1 files changed, 0 insertions, 74 deletions
diff --git a/target/linux/ipq806x/patches-4.9/0005-arm-qcom-dts-Enable-NAND-node-on-IPQ8064-AP148-platf.patch b/target/linux/ipq806x/patches-4.9/0005-arm-qcom-dts-Enable-NAND-node-on-IPQ8064-AP148-platf.patch
deleted file mode 100644
index 2bfbf08..0000000
--- a/target/linux/ipq806x/patches-4.9/0005-arm-qcom-dts-Enable-NAND-node-on-IPQ8064-AP148-platf.patch
+++ /dev/null
@@ -1,74 +0,0 @@
-From f8d0939eca47f56449ec583810a6ff41a1caaa91 Mon Sep 17 00:00:00 2001
-From: Thomas Pedersen <twp@codeaurora.org>
-Date: Mon, 16 May 2016 17:58:54 -0700
-Subject: [PATCH 05/37] arm: qcom: dts: Enable NAND node on IPQ8064 AP148
- platform
-
-Original patch by Archit Taneja.
-
-Enable the NAND controller node on the AP148 platform. Provide pinmux
-information.
-
-Signed-off-by: Archit Taneja <architt@codeaurora.org>
-Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
----
- arch/arm/boot/dts/qcom-ipq8064-ap148.dts |   42 ++++++++++++++++++++++++++++++
- 1 file changed, 42 insertions(+)
-
---- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
-@@ -38,6 +38,28 @@
- 					bias-none;
- 				};
- 			};
-+			nand_pins: nand_pins {
-+				mux {
-+					pins = "gpio34", "gpio35", "gpio36",
-+					       "gpio37", "gpio38", "gpio39",
-+					       "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					function = "nand";
-+					drive-strength = <10>;
-+					bias-disable;
-+				};
-+				pullups {
-+					pins = "gpio39";
-+					bias-pull-up;
-+				};
-+				hold {
-+					pins = "gpio40", "gpio41", "gpio42",
-+					       "gpio43", "gpio44", "gpio45",
-+					       "gpio46", "gpio47";
-+					bias-bus-hold;
-+				};
-+			};
- 		};
- 
- 		gsbi@16300000 {
-@@ -98,5 +120,25 @@
- 			ports-implemented = <0x1>;
- 			status = "ok";
- 		};
-+
-+		nand@1ac00000 {
-+			status = "ok";
-+
-+			pinctrl-0 = <&nand_pins>;
-+			pinctrl-names = "default";
-+
-+			nandcs@0 {
-+				compatible = "qcom,nandcs";
-+				reg = <0>;
-+
-+				nand-ecc-strength = <4>;
-+				nand-ecc-step-size = <512>;
-+				nand-bus-width = <8>;
-+			};
-+		};
- 	};
- };
-+
-+&adm_dma {
-+	status = "ok";
-+};