summaryrefslogtreecommitdiff
path: root/target
diff options
context:
space:
mode:
Diffstat (limited to 'target')
-rw-r--r--target/linux/adm5120/files/drivers/i2c/busses/i2c-gpio-custom.c169
-rw-r--r--target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch33
-rw-r--r--target/linux/adm5120/router_be/config-2.6.2211
-rw-r--r--target/linux/adm5120/router_le/config-2.6.2211
4 files changed, 151 insertions, 73 deletions
diff --git a/target/linux/adm5120/files/drivers/i2c/busses/i2c-gpio-custom.c b/target/linux/adm5120/files/drivers/i2c/busses/i2c-gpio-custom.c
index a019faf..9d62a2d 100644
--- a/target/linux/adm5120/files/drivers/i2c/busses/i2c-gpio-custom.c
+++ b/target/linux/adm5120/files/drivers/i2c/busses/i2c-gpio-custom.c
@@ -6,6 +6,40 @@
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
+ *
+ * ---------------------------------------------------------------------------
+ *
+ * The behaviour of this driver can be altered by setting some parameters
+ * from the insmod command line.
+ *
+ * The following parameters are adjustable:
+ *
+ * bus0 These four arguments can be arrays of
+ * bus1 1-8 unsigned integers as follows:
+ * bus2
+ * bus3 <id>,<sda>,<scl>,<udelay>,<timeout>,<sda_od>,<scl_od>,<scl_oo>
+ *
+ * where:
+ *
+ * <id> ID to used as device_id for the corresponding bus (required)
+ * <sda> GPIO pin ID to used for SDA (required)
+ * <scl> GPIO pin ID to used for SCL (required)
+ * <udelay> signal toggle delay.
+ * <timeout> clock stretching timeout.
+ * <sda_od> SDA is configured as open drain.
+ * <scl_od> SCL is configured as open drain.
+ * <scl_oo> SCL output drivers cannot be turned off.
+ *
+ * See include/i2c-gpio.h for more information about the parameters.
+ *
+ * If this driver is built into the kernel, you can use the following kernel
+ * command line parameters, with the same values as the corresponding module
+ * parameters listed above:
+ *
+ * i2c-gpio-custom.bus0
+ * i2c-gpio-custom.bus1
+ * i2c-gpio-custom.bus2
+ * i2c-gpio-custom.bus3
*/
#include <linux/kernel.h>
@@ -16,56 +50,141 @@
#include <linux/i2c-gpio.h>
#define DRV_NAME "i2c-gpio-custom"
-#define DRV_DESC "Custom GPIO I2C device driver"
+#define DRV_DESC "Custom GPIO-based I2C driver"
+#define DRV_VERSION "0.1.0"
+
+#define PFX DRV_NAME ": "
+
+#define BUS_PARAM_ID 0
+#define BUS_PARAM_SDA 1
+#define BUS_PARAM_SCL 2
+#define BUS_PARAM_UDELAY 3
+#define BUS_PARAM_TIMEOUT 4
+#define BUS_PARAM_SDA_OD 5
+#define BUS_PARAM_SCL_OD 6
+#define BUS_PARAM_SCL_OO 7
+
+#define BUS_PARAM_REQUIRED 3
+#define BUS_PARAM_COUNT 8
+#define BUS_COUNT_MAX 4
+
+static unsigned int bus0[BUS_PARAM_COUNT] __initdata;
+static unsigned int bus1[BUS_PARAM_COUNT] __initdata;
+static unsigned int bus2[BUS_PARAM_COUNT] __initdata;
+static unsigned int bus3[BUS_PARAM_COUNT] __initdata;
+
+static unsigned int bus_nump[BUS_COUNT_MAX] __initdata;
+
+#define BUS_PARM_DESC \
+ " config -> id,sda,scl[,udelay,timeout,sda_od,scl_od,scl_oo]"
+
+module_param_array(bus0, uint, &bus_nump[0], 0);
+MODULE_PARM_DESC(bus0, "bus0" BUS_PARM_DESC);
+module_param_array(bus1, uint, &bus_nump[1], 0);
+MODULE_PARM_DESC(bus1, "bus1" BUS_PARM_DESC);
+module_param_array(bus2, uint, &bus_nump[2], 0);
+MODULE_PARM_DESC(bus2, "bus2" BUS_PARM_DESC);
+module_param_array(bus3, uint, &bus_nump[3], 0);
+MODULE_PARM_DESC(bus3, "bus3" BUS_PARM_DESC);
+
+static struct platform_device *devices[BUS_COUNT_MAX];
+static unsigned int nr_devices;
+
+static void i2c_gpio_custom_cleanup(void)
+{
+ int i;
-static unsigned int sda = CONFIG_I2C_GPIO_CUSTOM_SDA;
-static unsigned int scl = CONFIG_I2C_GPIO_CUSTOM_SCL;
-static int id = CONFIG_I2C_GPIO_CUSTOM_DEVICE_ID;
+ for (i = 0; i < nr_devices; i++)
+ if (devices[i])
+ platform_device_unregister(devices[i]);
+}
-module_param(sda, uint, S_IRUGO);
-MODULE_PARM_DESC(sda, "GPIO pin for SDA");
+static int __init i2c_gpio_custom_add_one(unsigned int id, unsigned int *params)
+{
+ struct platform_device *pdev;
+ struct i2c_gpio_platform_data pdata;
+ int err;
-module_param(scl, uint, S_IRUGO);
-MODULE_PARM_DESC(scl, "GPIO pin for SCL");
+ if (!bus_nump[id])
+ return 0;
-module_param(id, int, S_IRUGO);
-MODULE_PARM_DESC(id, "device id of the i2c-gpio device");
+ if (bus_nump[id] < BUS_PARAM_REQUIRED) {
+ printk(KERN_ERR PFX "not enough parameters for bus%d\n", id);
+ err = -EINVAL;
+ goto err;
+ }
-static struct i2c_gpio_platform_data i2c_data;
-static struct platform_device i2c_device;
+ pdev = platform_device_alloc("i2c-gpio", params[BUS_PARAM_ID]);
+ if (!pdev) {
+ err = -ENOMEM;
+ goto err;
+ }
-static void i2c_gpio_custom_release(struct platform_device *pdev)
-{
- /* nothing to do */
+ devices[nr_devices++] = pdev;
+
+ pdata.sda_pin = params[BUS_PARAM_SDA];
+ pdata.scl_pin = params[BUS_PARAM_SCL];
+ pdata.udelay = params[BUS_PARAM_UDELAY];
+ pdata.timeout = params[BUS_PARAM_TIMEOUT];
+ pdata.sda_is_open_drain = params[BUS_PARAM_SDA_OD] != 0;
+ pdata.scl_is_open_drain = params[BUS_PARAM_SCL_OD] != 0;
+ pdata.scl_is_output_only = params[BUS_PARAM_SCL_OO] != 0;
+
+ err = platform_device_add_data(pdev, &pdata, sizeof(pdata));
+ if (err)
+ goto err;
+
+ err = platform_device_register(pdev);
+ if (err)
+ goto err;
+
+ return 0;
+
+err:
+ return err;
}
static int __init i2c_gpio_custom_init(void)
{
int err;
- i2c_data.sda_pin = sda;
- i2c_data.scl_pin = scl;
+ printk(KERN_INFO DRV_DESC " version " DRV_VERSION "\n");
+
+ err = i2c_gpio_custom_add_one(0, bus0);
+ if (err) goto err;
- i2c_device.name = "i2c-gpio";
- i2c_device.id = id;
+ err = i2c_gpio_custom_add_one(1, bus1);
+ if (err) goto err;
- i2c_device.dev.platform_data = &i2c_data,
- i2c_device.dev.release = i2c_gpio_custom_release,
+ err = i2c_gpio_custom_add_one(2, bus2);
+ if (err) goto err;
- err = platform_device_register(&i2c_device);
+ err = i2c_gpio_custom_add_one(3, bus3);
+ if (err) goto err;
+ if (!nr_devices) {
+ printk(KERN_ERR PFX "no bus parameter(s) specified\n");
+ err = -ENODEV;
+ goto err;
+ }
+
+ return 0;
+
+err:
+ i2c_gpio_custom_cleanup();
return err;
}
+module_init(i2c_gpio_custom_init);
static void __exit i2c_gpio_custom_exit(void)
{
- platform_device_unregister(&i2c_device);
+ i2c_gpio_custom_cleanup();
}
-
-module_init(i2c_gpio_custom_init);
module_exit(i2c_gpio_custom_exit);
+
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Gabor Juhos <juhosg at openwrt.org >");
MODULE_DESCRIPTION(DRV_DESC);
+MODULE_VERSION(DRV_VERSION);
diff --git a/target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch b/target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch
index 2bbb197..8c08b74 100644
--- a/target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch
+++ b/target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch
@@ -1,42 +1,19 @@
--- linux-2.6.22.4.orig/drivers/i2c/busses/Kconfig 2007-08-21 06:33:06.000000000 +0200
+++ linux-2.6.22.4/drivers/i2c/busses/Kconfig 2007-10-09 12:53:13.000000000 +0200
-@@ -125,6 +125,40 @@
+@@ -125,6 +125,17 @@
This is a very simple bitbanging I2C driver utilizing the
arch-neutral GPIO API to control the SCL and SDA lines.
+config I2C_GPIO_CUSTOM
-+ tristate "Custom GPIO-based I2C device"
++ tristate "Custom GPIO-based I2C driver"
+ depends on GENERIC_GPIO
+ select I2C_GPIO
+ help
-+ This is an I2C driver to register a custom i2c-gpio device.
++ This is an I2C driver to register 1 to 4 custom I2C buses using
++ GPIO lines.
+
+ This support is also available as a module. If so, the module
-+ will be called i2c-gpio-dev.
-+
-+config I2C_GPIO_CUSTOM_SDA
-+ int "Custom GPIO pin for SDA"
-+ depends on I2C_GPIO_CUSTOM
-+ default "0"
-+ help
-+ Enter the GPIO pin number used for the SDA signal. This value can
-+ also be specified with a module parameter.
-+
-+config I2C_GPIO_CUSTOM_SCL
-+ int "Custom GPIO pin for SCL"
-+ depends on I2C_GPIO_CUSTOM
-+ default "1"
-+ help
-+ Enter the GPIO pin number used for the SCL signal. This value can
-+ also be specified with a module parameter.
-+
-+config I2C_GPIO_CUSTOM_DEVICE_ID
-+ int "Custom GPIO device id"
-+ depends on I2C_GPIO_CUSTOM
-+ default "0"
-+ help
-+ Enter the number used for the device id of the custom i2c-gpio device.
-+ This value can also be specified with a module parameter.
++ will be called i2c-gpio-custom.
+
config I2C_HYDRA
tristate "CHRP Apple Hydra Mac I/O I2C interface"
diff --git a/target/linux/adm5120/router_be/config-2.6.22 b/target/linux/adm5120/router_be/config-2.6.22
index bb52446..0fca8f8 100644
--- a/target/linux/adm5120/router_be/config-2.6.22
+++ b/target/linux/adm5120/router_be/config-2.6.22
@@ -73,15 +73,7 @@ CONFIG_HW_RANDOM=y
CONFIG_HZ=250
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
-CONFIG_I2C=m
-CONFIG_I2C_ALGOBIT=m
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=m
-CONFIG_I2C_GPIO=m
-CONFIG_I2C_GPIO_CUSTOM=m
-CONFIG_I2C_GPIO_CUSTOM_DEVICE_ID=0
-CONFIG_I2C_GPIO_CUSTOM_SCL=1
-CONFIG_I2C_GPIO_CUSTOM_SDA=0
+# CONFIG_I2C is not set
# CONFIG_IDE is not set
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
CONFIG_INITRAMFS_SOURCE=""
@@ -196,7 +188,6 @@ CONFIG_PCI_ADM5120=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_SCSI_WAIT_SCAN=m
-# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SERIAL_8250 is not set
# CONFIG_SERIAL_ADM5120 is not set
CONFIG_SERIAL_AMBA_PL010=y
diff --git a/target/linux/adm5120/router_le/config-2.6.22 b/target/linux/adm5120/router_le/config-2.6.22
index 579e2cf..a876583 100644
--- a/target/linux/adm5120/router_le/config-2.6.22
+++ b/target/linux/adm5120/router_le/config-2.6.22
@@ -73,15 +73,7 @@ CONFIG_HW_RANDOM=y
CONFIG_HZ=250
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
-CONFIG_I2C=m
-CONFIG_I2C_ALGOBIT=m
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=m
-CONFIG_I2C_GPIO=m
-CONFIG_I2C_GPIO_CUSTOM=m
-CONFIG_I2C_GPIO_CUSTOM_DEVICE_ID=0
-CONFIG_I2C_GPIO_CUSTOM_SCL=1
-CONFIG_I2C_GPIO_CUSTOM_SDA=0
+# CONFIG_I2C is not set
# CONFIG_IDE is not set
CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
CONFIG_INITRAMFS_SOURCE=""
@@ -206,7 +198,6 @@ CONFIG_PCI_ADM5120=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_SCSI_WAIT_SCAN=m
-# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SERIAL_8250 is not set
# CONFIG_SERIAL_ADM5120 is not set
CONFIG_SERIAL_AMBA_PL010=y