diff options
Diffstat (limited to 'target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch')
-rw-r--r-- | target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch | 73 |
1 files changed, 0 insertions, 73 deletions
diff --git a/target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch b/target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch deleted file mode 100644 index 9c0d969..0000000 --- a/target/linux/sunxi/patches-3.18/202-dt-sun7i-add-bluetooth-to-cubietruck.patch +++ /dev/null @@ -1,73 +0,0 @@ -From c6e2b7dad39a7887f935458d1c8de84db06243e1 Mon Sep 17 00:00:00 2001 -From: Chen-Yu Tsai <wens@csie.org> -Date: Thu, 26 Dec 2013 17:15:47 +0800 -Subject: [PATCH] ARM: dts: sun7i: add bluetooth module to CubieTruck DTS - -The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The -Bluetooth part is a BCM20710 IC connected to UART2 in the A20 -SoC. The IC also takes a 32.768 KHz low power clock input, a power -enable signal and a wake signal via GPIO. - -The Bluetooth module supports out-of-band interrupt signaling via -GPIO, but this is not supported in this patch. ---- - arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 36 ++++++++++++++++++++++++++++++ - 1 file changed, 36 insertions(+) - ---- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts -+++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts -@@ -103,6 +103,20 @@ - allwinner,drive = <0>; - allwinner,pull = <0>; - }; -+ -+ bt_pwr_pin: bt_pwr_pin@0 { -+ allwinner,pins = "PH18"; -+ allwinner,function = "gpio_out"; -+ allwinner,drive = <0>; -+ allwinner,pull = <0>; -+ }; -+ -+ bt_wake_pin: bt_wake_pin@0 { -+ allwinner,pins = "PH24"; -+ allwinner,function = "gpio_out"; -+ allwinner,drive = <0>; -+ allwinner,pull = <0>; -+ }; - }; - - pwm: pwm@01c20e00 { -@@ -123,6 +137,12 @@ - status = "okay"; - }; - -+ uart2: serial@01c28800 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&uart2_pins_a>; -+ status = "okay"; -+ }; -+ - i2c0: i2c@01c2ac00 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins_a>; -@@ -214,4 +234,20 @@ - enable-active-high; - gpio = <&pio 7 9 0>; - }; -+ -+ rfkill-switches { -+ compatible = "simple-bus"; -+ pinctrl-names = "default"; -+ -+ rfkill_bt { -+ compatible = "rfkill-gpio"; -+ pinctrl-0 = <&bt_pwr_pin>, <&clk_out_a_pins_a>; -+ rfkill-name = "bt"; -+ rfkill-type = <2>; -+ bt_shutdown-gpios = <0>, <&pio 7 18 0>; /* PH18 */ -+ bt_reset-gpios = <&pio 7 24 0>; /* PH24 */ -+ clocks = <&clk_out_a>; -+ clock-frequency = <32768>; -+ }; -+ }; - }; |