diff options
Diffstat (limited to 'target/linux/ipq40xx')
10 files changed, 462 insertions, 1 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index fcba2ae..475a862 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -34,6 +34,11 @@ netgear,ex6150v2) meraki,mr33) ucidef_set_interface_lan "eth0" ;; +zyxel,nbg6617) + ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2G" "phy0tpt" + ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:green:wlan5G" "phy1tpt" + ucidef_set_led_usbport "usb" "USB" "${board}:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" + ;; zyxel,wre6606) ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy0tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy1tpt" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 03e0c0e..5c90ef1 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -48,6 +48,11 @@ netgear,ex6150v2 |\ zyxel,wre6606) ucidef_set_interface_lan "eth0" ;; +zyxel,nbg6617) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" + ;; *) echo "Unsupported hardware. Network interfaces not intialized" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index d89ddf6..1d4fd9c 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -146,6 +146,7 @@ case "$FIRMWARE" in openmesh,a62) ath10kcal_extract "0:ART" 4096 12064 ;; + zyxel,nbg6617 |\ zyxel,wre6606) ath10kcal_extract "ART" 4096 12064 ath10kcal_patch_mac_crc $(macaddr_add $(cat /sys/class/net/eth0/address) -2) @@ -181,6 +182,7 @@ case "$FIRMWARE" in openmesh,a62) ath10kcal_extract "0:ART" 20480 12064 ;; + zyxel,nbg6617 |\ zyxel,wre6606) ath10kcal_extract "ART" 20480 12064 ath10kcal_patch_mac_crc $(macaddr_add $(cat /sys/class/net/eth0/address) -1) diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh index 1acd736..44e81ca 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh @@ -8,6 +8,10 @@ preinit_set_mac_address() { mac_lan=$(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) [ -n "$mac_lan" ] && ip link set dev eth0 address "$mac_lan" ;; + zyxel,nbg6617) + base_mac=$(cat /sys/class/net/eth0/address) + ip link set dev eth0 address $(macaddr_add "$base_mac" +2) + ip link set dev eth1 address $(macaddr_add "$base_mac" +3) esac } diff --git a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh new file mode 100644 index 0000000..578ddbe --- /dev/null +++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh @@ -0,0 +1,19 @@ +#!/bin/sh + +set_preinit_iface() { + . /lib/functions.sh + + case $(board_name) in + asus,rt-ac58u| \ + avm,fritzbox-4040| \ + glinet,gl-b1300| \ + meraki,mr33| \ + zyxel,nbg6617) + ifname=eth0 + ;; + *) + ;; + esac +} + +boot_hook_add preinit_main set_preinit_iface diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 4096e12..0e29302 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -29,6 +29,21 @@ EOF return 0; } +zyxel_do_upgrade() { + local tar_file="$1" + + local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$') + board_dir=${board_dir%/} + + tar Oxf $tar_file ${board_dir}/kernel | mtd write - kernel + + if [ "$SAVE_CONFIG" -eq 1 ]; then + tar Oxf $tar_file ${board_dir}/root | mtd -j "$CONF_TAR" write - rootfs + else + tar Oxf $tar_file ${board_dir}/root | mtd write - rootfs + fi +} + platform_do_upgrade() { case "$(board_name)" in 8dev,jalapeno) @@ -48,6 +63,9 @@ platform_do_upgrade() { CI_KERNPART="part.safe" nand_do_upgrade "$1" ;; + zyxel,nbg6617) + zyxel_do_upgrade "$1" + ;; *) default_do_upgrade "$ARGV" ;; diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-nbg6617.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-nbg6617.dts new file mode 100644 index 0000000..d7f8c59 --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-nbg6617.dts @@ -0,0 +1,321 @@ +/* Copyright (c) 2015, The Linux Foundation. All rights reserved. + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + * + */ + +#include "qcom-ipq4019.dtsi" +#include "qcom-ipq4019-bus.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/input/linux-event-codes.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "ZyXEL NBG6617"; + compatible = "zyxel,nbg6617", "qcom,ipq4019"; + + chosen { + /* + * the vendor u-boot adds root and mtdparts cmdline parameters + * which we don't want... but we have to overwrite them or else + * the kernel will take them at face value. + */ + bootargs-append = " mtdparts= root=31:13"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + soc { + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2@60f8800 { + status = "okay"; + }; + + serial@78af000 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + wlan { + label = "wlan"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + linux,code = <KEY_RFKILL>; + linux,input-type = <EV_SW>; + }; + + wps { + label = "wps"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + + reset { + label = "reset"; + gpios = <&tlmm 4 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + power: power { + label = "nbg6617:green:power"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + }; + + usb { + label = "nbg6617:green:usb"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + }; + + wlan2G { + label = "nbg6617:green:wlan2G"; + gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>; + }; + + wlan5G { + label = "nbg6617:green:wlan5G"; + gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>; + }; + + wps { + label = "nbg6617:green:wps"; + gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + spi_0_pins: spi_0_pinmux { + mux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54"; + drive-strength = <2>; + bias-disable; + output-low; + }; + }; + led_pins: led_pinmux { + mux { + pins = "gpio0", "gpio1", "gpio3", "gpio5", "gpio58"; + drive-strength = <0x8>; + bias-disable; + output-low; + }; + }; +}; + +&spi_0 { /* BLSP1 QUP1 */ + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + mx25l25635f@0 { + compatible = "mx25l25635f", "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + spi-max-frequency = <24000000>; + status = "okay"; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition0@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition1@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + partition2@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + partition3@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + partition4@d0000 { + label = "DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + partition5@e0000 { + label = "APPSBL"; /* u-boot */ + reg = <0x000e0000 0x00080000>; + /* U-Boot Standalone App "zloader" is located at 0x64000 */ + read-only; + }; + partition6@160000 { + label = "APPSBLENV"; /* u-boot env */ + reg = <0x00160000 0x00010000>; + }; + partition7@170000 { + /* make a backup of this partition! */ + label = "ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + partition8@180000 { + label = "kernel"; + reg = <0x00180000 0x00400000>; + }; + partition9@580000 { + label = "dualflag"; + reg = <0x00580000 0x00010000>; + read-only; + }; + partition10@590000 { + label = "header"; + reg = <0x00590000 0x00010000>; + }; + partition11@5a0000 { + label = "romd"; + reg = <0x005a0000 0x00100000>; + read-only; + }; + partition12@6a0000 { + label = "not_root_data"; + /* + * for some strange reason, someone at ZyXEL + * had the "great" idea to put the rootfs_data + * in front of rootfs... Don't do that! + * As a result this one, full MebiByte remains + * unused. + */ + reg = <0x006a0000 0x00100000>; + }; + partition13@7a0000 { + label = "rootfs"; + reg = <0x007a0000 0x01860000>; + }; + }; + }; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&wifi0 { + status = "okay"; +}; + +&wifi1 { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 38600cf..d1ee100 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -1,6 +1,8 @@ include $(TOPDIR)/rules.mk include $(INCLUDE_DIR)/image.mk +DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION + define Device/Default PROFILES := Default KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts) @@ -205,6 +207,26 @@ define Device/qcom_ap-dk04.1-c1 endef TARGET_DEVICES += qcom_ap-dk04.1-c1 +define Device/zyxel_nbg6617 + $(call Device/FitImageLzma) + DEVICE_DTS := qcom-ipq4018-nbg6617 + DEVICE_TITLE := ZyXEL NBG6617 + ROOTFS_SIZE := 24960k + RAS_BOARD := NBG6617 + RAS_ROOTFS_SIZE := 19840k + RAS_VERSION := "$(VERSION_DIST) $(REVISION)" + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + IMAGES := sysupgrade.bin factory.bin +# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is +# at least as large as the one of the initial firmware image (not the current +# one on the device). This only applies to the Web-UI, the bootlaoder ignores +# this minimum-size. However, the larger image can be flashed both ways. + IMAGE/factory.bin := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | make-ras + IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata + DEVICE_PACKAGES := ipq-wifi-zyxel_nbg6617 uboot-envtools +endef +TARGET_DEVICES += zyxel_nbg6617 + define Device/zyxel_wre6606 $(call Device/FitImage) DEVICE_TITLE := ZyXEL WRE6606 diff --git a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch index 3aa368b..8066f98 100644 --- a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,19 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,20 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -19,6 +19,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4018-ex6150v2.dtb \ + qcom-ipq4018-fritz4040.dtb \ + qcom-ipq4018-jalapeno.dtb \ ++ qcom-ipq4018-nbg6617.dtb \ + qcom-ipq4018-rt-ac58u.dtb \ + qcom-ipq4018-wre6606.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ diff --git a/target/linux/ipq40xx/patches-4.14/303-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch b/target/linux/ipq40xx/patches-4.14/303-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch new file mode 100644 index 0000000..7c513a6 --- /dev/null +++ b/target/linux/ipq40xx/patches-4.14/303-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch @@ -0,0 +1,64 @@ +Index: linux-4.14.50/drivers/mtd/spi-nor/spi-nor.c +=================================================================== +--- linux-4.14.50.orig/drivers/mtd/spi-nor/spi-nor.c ++++ linux-4.14.50/drivers/mtd/spi-nor/spi-nor.c +@@ -1025,6 +1025,7 @@ static const struct flash_info spi_nor_i + { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) }, + { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, + { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, ++ { "mx25l25635f", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, + { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) }, + { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) }, + { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, +@@ -1189,11 +1190,12 @@ static const struct flash_info spi_nor_i + { }, + }; + +-static const struct flash_info *spi_nor_read_id(struct spi_nor *nor) ++static const struct flash_info *spi_nor_read_id(struct spi_nor *nor, ++ const char *name) + { + int tmp; + u8 id[SPI_NOR_MAX_ID_LEN]; +- const struct flash_info *info; ++ const struct flash_info *info, *first_match = NULL; + + tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN); + if (tmp < 0) { +@@ -1204,10 +1206,16 @@ static const struct flash_info *spi_nor_ + for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) { + info = &spi_nor_ids[tmp]; + if (info->id_len) { +- if (!memcmp(info->id, id, info->id_len)) +- return &spi_nor_ids[tmp]; ++ if (!memcmp(info->id, id, info->id_len)) { ++ if (!name || !strcmp(name, info->name)) ++ return info; ++ if (!first_match) ++ first_match = info; ++ } + } + } ++ if (first_match) ++ return first_match; + dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n", + id[0], id[1], id[2]); + return ERR_PTR(-ENODEV); +@@ -2667,7 +2675,7 @@ int spi_nor_scan(struct spi_nor *nor, co + info = spi_nor_match_id(name); + /* Try to auto-detect if chip name wasn't specified or not found */ + if (!info) +- info = spi_nor_read_id(nor); ++ info = spi_nor_read_id(nor, NULL); + if (IS_ERR_OR_NULL(info)) + return -ENOENT; + +@@ -2678,7 +2686,7 @@ int spi_nor_scan(struct spi_nor *nor, co + if (name && info->id_len) { + const struct flash_info *jinfo; + +- jinfo = spi_nor_read_id(nor); ++ jinfo = spi_nor_read_id(nor, name); + if (IS_ERR(jinfo)) { + return PTR_ERR(jinfo); + } else if (jinfo != info) { |