diff options
Diffstat (limited to 'target/linux/brcm2708/patches-4.9/950-0173-drm-vc4-Add-DSI-driver.patch')
| -rw-r--r-- | target/linux/brcm2708/patches-4.9/950-0173-drm-vc4-Add-DSI-driver.patch | 1817 |
1 files changed, 1817 insertions, 0 deletions
diff --git a/target/linux/brcm2708/patches-4.9/950-0173-drm-vc4-Add-DSI-driver.patch b/target/linux/brcm2708/patches-4.9/950-0173-drm-vc4-Add-DSI-driver.patch new file mode 100644 index 0000000..97ae4a4 --- /dev/null +++ b/target/linux/brcm2708/patches-4.9/950-0173-drm-vc4-Add-DSI-driver.patch @@ -0,0 +1,1817 @@ +From 38ea3f3665eaa9deedc3588196fe9ba9bb4032ec Mon Sep 17 00:00:00 2001 +From: Eric Anholt <eric@anholt.net> +Date: Wed, 10 Feb 2016 11:42:32 -0800 +Subject: [PATCH] drm/vc4: Add DSI driver + +The DSI0 and DSI1 blocks on the 2835 are related hardware blocks. +Some registers move around, and the featureset is slightly different, +as DSI1 (the 4-lane DSI) is a later version of the hardware block. +This driver doesn't yet enable DSI0, since we don't have any hardware +to test against, but it does put a lot of the register definitions and +code in place. + +Signed-off-by: Eric Anholt <eric@anholt.net> +--- + drivers/gpu/drm/vc4/Kconfig | 2 + + drivers/gpu/drm/vc4/Makefile | 1 + + drivers/gpu/drm/vc4/vc4_debugfs.c | 1 + + drivers/gpu/drm/vc4/vc4_drv.c | 1 + + drivers/gpu/drm/vc4/vc4_drv.h | 5 + + drivers/gpu/drm/vc4/vc4_dsi.c | 1725 +++++++++++++++++++++++++++++++++++++ + 6 files changed, 1735 insertions(+) + create mode 100644 drivers/gpu/drm/vc4/vc4_dsi.c + +--- a/drivers/gpu/drm/vc4/Kconfig ++++ b/drivers/gpu/drm/vc4/Kconfig +@@ -2,10 +2,12 @@ config DRM_VC4 + tristate "Broadcom VC4 Graphics" + depends on ARCH_BCM2835 || COMPILE_TEST + depends on DRM ++ depends on COMMON_CLK + select DRM_KMS_HELPER + select DRM_KMS_CMA_HELPER + select DRM_GEM_CMA_HELPER + select DRM_PANEL ++ select DRM_MIPI_DSI + help + Choose this option if you have a system that has a Broadcom + VC4 GPU, such as the Raspberry Pi or other BCM2708/BCM2835. +--- a/drivers/gpu/drm/vc4/Makefile ++++ b/drivers/gpu/drm/vc4/Makefile +@@ -8,6 +8,7 @@ vc4-y := \ + vc4_crtc.o \ + vc4_drv.o \ + vc4_dpi.o \ ++ vc4_dsi.o \ + vc4_firmware_kms.o \ + vc4_kms.o \ + vc4_gem.o \ +--- a/drivers/gpu/drm/vc4/vc4_debugfs.c ++++ b/drivers/gpu/drm/vc4/vc4_debugfs.c +@@ -18,6 +18,7 @@ + static const struct drm_info_list vc4_debugfs_list[] = { + {"bo_stats", vc4_bo_stats_debugfs, 0}, + {"dpi_regs", vc4_dpi_debugfs_regs, 0}, ++ {"dsi1_regs", vc4_dsi_debugfs_regs, 0, (void *)(uintptr_t)1}, + {"hdmi_regs", vc4_hdmi_debugfs_regs, 0}, + {"vec_regs", vc4_vec_debugfs_regs, 0}, + {"hvs_regs", vc4_hvs_debugfs_regs, 0}, +--- a/drivers/gpu/drm/vc4/vc4_drv.c ++++ b/drivers/gpu/drm/vc4/vc4_drv.c +@@ -296,6 +296,7 @@ static struct platform_driver *const com + &vc4_hdmi_driver, + &vc4_vec_driver, + &vc4_dpi_driver, ++ &vc4_dsi_driver, + &vc4_hvs_driver, + &vc4_crtc_driver, + &vc4_firmware_kms_driver, +--- a/drivers/gpu/drm/vc4/vc4_drv.h ++++ b/drivers/gpu/drm/vc4/vc4_drv.h +@@ -20,6 +20,7 @@ struct vc4_dev { + struct vc4_crtc *crtc[3]; + struct vc4_v3d *v3d; + struct vc4_dpi *dpi; ++ struct vc4_dsi *dsi1; + struct vc4_vec *vec; + + struct drm_fbdev_cma *fbdev; +@@ -468,6 +469,10 @@ void __iomem *vc4_ioremap_regs(struct pl + extern struct platform_driver vc4_dpi_driver; + int vc4_dpi_debugfs_regs(struct seq_file *m, void *unused); + ++/* vc4_dsi.c */ ++extern struct platform_driver vc4_dsi_driver; ++int vc4_dsi_debugfs_regs(struct seq_file *m, void *unused); ++ + /* vc4_firmware_kms.c */ + extern struct platform_driver vc4_firmware_kms_driver; + void vc4_fkms_cancel_page_flip(struct drm_crtc *crtc, struct drm_file *file); +--- /dev/null ++++ b/drivers/gpu/drm/vc4/vc4_dsi.c +@@ -0,0 +1,1725 @@ ++/* ++ * Copyright (C) 2016 Broadcom ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published by ++ * the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but WITHOUT ++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or ++ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for ++ * more details. ++ * ++ * You should have received a copy of the GNU General Public License along with ++ * this program. If not, see <http://www.gnu.org/licenses/>. ++ */ ++ ++/** ++ * DOC: VC4 DSI0/DSI1 module ++ * ++ * BCM2835 contains two DSI modules, DSI0 and DSI1. DSI0 is a ++ * single-lane DSI controller, while DSI1 is a more modern 4-lane DSI ++ * controller. ++ * ++ * Most Raspberry Pi boards expose DSI1 as their "DISPLAY" connector, ++ * while the compute module brings both DSI0 and DSI1 out. ++ * ++ * This driver has been tested for DSI1 video-mode display only ++ * currently, with most of the information necessary for DSI0 ++ * hopefully present. ++ */ ++ ++#include "drm_atomic_helper.h" ++#include "drm_crtc_helper.h" ++#include "drm_edid.h" ++#include "drm_mipi_dsi.h" ++#include "drm_panel.h" ++#include "linux/clk.h" ++#include "linux/clk-provider.h" ++#include "linux/completion.h" ++#include "linux/component.h" ++#include "linux/dmaengine.h" ++#include "linux/i2c.h" ++#include "linux/of_address.h" ++#include "linux/of_platform.h" ++#include "linux/pm_runtime.h" ++#include "vc4_drv.h" ++#include "vc4_regs.h" ++ ++#define DSI_CMD_FIFO_DEPTH 16 ++#define DSI_PIX_FIFO_DEPTH 256 ++#define DSI_PIX_FIFO_WIDTH 4 ++ ++#define DSI0_CTRL 0x00 ++ ++/* Command packet control. */ ++#define DSI0_TXPKT1C 0x04 /* AKA PKTC */ ++#define DSI1_TXPKT1C 0x04 ++# define DSI_TXPKT1C_TRIG_CMD_MASK VC4_MASK(31, 24) ++# define DSI_TXPKT1C_TRIG_CMD_SHIFT 24 ++# define DSI_TXPKT1C_CMD_REPEAT_MASK VC4_MASK(23, 10) ++# define DSI_TXPKT1C_CMD_REPEAT_SHIFT 10 ++ ++# define DSI_TXPKT1C_DISPLAY_NO_MASK VC4_MASK(9, 8) ++# define DSI_TXPKT1C_DISPLAY_NO_SHIFT 8 ++/* Short, trigger, BTA, or a long packet that fits all in CMDFIFO. */ ++# define DSI_TXPKT1C_DISPLAY_NO_SHORT 0 ++/* Primary display where cmdfifo provides part of the payload and ++ * pixelvalve the rest. ++ */ ++# define DSI_TXPKT1C_DISPLAY_NO_PRIMARY 1 ++/* Secondary display where cmdfifo provides part of the payload and ++ * pixfifo the rest. ++ */ ++# define DSI_TXPKT1C_DISPLAY_NO_SECONDARY 2 ++ ++# define DSI_TXPKT1C_CMD_TX_TIME_MASK VC4_MASK(7, 6) ++# define DSI_TXPKT1C_CMD_TX_TIME_SHIFT 6 ++ ++# define DSI_TXPKT1C_CMD_CTRL_MASK VC4_MASK(5, 4) ++# define DSI_TXPKT1C_CMD_CTRL_SHIFT 4 ++/* Command only. Uses TXPKT1H and DISPLAY_NO */ ++# define DSI_TXPKT1C_CMD_CTRL_TX 0 ++/* Command with BTA for either ack or read data. */ ++# define DSI_TXPKT1C_CMD_CTRL_RX 1 ++/* Trigger according to TRIG_CMD */ ++# define DSI_TXPKT1C_CMD_CTRL_TRIG 2 ++/* BTA alone for getting error status after a command, or a TE trigger ++ * without a previous command. ++ */ ++# define DSI_TXPKT1C_CMD_CTRL_BTA 3 ++ ++# define DSI_TXPKT1C_CMD_MODE_LP BIT(3) ++# define DSI_TXPKT1C_CMD_TYPE_LONG BIT(2) ++# define DSI_TXPKT1C_CMD_TE_EN BIT(1) ++# define DSI_TXPKT1C_CMD_EN BIT(0) ++ ++/* Command packet header. */ ++#define DSI0_TXPKT1H 0x08 /* AKA PKTH */ ++#define DSI1_TXPKT1H 0x08 ++# define DSI_TXPKT1H_BC_CMDFIFO_MASK VC4_MASK(31, 24) ++# define DSI_TXPKT1H_BC_CMDFIFO_SHIFT 24 ++# define DSI_TXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8) ++# define DSI_TXPKT1H_BC_PARAM_SHIFT 8 ++# define DSI_TXPKT1H_BC_DT_MASK VC4_MASK(7, 0) ++# define DSI_TXPKT1H_BC_DT_SHIFT 0 ++ ++#define DSI0_RXPKT1H 0x0c /* AKA RX1_PKTH */ ++#define DSI1_RXPKT1H 0x14 ++# define DSI_RXPKT1H_CRC_ERR BIT(31) ++# define DSI_RXPKT1H_DET_ERR BIT(30) ++# define DSI_RXPKT1H_ECC_ERR BIT(29) ++# define DSI_RXPKT1H_COR_ERR BIT(28) ++# define DSI_RXPKT1H_INCOMP_PKT BIT(25) ++# define DSI_RXPKT1H_PKT_TYPE_LONG BIT(24) ++/* Byte count if DSI_RXPKT1H_PKT_TYPE_LONG */ ++# define DSI_RXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8) ++# define DSI_RXPKT1H_BC_PARAM_SHIFT 8 ++/* Short return bytes if !DSI_RXPKT1H_PKT_TYPE_LONG */ ++# define DSI_RXPKT1H_SHORT_1_MASK VC4_MASK(23, 16) ++# define DSI_RXPKT1H_SHORT_1_SHIFT 16 ++# define DSI_RXPKT1H_SHORT_0_MASK VC4_MASK(15, 8) ++# define DSI_RXPKT1H_SHORT_0_SHIFT 8 ++# define DSI_RXPKT1H_DT_LP_CMD_MASK VC4_MASK(7, 0) ++# define DSI_RXPKT1H_DT_LP_CMD_SHIFT 0 ++ ++#define DSI0_RXPKT2H 0x10 /* AKA RX2_PKTH */ ++#define DSI1_RXPKT2H 0x18 ++# define DSI_RXPKT1H_DET_ERR BIT(30) ++# define DSI_RXPKT1H_ECC_ERR BIT(29) ++# define DSI_RXPKT1H_COR_ERR BIT(28) ++# define DSI_RXPKT1H_INCOMP_PKT BIT(25) ++# define DSI_RXPKT1H_BC_PARAM_MASK VC4_MASK(23, 8) ++# define DSI_RXPKT1H_BC_PARAM_SHIFT 8 ++# define DSI_RXPKT1H_DT_MASK VC4_MASK(7, 0) ++# define DSI_RXPKT1H_DT_SHIFT 0 ++ ++#define DSI0_TXPKT_CMD_FIFO 0x14 /* AKA CMD_DATAF */ ++#define DSI1_TXPKT_CMD_FIFO 0x1c ++ ++#define DSI0_DISP0_CTRL 0x18 ++# define DSI_DISP0_PIX_CLK_DIV_MASK VC4_MASK(21, 13) ++# define DSI_DISP0_PIX_CLK_DIV_SHIFT 13 ++# define DSI_DISP0_LP_STOP_CTRL_MASK VC4_MASK(12, 11) ++# define DSI_DISP0_LP_STOP_CTRL_SHIFT 11 ++# define DSI_DISP0_LP_STOP_DISABLE 0 ++# define DSI_DISP0_LP_STOP_PERLINE 1 ++# define DSI_DISP0_LP_STOP_PERFRAME 2 ++ ++/* Transmit RGB pixels and null packets only during HACTIVE, instead ++ * of going to LP-STOP. ++ */ ++# define DSI_DISP_HACTIVE_NULL BIT(10) ++/* Transmit blanking packet only during vblank, instead of allowing LP-STOP. */ ++# define DSI_DISP_VBLP_CTRL BIT(9) ++/* Transmit blanking packet only during HFP, instead of allowing LP-STOP. */ ++# define DSI_DISP_HFP_CTRL BIT(8) ++/* Transmit blanking packet only during HBP, instead of allowing LP-STOP. */ ++# define DSI_DISP_HBP_CTRL BIT(7) ++# define DSI_DISP0_CHANNEL_MASK VC4_MASK(6, 5) ++# define DSI_DISP0_CHANNEL_SHIFT 5 ++/* Enables end events for HSYNC/VSYNC, not just start events. */ ++# define DSI_DISP0_ST_END BIT(4) ++# define DSI_DISP0_PFORMAT_MASK VC4_MASK(3, 2) ++# define DSI_DISP0_PFORMAT_SHIFT 2 ++# define DSI_PFORMAT_RGB565 0 ++# define DSI_PFORMAT_RGB666_PACKED 1 ++# define DSI_PFORMAT_RGB666 2 ++# define DSI_PFORMAT_RGB888 3 ++/* Default is VIDEO mode. */ ++# define DSI_DISP0_COMMAND_MODE BIT(1) ++# define DSI_DISP0_ENABLE BIT(0) ++ ++#define DSI0_DISP1_CTRL 0x1c ++#define DSI1_DISP1_CTRL 0x2c ++/* Format of the data written to TXPKT_PIX_FIFO. */ ++# define DSI_DISP1_PFORMAT_MASK VC4_MASK(2, 1) ++# define DSI_DISP1_PFORMAT_SHIFT 1 ++# define DSI_DISP1_PFORMAT_16BIT 0 ++# define DSI_DISP1_PFORMAT_24BIT 1 ++# define DSI_DISP1_PFORMAT_32BIT_LE 2 ++# define DSI_DISP1_PFORMAT_32BIT_BE 3 ++ ++/* DISP1 is always command mode. */ ++# define DSI_DISP1_ENABLE BIT(0) ++ ++#define DSI0_TXPKT_PIX_FIFO 0x20 /* AKA PIX_FIFO */ ++ ++#define DSI0_INT_STAT 0x24 ++#define DSI0_INT_EN 0x28 ++# define DSI1_INT_PHY_D3_ULPS BIT(30) ++# define DSI1_INT_PHY_D3_STOP BIT(29) ++# define DSI1_INT_PHY_D2_ULPS BIT(28) ++# define DSI1_INT_PHY_D2_STOP BIT(27) ++# define DSI1_INT_PHY_D1_ULPS BIT(26) ++# define DSI1_INT_PHY_D1_STOP BIT(25) ++# define DSI1_INT_PHY_D0_ULPS BIT(24) ++# define DSI1_INT_PHY_D0_STOP BIT(23) ++# define DSI1_INT_FIFO_ERR BIT(22) ++# define DSI1_INT_PHY_DIR_RTF BIT(21) ++# define DSI1_INT_PHY_RXLPDT BIT(20) ++# define DSI1_INT_PHY_RXTRIG BIT(19) ++# define DSI1_INT_PHY_D0_LPDT BIT(18) ++# define DSI1_INT_PHY_DIR_FTR BIT(17) ++ ++/* Signaled when the clock lane enters the given state. */ ++# define DSI1_INT_PHY_CLOCK_ULPS BIT(16) ++# define DSI1_INT_PHY_CLOCK_HS BIT(15) ++# define DSI1_INT_PHY_CLOCK_STOP BIT(14) ++ ++/* Signaled on timeouts */ ++# define DSI1_INT_PR_TO BIT(13) ++# define DSI1_INT_TA_TO BIT(12) ++# define DSI1_INT_LPRX_TO BIT(11) ++# define DSI1_INT_HSTX_TO BIT(10) ++ ++/* Contention on a line when trying to drive the line low */ ++# define DSI1_INT_ERR_CONT_LP1 BIT(9) ++# define DSI1_INT_ERR_CONT_LP0 BIT(8) ++ ++/* Control error: incorrect line state sequence on data lane 0. */ ++# define DSI1_INT_ERR_CONTROL BIT(7) ++/* LPDT synchronization error (bits received not a multiple of 8. */ ++ ++# define DSI1_INT_ERR_SYNC_ESC BIT(6) ++/* Signaled after receiving an error packet from the display in ++ * response to a read. ++ */ ++# define DSI1_INT_RXPKT2 BIT(5) ++/* Signaled after receiving a packet. The header and optional short ++ * response will be in RXPKT1H, and a long response will be in the ++ * RXPKT_FIFO. ++ */ ++# define DSI1_INT_RXPKT1 BIT(4) ++# define DSI1_INT_TXPKT2_DONE BIT(3) ++# define DSI1_INT_TXPKT2_END BIT(2) ++/* Signaled after all repeats of TXPKT1 are transferred. */ ++# define DSI1_INT_TXPKT1_DONE BIT(1) ++/* Signaled after each TXPKT1 repeat is scheduled. */ ++# define DSI1_INT_TXPKT1_END BIT(0) ++ ++#define DSI1_INTERRUPTS_ALWAYS_ENABLED (DSI1_INT_ERR_SYNC_ESC | \ ++ DSI1_INT_ERR_CONTROL | \ ++ DSI1_INT_ERR_CONT_LP0 | \ ++ DSI1_INT_ERR_CONT_LP1 | \ ++ DSI1_INT_HSTX_TO | \ ++ DSI1_INT_LPRX_TO | \ ++ DSI1_INT_TA_TO | \ ++ DSI1_INT_PR_TO) ++ ++#define DSI0_STAT 0x2c ++#define DSI0_HSTX_TO_CNT 0x30 ++#define DSI0_LPRX_TO_CNT 0x34 ++#define DSI0_TA_TO_CNT 0x38 ++#define DSI0_PR_TO_CNT 0x3c ++#define DSI0_PHYC 0x40 ++# define DSI1_PHYC_ESC_CLK_LPDT_MASK VC4_MASK(25, 20) ++# define DSI1_PHYC_ESC_CLK_LPDT_SHIFT 20 ++# define DSI1_PHYC_HS_CLK_CONTINUOUS BIT(18) ++# define DSI0_PHYC_ESC_CLK_LPDT_MASK VC4_MASK(17, 12) ++# define DSI0_PHYC_ESC_CLK_LPDT_SHIFT 12 ++# define DSI1_PHYC_CLANE_ULPS BIT(17) ++# define DSI1_PHYC_CLANE_ENABLE BIT(16) ++# define DSI_PHYC_DLANE3_ULPS BIT(13) ++# define DSI_PHYC_DLANE3_ENABLE BIT(12) ++# define DSI0_PHYC_HS_CLK_CONTINUOUS BIT(10) ++# define DSI0_PHYC_CLANE_ULPS BIT(9) ++# define DSI_PHYC_DLANE2_ULPS BIT(9) ++# define DSI0_PHYC_CLANE_ENABLE BIT(8) ++# define DSI_PHYC_DLANE2_ENABLE BIT(8) ++# define DSI_PHYC_DLANE1_ULPS BIT(5) ++# define DSI_PHYC_DLANE1_ENABLE BIT(4) ++# define DSI_PHYC_DLANE0_FORCE_STOP BIT(2) ++# define DSI_PHYC_DLANE0_ULPS BIT(1) ++# define DSI_PHYC_DLANE0_ENABLE BIT(0) ++ ++#define DSI0_HS_CLT0 0x44 ++#define DSI0_HS_CLT1 0x48 ++#define DSI0_HS_CLT2 0x4c ++#define DSI0_HS_DLT3 0x50 ++#define DSI0_HS_DLT4 0x54 ++#define DSI0_HS_DLT5 0x58 ++#define DSI0_HS_DLT6 0x5c ++#define DSI0_HS_DLT7 0x60 ++ ++#define DSI0_PHY_AFEC0 0x64 ++# define DSI0_PHY_AFEC0_DDR2CLK_EN BIT(26) ++# define DSI0_PHY_AFEC0_DDRCLK_EN BIT(25) ++# define DSI0_PHY_AFEC0_LATCH_ULPS BIT(24) ++# define DSI1_PHY_AFEC0_IDR_DLANE3_MASK VC4_MASK(31, 29) ++# define DSI1_PHY_AFEC0_IDR_DLANE3_SHIFT 29 ++# define DSI1_PHY_AFEC0_IDR_DLANE2_MASK VC4_MASK(28, 26) ++# define DSI1_PHY_AFEC0_IDR_DLANE2_SHIFT 26 ++# define DSI1_PHY_AFEC0_IDR_DLANE1_MASK VC4_MASK(27, 23) ++# define DSI1_PHY_AFEC0_IDR_DLANE1_SHIFT 23 ++# define DSI1_PHY_AFEC0_IDR_DLANE0_MASK VC4_MASK(22, 20) ++# define DSI1_PHY_AFEC0_IDR_DLANE0_SHIFT 20 ++# define DSI1_PHY_AFEC0_IDR_CLANE_MASK VC4_MASK(19, 17) ++# define DSI1_PHY_AFEC0_IDR_CLANE_SHIFT 17 ++# define DSI0_PHY_AFEC0_ACTRL_DLANE1_MASK VC4_MASK(23, 20) ++# define DSI0_PHY_AFEC0_ACTRL_DLANE1_SHIFT 20 ++# define DSI0_PHY_AFEC0_ACTRL_DLANE0_MASK VC4_MASK(19, 16) ++# define DSI0_PHY_AFEC0_ACTRL_DLANE0_SHIFT 16 ++# define DSI0_PHY_AFEC0_ACTRL_CLANE_MASK VC4_MASK(15, 12) ++# define DSI0_PHY_AFEC0_ACTRL_CLANE_SHIFT 12 ++# define DSI1_PHY_AFEC0_DDR2CLK_EN BIT(16) ++# define DSI1_PHY_AFEC0_DDRCLK_EN BIT(15) ++# define DSI1_PHY_AFEC0_LATCH_ULPS BIT(14) ++# define DSI1_PHY_AFEC0_RESET BIT(13) ++# define DSI1_PHY_AFEC0_PD BIT(12) ++# define DSI0_PHY_AFEC0_RESET BIT(11) ++# define DSI1_PHY_AFEC0_PD_BG BIT(11) ++# define DSI0_PHY_AFEC0_PD BIT(10) ++# define DSI1_PHY_AFEC0_PD_DLANE3 BIT(10) ++# define DSI0_PHY_AFEC0_PD_BG BIT(9) ++# define DSI1_PHY_AFEC0_PD_DLANE2 BIT(9) ++# define DSI0_PHY_AFEC0_PD_DLANE1 BIT(8) ++# define DSI1_PHY_AFEC0_PD_DLANE1 BIT(8) ++# define DSI_PHY_AFEC0_PTATADJ_MASK VC4_MASK(7, 4) ++# define DSI_PHY_AFEC0_PTATADJ_SHIFT 4 ++# define DSI_PHY_AFEC0_CTATADJ_MASK VC4_MASK(3, 0) ++# define DSI_PHY_AFEC0_CTATADJ_SHIFT 0 ++ ++#define DSI0_PHY_AFEC1 0x68 ++# define DSI0_PHY_AFEC1_IDR_DLANE1_MASK VC4_MASK(10, 8) ++# define DSI0_PHY_AFEC1_IDR_DLANE1_SHIFT 8 ++# define DSI0_PHY_AFEC1_IDR_DLANE0_MASK VC4_MASK(6, 4) ++# define DSI0_PHY_AFEC1_IDR_DLANE0_SHIFT 4 ++# define DSI0_PHY_AFEC1_IDR_CLANE_MASK VC4_MASK(2, 0) ++# define DSI0_PHY_AFEC1_IDR_CLANE_SHIFT 0 ++ ++#define DSI0_TST_SEL 0x6c ++#define DSI0_TST_MON 0x70 ++#define DSI0_ID 0x74 ++# define DSI_ID_VALUE 0x00647369 ++ ++#define DSI1_CTRL 0x00 ++# define DSI_CTRL_HS_CLKC_MASK VC4_MASK(15, 14) ++# define DSI_CTRL_HS_CLKC_SHIFT 14 ++# define DSI_CTRL_HS_CLKC_BYTE 0 ++# define DSI_CTRL_HS_CLKC_DDR2 1 ++# define DSI_CTRL_HS_CLKC_DDR 2 ++ ++# define DSI_CTRL_RX_LPDT_EOT_DISABLE BIT(13) ++# define DSI_CTRL_LPDT_EOT_DISABLE BIT(12) ++# define DSI_CTRL_HSDT_EOT_DISABLE BIT(11) ++# define DSI_CTRL_SOFT_RESET_CFG BIT(10) ++# define DSI_CTRL_CAL_BYTE BIT(9) ++# define DSI_CTRL_INV_BYTE BIT(8) ++# define DSI_CTRL_CLR_LDF BIT(7) ++# define DSI0_CTRL_CLR_PBCF BIT(6) ++# define DSI1_CTRL_CLR_RXF BIT(6) ++# define DSI0_CTRL_CLR_CPBCF BIT(5) ++# define DSI1_CTRL_CLR_PDF BIT(5) ++# define DSI0_CTRL_CLR_PDF BIT(4) ++# define DSI1_CTRL_CLR_CDF BIT(4) ++# define DSI0_CTRL_CLR_CDF BIT(3) ++# define DSI0_CTRL_CTRL2 BIT(2) ++# define DSI1_CTRL_DISABLE_DISP_CRCC BIT(2) ++# define DSI0_CTRL_CTRL1 BIT(1) ++# define DSI1_CTRL_DISABLE_DISP_ECCC BIT(1) ++# define DSI0_CTRL_CTRL0 BIT(0) ++# define DSI1_CTRL_EN BIT(0) ++# define DSI0_CTRL_RESET_FIFOS (DSI_CTRL_CLR_LDF | \ ++ DSI0_CTRL_CLR_PBCF | \ ++ DSI0_CTRL_CLR_CPBCF | \ ++ DSI0_CTRL_CLR_PDF | \ ++ DSI0_CTRL_CLR_CDF) ++# define DSI1_CTRL_RESET_FIFOS (DSI_CTRL_CLR_LDF | \ ++ DSI1_CTRL_CLR_RXF | \ ++ DSI1_CTRL_CLR_PDF | \ ++ DSI1_CTRL_CLR_CDF) ++ ++#define DSI1_TXPKT2C 0x0c ++#define DSI1_TXPKT2H 0x10 ++#define DSI1_TXPKT_PIX_FIFO 0x20 ++#define DSI1_RXPKT_FIFO 0x24 ++#define DSI1_DISP0_CTRL 0x28 ++#define DSI1_INT_STAT 0x30 ++#define DSI1_INT_EN 0x34 ++/* State reporting bits. These mostly behave like INT_STAT, where ++ * writing a 1 clears the bit. ++ */ ++#define DSI1_STAT 0x38 ++# define DSI1_STAT_PHY_D3_ULPS BIT(31) ++# define DSI1_STAT_PHY_D3_STOP BIT(30) ++# define DSI1_STAT_PHY_D2_ULPS BIT(29) ++# define DSI1_STAT_PHY_D2_STOP BIT(28) ++# define DSI1_STAT_PHY_D1_ULPS BIT(27) ++# define DSI1_STAT_PHY_D1_STOP BIT(26) ++# define DSI1_STAT_PHY_D0_ULPS BIT(25) ++# define DSI1_STAT_PHY_D0_STOP BIT(24) ++# define DSI1_STAT_FIFO_ERR BIT(23) ++# define DSI1_STAT_PHY_RXLPDT BIT(22) ++# define DSI1_STAT_PHY_RXTRIG BIT(21) ++# define DSI1_STAT_PHY_D0_LPDT BIT(20) ++/* Set when in forward direction */ ++# define DSI1_STAT_PHY_DIR BIT(19) ++# define DSI1_STAT_PHY_CLOCK_ULPS BIT(18) ++# define DSI1_STAT_PHY_CLOCK_HS BIT(17) ++# define DSI1_STAT_PHY_CLOCK_STOP BIT(16) ++# define DSI1_STAT_PR_TO BIT(15) ++# define DSI1_STAT_TA_TO BIT(14) ++# define DSI1_STAT_LPRX_TO BIT(13) ++# define DSI1_STAT_HSTX_TO BIT(12) ++# define DSI1_STAT_ERR_CONT_LP1 BIT(11) ++# define DSI1_STAT_ERR_CONT_LP0 BIT(10) ++# define DSI1_STAT_ERR_CONTROL BIT(9) ++# define DSI1_STAT_ERR_SYNC_ESC BIT(8) ++# define DSI1_STAT_RXPKT2 BIT(7) ++# define DSI1_STAT_RXPKT1 BIT(6) ++# define DSI1_STAT_TXPKT2_BUSY BIT(5) ++# define DSI1_STAT_TXPKT2_DONE BIT(4) ++# define DSI1_STAT_TXPKT2_END BIT(3) ++# define DSI1_STAT_TXPKT1_BUSY BIT(2) ++# define DSI1_STAT_TXPKT1_DONE BIT(1) ++# define DSI1_STAT_TXPKT1_END BIT(0) ++ ++#define DSI1_HSTX_TO_CNT 0x3c ++#define DSI1_LPRX_TO_CNT 0x40 ++#define DSI1_TA_TO_CNT 0x44 ++#define DSI1_PR_TO_CNT 0x48 ++#define DSI1_PHYC 0x4c ++ ++#define DSI1_HS_CLT0 0x50 ++# define DSI_HS_CLT0_CZERO_MASK VC4_MASK(26, 18) ++# define DSI_HS_CLT0_CZERO_SHIFT 18 ++# define DSI_HS_CLT0_CPRE_MASK VC4_MASK(17, 9) ++# define DSI_HS_CLT0_CPRE_SHIFT 9 ++# define DSI_HS_CLT0_CPREP_MASK VC4_MASK(8, 0) ++# define DSI_HS_CLT0_CPREP_SHIFT 0 ++ ++#define DSI1_HS_CLT1 0x54 ++# define DSI_HS_CLT1_CTRAIL_MASK VC4_MASK(17, 9) ++# define DSI_HS_CLT1_CTRAIL_SHIFT 9 ++# define DSI_HS_CLT1_CPOST_MASK VC4_MASK(8, 0) ++# define DSI_HS_CLT1_CPOST_SHIFT 0 ++ ++#define DSI1_HS_CLT2 0x58 ++# define DSI_HS_CLT2_WUP_MASK VC4_MASK(23, 0) ++# define DSI_HS_CLT2_WUP_SHIFT 0 ++ ++#define DSI1_HS_DLT3 0x5c ++# define DSI_HS_DLT3_EXIT_MASK VC4_MASK(26, 18) ++# define DSI_HS_DLT3_EXIT_SHIFT 18 ++# define DSI_HS_DLT3_ZERO_MASK VC4_MASK(17, 9) ++# define DSI_HS_DLT3_ZERO_SHIFT 9 ++# define DSI_HS_DLT3_PRE_MASK VC4_MASK(8, 0) ++# define DSI_HS_DLT3_PRE_SHIFT 0 ++ ++#define DSI1_HS_DLT4 0x60 ++# define DSI_HS_DLT4_ANLAT_MASK VC4_MASK(22, 18) ++# define DSI_HS_DLT4_ANLAT_SHIFT 18 ++# define DSI_HS_DLT4_TRAIL_MASK VC4_MASK(17, 9) ++# define DSI_HS_DLT4_TRAIL_SHIFT 9 ++# define DSI_HS_DLT4_LPX_MASK VC4_MASK(8, 0) ++# define DSI_HS_DLT4_LPX_SHIFT 0 ++ ++#define DSI1_HS_DLT5 0x64 ++# define DSI_HS_DLT5_INIT_MASK VC4_MASK(23, 0) ++# define DSI_HS_DLT5_INIT_SHIFT 0 ++ ++#define DSI1_HS_DLT6 0x68 ++# define DSI_HS_DLT6_TA_GET_MASK VC4_MASK(31, 24) ++# define DSI_HS_DLT6_TA_GET_SHIFT 24 ++# define DSI_HS_DLT6_TA_SURE_MASK VC4_MASK(23, 16) ++# define DSI_HS_DLT6_TA_SURE_SHIFT 16 ++# define DSI_HS_DLT6_TA_GO_MASK VC4_MASK(15, 8) ++# define DSI_HS_DLT6_TA_GO_SHIFT 8 ++# define DSI_HS_DLT6_LP_LPX_MASK VC4_MASK(7, 0) ++# define DSI_HS_DLT6_LP_LPX_SHIFT 0 ++ ++#define DSI1_HS_DLT7 0x6c ++# define DSI_HS_DLT7_LP_WUP_MASK VC4_MASK(23, 0) ++# define DSI_HS_DLT7_LP_WUP_SHIFT 0 ++ ++#define DSI1_PHY_AFEC0 0x70 ++ ++#define DSI1_PHY_AFEC1 0x74 ++# define DSI1_PHY_AFEC1_ACTRL_DLANE3_MASK VC4_MASK(19, 16) ++# define DSI1_PHY_AFEC1_ACTRL_DLANE3_SHIFT 16 ++# define DSI1_PHY_AFEC1_ACTRL_DLANE2_MASK VC4_MASK(15, 12) ++# define DSI1_PHY_AFEC1_ACTRL_DLANE2_SHIFT 12 ++# define DSI1_PHY_AFEC1_ACTRL_DLANE1_MASK VC4_MASK(11, 8) ++# define DSI1_PHY_AFEC1_ACTRL_DLANE1_SHIFT 8 ++# define DSI1_PHY_AFEC1_ACTRL_DLANE0_MASK VC4_MASK(7, 4) ++# define DSI1_PHY_AFEC1_ACTRL_DLANE0_SHIFT 4 ++# define DSI1_PHY_AFEC1_ACTRL_CLANE_MASK VC4_MASK(3, 0) ++# define DSI1_PHY_AFEC1_ACTRL_CLANE_SHIFT 0 ++ ++#define DSI1_TST_SEL 0x78 ++#define DSI1_TST_MON 0x7c ++#define DSI1_PHY_TST1 0x80 ++#define DSI1_PHY_TST2 0x84 ++#define DSI1_PHY_FIFO_STAT 0x88 ++/* Actually, all registers in the range that aren't otherwise claimed ++ * will return the ID. ++ */ ++#define DSI1_ID 0x8c ++ ++/* General DSI hardware state. */ ++struct vc4_dsi { ++ struct platform_device *pdev; ++ ++ struct mipi_dsi_host dsi_host; ++ struct drm_encoder *encoder; ++ struct drm_connector *connector; ++ struct drm_panel *panel; ++ ++ void __iomem *regs; ++ ++ struct dma_chan *reg_dma_chan; ++ dma_addr_t reg_dma_paddr; ++ u32 *reg_dma_mem; ++ dma_addr_t reg_paddr; ++ ++ /* Whether we're on bcm2835's DSI0 or DSI1. */ ++ int port; ++ ++ /* DSI channel for the panel we're connected to. */ ++ u32 channel; ++ u32 lanes; ++ enum mipi_dsi_pixel_format format; ++ u32 mode_flags; ++ ++ /* Input clock from CPRMAN to the digital PHY, for the DSI ++ * escape clock. ++ */ ++ struct clk *escape_clock; ++ ++ /* Input clock to the analog PHY, used to generate the DSI bit ++ * clock. ++ */ ++ struct clk *pll_phy_clock; ++ ++ /* HS Clocks generated within the DSI analog PHY. */ ++ struct clk_fixed_factor phy_clocks[3]; ++ ++ struct clk_onecell_data clk_onecell; ++ ++ /* Pixel clock output to the pixelvalve, generated from the HS ++ * clock. ++ */ ++ struct clk *pixel_clock; ++ ++ struct completion xfer_completion; ++ int xfer_result; ++}; ++ ++#define host_to_dsi(host) container_of(host, struct vc4_dsi, dsi_host) ++ ++static inline void ++dsi_dma_workaround_write(struct vc4_dsi *dsi, u32 offset, u32 val) ++{ ++ struct dma_chan *chan = dsi->reg_dma_chan; ++ struct dma_async_tx_descriptor *tx; ++ dma_cookie_t cookie; ++ int ret; ++ ++ /* DSI0 should be able to write normally. */ ++ if (!chan) { ++ writel(val, dsi->regs + offset); ++ return; ++ } ++ ++ *dsi->reg_dma_mem = val; ++ ++ tx = chan->device->device_prep_dma_memcpy(chan, ++ dsi->reg_paddr + offset, ++ dsi->reg_dma_paddr, ++ 4, 0); ++ if (!tx) { ++ DRM_ERROR("Failed to set up DMA register write\n"); ++ return; ++ } ++ ++ cookie = tx->tx_submit(tx); ++ ret = dma_submit_error(cookie); ++ if (ret) { ++ DRM_ERROR("Failed to submit DMA: %d\n", ret); ++ return; ++ } ++ ret = dma_sync_wait(chan, cookie); ++ if (ret) ++ DRM_ERROR("Failed to wait for DMA: %d\n", ret); ++} ++ ++#define DSI_READ(offset) readl(dsi->regs + (offset)) ++#define DSI_WRITE(offset, val) dsi_dma_workaround_write(dsi, offset, val) ++#define DSI_PORT_READ(offset) \ ++ DSI_READ(dsi->port ? DSI1_##offset : DSI0_##offset) ++#define DSI_PORT_WRITE(offset, val) \ ++ DSI_WRITE(dsi->port ? DSI1_##offset : DSI0_##offset, val) ++#define DSI_PORT_BIT(bit) (dsi->port ? DSI1_##bit : DSI0_##bit) ++ ++/* VC4 DSI encoder KMS struct */ ++struct vc4_dsi_encoder { ++ struct vc4_encoder base; ++ struct vc4_dsi *dsi; ++}; ++ ++static inline struct vc4_dsi_encoder * ++to_vc4_dsi_encoder(struct drm_encoder *encoder) ++{ ++ return container_of(encoder, struct vc4_dsi_encoder, base.base); ++} ++ ++/* VC4 DSI connector KMS struct */ ++struct vc4_dsi_connector { ++ struct drm_connector base; ++ struct vc4_dsi *dsi; ++}; ++ ++static inline struct vc4_dsi_connector * ++to_vc4_dsi_connector(struct drm_connector *connector) ++{ ++ return container_of(connector, struct vc4_dsi_connector, base); ++} ++ ++#define DSI_REG(reg) { reg, #reg } ++static const struct { ++ u32 reg; ++ const char *name; ++} dsi0_regs[] = { ++ DSI_REG(DSI0_CTRL), ++ DSI_REG(DSI0_STAT), ++ DSI_REG(DSI0_HSTX_TO_CNT), ++ DSI_REG(DSI0_LPRX_TO_CNT), ++ DSI_REG(DSI0_TA_TO_CNT), ++ DSI_REG(DSI0_PR_TO_CNT), ++ DSI_REG(DSI0_DISP0_CTRL), ++ DSI_REG(DSI0_DISP1_CTRL), ++ DSI_REG(DSI0_INT_STAT), ++ DSI_REG(DSI0_INT_EN), ++ DSI_REG(DSI0_PHYC), ++ DSI_REG(DSI0_HS_CLT0), ++ DSI_REG(DSI0_HS_CLT1), ++ DSI_REG(DSI0_HS_CLT2), ++ DSI_REG(DSI0_HS_DLT3), ++ DSI_REG(DSI0_HS_DLT4), ++ DSI_REG(DSI0_HS_DLT5), ++ DSI_REG(DSI0_HS_DLT6), ++ DSI_REG(DSI0_HS_DLT7), ++ DSI_REG(DSI0_PHY_AFEC0), ++ DSI_REG(DSI0_PHY_AFEC1), ++ DSI_REG(DSI0_ID), ++}; ++ ++static const struct { ++ u32 reg; ++ const char *name; ++} dsi1_regs[] = { ++ DSI_REG(DSI1_CTRL), ++ DSI_REG(DSI1_STAT), ++ DSI_REG(DSI1_HSTX_TO_CNT), ++ DSI_REG(DSI1_LPRX_TO_CNT), ++ DSI_REG(DSI1_TA_TO_CNT), ++ DSI_REG(DSI1_PR_TO_CNT), ++ DSI_REG(DSI1_DISP0_CTRL), ++ DSI_REG(DSI1_DISP1_CTRL), ++ DSI_REG(DSI1_INT_STAT), ++ DSI_REG(DSI1_INT_EN), ++ DSI_REG(DSI1_PHYC), ++ DSI_REG(DSI1_HS_CLT0), ++ DSI_REG(DSI1_HS_CLT1), ++ DSI_REG(DSI1_HS_CLT2), ++ DSI_REG(DSI1_HS_DLT3), ++ DSI_REG(DSI1_HS_DLT4), ++ DSI_REG(DSI1_HS_DLT5), ++ DSI_REG(DSI1_HS_DLT6), ++ DSI_REG(DSI1_HS_DLT7), ++ DSI_REG(DSI1_PHY_AFEC0), ++ DSI_REG(DSI1_PHY_AFEC1), ++ DSI_REG(DSI1_ID), ++}; ++ ++static void vc4_dsi_dump_regs(struct vc4_dsi *dsi) ++{ ++ int i; ++ ++ if (dsi->port == 0) { ++ for (i = 0; i < ARRAY_SIZE(dsi0_regs); i++) { ++ DRM_INFO("0x%04x (%s): 0x%08x\n", ++ dsi0_regs[i].reg, dsi0_regs[i].name, ++ DSI_READ(dsi0_regs[i].reg)); ++ } ++ } else { ++ for (i = 0; i < ARRAY_SIZE(dsi1_regs); i++) { ++ DRM_INFO("0x%04x (%s): 0x%08x\n", ++ dsi1_regs[i].reg, dsi1_regs[i].name, ++ DSI_READ(dsi1_regs[i].reg)); ++ } ++ } ++} ++ ++#ifdef CONFIG_DEBUG_FS ++int vc4_dsi_debugfs_regs(struct seq_file *m, void *unused) ++{ ++ struct drm_info_node *node = (struct drm_info_node *)m->private; ++ struct drm_device *drm = node->minor->dev; ++ struct vc4_dev *vc4 = to_vc4_dev(drm); ++ int dsi_index = (uintptr_t)node->info_ent->data; ++ struct vc4_dsi *dsi = (dsi_index == 1 ? vc4->dsi1 : NULL); ++ int i; ++ ++ if (!dsi) ++ return 0; ++ ++ if (dsi->port == 0) { ++ for (i = 0; i < ARRAY_SIZE(dsi0_regs); i++) { ++ seq_printf(m, "0x%04x (%s): 0x%08x\n", ++ dsi0_regs[i].reg, dsi0_regs[i].name, ++ DSI_READ(dsi0_regs[i].reg)); ++ } ++ } else { ++ for (i = 0; i < ARRAY_SIZE(dsi1_regs); i++) { ++ seq_printf(m, "0x%04x (%s): 0x%08x\n", ++ dsi1_regs[i].reg, dsi1_regs[i].name, ++ DSI_READ(dsi1_regs[i].reg)); ++ } ++ } ++ ++ return 0; ++} ++#endif ++ ++static enum drm_connector_status ++vc4_dsi_connector_detect(struct drm_connector *connector, bool force) ++{ ++ struct vc4_dsi_connector *vc4_connector = ++ to_vc4_dsi_connector(connector); ++ struct vc4_dsi *dsi = vc4_connector->dsi; ++ ++ if (dsi->panel) ++ return connector_status_connected; ++ else ++ return connector_status_disconnected; ++} ++ ++static void vc4_dsi_connector_destroy(struct drm_connector *connector) ++{ ++ drm_connector_unregister(connector); ++ drm_connector_cleanup(connector); ++} ++ ++static int vc4_dsi_connector_get_modes(struct drm_connector *connector) ++{ ++ struct vc4_dsi_connector *vc4_connector = ++ to_vc4_dsi_connector(connector); ++ struct vc4_dsi *dsi = vc4_connector->dsi; ++ ++ if (dsi->panel) ++ return drm_panel_get_modes(dsi->panel); ++ ++ return 0; ++} ++ ++static const struct drm_connector_funcs vc4_dsi_connector_funcs = { ++ .dpms = drm_atomic_helper_connector_dpms, ++ .detect = vc4_dsi_connector_detect, ++ .fill_modes = drm_helper_probe_single_connector_modes, ++ .destroy = vc4_dsi_connector_destroy, ++ .reset = drm_atomic_helper_connector_reset, ++ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, ++ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, ++}; ++ ++static const struct drm_connector_helper_funcs vc4_dsi_connector_helper_funcs = { ++ .get_modes = vc4_dsi_connector_get_modes, ++}; ++ ++static struct drm_connector *vc4_dsi_connector_init(struct drm_device *dev, ++ struct vc4_dsi *dsi) ++{ ++ struct drm_connector *connector = NULL; ++ struct vc4_dsi_connector *dsi_connector; ++ int ret = 0; ++ ++ dsi_connector = devm_kzalloc(dev->dev, sizeof(*dsi_connector), ++ GFP_KERNEL); ++ if (!dsi_connector) { ++ ret = -ENOMEM; ++ goto fail; ++ } ++ connector = &dsi_connector->base; ++ ++ dsi_connector->dsi = dsi; ++ ++ drm_connector_init(dev, connector, &vc4_dsi_connector_funcs, ++ DRM_MODE_CONNECTOR_DSI); ++ drm_connector_helper_add(connector, &vc4_dsi_connector_helper_funcs); ++ ++ connector->polled = 0; ++ connector->interlace_allowed = 0; ++ connector->doublescan_allowed = 0; ++ ++ drm_mode_connector_attach_encoder(connector, dsi->encoder); ++ ++ return connector; ++ ++fail: ++ if (connector) ++ vc4_dsi_connector_destroy(connector); ++ ++ return ERR_PTR(ret); ++} ++ ++static void vc4_dsi_encoder_destroy(struct drm_encoder *encoder) ++{ ++ drm_encoder_cleanup(encoder); ++} ++ ++static const struct drm_encoder_funcs vc4_dsi_encoder_funcs = { ++ .destroy = vc4_dsi_encoder_destroy, ++}; ++ ++static void vc4_dsi_latch_ulps(struct vc4_dsi *dsi, bool latch) ++{ ++ u32 afec0 = DSI_PORT_READ(PHY_AFEC0); ++ ++ if (latch) ++ afec0 |= DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS); ++ else ++ afec0 &= ~DSI_PORT_BIT(PHY_AFEC0_LATCH_ULPS); ++ ++ DSI_PORT_WRITE(PHY_AFEC0, afec0); ++} ++ ++/* Enters or exits Ultra Low Power State. */ ++static void vc4_dsi_ulps(struct vc4_dsi *dsi, bool ulps) ++{ ++ bool continuous = dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS; ++ u32 phyc_ulps = ((continuous ? DSI_PORT_BIT(PHYC_CLANE_ULPS) : 0) | ++ DSI_PHYC_DLANE0_ULPS | ++ (dsi->lanes > 1 ? DSI_PHYC_DLANE1_ULPS : 0) | ++ (dsi->lanes > 2 ? DSI_PHYC_DLANE2_ULPS : 0) | ++ (dsi->lanes > 3 ? DSI_PHYC_DLANE3_ULPS : 0)); ++ u32 stat_ulps = ((continuous ? DSI1_STAT_PHY_CLOCK_ULPS : 0) | ++ DSI1_STAT_PHY_D0_ULPS | ++ (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_ULPS : 0) | ++ (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_ULPS : 0) | ++ (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_ULPS : 0)); ++ u32 stat_stop = ((continuous ? DSI1_STAT_PHY_CLOCK_STOP : 0) | ++ DSI1_STAT_PHY_D0_STOP | ++ (dsi->lanes > 1 ? DSI1_STAT_PHY_D1_STOP : 0) | ++ (dsi->lanes > 2 ? DSI1_STAT_PHY_D2_STOP : 0) | ++ (dsi->lanes > 3 ? DSI1_STAT_PHY_D3_STOP : 0)); ++ int ret; ++ ++ DSI_PORT_WRITE(STAT, stat_ulps); ++ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) | phyc_ulps); ++ ret = wait_for((DSI_PORT_READ(STAT) & stat_ulps) == stat_ulps, 200); ++ if (ret) { ++ dev_warn(&dsi->pdev->dev, ++ "Timeout waiting for DSI ULPS entry: STAT 0x%08x", ++ DSI_PORT_READ(STAT)); ++ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps); ++ vc4_dsi_latch_ulps(dsi, false); ++ return; ++ } ++ ++ /* The DSI module can't be disabled while the module is ++ * generating ULPS state. So, to be able to disable the ++ * module, we have the AFE latch the ULPS state and continue ++ * on to having the module enter STOP. ++ */ ++ vc4_dsi_latch_ulps(dsi, ulps); ++ ++ DSI_PORT_WRITE(STAT, stat_stop); ++ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps); ++ ret = wait_for((DSI_PORT_READ(STAT) & stat_stop) == stat_stop, 200); ++ if (ret) { ++ dev_warn(&dsi->pdev->dev, ++ "Timeout waiting for DSI STOP entry: STAT 0x%08x", ++ DSI_PORT_READ(STAT)); ++ DSI_PORT_WRITE(PHYC, DSI_PORT_READ(PHYC) & ~phyc_ulps); ++ return; ++ } ++} ++ ++static u32 ++dsi_hs_timing(u32 ui_ns, u32 ns, u32 ui) ++{ ++ /* The HS timings have to be rounded up to a multiple of 8 ++ * because we're using the byte clock. ++ */ ++ return roundup(ui + DIV_ROUND_UP(ns, ui_ns), 8); ++} ++ ++/* ESC always runs at 100Mhz. */ ++#define ESC_TIME_NS 10 ++ ++static u32 ++dsi_esc_timing(u32 ns) ++{ ++ return DIV_ROUND_UP(ns, ESC_TIME_NS); ++} ++ ++static void vc4_dsi_encoder_disable(struct drm_encoder *encoder) ++{ ++ struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder); ++ struct vc4_dsi *dsi = vc4_encoder->dsi; ++ struct device *dev = &dsi->pdev->dev; ++ ++ drm_panel_disable(dsi->panel); ++ ++ vc4_dsi_ulps(dsi, true); ++ ++ drm_panel_unprepare(dsi->panel); ++ ++ clk_disable_unprepare(dsi->pll_phy_clock); ++ clk_disable_unprepare(dsi->escape_clock); ++ clk_disable_unprepare(dsi->pixel_clock); ++ ++ pm_runtime_put(dev); ++} ++ ++static void vc4_dsi_encoder_enable(struct drm_encoder *encoder) ++{ ++ struct drm_display_mode *mode = &encoder->crtc->mode; ++ struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder); ++ struct vc4_dsi *dsi = vc4_encoder->dsi; ++ struct device *dev = &dsi->pdev->dev; ++ u32 format = 0, divider = 0; ++ bool debug_dump_regs = false; ++ unsigned long hs_clock; ++ u32 ui_ns; ++ /* Minimum LP state duration in escape clock cycles. */ ++ u32 lpx = dsi_esc_timing(60); ++ unsigned long pixel_clock_hz = mode->clock * 1000; ++ unsigned long dsip_clock; ++ unsigned long phy_clock; ++ int ret; ++ ++ ret = pm_runtime_get_sync(dev); ++ if (ret) { ++ DRM_ERROR("Failed to runtime PM enable on DSI%d\n", dsi->port); ++ return; ++ } ++ ++ ret = drm_panel_prepare(dsi->panel); ++ if (ret) { ++ DRM_ERROR("Panel failed to prepare\n"); ++ return; ++ } ++ ++ if (debug_dump_regs) { ++ DRM_INFO("DSI regs before:\n"); ++ vc4_dsi_dump_regs(dsi); ++ } ++ ++ switch (dsi->format) { ++ case MIPI_DSI_FMT_RGB888: ++ format = DSI_PFORMAT_RGB888; ++ divider = 24 / dsi->lanes; ++ break; ++ case MIPI_DSI_FMT_RGB666: ++ format = DSI_PFORMAT_RGB666; ++ divider = 24 / dsi->lanes; ++ break; ++ case MIPI_DSI_FMT_RGB666_PACKED: ++ format = DSI_PFORMAT_RGB666_PACKED; ++ divider = 18 / dsi->lanes; ++ break; ++ case MIPI_DSI_FMT_RGB565: ++ format = DSI_PFORMAT_RGB565; ++ divider = 16 / dsi->lanes; ++ break; ++ } ++ ++ phy_clock = pixel_clock_hz * divider; ++ ret = clk_set_rate(dsi->pll_phy_clock, phy_clock); ++ if (ret) { ++ dev_err(&dsi->pdev->dev, ++ "Failed to set phy clock to %ld: %d\n", phy_clock, ret); ++ } ++ ++ /* Reset the DSI and all its fifos. */ ++ DSI_PORT_WRITE(CTRL, ++ DSI_CTRL_SOFT_RESET_CFG | ++ DSI_PORT_BIT(CTRL_RESET_FIFOS)); ++ ++ DSI_PORT_WRITE(CTRL, ++ DSI_CTRL_HSDT_EOT_DISABLE | ++ DSI_CTRL_RX_LPDT_EOT_DISABLE); ++ ++ /* Clear all stat bits so we see what has happened during enable. */ ++ DSI_PORT_WRITE(STAT, DSI_PORT_READ(STAT)); ++ ++ /* Set AFE CTR00/CTR1 to release powerdown of analog. */ ++ if (dsi->port == 0) { ++ u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) | ++ VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ)); ++ ++ if (dsi->lanes < 2) ++ afec0 |= DSI0_PHY_AFEC0_PD_DLANE1; ++ ++ if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) ++ afec0 |= DSI0_PHY_AFEC0_RESET; ++ ++ DSI_PORT_WRITE(PHY_AFEC0, afec0); ++ ++ DSI_PORT_WRITE(PHY_AFEC1, ++ VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_DLANE1) | ++ VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_DLANE0) | ++ VC4_SET_FIELD(6, DSI0_PHY_AFEC1_IDR_CLANE)); ++ } else { ++ u32 afec0 = (VC4_SET_FIELD(7, DSI_PHY_AFEC0_PTATADJ) | ++ VC4_SET_FIELD(7, DSI_PHY_AFEC0_CTATADJ) | ++ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_CLANE) | ++ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE0) | ++ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE1) | ++ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE2) | ++ VC4_SET_FIELD(6, DSI1_PHY_AFEC0_IDR_DLANE3)); ++ ++ if (dsi->lanes < 4) ++ afec0 |= DSI1_PHY_AFEC0_PD_DLANE3; ++ if (dsi->lanes < 3) ++ afec0 |= DSI1_PHY_AFEC0_PD_DLANE2; ++ if (dsi->lanes < 2) ++ afec0 |= DSI1_PHY_AFEC0_PD_DLANE1; ++ ++ afec0 |= DSI1_PHY_AFEC0_RESET; ++ ++ DSI_PORT_WRITE(PHY_AFEC0, afec0); ++ ++ DSI_PORT_WRITE(PHY_AFEC1, 0); ++ ++ /* AFEC reset hold time */ ++ mdelay(1); ++ } ++ ++ ret = clk_prepare_enable(dsi->escape_clock); ++ if (ret) { ++ DRM_ERROR("Failed to turn on DSI escape clock: %d\n", ret); ++ return; ++ } ++ ++ ret = clk_prepare_enable(dsi->pll_phy_clock); ++ if (ret) { ++ DRM_ERROR("Failed to turn on DSI PLL: %d\n", ret); ++ return; ++ } ++ ++ hs_clock = clk_get_rate(dsi->pll_phy_clock); ++ ++ /* Yes, we set the DSI0P/DSI1P pixel clock to the byte rate, ++ * not the pixel clock rate. DSIxP take from the APHY's byte, ++ * DDR2, or DDR4 clock (we use byte) and feed into the PV at ++ * that rate. Separately, a value derived from PIX_CLK_DIV ++ * and HS_CLKC is fed into the PV to divide down to the actual ++ * pixel clock for pushing pixels into DSI. ++ */ ++ dsip_clock = phy_clock / 8; ++ ret = clk_set_rate(dsi->pixel_clock, dsip_clock); ++ if (ret) { ++ dev_err(dev, "Failed to set pixel clock to %ldHz: %d\n", ++ dsip_clock, ret); ++ } ++ ++ ret = clk_prepare_enable(dsi->pixel_clock); ++ if (ret) { ++ DRM_ERROR("Failed to turn on DSI pixel clock: %d\n", ret); ++ return; ++ } ++ ++ /* How many ns one DSI unit interval is. Note that the clock ++ * is DDR, so there's an extra divide by 2. ++ */ ++ ui_ns = DIV_ROUND_UP(500000000, hs_clock); ++ ++ DSI_PORT_WRITE(HS_CLT0, ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 262, 0), ++ DSI_HS_CLT0_CZERO) | ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 0, 8), ++ DSI_HS_CLT0_CPRE) | ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 38, 0), ++ DSI_HS_CLT0_CPREP)); ++ ++ DSI_PORT_WRITE(HS_CLT1, ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 0), ++ DSI_HS_CLT1_CTRAIL) | ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 60, 52), ++ DSI_HS_CLT1_CPOST)); ++ ++ DSI_PORT_WRITE(HS_CLT2, ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000000, 0), ++ DSI_HS_CLT2_WUP)); ++ ++ DSI_PORT_WRITE(HS_DLT3, ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 100, 0), ++ DSI_HS_DLT3_EXIT) | ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 105, 6), ++ DSI_HS_DLT3_ZERO) | ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, 40, 4), ++ DSI_HS_DLT3_PRE)); ++ ++ DSI_PORT_WRITE(HS_DLT4, ++ VC4_SET_FIELD(dsi_hs_timing(ui_ns, lpx * ESC_TIME_NS, 0), ++ DSI_HS_DLT4_LPX) | ++ VC4_SET_FIELD(max(dsi_hs_timing(ui_ns, 0, 8), ++ dsi_hs_timing(ui_ns, 60, 4)), ++ DSI_HS_DLT4_TRAIL) | ++ VC4_SET_FIELD(0, DSI_HS_DLT4_ANLAT)); ++ ++ DSI_PORT_WRITE(HS_DLT5, VC4_SET_FIELD(dsi_hs_timing(ui_ns, 1000, 5000), ++ DSI_HS_DLT5_INIT)); ++ ++ DSI_PORT_WRITE(HS_DLT6, ++ VC4_SET_FIELD(lpx * 5, DSI_HS_DLT6_TA_GET) | ++ VC4_SET_FIELD(lpx, DSI_HS_DLT6_TA_SURE) | ++ VC4_SET_FIELD(lpx * 4, DSI_HS_DLT6_TA_GO) | ++ VC4_SET_FIELD(lpx, DSI_HS_DLT6_LP_LPX)); ++ ++ DSI_PORT_WRITE(HS_DLT7, ++ VC4_SET_FIELD(dsi_esc_timing(1000000), ++ DSI_HS_DLT7_LP_WUP)); ++ ++ DSI_PORT_WRITE(PHYC, ++ DSI_PHYC_DLANE0_ENABLE | ++ (dsi->lanes >= 2 ? DSI_PHYC_DLANE1_ENABLE : 0) | ++ (dsi->lanes >= 3 ? DSI_PHYC_DLANE2_ENABLE : 0) | ++ (dsi->lanes >= 4 ? DSI_PHYC_DLANE3_ENABLE : 0) | ++ DSI_PORT_BIT(PHYC_CLANE_ENABLE) | ++ ((dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) ? ++ 0 : DSI_PORT_BIT(PHYC_HS_CLK_CONTINUOUS)) | ++ (dsi->port == 0 ? ++ VC4_SET_FIELD(lpx - 1, DSI0_PHYC_ESC_CLK_LPDT) : ++ VC4_SET_FIELD(lpx - 1, DSI1_PHYC_ESC_CLK_LPDT))); ++ ++ DSI_PORT_WRITE(CTRL, ++ DSI_PORT_READ(CTRL) | ++ DSI_CTRL_CAL_BYTE); ++ ++ /* HS timeout in HS clock cycles: disabled. */ ++ DSI_PORT_WRITE(HSTX_TO_CNT, 0); ++ /* LP receive timeout in HS clocks. */ ++ DSI_PORT_WRITE(LPRX_TO_CNT, 0xffffff); ++ /* Bus turnaround timeout */ ++ DSI_PORT_WRITE(TA_TO_CNT, 100000); ++ /* Display reset sequence timeout */ ++ DSI_PORT_WRITE(PR_TO_CNT, 100000); ++ ++ if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) { ++ DSI_PORT_WRITE(DISP0_CTRL, ++ VC4_SET_FIELD(divider, DSI_DISP0_PIX_CLK_DIV) | ++ VC4_SET_FIELD(format, DSI_DISP0_PFORMAT) | ++ VC4_SET_FIELD(DSI_DISP0_LP_STOP_PERFRAME, ++ DSI_DISP0_LP_STOP_CTRL) | ++ DSI_DISP0_ST_END | ++ DSI_DISP0_ENABLE); ++ } else { ++ DSI_PORT_WRITE(DISP0_CTRL, ++ DSI_DISP0_COMMAND_MODE | ++ DSI_DISP0_ENABLE); ++ } ++ ++ /* Set up DISP1 for transferring long command payloads through ++ * the pixfifo. ++ */ ++ DSI_PORT_WRITE(DISP1_CTRL, ++ VC4_SET_FIELD(DSI_DISP1_PFORMAT_32BIT_LE, ++ DSI_DISP1_PFORMAT) | ++ DSI_DISP1_ENABLE); ++ ++ /* Ungate the block. */ ++ if (dsi->port == 0) ++ DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI0_CTRL_CTRL0); ++ else ++ DSI_PORT_WRITE(CTRL, DSI_PORT_READ(CTRL) | DSI1_CTRL_EN); ++ ++ /* Bring AFE out of reset. */ ++ if (dsi->port == 0) { ++ } else { ++ DSI_PORT_WRITE(PHY_AFEC0, ++ DSI_PORT_READ(PHY_AFEC0) & ++ ~DSI1_PHY_AFEC0_RESET); ++ } ++ ++ vc4_dsi_ulps(dsi, false); ++ ++ if (debug_dump_regs) { ++ DRM_INFO("DSI regs after:\n"); ++ vc4_dsi_dump_regs(dsi); ++ } ++ ++ ret = drm_panel_enable(dsi->panel); ++ if (ret) { ++ DRM_ERROR("Panel failed to enable\n"); ++ drm_panel_unprepare(dsi->panel); ++ return; ++ } ++} ++ ++static ssize_t vc4_dsi_host_transfer(struct mipi_dsi_host *host, ++ const struct mipi_dsi_msg *msg) ++{ ++ struct vc4_dsi *dsi = host_to_dsi(host); ++ struct mipi_dsi_packet packet; ++ u32 pkth = 0, pktc = 0; ++ int i, ret; ++ bool is_long = mipi_dsi_packet_format_is_long(msg->type); ++ u32 cmd_fifo_len = 0, pix_fifo_len = 0; ++ ++ mipi_dsi_create_packet(&packet, msg); ++ ++ pkth |= VC4_SET_FIELD(packet.header[0], DSI_TXPKT1H_BC_DT); ++ pkth |= VC4_SET_FIELD(packet.header[1] | ++ (packet.header[2] << 8), ++ DSI_TXPKT1H_BC_PARAM); ++ if (is_long) { ++ /* Divide data across the various FIFOs we have available. ++ * The command FIFO takes byte-oriented data, but is of ++ * limited size. The pixel FIFO (never actually used for ++ * pixel data in reality) is word oriented, and substantially ++ * larger. So, we use the pixel FIFO for most of the data, ++ * sending the residual bytes in the command FIFO at the start. ++ * ++ * With this arrangement, the command FIFO will never get full. ++ */ ++ if (packet.payload_length <= 16) { ++ cmd_fifo_len = packet.payload_length; ++ pix_fifo_len = 0; ++ } else { ++ cmd_fifo_len = (packet.payload_length % ++ DSI_PIX_FIFO_WIDTH); ++ pix_fifo_len = ((packet.payload_length - cmd_fifo_len) / ++ DSI_PIX_FIFO_WIDTH); ++ } ++ ++ WARN_ON_ONCE(pix_fifo_len >= DSI_PIX_FIFO_DEPTH); ++ ++ pkth |= VC4_SET_FIELD(cmd_fifo_len, DSI_TXPKT1H_BC_CMDFIFO); ++ } ++ ++ if (msg->rx_len) { ++ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_RX, ++ DSI_TXPKT1C_CMD_CTRL); ++ } else { ++ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_CMD_CTRL_TX, ++ DSI_TXPKT1C_CMD_CTRL); ++ } ++ ++ for (i = 0; i < cmd_fifo_len; i++) ++ DSI_PORT_WRITE(TXPKT_CMD_FIFO, packet.payload[i]); ++ for (i = 0; i < pix_fifo_len; i++) { ++ const u8 *pix = packet.payload + cmd_fifo_len + i * 4; ++ ++ DSI_PORT_WRITE(TXPKT_PIX_FIFO, ++ pix[0] | ++ pix[1] << 8 | ++ pix[2] << 16 | ++ pix[3] << 24); ++ } ++ ++ if (msg->flags & MIPI_DSI_MSG_USE_LPM) ++ pktc |= DSI_TXPKT1C_CMD_MODE_LP; ++ if (is_long) ++ pktc |= DSI_TXPKT1C_CMD_TYPE_LONG; ++ ++ /* Send one copy of the packet. Larger repeats are used for pixel ++ * data in command mode. ++ */ ++ pktc |= VC4_SET_FIELD(1, DSI_TXPKT1C_CMD_REPEAT); ++ ++ pktc |= DSI_TXPKT1C_CMD_EN; ++ if (pix_fifo_len) { ++ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SECONDARY, ++ DSI_TXPKT1C_DISPLAY_NO); ++ } else { ++ pktc |= VC4_SET_FIELD(DSI_TXPKT1C_DISPLAY_NO_SHORT, ++ DSI_TXPKT1C_DISPLAY_NO); ++ } ++ ++ /* Enable the appropriate interrupt for the transfer completion. */ ++ dsi->xfer_result = 0; ++ reinit_completion(&dsi->xfer_completion); ++ DSI_PORT_WRITE(INT_STAT, DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF); ++ if (msg->rx_len) { ++ DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED | ++ DSI1_INT_PHY_DIR_RTF)); ++ } else { ++ DSI_PORT_WRITE(INT_EN, (DSI1_INTERRUPTS_ALWAYS_ENABLED | ++ DSI1_INT_TXPKT1_DONE)); ++ } ++ ++ /* Send the packet. */ ++ DSI_PORT_WRITE(TXPKT1H, pkth); ++ DSI_PORT_WRITE(TXPKT1C, pktc); ++ ++ if (!wait_for_completion_timeout(&dsi->xfer_completion, ++ msecs_to_jiffies(1000))) { ++ dev_err(&dsi->pdev->dev, "transfer interrupt wait timeout"); ++ dev_err(&dsi->pdev->dev, "instat: 0x%08x\n", ++ DSI_PORT_READ(INT_STAT)); ++ ret = -ETIMEDOUT; ++ } else { ++ ret = dsi->xfer_result; ++ } ++ ++ DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED); ++ ++ if (ret) ++ goto reset_fifo_and_return; ++ ++ if (ret == 0 && msg->rx_len) { ++ u32 rxpkt1h = DSI_PORT_READ(RXPKT1H); ++ u8 *msg_rx = msg->rx_buf; ++ ++ if (rxpkt1h & DSI_RXPKT1H_PKT_TYPE_LONG) { ++ u32 rxlen = VC4_GET_FIELD(rxpkt1h, ++ DSI_RXPKT1H_BC_PARAM); ++ ++ if (rxlen != msg->rx_len) { ++ DRM_ERROR("DSI returned %db, expecting %db\n", ++ rxlen, (int)msg->rx_len); ++ ret = -ENXIO; ++ goto reset_fifo_and_return; ++ } ++ ++ for (i = 0; i < msg->rx_len; i++) ++ msg_rx[i] = DSI_READ(DSI1_RXPKT_FIFO); ++ } else { ++ /* FINISHME: Handle AWER */ ++ ++ msg_rx[0] = VC4_GET_FIELD(rxpkt1h, ++ DSI_RXPKT1H_SHORT_0); ++ if (msg->rx_len > 1) { ++ msg_rx[1] = VC4_GET_FIELD(rxpkt1h, ++ DSI_RXPKT1H_SHORT_1); ++ } ++ } ++ } ++ ++ return ret; ++ ++reset_fifo_and_return: ++ DRM_ERROR("DSI transfer failed, resetting: %d\n", ret); ++ ++ DSI_PORT_WRITE(TXPKT1C, DSI_PORT_READ(TXPKT1C) & ~DSI_TXPKT1C_CMD_EN); ++ udelay(1); ++ DSI_PORT_WRITE(CTRL, ++ DSI_PORT_READ(CTRL) | ++ DSI_PORT_BIT(CTRL_RESET_FIFOS)); ++ ++ DSI_PORT_WRITE(TXPKT1C, 0); ++ DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED); ++ return ret; ++} ++ ++static int vc4_dsi_host_attach(struct mipi_dsi_host *host, ++ struct mipi_dsi_device *device) ++{ ++ struct vc4_dsi *dsi = host_to_dsi(host); ++ int ret = 0; ++ ++ dsi->lanes = device->lanes; ++ dsi->channel = device->channel; ++ dsi->format = device->format; ++ dsi->mode_flags = device->mode_flags; ++ ++ if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) { ++ dev_err(&dsi->pdev->dev, ++ "Only VIDEO mode panels supported currently.\n"); ++ return 0; ++ } ++ ++ dsi->panel = of_drm_find_panel(device->dev.of_node); ++ if (!dsi->panel) ++ return 0; ++ ++ ret = drm_panel_attach(dsi->panel, dsi->connector); ++ if (ret != 0) ++ return ret; ++ ++ drm_helper_hpd_irq_event(dsi->connector->dev); ++ ++ return 0; ++} ++ ++static int vc4_dsi_host_detach(struct mipi_dsi_host *host, ++ struct mipi_dsi_device *device) ++{ ++ struct vc4_dsi *dsi = host_to_dsi(host); ++ ++ if (dsi->panel) { ++ int ret = drm_panel_detach(dsi->panel); ++ ++ if (ret) ++ return ret; ++ ++ dsi->panel = NULL; ++ ++ drm_helper_hpd_irq_event(dsi->connector->dev); ++ } ++ ++ return 0; ++} ++ ++static const struct mipi_dsi_host_ops vc4_dsi_host_ops = { ++ .attach = vc4_dsi_host_attach, ++ .detach = vc4_dsi_host_detach, ++ .transfer = vc4_dsi_host_transfer, ++}; ++ ++static const struct drm_encoder_helper_funcs vc4_dsi_encoder_helper_funcs = { ++ .disable = vc4_dsi_encoder_disable, ++ .enable = vc4_dsi_encoder_enable, ++}; ++ ++static const struct of_device_id vc4_dsi_dt_match[] = { ++ { .compatible = "brcm,bcm2835-dsi1", (void *)(uintptr_t)1 }, ++ {} ++}; ++ ++static void dsi_handle_error(struct vc4_dsi *dsi, ++ irqreturn_t *ret, u32 stat, u32 bit, ++ const char *type) ++{ ++ if (!(stat & bit)) ++ return; ++ ++ DRM_ERROR("DSI%d: %s error\n", dsi->port, type); ++ *ret = IRQ_HANDLED; ++} ++ ++static irqreturn_t vc4_dsi_irq_handler(int irq, void *data) ++{ ++ struct vc4_dsi *dsi = data; ++ u32 stat = DSI_PORT_READ(INT_STAT); ++ irqreturn_t ret = IRQ_NONE; ++ ++ DSI_PORT_WRITE(INT_STAT, stat); ++ ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_ERR_SYNC_ESC, "LPDT sync"); ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_ERR_CONTROL, "data lane 0 sequence"); ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_ERR_CONT_LP0, "LP0 contention"); ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_ERR_CONT_LP1, "LP1 contention"); ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_HSTX_TO, "HSTX timeout"); ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_LPRX_TO, "LPRX timeout"); ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_TA_TO, "turnaround timeout"); ++ dsi_handle_error(dsi, &ret, stat, ++ DSI1_INT_PR_TO, "peripheral reset timeout"); ++ ++ if (stat & (DSI1_INT_TXPKT1_DONE | DSI1_INT_PHY_DIR_RTF)) { ++ complete(&dsi->xfer_completion); ++ ret = IRQ_HANDLED; ++ } else if (stat & DSI1_INT_HSTX_TO) { ++ complete(&dsi->xfer_completion); ++ dsi->xfer_result = -ETIMEDOUT; ++ ret = IRQ_HANDLED; ++ } ++ ++ return ret; ++} ++ ++/** ++ * Exposes clocks generated by the analog PHY that are consumed by ++ * CPRMAN (clk-bcm2835.c). ++ */ ++static int ++vc4_dsi_init_phy_clocks(struct vc4_dsi *dsi) ++{ ++ struct device *dev = &dsi->pdev->dev; ++ const char *parent_name = __clk_get_name(dsi->pll_phy_clock); ++ static const struct { ++ const char *dsi0_name, *dsi1_name; ++ int div; ++ } phy_clocks[] = { ++ { "dsi0_byte", "dsi1_byte", 8 }, ++ { "dsi0_ddr2", "dsi1_ddr2", 4 }, ++ { "dsi0_ddr", "dsi1_ddr", 2 }, ++ }; ++ int i; ++ ++ dsi->clk_onecell.clk_num = ARRAY_SIZE(phy_clocks); ++ dsi->clk_onecell.clks = devm_kcalloc(dev, ++ dsi->clk_onecell.clk_num, ++ sizeof(*dsi->clk_onecell.clks), ++ GFP_KERNEL); ++ if (!dsi->clk_onecell.clks) ++ return -ENOMEM; ++ ++ for (i = 0; i < ARRAY_SIZE(phy_clocks); i++) { ++ struct clk_fixed_factor *fix = &dsi->phy_clocks[i]; ++ struct clk_init_data init; ++ struct clk *clk; ++ ++ /* We just use core fixed factor clock ops for the PHY ++ * clocks. The clocks are actually gated by the ++ * PHY_AFEC0_DDRCLK_EN bits, which we should be ++ * setting if we use the DDR/DDR2 clocks. However, ++ * vc4_dsi_encoder_enable() is setting up both AFEC0, ++ * setting both our parent DSI PLL's rate and this ++ * clock's rate, so it knows if DDR/DDR2 are going to ++ * be used and could enable the gates itself. ++ */ ++ fix->mult = 1; ++ fix->div = phy_clocks[i].div; ++ fix->hw.init = &init; ++ ++ memset(&init, 0, sizeof(init)); ++ init.parent_names = &parent_name; ++ init.num_parents = 1; ++ if (dsi->port == 1) ++ init.name = phy_clocks[i].dsi1_name; ++ else ++ init.name = phy_clocks[i].dsi0_name; ++ init.ops = &clk_fixed_factor_ops; ++ init.flags = CLK_IS_BASIC; ++ ++ clk = devm_clk_register(dev, &fix->hw); ++ if (IS_ERR(clk)) ++ return PTR_ERR(clk); ++ ++ dsi->clk_onecell.clks[i] = clk; ++ } ++ ++ return of_clk_add_provider(dev->of_node, ++ of_clk_src_onecell_get, ++ &dsi->clk_onecell); ++} ++ ++static int vc4_dsi_bind(struct device *dev, struct device *master, void *data) ++{ ++ struct platform_device *pdev = to_platform_device(dev); ++ struct drm_device *drm = dev_get_drvdata(master); ++ struct vc4_dev *vc4 = to_vc4_dev(drm); ++ struct vc4_dsi *dsi; ++ struct vc4_dsi_encoder *vc4_dsi_encoder; ++ const struct of_device_id *match; ++ dma_cap_mask_t dma_mask; ++ int ret; ++ ++ dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); ++ if (!dsi) ++ return -ENOMEM; ++ ++ match = of_match_device(vc4_dsi_dt_match, dev); ++ if (!match) ++ return -ENODEV; ++ ++ dsi->port = (uintptr_t)match->data; ++ ++ vc4_dsi_encoder = devm_kzalloc(dev, sizeof(*vc4_dsi_encoder), ++ GFP_KERNEL); ++ if (!vc4_dsi_encoder) ++ return -ENOMEM; ++ vc4_dsi_encoder->base.type = VC4_ENCODER_TYPE_DSI1; ++ vc4_dsi_encoder->dsi = dsi; ++ dsi->encoder = &vc4_dsi_encoder->base.base; ++ ++ dsi->pdev = pdev; ++ dsi->regs = vc4_ioremap_regs(pdev, 0); ++ if (IS_ERR(dsi->regs)) ++ return PTR_ERR(dsi->regs); ++ ++ if (DSI_PORT_READ(ID) != DSI_ID_VALUE) { ++ dev_err(dev, "Port returned 0x%08x for ID instead of 0x%08x\n", ++ DSI_PORT_READ(ID), DSI_ID_VALUE); ++ return -ENODEV; ++ } ++ ++ /* DSI1 has a broken AXI slave that doesn't respond to writes ++ * from the ARM. It does handle writes from the DMA engine, ++ * so set up a channel for talking to it. ++ */ ++ if (dsi->port == 1) { ++ dsi->reg_dma_mem = dma_alloc_coherent(dev, 4, ++ &dsi->reg_dma_paddr, ++ GFP_KERNEL); ++ if (!dsi->reg_dma_mem) { ++ DRM_ERROR("Failed to get DMA memory\n"); ++ return -ENOMEM; ++ } ++ ++ dma_cap_zero(dma_mask); ++ dma_cap_set(DMA_MEMCPY, dma_mask); ++ dsi->reg_dma_chan = dma_request_chan_by_mask(&dma_mask); ++ if (IS_ERR(dsi->reg_dma_chan)) { ++ ret = PTR_ERR(dsi->reg_dma_chan); ++ if (ret != -EPROBE_DEFER) ++ DRM_ERROR("Failed to get DMA channel: %d\n", ++ ret); ++ return ret; ++ } ++ ++ /* Get the physical address of the device's registers. The ++ * struct resource for the regs gives us the bus address ++ * instead. ++ */ ++ dsi->reg_paddr = be32_to_cpup(of_get_address(dev->of_node, ++ 0, NULL, NULL)); ++ } ++ ++ init_completion(&dsi->xfer_completion); ++ /* At startup enable error-reporting interrupts and nothing else. */ ++ DSI_PORT_WRITE(INT_EN, DSI1_INTERRUPTS_ALWAYS_ENABLED); ++ /* Clear any existing interrupt state. */ ++ DSI_PORT_WRITE(INT_STAT, DSI_PORT_READ(INT_STAT)); ++ ++ ret = devm_request_irq(dev, platform_get_irq(pdev, 0), ++ vc4_dsi_irq_handler, 0, "vc4 dsi", dsi); ++ if (ret) { ++ if (ret != -EPROBE_DEFER) ++ dev_err(dev, "Failed to get interrupt: %d\n", ret); ++ return ret; ++ } ++ ++ dsi->escape_clock = devm_clk_get(dev, "escape"); ++ if (IS_ERR(dsi->escape_clock)) { ++ ret = PTR_ERR(dsi->escape_clock); ++ if (ret != -EPROBE_DEFER) ++ dev_err(dev, "Failed to get escape clock: %d\n", ret); ++ return ret; ++ } ++ ++ dsi->pll_phy_clock = devm_clk_get(dev, "phy"); ++ if (IS_ERR(dsi->pll_phy_clock)) { ++ ret = PTR_ERR(dsi->pll_phy_clock); ++ if (ret != -EPROBE_DEFER) ++ dev_err(dev, "Failed to get phy clock: %d\n", ret); ++ return ret; ++ } ++ ++ dsi->pixel_clock = devm_clk_get(dev, "pixel"); ++ if (IS_ERR(dsi->pixel_clock)) { ++ ret = PTR_ERR(dsi->pixel_clock); ++ if (ret != -EPROBE_DEFER) ++ dev_err(dev, "Failed to get pixel clock: %d\n", ret); ++ return ret; ++ } ++ ++ /* The esc clock rate is supposed to always be 100Mhz. */ ++ ret = clk_set_rate(dsi->escape_clock, 100 * 1000000); ++ if (ret) { ++ dev_err(dev, "Failed to set esc clock: %d\n", ret); ++ return ret; ++ } ++ ++ ret = vc4_dsi_init_phy_clocks(dsi); ++ if (ret) ++ return ret; ++ ++ if (dsi->port == 1) ++ vc4->dsi1 = dsi; ++ ++ drm_encoder_init(drm, dsi->encoder, &vc4_dsi_encoder_funcs, ++ DRM_MODE_ENCODER_DSI, NULL); ++ drm_encoder_helper_add(dsi->encoder, &vc4_dsi_encoder_helper_funcs); ++ ++ dsi->connector = vc4_dsi_connector_init(drm, dsi); ++ if (IS_ERR(dsi->connector)) { ++ ret = PTR_ERR(dsi->connector); ++ goto err_destroy_encoder; ++ } ++ ++ dsi->dsi_host.ops = &vc4_dsi_host_ops; ++ dsi->dsi_host.dev = dev; ++ ++ mipi_dsi_host_register(&dsi->dsi_host); ++ ++ dev_set_drvdata(dev, dsi); ++ ++ pm_runtime_enable(dev); ++ ++ return 0; ++ ++err_destroy_encoder: ++ vc4_dsi_encoder_destroy(dsi->encoder); ++ ++ return ret; ++} ++ ++static void vc4_dsi_unbind(struct device *dev, struct device *master, ++ void *data) ++{ ++ struct drm_device *drm = dev_get_drvdata(master); ++ struct vc4_dev *vc4 = to_vc4_dev(drm); ++ struct vc4_dsi *dsi = dev_get_drvdata(dev); ++ ++ pm_runtime_disable(dev); ++ ++ vc4_dsi_connector_destroy(dsi->connector); ++ vc4_dsi_encoder_destroy(dsi->encoder); ++ ++ mipi_dsi_host_unregister(&dsi->dsi_host); ++ ++ clk_disable_unprepare(dsi->pll_phy_clock); ++ clk_disable_unprepare(dsi->escape_clock); ++ ++ if (dsi->port == 1) ++ vc4->dsi1 = NULL; ++} ++ ++static const struct component_ops vc4_dsi_ops = { ++ .bind = vc4_dsi_bind, ++ .unbind = vc4_dsi_unbind, ++}; ++ ++static int vc4_dsi_dev_probe(struct platform_device *pdev) ++{ ++ return component_add(&pdev->dev, &vc4_dsi_ops); ++} ++ ++static int vc4_dsi_dev_remove(struct platform_device *pdev) ++{ ++ component_del(&pdev->dev, &vc4_dsi_ops); ++ return 0; ++} ++ ++struct platform_driver vc4_dsi_driver = { ++ .probe = vc4_dsi_dev_probe, ++ .remove = vc4_dsi_dev_remove, ++ .driver = { ++ .name = "vc4_dsi", ++ .of_match_table = vc4_dsi_dt_match, ++ }, ++}; |