diff options
Diffstat (limited to 'target/linux/generic-2.6')
5 files changed, 332 insertions, 0 deletions
diff --git a/target/linux/generic-2.6/config-2.6.23 b/target/linux/generic-2.6/config-2.6.23 index d6d982e..baac771 100644 --- a/target/linux/generic-2.6/config-2.6.23 +++ b/target/linux/generic-2.6/config-2.6.23 @@ -5,6 +5,7 @@ # CONFIG_ACORN_PARTITION is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_ADFS_FS is not set +# CONFIG_ADM6996_PHY is not set # CONFIG_AFFS_FS is not set # CONFIG_AFS_FS is not set # CONFIG_AF_RXRPC is not set diff --git a/target/linux/generic-2.6/files/drivers/net/phy/adm6996.c b/target/linux/generic-2.6/files/drivers/net/phy/adm6996.c new file mode 100644 index 0000000..3033813 --- /dev/null +++ b/target/linux/generic-2.6/files/drivers/net/phy/adm6996.c @@ -0,0 +1,170 @@ +/* + * ADM6996 switch driver + * + * Copyright (c) 2008 Felix Fietkau <nbd@openwrt.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License v2 as published by the + * Free Software Foundation + */ +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/errno.h> +#include <linux/unistd.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/spinlock.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/mii.h> +#include <linux/ethtool.h> +#include <linux/phy.h> + +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/uaccess.h> +#include "adm6996.h" + +MODULE_DESCRIPTION("Infineon ADM6996 Switch"); +MODULE_AUTHOR("Felix Fietkau"); +MODULE_LICENSE("GPL"); + +struct adm6996_priv { + /* use abstraction for regops, we want to add gpio support in the future */ + u16 (*read)(struct phy_device *phydev, enum admreg reg); + void (*write)(struct phy_device *phydev, enum admreg reg, u16 val); +}; + +#define to_adm(_phy) ((struct adm6996_priv *) (_phy)->priv) + + +static inline u16 +r16(struct phy_device *pdev, enum admreg reg) +{ + return to_adm(pdev)->read(pdev, reg); +} + +static inline void +w16(struct phy_device *pdev, enum admreg reg, u16 val) +{ + to_adm(pdev)->write(pdev, reg, val); +} + + +static u16 +adm6996_read_mii_reg(struct phy_device *phydev, enum admreg reg) +{ + return phydev->bus->read(phydev->bus, PHYADDR(reg)); +} + +static void +adm6996_write_mii_reg(struct phy_device *phydev, enum admreg reg, u16 val) +{ + phydev->bus->write(phydev->bus, PHYADDR(reg), val); +} + + +static int adm6996_config_init(struct phy_device *pdev) +{ + int i; + + printk("%s: ADM6996 PHY driver attached.\n", pdev->attached_dev->name); + pdev->supported = ADVERTISED_100baseT_Full; + pdev->advertising = ADVERTISED_100baseT_Full; + + /* initialize port and vlan settings */ + for (i = 0; i < ADM_PHY_PORTS; i++) { + w16(pdev, adm_portcfg[i], ADM_PORTCFG_INIT | + ADM_PORTCFG_PVID((i == ADM_WAN_PORT) ? 1 : 0)); + } + w16(pdev, adm_portcfg[5], ADM_PORTCFG_CPU); + + /* reset all ports */ + for (i = 0; i < ADM_PHY_PORTS; i++) { + w16(pdev, ADM_PHY_PORT(i), ADM_PHYCFG_INIT); + } + + return 0; +} + +static int adm6996_read_status(struct phy_device *phydev) +{ + phydev->speed = SPEED_100; + phydev->duplex = DUPLEX_FULL; + phydev->state = PHY_UP; + return 0; +} + +static int adm6996_config_aneg(struct phy_device *phydev) +{ + return 0; +} + +static int adm6996_probe(struct phy_device *pdev) +{ + struct adm6996_priv *priv; + + priv = kzalloc(sizeof(struct adm6996_priv), GFP_KERNEL); + if (priv == NULL) + return -ENOMEM; + + priv->read = adm6996_read_mii_reg; + priv->write = adm6996_write_mii_reg; + pdev->priv = priv; + return 0; +} + +static void adm6996_remove(struct phy_device *pdev) +{ + kfree(pdev->priv); +} + +static bool adm6996_detect(struct mii_bus *bus, int addr) +{ + u16 reg; + + /* we only attach to phy id 0 */ + if (addr != 0) + return false; + + /* look for the switch on the bus */ + reg = bus->read(bus, PHYADDR(ADM_SIG0)) & ADM_SIG0_MASK; + if (reg != ADM_SIG0_VAL) + return false; + + reg = bus->read(bus, PHYADDR(ADM_SIG1)) & ADM_SIG1_MASK; + if (reg != ADM_SIG1_VAL) + return false; + + return true; +} + +static struct phy_driver adm6996_driver = { + .name = "Infineon ADM6996", + .features = PHY_BASIC_FEATURES, + .detect = adm6996_detect, + .probe = adm6996_probe, + .remove = adm6996_remove, + .config_init = &adm6996_config_init, + .config_aneg = &adm6996_config_aneg, + .read_status = &adm6996_read_status, + .driver = { .owner = THIS_MODULE,}, +}; + +static int __init adm6996_init(void) +{ + return phy_driver_register(&adm6996_driver); +} + +static void __exit adm6996_exit(void) +{ + phy_driver_unregister(&adm6996_driver); +} + +module_init(adm6996_init); +module_exit(adm6996_exit); diff --git a/target/linux/generic-2.6/files/drivers/net/phy/adm6996.h b/target/linux/generic-2.6/files/drivers/net/phy/adm6996.h new file mode 100644 index 0000000..e074901 --- /dev/null +++ b/target/linux/generic-2.6/files/drivers/net/phy/adm6996.h @@ -0,0 +1,105 @@ +/* + * ADM6996 switch driver + * + * Copyright (c) 2008 Felix Fietkau <nbd@openwrt.org> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License v2 as published by the + * Free Software Foundation + */ +#ifndef __ADM6996_H +#define __ADM6996_H + +#define ADM_PHY_PORTS 5 +#define ADM_CPU_PORT 5 +#define ADM_WAN_PORT 0 /* FIXME: dynamic ? */ + +enum admreg { + ADM_EEPROM_BASE = 0x0, + ADM_P0_CFG = ADM_EEPROM_BASE + 1, + ADM_P1_CFG = ADM_EEPROM_BASE + 3, + ADM_P2_CFG = ADM_EEPROM_BASE + 5, + ADM_P3_CFG = ADM_EEPROM_BASE + 7, + ADM_P4_CFG = ADM_EEPROM_BASE + 8, + ADM_P5_CFG = ADM_EEPROM_BASE + 9, + ADM_EEPROM_EXT_BASE = 0x40, + ADM_COUNTER_BASE = 0xa0, + ADM_SIG0 = ADM_COUNTER_BASE + 0, + ADM_SIG1 = ADM_COUNTER_BASE + 1, + ADM_PHY_BASE = 0x200, +#define ADM_PHY_PORT(n) (ADM_PHY_BASE + (0x20 * n)) +}; + +/* Chip identification patterns */ +#define ADM_SIG0_MASK 0xfff0 +#define ADM_SIG0_VAL 0x1020 +#define ADM_SIG1_MASK 0xffff +#define ADM_SIG1_VAL 0x0007 + +enum { + ADM_PHYCFG_COLTST = (1 << 7), /* Enable collision test */ + ADM_PHYCFG_DPLX = (1 << 8), /* Enable full duplex */ + ADM_PHYCFG_ANEN_RST = (1 << 9), /* Restart auto negotiation (self clear) */ + ADM_PHYCFG_ISO = (1 << 10), /* Isolate PHY */ + ADM_PHYCFG_PDN = (1 << 11), /* Power down PHY */ + ADM_PHYCFG_ANEN = (1 << 12), /* Enable auto negotiation */ + ADM_PHYCFG_SPEED_100 = (1 << 13), /* Enable 100 Mbit/s */ + ADM_PHYCFG_LPBK = (1 << 14), /* Enable loopback operation */ + ADM_PHYCFG_RST = (1 << 15), /* Reset the port (self clear) */ + ADM_PHYCFG_INIT = ( + ADM_PHYCFG_RST | + ADM_PHYCFG_SPEED_100 | + ADM_PHYCFG_ANEN | + ADM_PHYCFG_ANEN_RST + ) +}; + +enum { + ADM_PORTCFG_FC = (1 << 0), /* Enable 802.x flow control */ + ADM_PORTCFG_AN = (1 << 1), /* Enable auto-negotiation */ + ADM_PORTCFG_SPEED_100 = (1 << 2), /* Enable 100 Mbit/s */ + ADM_PORTCFG_DPLX = (1 << 3), /* Enable full duplex */ + ADM_PORTCFG_OT = (1 << 4), /* Output tagged packets */ + ADM_PORTCFG_PD = (1 << 5), /* Port disable */ + ADM_PORTCFG_TV_PRIO = (1 << 6), /* 0 = VLAN based priority + * 1 = TOS based priority */ + ADM_PORTCFG_PPE = (1 << 7), /* Port based priority enable */ + ADM_PORTCFG_PP_S = (1 << 8), /* Port based priority, 2 bits */ + ADM_PORTCFG_PVID_BASE = (1 << 10), /* Primary VLAN id, 4 bits */ + ADM_PORTCFG_FSE = (1 << 14), /* Fx select enable */ + ADM_PORTCFG_CAM = (1 << 15), /* Crossover Auto MDIX */ + + ADM_PORTCFG_INIT = ( + ADM_PORTCFG_FC | + ADM_PORTCFG_AN | + ADM_PORTCFG_SPEED_100 | + ADM_PORTCFG_DPLX | + ADM_PORTCFG_CAM + ), + ADM_PORTCFG_CPU = ( + ADM_PORTCFG_FC | + ADM_PORTCFG_SPEED_100 | + ADM_PORTCFG_OT | + ADM_PORTCFG_DPLX + ), +}; + +#define ADM_PORTCFG_PPID(N) ((n & 0x3) << 8) +#define ADM_PORTCFG_PVID(n) ((n & 0xf) << 10) + +static const u8 adm_portcfg[] = { + [0] = ADM_P0_CFG, + [1] = ADM_P1_CFG, + [2] = ADM_P2_CFG, + [3] = ADM_P3_CFG, + [4] = ADM_P4_CFG, + [5] = ADM_P5_CFG, +}; + +/* + * Split the register address in phy id and register + * it will get combined again by the mdio bus op + */ +#define PHYADDR(_reg) ((_reg >> 5) & 0xff), (_reg & 0x1f) + +#endif diff --git a/target/linux/generic-2.6/patches-2.6.23/610-phy_detect.patch b/target/linux/generic-2.6/patches-2.6.23/610-phy_detect.patch new file mode 100644 index 0000000..394cd37 --- /dev/null +++ b/target/linux/generic-2.6/patches-2.6.23/610-phy_detect.patch @@ -0,0 +1,30 @@ +Index: linux-2.6.23.16/drivers/net/phy/mdio_bus.c +=================================================================== +--- linux-2.6.23.16.orig/drivers/net/phy/mdio_bus.c 2008-02-11 07:06:32.000000000 +0100 ++++ linux-2.6.23.16/drivers/net/phy/mdio_bus.c 2008-04-20 01:55:46.000000000 +0200 +@@ -131,6 +131,9 @@ + struct phy_device *phydev = to_phy_device(dev); + struct phy_driver *phydrv = to_phy_driver(drv); + ++ if (phydrv->detect) ++ return (phydrv->detect(phydev->bus, phydev->addr)); ++ + return ((phydrv->phy_id & phydrv->phy_id_mask) == + (phydev->phy_id & phydrv->phy_id_mask)); + } +Index: linux-2.6.23.16/include/linux/phy.h +=================================================================== +--- linux-2.6.23.16.orig/include/linux/phy.h 2008-04-20 00:36:18.000000000 +0200 ++++ linux-2.6.23.16/include/linux/phy.h 2008-04-20 01:55:04.000000000 +0200 +@@ -319,6 +319,11 @@ + u32 features; + u32 flags; + ++ /* Called during discovery to test if the ++ * device can attach to the bus, even if ++ * phy id and mask do not match */ ++ bool (*detect)(struct mii_bus *bus, int addr); ++ + /* Called to initialize the PHY, + * including after a reset */ + int (*config_init)(struct phy_device *phydev); diff --git a/target/linux/generic-2.6/patches-2.6.23/620-phy_adm6996.patch b/target/linux/generic-2.6/patches-2.6.23/620-phy_adm6996.patch new file mode 100644 index 0000000..2997392 --- /dev/null +++ b/target/linux/generic-2.6/patches-2.6.23/620-phy_adm6996.patch @@ -0,0 +1,26 @@ +Index: linux-2.6.23.16/drivers/net/phy/Kconfig +=================================================================== +--- linux-2.6.23.16.orig/drivers/net/phy/Kconfig 2008-04-20 04:40:22.000000000 +0200 ++++ linux-2.6.23.16/drivers/net/phy/Kconfig 2008-04-20 04:40:32.000000000 +0200 +@@ -60,6 +60,11 @@ + ---help--- + Currently supports the IP175C PHY. + ++config ADM6996_PHY ++ tristate "Driver for ADM6996 switches" ++ ---help--- ++ Currently supports the ADM6996F switch ++ + config FIXED_PHY + tristate "Drivers for PHY emulation on fixed speed/link" + ---help--- +Index: linux-2.6.23.16/drivers/net/phy/Makefile +=================================================================== +--- linux-2.6.23.16.orig/drivers/net/phy/Makefile 2008-04-20 04:40:22.000000000 +0200 ++++ linux-2.6.23.16/drivers/net/phy/Makefile 2008-04-20 04:40:32.000000000 +0200 +@@ -12,4 +12,5 @@ + obj-$(CONFIG_VITESSE_PHY) += vitesse.o + obj-$(CONFIG_BROADCOM_PHY) += broadcom.o + obj-$(CONFIG_ICPLUS_PHY) += icplus.o ++obj-$(CONFIG_ADM6996_PHY) += adm6996.o + obj-$(CONFIG_FIXED_PHY) += fixed.o |