diff options
Diffstat (limited to 'target/linux/ar71xx')
9 files changed, 217 insertions, 1 deletions
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds index 1db6ad0..39f472a 100644 --- a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds +++ b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds @@ -43,6 +43,11 @@ antminer-s3) ucidef_set_led_default "lan" "LAN" "antminer-s3:yellow:lan" "0" ;; +arduino-yun) + ucidef_set_led_wlan "wlan" "WLAN" "arduino:blue:wlan" "phy0tpt" + ucidef_set_led_usbdev "usb" "USB" "arduino:white:usb" "1-1.1" + ;; + ap113) ucidef_set_led_usbdev "usb" "USB" "ap113:green:usb" "1-1" ;; diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network index 2cba155..2765adb 100644 --- a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network +++ b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network @@ -388,6 +388,7 @@ wp543) ucidef_set_interface_lan "eth0" ;; +arduino-yun | \ dir-505-a1) ucidef_set_interface_lan "eth1" ;; diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 8f3bf1d..0e92ee7 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -359,6 +359,9 @@ ar71xx_board_detect() { *Antminer-S3) name="antminer-s3" ;; + *"Arduino Yun") + name="arduino-yun" + ;; *AP113) name="ap113" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 7863093..b97c076 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -173,6 +173,7 @@ platform_check_image() { ;; alfa-ap96 | \ alfa-nx | \ + arduino-yun | \ ap113 | \ ap121 | \ ap121-mini | \ diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1 index b877514..08e252d 100644 --- a/target/linux/ar71xx/config-4.1 +++ b/target/linux/ar71xx/config-4.1 @@ -46,6 +46,7 @@ CONFIG_ATH79_MACH_AP81=y CONFIG_ATH79_MACH_AP83=y CONFIG_ATH79_MACH_AP96=y CONFIG_ATH79_MACH_ARCHER_C7=y +CONFIG_ATH79_MACH_ARDUINO_YUN=y CONFIG_ATH79_MACH_AW_NR580=y CONFIG_ATH79_MACH_BHU_BXU2000N2_A=y CONFIG_ATH79_MACH_BSB=y @@ -193,6 +194,8 @@ CONFIG_CPU_R4K_FPU=y CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_CPU_SUPPORTS_MSA=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y CONFIG_CSRC_R4K=y CONFIG_DMA_NONCOHERENT=y CONFIG_EARLY_PRINTK=y @@ -334,7 +337,7 @@ CONFIG_SOC_AR933X=y CONFIG_SOC_AR934X=y CONFIG_SOC_QCA953X=y CONFIG_SOC_QCA955X=y -# CONFIG_SOC_QCA956X is not set +CONFIG_SOC_QCA956X=y CONFIG_SPI=y CONFIG_SPI_AP83=y CONFIG_SPI_ATH79=y diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-arduino-yun.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-arduino-yun.c new file mode 100644 index 0000000..fbe1f99 --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-arduino-yun.c @@ -0,0 +1,137 @@ +/* + * Arduino Yun support + * + * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org> + * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-m25p80.h" +#include "dev-spi.h" +#include "dev-usb.h" +#include "dev-wmac.h" +#include "machtypes.h" +#include <asm/mach-ath79/ar71xx_regs.h> +#include <asm/mach-ath79/ath79.h> +#include "common.h" +#include "gpio.h" +#include "linux/gpio.h" + +// Uncomment to have reset on gpio18 instead of gipo7 +#define DS2_B + +#define DS_GPIO_LED_WLAN 0 +#define DS_GPIO_LED_USB 1 + +#define DS_GPIO_OE 21 +#define DS_GPIO_AVR_RESET 18 + +// Maintained to have the console in the previous version of DS2 working +#define DS_GPIO_AVR_RESET_DS2 7 + +#define DS_GPIO_OE2 22 +#define DS_GPIO_UART_ENA 23 +#define DS_GPIO_CONF_BTN 20 + +#define DS_KEYS_POLL_INTERVAL 20 /* msecs */ +#define DS_KEYS_DEBOUNCE_INTERVAL (3 * DS_KEYS_POLL_INTERVAL) + +#define DS_MAC0_OFFSET 0x0000 +#define DS_MAC1_OFFSET 0x0006 +#define DS_CALDATA_OFFSET 0x1000 +#define DS_WMAC_MAC_OFFSET 0x1002 + + +static struct gpio_led ds_leds_gpio[] __initdata = { + { + .name = "arduino:white:usb", + .gpio = DS_GPIO_LED_USB, + .active_low = 0, + }, + { + .name = "arduino:blue:wlan", + .gpio = DS_GPIO_LED_WLAN, + .active_low = 0, + }, +}; + +static void __init ds_common_setup(void) +{ + static u8 mac[6]; + + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + ath79_register_m25p80(NULL); + + if (ar93xx_wmac_read_mac_address(mac)) { + ath79_register_wmac(NULL, NULL); + } else { + ath79_register_wmac(art + DS_CALDATA_OFFSET, + art + DS_WMAC_MAC_OFFSET); + memcpy(mac, art + DS_WMAC_MAC_OFFSET, sizeof(mac)); + } + + mac[3] |= 0x08; + ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0); + + mac[3] &= 0xF7; + ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0); + ath79_register_mdio(0, 0x0); + + /* LAN ports */ + ath79_register_eth(1); + + /* WAN port */ + ath79_register_eth(0); +} + +static void __init ds_setup(void) +{ + u32 t; + + ds_common_setup(); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(ds_leds_gpio), + ds_leds_gpio); + ath79_register_usb(); + + //Disable the Function for some pins to have GPIO functionality active + // GPIO6-7-8 and GPIO11 + ath79_gpio_function_setup(AR933X_GPIO_FUNC_JTAG_DISABLE | AR933X_GPIO_FUNC_I2S_MCK_EN, 0); + + ath79_gpio_function2_setup(AR933X_GPIO_FUNC2_JUMPSTART_DISABLE, 0); + + printk("Setting DogStick2 GPIO\n"); + + t = ath79_reset_rr(AR933X_RESET_REG_BOOTSTRAP); + t |= AR933X_BOOTSTRAP_MDIO_GPIO_EN; + ath79_reset_wr(AR933X_RESET_REG_BOOTSTRAP, t); + + // Put the avr reset to high + if (gpio_request_one(DS_GPIO_AVR_RESET_DS2, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, "OE-1") != 0) + printk("Error setting GPIO OE\n"); + gpio_unexport(DS_GPIO_AVR_RESET_DS2); + gpio_free(DS_GPIO_AVR_RESET_DS2); + + // enable OE of level shifter + if (gpio_request_one(DS_GPIO_OE, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, "OE-1") != 0) + printk("Error setting GPIO OE\n"); + + if (gpio_request_one(DS_GPIO_UART_ENA, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, "UART-ENA") != 0) + printk("Error setting GPIO Uart Enable\n"); + + // enable OE of level shifter + if (gpio_request_one(DS_GPIO_OE2, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, "OE-2") != 0) + printk("Error setting GPIO OE2\n"); +} + +MIPS_MACHINE(ATH79_MACH_ARDUINO_YUN, "Yun", "Arduino Yun", ds_setup); diff --git a/target/linux/ar71xx/generic/profiles/arduino.mk b/target/linux/ar71xx/generic/profiles/arduino.mk new file mode 100644 index 0000000..8ae5054 --- /dev/null +++ b/target/linux/ar71xx/generic/profiles/arduino.mk @@ -0,0 +1,19 @@ +# +# Copyright (C) 2009-2010 OpenWrt.org +# +# This is free software, licensed under the GNU General Public License v2. +# See /LICENSE for more information. +# + +define Profile/Yun + NAME:=Arduino Yun based on Atheros AR9331 + PACKAGES:=kmod-usb-core kmod-usb2 +endef + +define Profile/Yun/Description + Package set optimized for the Arduino Yun. + This is sometimes also named Genuino Yun or Linino Yun. +endef + +$(eval $(call Profile,Yun)) + diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile index 11cf716..0484f07 100644 --- a/target/linux/ar71xx/image/Makefile +++ b/target/linux/ar71xx/image/Makefile @@ -1489,6 +1489,8 @@ mynet_n600_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdat mynet_rext_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,7808k(firmware),64k(nvram)ro,64k(ART)ro zyx_nbg6716_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(env)ro,64k(RFdata)ro,-(nbu);ar934x-nfc:2048k(zyxel_rfsd),2048k(romd),1024k(header),2048k(kernel),-(ubi) qihoo_c301_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(devdata),64k(devconf),15744k(firmware),64k(warm_start),64k(action_image_config),64k(radiocfg)ro;spi0.1:15360k(upgrade2),1024k(privatedata) +yun_mtdlayout_8M=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6464k(rootfs),1280k(kernel),64k(nvram),64k(art),7744k@0x50000(firmware) +yun_mtdlayout_16M=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14656k(rootfs),1280k(kernel),64k(nvram),64k(art),15936k@0x50000(firmware) define Image/BuildKernel @@ -2249,6 +2251,8 @@ $(eval $(call SingleProfile,AthLzma,64k,WLR8100,wlr8100,WLR8100,ttyS0,115200,$$( $(eval $(call SingleProfile,AthLzma,64k,WPJ344_16M,wpj344-16M,WPJ344,ttyS0,115200,$$(wpj344_mtdlayout_16M),KRuImage,65536)) $(eval $(call SingleProfile,AthLzma,64k,WPJ531_16M,wpj531-16M,WPJ531,ttyS0,115200,$$(wpj531_mtdlayout_16M),KRuImage,65536)) $(eval $(call SingleProfile,AthLzma,64k,WPJ558_16M,wpj558-16M,WPJ558,ttyS0,115200,$$(wpj558_mtdlayout_16M),KRuImage,65536)) +$(eval $(call SingleProfile,AthLzma,64k,YUN_8M,yun-8M,Yun,ttyATH0,250000,$$(yun_mtdlayout_8M),RKuImage)) +$(eval $(call SingleProfile,AthLzma,64k,YUN_16M,yun-16M,Yun,ttyATH0,250000,$$(yun_mtdlayout_16M),RKuImage)) $(eval $(call SingleProfile,Belkin,64k,F9K1115V2,f9k1115v2,F9K1115V2,ttyS0,115200,$$(f9k1115v2_mtdlayout),BR-6679BAC)) @@ -2375,6 +2379,7 @@ $(eval $(call MultiProfile,WPE72,WPE72_4M WPE72_8M WPE72_16M)) $(eval $(call MultiProfile,WPJ344,WPJ344_16M)) $(eval $(call MultiProfile,WPJ531,WPJ531_16M)) $(eval $(call MultiProfile,WPJ558,WPJ558_16M)) +$(eval $(call MultiProfile,Yun,YUN_16M YUN_8M)) $(eval $(call MultiProfile,Minimal,$(SINGLE_PROFILES))) $(eval $(call MultiProfile,Madwifi,EAP7660D WP543)) diff --git a/target/linux/ar71xx/patches-4.1/822-MIPS-ath79-Arduino-yun-support.patch b/target/linux/ar71xx/patches-4.1/822-MIPS-ath79-Arduino-yun-support.patch new file mode 100644 index 0000000..7007310 --- /dev/null +++ b/target/linux/ar71xx/patches-4.1/822-MIPS-ath79-Arduino-yun-support.patch @@ -0,0 +1,42 @@ +--- a/arch/mips/ath79/Kconfig ++++ b/arch/mips/ath79/Kconfig +@@ -76,6 +76,19 @@ config ATH79_MACH_ANTMINER_S3 + select ATH79_DEV_USB + select ATH79_DEV_WMAC + ++config ATH79_MACH_ARDUINO_YUN ++ bool "Arduino Yun" ++ select SOC_AR933X ++ select ATH79_DEV_ETH ++ select ATH79_DEV_GPIO_BUTTONS ++ select ATH79_DEV_LEDS_GPIO ++ select ATH79_DEV_M25P80 ++ select ATH79_DEV_USB ++ select ATH79_DEV_WMAC ++ help ++ Say 'Y' here if you want your kernel to support the ++ Arduino Yun. ++ + config ATH79_MACH_AP113 + bool "Atheros AP113 board support" + select SOC_AR724X +--- a/arch/mips/ath79/machtypes.h ++++ b/arch/mips/ath79/machtypes.h +@@ -23,6 +23,7 @@ enum ath79_mach_type { + ATH79_MACH_ALL0315N, /* Allnet ALL0315N */ + ATH79_MACH_ANTMINER_S1, /* Antminer S1 */ + ATH79_MACH_ANTMINER_S3, /* Antminer S3 */ ++ ATH79_MACH_ARDUINO_YUN, /* Yun */ + ATH79_MACH_AP113, /* Atheros AP113 reference board */ + ATH79_MACH_AP121, /* Atheros AP121 reference board */ + ATH79_MACH_AP121_MINI, /* Atheros AP121-MINI reference board */ +--- a/arch/mips/ath79/Makefile ++++ b/arch/mips/ath79/Makefile +@@ -44,6 +44,7 @@ obj-$(CONFIG_ATH79_MACH_ALL0258N) += mac + obj-$(CONFIG_ATH79_MACH_ALL0315N) += mach-all0315n.o + obj-$(CONFIG_ATH79_MACH_ANTMINER_S1)+= mach-antminer-s1.o + obj-$(CONFIG_ATH79_MACH_ANTMINER_S3)+= mach-antminer-s3.o ++obj-$(CONFIG_ATH79_MACH_ARDUINO_YUN) += mach-arduino-yun.o + obj-$(CONFIG_ATH79_MACH_AP113) += mach-ap113.o + obj-$(CONFIG_ATH79_MACH_AP121) += mach-ap121.o + obj-$(CONFIG_ATH79_MACH_AP132) += mach-ap132.o |