diff options
Diffstat (limited to 'target/linux')
43 files changed, 9766 insertions, 1 deletions
diff --git a/target/linux/ixp4xx/Makefile b/target/linux/ixp4xx/Makefile index 780ca96..3f6110a 100644 --- a/target/linux/ixp4xx/Makefile +++ b/target/linux/ixp4xx/Makefile @@ -13,7 +13,7 @@ FEATURES:=squashfs MAINTAINER:=Imre Kaloz <kaloz@openwrt.org> SUBTARGETS=generic harddisk -KERNEL_PATCHVER:=3.10 +KERNEL_PATCHVER:=3.14 include $(INCLUDE_DIR)/target.mk diff --git a/target/linux/ixp4xx/config-3.14 b/target/linux/ixp4xx/config-3.14 new file mode 100644 index 0000000..3fcab85 --- /dev/null +++ b/target/linux/ixp4xx/config-3.14 @@ -0,0 +1,239 @@ +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_ARCH_ADI_COYOTE is not set +CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y +CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y +CONFIG_ARCH_HAS_DMA_SET_COHERENT_MASK=y +CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y +CONFIG_ARCH_IXCDP1100=y +CONFIG_ARCH_IXDP425=y +CONFIG_ARCH_IXDP4XX=y +CONFIG_ARCH_IXP4XX=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +# CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set +CONFIG_ARCH_NR_GPIO=0 +# CONFIG_ARCH_PRPMC1100 is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y +CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_USE_BUILTIN_BSWAP=y +CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y +CONFIG_ARCH_WANT_GENERAL_HUGETLB=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +CONFIG_ARM=y +# CONFIG_ARM_CPU_SUSPEND is not set +CONFIG_ARM_L1_CACHE_SHIFT=5 +CONFIG_ARM_NR_BANKS=8 +CONFIG_ARM_PATCH_PHYS_VIRT=y +# CONFIG_ARM_THUMB is not set +CONFIG_ATAGS=y +CONFIG_BOUNCE=y +# CONFIG_CACHE_L2X0 is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_CLKSRC_MMIO=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200" +CONFIG_CMDLINE_FROM_BOOTLOADER=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_BIG_ENDIAN=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_ENDIAN_BE32=y +# CONFIG_CPU_ENDIAN_BE8 is not set +CONFIG_CPU_IXP43X=y +CONFIG_CPU_IXP46X=y +CONFIG_CPU_PABRT_LEGACY=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_USE_DOMAINS=y +CONFIG_CPU_XSCALE=y +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_LL_INCLUDE="debug/8250.S" +CONFIG_DEBUG_UART_8250=y +# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set +CONFIG_DEBUG_UART_8250_SHIFT=2 +# CONFIG_DEBUG_UART_8250_WORD is not set +CONFIG_DEBUG_UART_PHYS=0xc8000003 +# CONFIG_DEBUG_UART_PL01X is not set +CONFIG_DEBUG_UART_VIRT=0xfef00003 +# CONFIG_DEBUG_USER is not set +CONFIG_DMABOUNCE=y +CONFIG_DNOTIFY=y +CONFIG_EEPROM_AT24=y +CONFIG_FRAME_POINTER=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IO=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_DEVRES=y +CONFIG_GPIO_GW_I2C_PLD=y +CONFIG_GPIO_SYSFS=y +# CONFIG_HAMRADIO is not set +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_PFN_VALID=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set +CONFIG_HAVE_BPF_JIT=y +CONFIG_HAVE_CC_STACKPROTECTOR=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DMA_ATTRS=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y +CONFIG_HAVE_KERNEL_GZIP=y +CONFIG_HAVE_KERNEL_LZ4=y +CONFIG_HAVE_KERNEL_LZMA=y +CONFIG_HAVE_KERNEL_LZO=y +CONFIG_HAVE_KERNEL_XZ=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_PERF_REGS=y +CONFIG_HAVE_PERF_USER_STACK_DUMP=y +CONFIG_HAVE_PROC_CPU=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HAVE_UID16=y +CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y +CONFIG_HWMON=y +CONFIG_HWMON_VID=y +CONFIG_HW_RANDOM=y +CONFIG_HW_RANDOM_IXP4XX=y +CONFIG_HZ_FIXED=0 +CONFIG_HZ_PERIODIC=y +CONFIG_I2C=y +CONFIG_I2C_ALGOBIT=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_GPIO=y +# CONFIG_I2C_IOP3XX is not set +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IOMMU_HELPER=y +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +# CONFIG_IWMMXT is not set +CONFIG_IXP4XX_ETH=y +# CONFIG_IXP4XX_INDIRECT_PCI is not set +CONFIG_IXP4XX_NPE=y +CONFIG_IXP4XX_QMGR=y +CONFIG_IXP4XX_WATCHDOG=y +CONFIG_KTIME_SCALAR=y +CONFIG_LEDS_FSG=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_LATCH=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +CONFIG_MACH_AP1000=y +CONFIG_MACH_AP42X=y +# CONFIG_MACH_ARCOM_VULCAN is not set +CONFIG_MACH_AVILA=y +CONFIG_MACH_CAMBRIA=y +CONFIG_MACH_COMPEXWP18=y +# CONFIG_MACH_DEVIXP is not set +CONFIG_MACH_DSMG600=y +CONFIG_MACH_FSG=y +CONFIG_MACH_GATEWAY7001=y +# CONFIG_MACH_GORAMO_MLR is not set +# CONFIG_MACH_GTWX5715 is not set +# CONFIG_MACH_IXDP465 is not set +CONFIG_MACH_IXDPG425=y +# CONFIG_MACH_KIXRP435 is not set +CONFIG_MACH_LOFT=y +CONFIG_MACH_MI424WR=y +# CONFIG_MACH_MIC256 is not set +# CONFIG_MACH_MICCPT is not set +CONFIG_MACH_NAS100D=y +CONFIG_MACH_NSLU2=y +CONFIG_MACH_PRONGHORN=y +CONFIG_MACH_PRONGHORNMETRO=y +CONFIG_MACH_SIDEWINDER=y +CONFIG_MACH_TW2662=y +CONFIG_MACH_TW5334=y +CONFIG_MACH_USR8200=y +CONFIG_MACH_WG302V1=y +CONFIG_MACH_WG302V2=y +CONFIG_MACH_WRT300NV2=y +CONFIG_MDIO_BOARDINFO=y +CONFIG_MIGHT_HAVE_PCI=y +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +# CONFIG_MTD_CFI_GEOMETRY is not set +CONFIG_MTD_IXP4XX=y +CONFIG_MTD_OTP=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_REDBOOT_PARTS=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_KUSER_HELPERS=y +CONFIG_NEED_MACH_IO_H=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NET_VENDOR_XSCALE=y +CONFIG_NO_BOOTMEM=y +CONFIG_OLD_SIGACTION=y +CONFIG_OLD_SIGSUSPEND3=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PCI=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PHYLIB=y +# CONFIG_PREEMPT_RCU is not set +# CONFIG_RCU_STALL_COMMON is not set +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_DS1672=y +CONFIG_RTC_DRV_ISL1208=y +CONFIG_RTC_DRV_PCF8563=y +CONFIG_RTC_DRV_X1205=y +CONFIG_SCHED_HRTICK=y +# CONFIG_SCSI_DMA is not set +CONFIG_SENSORS_AD7418=y +CONFIG_SENSORS_GSC=y +CONFIG_SENSORS_MAX6650=y +CONFIG_SENSORS_W83781D=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SPLIT_PTLOCK_CPUS=999999 +CONFIG_SWIOTLB=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_UID16=y +CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h" +CONFIG_USB_EHCI_BIG_ENDIAN_DESC=y +CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y +CONFIG_USB_SUPPORT=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_WATCHDOG_NOWAYOUT=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ZBOOT_ROM_TEXT=0x0 diff --git a/target/linux/ixp4xx/patches-3.14/001-arm-ixp4xx-set-cohorent_dma_mask-for-ethernet-platfo.patch b/target/linux/ixp4xx/patches-3.14/001-arm-ixp4xx-set-cohorent_dma_mask-for-ethernet-platfo.patch new file mode 100644 index 0000000..4f640d1 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/001-arm-ixp4xx-set-cohorent_dma_mask-for-ethernet-platfo.patch @@ -0,0 +1,136 @@ +From 7113f56b683c5123df5c20724ac813cee66fa21a Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Mon, 1 Jul 2013 16:49:05 +0200 +Subject: [PATCH 1/2] arm: ixp4xx: set cohorent_dma_mask for ethernet platform + devices + +ARM requires the cohorent_dma_mask set, so set it for the platform +devices so that the ethernet driver has access to it. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/arm/mach-ixp4xx/fsg-setup.c | 2 ++ + arch/arm/mach-ixp4xx/goramo_mlr.c | 2 ++ + arch/arm/mach-ixp4xx/ixdp425-setup.c | 3 +++ + arch/arm/mach-ixp4xx/nas100d-setup.c | 1 + + arch/arm/mach-ixp4xx/nslu2-setup.c | 1 + + arch/arm/mach-ixp4xx/omixp-setup.c | 3 +++ + arch/arm/mach-ixp4xx/vulcan-setup.c | 2 ++ + 7 files changed, 14 insertions(+) + +--- a/arch/arm/mach-ixp4xx/fsg-setup.c ++++ b/arch/arm/mach-ixp4xx/fsg-setup.c +@@ -142,12 +142,14 @@ static struct platform_device fsg_eth[] + .id = IXP4XX_ETH_NPEB, + .dev = { + .platform_data = fsg_plat_eth, ++ .coherent_dma_mask = DMA_BIT_MASK(32), + }, + }, { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEC, + .dev = { + .platform_data = fsg_plat_eth + 1, ++ .coherent_dma_mask = DMA_BIT_MASK(32), + }, + } + }; +--- a/arch/arm/mach-ixp4xx/goramo_mlr.c ++++ b/arch/arm/mach-ixp4xx/goramo_mlr.c +@@ -294,10 +294,12 @@ static struct platform_device device_eth + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev.platform_data = eth_plat, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + }, { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEC, + .dev.platform_data = eth_plat + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + } + }; + +--- a/arch/arm/mach-ixp4xx/ixdp425-setup.c ++++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c +@@ -20,6 +20,7 @@ + #include <linux/mtd/nand.h> + #include <linux/mtd/partitions.h> + #include <linux/delay.h> ++#include <linux/dma-mapping.h> + #include <linux/gpio.h> + #include <asm/types.h> + #include <asm/setup.h> +@@ -196,10 +197,12 @@ static struct platform_device ixdp425_et + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev.platform_data = ixdp425_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + }, { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEC, + .dev.platform_data = ixdp425_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + } + }; + +--- a/arch/arm/mach-ixp4xx/nas100d-setup.c ++++ b/arch/arm/mach-ixp4xx/nas100d-setup.c +@@ -170,6 +170,7 @@ static struct platform_device nas100d_et + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev.platform_data = nas100d_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + } + }; + +--- a/arch/arm/mach-ixp4xx/nslu2-setup.c ++++ b/arch/arm/mach-ixp4xx/nslu2-setup.c +@@ -182,6 +182,7 @@ static struct platform_device nslu2_eth[ + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev.platform_data = nslu2_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + } + }; + +--- a/arch/arm/mach-ixp4xx/omixp-setup.c ++++ b/arch/arm/mach-ixp4xx/omixp-setup.c +@@ -17,6 +17,7 @@ + #include <linux/serial_8250.h> + #include <linux/mtd/mtd.h> + #include <linux/mtd/partitions.h> ++#include <linux/dma-mapping.h> + #ifdef CONFIG_LEDS_CLASS + #include <linux/leds.h> + #endif +@@ -190,10 +191,12 @@ static struct platform_device ixdp425_et + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEB, + .dev.platform_data = ixdp425_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + }, { + .name = "ixp4xx_eth", + .id = IXP4XX_ETH_NPEC, + .dev.platform_data = ixdp425_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), + }, + }; + +--- a/arch/arm/mach-ixp4xx/vulcan-setup.c ++++ b/arch/arm/mach-ixp4xx/vulcan-setup.c +@@ -139,6 +139,7 @@ static struct platform_device vulcan_eth + .id = IXP4XX_ETH_NPEB, + .dev = { + .platform_data = &vulcan_plat_eth[0], ++ .coherent_dma_mask = DMA_BIT_MASK(32), + }, + }, + [1] = { +@@ -146,6 +147,7 @@ static struct platform_device vulcan_eth + .id = IXP4XX_ETH_NPEC, + .dev = { + .platform_data = &vulcan_plat_eth[1], ++ .coherent_dma_mask = DMA_BIT_MASK(32), + }, + }, + }; diff --git a/target/linux/ixp4xx/patches-3.14/002-ixp4xx_eth-use-parent-device-for-dma-allocations.patch b/target/linux/ixp4xx/patches-3.14/002-ixp4xx_eth-use-parent-device-for-dma-allocations.patch new file mode 100644 index 0000000..702d182 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/002-ixp4xx_eth-use-parent-device-for-dma-allocations.patch @@ -0,0 +1,95 @@ +From 1d67040af0144c549f4db8144d2ccc253ff8639c Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Mon, 1 Jul 2013 16:39:28 +0200 +Subject: [PATCH 2/2] net: ixp4xx_eth: use parent device for dma allocations + +Now that the platfomr device provides a dma_cohorent_mask, use it for +dma operations. + +This fixes ethernet on ixp4xx which was broken since 3.7. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + drivers/net/ethernet/xscale/ixp4xx_eth.c | 23 ++++++++++++----------- + 1 file changed, 12 insertions(+), 11 deletions(-) + +--- a/drivers/net/ethernet/xscale/ixp4xx_eth.c ++++ b/drivers/net/ethernet/xscale/ixp4xx_eth.c +@@ -661,10 +661,10 @@ static inline void queue_put_desc(unsign + static inline void dma_unmap_tx(struct port *port, struct desc *desc) + { + #ifdef __ARMEB__ +- dma_unmap_single(&port->netdev->dev, desc->data, ++ dma_unmap_single(port->netdev->dev.parent, desc->data, + desc->buf_len, DMA_TO_DEVICE); + #else +- dma_unmap_single(&port->netdev->dev, desc->data & ~3, ++ dma_unmap_single(port->netdev->dev.parent, desc->data & ~3, + ALIGN((desc->data & 3) + desc->buf_len, 4), + DMA_TO_DEVICE); + #endif +@@ -731,9 +731,9 @@ static int eth_poll(struct napi_struct * + + #ifdef __ARMEB__ + if ((skb = netdev_alloc_skb(dev, RX_BUFF_SIZE))) { +- phys = dma_map_single(&dev->dev, skb->data, ++ phys = dma_map_single(dev->dev.parent, skb->data, + RX_BUFF_SIZE, DMA_FROM_DEVICE); +- if (dma_mapping_error(&dev->dev, phys)) { ++ if (dma_mapping_error(dev->dev.parent, phys)) { + dev_kfree_skb(skb); + skb = NULL; + } +@@ -756,10 +756,11 @@ static int eth_poll(struct napi_struct * + #ifdef __ARMEB__ + temp = skb; + skb = port->rx_buff_tab[n]; +- dma_unmap_single(&dev->dev, desc->data - NET_IP_ALIGN, ++ dma_unmap_single(dev->dev.parent, desc->data - NET_IP_ALIGN, + RX_BUFF_SIZE, DMA_FROM_DEVICE); + #else +- dma_sync_single_for_cpu(&dev->dev, desc->data - NET_IP_ALIGN, ++ dma_sync_single_for_cpu(dev->dev.parent, ++ desc->data - NET_IP_ALIGN, + RX_BUFF_SIZE, DMA_FROM_DEVICE); + memcpy_swab32((u32 *)skb->data, (u32 *)port->rx_buff_tab[n], + ALIGN(NET_IP_ALIGN + desc->pkt_len, 4) / 4); +@@ -878,7 +879,7 @@ static int eth_xmit(struct sk_buff *skb, + memcpy_swab32(mem, (u32 *)((int)skb->data & ~3), bytes / 4); + #endif + +- phys = dma_map_single(&dev->dev, mem, bytes, DMA_TO_DEVICE); ++ phys = dma_map_single(dev->dev.parent, mem, bytes, DMA_TO_DEVICE); + if (dma_mapping_error(&dev->dev, phys)) { + dev_kfree_skb(skb); + #ifndef __ARMEB__ +@@ -1128,7 +1129,7 @@ static int init_queues(struct port *port + int i; + + if (!ports_open) { +- dma_pool = dma_pool_create(DRV_NAME, &port->netdev->dev, ++ dma_pool = dma_pool_create(DRV_NAME, port->netdev->dev.parent, + POOL_ALLOC_SIZE, 32, 0); + if (!dma_pool) + return -ENOMEM; +@@ -1156,9 +1157,9 @@ static int init_queues(struct port *port + data = buff; + #endif + desc->buf_len = MAX_MRU; +- desc->data = dma_map_single(&port->netdev->dev, data, ++ desc->data = dma_map_single(port->netdev->dev.parent, data, + RX_BUFF_SIZE, DMA_FROM_DEVICE); +- if (dma_mapping_error(&port->netdev->dev, desc->data)) { ++ if (dma_mapping_error(port->netdev->dev.parent, desc->data)) { + free_buffer(buff); + return -EIO; + } +@@ -1178,7 +1179,7 @@ static void destroy_queues(struct port * + struct desc *desc = rx_desc_ptr(port, i); + buffer_t *buff = port->rx_buff_tab[i]; + if (buff) { +- dma_unmap_single(&port->netdev->dev, ++ dma_unmap_single(port->netdev->dev.parent, + desc->data - NET_IP_ALIGN, + RX_BUFF_SIZE, DMA_FROM_DEVICE); + free_buffer(buff); diff --git a/target/linux/ixp4xx/patches-3.14/020-gateworks_i2c_pld.patch b/target/linux/ixp4xx/patches-3.14/020-gateworks_i2c_pld.patch new file mode 100644 index 0000000..a4b9a1f --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/020-gateworks_i2c_pld.patch @@ -0,0 +1,432 @@ +Index: linux-3.14.25/drivers/gpio/Kconfig +=================================================================== +--- linux-3.14.25.orig/drivers/gpio/Kconfig 2014-11-30 15:25:59.554663011 +0100 ++++ linux-3.14.25/drivers/gpio/Kconfig 2014-11-30 15:26:36.399907220 +0100 +@@ -722,6 +722,14 @@ + Support for the RDC R321x SoC GPIOs over southbridge + PCI configuration space. + ++config GPIO_GW_I2C_PLD ++ tristate "Gateworks I2C PLD GPIO Expander" ++ depends on I2C ++ help ++ Say yes here to provide access to the Gateworks I2C PLD GPIO ++ Expander. This is used at least on the GW2358-4. ++ ++ + comment "SPI GPIO expanders:" + + config GPIO_MAX7301 +Index: linux-3.14.25/drivers/gpio/Makefile +=================================================================== +--- linux-3.14.25.orig/drivers/gpio/Makefile 2014-11-30 15:25:59.554663011 +0100 ++++ linux-3.14.25/drivers/gpio/Makefile 2014-11-30 15:26:36.399907220 +0100 +@@ -99,3 +99,4 @@ + obj-$(CONFIG_GPIO_WM8994) += gpio-wm8994.o + obj-$(CONFIG_GPIO_XILINX) += gpio-xilinx.o + obj-$(CONFIG_GPIO_XTENSA) += gpio-xtensa.o ++obj-$(CONFIG_GPIO_GW_I2C_PLD) += gw_i2c_pld.o +Index: linux-3.14.25/drivers/gpio/gw_i2c_pld.c +=================================================================== +--- /dev/null 1970-01-01 00:00:00.000000000 +0000 ++++ linux-3.14.25/drivers/gpio/gw_i2c_pld.c 2014-12-01 07:15:30.030979315 +0100 +@@ -0,0 +1,374 @@ ++/* ++ * Gateworks I2C PLD GPIO expander ++ * ++ * Copyright (C) 2009 Gateworks Corporation ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/slab.h> ++#include <linux/hardirq.h> ++#include <linux/i2c.h> ++#include <linux/i2c/gw_i2c_pld.h> ++#include <linux/module.h> ++#include <linux/export.h> ++#include <asm/gpio.h> ++#include <mach/hardware.h> ++ ++static const struct i2c_device_id gw_i2c_pld_id[] = { ++ { "gw_i2c_pld", 8 }, ++ { } ++}; ++MODULE_DEVICE_TABLE(i2c, gw_i2c_pld_id); ++ ++/* ++ * The Gateworks I2C PLD chip only expose one read and one ++ * write register. Writing a "one" bit (to match the reset state) lets ++ * that pin be used as an input. It is an open-drain model. ++ */ ++ ++struct gw_i2c_pld { ++ struct gpio_chip chip; ++ struct i2c_client *client; ++ unsigned out; /* software latch */ ++}; ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* ++ * The Gateworks I2C PLD chip does not properly send the acknowledge bit ++ * thus we cannot use standard i2c_smbus functions. We have recreated ++ * our own here, but we still use the rt_mutex_lock to lock the i2c_bus ++ * as the device still exists on the I2C bus. ++*/ ++ ++#define PLD_SCL_GPIO 6 ++#define PLD_SDA_GPIO 7 ++ ++#define SCL_LO() gpio_line_set(PLD_SCL_GPIO, IXP4XX_GPIO_LOW) ++#define SCL_HI() gpio_line_set(PLD_SCL_GPIO, IXP4XX_GPIO_HIGH) ++#define SCL_EN() gpio_line_config(PLD_SCL_GPIO, IXP4XX_GPIO_OUT) ++#define SDA_LO() gpio_line_set(PLD_SDA_GPIO, IXP4XX_GPIO_LOW) ++#define SDA_HI() gpio_line_set(PLD_SDA_GPIO, IXP4XX_GPIO_HIGH) ++#define SDA_EN() gpio_line_config(PLD_SDA_GPIO, IXP4XX_GPIO_OUT) ++#define SDA_DIS() gpio_line_config(PLD_SDA_GPIO, IXP4XX_GPIO_IN) ++#define SDA_IN(x) gpio_line_get(PLD_SDA_GPIO, &x); ++ ++static int i2c_pld_write_byte(int address, int byte) ++{ ++ int i; ++ ++ address = (address << 1) & ~0x1; ++ ++ SDA_HI(); ++ SDA_EN(); ++ SCL_EN(); ++ SCL_HI(); ++ SDA_LO(); ++ SCL_LO(); ++ ++ for (i = 7; i >= 0; i--) ++ { ++ if (address & (1 << i)) ++ SDA_HI(); ++ else ++ SDA_LO(); ++ ++ SCL_HI(); ++ SCL_LO(); ++ } ++ ++ SDA_DIS(); ++ SCL_HI(); ++ SDA_IN(i); ++ SCL_LO(); ++ SDA_EN(); ++ ++ for (i = 7; i >= 0; i--) ++ { ++ if (byte & (1 << i)) ++ SDA_HI(); ++ else ++ SDA_LO(); ++ SCL_HI(); ++ SCL_LO(); ++ } ++ ++ SDA_DIS(); ++ SCL_HI(); ++ SDA_IN(i); ++ SCL_LO(); ++ ++ SDA_HI(); ++ SDA_EN(); ++ ++ SDA_LO(); ++ SCL_HI(); ++ SDA_HI(); ++ SCL_LO(); ++ SCL_HI(); ++ ++ return 0; ++} ++ ++static unsigned int i2c_pld_read_byte(int address) ++{ ++ int i = 0, byte = 0; ++ int bit; ++ ++ address = (address << 1) | 0x1; ++ ++ SDA_HI(); ++ SDA_EN(); ++ SCL_EN(); ++ SCL_HI(); ++ SDA_LO(); ++ SCL_LO(); ++ ++ for (i = 7; i >= 0; i--) ++ { ++ if (address & (1 << i)) ++ SDA_HI(); ++ else ++ SDA_LO(); ++ ++ SCL_HI(); ++ SCL_LO(); ++ } ++ ++ SDA_DIS(); ++ SCL_HI(); ++ SDA_IN(i); ++ SCL_LO(); ++ SDA_EN(); ++ ++ SDA_DIS(); ++ for (i = 7; i >= 0; i--) ++ { ++ SCL_HI(); ++ SDA_IN(bit); ++ byte |= bit << i; ++ SCL_LO(); ++ } ++ ++ SDA_LO(); ++ SCL_HI(); ++ SDA_HI(); ++ SCL_LO(); ++ SCL_HI(); ++ ++ return byte; ++} ++ ++ ++static int gw_i2c_pld_input8(struct gpio_chip *chip, unsigned offset) ++{ ++ int ret; ++ struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip); ++ struct i2c_adapter *adap = gpio->client->adapter; ++ ++ if (in_atomic() || irqs_disabled()) { ++ ret = rt_mutex_trylock(&adap->bus_lock); ++ if (!ret) ++ /* I2C activity is ongoing. */ ++ return -EAGAIN; ++ } else { ++ rt_mutex_lock(&adap->bus_lock); ++ } ++ ++ gpio->out |= (1 << offset); ++ ++ ret = i2c_pld_write_byte(gpio->client->addr, gpio->out); ++ ++ rt_mutex_unlock(&adap->bus_lock); ++ ++ return ret; ++} ++ ++static int gw_i2c_pld_get8(struct gpio_chip *chip, unsigned offset) ++{ ++ int ret; ++ s32 value; ++ struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip); ++ struct i2c_adapter *adap = gpio->client->adapter; ++ ++ if (in_atomic() || irqs_disabled()) { ++ ret = rt_mutex_trylock(&adap->bus_lock); ++ if (!ret) ++ /* I2C activity is ongoing. */ ++ return -EAGAIN; ++ } else { ++ rt_mutex_lock(&adap->bus_lock); ++ } ++ ++ value = i2c_pld_read_byte(gpio->client->addr); ++ ++ rt_mutex_unlock(&adap->bus_lock); ++ ++ return (value < 0) ? 0 : (value & (1 << offset)); ++} ++ ++static int gw_i2c_pld_output8(struct gpio_chip *chip, unsigned offset, int value) ++{ ++ int ret; ++ ++ struct gw_i2c_pld *gpio = container_of(chip, struct gw_i2c_pld, chip); ++ struct i2c_adapter *adap = gpio->client->adapter; ++ ++ unsigned bit = 1 << offset; ++ ++ if (in_atomic() || irqs_disabled()) { ++ ret = rt_mutex_trylock(&adap->bus_lock); ++ if (!ret) ++ /* I2C activity is ongoing. */ ++ return -EAGAIN; ++ } else { ++ rt_mutex_lock(&adap->bus_lock); ++ } ++ ++ ++ if (value) ++ gpio->out |= bit; ++ else ++ gpio->out &= ~bit; ++ ++ ret = i2c_pld_write_byte(gpio->client->addr, gpio->out); ++ ++ rt_mutex_unlock(&adap->bus_lock); ++ ++ return ret; ++} ++ ++static void gw_i2c_pld_set8(struct gpio_chip *chip, unsigned offset, int value) ++{ ++ gw_i2c_pld_output8(chip, offset, value); ++} ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int gw_i2c_pld_probe(struct i2c_client *client, ++ const struct i2c_device_id *id) ++{ ++ struct gw_i2c_pld_platform_data *pdata; ++ struct gw_i2c_pld *gpio; ++ int status; ++ ++ pdata = client->dev.platform_data; ++ if (!pdata) ++ return -ENODEV; ++ ++ /* Allocate, initialize, and register this gpio_chip. */ ++ gpio = kzalloc(sizeof *gpio, GFP_KERNEL); ++ if (!gpio) ++ return -ENOMEM; ++ ++ gpio->chip.base = pdata->gpio_base; ++ gpio->chip.can_sleep = 1; ++ gpio->chip.dev = &client->dev; ++ gpio->chip.owner = THIS_MODULE; ++ ++ gpio->chip.ngpio = pdata->nr_gpio; ++ gpio->chip.direction_input = gw_i2c_pld_input8; ++ gpio->chip.get = gw_i2c_pld_get8; ++ gpio->chip.direction_output = gw_i2c_pld_output8; ++ gpio->chip.set = gw_i2c_pld_set8; ++ ++ gpio->chip.label = client->name; ++ ++ gpio->client = client; ++ i2c_set_clientdata(client, gpio); ++ ++ gpio->out = 0xFF; ++ ++ status = gpiochip_add(&gpio->chip); ++ if (status < 0) ++ goto fail; ++ ++ dev_info(&client->dev, "gpios %d..%d on a %s%s\n", ++ gpio->chip.base, ++ gpio->chip.base + gpio->chip.ngpio - 1, ++ client->name, ++ client->irq ? " (irq ignored)" : ""); ++ ++ /* Let platform code set up the GPIOs and their users. ++ * Now is the first time anyone could use them. ++ */ ++ if (pdata->setup) { ++ status = pdata->setup(client, ++ gpio->chip.base, gpio->chip.ngpio, ++ pdata->context); ++ if (status < 0) ++ dev_warn(&client->dev, "setup --> %d\n", status); ++ } ++ ++ return 0; ++ ++fail: ++ dev_dbg(&client->dev, "probe error %d for '%s'\n", ++ status, client->name); ++ kfree(gpio); ++ return status; ++} ++ ++static int gw_i2c_pld_remove(struct i2c_client *client) ++{ ++ struct gw_i2c_pld_platform_data *pdata = client->dev.platform_data; ++ struct gw_i2c_pld *gpio = i2c_get_clientdata(client); ++ int status = 0; ++ ++ if (pdata->teardown) { ++ status = pdata->teardown(client, ++ gpio->chip.base, gpio->chip.ngpio, ++ pdata->context); ++ if (status < 0) { ++ dev_err(&client->dev, "%s --> %d\n", ++ "teardown", status); ++ return status; ++ } ++ } ++ ++ status = gpiochip_remove(&gpio->chip); ++ if (status == 0) ++ kfree(gpio); ++ else ++ dev_err(&client->dev, "%s --> %d\n", "remove", status); ++ return status; ++} ++ ++static struct i2c_driver gw_i2c_pld_driver = { ++ .driver = { ++ .name = "gw_i2c_pld", ++ .owner = THIS_MODULE, ++ }, ++ .probe = gw_i2c_pld_probe, ++ .remove = gw_i2c_pld_remove, ++ .id_table = gw_i2c_pld_id, ++}; ++ ++static int __init gw_i2c_pld_init(void) ++{ ++ return i2c_add_driver(&gw_i2c_pld_driver); ++} ++module_init(gw_i2c_pld_init); ++ ++static void __exit gw_i2c_pld_exit(void) ++{ ++ i2c_del_driver(&gw_i2c_pld_driver); ++} ++module_exit(gw_i2c_pld_exit); ++ ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Chris Lang"); +Index: linux-3.14.25/include/linux/i2c/gw_i2c_pld.h +=================================================================== +--- /dev/null 1970-01-01 00:00:00.000000000 +0000 ++++ linux-3.14.25/include/linux/i2c/gw_i2c_pld.h 2014-11-30 15:26:36.403907355 +0100 +@@ -0,0 +1,20 @@ ++#ifndef __LINUX_GW_I2C_PLD_H ++#define __LINUX_GW_I2C_PLD_H ++ ++/** ++ * The Gateworks I2C PLD Implements an additional 8 bits of GPIO through the PLD ++ */ ++ ++struct gw_i2c_pld_platform_data { ++ unsigned gpio_base; ++ unsigned nr_gpio; ++ int (*setup)(struct i2c_client *client, ++ int gpio, unsigned ngpio, ++ void *context); ++ int (*teardown)(struct i2c_client *client, ++ int gpio, unsigned ngpio, ++ void *context); ++ void *context; ++}; ++ ++#endif /* __LINUX_GW_I2C_PLD_H */ diff --git a/target/linux/ixp4xx/patches-3.14/030-gpio_line_config.patch b/target/linux/ixp4xx/patches-3.14/030-gpio_line_config.patch new file mode 100644 index 0000000..de9197c --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/030-gpio_line_config.patch @@ -0,0 +1,69 @@ +Index: linux-3.14.25/arch/arm/mach-ixp4xx/common.c +=================================================================== +--- linux-3.14.25.orig/arch/arm/mach-ixp4xx/common.c 2014-11-21 18:23:44.000000000 +0100 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/common.c 2014-12-01 07:16:02.172180453 +0100 +@@ -84,22 +84,7 @@ + /* + * GPIO-functions + */ +-/* +- * The following converted to the real HW bits the gpio_line_config +- */ +-/* GPIO pin types */ +-#define IXP4XX_GPIO_OUT 0x1 +-#define IXP4XX_GPIO_IN 0x2 +- +-/* GPIO signal types */ +-#define IXP4XX_GPIO_LOW 0 +-#define IXP4XX_GPIO_HIGH 1 +- +-/* GPIO Clocks */ +-#define IXP4XX_GPIO_CLK_0 14 +-#define IXP4XX_GPIO_CLK_1 15 +- +-static void gpio_line_config(u8 line, u32 direction) ++void gpio_line_config(u8 line, u32 direction) + { + if (direction == IXP4XX_GPIO_IN) + *IXP4XX_GPIO_GPOER |= (1 << line); +@@ -107,12 +92,12 @@ + *IXP4XX_GPIO_GPOER &= ~(1 << line); + } + +-static void gpio_line_get(u8 line, int *value) ++void gpio_line_get(u8 line, int *value) + { + *value = (*IXP4XX_GPIO_GPINR >> line) & 0x1; + } + +-static void gpio_line_set(u8 line, int value) ++void gpio_line_set(u8 line, int value) + { + if (value == IXP4XX_GPIO_HIGH) + *IXP4XX_GPIO_GPOUTR |= (1 << line); +Index: linux-3.14.25/arch/arm/mach-ixp4xx/include/mach/platform.h +=================================================================== +--- linux-3.14.25.orig/arch/arm/mach-ixp4xx/include/mach/platform.h 2014-11-30 15:26:43.020130937 +0100 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/include/mach/platform.h 2014-12-01 07:16:22.024919689 +0100 +@@ -142,5 +142,21 @@ + extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); + extern struct pci_ops ixp4xx_ops; + ++/* GPIO pin types */ ++#define IXP4XX_GPIO_OUT 0x1 ++#define IXP4XX_GPIO_IN 0x2 ++ ++/* GPIO signal types */ ++#define IXP4XX_GPIO_LOW 0 ++#define IXP4XX_GPIO_HIGH 1 ++ ++/* GPIO Clocks */ ++#define IXP4XX_GPIO_CLK_0 14 ++#define IXP4XX_GPIO_CLK_1 15 ++ ++void gpio_line_config(u8 line, u32 direction); ++void gpio_line_get(u8 line, int *value); ++void gpio_line_set(u8 line, int value); ++ + #endif // __ASSEMBLY__ + diff --git a/target/linux/ixp4xx/patches-3.14/090-increase_entropy_pools.patch b/target/linux/ixp4xx/patches-3.14/090-increase_entropy_pools.patch new file mode 100644 index 0000000..991b8d1 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/090-increase_entropy_pools.patch @@ -0,0 +1,17 @@ +--- a/drivers/char/random.c ++++ b/drivers/char/random.c +@@ -280,11 +280,11 @@ + /* + * Configuration information + */ +-#define INPUT_POOL_SHIFT 12 ++#define INPUT_POOL_SHIFT 13 + #define INPUT_POOL_WORDS (1 << (INPUT_POOL_SHIFT-5)) +-#define OUTPUT_POOL_SHIFT 10 ++#define OUTPUT_POOL_SHIFT 11 + #define OUTPUT_POOL_WORDS (1 << (OUTPUT_POOL_SHIFT-5)) +-#define SEC_XFER_SIZE 512 ++#define SEC_XFER_SIZE 1024 + #define EXTRACT_SIZE 10 + + #define DEBUG_RANDOM_BOOT 0 diff --git a/target/linux/ixp4xx/patches-3.14/100-wg302v2_gateway7001_mac_plat_info.patch b/target/linux/ixp4xx/patches-3.14/100-wg302v2_gateway7001_mac_plat_info.patch new file mode 100644 index 0000000..317103f --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/100-wg302v2_gateway7001_mac_plat_info.patch @@ -0,0 +1,78 @@ +--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c ++++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c +@@ -17,6 +17,7 @@ + #include <linux/serial.h> + #include <linux/tty.h> + #include <linux/serial_8250.h> ++#include <linux/dma-mapping.h> + + #include <asm/types.h> + #include <asm/setup.h> +@@ -75,9 +76,37 @@ static struct platform_device gateway700 + .resource = &gateway7001_uart_resource, + }; + ++static struct eth_plat_info gateway7001_plat_eth[] = { ++ { ++ .phy = 1, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 2, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device gateway7001_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = gateway7001_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = gateway7001_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ + static struct platform_device *gateway7001_devices[] __initdata = { + &gateway7001_flash, +- &gateway7001_uart ++ &gateway7001_uart, ++ &gateway7001_eth[0], ++ &gateway7001_eth[1], + }; + + static void __init gateway7001_init(void) +--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c ++++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c +@@ -76,9 +76,26 @@ static struct platform_device wg302v2_ua + .resource = &wg302v2_uart_resource, + }; + ++static struct eth_plat_info wg302v2_plat_eth[] = { ++ { ++ .phy = 8, ++ .rxq = 3, ++ .txreadyq = 20, ++ } ++}; ++ ++static struct platform_device wg302v2_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = wg302v2_plat_eth, ++ } ++}; ++ + static struct platform_device *wg302v2_devices[] __initdata = { + &wg302v2_flash, + &wg302v2_uart, ++ &wg302v2_eth[0], + }; + + static void __init wg302v2_init(void) diff --git a/target/linux/ixp4xx/patches-3.14/105-wg302v1_support.patch b/target/linux/ixp4xx/patches-3.14/105-wg302v1_support.patch new file mode 100644 index 0000000..8793549 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/105-wg302v1_support.patch @@ -0,0 +1,261 @@ +--- a/arch/arm/configs/ixp4xx_defconfig ++++ b/arch/arm/configs/ixp4xx_defconfig +@@ -13,6 +13,7 @@ CONFIG_MACH_AVILA=y + CONFIG_MACH_LOFT=y + CONFIG_ARCH_ADI_COYOTE=y + CONFIG_MACH_GATEWAY7001=y ++CONFIG_MACH_WG302V1=y + CONFIG_MACH_WG302V2=y + CONFIG_ARCH_IXDP425=y + CONFIG_MACH_IXDPG425=y +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -45,6 +45,14 @@ config MACH_GATEWAY7001 + 7001 Access Point. For more information on this platform, + see http://openwrt.org + ++config MACH_WG302V1 ++ bool "Netgear WG302 v1 / WAG302 v1" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support Netgear's ++ WG302 v1 or WAG302 v1 Access Points. For more information ++ on this platform, see http://openwrt.org ++ + config MACH_WG302V2 + bool "Netgear WG302 v2 / WAG302 v2" + select PCI +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -15,6 +15,7 @@ obj-pci-$(CONFIG_MACH_NSLU2) += nslu2-p + obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o + obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o + obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o ++obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o + obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o + obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o + obj-pci-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-pci.o +@@ -33,6 +34,7 @@ obj-$(CONFIG_MACH_NSLU2) += nslu2-setup. + obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o + obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o + obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o ++obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o + obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o + obj-$(CONFIG_MACH_FSG) += fsg-setup.o + obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c +@@ -0,0 +1,63 @@ ++/* ++ * arch/arch/mach-ixp4xx/wg302v1-pci.c ++ * ++ * PCI setup routines for the Netgear WG302 v1 and WAG302 v1 ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Software, Inc. ++ * ++ * Maintainer: Imre Kaloz <kaloz@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++ ++#include <asm/mach/pci.h> ++ ++void __init wg302v1_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init wg302v1_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 1) ++ return IRQ_IXP4XX_GPIO8; ++ else if (slot == 2) ++ return IRQ_IXP4XX_GPIO10; ++ else ++ return -1; ++} ++ ++struct hw_pci wg302v1_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = wg302v1_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = wg302v1_map_irq, ++}; ++ ++int __init wg302v1_pci_init(void) ++{ ++ if (machine_is_wg302v1()) ++ pci_common_init(&wg302v1_pci); ++ return 0; ++} ++ ++subsys_initcall(wg302v1_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c +@@ -0,0 +1,147 @@ ++/* ++ * arch/arm/mach-ixp4xx/wg302v1-setup.c ++ * ++ * Board setup for the Netgear WG302 v1 and WAG302 v1 ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <kaloz@openwrt.org> ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++#include <linux/types.h> ++#include <linux/memory.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/setup.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data wg302v1_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource wg302v1_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device wg302v1_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &wg302v1_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &wg302v1_flash_resource, ++}; ++ ++static struct resource wg302v1_uart_resources[] = { ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++ } ++}; ++ ++static struct plat_serial8250_port wg302v1_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device wg302v1_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = wg302v1_uart_data, ++ }, ++ .num_resources = 2, ++ .resource = wg302v1_uart_resources, ++}; ++ ++static struct eth_plat_info wg302v1_plat_eth[] = { ++ { ++ .phy = 30, ++ .rxq = 3, ++ .txreadyq = 20, ++ } ++}; ++ ++static struct platform_device wg302v1_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = wg302v1_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct platform_device *wg302v1_devices[] __initdata = { ++ &wg302v1_flash, ++ &wg302v1_uart, ++ &wg302v1_eth[0], ++}; ++ ++static void __init wg302v1_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ wg302v1_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ wg302v1_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(wg302v1_devices, ARRAY_SIZE(wg302v1_devices)); ++} ++ ++#ifdef CONFIG_MACH_WG302V1 ++MACHINE_START(WG302V1, "Netgear WG302 v1 / WAG302 v1") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .fixup = wg302v1_fixup, ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = wg302v1_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++#endif diff --git a/target/linux/ixp4xx/patches-3.14/110-pronghorn_series_support.patch b/target/linux/ixp4xx/patches-3.14/110-pronghorn_series_support.patch new file mode 100644 index 0000000..d1fdfcb --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/110-pronghorn_series_support.patch @@ -0,0 +1,393 @@ +--- a/arch/arm/configs/ixp4xx_defconfig ++++ b/arch/arm/configs/ixp4xx_defconfig +@@ -15,6 +15,8 @@ CONFIG_ARCH_ADI_COYOTE=y + CONFIG_MACH_GATEWAY7001=y + CONFIG_MACH_WG302V1=y + CONFIG_MACH_WG302V2=y ++CONFIG_MACH_PRONGHORN=y ++CONFIG_MACH_PRONGHORNMETRO=y + CONFIG_ARCH_IXDP425=y + CONFIG_MACH_IXDPG425=y + CONFIG_MACH_IXDP465=y +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -61,6 +61,22 @@ config MACH_WG302V2 + WG302 v2 or WAG302 v2 Access Points. For more information + on this platform, see http://openwrt.org + ++config MACH_PRONGHORN ++ bool "ADI Pronghorn series" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the ADI ++ Engineering Pronghorn series. For more ++ information on this platform, see http://www.adiengineering.com ++ ++# ++# There're only minimal differences kernel-wise between the Pronghorn and ++# Pronghorn Metro boards - they use different chip selects to drive the ++# CF slot connected to the expansion bus, so we just enable them together. ++# ++config MACH_PRONGHORNMETRO ++ def_bool MACH_PRONGHORN ++ + config ARCH_IXDP425 + bool "IXDP425" + help +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -19,6 +19,7 @@ obj-pci-$(CONFIG_MACH_WG302V1) += wg302 + obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o + obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o + obj-pci-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-pci.o ++obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o + + obj-y += common.o + +@@ -39,6 +40,7 @@ obj-$(CONFIG_MACH_WG302V2) += wg302v2-se + obj-$(CONFIG_MACH_FSG) += fsg-setup.o + obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o + obj-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-setup.o ++obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h ++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h +@@ -42,7 +42,8 @@ static __inline__ void __arch_decomp_set + */ + if (machine_is_adi_coyote() || machine_is_gtwx5715() || + machine_is_gateway7001() || machine_is_wg302v2() || +- machine_is_devixp() || machine_is_miccpt() || machine_is_mic256()) ++ machine_is_devixp() || machine_is_miccpt() || machine_is_mic256() || ++ machine_is_pronghorn() || machine_is_pronghorn_metro()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/pronghorn-pci.c +@@ -0,0 +1,69 @@ ++/* ++ * arch/arch/mach-ixp4xx/pronghorn-pci.c ++ * ++ * PCI setup routines for ADI Engineering Pronghorn series ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Imre Kaloz <kaloz@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++ ++#include <asm/mach/pci.h> ++ ++void __init pronghorn_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init pronghorn_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 13) ++ return IRQ_IXP4XX_GPIO4; ++ else if (slot == 14) ++ return IRQ_IXP4XX_GPIO6; ++ else if (slot == 15) ++ return IRQ_IXP4XX_GPIO11; ++ else if (slot == 16) ++ return IRQ_IXP4XX_GPIO1; ++ else ++ return -1; ++} ++ ++struct hw_pci pronghorn_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = pronghorn_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = pronghorn_map_irq, ++}; ++ ++int __init pronghorn_pci_init(void) ++{ ++ if (machine_is_pronghorn() || machine_is_pronghorn_metro()) ++ pci_common_init(&pronghorn_pci); ++ return 0; ++} ++ ++subsys_initcall(pronghorn_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c +@@ -0,0 +1,252 @@ ++/* ++ * arch/arm/mach-ixp4xx/pronghorn-setup.c ++ * ++ * Board setup for the ADI Engineering Pronghorn series ++ * ++ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++#include <linux/types.h> ++#include <linux/memory.h> ++#include <linux/i2c-gpio.h> ++#include <linux/leds.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/setup.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data pronghorn_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource pronghorn_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device pronghorn_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &pronghorn_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &pronghorn_flash_resource, ++}; ++ ++static struct resource pronghorn_uart_resources [] = { ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ } ++}; ++ ++static struct plat_serial8250_port pronghorn_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device pronghorn_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = pronghorn_uart_data, ++ }, ++ .num_resources = 2, ++ .resource = pronghorn_uart_resources, ++}; ++ ++static struct i2c_gpio_platform_data pronghorn_i2c_gpio_data = { ++ .sda_pin = 9, ++ .scl_pin = 10, ++}; ++ ++static struct platform_device pronghorn_i2c_gpio = { ++ .name = "i2c-gpio", ++ .id = 0, ++ .dev = { ++ .platform_data = &pronghorn_i2c_gpio_data, ++ }, ++}; ++ ++static struct gpio_led pronghorn_led_pin[] = { ++ { ++ .name = "pronghorn:green:status", ++ .gpio = 7, ++ } ++}; ++ ++static struct gpio_led_platform_data pronghorn_led_data = { ++ .num_leds = 1, ++ .leds = pronghorn_led_pin, ++}; ++ ++static struct platform_device pronghorn_led = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev.platform_data = &pronghorn_led_data, ++}; ++ ++static struct resource pronghorn_pata_resources[] = { ++ { ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .name = "intrq", ++ .start = IRQ_IXP4XX_GPIO0, ++ .end = IRQ_IXP4XX_GPIO0, ++ .flags = IORESOURCE_IRQ, ++ }, ++}; ++ ++static struct ixp4xx_pata_data pronghorn_pata_data = { ++ .cs0_bits = 0xbfff0043, ++ .cs1_bits = 0xbfff0043, ++}; ++ ++static struct platform_device pronghorn_pata = { ++ .name = "pata_ixp4xx_cf", ++ .id = 0, ++ .dev.platform_data = &pronghorn_pata_data, ++ .num_resources = ARRAY_SIZE(pronghorn_pata_resources), ++ .resource = pronghorn_pata_resources, ++}; ++ ++static struct eth_plat_info pronghorn_plat_eth[] = { ++ { ++ .phy = 0, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 1, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device pronghorn_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = pronghorn_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = pronghorn_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct platform_device *pronghorn_devices[] __initdata = { ++ &pronghorn_flash, ++ &pronghorn_uart, ++ &pronghorn_led, ++ &pronghorn_eth[0], ++ &pronghorn_eth[1], ++}; ++ ++static void __init pronghorn_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ pronghorn_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ pronghorn_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(pronghorn_devices, ARRAY_SIZE(pronghorn_devices)); ++ ++ if (machine_is_pronghorn()) { ++ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2); ++ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(2); ++ ++ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3); ++ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(3); ++ ++ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS2; ++ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS3; ++ } else { ++ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(3); ++ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(3); ++ ++ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(4); ++ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(4); ++ ++ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS3; ++ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS4; ++ ++ platform_device_register(&pronghorn_i2c_gpio); ++ } ++ ++ platform_device_register(&pronghorn_pata); ++} ++ ++MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = pronghorn_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++ ++MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = pronghorn_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END diff --git a/target/linux/ixp4xx/patches-3.14/111-pronghorn_swap_uarts.patch b/target/linux/ixp4xx/patches-3.14/111-pronghorn_swap_uarts.patch new file mode 100644 index 0000000..ed9f7a7 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/111-pronghorn_swap_uarts.patch @@ -0,0 +1,44 @@ +--- a/arch/arm/mach-ixp4xx/pronghorn-setup.c ++++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c +@@ -52,31 +52,31 @@ static struct platform_device pronghorn_ + + static struct resource pronghorn_uart_resources [] = { + { +- .start = IXP4XX_UART1_BASE_PHYS, +- .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM + }, + { +- .start = IXP4XX_UART2_BASE_PHYS, +- .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM + } + }; + + static struct plat_serial8250_port pronghorn_uart_data[] = { + { +- .mapbase = IXP4XX_UART1_BASE_PHYS, +- .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, +- .irq = IRQ_IXP4XX_UART1, ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { +- .mapbase = IXP4XX_UART2_BASE_PHYS, +- .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, +- .irq = IRQ_IXP4XX_UART2, ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + .regshift = 2, diff --git a/target/linux/ixp4xx/patches-3.14/115-sidewinder_support.patch b/target/linux/ixp4xx/patches-3.14/115-sidewinder_support.patch new file mode 100644 index 0000000..20adbb5 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/115-sidewinder_support.patch @@ -0,0 +1,286 @@ +From 95dac4a842a3c66f69f949b48f9075e16275f77b Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 30 Jun 2013 15:48:47 +0200 +Subject: [PATCH 07/36] 115-sidewinder_support.patch + +--- + arch/arm/mach-ixp4xx/Kconfig | 10 +- + arch/arm/mach-ixp4xx/Makefile | 2 + + arch/arm/mach-ixp4xx/sidewinder-pci.c | 68 ++++++++++++++ + arch/arm/mach-ixp4xx/sidewinder-setup.c | 151 +++++++++++++++++++++++++++++++ + 4 files changed, 230 insertions(+), 1 deletion(-) + create mode 100644 arch/arm/mach-ixp4xx/sidewinder-pci.c + create mode 100644 arch/arm/mach-ixp4xx/sidewinder-setup.c + +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -77,6 +77,14 @@ config MACH_PRONGHORN + config MACH_PRONGHORNMETRO + def_bool MACH_PRONGHORN + ++config MACH_SIDEWINDER ++ bool "ADI Sidewinder" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the ADI ++ Engineering Sidewinder board. For more information on this ++ platform, see http://www.adiengineering.com ++ + config ARCH_IXDP425 + bool "IXDP425" + help +@@ -173,7 +181,7 @@ config MACH_ARCOM_VULCAN + # + config CPU_IXP46X + bool +- depends on MACH_IXDP465 ++ depends on MACH_IXDP465 || MACH_SIDEWINDER + default y + + config CPU_IXP43X +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -20,6 +20,7 @@ obj-pci-$(CONFIG_MACH_WG302V2) += wg302 + obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o + obj-pci-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-pci.o + obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o ++obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o + + obj-y += common.o + +@@ -41,6 +42,7 @@ obj-$(CONFIG_MACH_FSG) += fsg-setup.o + obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o + obj-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-setup.o + obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o ++obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/sidewinder-pci.c +@@ -0,0 +1,67 @@ ++/* ++ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c ++ * ++ * PCI setup routines for ADI Engineering Sidewinder ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Imre Kaloz <kaloz@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++ ++#include <asm/mach/pci.h> ++ ++void __init sidewinder_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init sidewinder_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 1) ++ return IRQ_IXP4XX_GPIO11; ++ else if (slot == 2) ++ return IRQ_IXP4XX_GPIO10; ++ else if (slot == 3) ++ return IRQ_IXP4XX_GPIO9; ++ else ++ return -1; ++} ++ ++struct hw_pci sidewinder_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = sidewinder_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = sidewinder_map_irq, ++}; ++ ++int __init sidewinder_pci_init(void) ++{ ++ if (machine_is_sidewinder()) ++ pci_common_init(&sidewinder_pci); ++ return 0; ++} ++ ++subsys_initcall(sidewinder_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/sidewinder-setup.c +@@ -0,0 +1,155 @@ ++/* ++ * arch/arm/mach-ixp4xx/sidewinder-setup.c ++ * ++ * Board setup for the ADI Engineering Sidewinder ++ * ++ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/serial.h> ++#include <linux/serial_8250.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data sidewinder_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource sidewinder_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device sidewinder_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &sidewinder_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &sidewinder_flash_resource, ++}; ++ ++static struct resource sidewinder_uart_resources[] = { ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++ } ++}; ++ ++static struct plat_serial8250_port sidewinder_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device sidewinder_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = sidewinder_uart_data, ++ }, ++ .num_resources = ARRAY_SIZE(sidewinder_uart_resources), ++ .resource = sidewinder_uart_resources, ++}; ++ ++static struct eth_plat_info sidewinder_plat_eth[] = { ++ { ++ .phy = 5, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0x1e, ++ .rxq = 4, ++ .txreadyq = 21, ++ }, { ++ .phy = 31, ++ .rxq = 2, ++ .txreadyq = 19, ++ } ++}; ++ ++static struct platform_device sidewinder_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = sidewinder_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = sidewinder_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEA, ++ .dev.platform_data = sidewinder_plat_eth + 2, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct platform_device *sidewinder_devices[] __initdata = { ++ &sidewinder_flash, ++ &sidewinder_uart, ++ &sidewinder_eth[0], ++ &sidewinder_eth[1], ++ &sidewinder_eth[2], ++}; ++ ++static void __init sidewinder_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ sidewinder_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ sidewinder_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_64M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(sidewinder_devices, ARRAY_SIZE(sidewinder_devices)); ++} ++ ++MACHINE_START(SIDEWINDER, "ADI Engineering Sidewinder") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = sidewinder_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END diff --git a/target/linux/ixp4xx/patches-3.14/116-sidewinder_fis_location.patch b/target/linux/ixp4xx/patches-3.14/116-sidewinder_fis_location.patch new file mode 100644 index 0000000..7d633f7 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/116-sidewinder_fis_location.patch @@ -0,0 +1,30 @@ +--- a/drivers/mtd/redboot.c ++++ b/drivers/mtd/redboot.c +@@ -30,6 +30,8 @@ + #include <linux/mtd/partitions.h> + #include <linux/module.h> + ++#include <asm/mach-types.h> ++ + struct fis_image_desc { + unsigned char name[16]; // Null terminated name + uint32_t flash_base; // Address within FLASH of image +@@ -47,7 +49,8 @@ struct fis_list { + struct fis_list *next; + }; + +-static int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK; ++int directory = CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK; ++ + module_param(directory, int, 0); + + static inline int redboot_checksum(struct fis_image_desc *img) +@@ -75,6 +78,8 @@ static int parse_redboot_partitions(stru + #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED + static char nullstring[] = "unallocated"; + #endif ++ if (machine_is_sidewinder()) ++ directory = -5; + + if ( directory < 0 ) { + offset = master->size + directory * master->erasesize; diff --git a/target/linux/ixp4xx/patches-3.14/120-compex_support.patch b/target/linux/ixp4xx/patches-3.14/120-compex_support.patch new file mode 100644 index 0000000..2abc159 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/120-compex_support.patch @@ -0,0 +1,199 @@ +From 24025a2dcf1248079dd3019fac6ed955252d277f Mon Sep 17 00:00:00 2001 +From: Imre Kaloz <kaloz@openwrt.org> +Date: Mon, 14 Jul 2008 21:56:34 +0200 +Subject: [PATCH] Add support for the Compex WP18 / NP18A boards + +Signed-off-by: Imre Kaloz <kaloz@openwrt.org> +--- + +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -85,6 +85,14 @@ config MACH_SIDEWINDER + Engineering Sidewinder board. For more information on this + platform, see http://www.adiengineering.com + ++config MACH_COMPEXWP18 ++ bool "Compex WP18 / NP18A" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support Compex' ++ WP18 or NP18A boards. For more information on this ++ platform, see http://www.compex.com.sg/home/OEM/product_ap.htm ++ + config ARCH_IXDP425 + bool "IXDP425" + help +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -21,6 +21,7 @@ obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o + obj-pci-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-pci.o + obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o + obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o ++obj-pci-$(CONFIG_MACH_COMPEXWP18) += ixdp425-pci.o + + obj-y += common.o + +@@ -43,6 +44,7 @@ obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_ + obj-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-setup.o + obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o + obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o ++obj-$(CONFIG_MACH_COMPEXWP18) += compex42x-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/compex42x-setup.c +@@ -0,0 +1,141 @@ ++/* ++ * arch/arm/mach-ixp4xx/compex-setup.c ++ * ++ * Compex WP18 / NP18A board-setup ++ * ++ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/serial.h> ++#include <linux/serial_8250.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data compex42x_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource compex42x_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device compex42x_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &compex42x_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &compex42x_flash_resource, ++}; ++ ++static struct resource compex42x_uart_resources[] = { ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ } ++}; ++ ++static struct plat_serial8250_port compex42x_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device compex42x_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev.platform_data = compex42x_uart_data, ++ .num_resources = 2, ++ .resource = compex42x_uart_resources, ++}; ++ ++static struct eth_plat_info compex42x_plat_eth[] = { ++ { ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0xf0000, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 3, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device compex42x_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = compex42x_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = compex42x_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct platform_device *compex42x_devices[] __initdata = { ++ &compex42x_flash, ++ &compex42x_uart, ++ &compex42x_eth[0], ++ &compex42x_eth[1], ++}; ++ ++static void __init compex42x_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ compex42x_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ compex42x_flash_resource.end = ++ IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ platform_add_devices(compex42x_devices, ARRAY_SIZE(compex42x_devices)); ++} ++ ++MACHINE_START(COMPEXWP18, "Compex WP18 / NP18A") ++ /* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = compex42x_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END +--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c ++++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c +@@ -69,7 +69,8 @@ struct hw_pci ixdp425_pci __initdata = { + int __init ixdp425_pci_init(void) + { + if (machine_is_ixdp425() || machine_is_ixcdp1100() || +- machine_is_ixdp465() || machine_is_kixrp435()) ++ machine_is_ixdp465() || machine_is_kixrp435() || ++ machine_is_compex42x()) + pci_common_init(&ixdp425_pci); + return 0; + } diff --git a/target/linux/ixp4xx/patches-3.14/130-wrt300nv2_support.patch b/target/linux/ixp4xx/patches-3.14/130-wrt300nv2_support.patch new file mode 100644 index 0000000..49359be --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/130-wrt300nv2_support.patch @@ -0,0 +1,227 @@ +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -93,6 +93,14 @@ config MACH_COMPEXWP18 + WP18 or NP18A boards. For more information on this + platform, see http://www.compex.com.sg/home/OEM/product_ap.htm + ++config MACH_WRT300NV2 ++ bool "Linksys WRT300N v2" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support Linksys' ++ WRT300N v2 router. For more information on this ++ platform, see http://openwrt.org ++ + config ARCH_IXDP425 + bool "IXDP425" + help +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -22,6 +22,7 @@ obj-pci-$(CONFIG_MACH_ARCOM_VULCAN) += v + obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o + obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o + obj-pci-$(CONFIG_MACH_COMPEXWP18) += ixdp425-pci.o ++obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o + + obj-y += common.o + +@@ -45,6 +46,7 @@ obj-$(CONFIG_MACH_ARCOM_VULCAN) += vulca + obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o + obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o + obj-$(CONFIG_MACH_COMPEXWP18) += compex42x-setup.o ++obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h ++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h +@@ -43,7 +43,8 @@ static __inline__ void __arch_decomp_set + if (machine_is_adi_coyote() || machine_is_gtwx5715() || + machine_is_gateway7001() || machine_is_wg302v2() || + machine_is_devixp() || machine_is_miccpt() || machine_is_mic256() || +- machine_is_pronghorn() || machine_is_pronghorn_metro()) ++ machine_is_pronghorn() || machine_is_pronghorn_metro() || ++ machine_is_wrt300nv2()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/wrt300nv2-pci.c +@@ -0,0 +1,64 @@ ++/* ++ * arch/arch/mach-ixp4xx/wrt300nv2-pci.c ++ * ++ * PCI setup routines for Linksys WRT300N v2 ++ * ++ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Imre Kaloz <kaloz@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++ ++#include <asm/mach/pci.h> ++ ++extern void ixp4xx_pci_preinit(void); ++extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); ++extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys); ++ ++void __init wrt300nv2_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init wrt300nv2_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 1) ++ return IRQ_IXP4XX_GPIO8; ++ else return -1; ++} ++ ++struct hw_pci wrt300nv2_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = wrt300nv2_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = wrt300nv2_map_irq, ++}; ++ ++int __init wrt300nv2_pci_init(void) ++{ ++ if (machine_is_wrt300nv2()) ++ pci_common_init(&wrt300nv2_pci); ++ return 0; ++} ++ ++subsys_initcall(wrt300nv2_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c +@@ -0,0 +1,110 @@ ++/* ++ * arch/arm/mach-ixp4xx/wrt300nv2-setup.c ++ * ++ * Board setup for the Linksys WRT300N v2 ++ * ++ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++ ++#include <asm/types.h> ++#include <asm/setup.h> ++#include <asm/memory.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data wrt300nv2_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource wrt300nv2_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device wrt300nv2_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &wrt300nv2_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &wrt300nv2_flash_resource, ++}; ++ ++static struct resource wrt300nv2_uart_resource = { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct plat_serial8250_port wrt300nv2_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device wrt300nv2_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = wrt300nv2_uart_data, ++ }, ++ .num_resources = 1, ++ .resource = &wrt300nv2_uart_resource, ++}; ++ ++static struct platform_device *wrt300nv2_devices[] __initdata = { ++ &wrt300nv2_flash, ++ &wrt300nv2_uart ++}; ++ ++static void __init wrt300nv2_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ wrt300nv2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices)); ++} ++ ++#ifdef CONFIG_MACH_WRT300NV2 ++MACHINE_START(WRT300NV2, "Linksys WRT300N v2") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = wrt300nv2_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++#endif diff --git a/target/linux/ixp4xx/patches-3.14/131-wrt300nv2_mac_plat_info.patch b/target/linux/ixp4xx/patches-3.14/131-wrt300nv2_mac_plat_info.patch new file mode 100644 index 0000000..5debbf1 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/131-wrt300nv2_mac_plat_info.patch @@ -0,0 +1,42 @@ +--- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c ++++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c +@@ -76,9 +76,38 @@ static struct platform_device wrt300nv2_ + .resource = &wrt300nv2_uart_resource, + }; + ++/* Built-in 10/100 Ethernet MAC interfaces */ ++static struct eth_plat_info wrt300nv2_plat_eth[] = { ++ { ++ .phy = -1, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 1, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device wrt300nv2_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = wrt300nv2_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = wrt300nv2_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ + static struct platform_device *wrt300nv2_devices[] __initdata = { + &wrt300nv2_flash, +- &wrt300nv2_uart ++ &wrt300nv2_uart, ++ &wrt300nv2_eth[0], ++ &wrt300nv2_eth[1], + }; + + static void __init wrt300nv2_init(void) diff --git a/target/linux/ixp4xx/patches-3.14/132-wrt300nv2_mac_fix.patch b/target/linux/ixp4xx/patches-3.14/132-wrt300nv2_mac_fix.patch new file mode 100644 index 0000000..99db267 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/132-wrt300nv2_mac_fix.patch @@ -0,0 +1,72 @@ +--- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c ++++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c +@@ -3,6 +3,7 @@ + * + * Board setup for the Linksys WRT300N v2 + * ++ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com> + * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> + * + * based on coyote-setup.c: +@@ -18,6 +19,7 @@ + #include <linux/tty.h> + #include <linux/serial_8250.h> + #include <linux/slab.h> ++#include <linux/etherdevice.h> + + #include <asm/types.h> + #include <asm/setup.h> +@@ -79,7 +81,8 @@ static struct platform_device wrt300nv2_ + /* Built-in 10/100 Ethernet MAC interfaces */ + static struct eth_plat_info wrt300nv2_plat_eth[] = { + { +- .phy = -1, ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0x0F0000, + .rxq = 3, + .txreadyq = 20, + }, { +@@ -112,6 +115,10 @@ static struct platform_device *wrt300nv2 + + static void __init wrt300nv2_init(void) + { ++ uint8_t __iomem *f; ++ int offset = 0; ++ int i; ++ + ixp4xx_sys_init(); + + wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); +@@ -121,6 +128,32 @@ static void __init wrt300nv2_init(void) + *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; + + platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices)); ++ ++ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x60000); ++ ++ if (f) { ++ for (i = 0; i < 6; i++) { ++#ifdef __ARMEB__ ++ wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + i); ++ if (i == 5) ++ offset = 1; ++ wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset); ++#else ++ wrt300nv2_plat_eth[0].hwaddr[i] = readb(f + 0x5FFA0 + (i^3)); ++ if (i == 5) ++ offset = 1; ++ wrt300nv2_plat_eth[1].hwaddr[i] = (wrt300nv2_plat_eth[0].hwaddr[i] + offset); ++#endif ++ } ++ iounmap(f); ++ } ++ ++ if (!(is_valid_ether_addr(wrt300nv2_plat_eth[0].hwaddr))) ++ random_ether_addr(wrt300nv2_plat_eth[0].hwaddr); ++ if (!(is_valid_ether_addr(wrt300nv2_plat_eth[1].hwaddr))) { ++ memcpy(wrt300nv2_plat_eth[1].hwaddr, wrt300nv2_plat_eth[0].hwaddr, ETH_ALEN); ++ wrt300nv2_plat_eth[1].hwaddr[5] = (wrt300nv2_plat_eth[0].hwaddr[5] + 1); ++ } + } + + #ifdef CONFIG_MACH_WRT300NV2 diff --git a/target/linux/ixp4xx/patches-3.14/150-lanready_ap1000_support.patch b/target/linux/ixp4xx/patches-3.14/150-lanready_ap1000_support.patch new file mode 100644 index 0000000..ad09efd --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/150-lanready_ap1000_support.patch @@ -0,0 +1,203 @@ +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -101,6 +101,14 @@ config MACH_WRT300NV2 + WRT300N v2 router. For more information on this + platform, see http://openwrt.org + ++config MACH_AP1000 ++ bool "Lanready AP-1000" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support Lanready's ++ AP1000 board. For more information on this ++ platform, see http://openwrt.org ++ + config ARCH_IXDP425 + bool "IXDP425" + help +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -23,6 +23,7 @@ obj-pci-$(CONFIG_MACH_PRONGHORN) += pron + obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o + obj-pci-$(CONFIG_MACH_COMPEXWP18) += ixdp425-pci.o + obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o ++obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o + + obj-y += common.o + +@@ -47,6 +48,7 @@ obj-$(CONFIG_MACH_PRONGHORN) += pronghor + obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o + obj-$(CONFIG_MACH_COMPEXWP18) += compex42x-setup.o + obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o ++obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/ap1000-setup.c +@@ -0,0 +1,154 @@ ++/* ++ * arch/arm/mach-ixp4xx/ap1000-setup.c ++ * ++ * Lanready AP-1000 ++ * ++ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org> ++ * ++ * based on ixdp425-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/types.h> ++#include <asm/setup.h> ++#include <asm/memory.h> ++#include <mach/hardware.h> ++#include <asm/mach-types.h> ++#include <asm/irq.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data ap1000_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource ap1000_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device ap1000_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &ap1000_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &ap1000_flash_resource, ++}; ++ ++static struct resource ap1000_uart_resources[] = { ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ } ++}; ++ ++static struct plat_serial8250_port ap1000_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device ap1000_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev.platform_data = ap1000_uart_data, ++ .num_resources = 2, ++ .resource = ap1000_uart_resources ++}; ++ ++static struct platform_device *ap1000_devices[] __initdata = { ++ &ap1000_flash, ++ &ap1000_uart ++}; ++ ++static char ap1000_mem_fixup[] __initdata = "mem=64M "; ++ ++static void __init ap1000_fixup(struct machine_desc *desc, ++ struct tag *tags, char **cmdline, struct meminfo *mi) ++ ++{ ++ struct tag *t = tags; ++ char *p = *cmdline; ++ ++ /* Find the end of the tags table, taking note of any cmdline tag. */ ++ for (; t->hdr.size; t = tag_next(t)) { ++ if (t->hdr.tag == ATAG_CMDLINE) { ++ p = t->u.cmdline.cmdline; ++ } ++ } ++ ++ /* Overwrite the end of the table with a new cmdline tag. */ ++ t->hdr.tag = ATAG_CMDLINE; ++ t->hdr.size = (sizeof (struct tag_header) + ++ strlen(ap1000_mem_fixup) + strlen(p) + 1 + 4) >> 2; ++ strlcpy(t->u.cmdline.cmdline, ap1000_mem_fixup, COMMAND_LINE_SIZE); ++ strlcpy(t->u.cmdline.cmdline + strlen(ap1000_mem_fixup), p, ++ COMMAND_LINE_SIZE - strlen(ap1000_mem_fixup)); ++ ++ /* Terminate the table. */ ++ t = tag_next(t); ++ t->hdr.tag = ATAG_NONE; ++ t->hdr.size = 0; ++} ++ ++static void __init ap1000_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ ap1000_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ ap1000_flash_resource.end = ++ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; ++ ++ platform_add_devices(ap1000_devices, ARRAY_SIZE(ap1000_devices)); ++} ++ ++#ifdef CONFIG_MACH_AP1000 ++MACHINE_START(AP1000, "Lanready AP-1000") ++ /* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */ ++ .fixup = ap1000_fixup, ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = ap1000_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++#endif +--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c ++++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c +@@ -70,7 +70,7 @@ int __init ixdp425_pci_init(void) + { + if (machine_is_ixdp425() || machine_is_ixcdp1100() || + machine_is_ixdp465() || machine_is_kixrp435() || +- machine_is_compex42x()) ++ machine_is_compex42x() || machine_is_ap1000()) + pci_common_init(&ixdp425_pci); + return 0; + } diff --git a/target/linux/ixp4xx/patches-3.14/151-lanready_ap1000_mac_plat_info.patch b/target/linux/ixp4xx/patches-3.14/151-lanready_ap1000_mac_plat_info.patch new file mode 100644 index 0000000..2079589 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/151-lanready_ap1000_mac_plat_info.patch @@ -0,0 +1,51 @@ +--- a/arch/arm/mach-ixp4xx/ap1000-setup.c ++++ b/arch/arm/mach-ixp4xx/ap1000-setup.c +@@ -91,15 +91,45 @@ static struct platform_device ap1000_uar + .resource = ap1000_uart_resources + }; + ++/* Built-in 10/100 Ethernet MAC interfaces */ ++static struct eth_plat_info ap1000_plat_eth[] = { ++ { ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0x1e, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 5, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device ap1000_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = ap1000_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = ap1000_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ + static struct platform_device *ap1000_devices[] __initdata = { + &ap1000_flash, +- &ap1000_uart ++ &ap1000_uart, ++ &ap1000_eth[0], ++ &ap1000_eth[1], + }; + + static char ap1000_mem_fixup[] __initdata = "mem=64M "; + +-static void __init ap1000_fixup(struct machine_desc *desc, +- struct tag *tags, char **cmdline, struct meminfo *mi) ++static void __init ap1000_fixup(struct tag *tags, char **cmdline, ++ struct meminfo *mi) + + { + struct tag *t = tags; diff --git a/target/linux/ixp4xx/patches-3.14/160-delayed_uart_io.patch b/target/linux/ixp4xx/patches-3.14/160-delayed_uart_io.patch new file mode 100644 index 0000000..1c80d16 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/160-delayed_uart_io.patch @@ -0,0 +1,121 @@ +--- a/drivers/tty/serial/8250/8250_core.c ++++ b/drivers/tty/serial/8250/8250_core.c +@@ -410,6 +410,20 @@ static void mem_serial_out(struct uart_p + writeb(value, p->membase + offset); + } + ++static unsigned int memdelay_serial_in(struct uart_port *p, int offset) ++{ ++ struct uart_8250_port *up = (struct uart_8250_port *)p; ++ udelay(up->port.rw_delay); ++ return mem_serial_in(p, offset); ++} ++ ++static void memdelay_serial_out(struct uart_port *p, int offset, int value) ++{ ++ struct uart_8250_port *up = (struct uart_8250_port *)p; ++ udelay(up->port.rw_delay); ++ mem_serial_out(p, offset, value); ++} ++ + static void mem32_serial_out(struct uart_port *p, int offset, int value) + { + offset = offset << p->regshift; +@@ -461,6 +475,11 @@ static void set_io_from_upio(struct uart + p->serial_out = mem32_serial_out; + break; + ++ case UPIO_MEM_DELAY: ++ p->serial_in = memdelay_serial_in; ++ p->serial_out = memdelay_serial_out; ++ break; ++ + #if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X) + case UPIO_AU: + p->serial_in = au_serial_in; +@@ -486,6 +505,7 @@ serial_port_out_sync(struct uart_port *p + switch (p->iotype) { + case UPIO_MEM: + case UPIO_MEM32: ++ case UPIO_MEM_DELAY: + case UPIO_AU: + p->serial_out(p, offset, value); + p->serial_in(p, UART_LCR); /* safe, no side-effects */ +@@ -2538,6 +2558,7 @@ static int serial8250_request_std_resour + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM: ++ case UPIO_MEM_DELAY: + if (!port->mapbase) + break; + +@@ -2574,6 +2595,7 @@ static void serial8250_release_std_resou + case UPIO_TSI: + case UPIO_MEM32: + case UPIO_MEM: ++ case UPIO_MEM_DELAY: + if (!port->mapbase) + break; + +@@ -3113,6 +3135,7 @@ static int serial8250_probe(struct platf + uart.port.set_termios = p->set_termios; + uart.port.pm = p->pm; + uart.port.dev = &dev->dev; ++ uart.port.rw_delay = p->rw_delay; + uart.port.irqflags |= irqflag; + ret = serial8250_register_8250_port(&uart); + if (ret < 0) { +@@ -3264,6 +3287,7 @@ int serial8250_register_8250_port(struct + uart->port.flags = up->port.flags | UPF_BOOT_AUTOCONF; + uart->bugs = up->bugs; + uart->port.mapbase = up->port.mapbase; ++ uart->port.rw_delay = up->port.rw_delay; + uart->port.private_data = up->port.private_data; + uart->port.fifosize = up->port.fifosize; + uart->tx_loadsz = up->tx_loadsz; +--- a/drivers/tty/serial/serial_core.c ++++ b/drivers/tty/serial/serial_core.c +@@ -2090,6 +2090,7 @@ uart_report_port(struct uart_driver *drv + snprintf(address, sizeof(address), + "I/O 0x%lx offset 0x%x", port->iobase, port->hub6); + break; ++ case UPIO_MEM_DELAY: + case UPIO_MEM: + case UPIO_MEM32: + case UPIO_AU: +@@ -2711,6 +2712,7 @@ int uart_match_port(struct uart_port *po + case UPIO_HUB6: + return (port1->iobase == port2->iobase) && + (port1->hub6 == port2->hub6); ++ case UPIO_MEM_DELAY: + case UPIO_MEM: + case UPIO_MEM32: + case UPIO_AU: +--- a/include/linux/serial_8250.h ++++ b/include/linux/serial_8250.h +@@ -27,6 +27,7 @@ struct plat_serial8250_port { + void *private_data; + unsigned char regshift; /* register shift */ + unsigned char iotype; /* UPIO_* */ ++ unsigned int rw_delay; /* udelay for slower busses IXP4XX Expansion Bus */ + unsigned char hub6; + upf_t flags; /* UPF_* flags */ + unsigned int type; /* If UPF_FIXED_TYPE */ +--- a/include/linux/serial_core.h ++++ b/include/linux/serial_core.h +@@ -141,6 +141,7 @@ struct uart_port { + #define UPIO_MEM32 (3) + #define UPIO_AU (4) /* Au1x00 and RT288x type IO */ + #define UPIO_TSI (5) /* Tsi108/109 type IO */ ++#define UPIO_MEM_DELAY (6) + + unsigned int read_status_mask; /* driver specific */ + unsigned int ignore_status_mask; /* driver specific */ +@@ -189,6 +190,7 @@ struct uart_port { + + unsigned int mctrl; /* current modem ctrl settings */ + unsigned int timeout; /* character-based timeout */ ++ unsigned int rw_delay; /* udelay for slow busses, IXP4XX Expansion Bus */ + unsigned int type; /* port type */ + const struct uart_ops *ops; + unsigned int custom_divisor; diff --git a/target/linux/ixp4xx/patches-3.14/162-wg302v1_mem_fixup.patch b/target/linux/ixp4xx/patches-3.14/162-wg302v1_mem_fixup.patch new file mode 100644 index 0000000..75212bc --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/162-wg302v1_mem_fixup.patch @@ -0,0 +1,38 @@ +--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c ++++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c +@@ -117,6 +117,35 @@ static struct platform_device *wg302v1_d + &wg302v1_eth[0], + }; + ++static char wg302v1_mem_fixup[] __initdata = " mem=32M"; ++ ++static void __init wg302v1_fixup(struct tag *tags, char **cmdline, ++ struct meminfo *mi) ++{ ++ struct tag *t = tags; ++ char *p = *cmdline; ++ size_t fixlen, cmdlen; ++ ++ /* Find the end of the tags table, taking note of any cmdline tag. */ ++ for (; t->hdr.size; t = tag_next(t)) { ++ if (t->hdr.tag == ATAG_CMDLINE) { ++ p = t->u.cmdline.cmdline; ++ } ++ } ++ ++ fixlen = strlen(wg302v1_mem_fixup); ++ cmdlen = strlen(p); ++ if (fixlen + cmdlen >= COMMAND_LINE_SIZE) ++ return; ++ ++ /* append the fixup to the cmdline */ ++ memmove(p + cmdlen, wg302v1_mem_fixup, fixlen + 1); ++ ++ /* Adjust the size of the atag if there was one */ ++ if (t->hdr.size) ++ t->hdr.size += fixlen; ++} ++ + static void __init wg302v1_init(void) + { + ixp4xx_sys_init(); diff --git a/target/linux/ixp4xx/patches-3.14/170-ixdpg425_mac_plat_info.patch b/target/linux/ixp4xx/patches-3.14/170-ixdpg425_mac_plat_info.patch new file mode 100644 index 0000000..f7090cd --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/170-ixdpg425_mac_plat_info.patch @@ -0,0 +1,51 @@ +--- a/arch/arm/mach-ixp4xx/coyote-setup.c ++++ b/arch/arm/mach-ixp4xx/coyote-setup.c +@@ -14,6 +14,7 @@ + #include <linux/serial.h> + #include <linux/tty.h> + #include <linux/serial_8250.h> ++#include <linux/dma-mapping.h> + + #include <asm/types.h> + #include <asm/setup.h> +@@ -81,9 +82,39 @@ static struct platform_device coyote_uar + .resource = &coyote_uart_resource, + }; + ++/* Built-in 10/100 Ethernet MAC interfaces */ ++static struct eth_plat_info ixdpg425_plat_eth[] = { ++ { ++ .phy = 5, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 4, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device ixdpg425_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = ixdpg425_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = ixdpg425_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++ + static struct platform_device *coyote_devices[] __initdata = { + &coyote_flash, +- &coyote_uart ++ &coyote_uart, ++ &ixdpg425_eth[0], ++ &ixdpg425_eth[1], + }; + + static void __init coyote_init(void) diff --git a/target/linux/ixp4xx/patches-3.14/175-avila_hss_audio_support.patch b/target/linux/ixp4xx/patches-3.14/175-avila_hss_audio_support.patch new file mode 100644 index 0000000..ac19851 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/175-avila_hss_audio_support.patch @@ -0,0 +1,2090 @@ +--- a/sound/soc/Kconfig ++++ b/sound/soc/Kconfig +@@ -54,6 +54,7 @@ source "sound/soc/spear/Kconfig" + source "sound/soc/tegra/Kconfig" + source "sound/soc/txx9/Kconfig" + source "sound/soc/ux500/Kconfig" ++source "sound/soc/gw-avila/Kconfig" + + # Supported codecs + source "sound/soc/codecs/Kconfig" +--- a/sound/soc/Makefile ++++ b/sound/soc/Makefile +@@ -31,3 +31,4 @@ obj-$(CONFIG_SND_SOC) += spear/ + obj-$(CONFIG_SND_SOC) += tegra/ + obj-$(CONFIG_SND_SOC) += txx9/ + obj-$(CONFIG_SND_SOC) += ux500/ ++obj-$(CONFIG_SND_SOC) += gw-avila/ +--- /dev/null ++++ b/sound/soc/gw-avila/Kconfig +@@ -0,0 +1,17 @@ ++config SND_GW_AVILA_SOC_PCM ++ tristate ++ ++config SND_GW_AVILA_SOC_HSS ++ tristate ++ ++config SND_GW_AVILA_SOC ++ tristate "SoC Audio for the Gateworks AVILA Family" ++ depends on ARCH_IXP4XX && SND_SOC ++ select SND_GW_AVILA_SOC_PCM ++ select SND_GW_AVILA_SOC_HSS ++ select SND_SOC_TLV320AIC3X ++ help ++ Say Y or M if you want to add support for codecs attached to ++ the Gateworks HSS interface. You will also need ++ to select the audio interfaces to support below. ++ +--- /dev/null ++++ b/sound/soc/gw-avila/Makefile +@@ -0,0 +1,8 @@ ++# Gateworks Avila HSS Platform Support ++snd-soc-gw-avila-objs := gw-avila.o ixp4xx_hss.o ++snd-soc-gw-avila-pcm-objs := gw-avila-pcm.o ++snd-soc-gw-avila-hss-objs := gw-avila-hss.o ++ ++obj-$(CONFIG_SND_GW_AVILA_SOC) += snd-soc-gw-avila.o ++obj-$(CONFIG_SND_GW_AVILA_SOC_PCM) += snd-soc-gw-avila-pcm.o ++obj-$(CONFIG_SND_GW_AVILA_SOC_HSS) += snd-soc-gw-avila-hss.o +--- /dev/null ++++ b/sound/soc/gw-avila/gw-avila-hss.c +@@ -0,0 +1,103 @@ ++/* ++ * gw-avila-hss.c -- HSS Audio Support for Gateworks Avila ++ * ++ * Author: Chris Lang <clang@gateworks.com> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include <linux/init.h> ++#include <linux/module.h> ++#include <linux/platform_device.h> ++#include <linux/interrupt.h> ++#include <linux/wait.h> ++#include <linux/delay.h> ++ ++#include <sound/core.h> ++#include <sound/pcm.h> ++#include <sound/ac97_codec.h> ++#include <sound/initval.h> ++#include <sound/soc.h> ++ ++#include <asm/irq.h> ++#include <linux/mutex.h> ++#include <linux/gpio.h> ++ ++#include "ixp4xx_hss.h" ++#include "gw-avila-hss.h" ++ ++#define gw_avila_hss_suspend NULL ++#define gw_avila_hss_resume NULL ++ ++struct snd_soc_dai_driver gw_avila_hss_dai = { ++ .playback = { ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 | ++ SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | ++ SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | ++ SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 | ++ SNDRV_PCM_RATE_KNOT), ++ .formats = SNDRV_PCM_FMTBIT_S16_LE, }, ++ .capture = { ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 | ++ SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | ++ SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | ++ SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 | ++ SNDRV_PCM_RATE_KNOT), ++ .formats = SNDRV_PCM_FMTBIT_S16_LE, }, ++}; ++ ++static const struct snd_soc_component_driver gw_avila_hss_component = { ++ .name = "gw_avila_hss", ++}; ++ ++static int gw_avila_hss_probe(struct platform_device *pdev) ++{ ++ int port = (pdev->id < 2) ? 0 : 1; ++ int channel = (pdev->id % 2); ++ ++ hss_handle[pdev->id] = hss_init(port, channel); ++ if (!hss_handle[pdev->id]) { ++ return -ENODEV; ++ } ++ ++ return snd_soc_register_component(&pdev->dev, &gw_avila_hss_component, ++ &gw_avila_hss_dai, 1); ++} ++ ++static int gw_avila_hss_remove(struct platform_device *pdev) ++{ ++ snd_soc_unregister_component(&pdev->dev); ++ ++ return 0; ++} ++ ++static struct platform_driver gw_avila_hss_driver = { ++ .probe = gw_avila_hss_probe, ++ .remove = gw_avila_hss_remove, ++ .driver = { ++ .name = "gw_avila_hss", ++ .owner = THIS_MODULE, ++ } ++}; ++ ++static int __init gw_avila_hss_init(void) ++{ ++ return platform_driver_register(&gw_avila_hss_driver); ++} ++module_init(gw_avila_hss_init); ++ ++static void __exit gw_avila_hss_exit(void) ++{ ++ platform_driver_unregister(&gw_avila_hss_driver); ++} ++module_exit(gw_avila_hss_exit); ++ ++MODULE_AUTHOR("Chris Lang"); ++MODULE_DESCRIPTION("HSS Audio Driver for Gateworks Avila"); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/sound/soc/gw-avila/gw-avila-hss.h +@@ -0,0 +1,12 @@ ++/* ++ * Author: Chris Lang <clang@gateworks.com> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#ifndef _GW_AVILA_HSS_H ++#define _GW_AVILA_HSS_H ++ ++#endif +--- /dev/null ++++ b/sound/soc/gw-avila/gw-avila-pcm.c +@@ -0,0 +1,327 @@ ++/* ++ * ALSA PCM interface for the TI DAVINCI processor ++ * ++ * Author: Chris Lang, <clang@gateworks.com> ++ * Copyright: (C) 2009 Gateworks Corporation ++ * ++ * Based On: davinci-evm.c, Author: Vladimir Barinov, <vbarinov@ru.mvista.com> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include <linux/module.h> ++#include <linux/init.h> ++#include <linux/platform_device.h> ++#include <linux/slab.h> ++#include <linux/dma-mapping.h> ++ ++#include <sound/core.h> ++#include <sound/pcm.h> ++#include <sound/pcm_params.h> ++#include <sound/soc.h> ++ ++#include <asm/dma.h> ++ ++#include "gw-avila-pcm.h" ++#include "gw-avila-hss.h" ++#include "ixp4xx_hss.h" ++ ++#define GW_AVILA_PCM_DEBUG 0 ++#if GW_AVILA_PCM_DEBUG ++#define DPRINTK(x...) printk(KERN_DEBUG x) ++#else ++#define DPRINTK(x...) ++#endif ++ ++static struct snd_pcm_hardware gw_avila_pcm_hardware = { ++ .info = (SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER | ++ SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID), ++/* SNDRV_PCM_INFO_PAUSE),*/ ++ .formats = (SNDRV_PCM_FMTBIT_S16_LE), ++ .rates = (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 | ++ SNDRV_PCM_RATE_22050 | SNDRV_PCM_RATE_32000 | ++ SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | ++ SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 | ++ SNDRV_PCM_RATE_KNOT), ++ .rate_min = 8000, ++ .rate_max = 8000, ++ .channels_min = 2, ++ .channels_max = 2, ++ .buffer_bytes_max = 64 * 1024, // All of the lines below may need to be changed ++ .period_bytes_min = 128, ++ .period_bytes_max = 4 * 1024, ++ .periods_min = 16, ++ .periods_max = 32, ++ .fifo_size = 0, ++}; ++ ++struct gw_avila_runtime_data { ++ spinlock_t lock; ++ int period; /* current DMA period */ ++ int master_lch; /* Master DMA channel */ ++ int slave_lch; /* Slave DMA channel */ ++ struct gw_avila_pcm_dma_params *params; /* DMA params */ ++}; ++ ++static void gw_avila_dma_irq(void *data) ++{ ++ struct snd_pcm_substream *substream = data; ++ snd_pcm_period_elapsed(substream); ++} ++ ++static int gw_avila_pcm_trigger(struct snd_pcm_substream *substream, int cmd) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ struct hss_device *hdev = runtime->private_data; ++ int ret = 0; ++ ++ switch (cmd) { ++ case SNDRV_PCM_TRIGGER_START: ++ case SNDRV_PCM_TRIGGER_RESUME: ++ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: ++ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ++ hss_tx_start(hdev); ++ else ++ hss_rx_start(hdev); ++ break; ++ case SNDRV_PCM_TRIGGER_STOP: ++ case SNDRV_PCM_TRIGGER_SUSPEND: ++ case SNDRV_PCM_TRIGGER_PAUSE_PUSH: ++ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ++ hss_tx_stop(hdev); ++ else ++ hss_rx_stop(hdev); ++ break; ++ default: ++ ret = -EINVAL; ++ break; ++ } ++ return ret; ++} ++ ++static int gw_avila_pcm_prepare(struct snd_pcm_substream *substream) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ struct hss_device *hdev = runtime->private_data; ++ ++ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { ++ hss_set_tx_callback(hdev, gw_avila_dma_irq, substream); ++ hss_config_tx_dma(hdev, runtime->dma_area, runtime->buffer_size, runtime->period_size); ++ } else { ++ hss_set_rx_callback(hdev, gw_avila_dma_irq, substream); ++ hss_config_rx_dma(hdev, runtime->dma_area, runtime->buffer_size, runtime->period_size); ++ } ++ ++ return 0; ++} ++ ++static snd_pcm_uframes_t ++gw_avila_pcm_pointer(struct snd_pcm_substream *substream) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ struct hss_device *hdev = runtime->private_data; ++ ++ unsigned int curr = 0; ++ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ++ curr = hss_curr_offset_tx(hdev); ++ else ++ curr = hss_curr_offset_rx(hdev); ++ return curr; ++} ++ ++static int gw_avila_pcm_open(struct snd_pcm_substream *substream) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *cpu_dai = rtd->cpu_dai; ++ ++ snd_soc_set_runtime_hwparams(substream, &gw_avila_pcm_hardware); ++ ++ if (hss_handle[cpu_dai->id] != NULL) ++ runtime->private_data = hss_handle[cpu_dai->id]; ++ else { ++ pr_err("hss_handle is NULL\n"); ++ return -1; ++ } ++ ++ hss_chan_open(hss_handle[cpu_dai->id]); ++ ++ return 0; ++} ++ ++static int gw_avila_pcm_close(struct snd_pcm_substream *substream) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ struct hss_device *hdev = runtime->private_data; ++ ++ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { ++ memset(hdev->tx_buf, 0, runtime->buffer_size); ++ } else ++ memset(hdev->rx_buf, 0, runtime->buffer_size); ++ ++ hss_chan_close(hdev); ++ ++ return 0; ++} ++ ++static int gw_avila_pcm_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *hw_params) ++{ ++ return snd_pcm_lib_malloc_pages(substream, ++ params_buffer_bytes(hw_params)); ++} ++ ++static int gw_avila_pcm_hw_free(struct snd_pcm_substream *substream) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ ++ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ++ memset(runtime->dma_area, 0, runtime->buffer_size); ++ ++ return snd_pcm_lib_free_pages(substream); ++} ++ ++static int gw_avila_pcm_mmap(struct snd_pcm_substream *substream, ++ struct vm_area_struct *vma) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ ++ return dma_mmap_writecombine(substream->pcm->card->dev, vma, ++ runtime->dma_area, ++ runtime->dma_addr, ++ runtime->dma_bytes); ++} ++ ++struct snd_pcm_ops gw_avila_pcm_ops = { ++ .open = gw_avila_pcm_open, ++ .close = gw_avila_pcm_close, ++ .ioctl = snd_pcm_lib_ioctl, ++ .hw_params = gw_avila_pcm_hw_params, ++ .hw_free = gw_avila_pcm_hw_free, ++ .prepare = gw_avila_pcm_prepare, ++ .trigger = gw_avila_pcm_trigger, ++ .pointer = gw_avila_pcm_pointer, ++ .mmap = gw_avila_pcm_mmap, ++}; ++ ++static int gw_avila_pcm_preallocate_dma_buffer(struct snd_pcm *pcm, int stream) ++{ ++ struct snd_pcm_substream *substream = pcm->streams[stream].substream; ++ struct snd_dma_buffer *buf = &substream->dma_buffer; ++ size_t size = gw_avila_pcm_hardware.buffer_bytes_max; ++ ++ buf->dev.type = SNDRV_DMA_TYPE_DEV; ++ buf->dev.dev = pcm->card->dev; ++ buf->private_data = NULL; ++ ++ buf->area = dma_alloc_coherent(pcm->card->dev, size, ++ &buf->addr, GFP_KERNEL); ++ ++ if (!buf->area) { ++ return -ENOMEM; ++ } ++ ++ memset(buf->area, 0xff, size); ++ ++ DPRINTK("preallocate_dma_buffer: area=%p, addr=%p, size=%d\n", ++ (void *) buf->area, (void *) buf->addr, size); ++ ++ buf->bytes = size; ++ ++ return 0; ++} ++ ++static void gw_avila_pcm_free(struct snd_pcm *pcm) ++{ ++ struct snd_pcm_substream *substream; ++ struct snd_dma_buffer *buf; ++ int stream; ++ ++ for (stream = 0; stream < 2; stream++) { ++ substream = pcm->streams[stream].substream; ++ if (!substream) ++ continue; ++ ++ buf = &substream->dma_buffer; ++ if (!buf->area) ++ continue; ++ ++ dma_free_coherent(NULL, buf->bytes, buf->area, 0); ++ buf->area = NULL; ++ } ++} ++ ++static u64 gw_avila_pcm_dmamask = 0xFFFFFFFF; ++ ++static int gw_avila_pcm_new(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_card *card = rtd->card->snd_card; ++ struct snd_pcm *pcm = rtd->pcm; ++ struct snd_soc_dai *dai = rtd->codec_dai; ++ int ret; ++ ++ if (!card->dev->dma_mask) ++ card->dev->dma_mask = &gw_avila_pcm_dmamask; ++ if (!card->dev->coherent_dma_mask) ++ card->dev->coherent_dma_mask = 0xFFFFFFFF; ++ ++ if (dai->driver->playback.channels_min) { ++ ret = gw_avila_pcm_preallocate_dma_buffer(pcm, ++ SNDRV_PCM_STREAM_PLAYBACK); ++ if (ret) ++ return ret; ++ } ++ ++ if (dai->driver->capture.channels_min) { ++ ret = gw_avila_pcm_preallocate_dma_buffer(pcm, ++ SNDRV_PCM_STREAM_CAPTURE); ++ if (ret) ++ return ret; ++ } ++ ++ return 0; ++} ++ ++struct snd_soc_platform_driver gw_avila_soc_platform = { ++ .ops = &gw_avila_pcm_ops, ++ .pcm_new = gw_avila_pcm_new, ++ .pcm_free = gw_avila_pcm_free, ++}; ++ ++static int gw_avila_pcm_platform_probe(struct platform_device *pdev) ++{ ++ return snd_soc_register_platform(&pdev->dev, &gw_avila_soc_platform); ++} ++ ++static int gw_avila_pcm_platform_remove(struct platform_device *pdev) ++{ ++ snd_soc_unregister_platform(&pdev->dev); ++ return 0; ++} ++ ++static struct platform_driver gw_avila_pcm_driver = { ++ .driver = { ++ .name = "gw_avila-audio", ++ .owner = THIS_MODULE, ++ }, ++ .probe = gw_avila_pcm_platform_probe, ++ .remove = gw_avila_pcm_platform_remove, ++}; ++ ++static int __init gw_avila_soc_platform_init(void) ++{ ++ return platform_driver_register(&gw_avila_pcm_driver); ++} ++module_init(gw_avila_soc_platform_init); ++ ++static void __exit gw_avila_soc_platform_exit(void) ++{ ++ platform_driver_unregister(&gw_avila_pcm_driver); ++} ++module_exit(gw_avila_soc_platform_exit); ++ ++MODULE_AUTHOR("Chris Lang"); ++MODULE_DESCRIPTION("Gateworks Avila PCM DMA module"); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/sound/soc/gw-avila/gw-avila-pcm.h +@@ -0,0 +1,32 @@ ++/* ++ * ALSA PCM interface for the Gateworks Avila platform ++ * ++ * Author: Chris Lang, <clang@gateworks.com> ++ * Copyright: (C) 2009 Gateworks Corporation ++ * ++ * Based On: davinci-evm.c, Author: Vladimir Barinov, <vbarinov@ru.mvista.com> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#ifndef _GW_AVILA_PCM_H ++#define _GW_AVILA_PCM_H ++ ++#if 0 ++struct gw_avila_pcm_dma_params { ++ char *name; /* stream identifier */ ++ int channel; /* sync dma channel ID */ ++ dma_addr_t dma_addr; /* device physical address for DMA */ ++ unsigned int data_type; /* xfer data type */ ++}; ++ ++struct gw_avila_snd_platform_data { ++ int tx_dma_ch; // XXX Do we need this? ++ int rx_dma_ch; // XXX Do we need this ++}; ++extern struct snd_soc_platform gw_avila_soc_platform[]; ++#endif ++ ++#endif +--- /dev/null ++++ b/sound/soc/gw-avila/gw-avila.c +@@ -0,0 +1,244 @@ ++/* ++ * File: sound/soc/gw-avila/gw_avila.c ++ * Author: Chris Lang <clang@gateworks.com> ++ * ++ * Created: Tue June 06 2008 ++ * Description: Board driver for Gateworks Avila ++ * ++ * Modified: ++ * Copyright 2009 Gateworks Corporation ++ * ++ * Bugs: What Bugs? ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, see the file COPYING, or write ++ * to the Free Software Foundation, Inc., ++ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA ++ */ ++ ++#include <linux/module.h> ++#include <linux/moduleparam.h> ++#include <linux/device.h> ++#include <asm/dma.h> ++#include <linux/platform_device.h> ++#include <sound/core.h> ++#include <sound/pcm.h> ++#include <sound/soc.h> ++#include <linux/slab.h> ++#include <linux/gpio.h> ++ ++#include "ixp4xx_hss.h" ++#include "gw-avila-hss.h" ++#include "gw-avila-pcm.h" ++ ++#define CODEC_FREQ 33333000 ++ ++static int gw_avila_board_startup(struct snd_pcm_substream *substream) ++{ ++ pr_debug("%s enter\n", __func__); ++ return 0; ++} ++ ++static int gw_avila_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *codec_dai = rtd->codec_dai; ++ struct snd_soc_dai *cpu_dai = rtd->cpu_dai; ++ ++ int ret = 0; ++ ++ /* set codec DAI configuration */ ++ if (cpu_dai->id % 2) { ++ ret = snd_soc_dai_set_fmt(codec_dai, SND_SOC_DAIFMT_DSP_B | SND_SOC_DAIFMT_IB_NF | SND_SOC_DAIFMT_CBS_CFS); ++ snd_soc_dai_set_tdm_slot(codec_dai, 0, 0, 1, 32); ++ } else { ++ ret = snd_soc_dai_set_fmt(codec_dai, SND_SOC_DAIFMT_DSP_B | SND_SOC_DAIFMT_IB_NF | SND_SOC_DAIFMT_CBM_CFM); ++ snd_soc_dai_set_tdm_slot(codec_dai, 0, 0, 0, 32); ++ } ++ ++ if (ret < 0) ++ return ret; ++ ++ /* set the codec system clock */ ++ ret = snd_soc_dai_set_sysclk(codec_dai, 0, CODEC_FREQ, SND_SOC_CLOCK_OUT); ++ if (ret < 0) ++ return ret; ++ ++ return 0; ++} ++ ++static const struct snd_soc_dapm_widget aic3x_dapm_widgets[] = { ++ SND_SOC_DAPM_HP("Headphone Jack", NULL), ++ SND_SOC_DAPM_LINE("Line Out", NULL), ++ SND_SOC_DAPM_LINE("Line In", NULL), ++}; ++ ++static const struct snd_soc_dapm_route audio_map[] = { ++ {"Headphone Jack", NULL, "HPLOUT"}, ++ {"Headphone Jack", NULL, "HPROUT"}, ++ ++ /* Line Out connected to LLOUT, RLOUT */ ++ {"Line Out", NULL, "LLOUT"}, ++ {"Line Out", NULL, "RLOUT"}, ++ ++ /* Line In connected to (LINE1L | LINE2L), (LINE1R | LINE2R) */ ++ {"LINE1L", NULL, "Line In"}, ++ {"LINE1R", NULL, "Line In"}, ++}; ++ ++/* Logic for a aic3x as connected on a davinci-evm */ ++static int avila_aic3x_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_codec *codec = rtd->codec; ++ struct snd_soc_dapm_context *dapm = &codec->dapm; ++ ++ /* Add davinci-evm specific widgets */ ++ snd_soc_dapm_new_controls(dapm, aic3x_dapm_widgets, ++ ARRAY_SIZE(aic3x_dapm_widgets)); ++ ++ /* Set up davinci-evm specific audio path audio_map */ ++ snd_soc_dapm_add_routes(dapm, audio_map, ARRAY_SIZE(audio_map)); ++ ++ /* not connected */ ++ snd_soc_dapm_disable_pin(dapm, "MONO_LOUT"); ++ //snd_soc_dapm_disable_pin(dapm, "HPLCOM"); ++ //snd_soc_dapm_disable_pin(dapm, "HPRCOM"); ++ snd_soc_dapm_disable_pin(dapm, "MIC3L"); ++ snd_soc_dapm_disable_pin(dapm, "MIC3R"); ++ snd_soc_dapm_disable_pin(dapm, "LINE2L"); ++ snd_soc_dapm_disable_pin(dapm, "LINE2R"); ++ ++ /* always connected */ ++ snd_soc_dapm_enable_pin(dapm, "Headphone Jack"); ++ snd_soc_dapm_enable_pin(dapm, "Line Out"); ++ snd_soc_dapm_enable_pin(dapm, "Line In"); ++ ++ snd_soc_dapm_sync(dapm); ++ ++ return 0; ++} ++ ++static struct snd_soc_ops gw_avila_board_ops = { ++ .startup = gw_avila_board_startup, ++ .hw_params = gw_avila_hw_params, ++}; ++ ++static struct snd_soc_dai_link gw_avila_board_dai[] = { ++ { ++ .name = "HSS-0", ++ .stream_name = "HSS-0", ++ .cpu_dai_name = "gw_avila_hss.0", ++ .codec_dai_name = "tlv320aic3x-hifi", ++ .codec_name = "tlv320aic3x-codec.0-001b", ++ .platform_name = "gw_avila-audio.0", ++ .init = avila_aic3x_init, ++ .ops = &gw_avila_board_ops, ++ },{ ++ .name = "HSS-1", ++ .stream_name = "HSS-1", ++ .cpu_dai_name = "gw_avila_hss.1", ++ .codec_dai_name = "tlv320aic3x-hifi", ++ .codec_name = "tlv320aic3x-codec.0-001a", ++ .platform_name = "gw_avila-audio.1", ++ .init = avila_aic3x_init, ++ .ops = &gw_avila_board_ops, ++ },{ ++ .name = "HSS-2", ++ .stream_name = "HSS-2", ++ .cpu_dai_name = "gw_avila_hss.2", ++ .codec_dai_name = "tlv320aic3x-hifi", ++ .codec_name = "tlv320aic3x-codec.0-0019", ++ .platform_name = "gw_avila-audio.2", ++ .init = avila_aic3x_init, ++ .ops = &gw_avila_board_ops, ++ },{ ++ .name = "HSS-3", ++ .stream_name = "HSS-3", ++ .cpu_dai_name = "gw_avila_hss.3", ++ .codec_dai_name = "tlv320aic3x-hifi", ++ .codec_name = "tlv320aic3x-codec.0-0018", ++ .platform_name = "gw_avila-audio.3", ++ .init = avila_aic3x_init, ++ .ops = &gw_avila_board_ops, ++ }, ++}; ++ ++static struct snd_soc_card gw_avila_board[] = { ++ { ++ .name = "gw_avila-board.0", ++ .owner = THIS_MODULE, ++ .dai_link = &gw_avila_board_dai[0], ++ .num_links = 1, ++ },{ ++ .name = "gw_avila-board.1", ++ .owner = THIS_MODULE, ++ .dai_link = &gw_avila_board_dai[1], ++ .num_links = 1, ++ },{ ++ .name = "gw_avila-board.2", ++ .owner = THIS_MODULE, ++ .dai_link = &gw_avila_board_dai[2], ++ .num_links = 1, ++ },{ ++ .name = "gw_avila-board.3", ++ .owner = THIS_MODULE, ++ .dai_link = &gw_avila_board_dai[3], ++ .num_links = 1, ++ } ++}; ++ ++static struct platform_device *gw_avila_board_snd_device[4]; ++ ++static int __init gw_avila_board_init(void) ++{ ++ int ret; ++ struct port *port; ++ int i; ++ ++ if ((hss_port[0] = kzalloc(sizeof(*port), GFP_KERNEL)) == NULL) ++ return -ENOMEM; ++ ++ if ((hss_port[1] = kzalloc(sizeof(*port), GFP_KERNEL)) == NULL) ++ return -ENOMEM; ++ ++ for (i = 0; i < 4; i++) { ++ gw_avila_board_snd_device[i] = platform_device_alloc("soc-audio", i); ++ if (!gw_avila_board_snd_device[i]) { ++ return -ENOMEM; ++ } ++ ++ platform_set_drvdata(gw_avila_board_snd_device[i], &gw_avila_board[i]); ++ ret = platform_device_add(gw_avila_board_snd_device[i]); ++ ++ if (ret) { ++ platform_device_put(gw_avila_board_snd_device[i]); ++ } ++ } ++ return ret; ++} ++ ++static void __exit gw_avila_board_exit(void) ++{ ++ int i; ++ for (i = 0; i < 4; i++) ++ platform_device_unregister(gw_avila_board_snd_device[i]); ++} ++ ++module_init(gw_avila_board_init); ++module_exit(gw_avila_board_exit); ++ ++/* Module information */ ++MODULE_AUTHOR("Chris Lang"); ++MODULE_DESCRIPTION("ALSA SoC HSS Audio gw_avila board"); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/sound/soc/gw-avila/ixp4xx_hss.c +@@ -0,0 +1,902 @@ ++/* ++ * Intel IXP4xx HSS (synchronous serial port) driver for Linux ++ * ++ * Copyright (C) 2009 Chris Lang <clang@gateworks.com> ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of version 2 of the GNU General Public License ++ * as published by the Free Software Foundation. ++ */ ++ ++#include <linux/module.h> ++#include <linux/bitops.h> ++#include <linux/cdev.h> ++#include <linux/dma-mapping.h> ++#include <linux/dmapool.h> ++#include <linux/fs.h> ++#include <linux/io.h> ++#include <linux/kernel.h> ++#include <linux/platform_device.h> ++#include <linux/poll.h> ++#include <linux/slab.h> ++#include <linux/delay.h> ++ ++#include <mach/npe.h> ++#include <mach/qmgr.h> ++ ++#include "ixp4xx_hss.h" ++ ++/***************************************************************************** ++ * global variables ++ ****************************************************************************/ ++ ++void hss_chan_read(unsigned long data); ++static char lock_init = 0; ++static spinlock_t npe_lock; ++static struct npe *npe; ++ ++static const struct { ++ int tx, txdone, rx, rxfree, chan; ++}queue_ids[2] = {{HSS0_PKT_TX0_QUEUE, HSS0_PKT_TXDONE_QUEUE, HSS0_PKT_RX_QUEUE, ++ HSS0_PKT_RXFREE0_QUEUE, HSS0_CHL_RXTRIG_QUEUE}, ++ {HSS1_PKT_TX0_QUEUE, HSS1_PKT_TXDONE_QUEUE, HSS1_PKT_RX_QUEUE, ++ HSS1_PKT_RXFREE0_QUEUE, HSS1_CHL_RXTRIG_QUEUE}, ++}; ++ ++struct port *hss_port[2]; ++struct hss_device *hss_handle[32]; ++EXPORT_SYMBOL(hss_handle); ++ ++/***************************************************************************** ++ * utility functions ++ ****************************************************************************/ ++ ++#ifndef __ARMEB__ ++static inline void memcpy_swab32(u32 *dest, u32 *src, int cnt) ++{ ++ int i; ++ for (i = 0; i < cnt; i++) ++ dest[i] = swab32(src[i]); ++} ++#endif ++ ++static inline unsigned int sub_offset(unsigned int a, unsigned int b, ++ unsigned int modulo) ++{ ++ return (modulo /* make sure the result >= 0 */ + a - b) % modulo; ++} ++ ++/***************************************************************************** ++ * HSS access ++ ****************************************************************************/ ++ ++static void hss_config_load(struct port *port) ++{ ++ struct msg msg; ++ ++ do { ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_CONFIG_LOAD; ++ msg.hss_port = port->id; ++ if (npe_send_message(npe, &msg, "HSS_LOAD_CONFIG")) ++ break; ++ if (npe_recv_message(npe, &msg, "HSS_LOAD_CONFIG")) ++ break; ++ ++ /* HSS_LOAD_CONFIG for port #1 returns port_id = #4 */ ++ if (msg.cmd != PORT_CONFIG_LOAD || msg.data32) ++ break; ++ ++ /* HDLC may stop working without this */ ++ npe_recv_message(npe, &msg, "FLUSH_IT"); ++ return; ++ } while (0); ++ ++ printk(KERN_CRIT "HSS-%i: unable to reload HSS configuration\n", ++ port->id); ++ BUG(); ++} ++ ++static void hss_config_set_pcr(struct port *port) ++{ ++ struct msg msg; ++ ++ do { ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_CONFIG_WRITE; ++ msg.hss_port = port->id; ++ msg.index = HSS_CONFIG_TX_PCR; ++#if 0 ++ msg.data32 = PCR_FRM_SYNC_RISINGEDGE | PCR_MSB_ENDIAN | ++ PCR_TX_DATA_ENABLE | PCR_TX_UNASS_HIGH_IMP | PCR_TX_V56K_HIGH_IMP | PCR_TX_FB_HIGH_IMP; ++#else ++ msg.data32 = PCR_FRM_SYNC_RISINGEDGE | PCR_MSB_ENDIAN | ++ PCR_TX_DATA_ENABLE | PCR_TX_FB_HIGH_IMP | PCR_DCLK_EDGE_RISING; ++#endif ++ if (port->frame_size % 8 == 0) ++ msg.data32 |= PCR_SOF_NO_FBIT; ++ ++ if (npe_send_message(npe, &msg, "HSS_SET_TX_PCR")) ++ break; ++ ++ msg.index = HSS_CONFIG_RX_PCR; ++ msg.data32 &= ~ (PCR_DCLK_EDGE_RISING | PCR_FCLK_EDGE_RISING | PCR_TX_DATA_ENABLE); ++ ++ if (npe_send_message(npe, &msg, "HSS_SET_RX_PCR")) ++ break; ++ return; ++ } while (0); ++ ++ printk(KERN_CRIT "HSS-%i: unable to set HSS PCR registers\n", port->id); ++ BUG(); ++} ++ ++static void hss_config_set_core(struct port *port) ++{ ++ struct msg msg; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_CONFIG_WRITE; ++ msg.hss_port = port->id; ++ msg.index = HSS_CONFIG_CORE_CR; ++#if 0 ++ msg.data32 = 0 | CCR_LOOPBACK | ++ (port->id ? CCR_SECOND_HSS : 0); ++#else ++ msg.data32 = 0 | ++ (port->id ? CCR_SECOND_HSS : 0); ++#endif ++ if (npe_send_message(npe, &msg, "HSS_SET_CORE_CR")) { ++ printk(KERN_CRIT "HSS-%i: unable to set HSS core control" ++ " register\n", port->id); ++ BUG(); ++ } ++} ++ ++static void hss_config_set_line(struct port *port) ++{ ++ struct msg msg; ++ ++ hss_config_set_pcr(port); ++ hss_config_set_core(port); ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_CONFIG_WRITE; ++ msg.hss_port = port->id; ++ msg.index = HSS_CONFIG_CLOCK_CR; ++ msg.data32 = CLK42X_SPEED_8192KHZ /* FIXME */; ++ if (npe_send_message(npe, &msg, "HSS_SET_CLOCK_CR")) { ++ printk(KERN_CRIT "HSS-%i: unable to set HSS clock control" ++ " register\n", port->id); ++ BUG(); ++ } ++} ++ ++static void hss_config_set_rx_frame(struct port *port) ++{ ++ struct msg msg; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_CONFIG_WRITE; ++ msg.hss_port = port->id; ++ msg.index = HSS_CONFIG_RX_FCR; ++ msg.data16a = port->frame_sync_offset; ++ msg.data16b = port->frame_size - 1; ++ if (npe_send_message(npe, &msg, "HSS_SET_RX_FCR")) { ++ printk(KERN_CRIT "HSS-%i: unable to set HSS RX frame size" ++ " and offset\n", port->id); ++ BUG(); ++ } ++} ++ ++static void hss_config_set_frame(struct port *port) ++{ ++ struct msg msg; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_CONFIG_WRITE; ++ msg.hss_port = port->id; ++ msg.index = HSS_CONFIG_TX_FCR; ++ msg.data16a = TX_FRAME_SYNC_OFFSET; ++ msg.data16b = port->frame_size - 1; ++ if (npe_send_message(npe, &msg, "HSS_SET_TX_FCR")) { ++ printk(KERN_CRIT "HSS-%i: unable to set HSS TX frame size" ++ " and offset\n", port->id); ++ BUG(); ++ } ++ hss_config_set_rx_frame(port); ++} ++ ++static void hss_config_set_lut(struct port *port) ++{ ++ struct msg msg; ++ int chan_count = 32; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_CONFIG_WRITE; ++ msg.hss_port = port->id; ++ ++ msg.index = HSS_CONFIG_TX_LUT; ++ msg.data32 = 0xffffffff; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ msg.data32 = 0x0; ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_TX_LUT"); ++ ++ msg.index = HSS_CONFIG_RX_LUT; ++ msg.data32 = 0xffffffff; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ msg.data32 = 0x0; ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ msg.index += 4; ++ npe_send_message(npe, &msg, "HSS_SET_RX_LUT"); ++ ++ hss_config_set_frame(port); ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_NUM_CHANS_WRITE; ++ msg.hss_port = port->id; ++ msg.data8a = chan_count; ++ if (npe_send_message(npe, &msg, "CHAN_NUM_CHANS_WRITE")) { ++ printk(KERN_CRIT "HSS-%i: unable to set HSS channel count\n", ++ port->id); ++ BUG(); ++ } ++} ++ ++static u32 hss_config_get_status(struct port *port) ++{ ++ struct msg msg; ++ ++ do { ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = PORT_ERROR_READ; ++ msg.hss_port = port->id; ++ if (npe_send_message(npe, &msg, "PORT_ERROR_READ")) ++ break; ++ if (npe_recv_message(npe, &msg, "PORT_ERROR_READ")) ++ break; ++ ++ return msg.data32; ++ } while (0); ++ ++ printk(KERN_CRIT "HSS-%i: unable to read HSS status\n", port->id); ++ BUG(); ++} ++ ++static void hss_config_start_chan(struct port *port) ++{ ++ struct msg msg; ++ ++ port->chan_last_tx = 0; ++ port->chan_last_rx = 0; ++ ++ do { ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_RX_BUF_ADDR_WRITE; ++ msg.hss_port = port->id; ++ msg.data32 = port->chan_rx_buf_phys; ++ if (npe_send_message(npe, &msg, "CHAN_RX_BUF_ADDR_WRITE")) ++ break; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_TX_BUF_ADDR_WRITE; ++ msg.hss_port = port->id; ++ msg.data32 = port->chan_tx_pointers_phys; ++ if (npe_send_message(npe, &msg, "CHAN_TX_BUF_ADDR_WRITE")) ++ break; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_FLOW_ENABLE; ++ msg.hss_port = port->id; ++ if (npe_send_message(npe, &msg, "CHAN_FLOW_ENABLE")) ++ break; ++ port->chan_started = 1; ++ return; ++ } while (0); ++ ++ printk(KERN_CRIT "HSS-%i: unable to start channelized flow\n", ++ port->id); ++ BUG(); ++} ++ ++static void hss_config_stop_chan(struct port *port) ++{ ++ struct msg msg; ++ ++ if (!port->chan_started) ++ return; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_FLOW_DISABLE; ++ msg.hss_port = port->id; ++ if (npe_send_message(npe, &msg, "CHAN_FLOW_DISABLE")) { ++ printk(KERN_CRIT "HSS-%i: unable to stop channelized flow\n", ++ port->id); ++ BUG(); ++ } ++ hss_config_get_status(port); /* make sure it's halted */ ++ port->chan_started = 0; ++} ++ ++static int hss_config_load_firmware(struct port *port) ++{ ++ struct msg msg; ++ ++ if (port->initialized) ++ return 0; ++ ++ if (!npe_running(npe)) { ++ int err; ++ if ((err = npe_load_firmware(npe, "NPE-A-HSS", ++ port->dev))) ++ return err; ++ } ++ ++ do { ++ /* HSS main configuration */ ++ hss_config_set_line(port); ++ ++ hss_config_set_frame(port); ++ ++ /* Channelized operation settings */ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_TX_BLK_CFG_WRITE; ++ msg.hss_port = port->id; ++ msg.data8b = (CHAN_TX_LIST_FRAMES & ~7) / 2; ++ msg.data8a = msg.data8b / 4; ++ msg.data8d = CHAN_TX_LIST_FRAMES - msg.data8b; ++ msg.data8c = msg.data8d / 4; ++ if (npe_send_message(npe, &msg, "CHAN_TX_BLK_CFG_WRITE")) ++ break; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_RX_BUF_CFG_WRITE; ++ msg.hss_port = port->id; ++ msg.data8a = CHAN_RX_TRIGGER / 8; ++ msg.data8b = CHAN_RX_FRAMES; ++ if (npe_send_message(npe, &msg, "CHAN_RX_BUF_CFG_WRITE")) ++ break; ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = CHAN_TX_BUF_SIZE_WRITE; ++ msg.hss_port = port->id; ++ msg.data8a = CHAN_TX_LISTS; ++ if (npe_send_message(npe, &msg, "CHAN_TX_BUF_SIZE_WRITE")) ++ break; ++ ++ port->initialized = 1; ++ return 0; ++ } while (0); ++ ++ printk(KERN_CRIT "HSS-%i: unable to start HSS operation\n", port->id); ++ BUG(); ++} ++ ++void hss_chan_irq(void *pdev) ++{ ++ struct port *port = pdev; ++ ++ qmgr_disable_irq(queue_ids[port->id].chan); ++ ++ tasklet_hi_schedule(&port->task); ++} ++ ++ ++int hss_prepare_chan(struct port *port) ++{ ++ int err, i, j; ++ u32 *temp; ++ u32 temp2; ++ u8 *temp3; ++ ++ if (port->initialized) ++ return 0; ++ ++ if ((err = hss_config_load_firmware(port))) ++ return err; ++ ++ if ((err = qmgr_request_queue(queue_ids[port->id].chan, ++ CHAN_QUEUE_LEN, 0, 0, "%s:hss", "hss"))) ++ return err; ++ ++ port->chan_tx_buf = dma_alloc_coherent(port->dev, chan_tx_buf_len(port), &port->chan_tx_buf_phys, GFP_DMA); ++ memset(port->chan_tx_buf, 0, chan_tx_buf_len(port)); ++ ++ port->chan_tx_pointers = dma_alloc_coherent(port->dev, chan_tx_buf_len(port) / CHAN_TX_LIST_FRAMES * 4, &port->chan_tx_pointers_phys, GFP_DMA); ++ ++ temp3 = port->chan_tx_buf; ++ for (i = 0; i < CHAN_TX_LISTS; i++) { ++ for (j = 0; j < 8; j++) { ++ port->tx_lists[i][j] = temp3; ++ temp3 += CHAN_TX_LIST_FRAMES * 4; ++ } ++ } ++ ++ temp = port->chan_tx_pointers; ++ temp2 = port->chan_tx_buf_phys; ++ for (i = 0; i < CHAN_TX_LISTS; i++) ++ { ++ for (j = 0; j < 32; j++) ++ { ++ *temp = temp2; ++ temp2 += CHAN_TX_LIST_FRAMES; ++ temp++; ++ } ++ } ++ ++ port->chan_rx_buf = dma_alloc_coherent(port->dev, chan_rx_buf_len(port), &port->chan_rx_buf_phys, GFP_DMA); ++ ++ for (i = 0; i < 8; i++) { ++ temp3 = port->chan_rx_buf + (i * 4 * 128); ++ for (j = 0; j < 8; j++) { ++ port->rx_frames[i][j] = temp3; ++ temp3 += CHAN_RX_TRIGGER; ++ } ++ } ++ ++ qmgr_set_irq(queue_ids[port->id].chan, QUEUE_IRQ_SRC_NOT_EMPTY, ++ hss_chan_irq, port); ++ ++ return 0; ++ ++} ++ ++int hss_tx_start(struct hss_device *hdev) ++{ ++ unsigned long flags; ++ struct port *port = hdev->port; ++ ++ hdev->tx_loc = 0; ++ hdev->tx_frame = 0; ++ ++ set_bit((1 << hdev->id), &port->chan_tx_bitmap); ++ ++ if (!port->chan_started) ++ { ++ qmgr_enable_irq(queue_ids[port->id].chan); ++ spin_lock_irqsave(&npe_lock, flags); ++ hss_config_start_chan(port); ++ spin_unlock_irqrestore(&npe_lock, flags); ++ hss_chan_irq(port); ++ } ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_tx_start); ++ ++int hss_rx_start(struct hss_device *hdev) ++{ ++ unsigned long flags; ++ struct port *port = hdev->port; ++ ++ hdev->rx_loc = 0; ++ hdev->rx_frame = 0; ++ ++ set_bit((1 << hdev->id), &port->chan_rx_bitmap); ++ ++ if (!port->chan_started) ++ { ++ qmgr_enable_irq(queue_ids[port->id].chan); ++ spin_lock_irqsave(&npe_lock, flags); ++ hss_config_start_chan(port); ++ spin_unlock_irqrestore(&npe_lock, flags); ++ hss_chan_irq(port); ++ } ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_rx_start); ++ ++int hss_tx_stop(struct hss_device *hdev) ++{ ++ struct port *port = hdev->port; ++ ++ clear_bit((1 << hdev->id), &port->chan_tx_bitmap); ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_tx_stop); ++ ++int hss_rx_stop(struct hss_device *hdev) ++{ ++ struct port *port = hdev->port; ++ ++ clear_bit((1 << hdev->id), &port->chan_rx_bitmap); ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_rx_stop); ++ ++int hss_chan_open(struct hss_device *hdev) ++{ ++ struct port *port = hdev->port; ++ int i, err = 0; ++ ++ if (port->chan_open) ++ return 0; ++ ++ if (port->mode == MODE_HDLC) { ++ err = -ENOSYS; ++ goto out; ++ } ++ ++ if (port->mode == MODE_G704 && port->channels[0] == hdev->id) { ++ err = -EBUSY; /* channel #0 is used for G.704 signaling */ ++ goto out; ++ } ++ ++ for (i = MAX_CHANNELS; i > port->frame_size / 8; i--) ++ if (port->channels[i - 1] == hdev->id) { ++ err = -ECHRNG; /* frame too short */ ++ goto out; ++ } ++ ++ hdev->rx_loc = hdev->tx_loc = 0; ++ hdev->rx_frame = hdev->tx_frame = 0; ++ ++ //clear_bit((1 << hdev->id), &port->chan_rx_bitmap); ++ //clear_bit((1 << hdev->id), &port->chan_tx_bitmap); ++ ++ if (!port->initialized) { ++ hss_prepare_chan(port); ++ ++ hss_config_stop_chan(port); ++ hdev->open_count++; ++ port->chan_open_count++; ++ ++ hss_config_set_lut(port); ++ hss_config_load(port); ++ ++ } ++ port->chan_open = 1; ++ ++out: ++ return err; ++} ++EXPORT_SYMBOL(hss_chan_open); ++ ++int hss_chan_close(struct hss_device *hdev) ++{ ++ return 0; ++} ++EXPORT_SYMBOL(hss_chan_close); ++ ++void hss_chan_read(unsigned long data) ++{ ++ struct port *port = (void *)data; ++ struct hss_device *hdev; ++ u8 *hw_buf, *save_buf; ++ u8 *buf; ++ u32 v; ++ unsigned int tx_list, rx_frame; ++ int i, j, channel; ++ u8 more_work = 0; ++ ++/* ++ My Data in the hardware buffer is scattered by channels into 4 trunks ++ as follows for rx ++ ++ channel 0 channel 1 channel 2 channel 3 ++Trunk 1 = 0 -> 127 128 -> 255 256 -> 383 384 -> 512 ++Trunk 2 = 513 -> 639 640 -> 768 769 -> 895 896 -> 1023 ++Trunk 3 = 1024 -> 1151 1152 -> 1207 1208 -> 1407 1408 -> 1535 ++Trunk 4 = 1535 -> 1663 1664 -> 1791 1792 -> 1920 1921 -> 2047 ++ ++ I will get CHAN_RX_TRIGGER worth of bytes out of each channel on each trunk ++ with each IRQ ++ ++ For TX Data, it is split into 8 lists with each list containing 16 bytes per ++ channel ++ ++Trunk 1 = 0 -> 16 17 -> 32 33 -> 48 49 -> 64 ++Trunk 2 = 65 -> 80 81 -> 96 97 -> 112 113 -> 128 ++Trunk 3 = 129 -> 144 145 -> 160 161 -> 176 177 -> 192 ++Trunk 4 = 193 -> 208 209 -> 224 225 -> 240 241 -> 256 ++ ++*/ ++ ++ ++ while ((v = qmgr_get_entry(queue_ids[port->id].chan))) ++ { ++ tx_list = (v >> 8) & 0xFF; ++ rx_frame = v & 0xFF; ++ ++ if (tx_list == 7) ++ tx_list = 0; ++ else ++ tx_list++; ++ for (channel = 0; channel < 8; channel++) { ++ ++ hdev = port->chan_devices[channel]; ++ if (!hdev) ++ continue; ++ ++ if (test_bit(1 << channel, &port->chan_tx_bitmap)) { ++ buf = (u8 *)hdev->tx_buf + hdev->tx_loc; ++#if 0 ++ hw_buf = (u8 *)port->chan_tx_buf; ++ hw_buf += (tx_list * CHAN_TX_LIST_FRAMES * 32); ++ hw_buf += (4 * CHAN_TX_LIST_FRAMES * channel); ++ save_buf = hw_buf; ++#else ++ save_buf = port->tx_lists[tx_list][channel]; ++#endif ++ for (i = 0; i < CHAN_TX_LIST_FRAMES; i++) { ++ hw_buf = save_buf + i; ++ for (j = 0; j < 4; j++) { ++ *hw_buf = *(buf++); ++ hw_buf += CHAN_TX_LIST_FRAMES; ++ } ++ ++ hdev->tx_loc += 4; ++ hdev->tx_frame++; ++ if (hdev->tx_loc >= hdev->tx_buffer_size) { ++ hdev->tx_loc = 0; ++ buf = (u8 *)hdev->tx_buf; ++ } ++ } ++ } else { ++#if 0 ++ hw_buf = (u8 *)port->chan_tx_buf; ++ hw_buf += (tx_list * CHAN_TX_LIST_FRAMES * 32); ++ hw_buf += (4 * CHAN_TX_LIST_FRAMES * channel); ++#else ++ hw_buf = port->tx_lists[tx_list][channel]; ++#endif ++ memset(hw_buf, 0, 64); ++ } ++ ++ if (hdev->tx_frame >= hdev->tx_period_size && test_bit(1 << channel, &port->chan_tx_bitmap)) ++ { ++ hdev->tx_frame %= hdev->tx_period_size; ++ if (hdev->tx_callback) ++ hdev->tx_callback(hdev->tx_data); ++ more_work = 1; ++ } ++ ++ if (test_bit(1 << channel, &port->chan_rx_bitmap)) { ++ buf = (u8 *)hdev->rx_buf + hdev->rx_loc; ++#if 0 ++ hw_buf = (u8 *)port->chan_rx_buf; ++ hw_buf += (4 * CHAN_RX_FRAMES * channel); ++ hw_buf += rx_frame; ++ save_buf = hw_buf; ++#else ++ save_buf = port->rx_frames[channel][rx_frame >> 4]; ++#endif ++ for (i = 0; i < CHAN_RX_TRIGGER; i++) { ++ hw_buf = save_buf + i; ++ for (j = 0; j < 4; j++) { ++ *(buf++) = *hw_buf; ++ hw_buf += CHAN_RX_FRAMES; ++ } ++ hdev->rx_loc += 4; ++ hdev->rx_frame++; ++ if (hdev->rx_loc >= hdev->rx_buffer_size) { ++ hdev->rx_loc = 0; ++ buf = (u8 *)hdev->rx_buf; ++ } ++ } ++ } ++ ++ if (hdev->rx_frame >= hdev->rx_period_size && test_bit(1 << channel, &port->chan_rx_bitmap)) ++ { ++ hdev->rx_frame %= hdev->rx_period_size; ++ if (hdev->rx_callback) ++ hdev->rx_callback(hdev->rx_data); ++ more_work = 1; ++ } ++ } ++#if 0 ++ if (more_work) ++ { ++ tasklet_hi_schedule(&port->task); ++ return; ++ } ++#endif ++ } ++ ++ qmgr_enable_irq(queue_ids[port->id].chan); ++ ++ return; ++ ++} ++ ++struct hss_device *hss_chan_create(struct port *port, unsigned int channel) ++{ ++ struct hss_device *chan_dev; ++ unsigned long flags; ++ ++ chan_dev = kzalloc(sizeof(struct hss_device), GFP_KERNEL); ++ ++ spin_lock_irqsave(&npe_lock, flags); ++ ++ chan_dev->id = channel; ++ chan_dev->port = port; ++ ++ port->channels[channel] = channel; ++ ++ port->chan_devices[channel] = chan_dev; ++ ++ spin_unlock_irqrestore(&npe_lock, flags); ++ ++ return chan_dev; ++} ++ ++/***************************************************************************** ++ * initialization ++ ****************************************************************************/ ++ ++static struct platform_device gw_avila_hss_device_0 = { ++ .name = "ixp4xx_hss", ++ .id = 0, ++}; ++ ++static struct platform_device gw_avila_hss_device_1 = { ++ .name = "ixp4xx_hss", ++ .id = 1, ++}; ++ ++static struct platform_device *gw_avila_hss_port_0; ++static struct platform_device *gw_avila_hss_port_1; ++static u64 hss_dmamask = 0xFFFFFFFF; ++ ++struct hss_device *hss_init(int id, int channel) ++{ ++ struct port *port = hss_port[id]; ++ struct hss_device *hdev; ++ int ret; ++ ++ if (!lock_init) ++ { ++ spin_lock_init(&npe_lock); ++ lock_init = 1; ++ npe = npe_request(0); ++ } ++ ++ if (!port->init) { ++ if (id == 0) { ++ gw_avila_hss_port_0 = platform_device_alloc("hss-port", 0); ++ ++ platform_set_drvdata(gw_avila_hss_port_0, &gw_avila_hss_device_0); ++ port->dev = &gw_avila_hss_port_0->dev; ++ ++ if (!port->dev->dma_mask) ++ port->dev->dma_mask = &hss_dmamask; ++ if (!port->dev->coherent_dma_mask) ++ port->dev->coherent_dma_mask = 0xFFFFFFFF; ++ ++ ret = platform_device_add(gw_avila_hss_port_0); ++ ++ if (ret) ++ platform_device_put(gw_avila_hss_port_0); ++ ++ tasklet_init(&port->task, hss_chan_read, (unsigned long) port); ++ } ++ else ++ { ++ gw_avila_hss_port_1 = platform_device_alloc("hss-port", 1); ++ ++ platform_set_drvdata(gw_avila_hss_port_1, &gw_avila_hss_device_1); ++ port->dev = &gw_avila_hss_port_1->dev; ++ ++ if (!port->dev->dma_mask) ++ port->dev->dma_mask = &hss_dmamask; ++ if (!port->dev->coherent_dma_mask) ++ port->dev->coherent_dma_mask = 0xFFFFFFFF; ++ ++ ret = platform_device_add(gw_avila_hss_port_1); ++ ++ if (ret) ++ platform_device_put(gw_avila_hss_port_1); ++ ++ tasklet_init(&port->task, hss_chan_read, (unsigned long) port); ++ } ++ ++ port->init = 1; ++ port->id = id; ++ port->clock_type = CLOCK_EXT; ++ port->clock_rate = 8192000; ++ port->frame_size = 256; /* E1 */ ++ port->mode = MODE_RAW; ++ port->next_rx_frame = 0; ++ memset(port->channels, CHANNEL_UNUSED, sizeof(port->channels)); ++ } ++ ++ hdev = hss_chan_create(port, channel); ++ ++ return hdev; ++} ++EXPORT_SYMBOL(hss_init); ++ ++int hss_set_tx_callback(struct hss_device *hdev, void (*tx_callback)(void *), void *tx_data) ++{ ++ BUG_ON(tx_callback == NULL); ++ hdev->tx_callback = tx_callback; ++ hdev->tx_data = tx_data; ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_set_tx_callback); ++ ++int hss_set_rx_callback(struct hss_device *hdev, void (*rx_callback)(void *), void *rx_data) ++{ ++ BUG_ON(rx_callback == NULL); ++ hdev->rx_callback = rx_callback; ++ hdev->rx_data = rx_data; ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_set_rx_callback); ++ ++int hss_config_rx_dma(struct hss_device *hdev, void *buf, size_t buffer_size, size_t period_size) ++{ ++ /* ++ * Period Size and Buffer Size are in Frames which are u32 ++ * We convert the u32 *buf to u8 in order to make channel reads ++ * and rx_loc easier ++ */ ++ ++ hdev->rx_buf = (u8 *)buf; ++ hdev->rx_buffer_size = buffer_size << 2; ++ hdev->rx_period_size = period_size; ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_config_rx_dma); ++ ++int hss_config_tx_dma(struct hss_device *hdev, void *buf, size_t buffer_size, size_t period_size) ++{ ++ /* ++ * Period Size and Buffer Size are in Frames which are u32 ++ * We convert the u32 *buf to u8 in order to make channel reads ++ * and rx_loc easier ++ */ ++ ++ hdev->tx_buf = (u8 *)buf; ++ hdev->tx_buffer_size = buffer_size << 2; ++ hdev->tx_period_size = period_size; ++ ++ return 0; ++} ++EXPORT_SYMBOL(hss_config_tx_dma); ++ ++unsigned long hss_curr_offset_rx(struct hss_device *hdev) ++{ ++ return hdev->rx_loc >> 2; ++} ++EXPORT_SYMBOL(hss_curr_offset_rx); ++ ++unsigned long hss_curr_offset_tx(struct hss_device *hdev) ++{ ++ return hdev->tx_loc >> 2; ++} ++EXPORT_SYMBOL(hss_curr_offset_tx); ++ ++MODULE_AUTHOR("Chris Lang"); ++MODULE_DESCRIPTION("Intel IXP4xx HSS Audio driver"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/gw-avila/ixp4xx_hss.h +@@ -0,0 +1,401 @@ ++/* ++ * ++ * ++ * Copyright (C) 2009 Gateworks Corporation ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of version 2 of the GNU General Public License ++ * as published by the Free Software Foundation. ++ */ ++ ++#include <linux/types.h> ++#include <linux/bitops.h> ++#include <linux/dma-mapping.h> ++#include <linux/dmapool.h> ++#include <linux/fs.h> ++#include <linux/io.h> ++#include <linux/kernel.h> ++#include <linux/platform_device.h> ++#include <linux/poll.h> ++#include <mach/npe.h> ++#include <mach/qmgr.h> ++#include <linux/interrupt.h> ++ ++//#include <linux/hdlc.h> XXX We aren't HDLC ++ ++#define DEBUG_QUEUES 0 ++#define DEBUG_DESC 0 ++#define DEBUG_RX 0 ++#define DEBUG_TX 0 ++#define DEBUG_PKT_BYTES 0 ++#define DEBUG_CLOSE 0 ++#define DEBUG_FRAMER 0 ++ ++#define DRV_NAME "ixp4xx_hss" ++ ++#define PKT_EXTRA_FLAGS 0 /* orig 1 */ ++#define TX_FRAME_SYNC_OFFSET 0 /* channelized */ ++#define PKT_NUM_PIPES 1 /* 1, 2 or 4 */ ++#define PKT_PIPE_FIFO_SIZEW 4 /* total 4 dwords per HSS */ ++ ++#define RX_DESCS 512 /* also length of all RX queues */ ++#define TX_DESCS 512 /* also length of all TX queues */ ++ ++//#define POOL_ALLOC_SIZE (sizeof(struct desc) * (RX_DESCS + TX_DESCS)) ++#define RX_SIZE (HDLC_MAX_MRU + 4) /* NPE needs more space */ ++#define MAX_CLOSE_WAIT 1000 /* microseconds */ ++#define HSS_COUNT 2 ++#define MIN_FRAME_SIZE 16 /* bits */ ++#define MAX_FRAME_SIZE 257 /* 256 bits + framing bit */ ++#define MAX_CHANNELS (MAX_FRAME_SIZE / 8) ++#define MAX_CHAN_DEVICES 32 ++#define CHANNEL_HDLC 0xFE ++#define CHANNEL_UNUSED 0xFF ++ ++#define NAPI_WEIGHT 16 ++#define CHAN_RX_TRIGGER 16 /* 8 RX frames = 1 ms @ E1 */ ++#define CHAN_RX_FRAMES 128 ++#define CHAN_RX_TRUNKS 1 ++#define MAX_CHAN_RX_BAD_SYNC (CHAN_RX_TRIGGER / 2 /* pairs */ - 3) ++ ++#define CHAN_TX_LIST_FRAMES CHAN_RX_TRIGGER /* bytes/channel per list, 16 - 48 */ ++#define CHAN_TX_LISTS 8 ++#define CHAN_TX_TRUNKS CHAN_RX_TRUNKS ++#define CHAN_TX_FRAMES (CHAN_TX_LIST_FRAMES * CHAN_TX_LISTS) ++ ++#define CHAN_QUEUE_LEN 32 /* minimum possible */ ++ ++#define chan_rx_buf_len(port) (port->frame_size / 8 * CHAN_RX_FRAMES * CHAN_RX_TRUNKS) ++#define chan_tx_buf_len(port) (port->frame_size / 8 * CHAN_TX_FRAMES * CHAN_TX_TRUNKS) ++ ++/* Queue IDs */ ++#define HSS0_CHL_RXTRIG_QUEUE 12 /* orig size = 32 dwords */ ++#define HSS0_PKT_RX_QUEUE 13 /* orig size = 32 dwords */ ++#define HSS0_PKT_TX0_QUEUE 14 /* orig size = 16 dwords */ ++#define HSS0_PKT_TX1_QUEUE 15 ++#define HSS0_PKT_TX2_QUEUE 16 ++#define HSS0_PKT_TX3_QUEUE 17 ++#define HSS0_PKT_RXFREE0_QUEUE 18 /* orig size = 16 dwords */ ++#define HSS0_PKT_RXFREE1_QUEUE 19 ++#define HSS0_PKT_RXFREE2_QUEUE 20 ++#define HSS0_PKT_RXFREE3_QUEUE 21 ++#define HSS0_PKT_TXDONE_QUEUE 22 /* orig size = 64 dwords */ ++ ++#define HSS1_CHL_RXTRIG_QUEUE 10 ++#define HSS1_PKT_RX_QUEUE 0 ++#define HSS1_PKT_TX0_QUEUE 5 ++#define HSS1_PKT_TX1_QUEUE 6 ++#define HSS1_PKT_TX2_QUEUE 7 ++#define HSS1_PKT_TX3_QUEUE 8 ++#define HSS1_PKT_RXFREE0_QUEUE 1 ++#define HSS1_PKT_RXFREE1_QUEUE 2 ++#define HSS1_PKT_RXFREE2_QUEUE 3 ++#define HSS1_PKT_RXFREE3_QUEUE 4 ++#define HSS1_PKT_TXDONE_QUEUE 9 ++ ++#define NPE_PKT_MODE_HDLC 0 ++#define NPE_PKT_MODE_RAW 1 ++#define NPE_PKT_MODE_56KMODE 2 ++#define NPE_PKT_MODE_56KENDIAN_MSB 4 ++ ++/* PKT_PIPE_HDLC_CFG_WRITE flags */ ++#define PKT_HDLC_IDLE_ONES 0x1 /* default = flags */ ++#define PKT_HDLC_CRC_32 0x2 /* default = CRC-16 */ ++#define PKT_HDLC_MSB_ENDIAN 0x4 /* default = LE */ ++ ++ ++/* hss_config, PCRs */ ++/* Frame sync sampling, default = active low */ ++#define PCR_FRM_SYNC_ACTIVE_HIGH 0x40000000 ++#define PCR_FRM_SYNC_FALLINGEDGE 0x80000000 ++#define PCR_FRM_SYNC_RISINGEDGE 0xC0000000 ++ ++/* Frame sync pin: input (default) or output generated off a given clk edge */ ++#define PCR_FRM_SYNC_OUTPUT_FALLING 0x20000000 ++#define PCR_FRM_SYNC_OUTPUT_RISING 0x30000000 ++ ++/* Frame and data clock sampling on edge, default = falling */ ++#define PCR_FCLK_EDGE_RISING 0x08000000 ++#define PCR_DCLK_EDGE_RISING 0x04000000 ++ ++/* Clock direction, default = input */ ++#define PCR_SYNC_CLK_DIR_OUTPUT 0x02000000 ++ ++/* Generate/Receive frame pulses, default = enabled */ ++#define PCR_FRM_PULSE_DISABLED 0x01000000 ++ ++ /* Data rate is full (default) or half the configured clk speed */ ++#define PCR_HALF_CLK_RATE 0x00200000 ++ ++/* Invert data between NPE and HSS FIFOs? (default = no) */ ++#define PCR_DATA_POLARITY_INVERT 0x00100000 ++ ++/* TX/RX endianness, default = LSB */ ++#define PCR_MSB_ENDIAN 0x00080000 ++ ++/* Normal (default) / open drain mode (TX only) */ ++#define PCR_TX_PINS_OPEN_DRAIN 0x00040000 ++ ++/* No framing bit transmitted and expected on RX? (default = framing bit) */ ++#define PCR_SOF_NO_FBIT 0x00020000 ++ ++/* Drive data pins? */ ++#define PCR_TX_DATA_ENABLE 0x00010000 ++ ++/* Voice 56k type: drive the data pins low (default), high, high Z */ ++#define PCR_TX_V56K_HIGH 0x00002000 ++#define PCR_TX_V56K_HIGH_IMP 0x00004000 ++ ++/* Unassigned type: drive the data pins low (default), high, high Z */ ++#define PCR_TX_UNASS_HIGH 0x00000800 ++#define PCR_TX_UNASS_HIGH_IMP 0x00001000 ++ ++/* T1 @ 1.544MHz only: Fbit dictated in FIFO (default) or high Z */ ++#define PCR_TX_FB_HIGH_IMP 0x00000400 ++ ++/* 56k data endiannes - which bit unused: high (default) or low */ ++#define PCR_TX_56KE_BIT_0_UNUSED 0x00000200 ++ ++/* 56k data transmission type: 32/8 bit data (default) or 56K data */ ++#define PCR_TX_56KS_56K_DATA 0x00000100 ++ ++/* hss_config, cCR */ ++/* Number of packetized clients, default = 1 */ ++#define CCR_NPE_HFIFO_2_HDLC 0x04000000 ++#define CCR_NPE_HFIFO_3_OR_4HDLC 0x08000000 ++ ++/* default = no loopback */ ++#define CCR_LOOPBACK 0x02000000 ++ ++/* HSS number, default = 0 (first) */ ++#define CCR_SECOND_HSS 0x01000000 ++ ++ ++/* hss_config, clkCR: main:10, num:10, denom:12 */ ++#define CLK42X_SPEED_EXP ((0x3FF << 22) | ( 2 << 12) | 15) /*65 KHz*/ ++ ++#define CLK42X_SPEED_512KHZ (( 130 << 22) | ( 2 << 12) | 15) ++#define CLK42X_SPEED_1536KHZ (( 43 << 22) | ( 18 << 12) | 47) ++#define CLK42X_SPEED_1544KHZ (( 43 << 22) | ( 33 << 12) | 192) ++#define CLK42X_SPEED_2048KHZ (( 32 << 22) | ( 34 << 12) | 63) ++#define CLK42X_SPEED_4096KHZ (( 16 << 22) | ( 34 << 12) | 127) ++#define CLK42X_SPEED_8192KHZ (( 8 << 22) | ( 34 << 12) | 255) ++ ++#define CLK46X_SPEED_512KHZ (( 130 << 22) | ( 24 << 12) | 127) ++#define CLK46X_SPEED_1536KHZ (( 43 << 22) | (152 << 12) | 383) ++#define CLK46X_SPEED_1544KHZ (( 43 << 22) | ( 66 << 12) | 385) ++#define CLK46X_SPEED_2048KHZ (( 32 << 22) | (280 << 12) | 511) ++#define CLK46X_SPEED_4096KHZ (( 16 << 22) | (280 << 12) | 1023) ++#define CLK46X_SPEED_8192KHZ (( 8 << 22) | (280 << 12) | 2047) ++ ++ ++/* hss_config, LUT entries */ ++#define TDMMAP_UNASSIGNED 0 ++#define TDMMAP_HDLC 1 /* HDLC - packetized */ ++#define TDMMAP_VOICE56K 2 /* Voice56K - 7-bit channelized */ ++#define TDMMAP_VOICE64K 3 /* Voice64K - 8-bit channelized */ ++ ++/* offsets into HSS config */ ++#define HSS_CONFIG_TX_PCR 0x00 /* port configuration registers */ ++#define HSS_CONFIG_RX_PCR 0x04 ++#define HSS_CONFIG_CORE_CR 0x08 /* loopback control, HSS# */ ++#define HSS_CONFIG_CLOCK_CR 0x0C /* clock generator control */ ++#define HSS_CONFIG_TX_FCR 0x10 /* frame configuration registers */ ++#define HSS_CONFIG_RX_FCR 0x14 ++#define HSS_CONFIG_TX_LUT 0x18 /* channel look-up tables */ ++#define HSS_CONFIG_RX_LUT 0x38 ++ ++ ++/* NPE command codes */ ++/* writes the ConfigWord value to the location specified by offset */ ++#define PORT_CONFIG_WRITE 0x40 ++ ++/* triggers the NPE to load the contents of the configuration table */ ++#define PORT_CONFIG_LOAD 0x41 ++ ++/* triggers the NPE to return an HssErrorReadResponse message */ ++#define PORT_ERROR_READ 0x42 ++ ++/* reset NPE internal status and enable the HssChannelized operation */ ++#define CHAN_FLOW_ENABLE 0x43 ++#define CHAN_FLOW_DISABLE 0x44 ++#define CHAN_IDLE_PATTERN_WRITE 0x45 ++#define CHAN_NUM_CHANS_WRITE 0x46 ++#define CHAN_RX_BUF_ADDR_WRITE 0x47 ++#define CHAN_RX_BUF_CFG_WRITE 0x48 ++#define CHAN_TX_BLK_CFG_WRITE 0x49 ++#define CHAN_TX_BUF_ADDR_WRITE 0x4A ++#define CHAN_TX_BUF_SIZE_WRITE 0x4B ++#define CHAN_TSLOTSWITCH_ENABLE 0x4C ++#define CHAN_TSLOTSWITCH_DISABLE 0x4D ++ ++/* downloads the gainWord value for a timeslot switching channel associated ++ with bypassNum */ ++#define CHAN_TSLOTSWITCH_GCT_DOWNLOAD 0x4E ++ ++/* triggers the NPE to reset internal status and enable the HssPacketized ++ operation for the flow specified by pPipe */ ++#define PKT_PIPE_FLOW_ENABLE 0x50 ++#define PKT_PIPE_FLOW_DISABLE 0x51 ++#define PKT_NUM_PIPES_WRITE 0x52 ++#define PKT_PIPE_FIFO_SIZEW_WRITE 0x53 ++#define PKT_PIPE_HDLC_CFG_WRITE 0x54 ++#define PKT_PIPE_IDLE_PATTERN_WRITE 0x55 ++#define PKT_PIPE_RX_SIZE_WRITE 0x56 ++#define PKT_PIPE_MODE_WRITE 0x57 ++ ++/* HDLC packet status values - desc->status */ ++#define ERR_SHUTDOWN 1 /* stop or shutdown occurrance */ ++#define ERR_HDLC_ALIGN 2 /* HDLC alignment error */ ++#define ERR_HDLC_FCS 3 /* HDLC Frame Check Sum error */ ++#define ERR_RXFREE_Q_EMPTY 4 /* RX-free queue became empty while receiving ++ this packet (if buf_len < pkt_len) */ ++#define ERR_HDLC_TOO_LONG 5 /* HDLC frame size too long */ ++#define ERR_HDLC_ABORT 6 /* abort sequence received */ ++#define ERR_DISCONNECTING 7 /* disconnect is in progress */ ++ ++#define CLOCK_EXT 0 ++#define CLOCK_INT 1 ++ ++enum mode {MODE_HDLC = 0, MODE_RAW, MODE_G704}; ++enum rx_tx_bit { ++ TX_BIT = 0, ++ RX_BIT = 1 ++}; ++enum chan_bit { ++ CHAN_0 = (1 << 0), ++ CHAN_1 = (1 << 1), ++ CHAN_2 = (1 << 2), ++ CHAN_3 = (1 << 3), ++ CHAN_4 = (1 << 4), ++ CHAN_5 = (1 << 5), ++ CHAN_6 = (1 << 6), ++ CHAN_7 = (1 << 7), ++ CHAN_8 = (1 << 8), ++ CHAN_9 = (1 << 9), ++ CHAN_10 = (1 << 10), ++ CHAN_11 = (1 << 11), ++ CHAN_12 = (1 << 12), ++ CHAN_13 = (1 << 13), ++ CHAN_14 = (1 << 14), ++ CHAN_15 = (1 << 15) ++}; ++ ++enum alignment { NOT_ALIGNED = 0, EVEN_FIRST, ODD_FIRST }; ++ ++#ifdef __ARMEB__ ++typedef struct sk_buff buffer_t; ++#define free_buffer dev_kfree_skb ++#define free_buffer_irq dev_kfree_skb_irq ++#else ++typedef void buffer_t; ++#define free_buffer kfree ++#define free_buffer_irq kfree ++#endif ++ ++struct hss_device { ++ struct port *port; ++ unsigned int open_count, excl_open; ++ unsigned long tx_loc, rx_loc; /* bytes */ ++ unsigned long tx_frame, rx_frame; /* Frames */ ++ u8 id, chan_count; ++ u8 log_channels[MAX_CHANNELS]; ++ ++ u8 *rx_buf; ++ u8 *tx_buf; ++ ++ size_t rx_buffer_size; ++ size_t rx_period_size; ++ size_t tx_buffer_size; ++ size_t tx_period_size; ++ ++ void (*rx_callback)(void *data); ++ void *rx_data; ++ void (*tx_callback)(void *data); ++ void *tx_data; ++ void *private_data; ++}; ++ ++extern struct hss_device *hss_handle[32]; ++extern struct port *hss_port[2]; ++ ++struct port { ++ unsigned char init; ++ ++ struct device *dev; ++ ++ struct tasklet_struct task; ++ unsigned int id; ++ unsigned long chan_rx_bitmap; ++ unsigned long chan_tx_bitmap; ++ unsigned char chan_open; ++ ++ /* the following fields must be protected by npe_lock */ ++ enum mode mode; ++ unsigned int clock_type, clock_rate, loopback; ++ unsigned int frame_size, frame_sync_offset; ++ unsigned int next_rx_frame; ++ ++ struct hss_device *chan_devices[MAX_CHAN_DEVICES]; ++ u32 chan_tx_buf_phys, chan_rx_buf_phys; ++ u32 chan_tx_pointers_phys; ++ u32 *chan_tx_pointers; ++ u8 *chan_rx_buf; ++ u8 *chan_tx_buf; ++ u8 *tx_lists[CHAN_TX_LISTS][8]; ++ u8 *rx_frames[8][CHAN_TX_LISTS]; ++ unsigned int chan_open_count, hdlc_open; ++ unsigned int chan_started, initialized, just_set_offset; ++ unsigned int chan_last_rx, chan_last_tx; ++ ++ /* assigned channels, may be invalid with given frame length or mode */ ++ u8 channels[MAX_CHANNELS]; ++ int msg_count; ++}; ++ ++/* NPE message structure */ ++struct msg { ++#ifdef __ARMEB__ ++ u8 cmd, unused, hss_port, index; ++ union { ++ struct { u8 data8a, data8b, data8c, data8d; }; ++ struct { u16 data16a, data16b; }; ++ struct { u32 data32; }; ++ }; ++#else ++ u8 index, hss_port, unused, cmd; ++ union { ++ struct { u8 data8d, data8c, data8b, data8a; }; ++ struct { u16 data16b, data16a; }; ++ struct { u32 data32; }; ++ }; ++#endif ++}; ++ ++#define rx_desc_phys(port, n) ((port)->desc_tab_phys + \ ++ (n) * sizeof(struct desc)) ++#define rx_desc_ptr(port, n) (&(port)->desc_tab[n]) ++ ++#define tx_desc_phys(port, n) ((port)->desc_tab_phys + \ ++ ((n) + RX_DESCS) * sizeof(struct desc)) ++#define tx_desc_ptr(port, n) (&(port)->desc_tab[(n) + RX_DESCS]) ++ ++int hss_prepare_chan(struct port *port); ++void hss_chan_stop(struct port *port); ++ ++struct hss_device *hss_init(int id, int channel); ++int hss_chan_open(struct hss_device *hdev); ++int hss_chan_close(struct hss_device *hdev); ++ ++int hss_set_tx_callback(struct hss_device *hdev, void (*tx_callback)(void *), void *tx_data); ++int hss_set_rx_callback(struct hss_device *hdev, void (*rx_callback)(void *), void *rx_data); ++int hss_tx_start(struct hss_device *hdev); ++int hss_tx_stop(struct hss_device *hdev); ++int hss_rx_start(struct hss_device *hdev); ++int hss_rx_stop(struct hss_device *hdev); ++ ++int hss_config_rx_dma(struct hss_device *hdev, void *buf, size_t buffer_size, size_t period_size); ++int hss_config_tx_dma(struct hss_device *hdev, void *buf, size_t buffer_size, size_t period_size); ++unsigned long hss_curr_offset_rx(struct hss_device *hdev); ++unsigned long hss_curr_offset_tx(struct hss_device *hdev); ++ diff --git a/target/linux/ixp4xx/patches-3.14/180-tw5334_support.patch b/target/linux/ixp4xx/patches-3.14/180-tw5334_support.patch new file mode 100644 index 0000000..b56fbb7 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/180-tw5334_support.patch @@ -0,0 +1,287 @@ +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -160,6 +160,14 @@ config ARCH_PRPMC1100 + PrPCM1100 Processor Mezanine Module. For more information on + this platform, see <file:Documentation/arm/IXP4xx>. + ++config MACH_TW5334 ++ bool "Titan Wireless TW-533-4" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the Titan ++ Wireless TW533-4. For more information on this platform, ++ see http://openwrt.org ++ + config MACH_NAS100D + bool + prompt "NAS100D" +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -24,6 +24,7 @@ obj-pci-$(CONFIG_MACH_SIDEWINDER) += sid + obj-pci-$(CONFIG_MACH_COMPEXWP18) += ixdp425-pci.o + obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o + obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o ++obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o + + obj-y += common.o + +@@ -49,6 +50,7 @@ obj-$(CONFIG_MACH_SIDEWINDER) += sidewin + obj-$(CONFIG_MACH_COMPEXWP18) += compex42x-setup.o + obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o + obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o ++obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h ++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h +@@ -44,7 +44,7 @@ static __inline__ void __arch_decomp_set + machine_is_gateway7001() || machine_is_wg302v2() || + machine_is_devixp() || machine_is_miccpt() || machine_is_mic256() || + machine_is_pronghorn() || machine_is_pronghorn_metro() || +- machine_is_wrt300nv2()) ++ machine_is_wrt300nv2() || machine_is_tw5334()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/tw5334-pci.c +@@ -0,0 +1,68 @@ ++/* ++ * arch/arch/mach-ixp4xx/tw5334-pci.c ++ * ++ * PCI setup routines for the Titan Wireless TW-533-4 ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Imre Kaloz <kaloz@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++ ++#include <asm/mach/pci.h> ++ ++void __init tw5334_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO2, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO0, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init tw5334_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 12) ++ return IRQ_IXP4XX_GPIO6; ++ else if (slot == 13) ++ return IRQ_IXP4XX_GPIO2; ++ else if (slot == 14) ++ return IRQ_IXP4XX_GPIO1; ++ else if (slot == 15) ++ return IRQ_IXP4XX_GPIO0; ++ else return -1; ++} ++ ++struct hw_pci tw5334_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = tw5334_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = tw5334_map_irq, ++}; ++ ++int __init tw5334_pci_init(void) ++{ ++ if (machine_is_tw5334()) ++ pci_common_init(&tw5334_pci); ++ return 0; ++} ++ ++subsys_initcall(tw5334_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/tw5334-setup.c +@@ -0,0 +1,167 @@ ++/* ++ * arch/arm/mach-ixp4xx/tw5334-setup.c ++ * ++ * Board setup for the Titan Wireless TW-533-4 ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/if_ether.h> ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++ ++#include <asm/types.h> ++#include <asm/setup.h> ++#include <asm/memory.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data tw5334_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource tw5334_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device tw5334_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &tw5334_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &tw5334_flash_resource, ++}; ++ ++static struct resource tw5334_uart_resource = { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct plat_serial8250_port tw5334_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device tw5334_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = tw5334_uart_data, ++ }, ++ .num_resources = 1, ++ .resource = &tw5334_uart_resource, ++}; ++ ++/* Built-in 10/100 Ethernet MAC interfaces */ ++static struct eth_plat_info tw5334_plat_eth[] = { ++ { ++ .phy = 0, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 1, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device tw5334_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = tw5334_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = tw5334_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct platform_device *tw5334_devices[] __initdata = { ++ &tw5334_flash, ++ &tw5334_uart, ++ &tw5334_eth[0], ++ &tw5334_eth[1], ++}; ++ ++static void __init tw5334_init(void) ++{ ++ uint8_t __iomem *f; ++ int i; ++ ++ ixp4xx_sys_init(); ++ ++ tw5334_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ tw5334_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(tw5334_devices, ARRAY_SIZE(tw5334_devices)); ++ ++ /* ++ * Map in a portion of the flash and read the MAC addresses. ++ * Since it is stored in BE in the flash itself, we need to ++ * byteswap it if we're in LE mode. ++ */ ++ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x1000000); ++ if (f) { ++ for (i = 0; i < 6; i++) { ++#ifdef __ARMEB__ ++ tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + i); ++ tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + i); ++#else ++ tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + (i^3)); ++ tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + (i^3)); ++#endif ++ } ++ iounmap(f); ++ } ++ ++ printk(KERN_INFO "TW-533-4: Using MAC address %pM for port 0\n", ++ tw5334_plat_eth[0].hwaddr); ++ printk(KERN_INFO "TW-533-4: Using MAC address %pM for port 1\n", ++ tw5334_plat_eth[1].hwaddr); ++} ++ ++#ifdef CONFIG_MACH_TW5334 ++MACHINE_START(TW5334, "Titan Wireless TW-533-4") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = tw5334_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++#endif diff --git a/target/linux/ixp4xx/patches-3.14/185-mi424wr_support.patch b/target/linux/ixp4xx/patches-3.14/185-mi424wr_support.patch new file mode 100644 index 0000000..81713b3 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/185-mi424wr_support.patch @@ -0,0 +1,507 @@ +--- a/arch/arm/configs/ixp4xx_defconfig ++++ b/arch/arm/configs/ixp4xx_defconfig +@@ -26,6 +26,7 @@ CONFIG_MACH_NAS100D=y + CONFIG_MACH_DSMG600=y + CONFIG_MACH_FSG=y + CONFIG_MACH_GTWX5715=y ++CONFIG_MACH_MI424WR=y + CONFIG_IXP4XX_QMGR=y + CONFIG_IXP4XX_NPE=y + # CONFIG_ARM_THUMB is not set +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -258,6 +258,13 @@ config MACH_MIC256 + Say 'Y' here if you want your kernel to support the MIC256 + board from OMICRON electronics GmbH. + ++config MACH_MI424WR ++ bool "Actiontec MI424WR" ++ depends on ARCH_IXP4XX ++ select PCI ++ help ++ Add support for the Actiontec MI424-WR. ++ + comment "IXP4xx Options" + + config IXP4XX_INDIRECT_PCI +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -25,6 +25,7 @@ obj-pci-$(CONFIG_MACH_COMPEXWP18) += ixd + obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o + obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o + obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o ++obj-pci-$(CONFIG_MACH_MI424WR) += mi424wr-pci.o + + obj-y += common.o + +@@ -51,6 +52,7 @@ obj-$(CONFIG_MACH_COMPEXWP18) += compex4 + obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o + obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o + obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o ++obj-$(CONFIG_MACH_MI424WR) += mi424wr-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/mi424wr-pci.c +@@ -0,0 +1,70 @@ ++/* ++ * arch/arm/mach-ixp4xx/mi424wr-pci.c ++ * ++ * Actiontec MI424WR board-level PCI initialization ++ * ++ * Copyright (C) 2008 Jose Vasconcellos ++ * ++ * Maintainer: Jose Vasconcellos <jvasco@verizon.net> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <asm/mach/pci.h> ++ ++/* PCI controller GPIO to IRQ pin mappings ++ * This information was obtained from Actiontec's GPL release. ++ * ++ * INTA INTB ++ * SLOT 13 8 6 ++ * SLOT 14 7 8 ++ * SLOT 15 6 7 ++ */ ++ ++void __init mi424wr_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init mi424wr_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 13) ++ return IRQ_IXP4XX_GPIO8; ++ if (slot == 14) ++ return IRQ_IXP4XX_GPIO7; ++ if (slot == 15) ++ return IRQ_IXP4XX_GPIO6; ++ ++ return -1; ++} ++ ++struct hw_pci mi424wr_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = mi424wr_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = mi424wr_map_irq, ++}; ++ ++int __init mi424wr_pci_init(void) ++{ ++ if (machine_is_mi424wr()) ++ pci_common_init(&mi424wr_pci); ++ return 0; ++} ++ ++subsys_initcall(mi424wr_pci_init); ++ +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/mi424wr-setup.c +@@ -0,0 +1,387 @@ ++/* ++ * arch/arm/mach-ixp4xx/mi424wr-setup.c ++ * ++ * Actiontec MI424-WR board setup ++ * Copyright (c) 2008 Jose Vasconcellos ++ * ++ * Based on Gemtek GTWX5715 by ++ * Copyright (C) 2004 George T. Joseph ++ * Derived from Coyote ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * as published by the Free Software Foundation; either version 2 ++ * of the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. ++ * ++ */ ++ ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/serial_8250.h> ++#include <linux/types.h> ++#include <linux/memory.h> ++#include <linux/leds.h> ++#include <linux/spi/spi_gpio_old.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/setup.h> ++#include <asm/system_info.h> ++#include <asm/irq.h> ++#include <asm/io.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++/* ++ * GPIO 2,3,4 and 9 are hard wired to the Micrel/Kendin KS8995M Switch ++ * and operate as an SPI type interface. The details of the interface ++ * are available on Kendin/Micrel's web site. ++ */ ++ ++#define MI424WR_KSSPI_SELECT 9 ++#define MI424WR_KSSPI_TXD 4 ++#define MI424WR_KSSPI_CLOCK 2 ++#define MI424WR_KSSPI_RXD 3 ++ ++/* ++ * The "reset" button is wired to GPIO 10. ++ * The GPIO is brought "low" when the button is pushed. ++ */ ++ ++#define MI424WR_BUTTON_GPIO 10 ++#define MI424WR_BUTTON_IRQ IRQ_IXP4XX_GPIO10 ++ ++#define MI424WR_MOCA_WAN_LED 11 ++ ++/* Latch on CS1 - taken from Actiontec's 2.4 source code ++ * ++ * default latch value ++ * 0 - power alarm led (red) 0 (off) ++ * 1 - power led (green) 0 (off) ++ * 2 - wireless led (green) 1 (off) ++ * 3 - no internet led (red) 0 (off) ++ * 4 - internet ok led (green) 0 (off) ++ * 5 - moca LAN 0 (off) ++ * 6 - WAN alarm led (red) 0 (off) ++ * 7 - PCI reset 1 (not reset) ++ * 8 - IP phone 1 led (green) 1 (off) ++ * 9 - IP phone 2 led (green) 1 (off) ++ * 10 - VOIP ready led (green) 1 (off) ++ * 11 - PSTN relay 1 control 0 (PSTN) ++ * 12 - PSTN relay 1 control 0 (PSTN) ++ * 13 - N/A ++ * 14 - N/A ++ * 15 - N/A ++ */ ++ ++#define MI424WR_LATCH_MASK 0x04 ++#define MI424WR_LATCH_DEFAULT 0x1f86 ++ ++#define MI424WR_LATCH_ALARM_LED 0x00 ++#define MI424WR_LATCH_POWER_LED 0x01 ++#define MI424WR_LATCH_WIRELESS_LED 0x02 ++#define MI424WR_LATCH_INET_DOWN_LED 0x03 ++#define MI424WR_LATCH_INET_OK_LED 0x04 ++#define MI424WR_LATCH_MOCA_LAN_LED 0x05 ++#define MI424WR_LATCH_WAN_ALARM_LED 0x06 ++#define MI424WR_LATCH_PCI_RESET 0x07 ++#define MI424WR_LATCH_PHONE1_LED 0x08 ++#define MI424WR_LATCH_PHONE2_LED 0x09 ++#define MI424WR_LATCH_VOIP_LED 0x10 ++#define MI424WR_LATCH_PSTN_RELAY1 0x11 ++#define MI424WR_LATCH_PSTN_RELAY2 0x12 ++ ++/* initialize CS1 to default timings, Intel style, 16-bit bus */ ++#define MI424WR_CS1_CONFIG 0x80000002 ++ ++/* Define both UARTs but they are not easily accessible. ++ */ ++ ++static struct resource mi424wr_uart_resources[] = { ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++ } ++}; ++ ++ ++static struct plat_serial8250_port mi424wr_uart_platform_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device mi424wr_uart_device = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev.platform_data = mi424wr_uart_platform_data, ++ .num_resources = ARRAY_SIZE(mi424wr_uart_resources), ++ .resource = mi424wr_uart_resources, ++}; ++ ++static struct flash_platform_data mi424wr_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource mi424wr_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device mi424wr_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev.platform_data = &mi424wr_flash_data, ++ .num_resources = 1, ++ .resource = &mi424wr_flash_resource, ++}; ++ ++static int mi424wr_spi_boardinfo_setup(struct spi_board_info *bi, ++ struct spi_master *master, void *data) ++{ ++ ++ strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias)); ++ ++ bi->max_speed_hz = 5000000 /* Hz */; ++ bi->bus_num = master->bus_num; ++ bi->mode = SPI_MODE_0; ++ ++ return 0; ++} ++ ++static struct spi_gpio_platform_data mi424wr_spi_bus_data = { ++ .pin_cs = MI424WR_KSSPI_SELECT, ++ .pin_clk = MI424WR_KSSPI_CLOCK, ++ .pin_miso = MI424WR_KSSPI_RXD, ++ .pin_mosi = MI424WR_KSSPI_TXD, ++ .cs_activelow = 1, ++ .no_spi_delay = 1, ++ .boardinfo_setup = mi424wr_spi_boardinfo_setup, ++}; ++ ++static struct gpio_led mi424wr_gpio_led[] = { ++ { ++ .name = "moca-wan", /* green led */ ++ .gpio = MI424WR_MOCA_WAN_LED, ++ .active_low = 0, ++ } ++}; ++ ++static struct gpio_led_platform_data mi424wr_gpio_leds_data = { ++ .num_leds = 1, ++ .leds = mi424wr_gpio_led, ++}; ++ ++static struct platform_device mi424wr_gpio_leds = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev.platform_data = &mi424wr_gpio_leds_data, ++}; ++ ++static uint16_t latch_value = MI424WR_LATCH_DEFAULT; ++static uint16_t __iomem *iobase; ++ ++static void mi424wr_latch_set_led(u8 bit, enum led_brightness value) ++{ ++ ++ if (((MI424WR_LATCH_MASK >> bit) & 1) ^ (value == LED_OFF)) ++ latch_value &= ~(0x1 << bit); ++ else ++ latch_value |= (0x1 << bit); ++ ++ __raw_writew(latch_value, iobase); ++ ++} ++ ++static struct latch_led mi424wr_latch_led[] = { ++ { ++ .name = "power-alarm", ++ .bit = MI424WR_LATCH_ALARM_LED, ++ }, ++ { ++ .name = "power-ok", ++ .bit = MI424WR_LATCH_POWER_LED, ++ }, ++ { ++ .name = "wireless", /* green led */ ++ .bit = MI424WR_LATCH_WIRELESS_LED, ++ }, ++ { ++ .name = "inet-down", /* red led */ ++ .bit = MI424WR_LATCH_INET_DOWN_LED, ++ }, ++ { ++ .name = "inet-up", /* green led */ ++ .bit = MI424WR_LATCH_INET_OK_LED, ++ }, ++ { ++ .name = "moca-lan", /* green led */ ++ .bit = MI424WR_LATCH_MOCA_LAN_LED, ++ }, ++ { ++ .name = "wan-alarm", /* red led */ ++ .bit = MI424WR_LATCH_WAN_ALARM_LED, ++ } ++}; ++ ++static struct latch_led_platform_data mi424wr_latch_leds_data = { ++ .num_leds = ARRAY_SIZE(mi424wr_latch_led), ++ .mem = 0x51000000, ++ .leds = mi424wr_latch_led, ++ .set_led = mi424wr_latch_set_led, ++}; ++ ++static struct platform_device mi424wr_latch_leds = { ++ .name = "leds-latch", ++ .id = -1, ++ .dev.platform_data = &mi424wr_latch_leds_data, ++}; ++ ++static struct platform_device mi424wr_spi_bus = { ++ .name = "spi-gpio", ++ .id = 0, ++ .dev.platform_data = &mi424wr_spi_bus_data, ++}; ++ ++static struct eth_plat_info mi424wr_wan_data = { ++ .phy = 17, /* KS8721 */ ++ .rxq = 3, ++ .txreadyq = 20, ++}; ++ ++static struct eth_plat_info mi424wr_lan_data = { ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0x1e, /* ports 1-4 of the KS8995 switch */ ++ .rxq = 4, ++ .txreadyq = 21, ++}; ++ ++static struct platform_device mi424wr_npe_devices[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = &mi424wr_lan_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = &mi424wr_wan_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct eth_plat_info mi424wr_wanD_data = { ++ .phy = 5, ++ .rxq = 4, ++ .txreadyq = 21, ++}; ++ ++static struct eth_plat_info mi424wr_lanD_data = { ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0x1e, /* ports 1-4 of the KS8995 switch */ ++ .rxq = 3, ++ .txreadyq = 20, ++}; ++ ++static struct platform_device mi424wr_npeD_devices[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = &mi424wr_lanD_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = &mi424wr_wanD_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct platform_device *mi424wr_devices[] __initdata = { ++ &mi424wr_uart_device, ++ &mi424wr_flash, ++ &mi424wr_gpio_leds, ++ &mi424wr_latch_leds, ++ &mi424wr_spi_bus, ++}; ++ ++static void __init mi424wr_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ mi424wr_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ mi424wr_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_8M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = MI424WR_CS1_CONFIG; ++ ++ /* configure button as input ++ */ ++ gpio_line_config(MI424WR_BUTTON_GPIO, IXP4XX_GPIO_IN); ++ ++ /* Initialize LEDs and enables PCI bus. ++ */ ++ iobase = ioremap_nocache(IXP4XX_EXP_BUS_BASE(1), 0x1000); ++ __raw_writew(latch_value, iobase); ++ ++ platform_add_devices(mi424wr_devices, ARRAY_SIZE(mi424wr_devices)); ++ ++ /* Need to figure out how to detect revD. ++ * Look for a revision argument sent by redboot. ++ */ ++#define revD 4 ++ if (system_rev == revD) { ++ platform_device_register(&mi424wr_npeD_devices[0]); ++ platform_device_register(&mi424wr_npeD_devices[1]); ++ } else { ++ platform_device_register(&mi424wr_npe_devices[0]); ++ platform_device_register(&mi424wr_npe_devices[1]); ++ } ++} ++ ++ ++MACHINE_START(MI424WR, "Actiontec MI424WR") ++ /* Maintainer: Jose Vasconcellos */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = mi424wr_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++ diff --git a/target/linux/ixp4xx/patches-3.14/190-cambria_support.patch b/target/linux/ixp4xx/patches-3.14/190-cambria_support.patch new file mode 100644 index 0000000..fb68857 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/190-cambria_support.patch @@ -0,0 +1,1139 @@ +Index: linux-3.14.25/arch/arm/mach-ixp4xx/Kconfig +=================================================================== +--- linux-3.14.25.orig/arch/arm/mach-ixp4xx/Kconfig 2014-11-30 15:26:41.488079161 +0100 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/Kconfig 2014-12-01 07:28:47.406514014 +0100 +@@ -21,6 +21,14 @@ + Avila Network Platform. For more information on this platform, + see <file:Documentation/arm/IXP4xx>. + ++config MACH_CAMBRIA ++ bool "Cambria" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the Gateworks ++ Cambria series. For more information on this platform, ++ see <file:Documentation/arm/IXP4xx>. ++ + config MACH_LOFT + bool "Loft" + depends on MACH_AVILA +@@ -218,7 +226,7 @@ + + config CPU_IXP43X + bool +- depends on MACH_KIXRP435 ++ depends on MACH_KIXRP435 || MACH_CAMBRIA + default y + + config MACH_GTWX5715 +Index: linux-3.14.25/arch/arm/mach-ixp4xx/Makefile +=================================================================== +--- linux-3.14.25.orig/arch/arm/mach-ixp4xx/Makefile 2014-11-30 15:26:41.488079161 +0100 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/Makefile 2014-12-01 07:28:47.406514014 +0100 +@@ -7,6 +7,7 @@ + + obj-pci-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o + obj-pci-$(CONFIG_MACH_AVILA) += avila-pci.o ++obj-pci-$(CONFIG_MACH_CAMBRIA) += cambria-pci.o + obj-pci-$(CONFIG_MACH_IXDPG425) += ixdpg425-pci.o + obj-pci-$(CONFIG_ARCH_ADI_COYOTE) += coyote-pci.o + obj-pci-$(CONFIG_MACH_GTWX5715) += gtwx5715-pci.o +@@ -31,6 +32,7 @@ + + obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-setup.o + obj-$(CONFIG_MACH_AVILA) += avila-setup.o ++obj-$(CONFIG_MACH_CAMBRIA) += cambria-setup.o + obj-$(CONFIG_MACH_IXDPG425) += coyote-setup.o + obj-$(CONFIG_ARCH_ADI_COYOTE) += coyote-setup.o + obj-$(CONFIG_MACH_GTWX5715) += gtwx5715-setup.o +Index: linux-3.14.25/arch/arm/mach-ixp4xx/cambria-pci.c +=================================================================== +--- /dev/null 1970-01-01 00:00:00.000000000 +0000 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/cambria-pci.c 2014-11-30 15:26:41.728087272 +0100 +@@ -0,0 +1,78 @@ ++/* ++ * arch/arch/mach-ixp4xx/cambria-pci.c ++ * ++ * PCI setup routines for Gateworks Cambria series ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Imre Kaloz <kaloz@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++ ++#include <asm/mach/pci.h> ++ ++extern void ixp4xx_pci_preinit(void); ++extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); ++extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys); ++ ++void __init cambria_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init cambria_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 1) ++ return IRQ_IXP4XX_GPIO11; ++ else if (slot == 2) ++ return IRQ_IXP4XX_GPIO10; ++ else if (slot == 3) ++ return IRQ_IXP4XX_GPIO9; ++ else if (slot == 4) ++ return IRQ_IXP4XX_GPIO8; ++ else if (slot == 6) ++ return IRQ_IXP4XX_GPIO10; ++ else if (slot == 15) ++ return IRQ_IXP4XX_GPIO8; ++ ++ else return -1; ++} ++ ++struct hw_pci cambria_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = cambria_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = cambria_map_irq, ++}; ++ ++int __init cambria_pci_init(void) ++{ ++ if (machine_is_cambria()) ++ pci_common_init(&cambria_pci); ++ return 0; ++} ++ ++subsys_initcall(cambria_pci_init); +Index: linux-3.14.25/arch/arm/mach-ixp4xx/cambria-setup.c +=================================================================== +--- /dev/null 1970-01-01 00:00:00.000000000 +0000 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/cambria-setup.c 2014-11-30 16:06:45.622389213 +0100 +@@ -0,0 +1,1003 @@ ++/* ++ * arch/arm/mach-ixp4xx/cambria-setup.c ++ * ++ * Board setup for the Gateworks Cambria series ++ * ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * Copyright (C) 2012 Gateworks Corporation <support@gateworks.com> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <kaloz@openwrt.org> ++ * Tim Harvey <tharvey@gateworks.com> ++ */ ++ ++#include <linux/device.h> ++#include <linux/gpio_keys.h> ++#include <linux/gpio.h> ++#include <linux/i2c.h> ++#include <linux/i2c-gpio.h> ++#include <linux/platform_data/at24.h> ++#include <linux/i2c/gw_i2c_pld.h> ++#include <linux/platform_data/pca953x.h> ++#include <linux/if_ether.h> ++#include <linux/init.h> ++#include <linux/input.h> ++#include <linux/kernel.h> ++#include <linux/leds.h> ++#include <linux/memory.h> ++#include <linux/netdevice.h> ++#include <linux/serial.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++#include <linux/socket.h> ++#include <linux/types.h> ++#include <linux/tty.h> ++#include <linux/irq.h> ++#include <linux/usb/ehci_pdriver.h> ++ ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++#include <asm/setup.h> ++ ++#define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x) ++ ++struct cambria_board_info { ++ unsigned char *model; ++ void (*setup)(void); ++}; ++ ++static struct cambria_board_info *cambria_info __initdata; ++ ++static struct flash_platform_data cambria_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource cambria_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device cambria_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &cambria_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &cambria_flash_resource, ++}; ++ ++static struct i2c_gpio_platform_data cambria_i2c_gpio_data = { ++ .sda_pin = 7, ++ .scl_pin = 6, ++}; ++ ++static struct platform_device cambria_i2c_gpio = { ++ .name = "i2c-gpio", ++ .id = 0, ++ .dev = { ++ .platform_data = &cambria_i2c_gpio_data, ++ }, ++}; ++ ++#ifdef SFP_SERIALID ++static struct i2c_gpio_platform_data cambria_i2c_gpio_sfpa_data = { ++ .sda_pin = 113, ++ .scl_pin = 112, ++ .sda_is_open_drain = 0, ++ .scl_is_open_drain = 0, ++}; ++ ++static struct platform_device cambria_i2c_gpio_sfpa = { ++ .name = "i2c-gpio", ++ .id = 1, ++ .dev = { ++ .platform_data = &cambria_i2c_gpio_sfpa_data, ++ }, ++}; ++ ++static struct i2c_gpio_platform_data cambria_i2c_gpio_sfpb_data = { ++ .sda_pin = 115, ++ .scl_pin = 114, ++ .sda_is_open_drain = 0, ++ .scl_is_open_drain = 0, ++}; ++ ++static struct platform_device cambria_i2c_gpio_sfpb = { ++ .name = "i2c-gpio", ++ .id = 2, ++ .dev = { ++ .platform_data = &cambria_i2c_gpio_sfpb_data, ++ }, ++}; ++#endif // #ifdef SFP_SERIALID ++ ++static struct eth_plat_info cambria_npec_data = { ++ .phy = 1, ++ .rxq = 4, ++ .txreadyq = 21, ++}; ++ ++static struct eth_plat_info cambria_npea_data = { ++ .phy = 2, ++ .rxq = 2, ++ .txreadyq = 19, ++}; ++ ++static struct platform_device cambria_npec_device = { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = &cambria_npec_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++}; ++ ++static struct platform_device cambria_npea_device = { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEA, ++ .dev.platform_data = &cambria_npea_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++}; ++ ++static struct resource cambria_uart_resource = { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct plat_serial8250_port cambria_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device cambria_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = cambria_uart_data, ++ }, ++ .num_resources = 1, ++ .resource = &cambria_uart_resource, ++}; ++ ++static struct resource cambria_optional_uart_resources[] = { ++ { ++ .start = 0x52000000, ++ .end = 0x52000fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = 0x53000000, ++ .end = 0x53000fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = 0x52000000, ++ .end = 0x52000fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = 0x52000000, ++ .end = 0x52000fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = 0x52000000, ++ .end = 0x52000fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = 0x52000000, ++ .end = 0x52000fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = 0x52000000, ++ .end = 0x52000fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = 0x53000000, ++ .end = 0x53000fff, ++ .flags = IORESOURCE_MEM ++ } ++}; ++ ++static struct plat_serial8250_port cambria_optional_uart_data[] = { ++ { ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM_DELAY, ++ .regshift = 0, ++ .uartclk = 1843200, ++ .rw_delay = 10, ++ }, ++ { ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM_DELAY, ++ .regshift = 0, ++ .uartclk = 1843200, ++ .rw_delay = 10, ++ }, ++ { ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ }, ++ { ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ }, ++ { ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ }, ++ { ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ }, ++ { ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ }, ++ { }, ++}; ++ ++static struct platform_device cambria_optional_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM1, ++ .dev.platform_data = cambria_optional_uart_data, ++ .num_resources = 2, ++ .resource = cambria_optional_uart_resources, ++}; ++ ++static struct resource cambria_pata_resources[] = { ++ { ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .name = "intrq", ++ .start = IRQ_IXP4XX_GPIO12, ++ .end = IRQ_IXP4XX_GPIO12, ++ .flags = IORESOURCE_IRQ, ++ }, ++}; ++ ++static struct ixp4xx_pata_data cambria_pata_data = { ++ .cs0_bits = 0xbfff3c03, ++ .cs1_bits = 0xbfff3c03, ++}; ++ ++static struct platform_device cambria_pata = { ++ .name = "pata_ixp4xx_cf", ++ .id = 0, ++ .dev.platform_data = &cambria_pata_data, ++ .num_resources = ARRAY_SIZE(cambria_pata_resources), ++ .resource = cambria_pata_resources, ++}; ++ ++static struct gpio_led cambria_gpio_leds[] = { ++ { ++ .name = "user", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "user2", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "user3", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "user4", ++ .gpio = 0, ++ .active_low = 1, ++ } ++}; ++ ++static struct gpio_led_platform_data cambria_gpio_leds_data = { ++ .num_leds = 1, ++ .leds = cambria_gpio_leds, ++}; ++ ++static struct platform_device cambria_gpio_leds_device = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev.platform_data = &cambria_gpio_leds_data, ++}; ++ ++static struct resource cambria_gpio_resources[] = { ++ { ++ .name = "gpio", ++ .flags = 0, ++ }, ++}; ++ ++static struct gpio cambria_gpios_gw2350[] = { ++ // ARM GPIO ++#if 0 // configured from bootloader ++ { 0, GPIOF_IN, "ARM_DIO0" }, ++ { 1, GPIOF_IN, "ARM_DIO1" }, ++ { 2, GPIOF_IN, "ARM_DIO2" }, ++ { 3, GPIOF_IN, "ARM_DIO3" }, ++ { 4, GPIOF_IN, "ARM_DIO4" }, ++ { 5, GPIOF_IN, "ARM_DIO5" }, ++ { 12, GPIOF_OUT_INIT_HIGH, "WDOGEN#" }, ++#endif ++ { 8, GPIOF_IN, "ARM_DIO8" }, ++ { 9, GPIOF_IN, "ARM_DIO9" }, ++}; ++ ++static struct gpio cambria_gpios_gw2358[] = { ++ // ARM GPIO ++#if 0 // configured from bootloader ++ { 0, GPIOF_IN, "*VINLOW#" }, ++ { 2, GPIOF_IN, "*GPS_PPS" }, ++ { 3, GPIOF_IN, "*GPS_IRQ#" }, ++ { 4, GPIOF_IN, "*RS485_IRQ#" }, ++ { 5, GPIOF_IN, "*SER_EN#" }, ++ { 14, GPIOF_OUT_INIT_HIGH, "*WDOGEN#" }, ++#endif ++}; ++ ++static struct gpio cambria_gpios_gw2359[] = { ++ // ARM GPIO ++#if 0 // configured from bootloader ++ { 0, GPIOF_IN, "*PCA_IRQ#" }, ++ { 1, GPIOF_IN, "ARM_DIO1" }, ++ { 2, GPIOF_IN, "ARM_DIO2" }, ++ { 3, GPIOF_IN, "ARM_DIO3" }, ++ { 4, GPIOF_IN, "ARM_DIO4" }, ++ { 5, GPIOF_IN, "ARM_DIO5" }, ++ { 8, GPIOF_OUT_INIT_HIGH, "*WDOGEN#" }, ++#endif ++ { 11, GPIOF_OUT_INIT_HIGH, "*SER_EN" }, // console serial enable ++ { 12, GPIOF_IN, "*GSC_IRQ#" }, ++ { 13, GPIOF_OUT_INIT_HIGH, "*PCIE_RST#"}, ++ // GSC GPIO ++#if !(IS_ENABLED(CONFIG_KEYBOARD_GPIO_POLLED)) ++ {100, GPIOF_IN, "*USER_PB#" }, ++#endif ++ {103, GPIOF_OUT_INIT_HIGH, "*5V_EN" }, // 5V aux supply enable ++ {108, GPIOF_IN, "*SMUXDA0" }, ++ {109, GPIOF_IN, "*SMUXDA1" }, ++ {110, GPIOF_IN, "*SMUXDA2" }, ++ {111, GPIOF_IN, "*SMUXDB0" }, ++ {112, GPIOF_IN, "*SMUXDB1" }, ++ {113, GPIOF_IN, "*SMUXDB2" }, ++ // PCA GPIO ++ {118, GPIOF_IN, "*USIM2_DET#"}, // USIM2 Detect ++ {120, GPIOF_OUT_INIT_LOW, "*USB1_PCI_SEL"}, // USB1 Select (1=PCI, 0=FP) ++ {121, GPIOF_OUT_INIT_LOW, "*USB2_PCI_SEL"}, // USB2 Select (1=PCI, 0=FP) ++ {122, GPIOF_IN, "*USIM1_DET#"}, // USIM1 Detect ++ {123, GPIOF_OUT_INIT_HIGH, "*COM1_DTR#" }, // J21/J10 ++ {124, GPIOF_IN, "*COM1_DSR#" }, // J21/J10 ++ {127, GPIOF_IN, "PCA_DIO0" }, ++ {128, GPIOF_IN, "PCA_DIO1" }, ++ {129, GPIOF_IN, "PCA_DIO2" }, ++ {130, GPIOF_IN, "PCA_DIO3" }, ++ {131, GPIOF_IN, "PCA_DIO4" }, ++}; ++ ++static struct gpio cambria_gpios_gw2360[] = { ++ // ARM GPIO ++ { 0, GPIOF_IN, "*PCA_IRQ#" }, ++ { 11, GPIOF_OUT_INIT_LOW, "*SER0_EN#" }, ++ { 12, GPIOF_IN, "*GSC_IRQ#" }, ++ { 13, GPIOF_OUT_INIT_HIGH, "*PCIE_RST#"}, ++ // GSC GPIO ++#if !(IS_ENABLED(CONFIG_KEYBOARD_GPIO_POLLED)) ++ {100, GPIOF_IN, "*USER_PB#" }, ++#endif ++ {108, GPIOF_OUT_INIT_LOW, "*ENET1_EN#" }, // ENET1 TX Enable ++ {109, GPIOF_IN, "*ENET1_PRES#" }, // ENET1 Detect (0=SFP present) ++ {110, GPIOF_OUT_INIT_LOW, "*ENET2_EN#" }, // ENET2 TX Enable ++ {111, GPIOF_IN, "*ENET2_PRES#"}, // ENET2 Detect (0=SFP present) ++ // PCA GPIO ++ {116, GPIOF_OUT_INIT_HIGH, "*USIM2_LOC"}, // USIM2 Select (1=Loc, 0=Rem) ++ {117, GPIOF_IN, "*USIM2_DET_LOC#" },// USIM2 Detect (Local Slot) ++ {118, GPIOF_IN, "*USIM2_DET_REM#" },// USIM2 Detect (Remote Slot) ++ {120, GPIOF_OUT_INIT_LOW, "*USB1_PCI_SEL"}, // USB1 Select (1=PCIe1, 0=J1) ++ {121, GPIOF_OUT_INIT_LOW, "*USB2_PCI_SEL"}, // USB2 Select (1=PCIe2, 0=J1) ++ {122, GPIOF_IN, "*USIM1_DET#"}, // USIM1 Detect ++ {127, GPIOF_IN, "DIO0" }, ++ {128, GPIOF_IN, "DIO1" }, ++ {129, GPIOF_IN, "DIO2" }, ++ {130, GPIOF_IN, "DIO3" }, ++ {131, GPIOF_IN, "DIO4" }, ++}; ++ ++static struct latch_led cambria_latch_leds[] = { ++ { ++ .name = "ledA", /* green led */ ++ .bit = 0, ++ }, ++ { ++ .name = "ledB", /* green led */ ++ .bit = 1, ++ }, ++ { ++ .name = "ledC", /* green led */ ++ .bit = 2, ++ }, ++ { ++ .name = "ledD", /* green led */ ++ .bit = 3, ++ }, ++ { ++ .name = "ledE", /* green led */ ++ .bit = 4, ++ }, ++ { ++ .name = "ledF", /* green led */ ++ .bit = 5, ++ }, ++ { ++ .name = "ledG", /* green led */ ++ .bit = 6, ++ }, ++ { ++ .name = "ledH", /* green led */ ++ .bit = 7, ++ } ++}; ++ ++static struct latch_led_platform_data cambria_latch_leds_data = { ++ .num_leds = 8, ++ .leds = cambria_latch_leds, ++ .mem = 0x53F40000, ++}; ++ ++static struct platform_device cambria_latch_leds_device = { ++ .name = "leds-latch", ++ .id = -1, ++ .dev.platform_data = &cambria_latch_leds_data, ++}; ++ ++static struct resource cambria_usb0_resources[] = { ++ { ++ .start = 0xCD000000, ++ .end = 0xCD000300, ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = 32, ++ .flags = IORESOURCE_IRQ, ++ }, ++}; ++ ++static struct resource cambria_usb1_resources[] = { ++ { ++ .start = 0xCE000000, ++ .end = 0xCE000300, ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = 33, ++ .flags = IORESOURCE_IRQ, ++ }, ++}; ++ ++static u64 ehci_dma_mask = ~(u32)0; ++ ++static struct usb_ehci_pdata cambria_usb_pdata = { ++ .big_endian_desc = 1, ++ .big_endian_mmio = 1, ++ .has_tt = 1, ++ .caps_offset = 0x100, ++}; ++ ++static struct platform_device cambria_usb0_device = { ++ .name = "ehci-platform", ++ .id = 0, ++ .resource = cambria_usb0_resources, ++ .num_resources = ARRAY_SIZE(cambria_usb0_resources), ++ .dev = { ++ .dma_mask = &ehci_dma_mask, ++ .coherent_dma_mask = 0xffffffff, ++ .platform_data = &cambria_usb_pdata, ++ }, ++}; ++ ++static struct platform_device cambria_usb1_device = { ++ .name = "ehci-platform", ++ .id = 1, ++ .resource = cambria_usb1_resources, ++ .num_resources = ARRAY_SIZE(cambria_usb1_resources), ++ .dev = { ++ .dma_mask = &ehci_dma_mask, ++ .coherent_dma_mask = 0xffffffff, ++ .platform_data = &cambria_usb_pdata, ++ }, ++}; ++ ++static struct gw_i2c_pld_platform_data gw_i2c_pld_data0 = { ++ .gpio_base = 16, ++ .nr_gpio = 8, ++}; ++ ++static struct gw_i2c_pld_platform_data gw_i2c_pld_data1 = { ++ .gpio_base = 24, ++ .nr_gpio = 2, ++}; ++ ++ ++static struct gpio_keys_button cambria_gpio_buttons[] = { ++ { ++ .desc = "user", ++ .type = EV_KEY, ++ .code = BTN_0, ++ .debounce_interval = 6, ++ .gpio = 25, ++ } ++}; ++ ++static struct gpio_keys_platform_data cambria_gpio_buttons_data = { ++ .poll_interval = 500, ++ .nbuttons = 1, ++ .buttons = cambria_gpio_buttons, ++}; ++ ++static struct platform_device cambria_gpio_buttons_device = { ++ .name = "gpio-keys-polled", ++ .id = -1, ++ .dev.platform_data = &cambria_gpio_buttons_data, ++}; ++ ++static struct platform_device *cambria_devices[] __initdata = { ++ &cambria_i2c_gpio, ++ &cambria_flash, ++ &cambria_uart, ++}; ++ ++static int cambria_register_gpio(struct gpio *array, size_t num) ++{ ++ int i, err, ret; ++ ++ ret = 0; ++ for (i = 0; i < num; i++, array++) { ++ const char *label = array->label; ++ if (label[0] == '*') ++ label++; ++ err = gpio_request_one(array->gpio, array->flags, label); ++ if (err) ++ ret = err; ++ else { ++ err = gpio_export(array->gpio, array->label[0] != '*'); ++ } ++ } ++ return ret; ++} ++ ++static void __init cambria_gw23xx_setup(void) ++{ ++ cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\ ++ (1 << 5) | (1 << 8) | (1 << 9) | (1 << 12); ++ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start; ++ ++ platform_device_register(&cambria_npec_device); ++ platform_device_register(&cambria_npea_device); ++} ++ ++static void __init cambria_gw2350_setup(void) ++{ ++ *IXP4XX_EXP_CS2 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING); ++ cambria_optional_uart_data[0].mapbase = 0x52FF0000; ++ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x52FF0000, 0x0fff); ++ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3; ++ ++ *IXP4XX_EXP_CS3 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING); ++ cambria_optional_uart_data[1].mapbase = 0x53FF0000; ++ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53FF0000, 0x0fff); ++ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4; ++ ++ cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\ ++ (1 << 5) | (1 << 8) | (1 << 9) | (1 << 12); ++ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start; ++ ++ platform_device_register(&cambria_optional_uart); ++ platform_device_register(&cambria_npec_device); ++ platform_device_register(&cambria_npea_device); ++ ++ platform_device_register(&cambria_usb0_device); ++ platform_device_register(&cambria_usb1_device); ++ ++ platform_device_register(&cambria_gpio_leds_device); ++ ++ /* gpio config (/sys/class/gpio) */ ++ cambria_register_gpio(ARRAY_AND_SIZE(cambria_gpios_gw2350)); ++} ++ ++static void __init cambria_gw2358_setup(void) ++{ ++ *IXP4XX_EXP_CS3 = 0xBFFF3C43; // bit0 = 16bit vs 8bit bus ++ irq_set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING); ++ cambria_optional_uart_data[0].mapbase = 0x53FC0000; ++ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x53FC0000, 0x0fff); ++ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3; ++ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING); ++ cambria_optional_uart_data[1].mapbase = 0x53F80000; ++ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53F80000, 0x0fff); ++ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4; ++ ++ cambria_gpio_resources[0].start = (1 << 14) | (1 << 16) | (1 << 17) | (1 << 18) |\ ++ (1 << 19) | (1 << 20) | (1 << 24) | (1 << 25); ++ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start; ++ ++ platform_device_register(&cambria_optional_uart); ++ ++ platform_device_register(&cambria_npec_device); ++ platform_device_register(&cambria_npea_device); ++ ++ platform_device_register(&cambria_usb0_device); ++ platform_device_register(&cambria_usb1_device); ++ ++ platform_device_register(&cambria_pata); ++ ++ cambria_gpio_leds[0].gpio = 24; ++ platform_device_register(&cambria_gpio_leds_device); ++ ++ platform_device_register(&cambria_latch_leds_device); ++ ++ platform_device_register(&cambria_gpio_buttons_device); ++ ++ /* gpio config (/sys/class/gpio) */ ++ cambria_register_gpio(ARRAY_AND_SIZE(cambria_gpios_gw2358)); ++} ++ ++static void __init cambria_gw2359_setup(void) ++{ ++#if defined(CONFIG_MVSWITCH_PHY) || defined(CONFIG_MVSWITCH_PHY_MODULE) ++ /* The mvswitch driver has some hard-coded values which could ++ * easily be turned into a platform resource if needed. For now they ++ * match our hardware configuration: ++ * MV_BASE 0x10 - phy base address ++ * MV_WANPORT 0 - Port0 (ENET2) is WAN (SFP module) ++ * MV_CPUPORT 5 - Port5 is CPU NPEA (eth1) ++ * ++ * The mvswitch driver registers a fixup which forces a driver match ++ * if phy_addr matches MV_BASE ++ * ++ * Two static defautl VLAN's are created: WAN port in 1, and all other ports ++ * in the other. ++ */ ++ cambria_npea_data.phy = 0x10; // mvswitch driver catches this ++#else ++ // Switch Port5 to CPU is MII<->MII (no PHY) - this disables the genphy driver ++ cambria_npea_data.phy = IXP4XX_ETH_PHY_MAX_ADDR; ++ // CPU NPE-C is in bridge bypass mode to Port4 PHY@0x14 ++ cambria_npec_data.phy = 0x14; ++#endif ++ platform_device_register(&cambria_npec_device); ++ platform_device_register(&cambria_npea_device); ++ ++ platform_device_register(&cambria_usb0_device); ++ platform_device_register(&cambria_usb1_device); ++ ++ cambria_gpio_leds_data.num_leds = 3; ++ cambria_gpio_leds[0].name = "user1"; ++ cambria_gpio_leds[0].gpio = 125; // PNLLED1# ++ cambria_gpio_leds[1].gpio = 126; // PNLLED3# ++ cambria_gpio_leds[2].gpio = 119; // PNLLED4# ++ platform_device_register(&cambria_gpio_leds_device); ++ ++#if (IS_ENABLED(CONFIG_KEYBOARD_GPIO_POLLED)) ++ cambria_gpio_buttons[0].gpio = 100; ++ platform_device_register(&cambria_gpio_buttons_device); ++#endif ++ ++ /* gpio config (/sys/class/gpio) */ ++ cambria_register_gpio(ARRAY_AND_SIZE(cambria_gpios_gw2359)); ++} ++ ++static void __init cambria_gw2360_setup(void) ++{ ++ /* The GW2360 has 8 UARTs in addition to the 1 IXP4xxx UART. ++ * The chip-selects are expanded via a 3-to-8 decoder and CS2 ++ * and they are 8bit devices ++ */ ++ *IXP4XX_EXP_CS2 = 0xBFFF3C43; ++ cambria_optional_uart_data[0].mapbase = 0x52000000; ++ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x52000000, 0x0fff); ++ cambria_optional_uart_data[0].uartclk = 18432000; ++ cambria_optional_uart_data[0].iotype = UPIO_MEM; ++ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO2; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO2, IRQ_TYPE_EDGE_RISING); ++ ++ cambria_optional_uart_data[1].mapbase = 0x52000008; ++ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x52000008, 0x0fff); ++ cambria_optional_uart_data[1].uartclk = 18432000; ++ cambria_optional_uart_data[1].iotype = UPIO_MEM; ++ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO3; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING); ++ ++ cambria_optional_uart_data[2].mapbase = 0x52000010; ++ cambria_optional_uart_data[2].membase = (void __iomem *)ioremap(0x52000010, 0x0fff); ++ cambria_optional_uart_data[2].uartclk = 18432000; ++ cambria_optional_uart_data[2].iotype = UPIO_MEM; ++ cambria_optional_uart_data[2].irq = IRQ_IXP4XX_GPIO4; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING); ++ ++ cambria_optional_uart_data[3].mapbase = 0x52000018; ++ cambria_optional_uart_data[3].membase = (void __iomem *)ioremap(0x52000018, 0x0fff); ++ cambria_optional_uart_data[3].uartclk = 18432000; ++ cambria_optional_uart_data[3].iotype = UPIO_MEM; ++ cambria_optional_uart_data[3].irq = IRQ_IXP4XX_GPIO5; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO5, IRQ_TYPE_EDGE_RISING); ++ ++ cambria_optional_uart_data[4].mapbase = 0x52000020; ++ cambria_optional_uart_data[4].membase = (void __iomem *)ioremap(0x52000020, 0x0fff); ++ cambria_optional_uart_data[4].uartclk = 18432000; ++ cambria_optional_uart_data[4].iotype = UPIO_MEM; ++ cambria_optional_uart_data[4].irq = IRQ_IXP4XX_GPIO8; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_EDGE_RISING); ++ ++ cambria_optional_uart_data[5].mapbase = 0x52000028; ++ cambria_optional_uart_data[5].membase = (void __iomem *)ioremap(0x52000028, 0x0fff); ++ cambria_optional_uart_data[5].uartclk = 18432000; ++ cambria_optional_uart_data[5].iotype = UPIO_MEM; ++ cambria_optional_uart_data[5].irq = IRQ_IXP4XX_GPIO9; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_EDGE_RISING); ++ ++ cambria_optional_uart_data[6].mapbase = 0x52000030; ++ cambria_optional_uart_data[6].membase = (void __iomem *)ioremap(0x52000030, 0x0fff); ++ cambria_optional_uart_data[6].uartclk = 18432000; ++ cambria_optional_uart_data[6].iotype = UPIO_MEM; ++ cambria_optional_uart_data[6].irq = IRQ_IXP4XX_GPIO10; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_EDGE_RISING); ++ ++ cambria_optional_uart.num_resources = 7, ++ platform_device_register(&cambria_optional_uart); ++ ++#if defined(CONFIG_MVSWITCH_PHY) || defined(CONFIG_MVSWITCH_PHY_MODULE) ++ /* The mvswitch driver has some hard-coded values which could ++ * easily be turned into a platform resource if needed. For now they ++ * match our hardware configuration: ++ * MV_BASE 0x10 - phy base address ++ * MV_WANPORT 0 - Port0 (ENET2) is WAN (SFP module) ++ * MV_CPUPORT 5 - Port5 is CPU NPEA (eth1) ++ * ++ * The mvswitch driver registers a fixup which forces a driver match ++ * if phy_addr matches MV_BASE ++ * ++ * Two static defautl VLAN's are created: WAN port in 1, and all other ports ++ * in the other. ++ */ ++ cambria_npea_data.phy = 0x10; // mvswitch driver catches this ++#else ++ // Switch Port5 to CPU is MII<->MII (no PHY) - this disables the generic PHY driver ++ cambria_npea_data.phy = IXP4XX_ETH_PHY_MAX_ADDR; ++#endif ++ ++ // disable genphy autonegotiation on NPE-C PHY (eth1) as its 100BaseFX ++ //cambria_npec_data.noautoneg = 1; // disable autoneg ++ cambria_npec_data.speed_10 = 0; // 100mbps ++ cambria_npec_data.half_duplex = 0; // full-duplex ++ platform_device_register(&cambria_npec_device); ++ platform_device_register(&cambria_npea_device); ++ ++ platform_device_register(&cambria_usb0_device); ++ platform_device_register(&cambria_usb1_device); ++ ++ cambria_gpio_leds_data.num_leds = 3; ++ cambria_gpio_leds[0].name = "user1"; ++ cambria_gpio_leds[0].gpio = 125; ++ cambria_gpio_leds[1].gpio = 126; ++ cambria_gpio_leds[2].gpio = 119; ++ platform_device_register(&cambria_gpio_leds_device); ++ ++#if (IS_ENABLED(CONFIG_KEYBOARD_GPIO_POLLED)) ++ cambria_gpio_buttons[0].gpio = 100; ++ platform_device_register(&cambria_gpio_buttons_device); ++#endif ++ ++#ifdef SFP_SERIALID ++ /* the SFP modules each have an i2c bus for serial ident via GSC GPIO ++ * To use these the i2c-gpio driver must be changed to use the _cansleep ++ * varients of gpio_get_value/gpio_set_value (I don't know why it doesn't ++ * use that anyway as it doesn't operate in an IRQ context). ++ * Additionally the i2c-gpio module must set the gpio to output-high prior ++ * to changing direction to an input to enable internal Pullups ++ */ ++ platform_device_register(&cambria_i2c_gpio_sfpa); ++ platform_device_register(&cambria_i2c_gpio_sfpb); ++#endif ++ ++ /* gpio config (/sys/class/gpio) */ ++ cambria_register_gpio(ARRAY_AND_SIZE(cambria_gpios_gw2360)); ++} ++ ++static struct cambria_board_info cambria_boards[] __initdata = { ++ { ++ .model = "GW2350", ++ .setup = cambria_gw2350_setup, ++ }, { ++ .model = "GW2351", ++ .setup = cambria_gw2350_setup, ++ }, { ++ .model = "GW2358", ++ .setup = cambria_gw2358_setup, ++ }, { ++ .model = "GW2359", ++ .setup = cambria_gw2359_setup, ++ }, { ++ .model = "GW2360", ++ .setup = cambria_gw2360_setup, ++ }, { ++ .model = "GW2371", ++ .setup = cambria_gw2358_setup, ++ } ++}; ++ ++static struct cambria_board_info * __init cambria_find_board_info(char *model) ++{ ++ int i; ++ model[6] = '\0'; ++ ++ for (i = 0; i < ARRAY_SIZE(cambria_boards); i++) { ++ struct cambria_board_info *info = &cambria_boards[i]; ++ if (strcmp(info->model, model) == 0) ++ return info; ++ } ++ ++ return NULL; ++} ++ ++static struct memory_accessor *at24_mem_acc; ++ ++static void at24_setup(struct memory_accessor *mem_acc, void *context) ++{ ++ char mac_addr[ETH_ALEN]; ++ char model[7]; ++ ++ at24_mem_acc = mem_acc; ++ ++ /* Read MAC addresses */ ++ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x0, 6) == 6) { ++ memcpy(&cambria_npec_data.hwaddr, mac_addr, ETH_ALEN); ++ } ++ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x6, 6) == 6) { ++ memcpy(&cambria_npea_data.hwaddr, mac_addr, ETH_ALEN); ++ } ++ ++ /* Read the first 6 bytes of the model number */ ++ if (at24_mem_acc->read(at24_mem_acc, model, 0x20, 6) == 6) { ++ cambria_info = cambria_find_board_info(model); ++ } ++ ++} ++ ++static struct at24_platform_data cambria_eeprom_info = { ++ .byte_len = 1024, ++ .page_size = 16, ++ .flags = AT24_FLAG_READONLY, ++ .setup = at24_setup, ++}; ++ ++static struct pca953x_platform_data cambria_pca_data = { ++ .gpio_base = 100, ++ .irq_base = -1, ++}; ++ ++static struct pca953x_platform_data cambria_pca2_data = { ++ .gpio_base = 116, ++ .irq_base = -1, ++}; ++ ++static struct i2c_board_info __initdata cambria_i2c_board_info[] = { ++ { ++ I2C_BOARD_INFO("pca9555", 0x23), ++ .platform_data = &cambria_pca_data, ++ }, ++ { ++ I2C_BOARD_INFO("pca9555", 0x27), ++ .platform_data = &cambria_pca2_data, ++ }, ++ { ++ I2C_BOARD_INFO("ds1672", 0x68), ++ }, ++ { ++ I2C_BOARD_INFO("gsp", 0x29), ++ }, ++ { ++ I2C_BOARD_INFO("ad7418", 0x28), ++ }, ++ { ++ I2C_BOARD_INFO("24c08", 0x51), ++ .platform_data = &cambria_eeprom_info ++ }, ++ { ++ I2C_BOARD_INFO("gw_i2c_pld", 0x56), ++ .platform_data = &gw_i2c_pld_data0, ++ }, ++ { ++ I2C_BOARD_INFO("gw_i2c_pld", 0x57), ++ .platform_data = &gw_i2c_pld_data1, ++ }, ++}; ++ ++static void __init cambria_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ cambria_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ cambria_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; // make sure window is writable ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(ARRAY_AND_SIZE(cambria_devices)); ++ ++ cambria_pata_resources[0].start = 0x53e00000; ++ cambria_pata_resources[0].end = 0x53e3ffff; ++ ++ cambria_pata_resources[1].start = 0x53e40000; ++ cambria_pata_resources[1].end = 0x53e7ffff; ++ ++ cambria_pata_data.cs0_cfg = IXP4XX_EXP_CS3; ++ cambria_pata_data.cs1_cfg = IXP4XX_EXP_CS3; ++ ++ i2c_register_board_info(0, ARRAY_AND_SIZE(cambria_i2c_board_info)); ++} ++ ++static int __init cambria_model_setup(void) ++{ ++ if (!machine_is_cambria()) ++ return 0; ++ ++ if (cambria_info) { ++ printk(KERN_DEBUG "Running on Gateworks Cambria %s\n", ++ cambria_info->model); ++ cambria_info->setup(); ++ } else { ++ printk(KERN_INFO "Unknown/missing Cambria model number" ++ " -- defaults will be used\n"); ++ cambria_gw23xx_setup(); ++ } ++ ++ return 0; ++} ++late_initcall(cambria_model_setup); ++ ++MACHINE_START(CAMBRIA, "Gateworks Cambria series") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = cambria_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END diff --git a/target/linux/ixp4xx/patches-3.14/201-npe_driver_print_license_location.patch b/target/linux/ixp4xx/patches-3.14/201-npe_driver_print_license_location.patch new file mode 100644 index 0000000..f46b9c6 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/201-npe_driver_print_license_location.patch @@ -0,0 +1,11 @@ +--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c ++++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c +@@ -586,6 +586,8 @@ int npe_load_firmware(struct npe *npe, c + npe_reset(npe); + #endif + ++ print_npe(KERN_INFO, npe, "firmware's license can be found in /usr/share/doc/LICENSE.IPL\n"); ++ + print_npe(KERN_INFO, npe, "firmware functionality 0x%X, " + "revision 0x%X:%X\n", (image->id >> 16) & 0xFF, + (image->id >> 8) & 0xFF, image->id & 0xFF); diff --git a/target/linux/ixp4xx/patches-3.14/203-npe_driver_mask_phy_features.patch b/target/linux/ixp4xx/patches-3.14/203-npe_driver_mask_phy_features.patch new file mode 100644 index 0000000..7d35781 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/203-npe_driver_mask_phy_features.patch @@ -0,0 +1,13 @@ +--- a/drivers/net/ethernet/xscale/ixp4xx_eth.c ++++ b/drivers/net/ethernet/xscale/ixp4xx_eth.c +@@ -1483,6 +1483,10 @@ static int eth_init_one(struct platform_ + goto err_free_mem; + } + ++ /* mask with MAC supported features */ ++ port->phydev->supported &= PHY_BASIC_FEATURES; ++ port->phydev->advertising = port->phydev->supported; ++ + port->phydev->irq = PHY_POLL; + + if ((err = register_netdev(dev))) diff --git a/target/linux/ixp4xx/patches-3.14/205-npe_driver_separate_phy_functions.patch b/target/linux/ixp4xx/patches-3.14/205-npe_driver_separate_phy_functions.patch new file mode 100644 index 0000000..fa577e2 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/205-npe_driver_separate_phy_functions.patch @@ -0,0 +1,131 @@ +From e3eab80fb5d0a7d7fdb0f2f231b27161d5ec3804 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 30 Jun 2013 15:52:53 +0200 +Subject: [PATCH 23/36] 205-npe_driver_separate_phy_functions.patch + +--- + drivers/net/ethernet/xscale/ixp4xx_eth.c | 70 ++++++++++++++++++++++-------- + 1 file changed, 51 insertions(+), 19 deletions(-) + +--- a/drivers/net/ethernet/xscale/ixp4xx_eth.c ++++ b/drivers/net/ethernet/xscale/ixp4xx_eth.c +@@ -593,6 +593,51 @@ static void ixp4xx_adjust_link(struct ne + dev->name, port->speed, port->duplex ? "full" : "half"); + } + ++static int ixp4xx_phy_connect(struct net_device *dev) ++{ ++ struct port *port = netdev_priv(dev); ++ struct eth_plat_info *plat = port->plat; ++ char phy_id[MII_BUS_ID_SIZE + 3]; ++ ++ snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, ++ mdio_bus->id, plat->phy); ++ port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, ++ PHY_INTERFACE_MODE_MII); ++ if (IS_ERR(port->phydev)) { ++ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); ++ return PTR_ERR(port->phydev); ++ } ++ ++ /* mask with MAC supported features */ ++ port->phydev->supported &= PHY_BASIC_FEATURES; ++ port->phydev->advertising = port->phydev->supported; ++ ++ port->phydev->irq = PHY_POLL; ++ ++ return 0; ++} ++ ++static void ixp4xx_phy_disconnect(struct net_device *dev) ++{ ++ struct port *port = netdev_priv(dev); ++ ++ phy_disconnect(port->phydev); ++} ++ ++static void ixp4xx_phy_start(struct net_device *dev) ++{ ++ struct port *port = netdev_priv(dev); ++ ++ port->speed = 0; /* force "link up" message */ ++ phy_start(port->phydev); ++} ++ ++static void ixp4xx_phy_stop(struct net_device *dev) ++{ ++ struct port *port = netdev_priv(dev); ++ ++ phy_stop(port->phydev); ++} + + static inline void debug_pkt(struct net_device *dev, const char *func, + u8 *data, int len) +@@ -1263,8 +1308,7 @@ static int eth_open(struct net_device *d + return err; + } + +- port->speed = 0; /* force "link up" message */ +- phy_start(port->phydev); ++ ixp4xx_phy_start(dev); + + for (i = 0; i < ETH_ALEN; i++) + __raw_writel(dev->dev_addr[i], &port->regs->hw_addr[i]); +@@ -1385,7 +1429,7 @@ static int eth_close(struct net_device * + printk(KERN_CRIT "%s: unable to disable loopback\n", + dev->name); + +- phy_stop(port->phydev); ++ ixp4xx_phy_stop(dev); + + if (!ports_open) + qmgr_disable_irq(TXDONE_QUEUE); +@@ -1411,7 +1455,6 @@ static int eth_init_one(struct platform_ + struct net_device *dev; + struct eth_plat_info *plat = dev_get_platdata(&pdev->dev); + u32 regs_phys; +- char phy_id[MII_BUS_ID_SIZE + 3]; + int err; + + if (ptp_filter_init(ptp_filter, ARRAY_SIZE(ptp_filter))) { +@@ -1474,20 +1517,9 @@ static int eth_init_one(struct platform_ + __raw_writel(DEFAULT_CORE_CNTRL, &port->regs->core_control); + udelay(50); + +- snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, +- mdio_bus->id, plat->phy); +- port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, +- PHY_INTERFACE_MODE_MII); +- if (IS_ERR(port->phydev)) { +- err = PTR_ERR(port->phydev); ++ err = ixp4xx_phy_connect(dev); ++ if (err) + goto err_free_mem; +- } +- +- /* mask with MAC supported features */ +- port->phydev->supported &= PHY_BASIC_FEATURES; +- port->phydev->advertising = port->phydev->supported; +- +- port->phydev->irq = PHY_POLL; + + if ((err = register_netdev(dev))) + goto err_phy_dis; +@@ -1498,7 +1530,7 @@ static int eth_init_one(struct platform_ + return 0; + + err_phy_dis: +- phy_disconnect(port->phydev); ++ ixp4xx_phy_disconnect(dev); + err_free_mem: + npe_port_tab[NPE_ID(port->id)] = NULL; + release_resource(port->mem_res); +@@ -1515,7 +1547,7 @@ static int eth_remove_one(struct platfor + struct port *port = netdev_priv(dev); + + unregister_netdev(dev); +- phy_disconnect(port->phydev); ++ ixp4xx_phy_disconnect(dev); + npe_port_tab[NPE_ID(port->id)] = NULL; + npe_release(port->npe); + release_resource(port->mem_res); diff --git a/target/linux/ixp4xx/patches-3.14/206-npe_driver_add_update_link_function.patch b/target/linux/ixp4xx/patches-3.14/206-npe_driver_add_update_link_function.patch new file mode 100644 index 0000000..cb06069 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/206-npe_driver_add_update_link_function.patch @@ -0,0 +1,98 @@ +--- a/drivers/net/ethernet/xscale/ixp4xx_eth.c ++++ b/drivers/net/ethernet/xscale/ixp4xx_eth.c +@@ -177,7 +177,7 @@ struct port { + struct desc *desc_tab; /* coherent */ + u32 desc_tab_phys; + int id; /* logical port ID */ +- int speed, duplex; ++ int link, speed, duplex; + u8 firmware[4]; + int hwts_tx_en; + int hwts_rx_en; +@@ -562,37 +562,52 @@ static void ixp4xx_mdio_remove(void) + mdiobus_free(mdio_bus); + } + +- +-static void ixp4xx_adjust_link(struct net_device *dev) ++static void ixp4xx_update_link(struct net_device *dev) + { + struct port *port = netdev_priv(dev); +- struct phy_device *phydev = port->phydev; + +- if (!phydev->link) { +- if (port->speed) { +- port->speed = 0; +- printk(KERN_INFO "%s: link down\n", dev->name); +- } ++ if (!port->link) { ++ netif_carrier_off(dev); ++ printk(KERN_INFO "%s: link down\n", dev->name); + return; + } + +- if (port->speed == phydev->speed && port->duplex == phydev->duplex) +- return; +- +- port->speed = phydev->speed; +- port->duplex = phydev->duplex; +- +- if (port->duplex) ++ if (port->duplex == DUPLEX_FULL) + __raw_writel(DEFAULT_TX_CNTRL0 & ~TX_CNTRL0_HALFDUPLEX, + &port->regs->tx_control[0]); + else + __raw_writel(DEFAULT_TX_CNTRL0 | TX_CNTRL0_HALFDUPLEX, + &port->regs->tx_control[0]); + ++ netif_carrier_on(dev); + printk(KERN_INFO "%s: link up, speed %u Mb/s, %s duplex\n", + dev->name, port->speed, port->duplex ? "full" : "half"); + } + ++static void ixp4xx_adjust_link(struct net_device *dev) ++{ ++ struct port *port = netdev_priv(dev); ++ struct phy_device *phydev = port->phydev; ++ int status_change = 0; ++ ++ if (phydev->link) { ++ if (port->duplex != phydev->duplex ++ || port->speed != phydev->speed) { ++ status_change = 1; ++ } ++ } ++ ++ if (phydev->link != port->link) ++ status_change = 1; ++ ++ port->link = phydev->link; ++ port->speed = phydev->speed; ++ port->duplex = phydev->duplex; ++ ++ if (status_change) ++ ixp4xx_update_link(dev); ++} ++ + static int ixp4xx_phy_connect(struct net_device *dev) + { + struct port *port = netdev_priv(dev); +@@ -628,7 +643,6 @@ static void ixp4xx_phy_start(struct net_ + { + struct port *port = netdev_priv(dev); + +- port->speed = 0; /* force "link up" message */ + phy_start(port->phydev); + } + +@@ -1524,6 +1538,10 @@ static int eth_init_one(struct platform_ + if ((err = register_netdev(dev))) + goto err_phy_dis; + ++ port->link = 0; ++ port->speed = 0; ++ port->duplex = -1; ++ + printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, plat->phy, + npe_name(port->npe)); + diff --git a/target/linux/ixp4xx/patches-3.14/207-npe_driver_multiphy_support.patch b/target/linux/ixp4xx/patches-3.14/207-npe_driver_multiphy_support.patch new file mode 100644 index 0000000..c1dda69 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/207-npe_driver_multiphy_support.patch @@ -0,0 +1,154 @@ +TODO: take care of additional PHYs through the PHY abstraction layer + +--- a/arch/arm/mach-ixp4xx/include/mach/platform.h ++++ b/arch/arm/mach-ixp4xx/include/mach/platform.h +@@ -74,7 +74,7 @@ extern unsigned long ixp4xx_exp_bus_size + /* + * Clock Speed Definitions. + */ +-#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66Mhzi APB BUS */ ++#define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66Mhzi APB BUS */ + #define IXP4XX_UART_XTAL 14745600 + + /* +@@ -95,12 +95,23 @@ struct ixp4xx_pata_data { + #define IXP4XX_ETH_NPEB 0x10 + #define IXP4XX_ETH_NPEC 0x20 + ++#define IXP4XX_ETH_PHY_MAX_ADDR 32 ++ + /* Information about built-in Ethernet MAC interfaces */ + struct eth_plat_info { + u8 phy; /* MII PHY ID, 0 - 31 */ + u8 rxq; /* configurable, currently 0 - 31 only */ + u8 txreadyq; + u8 hwaddr[6]; ++ ++ u32 phy_mask; ++#if 0 ++ int speed; ++ int duplex; ++#else ++ int speed_10; ++ int half_duplex; ++#endif + }; + + /* Information about built-in HSS (synchronous serial) interfaces */ +--- a/drivers/net/ethernet/xscale/ixp4xx_eth.c ++++ b/drivers/net/ethernet/xscale/ixp4xx_eth.c +@@ -614,6 +614,37 @@ static int ixp4xx_phy_connect(struct net + struct eth_plat_info *plat = port->plat; + char phy_id[MII_BUS_ID_SIZE + 3]; + ++ if (plat->phy == IXP4XX_ETH_PHY_MAX_ADDR) { ++#if 0 ++ switch (plat->speed) { ++ case SPEED_10: ++ case SPEED_100: ++ break; ++ default: ++ printk(KERN_ERR "%s: invalid speed (%d)\n", ++ dev->name, plat->speed); ++ return -EINVAL; ++ } ++ ++ switch (plat->duplex) { ++ case DUPLEX_HALF: ++ case DUPLEX_FULL: ++ break; ++ default: ++ printk(KERN_ERR "%s: invalid duplex mode (%d)\n", ++ dev->name, plat->duplex); ++ return -EINVAL; ++ } ++ port->speed = plat->speed; ++ port->duplex = plat->duplex; ++#else ++ port->speed = plat->speed_10 ? SPEED_10 : SPEED_100; ++ port->duplex = plat->half_duplex ? DUPLEX_HALF : DUPLEX_FULL; ++#endif ++ ++ return 0; ++ } ++ + snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, + mdio_bus->id, plat->phy); + port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, +@@ -636,21 +667,32 @@ static void ixp4xx_phy_disconnect(struct + { + struct port *port = netdev_priv(dev); + +- phy_disconnect(port->phydev); ++ if (port->phydev) ++ phy_disconnect(port->phydev); + } + + static void ixp4xx_phy_start(struct net_device *dev) + { + struct port *port = netdev_priv(dev); + +- phy_start(port->phydev); ++ if (port->phydev) { ++ phy_start(port->phydev); ++ } else { ++ port->link = 1; ++ ixp4xx_update_link(dev); ++ } + } + + static void ixp4xx_phy_stop(struct net_device *dev) + { + struct port *port = netdev_priv(dev); + +- phy_stop(port->phydev); ++ if (port->phydev) { ++ phy_stop(port->phydev); ++ } else { ++ port->link = 0; ++ ixp4xx_update_link(dev); ++ } + } + + static inline void debug_pkt(struct net_device *dev, const char *func, +@@ -1052,6 +1094,9 @@ static int eth_ioctl(struct net_device * + return hwtstamp_get(dev, req); + } + ++ if (!port->phydev) ++ return -EOPNOTSUPP; ++ + return phy_mii_ioctl(port->phydev, req, cmd); + } + +@@ -1072,18 +1117,30 @@ static void ixp4xx_get_drvinfo(struct ne + static int ixp4xx_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) + { + struct port *port = netdev_priv(dev); ++ ++ if (!port->phydev) ++ return -EOPNOTSUPP; ++ + return phy_ethtool_gset(port->phydev, cmd); + } + + static int ixp4xx_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) + { + struct port *port = netdev_priv(dev); ++ ++ if (!port->phydev) ++ return -EOPNOTSUPP; ++ + return phy_ethtool_sset(port->phydev, cmd); + } + + static int ixp4xx_nway_reset(struct net_device *dev) + { + struct port *port = netdev_priv(dev); ++ ++ if (!port->phydev) ++ return -EOPNOTSUPP; ++ + return phy_start_aneg(port->phydev); + } + diff --git a/target/linux/ixp4xx/patches-3.14/295-latch_led_driver.patch b/target/linux/ixp4xx/patches-3.14/295-latch_led_driver.patch new file mode 100644 index 0000000..0d5119d --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/295-latch_led_driver.patch @@ -0,0 +1,201 @@ +--- a/drivers/leds/Kconfig ++++ b/drivers/leds/Kconfig +@@ -251,6 +251,12 @@ config LEDS_LP8788 + help + This option enables support for the Keyboard LEDs on the LP8788 PMIC. + ++config LEDS_LATCH ++ tristate "LED Support for Memory Latched LEDs" ++ depends on LEDS_CLASS ++ help ++ -- To Do -- ++ + config LEDS_CLEVO_MAIL + tristate "Mail LED on Clevo notebook" + depends on LEDS_CLASS +--- a/drivers/leds/Makefile ++++ b/drivers/leds/Makefile +@@ -22,6 +22,7 @@ obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunf + obj-$(CONFIG_LEDS_PCA9532) += leds-pca9532.o + obj-$(CONFIG_LEDS_GPIO_REGISTER) += leds-gpio-register.o + obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o ++obj-$(CONFIG_LEDS_LATCH) += leds-latch.o + obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o + obj-$(CONFIG_LEDS_LP55XX_COMMON) += leds-lp55xx-common.o + obj-$(CONFIG_LEDS_LP5521) += leds-lp5521.o +--- /dev/null ++++ b/drivers/leds/leds-latch.c +@@ -0,0 +1,152 @@ ++/* ++ * LEDs driver for Memory Latched Devices ++ * ++ * Copyright (C) 2008 Gateworks Corp. ++ * Chris Lang <clang@gateworks.com> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++#include <linux/kernel.h> ++#include <linux/slab.h> ++#include <linux/init.h> ++#include <linux/platform_device.h> ++#include <linux/leds.h> ++#include <linux/workqueue.h> ++#include <asm/io.h> ++#include <linux/spinlock.h> ++#include <linux/slab.h> ++#include <linux/module.h> ++#include <linux/export.h> ++ ++static unsigned int mem_keep = 0xFF; ++static spinlock_t mem_lock; ++static unsigned char *iobase; ++ ++struct latch_led_data { ++ struct led_classdev cdev; ++ struct work_struct work; ++ u8 new_level; ++ u8 bit; ++ void (*set_led)(u8 bit, enum led_brightness value); ++}; ++ ++static void latch_set_led(u8 bit, enum led_brightness value) ++{ ++ if (value == LED_OFF) ++ mem_keep |= (0x1 << bit); ++ else ++ mem_keep &= ~(0x1 << bit); ++ ++ writeb(mem_keep, iobase); ++} ++ ++static void latch_led_set(struct led_classdev *led_cdev, ++ enum led_brightness value) ++{ ++ struct latch_led_data *led_dat = ++ container_of(led_cdev, struct latch_led_data, cdev); ++ ++ raw_spin_lock(mem_lock); ++ ++ led_dat->set_led(led_dat->bit, value); ++ ++ raw_spin_unlock(mem_lock); ++} ++ ++static int latch_led_probe(struct platform_device *pdev) ++{ ++ struct latch_led_platform_data *pdata = pdev->dev.platform_data; ++ struct latch_led *cur_led; ++ struct latch_led_data *leds_data, *led_dat; ++ int i, ret = 0; ++ ++ if (!pdata) ++ return -EBUSY; ++ ++ leds_data = kzalloc(sizeof(struct latch_led_data) * pdata->num_leds, ++ GFP_KERNEL); ++ if (!leds_data) ++ return -ENOMEM; ++ ++ for (i = 0; i < pdata->num_leds; i++) { ++ cur_led = &pdata->leds[i]; ++ led_dat = &leds_data[i]; ++ ++ led_dat->cdev.name = cur_led->name; ++ led_dat->cdev.default_trigger = cur_led->default_trigger; ++ led_dat->cdev.brightness_set = latch_led_set; ++ led_dat->cdev.brightness = LED_OFF; ++ led_dat->bit = cur_led->bit; ++ led_dat->set_led = pdata->set_led ? pdata->set_led : latch_set_led; ++ ++ ret = led_classdev_register(&pdev->dev, &led_dat->cdev); ++ if (ret < 0) { ++ goto err; ++ } ++ } ++ ++ if (!pdata->set_led) { ++ iobase = ioremap_nocache(pdata->mem, 0x1000); ++ writeb(0xFF, iobase); ++ } ++ platform_set_drvdata(pdev, leds_data); ++ ++ return 0; ++ ++err: ++ if (i > 0) { ++ for (i = i - 1; i >= 0; i--) { ++ led_classdev_unregister(&leds_data[i].cdev); ++ } ++ } ++ ++ kfree(leds_data); ++ ++ return ret; ++} ++ ++static int latch_led_remove(struct platform_device *pdev) ++{ ++ int i; ++ struct latch_led_platform_data *pdata = pdev->dev.platform_data; ++ struct latch_led_data *leds_data; ++ ++ leds_data = platform_get_drvdata(pdev); ++ ++ for (i = 0; i < pdata->num_leds; i++) { ++ led_classdev_unregister(&leds_data[i].cdev); ++ cancel_work_sync(&leds_data[i].work); ++ } ++ ++ kfree(leds_data); ++ ++ return 0; ++} ++ ++static struct platform_driver latch_led_driver = { ++ .probe = latch_led_probe, ++ .remove = latch_led_remove, ++ .driver = { ++ .name = "leds-latch", ++ .owner = THIS_MODULE, ++ }, ++}; ++ ++static int __init latch_led_init(void) ++{ ++ return platform_driver_register(&latch_led_driver); ++} ++ ++static void __exit latch_led_exit(void) ++{ ++ platform_driver_unregister(&latch_led_driver); ++} ++ ++module_init(latch_led_init); ++module_exit(latch_led_exit); ++ ++MODULE_AUTHOR("Chris Lang <clang@gateworks.com>"); ++MODULE_DESCRIPTION("Latch LED driver"); +--- a/include/linux/leds.h ++++ b/include/linux/leds.h +@@ -285,4 +285,18 @@ static inline void ledtrig_cpu(enum cpu_ + } + #endif + ++/* For the leds-latch driver */ ++struct latch_led { ++ const char *name; ++ char *default_trigger; ++ unsigned bit; ++}; ++ ++struct latch_led_platform_data { ++ int num_leds; ++ u32 mem; ++ struct latch_led *leds; ++ void (*set_led)(u8 bit, enum led_brightness value); ++}; ++ + #endif /* __LINUX_LEDS_H_INCLUDED */ diff --git a/target/linux/ixp4xx/patches-3.14/300-avila_support.patch b/target/linux/ixp4xx/patches-3.14/300-avila_support.patch new file mode 100644 index 0000000..2e39328 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/300-avila_support.patch @@ -0,0 +1,730 @@ +Index: linux-3.14.25/arch/arm/mach-ixp4xx/avila-pci.c +=================================================================== +--- linux-3.14.25.orig/arch/arm/mach-ixp4xx/avila-pci.c 2014-11-30 15:25:58.890640602 +0100 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/avila-pci.c 2014-11-30 15:26:43.548148782 +0100 +@@ -27,8 +27,8 @@ + #include <mach/hardware.h> + #include <asm/mach-types.h> + +-#define AVILA_MAX_DEV 4 +-#define LOFT_MAX_DEV 6 ++#define AVILA_MAX_DEV 6 ++ + #define IRQ_LINES 4 + + /* PCI controller GPIO to IRQ pin mappings */ +@@ -55,10 +55,8 @@ + IXP4XX_GPIO_IRQ(INTD) + }; + +- if (slot >= 1 && +- slot <= (machine_is_loft() ? LOFT_MAX_DEV : AVILA_MAX_DEV) && +- pin >= 1 && pin <= IRQ_LINES) +- return pci_irq_table[(slot + pin - 2) % 4]; ++ if (slot >= 1 && slot <= AVILA_MAX_DEV && pin >= 1 && pin <= IRQ_LINES) ++ return pci_irq_table[(slot + pin - 2) % IRQ_LINES]; + + return -1; + } +Index: linux-3.14.25/arch/arm/mach-ixp4xx/avila-setup.c +=================================================================== +--- linux-3.14.25.orig/arch/arm/mach-ixp4xx/avila-setup.c 2014-11-30 15:25:58.890640602 +0100 ++++ linux-3.14.25/arch/arm/mach-ixp4xx/avila-setup.c 2014-11-30 16:03:14.803148025 +0100 +@@ -14,9 +14,16 @@ + #include <linux/kernel.h> + #include <linux/init.h> + #include <linux/device.h> ++#include <linux/if_ether.h> ++#include <linux/socket.h> ++#include <linux/netdevice.h> + #include <linux/serial.h> + #include <linux/tty.h> + #include <linux/serial_8250.h> ++#include <linux/i2c.h> ++#include <linux/platform_data/at24.h> ++#include <linux/leds.h> ++#include <linux/platform_data/pca953x.h> + #include <linux/i2c-gpio.h> + #include <asm/types.h> + #include <asm/setup.h> +@@ -26,10 +33,25 @@ + #include <asm/irq.h> + #include <asm/mach/arch.h> + #include <asm/mach/flash.h> ++#include <linux/irq.h> + + #define AVILA_SDA_PIN 7 + #define AVILA_SCL_PIN 6 + ++/* User LEDs */ ++#define AVILA_GW23XX_LED_USER_GPIO 3 ++#define AVILA_GW23X7_LED_USER_GPIO 4 ++ ++/* gpio mask used by platform device */ ++#define AVILA_GPIO_MASK (1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) | (1 << 9) ++ ++struct avila_board_info { ++ unsigned char *model; ++ void (*setup)(void); ++}; ++ ++static struct avila_board_info *avila_info __initdata; ++ + static struct flash_platform_data avila_flash_data = { + .map_name = "cfi_probe", + .width = 2, +@@ -105,14 +127,69 @@ + .resource = avila_uart_resources + }; + +-static struct resource avila_pata_resources[] = { ++static struct resource avila_optional_uart_resources[] = { + { +- .flags = IORESOURCE_MEM +- }, ++ .start = 0x54000000, ++ .end = 0x54000fff, ++ .flags = IORESOURCE_MEM ++ },{ ++ .start = 0x55000000, ++ .end = 0x55000fff, ++ .flags = IORESOURCE_MEM ++ },{ ++ .start = 0x56000000, ++ .end = 0x56000fff, ++ .flags = IORESOURCE_MEM ++ },{ ++ .start = 0x57000000, ++ .end = 0x57000fff, ++ .flags = IORESOURCE_MEM ++ } ++}; ++ ++static struct plat_serial8250_port avila_optional_uart_data[] = { + { +- .flags = IORESOURCE_MEM, ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ .rw_delay = 2, ++ },{ ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ .rw_delay = 2, ++ },{ ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ .rw_delay = 2, ++ },{ ++ .flags = UPF_BOOT_AUTOCONF, ++ .iotype = UPIO_MEM, ++ .regshift = 0, ++ .uartclk = 18432000, ++ .rw_delay = 2, + }, ++ { } ++}; ++ ++static struct platform_device avila_optional_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM1, ++ .dev.platform_data = avila_optional_uart_data, ++ .num_resources = 4, ++ .resource = avila_optional_uart_resources, ++}; ++ ++static struct resource avila_pata_resources[] = { + { ++ .flags = IORESOURCE_MEM ++ },{ ++ .flags = IORESOURCE_MEM, ++ },{ + .name = "intrq", + .start = IRQ_IXP4XX_GPIO12, + .end = IRQ_IXP4XX_GPIO12, +@@ -133,21 +210,237 @@ + .resource = avila_pata_resources, + }; + ++/* Built-in 10/100 Ethernet MAC interfaces */ ++static struct eth_plat_info avila_npeb_data = { ++ .phy = 0, ++ .rxq = 3, ++ .txreadyq = 20, ++}; ++ ++static struct eth_plat_info avila_npec_data = { ++ .phy = 1, ++ .rxq = 4, ++ .txreadyq = 21, ++}; ++ ++static struct platform_device avila_npeb_device = { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = &avila_npeb_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++}; ++ ++static struct platform_device avila_npec_device = { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = &avila_npec_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++}; ++ ++static struct gpio_led avila_gpio_leds[] = { ++ { ++ .name = "user", /* green led */ ++ .gpio = AVILA_GW23XX_LED_USER_GPIO, ++ .active_low = 1, ++ }, ++ { ++ .name = "radio1", /* green led */ ++ .gpio = 104, ++ .active_low = 1, ++ }, ++ { ++ .name = "radio2", /* green led */ ++ .gpio = 105, ++ .active_low = 1, ++ }, ++ { ++ .name = "radio3", /* green led */ ++ .gpio = 106, ++ .active_low = 1, ++ }, ++ { ++ .name = "radio4", /* green led */ ++ .gpio = 107, ++ .active_low = 1, ++ }, ++ ++}; ++ ++static struct gpio_led_platform_data avila_gpio_leds_data = { ++ .num_leds = 1, ++ .leds = avila_gpio_leds, ++}; ++ ++static struct platform_device avila_gpio_leds_device = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev.platform_data = &avila_gpio_leds_data, ++}; ++ ++static struct latch_led avila_latch_leds[] = { ++ { ++ .name = "led0", /* green led */ ++ .bit = 0, ++ }, ++ { ++ .name = "led1", /* green led */ ++ .bit = 1, ++ }, ++ { ++ .name = "led2", /* green led */ ++ .bit = 2, ++ }, ++ { ++ .name = "led3", /* green led */ ++ .bit = 3, ++ }, ++ { ++ .name = "led4", /* green led */ ++ .bit = 4, ++ }, ++ { ++ .name = "led5", /* green led */ ++ .bit = 5, ++ }, ++ { ++ .name = "led6", /* green led */ ++ .bit = 6, ++ }, ++ { ++ .name = "led7", /* green led */ ++ .bit = 7, ++ } ++}; ++ ++static struct latch_led_platform_data avila_latch_leds_data = { ++ .num_leds = 8, ++ .leds = avila_latch_leds, ++ .mem = 0x51000000, ++}; ++ ++static struct platform_device avila_latch_leds_device = { ++ .name = "leds-latch", ++ .id = -1, ++ .dev.platform_data = &avila_latch_leds_data, ++}; ++ + static struct platform_device *avila_devices[] __initdata = { + &avila_i2c_gpio, +- &avila_flash, + &avila_uart + }; + +-static void __init avila_init(void) ++/* ++ * Audio Devices ++ */ ++ ++static struct platform_device avila_hss_device[] = { ++ { ++ .name = "gw_avila_hss", ++ .id = 0, ++ },{ ++ .name = "gw_avila_hss", ++ .id = 1, ++ },{ ++ .name = "gw_avila_hss", ++ .id = 2, ++ },{ ++ .name = "gw_avila_hss", ++ .id = 3, ++ }, ++}; ++ ++static struct platform_device avila_pcm_device[] = { ++ { ++ .name = "gw_avila-audio", ++ .id = 0, ++ },{ ++ .name = "gw_avila-audio", ++ .id = 1, ++ },{ ++ .name = "gw_avila-audio", ++ .id = 2, ++ },{ ++ .name = "gw_avila-audio", ++ .id = 3, ++ } ++}; ++ ++static void setup_audio_devices(void) { ++ platform_device_register(&avila_hss_device[0]); ++ platform_device_register(&avila_hss_device[1]); ++ platform_device_register(&avila_hss_device[2]); ++ platform_device_register(&avila_hss_device[3]); ++ ++ platform_device_register(&avila_pcm_device[0]); ++ platform_device_register(&avila_pcm_device[1]); ++ platform_device_register(&avila_pcm_device[2]); ++ platform_device_register(&avila_pcm_device[3]); ++} ++ ++static void __init avila_gw23xx_setup(void) + { +- ixp4xx_sys_init(); ++ platform_device_register(&avila_npeb_device); ++ platform_device_register(&avila_npec_device); + +- avila_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); +- avila_flash_resource.end = +- IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; ++ platform_device_register(&avila_gpio_leds_device); ++} + +- platform_add_devices(avila_devices, ARRAY_SIZE(avila_devices)); ++static void __init avila_gw2342_setup(void) ++{ ++ platform_device_register(&avila_npeb_device); ++ platform_device_register(&avila_npec_device); ++ ++ platform_device_register(&avila_gpio_leds_device); ++ ++ avila_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1); ++ avila_pata_resources[0].end = IXP4XX_EXP_BUS_END(1); ++ ++ avila_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(2); ++ avila_pata_resources[1].end = IXP4XX_EXP_BUS_END(2); ++ ++ avila_pata_data.cs0_cfg = IXP4XX_EXP_CS1; ++ avila_pata_data.cs1_cfg = IXP4XX_EXP_CS2; ++ ++ platform_device_register(&avila_pata); ++} ++ ++static void __init avila_gw2345_setup(void) ++{ ++ avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR; ++ avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */ ++ platform_device_register(&avila_npeb_device); ++ ++ avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */ ++ platform_device_register(&avila_npec_device); ++ ++ platform_device_register(&avila_gpio_leds_device); ++ ++ avila_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1); ++ avila_pata_resources[0].end = IXP4XX_EXP_BUS_END(1); ++ ++ avila_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(2); ++ avila_pata_resources[1].end = IXP4XX_EXP_BUS_END(2); ++ ++ avila_pata_data.cs0_cfg = IXP4XX_EXP_CS1; ++ avila_pata_data.cs1_cfg = IXP4XX_EXP_CS2; ++ ++ platform_device_register(&avila_pata); ++} ++ ++static void __init avila_gw2347_setup(void) ++{ ++ platform_device_register(&avila_npeb_device); ++ ++ avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO; ++ platform_device_register(&avila_gpio_leds_device); ++} ++ ++static void __init avila_gw2348_setup(void) ++{ ++ platform_device_register(&avila_npeb_device); ++ platform_device_register(&avila_npec_device); ++ ++ platform_device_register(&avila_gpio_leds_device); + + avila_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1); + avila_pata_resources[0].end = IXP4XX_EXP_BUS_END(1); +@@ -159,8 +452,335 @@ + avila_pata_data.cs1_cfg = IXP4XX_EXP_CS2; + + platform_device_register(&avila_pata); ++} ++ ++static void __init avila_gw2353_setup(void) ++{ ++ platform_device_register(&avila_npeb_device); ++ platform_device_register(&avila_gpio_leds_device); ++} ++ ++static void __init avila_gw2355_setup(void) ++{ ++ avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR; ++ avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */ ++ platform_device_register(&avila_npeb_device); ++ ++ avila_npec_data.phy = 16; ++ platform_device_register(&avila_npec_device); ++ ++ avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO; ++ platform_device_register(&avila_gpio_leds_device); ++ ++ *IXP4XX_EXP_CS4 |= 0xbfff3c03; ++ avila_latch_leds[0].name = "RXD"; ++ avila_latch_leds[1].name = "TXD"; ++ avila_latch_leds[2].name = "POL"; ++ avila_latch_leds[3].name = "LNK"; ++ avila_latch_leds[4].name = "ERR"; ++ avila_latch_leds_data.num_leds = 5; ++ avila_latch_leds_data.mem = 0x54000000; ++ platform_device_register(&avila_latch_leds_device); ++ ++ avila_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1); ++ avila_pata_resources[0].end = IXP4XX_EXP_BUS_END(1); ++ ++ avila_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(2); ++ avila_pata_resources[1].end = IXP4XX_EXP_BUS_END(2); ++ ++ avila_pata_data.cs0_cfg = IXP4XX_EXP_CS1; ++ avila_pata_data.cs1_cfg = IXP4XX_EXP_CS2; ++ ++ platform_device_register(&avila_pata); ++} ++ ++static void __init avila_gw2357_setup(void) ++{ ++ platform_device_register(&avila_npeb_device); ++ ++ avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO; ++ platform_device_register(&avila_gpio_leds_device); ++ ++ *IXP4XX_EXP_CS1 |= 0xbfff3c03; ++ platform_device_register(&avila_latch_leds_device); ++} ++ ++static void __init avila_gw2365_setup(void) ++{ ++ avila_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS4 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO0, IRQ_TYPE_EDGE_RISING); ++ avila_optional_uart_data[0].mapbase = 0x54000000; ++ avila_optional_uart_data[0].membase = (void __iomem *)ioremap(0x54000000, 0x0fff); ++ avila_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO0; ++ ++ *IXP4XX_EXP_CS5 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_EDGE_RISING); ++ avila_optional_uart_data[1].mapbase = 0x55000000; ++ avila_optional_uart_data[1].membase = (void __iomem *)ioremap(0x55000000, 0x0fff); ++ avila_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO1; ++ ++ *IXP4XX_EXP_CS6 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO2, IRQ_TYPE_EDGE_RISING); ++ avila_optional_uart_data[2].mapbase = 0x56000000; ++ avila_optional_uart_data[2].membase = (void __iomem *)ioremap(0x56000000, 0x0fff); ++ avila_optional_uart_data[2].irq = IRQ_IXP4XX_GPIO2; ++ ++ *IXP4XX_EXP_CS7 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING); ++ avila_optional_uart_data[3].mapbase = 0x57000000; ++ avila_optional_uart_data[3].membase = (void __iomem *)ioremap(0x57000000, 0x0fff); ++ avila_optional_uart_data[3].irq = IRQ_IXP4XX_GPIO3; ++ ++ platform_device_register(&avila_optional_uart); ++ ++ avila_npeb_data.phy = 1; ++ platform_device_register(&avila_npeb_device); ++ ++ avila_npec_data.phy = 2; ++ platform_device_register(&avila_npec_device); ++ ++ avila_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2); ++ avila_pata_resources[0].end = IXP4XX_EXP_BUS_END(2); ++ ++ avila_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3); ++ avila_pata_resources[1].end = IXP4XX_EXP_BUS_END(3); ++ ++ avila_pata_data.cs0_cfg = IXP4XX_EXP_CS2; ++ avila_pata_data.cs1_cfg = IXP4XX_EXP_CS3; ++ ++ platform_device_register(&avila_pata); ++ ++ avila_gpio_leds[0].gpio = 109; ++ avila_gpio_leds_data.num_leds = 5; ++ platform_device_register(&avila_gpio_leds_device); ++ ++ setup_audio_devices(); ++} ++ ++static void __init avila_gw2369_setup(void) ++{ ++ avila_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ avila_npeb_data.phy = 1; ++ platform_device_register(&avila_npeb_device); ++ ++ avila_npec_data.phy = 2; ++ platform_device_register(&avila_npec_device); ++ ++ setup_audio_devices(); ++} ++ ++static void __init avila_gw2370_setup(void) ++{ ++ avila_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ avila_npeb_data.phy = 5; ++ platform_device_register(&avila_npeb_device); ++ ++ avila_npec_data.phy = IXP4XX_ETH_PHY_MAX_ADDR; ++ avila_npec_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */ ++ platform_device_register(&avila_npec_device); ++ ++ *IXP4XX_EXP_CS2 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO2, IRQ_TYPE_EDGE_RISING); ++ avila_optional_uart_data[0].mapbase = 0x52000000; ++ avila_optional_uart_data[0].membase = (void __iomem *)ioremap(0x52000000, 0x0fff); ++ avila_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO2; ++ ++ *IXP4XX_EXP_CS3 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING); ++ avila_optional_uart_data[1].mapbase = 0x53000000; ++ avila_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53000000, 0x0fff); ++ avila_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO3; ++ ++ avila_optional_uart.num_resources = 2; ++ ++ platform_device_register(&avila_optional_uart); ++ ++ avila_gpio_leds[0].gpio = 101; ++ platform_device_register(&avila_gpio_leds_device); ++ ++ setup_audio_devices(); ++} ++ ++static void __init avila_gw2375_setup(void) ++{ ++ avila_npeb_data.phy = 1; ++ platform_device_register(&avila_npeb_device); ++ ++ avila_npec_data.phy = 2; ++ platform_device_register(&avila_npec_device); ++ ++ *IXP4XX_EXP_CS2 = 0xBFFF3C43; ++ irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_EDGE_RISING); ++ avila_optional_uart_data[0].mapbase = 0x52000000; ++ avila_optional_uart_data[0].membase = (void __iomem *)ioremap(0x52000000, 0x0fff); ++ avila_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO10; ++ ++ avila_optional_uart.num_resources = 1; ++ ++ platform_device_register(&avila_optional_uart); ++ ++ setup_audio_devices(); ++} ++ ++ ++static struct avila_board_info avila_boards[] __initdata = { ++ { ++ .model = "GW2342", ++ .setup = avila_gw2342_setup, ++ }, { ++ .model = "GW2345", ++ .setup = avila_gw2345_setup, ++ }, { ++ .model = "GW2347", ++ .setup = avila_gw2347_setup, ++ }, { ++ .model = "GW2348", ++ .setup = avila_gw2348_setup, ++ }, { ++ .model = "GW2353", ++ .setup = avila_gw2353_setup, ++ }, { ++ .model = "GW2355", ++ .setup = avila_gw2355_setup, ++ }, { ++ .model = "GW2357", ++ .setup = avila_gw2357_setup, ++ }, { ++ .model = "GW2365", ++ .setup = avila_gw2365_setup, ++ }, { ++ .model = "GW2369", ++ .setup = avila_gw2369_setup, ++ }, { ++ .model = "GW2370", ++ .setup = avila_gw2370_setup, ++ }, { ++ .model = "GW2373", ++ .setup = avila_gw2369_setup, ++ }, { ++ .model = "GW2375", ++ .setup = avila_gw2375_setup, ++ } ++}; ++ ++static struct avila_board_info * __init avila_find_board_info(char *model) ++{ ++ int i; ++ model[6] = '\0'; ++ ++ for (i = 0; i < ARRAY_SIZE(avila_boards); i++) { ++ struct avila_board_info *info = &avila_boards[i]; ++ if (strcmp(info->model, model) == 0) ++ return info; ++ } ++ ++ return NULL; ++} ++ ++static struct memory_accessor *at24_mem_acc; ++ ++static void at24_setup(struct memory_accessor *mem_acc, void *context) ++{ ++ char mac_addr[ETH_ALEN]; ++ char model[7]; ++ ++ at24_mem_acc = mem_acc; ++ ++ /* Read MAC addresses */ ++ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x0, 6) == 6) { ++ memcpy(&avila_npeb_data.hwaddr, mac_addr, ETH_ALEN); ++ } ++ if (at24_mem_acc->read(at24_mem_acc, mac_addr, 0x6, 6) == 6) { ++ memcpy(&avila_npec_data.hwaddr, mac_addr, ETH_ALEN); ++ } ++ ++ /* Read the first 6 bytes of the model number */ ++ if (at24_mem_acc->read(at24_mem_acc, model, 0x20, 6) == 6) { ++ avila_info = avila_find_board_info(model); ++ } ++ ++} ++ ++static struct at24_platform_data avila_eeprom_info = { ++ .byte_len = 1024, ++ .page_size = 16, ++// .flags = AT24_FLAG_READONLY, ++ .setup = at24_setup, ++}; ++ ++static struct pca953x_platform_data avila_pca_data = { ++ .gpio_base = 100, ++}; ++ ++static struct i2c_board_info __initdata avila_i2c_board_info[] = { ++ { ++ I2C_BOARD_INFO("ds1672", 0x68), ++ }, ++ { ++ I2C_BOARD_INFO("gsp", 0x29), ++ }, ++ { ++ I2C_BOARD_INFO("pca9555", 0x23), ++ .platform_data = &avila_pca_data, ++ }, ++ { ++ I2C_BOARD_INFO("ad7418", 0x28), ++ }, ++ { ++ I2C_BOARD_INFO("24c08", 0x51), ++ .platform_data = &avila_eeprom_info ++ }, ++ { ++ I2C_BOARD_INFO("tlv320aic33", 0x1b), ++ }, ++ { ++ I2C_BOARD_INFO("tlv320aic33", 0x1a), ++ }, ++ { ++ I2C_BOARD_INFO("tlv320aic33", 0x19), ++ }, ++ { ++ I2C_BOARD_INFO("tlv320aic33", 0x18), ++ }, ++}; ++ ++static void __init avila_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ platform_add_devices(avila_devices, ARRAY_SIZE(avila_devices)); ++ ++ i2c_register_board_info(0, avila_i2c_board_info, ++ ARRAY_SIZE(avila_i2c_board_info)); ++} ++ ++static int __init avila_model_setup(void) ++{ ++ if (!machine_is_avila()) ++ return 0; ++ ++ /* default 16MB flash */ ++ avila_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ avila_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1; ++ ++ if (avila_info) { ++ printk(KERN_DEBUG "Running on Gateworks Avila %s\n", ++ avila_info->model); ++ avila_info->setup(); ++ } else { ++ printk(KERN_INFO "Unknown/missing Avila model number" ++ " -- defaults will be used\n"); ++ avila_gw23xx_setup(); ++ } ++ platform_device_register(&avila_flash); + ++ return 0; + } ++late_initcall(avila_model_setup); + + MACHINE_START(AVILA, "Gateworks Avila Network Platform") + /* Maintainer: Deepak Saxena <dsaxena@plexity.net> */ diff --git a/target/linux/ixp4xx/patches-3.14/304-ixp4xx_eth_jumboframe.patch b/target/linux/ixp4xx/patches-3.14/304-ixp4xx_eth_jumboframe.patch new file mode 100644 index 0000000..0ac595c --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/304-ixp4xx_eth_jumboframe.patch @@ -0,0 +1,80 @@ +--- a/drivers/net/ethernet/xscale/ixp4xx_eth.c ++++ b/drivers/net/ethernet/xscale/ixp4xx_eth.c +@@ -57,7 +57,7 @@ + + #define POOL_ALLOC_SIZE (sizeof(struct desc) * (RX_DESCS + TX_DESCS)) + #define REGS_SIZE 0x1000 +-#define MAX_MRU 1536 /* 0x600 */ ++#define MAX_MRU (14320 - ETH_HLEN - ETH_FCS_LEN) + #define RX_BUFF_SIZE ALIGN((NET_IP_ALIGN) + MAX_MRU, 4) + + #define NAPI_WEIGHT 16 +@@ -1319,6 +1319,32 @@ static void destroy_queues(struct port * + } + } + ++static int eth_do_change_mtu(struct net_device *dev, int mtu) ++{ ++ struct port *port; ++ struct msg msg; ++ /* adjust for ethernet headers */ ++ int framesize = mtu + ETH_HLEN + ETH_FCS_LEN; ++ ++ port = netdev_priv(dev); ++ ++ memset(&msg, 0, sizeof(msg)); ++ msg.cmd = NPE_SETMAXFRAMELENGTHS; ++ msg.eth_id = port->id; ++ ++ /* max rx/tx 64 byte blocks */ ++ msg.byte2 = ((framesize + 63) / 64) << 8; ++ msg.byte3 = ((framesize + 63) / 64) << 8; ++ ++ msg.byte4 = msg.byte6 = framesize >> 8; ++ msg.byte5 = msg.byte7 = framesize & 0xff; ++ ++ if (npe_send_recv_message(port->npe, &msg, "ETH_SET_MAX_FRAME_LENGTH")) ++ return -EIO; ++ ++ return 0; ++} ++ + static int eth_open(struct net_device *dev) + { + struct port *port = netdev_priv(dev); +@@ -1370,6 +1396,8 @@ static int eth_open(struct net_device *d + if (npe_send_recv_message(port->npe, &msg, "ETH_SET_FIREWALL_MODE")) + return -EIO; + ++ eth_do_change_mtu(dev, dev->mtu); ++ + if ((err = request_queues(port)) != 0) + return err; + +@@ -1509,7 +1537,26 @@ static int eth_close(struct net_device * + return 0; + } + ++static int ixp_eth_change_mtu(struct net_device *dev, int mtu) ++{ ++ int ret; ++ ++ if (mtu > MAX_MRU) ++ return -EINVAL; ++ ++ if (dev->flags & IFF_UP) { ++ ret = eth_do_change_mtu(dev, mtu); ++ if (ret < 0) ++ return ret; ++ } ++ ++ dev->mtu = mtu; ++ ++ return 0; ++} ++ + static const struct net_device_ops ixp4xx_netdev_ops = { ++ .ndo_change_mtu = ixp_eth_change_mtu, + .ndo_open = eth_open, + .ndo_stop = eth_close, + .ndo_start_xmit = eth_xmit, diff --git a/target/linux/ixp4xx/patches-3.14/310-gtwx5717_spi_bus.patch b/target/linux/ixp4xx/patches-3.14/310-gtwx5717_spi_bus.patch new file mode 100644 index 0000000..080b96a --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/310-gtwx5717_spi_bus.patch @@ -0,0 +1,52 @@ +--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c ++++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c +@@ -27,6 +27,7 @@ + #include <linux/serial.h> + #include <linux/tty.h> + #include <linux/serial_8250.h> ++#include <linux/spi/spi_gpio_old.h> + #include <asm/types.h> + #include <asm/setup.h> + #include <asm/memory.h> +@@ -146,9 +147,41 @@ static struct platform_device gtwx5715_f + .resource = >wx5715_flash_resource, + }; + ++static int gtwx5715_spi_boardinfo_setup(struct spi_board_info *bi, ++ struct spi_master *master, void *data) ++{ ++ ++ strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias)); ++ ++ bi->max_speed_hz = 5000000 /* Hz */; ++ bi->bus_num = master->bus_num; ++ bi->mode = SPI_MODE_0; ++ ++ return 0; ++} ++ ++static struct spi_gpio_platform_data gtwx5715_spi_bus_data = { ++ .pin_cs = GTWX5715_KSSPI_SELECT, ++ .pin_clk = GTWX5715_KSSPI_CLOCK, ++ .pin_miso = GTWX5715_KSSPI_RXD, ++ .pin_mosi = GTWX5715_KSSPI_TXD, ++ .cs_activelow = 1, ++ .no_spi_delay = 1, ++ .boardinfo_setup = gtwx5715_spi_boardinfo_setup, ++}; ++ ++static struct platform_device gtwx5715_spi_bus = { ++ .name = "spi-gpio", ++ .id = 0, ++ .dev = { ++ .platform_data = >wx5715_spi_bus_data, ++ }, ++}; ++ + static struct platform_device *gtwx5715_devices[] __initdata = { + >wx5715_uart_device, + >wx5715_flash, ++ >wx5715_spi_bus, + }; + + static void __init gtwx5715_init(void) diff --git a/target/linux/ixp4xx/patches-3.14/311-gtwx5717_mac_plat_info.patch b/target/linux/ixp4xx/patches-3.14/311-gtwx5717_mac_plat_info.patch new file mode 100644 index 0000000..aa7a9e0 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/311-gtwx5717_mac_plat_info.patch @@ -0,0 +1,50 @@ +--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c ++++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c +@@ -28,6 +28,7 @@ + #include <linux/tty.h> + #include <linux/serial_8250.h> + #include <linux/spi/spi_gpio_old.h> ++#include <linux/dma-mapping.h> + #include <asm/types.h> + #include <asm/setup.h> + #include <asm/memory.h> +@@ -178,10 +179,39 @@ static struct platform_device gtwx5715_s + }, + }; + ++static struct eth_plat_info gtwx5715_npeb_data = { ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0x1e, /* ports 1-4 of the KS8995 switch */ ++ .rxq = 3, ++ .txreadyq = 20, ++}; ++ ++static struct eth_plat_info gtwx5715_npec_data = { ++ .phy = 5, /* port 5 of the KS8995 switch */ ++ .rxq = 4, ++ .txreadyq = 21, ++}; ++ ++static struct platform_device gtwx5715_npeb_device = { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = >wx5715_npeb_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++}; ++ ++static struct platform_device gtwx5715_npec_device = { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = >wx5715_npec_data, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++}; ++ + static struct platform_device *gtwx5715_devices[] __initdata = { + >wx5715_uart_device, + >wx5715_flash, + >wx5715_spi_bus, ++ >wx5715_npeb_device, ++ >wx5715_npec_device, + }; + + static void __init gtwx5715_init(void) diff --git a/target/linux/ixp4xx/patches-3.14/312-ixp4xx_pata_optimization.patch b/target/linux/ixp4xx/patches-3.14/312-ixp4xx_pata_optimization.patch new file mode 100644 index 0000000..59c2837 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/312-ixp4xx_pata_optimization.patch @@ -0,0 +1,137 @@ +--- a/drivers/ata/pata_ixp4xx_cf.c ++++ b/drivers/ata/pata_ixp4xx_cf.c +@@ -24,16 +24,58 @@ + #include <scsi/scsi_host.h> + + #define DRV_NAME "pata_ixp4xx_cf" +-#define DRV_VERSION "0.2" ++#define DRV_VERSION "0.3" + + static int ixp4xx_set_mode(struct ata_link *link, struct ata_device **error) + { ++ struct ixp4xx_pata_data *data = link->ap->host->dev->platform_data; ++ unsigned int pio_mask; + struct ata_device *dev; + + ata_for_each_dev(dev, link, ENABLED) { +- ata_dev_info(dev, "configured for PIO0\n"); +- dev->pio_mode = XFER_PIO_0; +- dev->xfer_mode = XFER_PIO_0; ++ if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)) { ++ pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03; ++ if (pio_mask & (1 << 1)) { ++ pio_mask = 4; ++ } else { ++ pio_mask = 3; ++ } ++ } else { ++ pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8); ++ } ++ ++ switch (pio_mask){ ++ case 0: ++ ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n"); ++ dev->pio_mode = XFER_PIO_0; ++ dev->xfer_mode = XFER_PIO_0; ++ *data->cs0_cfg = 0x8a473c03; ++ break; ++ case 1: ++ ata_dev_printk(dev, KERN_INFO, "configured for PIO1\n"); ++ dev->pio_mode = XFER_PIO_1; ++ dev->xfer_mode = XFER_PIO_1; ++ *data->cs0_cfg = 0x86433c03; ++ break; ++ case 2: ++ ata_dev_printk(dev, KERN_INFO, "configured for PIO2\n"); ++ dev->pio_mode = XFER_PIO_2; ++ dev->xfer_mode = XFER_PIO_2; ++ *data->cs0_cfg = 0x82413c03; ++ break; ++ case 3: ++ ata_dev_printk(dev, KERN_INFO, "configured for PIO3\n"); ++ dev->pio_mode = XFER_PIO_3; ++ dev->xfer_mode = XFER_PIO_3; ++ *data->cs0_cfg = 0x80823c03; ++ break; ++ case 4: ++ ata_dev_printk(dev, KERN_INFO, "configured for PIO4\n"); ++ dev->pio_mode = XFER_PIO_4; ++ dev->xfer_mode = XFER_PIO_4; ++ *data->cs0_cfg = 0x80403c03; ++ break; ++ } + dev->xfer_shift = ATA_SHIFT_PIO; + dev->flags |= ATA_DFLAG_PIO; + } +@@ -46,6 +88,7 @@ static unsigned int ixp4xx_mmio_data_xfe + unsigned int i; + unsigned int words = buflen >> 1; + u16 *buf16 = (u16 *) buf; ++ unsigned int pio_mask; + struct ata_port *ap = dev->link->ap; + void __iomem *mmio = ap->ioaddr.data_addr; + struct ixp4xx_pata_data *data = dev_get_platdata(ap->host->dev); +@@ -53,8 +96,34 @@ static unsigned int ixp4xx_mmio_data_xfe + /* set the expansion bus in 16bit mode and restore + * 8 bit mode after the transaction. + */ +- *data->cs0_cfg &= ~(0x01); +- udelay(100); ++ if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)){ ++ pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03; ++ if (pio_mask & (1 << 1)){ ++ pio_mask = 4; ++ }else{ ++ pio_mask = 3; ++ } ++ }else{ ++ pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8); ++ } ++ switch (pio_mask){ ++ case 0: ++ *data->cs0_cfg = 0xa9643c42; ++ break; ++ case 1: ++ *data->cs0_cfg = 0x85033c42; ++ break; ++ case 2: ++ *data->cs0_cfg = 0x80b23c42; ++ break; ++ case 3: ++ *data->cs0_cfg = 0x80823c42; ++ break; ++ case 4: ++ *data->cs0_cfg = 0x80403c42; ++ break; ++ } ++ udelay(5); + + /* Transfer multiple of 2 bytes */ + if (rw == READ) +@@ -79,8 +148,24 @@ static unsigned int ixp4xx_mmio_data_xfe + words++; + } + +- udelay(100); +- *data->cs0_cfg |= 0x01; ++ udelay(5); ++ switch (pio_mask){ ++ case 0: ++ *data->cs0_cfg = 0x8a473c03; ++ break; ++ case 1: ++ *data->cs0_cfg = 0x86433c03; ++ break; ++ case 2: ++ *data->cs0_cfg = 0x82413c03; ++ break; ++ case 3: ++ *data->cs0_cfg = 0x80823c03; ++ break; ++ case 4: ++ *data->cs0_cfg = 0x80403c03; ++ break; ++ } + + return words << 1; + } diff --git a/target/linux/ixp4xx/patches-3.14/500-usr8200_support.patch b/target/linux/ixp4xx/patches-3.14/500-usr8200_support.patch new file mode 100644 index 0000000..fb7f03e --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/500-usr8200_support.patch @@ -0,0 +1,347 @@ +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -93,6 +93,14 @@ config MACH_SIDEWINDER + Engineering Sidewinder board. For more information on this + platform, see http://www.adiengineering.com + ++config MACH_USR8200 ++ bool "USRobotics USR8200" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the USRobotics ++ USR8200 router board. For more information on this platform, see ++ http://openwrt.org ++ + config MACH_COMPEXWP18 + bool "Compex WP18 / NP18A" + select PCI +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -27,6 +27,7 @@ obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt + obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o + obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o + obj-pci-$(CONFIG_MACH_MI424WR) += mi424wr-pci.o ++obj-pci-$(CONFIG_MACH_USR8200) += usr8200-pci.o + + obj-y += common.o + +@@ -55,6 +56,7 @@ obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv + obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o + obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o + obj-$(CONFIG_MACH_MI424WR) += mi424wr-setup.o ++obj-$(CONFIG_MACH_USR8200) += usr8200-setup.o + + obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o + obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o +--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h ++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h +@@ -44,7 +44,8 @@ static __inline__ void __arch_decomp_set + machine_is_gateway7001() || machine_is_wg302v2() || + machine_is_devixp() || machine_is_miccpt() || machine_is_mic256() || + machine_is_pronghorn() || machine_is_pronghorn_metro() || +- machine_is_wrt300nv2() || machine_is_tw5334()) ++ machine_is_wrt300nv2() || machine_is_tw5334() || ++ machine_is_usr8200()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/usr8200-pci.c +@@ -0,0 +1,77 @@ ++/* ++ * arch/arch/mach-ixp4xx/usr8200-pci.c ++ * ++ * PCI setup routines for USRobotics USR8200 ++ * ++ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org> ++ * ++ * based on pronghorn-pci.c ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Peter Denison <openwrt@marshadder.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++ ++#include <asm/mach/pci.h> ++ ++void __init usr8200_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO7, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO8, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO9, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init usr8200_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == 14) ++ return IRQ_IXP4XX_GPIO7; ++ else if (slot == 15) ++ return IRQ_IXP4XX_GPIO8; ++ else if (slot == 16) { ++ if (pin == 1) ++ return IRQ_IXP4XX_GPIO11; ++ else if (pin == 2) ++ return IRQ_IXP4XX_GPIO10; ++ else if (pin == 3) ++ return IRQ_IXP4XX_GPIO9; ++ else ++ return -1; ++ } else ++ return -1; ++} ++ ++struct hw_pci usr8200_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = usr8200_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = usr8200_map_irq, ++}; ++ ++int __init usr8200_pci_init(void) ++{ ++ if (machine_is_usr8200()) ++ pci_common_init(&usr8200_pci); ++ return 0; ++} ++ ++subsys_initcall(usr8200_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/usr8200-setup.c +@@ -0,0 +1,217 @@ ++/* ++ * arch/arm/mach-ixp4xx/usr8200-setup.c ++ * ++ * Board setup for the USRobotics USR8200 ++ * ++ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org> ++ * ++ * based on pronghorn-setup.c: ++ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org> ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Peter Denison <openwrt@marshadder.org> ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++#include <linux/types.h> ++#include <linux/memory.h> ++#include <linux/i2c-gpio.h> ++#include <linux/leds.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/setup.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct flash_platform_data usr8200_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource usr8200_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device usr8200_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &usr8200_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &usr8200_flash_resource, ++}; ++ ++static struct resource usr8200_uart_resources [] = { ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ } ++}; ++ ++static struct plat_serial8250_port usr8200_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device usr8200_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = usr8200_uart_data, ++ }, ++ .num_resources = 2, ++ .resource = usr8200_uart_resources, ++}; ++ ++static struct gpio_led usr8200_led_pin[] = { ++ { ++ .name = "usr8200:usb1", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "usr8200:usb2", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "usr8200:ieee1394", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "usr8200:internal", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "usr8200:power", ++ .gpio = 14, ++ } ++}; ++ ++static struct gpio_led_platform_data usr8200_led_data = { ++ .num_leds = ARRAY_SIZE(usr8200_led_pin), ++ .leds = usr8200_led_pin, ++}; ++ ++static struct platform_device usr8200_led = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev.platform_data = &usr8200_led_data, ++}; ++ ++static struct eth_plat_info usr8200_plat_eth[] = { ++ { /* NPEC - LAN with Marvell 88E6060 switch */ ++ .phy = IXP4XX_ETH_PHY_MAX_ADDR, ++ .phy_mask = 0x0F0000, ++ .rxq = 4, ++ .txreadyq = 21, ++ }, { /* NPEB - WAN */ ++ .phy = 9, ++ .rxq = 3, ++ .txreadyq = 20, ++ } ++}; ++ ++static struct platform_device usr8200_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = usr8200_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = usr8200_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct resource usr8200_rtc_resources = { ++ .flags = IORESOURCE_MEM ++}; ++ ++static struct platform_device usr8200_rtc = { ++ .name = "rtc7301", ++ .id = 0, ++ .num_resources = 1, ++ .resource = &usr8200_rtc_resources, ++}; ++ ++static struct platform_device *usr8200_devices[] __initdata = { ++ &usr8200_flash, ++ &usr8200_uart, ++ &usr8200_led, ++ &usr8200_eth[0], ++ &usr8200_eth[1], ++ &usr8200_rtc, ++}; ++ ++static void __init usr8200_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ usr8200_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ usr8200_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1; ++ ++ usr8200_rtc_resources.start = IXP4XX_EXP_BUS_BASE(2); ++ usr8200_rtc_resources.end = IXP4XX_EXP_BUS_BASE(2) + 0x01ff; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN | ++ IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN; ++ *IXP4XX_GPIO_GPCLKR = 0x01100000; ++ ++ /* configure button as input */ ++ gpio_line_config(12, IXP4XX_GPIO_IN); ++ ++ platform_add_devices(usr8200_devices, ARRAY_SIZE(usr8200_devices)); ++} ++ ++MACHINE_START(USR8200, "USRobotics USR8200") ++ /* Maintainer: Peter Denison <openwrt@marshadder.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = usr8200_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END diff --git a/target/linux/ixp4xx/patches-3.14/520-tw2662_support.patch b/target/linux/ixp4xx/patches-3.14/520-tw2662_support.patch new file mode 100644 index 0000000..7cea61f --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/520-tw2662_support.patch @@ -0,0 +1,317 @@ +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -176,6 +176,15 @@ config ARCH_PRPMC1100 + PrPCM1100 Processor Mezanine Module. For more information on + this platform, see <file:Documentation/arm/IXP4xx>. + ++config MACH_TW2662 ++ bool "Titan Wireless TW-266-2" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support the Titan ++ Wireless TW266-2. For more information on this platform, ++ see http://openwrt.org ++ ++ + config MACH_TW5334 + bool "Titan Wireless TW-533-4" + select PCI +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -25,6 +25,7 @@ obj-pci-$(CONFIG_MACH_SIDEWINDER) += sid + obj-pci-$(CONFIG_MACH_COMPEXWP18) += ixdp425-pci.o + obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o + obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o ++obj-pci-$(CONFIG_MACH_TW2662) += tw2662-pci.o + obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o + obj-pci-$(CONFIG_MACH_MI424WR) += mi424wr-pci.o + obj-pci-$(CONFIG_MACH_USR8200) += usr8200-pci.o +@@ -54,6 +55,7 @@ obj-$(CONFIG_MACH_SIDEWINDER) += sidewin + obj-$(CONFIG_MACH_COMPEXWP18) += compex42x-setup.o + obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o + obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o ++obj-$(CONFIG_MACH_TW2662) += tw2662-setup.o + obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o + obj-$(CONFIG_MACH_MI424WR) += mi424wr-setup.o + obj-$(CONFIG_MACH_USR8200) += usr8200-setup.o +--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h ++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h +@@ -45,7 +45,7 @@ static __inline__ void __arch_decomp_set + machine_is_devixp() || machine_is_miccpt() || machine_is_mic256() || + machine_is_pronghorn() || machine_is_pronghorn_metro() || + machine_is_wrt300nv2() || machine_is_tw5334() || +- machine_is_usr8200()) ++ machine_is_usr8200() || machine_is_tw2662()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/tw2662-pci.c +@@ -0,0 +1,67 @@ ++/* ++ * arch/arm/mach-ixp4xx/tw2662-pci.c ++ * ++ * PCI setup routines for Tiran Wireless TW-266-2 platform ++ * ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com> ++ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org> ++ * ++ * Maintainer: Deepak Saxena <dsaxena@mvista.com> ++ * Maintainer: Alexandros C. Couloumbis <alex@ozo.com> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach/pci.h> ++ ++#define SLOT0_DEVID 1 ++#define SLOT1_DEVID 3 ++ ++/* PCI controller GPIO to IRQ pin mappings */ ++#define SLOT0_INTA 11 ++#define SLOT1_INTA 9 ++ ++void __init tw2662_pci_preinit(void) ++{ ++ irq_set_irq_type(IXP4XX_GPIO_IRQ(SLOT0_INTA), IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IXP4XX_GPIO_IRQ(SLOT1_INTA), IRQ_TYPE_LEVEL_LOW); ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init tw2662_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ if (slot == SLOT0_DEVID) ++ return IXP4XX_GPIO_IRQ(SLOT0_INTA); ++ else if (slot == SLOT1_DEVID) ++ return IXP4XX_GPIO_IRQ(SLOT1_INTA); ++ else return -1; ++} ++ ++struct hw_pci tw2662_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = tw2662_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = tw2662_map_irq, ++}; ++ ++int __init tw2662_pci_init(void) ++{ ++ if (machine_is_tw2662()) ++ pci_common_init(&tw2662_pci); ++ return 0; ++} ++ ++subsys_initcall(tw2662_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/tw2662-setup.c +@@ -0,0 +1,197 @@ ++/* ++ * arch/arm/mach-ixp4xx/tw2662-setup.c ++ * ++ * Titan Wireless TW-266-2 ++ * ++ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org> ++ * Copyright (C) 2010 Alexandros C. Couloumbis <alex@ozo.com> ++ * ++ * based on ap1000-setup.c: ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/if_ether.h> ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/slab.h> ++#include <linux/netdevice.h> ++#include <linux/etherdevice.h> ++#include <linux/platform_device.h> ++ ++#include <asm/io.h> ++#include <asm/types.h> ++#include <asm/setup.h> ++#include <asm/memory.h> ++#include <mach/hardware.h> ++#include <asm/mach-types.h> ++#include <asm/irq.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++/* gpio mask used by platform device */ ++#define TW2662_GPIO_MASK (1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) ++ ++static struct flash_platform_data tw2662_flash_data = { ++ .map_name = "cfi_probe", ++ .width = 2, ++}; ++ ++static struct resource tw2662_flash_resource = { ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct platform_device tw2662_flash = { ++ .name = "IXP4XX-Flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &tw2662_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &tw2662_flash_resource, ++}; ++ ++static struct resource tw2662_uart_resources[] = { ++ { ++ .start = IXP4XX_UART1_BASE_PHYS, ++ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ }, ++ { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM ++ } ++}; ++ ++static struct plat_serial8250_port tw2662_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART1_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART1, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device tw2662_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev.platform_data = tw2662_uart_data, ++ .num_resources = 2, ++ .resource = tw2662_uart_resources ++}; ++ ++/* Built-in 10/100 Ethernet MAC interfaces */ ++static struct eth_plat_info tw2662_plat_eth[] = { ++ { ++ .phy = 3, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 1, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device tw2662_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = tw2662_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = tw2662_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++ ++static struct platform_device *tw2662_devices[] __initdata = { ++ &tw2662_flash, ++ &tw2662_uart, ++ &tw2662_eth[0], ++ &tw2662_eth[1], ++}; ++ ++static char tw2662_mem_fixup[] __initdata = "mem=64M "; ++ ++static void __init tw2662_fixup(struct tag *tags, char **cmdline, ++ struct meminfo *mi) ++{ ++ struct tag *t = tags; ++ char *p = *cmdline; ++ ++ /* Find the end of the tags table, taking note of any cmdline tag. */ ++ for (; t->hdr.size; t = tag_next(t)) { ++ if (t->hdr.tag == ATAG_CMDLINE) { ++ p = t->u.cmdline.cmdline; ++ } ++ } ++ ++ /* Overwrite the end of the table with a new cmdline tag. */ ++ t->hdr.tag = ATAG_CMDLINE; ++ t->hdr.size = (sizeof (struct tag_header) + ++ strlen(tw2662_mem_fixup) + strlen(p) + 1 + 4) >> 2; ++ strlcpy(t->u.cmdline.cmdline, tw2662_mem_fixup, COMMAND_LINE_SIZE); ++ strlcpy(t->u.cmdline.cmdline + strlen(tw2662_mem_fixup), p, ++ COMMAND_LINE_SIZE - strlen(tw2662_mem_fixup)); ++ ++ /* Terminate the table. */ ++ t = tag_next(t); ++ t->hdr.tag = ATAG_NONE; ++ t->hdr.size = 0; ++} ++ ++static void __init tw2662_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ tw2662_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ tw2662_flash_resource.end = ++ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; ++ ++ platform_add_devices(tw2662_devices, ARRAY_SIZE(tw2662_devices)); ++ ++ if (!(is_valid_ether_addr(tw2662_plat_eth[0].hwaddr))) ++ random_ether_addr(tw2662_plat_eth[0].hwaddr); ++ if (!(is_valid_ether_addr(tw2662_plat_eth[1].hwaddr))) { ++ memcpy(tw2662_plat_eth[1].hwaddr, tw2662_plat_eth[0].hwaddr, ETH_ALEN); ++ tw2662_plat_eth[1].hwaddr[5] = (tw2662_plat_eth[0].hwaddr[5] + 1); ++ } ++ ++} ++ ++#ifdef CONFIG_MACH_TW2662 ++MACHINE_START(TW2662, "Titan Wireless TW-266-2") ++ /* Maintainer: Alexandros C. Couloumbis <alex@ozo.com> */ ++ .fixup = tw2662_fixup, ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x0100, ++ .init_machine = tw2662_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++#endif diff --git a/target/linux/ixp4xx/patches-3.14/530-ap42x_support.patch b/target/linux/ixp4xx/patches-3.14/530-ap42x_support.patch new file mode 100644 index 0000000..1afbe3d --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/530-ap42x_support.patch @@ -0,0 +1,282 @@ +--- a/arch/arm/mach-ixp4xx/Kconfig ++++ b/arch/arm/mach-ixp4xx/Kconfig +@@ -4,6 +4,14 @@ menu "Intel IXP4xx Implementation Option + + comment "IXP4xx Platforms" + ++config MACH_AP42X ++ bool "Tonze AP-422/425" ++ select PCI ++ help ++ Say 'Y' here if you want your kernel to support Tonze's ++ AP-422/425 boards. For more information on this platform, ++ see http://tonze.com.tw ++ + config MACH_NSLU2 + bool + prompt "Linksys NSLU2" +--- a/arch/arm/mach-ixp4xx/Makefile ++++ b/arch/arm/mach-ixp4xx/Makefile +@@ -5,6 +5,7 @@ + obj-pci-y := + obj-pci-n := + ++obj-pci-$(CONFIG_MACH_AP42X) += ap42x-pci.o + obj-pci-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o + obj-pci-$(CONFIG_MACH_AVILA) += avila-pci.o + obj-pci-$(CONFIG_MACH_CAMBRIA) += cambria-pci.o +@@ -32,6 +33,7 @@ obj-pci-$(CONFIG_MACH_USR8200) += usr82 + + obj-y += common.o + ++obj-$(CONFIG_MACH_AP42X) += ap42x-setup.o + obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-setup.o + obj-$(CONFIG_MACH_AVILA) += avila-setup.o + obj-$(CONFIG_MACH_CAMBRIA) += cambria-setup.o +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/ap42x-pci.c +@@ -0,0 +1,63 @@ ++/* ++ * arch/arch/mach-ixp4xx/ap42x-pci.c ++ * ++ * PCI setup routines for Tonze AP-422/425 ++ * ++ * Copyright (C) 2012 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-pci.c: ++ * Copyright (C) 2002 Jungo Software Technologies. ++ * Copyright (C) 2003 MontaVista Softwrae, Inc. ++ * ++ * Maintainer: Imre Kaloz <kaloz@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/pci.h> ++#include <linux/init.h> ++#include <linux/irq.h> ++ ++#include <asm/mach-types.h> ++#include <mach/hardware.h> ++ ++#include <asm/mach/pci.h> ++ ++void __init ap42x_pci_preinit(void) ++{ ++ irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW); ++ irq_set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW); ++ ++ ixp4xx_pci_preinit(); ++} ++ ++static int __init ap42x_map_irq(const struct pci_dev *dev, u8 slot, ++ u8 pin) ++{ ++ if (slot == 1) ++ return IRQ_IXP4XX_GPIO11; ++ else if (slot == 2) ++ return IRQ_IXP4XX_GPIO10; ++ else return -1; ++} ++ ++struct hw_pci ap42x_pci __initdata = { ++ .nr_controllers = 1, ++ .preinit = ap42x_pci_preinit, ++ .ops = &ixp4xx_ops, ++ .setup = ixp4xx_setup, ++ .map_irq = ap42x_map_irq, ++}; ++ ++int __init ap42x_pci_init(void) ++{ ++ if (machine_is_ap42x()) ++ pci_common_init(&ap42x_pci); ++ return 0; ++} ++ ++subsys_initcall(ap42x_pci_init); +--- /dev/null ++++ b/arch/arm/mach-ixp4xx/ap42x-setup.c +@@ -0,0 +1,166 @@ ++/* ++ * arch/arm/mach-ixp4xx/ap42x-setup.c ++ * ++ * Board setup for the Tonze AP-42x boards ++ * ++ * Copyright (C) 2012 Imre Kaloz <kaloz@openwrt.org> ++ * ++ * based on coyote-setup.c: ++ * Copyright (C) 2003-2005 MontaVista Software, Inc. ++ * ++ * Author: Imre Kaloz <Kaloz@openwrt.org> ++ */ ++ ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/device.h> ++#include <linux/serial.h> ++#include <linux/tty.h> ++#include <linux/serial_8250.h> ++#include <linux/mtd/physmap.h> ++#include <linux/dma-mapping.h> ++ ++#include <asm/types.h> ++#include <asm/setup.h> ++#include <asm/memory.h> ++#include <mach/hardware.h> ++#include <asm/irq.h> ++#include <asm/mach-types.h> ++#include <asm/mach/arch.h> ++#include <asm/mach/flash.h> ++ ++static struct mtd_partition ap42x_flash_partitions[] = { ++ { ++ .name = "RedBoot", ++ .offset = 0x00000000, ++ .size = 0x00080000, ++ }, { ++ .name = "linux", ++ .offset = 0x00080000, ++ .size = 0x00100000, ++ }, { ++ .name = "rootfs", ++ .offset = 0x00180000, ++ .size = 0x00660000, ++ }, { ++ .name = "FIS directory", ++ .offset = 0x007f8000, ++ .size = 0x00007000, ++ }, { ++ .name = "RedBoot config", ++ .offset = 0x007ff000, ++ .size = 0x00001000, ++ }, ++}; ++ ++static struct physmap_flash_data ap42x_flash_data = { ++ .width = 2, ++ .parts = ap42x_flash_partitions, ++ .nr_parts = ARRAY_SIZE(ap42x_flash_partitions), ++}; ++ ++static struct resource ap42x_flash_resource = { ++ .flags = IORESOURCE_MEM, ++ .start = IXP4XX_EXP_BUS_BASE_PHYS, ++ .end = IXP4XX_EXP_BUS_BASE_PHYS + SZ_8M - 1, ++}; ++ ++static struct platform_device ap42x_flash = { ++ .name = "physmap-flash", ++ .id = 0, ++ .dev = { ++ .platform_data = &ap42x_flash_data, ++ }, ++ .num_resources = 1, ++ .resource = &ap42x_flash_resource, ++}; ++ ++static struct resource ap42x_uart_resource = { ++ .start = IXP4XX_UART2_BASE_PHYS, ++ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct plat_serial8250_port ap42x_uart_data[] = { ++ { ++ .mapbase = IXP4XX_UART2_BASE_PHYS, ++ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, ++ .irq = IRQ_IXP4XX_UART2, ++ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, ++ .iotype = UPIO_MEM, ++ .regshift = 2, ++ .uartclk = IXP4XX_UART_XTAL, ++ }, ++ { }, ++}; ++ ++static struct platform_device ap42x_uart = { ++ .name = "serial8250", ++ .id = PLAT8250_DEV_PLATFORM, ++ .dev = { ++ .platform_data = ap42x_uart_data, ++ }, ++ .num_resources = 1, ++ .resource = &ap42x_uart_resource, ++}; ++ ++static struct eth_plat_info ap42x_plat_eth[] = { ++ { ++ .phy = 2, ++ .rxq = 3, ++ .txreadyq = 20, ++ }, { ++ .phy = 1, ++ .rxq = 4, ++ .txreadyq = 21, ++ } ++}; ++ ++static struct platform_device ap42x_eth[] = { ++ { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEB, ++ .dev.platform_data = ap42x_plat_eth, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ }, { ++ .name = "ixp4xx_eth", ++ .id = IXP4XX_ETH_NPEC, ++ .dev.platform_data = ap42x_plat_eth + 1, ++ .dev.coherent_dma_mask = DMA_BIT_MASK(32), ++ } ++}; ++ ++static struct platform_device *ap42x_devices[] __initdata = { ++ &ap42x_flash, ++ &ap42x_uart, ++ &ap42x_eth[0], ++ &ap42x_eth[1], ++}; ++ ++static void __init ap42x_init(void) ++{ ++ ixp4xx_sys_init(); ++ ++ ap42x_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); ++ ap42x_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1; ++ ++ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE; ++ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0; ++ ++ platform_add_devices(ap42x_devices, ARRAY_SIZE(ap42x_devices)); ++} ++ ++#ifdef CONFIG_MACH_AP42X ++MACHINE_START(AP42X, "Tonze AP-422/425") ++ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */ ++ .map_io = ixp4xx_map_io, ++ .init_irq = ixp4xx_init_irq, ++ .init_time = ixp4xx_timer_init, ++ .atag_offset = 0x100, ++ .init_machine = ap42x_init, ++#if defined(CONFIG_PCI) ++ .dma_zone_size = SZ_64M, ++#endif ++ .restart = ixp4xx_restart, ++MACHINE_END ++#endif +--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h ++++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h +@@ -45,7 +45,8 @@ static __inline__ void __arch_decomp_set + machine_is_devixp() || machine_is_miccpt() || machine_is_mic256() || + machine_is_pronghorn() || machine_is_pronghorn_metro() || + machine_is_wrt300nv2() || machine_is_tw5334() || +- machine_is_usr8200() || machine_is_tw2662()) ++ machine_is_usr8200() || machine_is_tw2662() || ++ machine_is_ap42x()) + uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS; + else + uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS; diff --git a/target/linux/ixp4xx/patches-3.14/600-skb_avoid_dmabounce.patch b/target/linux/ixp4xx/patches-3.14/600-skb_avoid_dmabounce.patch new file mode 100644 index 0000000..2e4c75e --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/600-skb_avoid_dmabounce.patch @@ -0,0 +1,23 @@ +--- a/net/core/skbuff.c ++++ b/net/core/skbuff.c +@@ -210,6 +210,9 @@ struct sk_buff *__alloc_skb(unsigned int + + if (sk_memalloc_socks() && (flags & SKB_ALLOC_RX)) + gfp_mask |= __GFP_MEMALLOC; ++#ifdef CONFIG_ARCH_IXP4XX ++ gfp_mask |= GFP_DMA; ++#endif + + /* Get the HEAD */ + skb = kmem_cache_alloc_node(cache, gfp_mask & ~__GFP_DMA, node); +@@ -1057,6 +1060,10 @@ int pskb_expand_head(struct sk_buff *skb + if (skb_shared(skb)) + BUG(); + ++#ifdef CONFIG_ARCH_IXP4XX ++ gfp_mask |= GFP_DMA; ++#endif ++ + size = SKB_DATA_ALIGN(size); + + if (skb_pfmemalloc(skb)) diff --git a/target/linux/ixp4xx/patches-3.14/900-ixp4xx-crypto-include-module.h.patch b/target/linux/ixp4xx/patches-3.14/900-ixp4xx-crypto-include-module.h.patch new file mode 100644 index 0000000..24c93dc --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/900-ixp4xx-crypto-include-module.h.patch @@ -0,0 +1,10 @@ +--- a/drivers/crypto/ixp4xx_crypto.c ++++ b/drivers/crypto/ixp4xx_crypto.c +@@ -14,6 +14,7 @@ + #include <linux/dmapool.h> + #include <linux/crypto.h> + #include <linux/kernel.h> ++#include <linux/module.h> + #include <linux/rtnetlink.h> + #include <linux/interrupt.h> + #include <linux/spinlock.h> diff --git a/target/linux/ixp4xx/patches-3.14/910-ixp4xx-nr_irq_lines.patch b/target/linux/ixp4xx/patches-3.14/910-ixp4xx-nr_irq_lines.patch new file mode 100644 index 0000000..06e09f4 --- /dev/null +++ b/target/linux/ixp4xx/patches-3.14/910-ixp4xx-nr_irq_lines.patch @@ -0,0 +1,22 @@ +--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c ++++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c +@@ -53,7 +53,7 @@ static int __init ixdp425_map_irq(const + }; + + if (slot >= 1 && slot <= MAX_DEV && pin >= 1 && pin <= IRQ_LINES) +- return pci_irq_table[(slot + pin - 2) % 4]; ++ return pci_irq_table[(slot + pin - 2) % IRQ_LINES]; + + return -1; + } +--- a/arch/arm/mach-ixp4xx/miccpt-pci.c ++++ b/arch/arm/mach-ixp4xx/miccpt-pci.c +@@ -54,7 +54,7 @@ static int __init miccpt_map_irq(const s + }; + + if (slot >= 1 && slot <= MAX_DEV && pin >= 1 && pin <= IRQ_LINES) +- return pci_irq_table[(slot + pin - 2) % 4]; ++ return pci_irq_table[(slot + pin - 2) % IRQ_LINES]; + + return -1; + } |