diff options
Diffstat (limited to 'target/linux/ipq806x/patches-3.18/301-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch')
-rw-r--r-- | target/linux/ipq806x/patches-3.18/301-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch | 367 |
1 files changed, 367 insertions, 0 deletions
diff --git a/target/linux/ipq806x/patches-3.18/301-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch b/target/linux/ipq806x/patches-3.18/301-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch new file mode 100644 index 0000000..abd7cf6 --- /dev/null +++ b/target/linux/ipq806x/patches-3.18/301-ARM-qcom-add-Netgear-Nighthawk-X4-R7500-device-tree.patch @@ -0,0 +1,367 @@ +From 7e77aa188a7a7c4391856a9e5ef5ef58f769e679 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 9 Aug 2015 13:02:38 +0200 +Subject: [PATCH] ARM: qcom: add Netgear Nighthawk X4 R7500 device tree + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/arm/boot/dts/Makefile | 1 + + arch/arm/boot/dts/qcom-ipq8064-r7500.dts | 370 +++++++++++++++++++++++++++++++ + 2 files changed, 371 insertions(+) + create mode 100644 arch/arm/boot/dts/qcom-ipq8064-r7500.dts + +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -361,6 +361,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ + qcom-apq8084-mtp.dtb \ + qcom-ipq8064-ap148.dtb \ + qcom-ipq8064-db149.dtb \ ++ qcom-ipq8064-r7500.dtb \ + qcom-msm8660-surf.dtb \ + qcom-msm8960-cdp.dtb \ + qcom-msm8974-sony-xperia-honami.dtb +--- /dev/null ++++ b/arch/arm/boot/dts/qcom-ipq8064-r7500.dts +@@ -0,0 +1,342 @@ ++#include "qcom-ipq8064-v1.0.dtsi" ++ ++#include <dt-bindings/input/input.h> ++ ++/ { ++ model = "Netgear Nighthawk X4 R7500"; ++ compatible = "netgear,r7500", "qcom,ipq8064"; ++ ++ memory@0 { ++ reg = <0x42000000 0xe000000>; ++ device_type = "memory"; ++ }; ++ ++ reserved-memory { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges; ++ rsvd@41200000 { ++ reg = <0x41200000 0x300000>; ++ no-map; ++ }; ++ }; ++ ++ aliases { ++ serial0 = &uart4; ++ mdio-gpio0 = &mdio0; ++ }; ++ ++ chosen { ++ bootargs = "rootfstype=squashfs noinitrd"; ++ linux,stdout-path = "serial0:115200n8"; ++ }; ++ ++ soc { ++ pinmux@800000 { ++ i2c4_pins: i2c4_pinmux { ++ pins = "gpio12", "gpio13"; ++ function = "gsbi4"; ++ bias-disable; ++ }; ++ ++ nand_pins: nand_pins { ++ mux { ++ pins = "gpio34", "gpio35", "gpio36", ++ "gpio37", "gpio38", "gpio39", ++ "gpio40", "gpio41", "gpio42", ++ "gpio43", "gpio44", "gpio45", ++ "gpio46", "gpio47"; ++ function = "nand"; ++ drive-strength = <10>; ++ bias-disable; ++ }; ++ pullups { ++ pins = "gpio39"; ++ bias-pull-up; ++ }; ++ hold { ++ pins = "gpio40", "gpio41", "gpio42", ++ "gpio43", "gpio44", "gpio45", ++ "gpio46", "gpio47"; ++ bias-bus-hold; ++ }; ++ }; ++ ++ mdio0_pins: mdio0_pins { ++ mux { ++ pins = "gpio0", "gpio1"; ++ function = "gpio"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; ++ ++ rgmii2_pins: rgmii2_pins { ++ mux { ++ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", ++ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; ++ function = "rgmii2"; ++ drive-strength = <8>; ++ bias-disable; ++ }; ++ }; ++ }; ++ ++ gsbi@16300000 { ++ qcom,mode = <GSBI_PROT_I2C_UART>; ++ status = "ok"; ++ serial@16340000 { ++ status = "ok"; ++ }; ++ /* ++ * The i2c device on gsbi4 should not be enabled. ++ * On ipq806x designs gsbi4 i2c is meant for exclusive ++ * RPM usage. Turning this on in kernel manifests as ++ * i2c failure for the RPM. ++ */ ++ }; ++ ++ sata-phy@1b400000 { ++ status = "ok"; ++ }; ++ ++ sata@29000000 { ++ status = "ok"; ++ }; ++ ++ phy@100f8800 { /* USB3 port 1 HS phy */ ++ status = "ok"; ++ }; ++ ++ phy@100f8830 { /* USB3 port 1 SS phy */ ++ status = "ok"; ++ }; ++ ++ phy@110f8800 { /* USB3 port 0 HS phy */ ++ status = "ok"; ++ }; ++ ++ phy@110f8830 { /* USB3 port 0 SS phy */ ++ status = "ok"; ++ }; ++ ++ usb30@0 { ++ status = "ok"; ++ }; ++ ++ usb30@1 { ++ status = "ok"; ++ }; ++ ++ pcie0: pci@1b500000 { ++ status = "ok"; ++ }; ++ ++ pcie1: pci@1b700000 { ++ status = "ok"; ++ }; ++ ++ nand@1ac00000 { ++ status = "ok"; ++ ++ pinctrl-0 = <&nand_pins>; ++ pinctrl-names = "default"; ++ ++ nand-ecc-strength = <4>; ++ nand-bus-width = <8>; ++ ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ qcadata@0 { ++ label = "qcadata"; ++ reg = <0x0000000 0x0c80000>; ++ read-only; ++ }; ++ ++ APPSBL@c80000 { ++ label = "APPSBL"; ++ reg = <0x0c80000 0x0500000>; ++ read-only; ++ }; ++ ++ APPSBLENV@1180000 { ++ label = "APPSBLENV"; ++ reg = <0x1180000 0x0080000>; ++ read-only; ++ }; ++ ++ art: art@1200000 { ++ label = "art"; ++ reg = <0x1200000 0x0140000>; ++ read-only; ++ }; ++ ++ kernel@1340000 { ++ label = "kernel"; ++ reg = <0x1340000 0x0200000>; ++ }; ++ ++ ubi@1540000 { ++ label = "ubi"; ++ reg = <0x1540000 0x1800000>; ++ }; ++ ++ netgear@2d40000 { ++ label = "netgear"; ++ reg = <0x2d40000 0x0c00000>; ++ read-only; ++ }; ++ ++ reserve@3940000 { ++ label = "reserve"; ++ reg = <0x3940000 0x46c0000>; ++ read-only; ++ }; ++ ++ firmware@1340000 { ++ label = "firmware"; ++ reg = <0x1340000 0x1a00000>; ++ }; ++ ++ }; ++ ++ mdio0: mdio { ++ compatible = "virtual,mdio-gpio"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; ++ pinctrl-0 = <&mdio0_pins>; ++ pinctrl-names = "default"; ++ ++ phy0: ethernet-phy@0 { ++ device_type = "ethernet-phy"; ++ reg = <0>; ++ qca,ar8327-initvals = < ++ 0x00004 0x7600000 /* PAD0_MODE */ ++ 0x00008 0x1000000 /* PAD5_MODE */ ++ 0x0000c 0x80 /* PAD6_MODE */ ++ 0x000e4 0xaa545 /* MAC_POWER_SEL */ ++ 0x000e0 0xc74164de /* SGMII_CTRL */ ++ 0x0007c 0x4e /* PORT0_STATUS */ ++ 0x00094 0x4e /* PORT6_STATUS */ ++ >; ++ }; ++ ++ phy4: ethernet-phy@4 { ++ device_type = "ethernet-phy"; ++ reg = <4>; ++ }; ++ }; ++ ++ gmac1: ethernet@37200000 { ++ status = "ok"; ++ phy-mode = "rgmii"; ++ qcom,id = <1>; ++ ++ pinctrl-0 = <&rgmii2_pins>; ++ pinctrl-names = "default"; ++ ++ mtd-mac-address = <&art 6>; ++ ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ ++ gmac2: ethernet@37400000 { ++ status = "ok"; ++ phy-mode = "sgmii"; ++ qcom,id = <2>; ++ ++ mtd-mac-address = <&art 0>; ++ ++ fixed-link { ++ speed = <1000>; ++ full-duplex; ++ }; ++ }; ++ }; ++ ++ gpio-keys { ++ compatible = "gpio-keys"; ++ ++ wifi { ++ label = "wifi"; ++ gpios = <&qcom_pinmux 6 1>; ++ linux,code = <KEY_WLAN>; ++ }; ++ ++ reset { ++ label = "reset"; ++ gpios = <&qcom_pinmux 54 1>; ++ linux,code = <KEY_RESTART>; ++ }; ++ ++ wps { ++ label = "wps"; ++ gpios = <&qcom_pinmux 65 1>; ++ linux,code = <KEY_WPS_BUTTON>; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ ++ usb1 { ++ label = "r7500:amber:usb1"; ++ gpios = <&qcom_pinmux 7 0>; ++ }; ++ ++ usb3 { ++ label = "r7500:amber:usb3"; ++ gpios = <&qcom_pinmux 8 0>; ++ }; ++ ++ status { ++ label = "r7500:amber:status"; ++ gpios = <&qcom_pinmux 9 0>; ++ }; ++ ++ internet { ++ label = "r7500:white:internet"; ++ gpios = <&qcom_pinmux 22 0>; ++ }; ++ ++ wan { ++ label = "r7500:white:wan"; ++ gpios = <&qcom_pinmux 23 0>; ++ }; ++ ++ wps { ++ label = "r7500:white:wps"; ++ gpios = <&qcom_pinmux 24 0>; ++ }; ++ ++ esata { ++ label = "r7500:white:esata"; ++ gpios = <&qcom_pinmux 26 0>; ++ }; ++ ++ power { ++ label = "r7500:white:power"; ++ gpios = <&qcom_pinmux 53 0>; ++ default-state = "on"; ++ }; ++ ++ rfkill { ++ label = "r7500:white:rfkill"; ++ gpios = <&qcom_pinmux 64 0>; ++ }; ++ ++ wifi5g { ++ label = "r7500:white:wifi5g"; ++ gpios = <&qcom_pinmux 67 0>; ++ }; ++ }; ++}; ++ ++&adm_dma { ++ status = "ok"; ++}; |