diff options
Diffstat (limited to 'target/linux')
-rw-r--r-- | target/linux/orion/config-default | 1 | ||||
-rwxr-xr-x | target/linux/orion/files/arch/arm/mach-orion5x/dt2-common.h | 82 | ||||
-rw-r--r-- | target/linux/orion/files/arch/arm/mach-orion5x/dt2-setup.c | 445 | ||||
-rw-r--r-- | target/linux/orion/image/Makefile | 18 | ||||
-rw-r--r-- | target/linux/orion/patches/200-dt2_board_support.patch | 26 |
5 files changed, 572 insertions, 0 deletions
diff --git a/target/linux/orion/config-default b/target/linux/orion/config-default index b0971cd..ba6fb2e 100644 --- a/target/linux/orion/config-default +++ b/target/linux/orion/config-default @@ -176,6 +176,7 @@ CONFIG_LZO_COMPRESS=m CONFIG_LZO_DECOMPRESS=m # CONFIG_MACH_DB88F5281 is not set # CONFIG_MACH_DNS323 is not set +CONFIG_MACH_DT2=y # CONFIG_MACH_EDMINI_V2 is not set # CONFIG_MACH_KUROBOX_PRO is not set # CONFIG_MACH_LINKSTATION_MINI is not set diff --git a/target/linux/orion/files/arch/arm/mach-orion5x/dt2-common.h b/target/linux/orion/files/arch/arm/mach-orion5x/dt2-common.h new file mode 100755 index 0000000..a54e188 --- /dev/null +++ b/target/linux/orion/files/arch/arm/mach-orion5x/dt2-common.h @@ -0,0 +1,82 @@ +#ifndef __INC_DT2_COMMON_H +#define __INC_DT2_COMMON_H + +#define ATAG_MV_UBOOT 0x41000403 + +struct tag_mv_uboot { + u32 uboot_version; + u32 tclk; + u32 sysclk; + u32 isUsbHost; + u32 overEthAddr; + u8 dt2_eeprom[256]; +}; + +#define DT2_EEPROM_ADDR 0x50 +#define DT2_EEPROM_OFFSET 0 +#define DT2_EEPROM_LENGTH 256 + +#define DT2_SERIAL_NUMBER_DEFAULT "run on default\0" +#define DT2_REVISION_DEFAULT_INIT 0xFF +#define DT2_CONFIG_FLAGS_DEFAULT 0x00 + +#define _PACKED_ __attribute__((packed)) + +struct DT2_EEPROM_SD_CONFIG { + unsigned int ram_1; + unsigned int ram_2; + unsigned int ram_3; + unsigned int ram_4; + unsigned char ram_5; + unsigned char ram_6; + unsigned short ram_7; + unsigned int magic_id; + } _PACKED_; // 24 Bytes in total + +struct DT2_EEPROM_FC_CONFIG { + unsigned char rtc_sts_mask; + unsigned char rtc_sts_init; + unsigned char rtc_int_mask; + unsigned char rtc_int_init; + unsigned char rtc_atrim_init; + unsigned char rtc_dtrim_init; + unsigned char dummy1; + unsigned char dummy2; + unsigned char dt2_config_flags; /* 0x80 to load rtc_values to RTC */ + unsigned char dt2_revision; /* upper nibble is HW, lower nibble is FW */ + unsigned char dt2_serial_number[16]; /* Serial number of DT-2 */ + } _PACKED_; // 26 Bytes in total + +#define CFG_LOAD_RTC_VALUES 0x80 + +struct DT2_EEPROM_GW_CONFIG { + unsigned int dummy1; + unsigned int dummy2; + unsigned int dummy3; + unsigned char dummy4; + unsigned char tos_video_val1; + unsigned char tos_video_val2; + unsigned char tos_voip_val; + unsigned char qos_igmp_cfg; + unsigned char num_of_ifs; + unsigned short vlan_ports_if[3]; + unsigned char mac_addr[3][6]; + } _PACKED_; // 42 Bytes in total + +#define _SIZE_OF_ALL_STRUCTS_ (sizeof(struct DT2_EEPROM_SD_CONFIG) + sizeof(struct DT2_EEPROM_FC_CONFIG) + sizeof(struct DT2_EEPROM_GW_CONFIG)) + +// MV = EEPROM - SD - FC - GW - CRC +struct DT2_EEPROM_MV_CONFIG { + unsigned int reg_addr[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)]; + unsigned int reg_data[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)]; + } _PACKED_; + +struct DT2_EEPROM_STRUCT { + struct DT2_EEPROM_MV_CONFIG mv; + struct DT2_EEPROM_SD_CONFIG sd; + struct DT2_EEPROM_FC_CONFIG fc; + struct DT2_EEPROM_GW_CONFIG gw; + unsigned int crc; + } _PACKED_; + +#endif diff --git a/target/linux/orion/files/arch/arm/mach-orion5x/dt2-setup.c b/target/linux/orion/files/arch/arm/mach-orion5x/dt2-setup.c new file mode 100644 index 0000000..f794b4c --- /dev/null +++ b/target/linux/orion/files/arch/arm/mach-orion5x/dt2-setup.c @@ -0,0 +1,445 @@ +/* + * arch/arm/mach-orion5x/dt2-setup.c + * + * Freecom DataTank Gateway Setup + * + * Copyright (C) 2009 Zintis Petersons <Zintis.Petersons@abcsolutions.lv> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/pci.h> +#include <linux/irq.h> +#include <linux/mtd/physmap.h> +#include <linux/mv643xx_eth.h> +#include <linux/ethtool.h> +#include <linux/if_ether.h> +#include <net/dsa.h> +#include <linux/ata_platform.h> +#include <linux/i2c.h> +#include <linux/reboot.h> +#include <linux/interrupt.h> +#include <asm/mach-types.h> +#include <asm/gpio.h> +#include <asm/leds.h> +#include <asm/mach/arch.h> +#include <asm/mach/pci.h> +#include <mach/orion5x.h> +#include "common.h" +#include "mpp.h" + +/***************************************************************************** + * DT2 local + ****************************************************************************/ +#include <asm/setup.h> +#include "dt2-common.h" + +u32 mvUbootVer = 0; +u32 mvTclk = 166666667; +u32 mvSysclk = 200000000; +u32 mvIsUsbHost = 1; +u32 overEthAddr = 0; +u32 gBoardId = -1; +struct DT2_EEPROM_STRUCT dt2_eeprom; + +/***************************************************************************** + * DT2 Info + ****************************************************************************/ +/* + * PCI + */ + +#define DT2_PCI_SLOT0_OFFS 7 +#define DT2_PCI_SLOT0_IRQ_A_PIN 3 +#define DT2_PCI_SLOT0_IRQ_B_PIN 2 + +#define DT2_PIN_GPIO_SYNC 25 +#define DT2_PIN_GPIO_POWER 24 +#define DT2_PIN_GPIO_UNPLUG1 23 +#define DT2_PIN_GPIO_UNPLUG2 22 +#define DT2_PIN_GPIO_RESET 4 + +#define DT2_NOR_BOOT_BASE 0xf4000000 +#define DT2_NOR_BOOT_SIZE SZ_512K + +#define DT2_LEDS_BASE 0xfa000000 +#define DT2_LEDS_SIZE SZ_1K + +/***************************************************************************** + * 512K NOR Flash on Device bus Boot CS + ****************************************************************************/ + +static struct mtd_partition dt2_partitions[] = { + { + .name = "u-boot", + .size = 0x00080000, + .offset = 0, + }, +}; + +static struct physmap_flash_data dt2_nor_flash_data = { + .width = 1, /* 8 bit bus width */ + .parts = dt2_partitions, + .nr_parts = ARRAY_SIZE(dt2_partitions) +}; + +static struct resource dt2_nor_flash_resource = { + .flags = IORESOURCE_MEM, + .start = DT2_NOR_BOOT_BASE, + .end = DT2_NOR_BOOT_BASE + DT2_NOR_BOOT_SIZE - 1, +}; + +static struct platform_device dt2_nor_flash = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &dt2_nor_flash_data, + }, + .resource = &dt2_nor_flash_resource, + .num_resources = 1, +}; + +/***************************************************************************** + * PCI + ****************************************************************************/ + +void __init dt2_pci_preinit(void) +{ + int pin, irq; + + /* + * Configure PCI GPIO IRQ pins + */ + pin = DT2_PCI_SLOT0_IRQ_A_PIN; + if (gpio_request(pin, "PCI IntA") == 0) { + if (gpio_direction_input(pin) == 0) { + irq = gpio_to_irq(pin); + set_irq_type(irq, IRQ_TYPE_LEVEL_LOW); + printk (KERN_INFO "PCI IntA IRQ: %d\n", irq); + } else { + printk(KERN_ERR "dt2_pci_preinit failed to " + "set_irq_type pin %d\n", pin); + gpio_free(pin); + } + } else { + printk(KERN_ERR "dt2_pci_preinit failed to request gpio %d\n", pin); + } + + pin = DT2_PCI_SLOT0_IRQ_B_PIN; + if (gpio_request(pin, "PCI IntB") == 0) { + if (gpio_direction_input(pin) == 0) { + irq = gpio_to_irq(pin); + set_irq_type(irq, IRQ_TYPE_LEVEL_LOW); + printk (KERN_INFO "PCI IntB IRQ: %d\n", irq); + } else { + printk(KERN_ERR "dt2_pci_preinit failed to " + "set_irq_type pin %d\n", pin); + gpio_free(pin); + } + } else { + printk(KERN_ERR "dt2_pci_preinit failed to gpio_request %d\n", pin); + } +} + +static int __init dt2_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +{ + int irq; + + /* + * Check for devices with hard-wired IRQs. + */ + irq = orion5x_pci_map_irq(dev, slot, pin); + if (irq != -1){ + printk(KERN_INFO "orion5x_pci_map_irq: %d\n", irq); + return irq; + } + + /* + * PCI IRQs are connected via GPIOs + */ + switch (slot - DT2_PCI_SLOT0_OFFS) { + case 0: + if (pin == 1){ + irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_A_PIN); + printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_A_PIN: %d\n", irq); + } + else { + irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_B_PIN); + printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_B_PIN: %d\n", irq); + } + default: + irq = -1; + printk(KERN_INFO "dt2_pci_map_irq IRQ: %d\n", irq); + } + + return irq; +} + +static struct hw_pci dt2_pci __initdata = { + .nr_controllers = 2, + .preinit = dt2_pci_preinit, + .swizzle = pci_std_swizzle, + .setup = orion5x_pci_sys_setup, + .scan = orion5x_pci_sys_scan_bus, + .map_irq = dt2_pci_map_irq, +}; + +static int __init dt2_pci_init(void) +{ + if (machine_is_dt2()) + pci_common_init(&dt2_pci); + + return 0; +} + +subsys_initcall(dt2_pci_init); + +/***************************************************************************** + * Ethernet + ****************************************************************************/ + +static struct mv643xx_eth_platform_data dt2_eth_data = { + .phy_addr = MV643XX_ETH_PHY_NONE, + .speed = SPEED_1000, + .duplex = DUPLEX_FULL, +}; + +static struct dsa_platform_data dt2_switch_data = { + .port_names[0] = "wan", + .port_names[1] = "lan1", + .port_names[2] = "lan2", + .port_names[3] = "cpu", + .port_names[4] = "lan3", + .port_names[5] = "lan4", +}; + +/***************************************************************************** + * RTC ISL1208 on I2C bus + ****************************************************************************/ +static struct i2c_board_info __initdata dt2_i2c_rtc = { + I2C_BOARD_INFO("isl1208", 0x6F), +}; + +/***************************************************************************** + * Sata + ****************************************************************************/ +static struct mv_sata_platform_data dt2_sata_data = { + .n_ports = 2, +}; + +/***************************************************************************** + * General Setup + ****************************************************************************/ +static struct orion5x_mpp_mode dt2_mpp_modes[] __initdata = { + { 0, MPP_GPIO }, // RTC interrupt + { 1, MPP_GPIO }, // 88e6131 interrupt + { 2, MPP_GPIO }, // PCI_intB + { 3, MPP_GPIO }, // PCI_intA + { 4, MPP_GPIO }, // reset button switch + { 5, MPP_GPIO }, + { 6, MPP_GPIO }, + { 7, MPP_GPIO }, + { 8, MPP_GPIO }, + { 9, MPP_GIGE }, /* GE_RXERR */ + { 10, MPP_GPIO }, // usb + { 11, MPP_GPIO }, // usb + { 12, MPP_GIGE }, // GE_TXD[4] + { 13, MPP_GIGE }, // GE_TXD[5] + { 14, MPP_GIGE }, // GE_TXD[6] + { 15, MPP_GIGE }, // GE_TXD[7] + { 16, MPP_GIGE }, // GE_RXD[4] + { 17, MPP_GIGE }, // GE_RXD[5] + { 18, MPP_GIGE }, // GE_RXD[6] + { 19, MPP_GIGE }, // GE_RXD[7] + { -1 }, +}; + +/***************************************************************************** + * LEDS + ****************************************************************************/ +static struct platform_device dt2_leds = { + .name = "dt2-led", + .id = -1, +}; + +/**************************************************************************** + * GPIO key + ****************************************************************************/ +static irqreturn_t dt2_reset_handler(int irq, void *dev_id) +{ + /* This is the paper-clip reset which does an emergency reboot. */ + printk(KERN_INFO "Restarting system.\n"); + machine_restart(NULL); + + /* This should never be reached. */ + return IRQ_HANDLED; +} + +static irqreturn_t dt2_power_handler(int irq, void *dev_id) +{ + printk(KERN_INFO "Shutting down system.\n"); + machine_power_off(); + return IRQ_HANDLED; +} + +static void __init dt2_init(void) +{ + DECLARE_MAC_BUF(mac_buf); + /* + * Setup basic Orion functions. Need to be called early. + */ + orion5x_init(); + + orion5x_mpp_conf(dt2_mpp_modes); + + /* + * Configure peripherals. + */ + gpio_display(); + + orion5x_uart0_init(); + orion5x_ehci0_init(); + orion5x_ehci1_init(); + orion5x_i2c_init(); + orion5x_sata_init(&dt2_sata_data); + orion5x_xor_init(); + + printk(KERN_INFO "U-Boot parameters:\n"); + printk(KERN_INFO "Sys Clk = %d, Tclk = %d, BoardID = 0x%02x\n", mvSysclk, mvTclk, gBoardId); + + printk(KERN_INFO "Serial: %s\n", dt2_eeprom.fc.dt2_serial_number); + printk(KERN_INFO "Revision: %016x\n", dt2_eeprom.fc.dt2_revision); + printk(KERN_INFO "DT2: Using MAC address %s for port 0\n", + print_mac(mac_buf, dt2_eeprom.gw.mac_addr[0])); + printk(KERN_INFO "DT2: Using MAC address %s for port 1\n", + print_mac(mac_buf, dt2_eeprom.gw.mac_addr[1])); + + orion5x_eth_init(&dt2_eth_data); + memcpy(dt2_eth_data.mac_addr, dt2_eeprom.gw.mac_addr[0], 6); + orion5x_eth_switch_init(&dt2_switch_data, NO_IRQ); + + i2c_register_board_info(0, &dt2_i2c_rtc, 1); + + orion5x_setup_dev_boot_win(DT2_NOR_BOOT_BASE, DT2_NOR_BOOT_SIZE); + platform_device_register(&dt2_nor_flash); + + orion5x_setup_dev0_win(DT2_LEDS_BASE, DT2_LEDS_SIZE); + platform_device_register(&dt2_leds); + + if (request_irq(gpio_to_irq(DT2_PIN_GPIO_RESET), &dt2_reset_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "DT2: Reset button", NULL) < 0) { + + printk("DT2: Reset Button IRQ %d not available\n", + gpio_to_irq(DT2_PIN_GPIO_RESET)); + } + + if (request_irq(gpio_to_irq(DT2_PIN_GPIO_POWER), &dt2_power_handler, + IRQF_DISABLED | IRQF_TRIGGER_LOW, + "DT2: Power button", NULL) < 0) { + + printk(KERN_DEBUG "DT2: Power Button IRQ %d not available\n", + gpio_to_irq(DT2_PIN_GPIO_POWER)); + } +} + +static int __init parse_tag_dt2_uboot(const struct tag *t) +{ + struct tag_mv_uboot *mv_uboot; + + // Get pointer to our block + mv_uboot = (struct tag_mv_uboot*)&t->u; + mvTclk = mv_uboot->tclk; + mvSysclk = mv_uboot->sysclk; + mvUbootVer = mv_uboot->uboot_version; + mvIsUsbHost = mv_uboot->isUsbHost; + + // Some clock fixups + if(mvTclk == 166000000) mvTclk = 166666667; + else if(mvTclk == 133000000) mvTclk = 133333333; + else if(mvSysclk == 166000000) mvSysclk = 166666667; + + gBoardId = (mvUbootVer & 0xff); + + //DT2 specific data + memcpy(&dt2_eeprom, mv_uboot->dt2_eeprom, sizeof(struct DT2_EEPROM_STRUCT)); + + return 0; +} +__tagtable(ATAG_MV_UBOOT, parse_tag_dt2_uboot); + +/* + * This is OpenWrt specific fixup. It includes code from original "tag_fixup_mem32" to + * fixup bogus memory tags and also fixes kernel cmdline by adding " init=/etc/preinit" + * at the end. It is important to flash OpenWrt image from original Freecom firmware. + * + * Vanilla kernel should use "tag_fixup_mem32" function. + */ +void __init openwrt_fixup(struct machine_desc *mdesc, struct tag *t, + char **from, struct meminfo *meminfo) +{ + char *p = NULL; + static char openwrt_init_tag[] __initdata = " init=/etc/preinit"; + + for (; t->hdr.size; t = tag_next(t)){ + /* Locate the Freecom cmdline */ + if (t->hdr.tag == ATAG_CMDLINE) { + p = t->u.cmdline.cmdline; + printk("%s(%d): Found cmdline '%s' at 0x%0lx\n", + __FUNCTION__, __LINE__, p, (unsigned long)p); + } + /* + * Many orion-based systems have buggy bootloader implementations. + * This is a common fixup for bogus memory tags. + */ + if (t->hdr.tag == ATAG_MEM && + (!t->u.mem.size || t->u.mem.size & ~PAGE_MASK || + t->u.mem.start & ~PAGE_MASK)) { + printk(KERN_WARNING + "Clearing invalid memory bank %dKB@0x%08x\n", + t->u.mem.size / 1024, t->u.mem.start); + t->hdr.tag = 0; + } + } + + printk("%s(%d): End of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t); + + /* Overwrite the end of the table with a new cmdline tag. */ + t->hdr.tag = ATAG_CMDLINE; + t->hdr.size = + (sizeof (struct tag_header) + + strlen(p) + strlen(openwrt_init_tag) + 1 + 4) >> 2; + + strlcpy(t->u.cmdline.cmdline, p, COMMAND_LINE_SIZE); + strlcpy(t->u.cmdline.cmdline + strlen(p), openwrt_init_tag, + COMMAND_LINE_SIZE - strlen(p)); + + printk("%s(%d): New cmdline '%s' at 0x%0lx\n", + __FUNCTION__, __LINE__, + t->u.cmdline.cmdline, (unsigned long)t->u.cmdline.cmdline); + + t = tag_next(t); + + printk("%s(%d): New end of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t); + + t->hdr.tag = ATAG_NONE; + t->hdr.size = 0; +} + +/* Warning: Freecom uses their own custom bootloader with mach-type (=1500) */ +MACHINE_START(DT2, "Freecom DataTank Gateway") + /* Maintainer: Zintis Petersons <Zintis.Petersons@abcsolutions.lv> */ + .phys_io = ORION5X_REGS_PHYS_BASE, + .io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .init_machine = dt2_init, + .map_io = orion5x_map_io, + .init_irq = orion5x_init_irq, + .timer = &orion5x_timer, + .fixup = openwrt_fixup, //tag_fixup_mem32, +MACHINE_END diff --git a/target/linux/orion/image/Makefile b/target/linux/orion/image/Makefile index 0ca3767..66edc04 100644 --- a/target/linux/orion/image/Makefile +++ b/target/linux/orion/image/Makefile @@ -26,6 +26,13 @@ define Image/BuildKernel -C none -a 0x00008000 -e 0x00008000 -n 'Linux-$(LINUX_VERSION)' \ -d $(KDIR)/wnr854t-zImage $(KDIR)/wnr854t-uImage cp $(KDIR)/wnr854t-uImage $(BIN_DIR)/openwrt-wnr854t-uImage +# DT2: mach id 1514 (0x5EA) + echo -en "\x05\x1c\xa0\xe3\xea\x10\x81\xe3" > $(KDIR)/dt2-zImage + cat $(LINUX_DIR)/arch/arm/boot/zImage >> $(KDIR)/dt2-zImage + $(STAGING_DIR_HOST)/bin/mkimage -A arm -O linux -T kernel \ + -C none -a 0x00008000 -e 0x00008000 -n 'Linux-$(LINUX_VERSION)' \ + -d $(KDIR)/dt2-zImage $(KDIR)/dt2-uImage + cp $(KDIR)/dt2-uImage $(BIN_DIR)/openwrt-dt2-uImage endef define Image/Build/Netgear @@ -44,10 +51,21 @@ define Image/Build/Linksys # placeholder for the WRT350N v2 endef +define Image/Build/Freecom + $(INSTALL_DIR) $(TARGET_DIR)/boot + # TODO: Add special CMDLINE shim for webupgrade image here + $(CP) $(KDIR)/dt2-uImage $(TARGET_DIR)/boot/uImage + rm -rf $(TARGET_DIR)/{var,jffs,rom} + $(INSTALL_DIR) $(TARGET_DIR)/var + $(TAR) cfj $(BIN_DIR)/openwrt-$(2)-$(1).img --owner=root --group=root -C $(TARGET_DIR)/ . + $(STAGING_DIR_HOST)/bin/encode_crc $(BIN_DIR)/openwrt-$(2)-$(1).img $(BIN_DIR)/openwrt-$(2)-$(1)-webupgrade.img $(3) +endef + define Image/Build $(call Image/Build/$(1),$(1)) $(call Image/Build/Netgear,$(1),wnr854t,NG_WNR854T,$(1)) $(call Image/Build/Linksys,$(1),wrt350nv2,WNR350Nv2,$(1)) + $(call Image/Build/Freecom,$(1),dt2,DT,$(1)) endef define Image/Build/squashfs diff --git a/target/linux/orion/patches/200-dt2_board_support.patch b/target/linux/orion/patches/200-dt2_board_support.patch new file mode 100644 index 0000000..bf82ed7 --- /dev/null +++ b/target/linux/orion/patches/200-dt2_board_support.patch @@ -0,0 +1,26 @@ +diff -ruN linux-2.6.28.5.orig/arch/arm/mach-orion5x/Kconfig linux-2.6.28.5/arch/arm/mach-orion5x/Kconfig +--- linux-2.6.28.5.orig/arch/arm/mach-orion5x/Kconfig 2009-02-21 00:41:27.000000000 +0200 ++++ linux-2.6.28.5/arch/arm/mach-orion5x/Kconfig 2009-02-28 10:06:24.000000000 +0200 +@@ -16,6 +16,13 @@ + Say 'Y' here if you want your kernel to support the + Marvell Orion-NAS (88F5182) RD2 + ++config MACH_DT2 ++ bool "Freecom DataTank Gateway" ++ select I2C_BOARDINFO ++ help ++ Say 'Y' here if you want your kernel to support the ++ Freecom DataTank Gateway ++ + config MACH_KUROBOX_PRO + bool "KuroBox Pro" + select I2C_BOARDINFO +diff -ruN linux-2.6.28.5.orig/arch/arm/mach-orion5x/Makefile linux-2.6.28.5/arch/arm/mach-orion5x/Makefile +--- linux-2.6.28.5.orig/arch/arm/mach-orion5x/Makefile 2009-02-21 00:41:27.000000000 +0200 ++++ linux-2.6.28.5/arch/arm/mach-orion5x/Makefile 2009-02-28 10:07:35.000000000 +0200 +@@ -17,3 +17,4 @@ + obj-$(CONFIG_MACH_RD88F5181L_GE) += rd88f5181l-ge-setup.o + obj-$(CONFIG_MACH_RD88F5181L_FXO) += rd88f5181l-fxo-setup.o + obj-$(CONFIG_MACH_RD88F6183AP_GE) += rd88f6183ap-ge-setup.o ++obj-$(CONFIG_MACH_DT2) += dt2-setup.o + |