_leds_switch_trigger.patch b/target/linux/adm5120/patches-3.7/009-adm5120_leds_switch_trigger.patch
deleted file mode 100644
index d225993..0000000
--- a/target/linux/adm5120/patches-3.7/009-adm5120_leds_switch_trigger.patch
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/drivers/leds/Kconfig
-+++ b/drivers/leds/Kconfig
-@@ -577,4 +577,12 @@ config LEDS_TRIGGER_USBDEV
- This allows LEDs to be controlled by the presence/activity of
- an USB device. If unsure, say N.
-
-+config LEDS_TRIGGER_ADM5120_SWITCH
-+ tristate "LED ADM5120 Switch Port Status Trigger"
-+ depends on LEDS_TRIGGERS && ADM5120
-+ help
-+ This allows LEDs to be controlled by the port states of
-+ the ADM5120 built-in Ethernet Switch
-+ If unsure, say N.
-+
- endif # NEW_LEDS
---- a/drivers/leds/Makefile
-+++ b/drivers/leds/Makefile
-@@ -68,3 +68,4 @@ obj-$(CONFIG_LEDS_TRIGGER_TRANSIENT) +=
- obj-$(CONFIG_LEDS_TRIGGER_MORSE) += ledtrig-morse.o
- obj-$(CONFIG_LEDS_TRIGGER_NETDEV) += ledtrig-netdev.o
- obj-$(CONFIG_LEDS_TRIGGER_USBDEV) += ledtrig-usbdev.o
-+obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o
diff --git a/target/linux/adm5120/patches-3.7/101-cfi_fixup_macronix_bootloc.patch b/target/linux/adm5120/patches-3.7/101-cfi_fixup_macronix_bootloc.patch
deleted file mode 100644
index 46ec7b6..0000000
--- a/target/linux/adm5120/patches-3.7/101-cfi_fixup_macronix_bootloc.patch
+++ /dev/null
@@ -1,84 +0,0 @@
---- a/drivers/mtd/chips/cfi_cmdset_0002.c
-+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
-@@ -48,6 +48,12 @@
- #define SST49LF008A 0x005a
- #define AT49BV6416 0x00d6
-
-+/* Macronix */
-+#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
-+#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */
-+#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
-+#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */
-+
- static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
- static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
- static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
-@@ -358,6 +364,41 @@ static struct cfi_fixup cfi_nopri_fixup_
- { 0, 0, NULL }
- };
-
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+/*
-+ * Some Macronix chips has no/bad bootblock information in the CFI table
-+ */
-+static void fixup_macronix_bootloc(struct mtd_info *mtd)
-+{
-+ struct map_info *map = mtd->priv;
-+ struct cfi_private *cfi = map->fldrv_priv;
-+ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
-+ __u8 t;
-+
-+ switch (cfi->id) {
-+ /* TODO: put affected chip ids here */
-+ case MX29LV160B:
-+ case MX29LV320B:
-+ t = 2; /* Bottom boot */
-+ break;
-+ case MX29LV160T:
-+ case MX29LV320T:
-+ t = 3; /* Top boot */
-+ break;
-+ default:
-+ return;
-+ }
-+
-+ if (extp->TopBottom == t)
-+ /* boot location detected by the CFI layer is correct */
-+ return;
-+
-+ extp->TopBottom = t;
-+ printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
-+ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
-+}
-+#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
-+
- static struct cfi_fixup cfi_fixup_table[] = {
- { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri },
- #ifdef AMD_BOOTLOC_BUG
-@@ -400,6 +441,9 @@ static struct cfi_fixup fixup_table[] =
- */
- { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip },
- { CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock },
-+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+ { CFI_MFR_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc },
-+#endif
- { 0, 0, NULL }
- };
-
---- a/drivers/mtd/chips/Kconfig
-+++ b/drivers/mtd/chips/Kconfig
-@@ -189,6 +189,14 @@ config MTD_CFI_AMDSTD
- provides support for one of those command sets, used on chips
- including the AMD Am29LV320.
-
-+config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
-+ bool "Fix boot-block location for Macronix flash chips"
-+ depends on MTD_CFI_AMDSTD
-+ help
-+ Some Macronix flash chips have no/wrong boot-block location in the
-+ CFI table, and the driver may detect the type incorrectly. Select
-+ this if your board has such chip.
-+
- config MTD_CFI_STAA
- tristate "Support for ST (Advanced Architecture) flash chips"
- depends on MTD_GEN_PROBE
diff --git a/target/linux/adm5120/patches-3.7/102-jedec_pmc_39lvxxx_chips.patch b/target/linux/adm5120/patches-3.7/102-jedec_pmc_39lvxxx_chips.patch
deleted file mode 100644
index 00148fa..0000000
--- a/target/linux/adm5120/patches-3.7/102-jedec_pmc_39lvxxx_chips.patch
+++ /dev/null
@@ -1,68 +0,0 @@
---- a/drivers/mtd/chips/jedec_probe.c
-+++ b/drivers/mtd/chips/jedec_probe.c
-@@ -115,6 +115,10 @@
- #define UPD29F064115 0x221C
-
- /* PMC */
-+#define PM39LV512 0x001B
-+#define PM39LV010 0x001C
-+#define PM39LV020 0x003D
-+#define PM39LV040 0x003E
- #define PM49FL002 0x006D
- #define PM49FL004 0x006E
- #define PM49FL008 0x006A
-@@ -1259,6 +1263,54 @@ static const struct amd_flash_info jedec
- ERASEINFO(0x02000,2),
- ERASEINFO(0x04000,1),
- }
-+ }, {
-+ .mfr_id = CFI_MFR_PMC,
-+ .dev_id = PM39LV512,
-+ .name = "PMC Pm39LV512",
-+ .devtypes = CFI_DEVICETYPE_X8,
-+ .uaddr = MTD_UADDR_0x0555_0x02AA,
-+ .dev_size = SIZE_64KiB,
-+ .cmd_set = P_ID_AMD_STD,
-+ .nr_regions = 1,
-+ .regions = {
-+ ERASEINFO(0x01000,16),
-+ }
-+ }, {
-+ .mfr_id = CFI_MFR_PMC,
-+ .dev_id = PM39LV010,
-+ .name = "PMC Pm39LV010",
-+ .devtypes = CFI_DEVICETYPE_X8,
-+ .uaddr = MTD_UADDR_0x0555_0x02AA,
-+ .dev_size = SIZE_128KiB,
-+ .cmd_set = P_ID_AMD_STD,
-+ .nr_regions = 1,
-+ .regions = {
-+ ERASEINFO(0x01000,32),
-+ }
-+ }, {
-+ .mfr_id = CFI_MFR_PMC,
-+ .dev_id = PM39LV020,
-+ .name = "PMC Pm39LV020",
-+ .devtypes = CFI_DEVICETYPE_X8,
-+ .uaddr = MTD_UADDR_0x0555_0x02AA,
-+ .dev_size = SIZE_256KiB,
-+ .cmd_set = P_ID_AMD_STD,
-+ .nr_regions = 1,
-+ .regions = {
-+ ERASEINFO(0x01000,64),
-+ }
-+ }, {
-+ .mfr_id = CFI_MFR_PMC,
-+ .dev_id = PM39LV040,
-+ .name = "PMC Pm39LV040",
-+ .devtypes = CFI_DEVICETYPE_X8,
-+ .uaddr = MTD_UADDR_0x0555_0x02AA,
-+ .dev_size = SIZE_512KiB,
-+ .cmd_set = P_ID_AMD_STD,
-+ .nr_regions = 1,
-+ .regions = {
-+ ERASEINFO(0x01000,128),
-+ }
- }, {
- .mfr_id = CFI_MFR_PMC,
- .dev_id = PM49FL002,
diff --git a/target/linux/adm5120/patches-3.7/103-mtd_trxsplit.patch b/target/linux/adm5120/patches-3.7/103-mtd_trxsplit.patch
deleted file mode 100644
index 08fecd8..0000000
--- a/target/linux/adm5120/patches-3.7/103-mtd_trxsplit.patch
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/drivers/mtd/Kconfig
-+++ b/drivers/mtd/Kconfig
-@@ -31,6 +31,10 @@ config MTD_ROOTFS_SPLIT
- bool "Automatically split 'rootfs' partition for squashfs"
- default y
-
-+config MTD_TRXSPLIT
-+ bool "Automatically find and split TRX partitions"
-+ default n
-+
- config MTD_REDBOOT_PARTS
- tristate "RedBoot partition table parsing"
- ---help---
---- a/drivers/mtd/Makefile
-+++ b/drivers/mtd/Makefile
-@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_AR7_PARTS) += ar7part.o
- obj-$(CONFIG_MTD_BCM63XX_PARTS) += bcm63xxpart.o
- obj-$(CONFIG_MTD_BCM47XX_PARTS) += bcm47xxpart.o
- obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
-+obj-$(CONFIG_MTD_TRXSPLIT) += trxsplit.o
-
- # 'Users' - code which presents functionality to userspace.
- obj-$(CONFIG_MTD_CHAR) += mtdchar.o
diff --git a/target/linux/adm5120/patches-3.7/120-rb153_cf_driver.patch b/target/linux/adm5120/patches-3.7/120-rb153_cf_driver.patch
deleted file mode 100644
index 3374554..0000000
--- a/target/linux/adm5120/patches-3.7/120-rb153_cf_driver.patch
+++ /dev/null
@@ -1,28 +0,0 @@
---- a/drivers/ata/Makefile
-+++ b/drivers/ata/Makefile
-@@ -90,6 +90,7 @@ obj-$(CONFIG_PATA_PCMCIA) += pata_pcmcia
- obj-$(CONFIG_PATA_PALMLD) += pata_palmld.o
- obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
- obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
-+obj-$(CONFIG_PATA_RB153_CF) += pata_rb153_cf.o
- obj-$(CONFIG_PATA_RB532) += pata_rb532_cf.o
- obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o
- obj-$(CONFIG_PATA_SAMSUNG_CF) += pata_samsung_cf.o
---- a/drivers/ata/Kconfig
-+++ b/drivers/ata/Kconfig
-@@ -852,6 +852,15 @@ config PATA_QDI
- help
- Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
-
-+config PATA_RB153_CF
-+ tristate "RouterBOARD 153 Compact Flash support"
-+ depends on ADM5120_MACH_RB_153
-+ help
-+ This option enables support for a Compact Flash connected on
-+ the RouterBOARD 153.
-+
-+ If unsure, say N.
-+
- config PATA_RB532
- tristate "RouterBoard 532 PATA CompactFlash support"
- depends on MIKROTIK_RB532
diff --git a/target/linux/adm5120/patches-3.7/200-amba_pl010_hacks.patch b/target/linux/adm5120/patches-3.7/200-amba_pl010_hacks.patch
deleted file mode 100644
index 7f319d8..0000000
--- a/target/linux/adm5120/patches-3.7/200-amba_pl010_hacks.patch
+++ /dev/null
@@ -1,355 +0,0 @@
---- a/drivers/tty/serial/amba-pl010.c
-+++ b/drivers/tty/serial/amba-pl010.c
-@@ -49,11 +49,9 @@
-
- #include <asm/io.h>
-
--#define UART_NR 8
--
- #define SERIAL_AMBA_MAJOR 204
- #define SERIAL_AMBA_MINOR 16
--#define SERIAL_AMBA_NR UART_NR
-+#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS
-
- #define AMBA_ISR_PASS_LIMIT 256
-
-@@ -79,9 +77,9 @@ static void pl010_stop_tx(struct uart_po
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = __raw_readl(uap->port.membase + UART010_CR);
- cr &= ~UART010_CR_TIE;
-- writel(cr, uap->port.membase + UART010_CR);
-+ __raw_writel(cr, uap->port.membase + UART010_CR);
- }
-
- static void pl010_start_tx(struct uart_port *port)
-@@ -89,9 +87,9 @@ static void pl010_start_tx(struct uart_p
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = __raw_readl(uap->port.membase + UART010_CR);
- cr |= UART010_CR_TIE;
-- writel(cr, uap->port.membase + UART010_CR);
-+ __raw_writel(cr, uap->port.membase + UART010_CR);
- }
-
- static void pl010_stop_rx(struct uart_port *port)
-@@ -99,9 +97,9 @@ static void pl010_stop_rx(struct uart_po
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = __raw_readl(uap->port.membase + UART010_CR);
- cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
-- writel(cr, uap->port.membase + UART010_CR);
-+ __raw_writel(cr, uap->port.membase + UART010_CR);
- }
-
- static void pl010_enable_ms(struct uart_port *port)
-@@ -109,9 +107,9 @@ static void pl010_enable_ms(struct uart_
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
- unsigned int cr;
-
-- cr = readb(uap->port.membase + UART010_CR);
-+ cr = __raw_readl(uap->port.membase + UART010_CR);
- cr |= UART010_CR_MSIE;
-- writel(cr, uap->port.membase + UART010_CR);
-+ __raw_writel(cr, uap->port.membase + UART010_CR);
- }
-
- static void pl010_rx_chars(struct uart_amba_port *uap)
-@@ -119,9 +117,9 @@ static void pl010_rx_chars(struct uart_a
- struct tty_struct *tty = uap->port.state->port.tty;
- unsigned int status, ch, flag, rsr, max_count = 256;
-
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = __raw_readl(uap->port.membase + UART01x_FR);
- while (UART_RX_DATA(status) && max_count--) {
-- ch = readb(uap->port.membase + UART01x_DR);
-+ ch = __raw_readl(uap->port.membase + UART01x_DR);
- flag = TTY_NORMAL;
-
- uap->port.icount.rx++;
-@@ -130,9 +128,9 @@ static void pl010_rx_chars(struct uart_a
- * Note that the error handling code is
- * out of the main execution path
- */
-- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
-+ rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
- if (unlikely(rsr & UART01x_RSR_ANY)) {
-- writel(0, uap->port.membase + UART01x_ECR);
-+ __raw_writel(0, uap->port.membase + UART01x_ECR);
-
- if (rsr & UART01x_RSR_BE) {
- rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
-@@ -162,7 +160,7 @@ static void pl010_rx_chars(struct uart_a
- uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
-
- ignore_char:
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = __raw_readl(uap->port.membase + UART01x_FR);
- }
- spin_unlock(&uap->port.lock);
- tty_flip_buffer_push(tty);
-@@ -175,7 +173,7 @@ static void pl010_tx_chars(struct uart_a
- int count;
-
- if (uap->port.x_char) {
-- writel(uap->port.x_char, uap->port.membase + UART01x_DR);
-+ __raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR);
- uap->port.icount.tx++;
- uap->port.x_char = 0;
- return;
-@@ -187,7 +185,7 @@ static void pl010_tx_chars(struct uart_a
-
- count = uap->port.fifosize >> 1;
- do {
-- writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
-+ __raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
- xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- uap->port.icount.tx++;
- if (uart_circ_empty(xmit))
-@@ -205,9 +203,9 @@ static void pl010_modem_status(struct ua
- {
- unsigned int status, delta;
-
-- writel(0, uap->port.membase + UART010_ICR);
-+ __raw_writel(0, uap->port.membase + UART010_ICR);
-
-- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+ status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-
- delta = status ^ uap->old_status;
- uap->old_status = status;
-@@ -235,7 +233,7 @@ static irqreturn_t pl010_int(int irq, vo
-
- spin_lock(&uap->port.lock);
-
-- status = readb(uap->port.membase + UART010_IIR);
-+ status = __raw_readl(uap->port.membase + UART010_IIR);
- if (status) {
- do {
- if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
-@@ -248,7 +246,7 @@ static irqreturn_t pl010_int(int irq, vo
- if (pass_counter-- == 0)
- break;
-
-- status = readb(uap->port.membase + UART010_IIR);
-+ status = __raw_readl(uap->port.membase + UART010_IIR);
- } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
- UART010_IIR_TIS));
- handled = 1;
-@@ -262,7 +260,7 @@ static irqreturn_t pl010_int(int irq, vo
- static unsigned int pl010_tx_empty(struct uart_port *port)
- {
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
-- unsigned int status = readb(uap->port.membase + UART01x_FR);
-+ unsigned int status = __raw_readl(uap->port.membase + UART01x_FR);
- return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
- }
-
-@@ -272,7 +270,7 @@ static unsigned int pl010_get_mctrl(stru
- unsigned int result = 0;
- unsigned int status;
-
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = __raw_readl(uap->port.membase + UART01x_FR);
- if (status & UART01x_FR_DCD)
- result |= TIOCM_CAR;
- if (status & UART01x_FR_DSR)
-@@ -298,12 +296,12 @@ static void pl010_break_ctl(struct uart_
- unsigned int lcr_h;
-
- spin_lock_irqsave(&uap->port.lock, flags);
-- lcr_h = readb(uap->port.membase + UART010_LCRH);
-+ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
- if (break_state == -1)
- lcr_h |= UART01x_LCRH_BRK;
- else
- lcr_h &= ~UART01x_LCRH_BRK;
-- writel(lcr_h, uap->port.membase + UART010_LCRH);
-+ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
- spin_unlock_irqrestore(&uap->port.lock, flags);
- }
-
-@@ -331,12 +329,12 @@ static int pl010_startup(struct uart_por
- /*
- * initialise the old status of the modem signals
- */
-- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-+ uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
-
- /*
- * Finally, enable interrupts
- */
-- writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
-+ __raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
- uap->port.membase + UART010_CR);
-
- return 0;
-@@ -359,10 +357,10 @@ static void pl010_shutdown(struct uart_p
- /*
- * disable all interrupts, disable the port
- */
-- writel(0, uap->port.membase + UART010_CR);
-+ __raw_writel(0, uap->port.membase + UART010_CR);
-
- /* disable break condition and fifos */
-- writel(readb(uap->port.membase + UART010_LCRH) &
-+ __raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) &
- ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
- uap->port.membase + UART010_LCRH);
-
-@@ -384,7 +382,7 @@ pl010_set_termios(struct uart_port *port
- /*
- * Ask the core to calculate the divisor for us.
- */
-- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
-+ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
- quot = uart_get_divisor(port, baud);
-
- switch (termios->c_cflag & CSIZE) {
-@@ -447,25 +445,25 @@ pl010_set_termios(struct uart_port *port
- uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
-
- /* first, disable everything */
-- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
-+ old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
-
- if (UART_ENABLE_MS(port, termios->c_cflag))
- old_cr |= UART010_CR_MSIE;
-
-- writel(0, uap->port.membase + UART010_CR);
-+ __raw_writel(0, uap->port.membase + UART010_CR);
-
- /* Set baud rate */
- quot -= 1;
-- writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
-- writel(quot & 0xff, uap->port.membase + UART010_LCRL);
-+ __raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
-+ __raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL);
-
- /*
- * ----------v----------v----------v----------v-----
- * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
- * ----------^----------^----------^----------^-----
- */
-- writel(lcr_h, uap->port.membase + UART010_LCRH);
-- writel(old_cr, uap->port.membase + UART010_CR);
-+ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
-+ __raw_writel(old_cr, uap->port.membase + UART010_CR);
-
- spin_unlock_irqrestore(&uap->port.lock, flags);
- }
-@@ -547,7 +545,7 @@ static struct uart_ops amba_pl010_pops =
- .verify_port = pl010_verify_port,
- };
-
--static struct uart_amba_port *amba_ports[UART_NR];
-+static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
-
- #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
-
-@@ -557,10 +555,10 @@ static void pl010_console_putchar(struct
- unsigned int status;
-
- do {
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = __raw_readl(uap->port.membase + UART01x_FR);
- barrier();
- } while (!UART_TX_READY(status));
-- writel(ch, uap->port.membase + UART01x_DR);
-+ __raw_writel(ch, uap->port.membase + UART01x_DR);
- }
-
- static void
-@@ -574,8 +572,8 @@ pl010_console_write(struct console *co,
- /*
- * First save the CR then disable the interrupts
- */
-- old_cr = readb(uap->port.membase + UART010_CR);
-- writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
-+ old_cr = __raw_readl(uap->port.membase + UART010_CR);
-+ __raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
-
- uart_console_write(&uap->port, s, count, pl010_console_putchar);
-
-@@ -584,10 +582,10 @@ pl010_console_write(struct console *co,
- * and restore the TCR
- */
- do {
-- status = readb(uap->port.membase + UART01x_FR);
-+ status = __raw_readl(uap->port.membase + UART01x_FR);
- barrier();
- } while (status & UART01x_FR_BUSY);
-- writel(old_cr, uap->port.membase + UART010_CR);
-+ __raw_writel(old_cr, uap->port.membase + UART010_CR);
-
- clk_disable(uap->clk);
- }
-@@ -596,9 +594,9 @@ static void __init
- pl010_console_get_options(struct uart_amba_port *uap, int *baud,
- int *parity, int *bits)
- {
-- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
-+ if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
- unsigned int lcr_h, quot;
-- lcr_h = readb(uap->port.membase + UART010_LCRH);
-+ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
-
- *parity = 'n';
- if (lcr_h & UART01x_LCRH_PEN) {
-@@ -613,8 +611,8 @@ pl010_console_get_options(struct uart_am
- else
- *bits = 8;
-
-- quot = readb(uap->port.membase + UART010_LCRL) |
-- readb(uap->port.membase + UART010_LCRM) << 8;
-+ quot = __raw_readl(uap->port.membase + UART010_LCRL) |
-+ __raw_readl(uap->port.membase + UART010_LCRM) << 8;
- *baud = uap->port.uartclk / (16 * (quot + 1));
- }
- }
-@@ -633,7 +631,7 @@ static int __init pl010_console_setup(st
- * if so, search for the first available port that does have
- * console support.
- */
-- if (co->index >= UART_NR)
-+ if (co->index >= SERIAL_AMBA_NR)
- co->index = 0;
- uap = amba_ports[co->index];
- if (!uap)
-@@ -675,7 +673,7 @@ static struct uart_driver amba_reg = {
- .dev_name = "ttyAM",
- .major = SERIAL_AMBA_MAJOR,
- .minor = SERIAL_AMBA_MINOR,
-- .nr = UART_NR,
-+ .nr = SERIAL_AMBA_NR,
- .cons = AMBA_CONSOLE,
- };
-
---- a/drivers/tty/serial/Kconfig
-+++ b/drivers/tty/serial/Kconfig
-@@ -16,10 +16,18 @@ config SERIAL_AMBA_PL010
- help
- This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
- an Integrator/AP or Integrator/PP2 platform, or if you have a
-- Cirrus Logic EP93xx CPU, say Y or M here.
-+ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
-
- If unsure, say N.
-
-+config SERIAL_AMBA_PL010_NUMPORTS
-+ int "Maximum number of AMBA PL010 serial ports"
-+ depends on SERIAL_AMBA_PL010
-+ default "8"
-+ ---help---
-+ Set this to the number of serial ports you want the AMBA PL010 driver
-+ to support.
-+
- config SERIAL_AMBA_PL010_CONSOLE
- bool "Support for console on AMBA serial port"
- depends on SERIAL_AMBA_PL010=y
diff --git a/target/linux/adm5120/patches-3.7/203-gpio_leds_brightness.patch b/target/linux/adm5120/patches-3.7/203-gpio_leds_brightness.patch
deleted file mode 100644
index 5345022..0000000
--- a/target/linux/adm5120/patches-3.7/203-gpio_leds_brightness.patch
+++ /dev/null
@@ -1,27 +0,0 @@
---- a/drivers/leds/leds-gpio.c
-+++ b/drivers/leds/leds-gpio.c
-@@ -55,13 +55,17 @@ static void gpio_led_set(struct led_clas
- container_of(led_cdev, struct gpio_led_data, cdev);
- int level;
-
-- if (value == LED_OFF)
-- level = 0;
-- else
-- level = 1;
--
-- if (led_dat->active_low)
-- level = !level;
-+ switch (value) {
-+ case LED_OFF:
-+ level = led_dat->active_low ? 1 : 0;
-+ break;
-+ case LED_FULL:
-+ level = led_dat->active_low ? 0 : 1;
-+ break;
-+ default:
-+ level = value;
-+ break;
-+ }
-
- /* Setting GPIOs with I2C/etc requires a task context, and we don't
- * seem to have a reliable way to know if we're already in one; so
diff --git a/target/linux/adm5120/patches-3.7/310-adm5120_wdt.patch b/target/linux/adm5120/patches-3.7/310-adm5120_wdt.patch
deleted file mode 100644
index d55f63c..0000000
--- a/target/linux/adm5120/patches-3.7/310-adm5120_wdt.patch
+++ /dev/null
@@ -1,31 +0,0 @@
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -972,6 +972,18 @@ config RC32434_WDT
- To compile this driver as a module, choose M here: the
- module will be called rc32434_wdt.
-
-+config ADM5120_WDT
-+ tristate "Infineon ADM5120 SoC hardware watchdog"
-+ depends on WATCHDOG && ADM5120
-+ help
-+ This is a driver for hardware watchdog integrated in Infineon
-+ ADM5120 SoC. This watchdog simply watches your kernel to make sure
-+ it doesn't freeze, and if it does, it reboots your computer after a
-+ certain amount of time.
-+
-+ To compile this driver as a module, choose M here: the module will be
-+ called adm5120_wdt.
-+
- config INDYDOG
- tristate "Indy/I2 Hardware Watchdog"
- depends on SGI_HAS_INDYDOG
---- a/drivers/watchdog/Makefile
-+++ b/drivers/watchdog/Makefile
-@@ -122,6 +122,7 @@ obj-$(CONFIG_ATH79_WDT) += ath79_wdt.o
- obj-$(CONFIG_BCM47XX_WDT) += bcm47xx_wdt.o
- obj-$(CONFIG_BCM63XX_WDT) += bcm63xx_wdt.o
- obj-$(CONFIG_RC32434_WDT) += rc32434_wdt.o
-+obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o
- obj-$(CONFIG_INDYDOG) += indydog.o
- obj-$(CONFIG_JZ4740_WDT) += jz4740_wdt.o
- obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o