summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for I-O DATA WN-GX300GRINAGAKI Hiroshi2018-06-196-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek MT7621S. Specification: - MT7621S (1-Core, 2-Threads) - 64 MB of RAM - 8 MB of Flash (SPI) - 2T2R 2.4 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR" and place it in the TFTP directory 3. Set the IP address of the computer to 192.168.99.8, connect to the LAN port of WN-GX300GR, and start the TFTP server on the computer 4. Connect power cable to WN-GX300GR and turn on the router 5. Press "1" key on the serial console to interrupt boot process on U-Boot, press Enter key 3 times and start firmware download via TFTP 6. WN-GX300GR downloads initramfs image and boot with it 7. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-GX300GR 8. Wait ~150 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-199-7/+484
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7621: fix wireless package selectionMathias Kresin2018-06-191-5/+4
| | | | | | | Add wpad-mini if wireless drivers are included. Drop the mt76 package if both of the provided drivers are included with their own packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ds-lite: make tunnel encapsulation limit support configurable (FS#1501)Hans Dedecker2018-06-192-3/+7
| | | | | | | | | | | | Be compatible with ISPs which don't support the destination option header containing the tunnel encapsulation limit as reported in FS#1501. Setting the uci parameter encaplimit to ignore; allows to disable the insertion of the destination option header in the ds-lite packets. Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255 by setting the encaplimit uci parameter accordingly. If no encaplimit value is specified the default value is 4 as before. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* odhcp6c: make ds-lite/map tunnel encapsulation limit support configurable ↵Hans Dedecker2018-06-193-3/+9
| | | | | | | | | | | | | | (FS#1501) Be compatible with ISPs which don't support the destination option header containing the tunnel encapsulation limit as reported in FS#1501 for dynamic created ds-lite/map interfaces. Setting the uci parameter encaplimit_dslite/map to ignore; allows to disable the insertion of the destination option header for the dynamic created ds-lite/map interface. Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255 by setting the encaplimit_dslite/map uci parameter accordingly. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* netifd: update to latest git HEAD (FS#1501)Hans Dedecker2018-06-191-3/+3
| | | | | | a580028 system-linux: make encaplimit configurable for ip6 tunnels (FS#1501) Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* map: make tunnel encapsulation limit support configurable (FS#1501)Hans Dedecker2018-06-192-8/+10
| | | | | | | | | | | | Be compatible with ISPs which don't support the destination option header containing the tunnel encapsulation limit as reported in FS#1501. Setting the uci parameter encaplimit to ignore; allows to disable the insertion of the destination option header in the map-e packets. Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255 by setting the encaplimit uci parameter accordingly. If no encaplimit value is specified the default value is 4 as before. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* mvebu: reduce speed to gen1 for espressobin pcieTomasz Maciej Nowak2018-06-192-0/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the beginning there's been an issue with initializing the Atheros based MiniPCIe wireless cards. Here's an example of kerenel log: OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit] pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref] [...] advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k 0000:00:00.0: enabling device (0000 -> 0002) advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40 ath9k 0000:00:00.0: request_irq failed advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k: probe of 0000:00:00.0 failed with error -22 The same happens for ath5k cards, while ath10k card didn't appear at all (not detected): OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link never came up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) advk-pcie d0070000.pcie: config read/write timed out Following the issue on esppressobin.net forum [1] the workaround seems to be limiting the speed of PCIe bridge to 1st generation. This fixed the initialisation of all tested Atheros wireless cards. The change shouldn't affect the performance for wireless cards, it could reduce the performance of storage controller cards but since OpenWrt focuses on wireless connectivity, fixing compatibility with wireless cards should be a priority. For the record, the iwlwifi and mt76 cards were not affected by this issue. 1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit 772258044b48036699302840abf96cd34c4e5078)
* mvebu: add fix for armada 37xx cpufreq driverTomasz Maciej Nowak2018-06-191-0/+35
| | | | | | | Backport from stable kernel tree fixing clock leak. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit 4ec8c8c23ed50dbe9cabbfc544ae2780f0287fd0)
* kernel: add missing softdog symbolJohn Crispin2018-06-191-1/+2
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 9c409cb4e2670edddd8de5e8536ea295d44b9e16)
* build: add busybox support to `time` prereq-checkAndy Boyett2018-06-182-3/+4
| | | | | | | | | | | | | | | Busybox time supports the GNU time '-f' syntax used by the build time logging implemented in ff6e62b288c, however the prerequisite check added only works with GNU time installed as `time` or `gtime`. As busybox is a multicall binary, the name of the symlink setup by SetupHostCommand also must be changed from `gtime` to `time` to fix the value of argv[0]. This causes a number of shells (including bash) to use their builtin impelementation of time, so the sole invocation has been changed to use `env time` to use the value found on the $PATH. Signed-off-by: Andy Boyett <agb@agb.io> (cherry picked from commit 591780615b304fb4624e363135942e9ee8f6caa3)
* build: use busybox gzip compatible force optionMathew McBride2018-06-181-1/+1
| | | | | | | | | | | commit 138c763 ("build: add --force option to gzip in Build/gzip") added the --force flag to the gzip invocation. Under environments with busybox gzip (e.g Alpine Linux), this fails as busybox only recognizes "-f". Signed-off-by: Mathew McBride <matt@traverse.com.au> (cherry picked from commit fba168f5745acac95db519a9984b62e3e508df6a)
* kernel: atm: pppoatm fix vc-mux connection failuresKevin Darbyshire-Bryant2018-06-181-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport a hot off the press upstream kernel ATM fix: Preserve value of skb->truesize when accounting to vcc "There's a hack in pskb_expand_head() to avoid adjusting skb->truesize for certain skbs. Ideally it would cover ATM too. It doesn't. Just stashing the accounted value and using it in atm_raw_pop() is probably the easiest way to cope." The issue was exposed by upstream with: commit 14afee4b6092fde451ee17604e5f5c89da33e71e Author: Reshetova, Elena <elena.reshetova@intel.com> Date: Fri Jun 30 13:08:00 2017 +0300 net: convert sock.sk_wmem_alloc from atomic_t to refcount_t But an earlier commit left the ticking timebomb: 158f323b9868 ("net: adjust skb->truesize in pskb_expand_head() Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging assistance and to David Woodhouse <dwmw2@infradead.org> for further guidance, cajoling & patience in interpreting the debug I was giving him and producing a fix! Fixes FS#1567 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> (cherry picked from commit d600de3ddde269bf0b324735f8f12278f82d9b37)
* include/image-commands.mk: shorter version in Netgear factory headerHannu Nyman2018-06-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Shorten the version string in Netgear factory image header in order to enable u-boot TFTP recovery flash mode to work again. Strip 'r7210-14cb05909a' into 'r7210' in the Netgear image header by removing the hash (anything after "-"). background: Some Netgear routers have recently been unable to flash Openwrt factory image with the TFTP recovery flash mode provided by Netgear u-boot. That is due to over-long Openwrt version string overflowing into the router type string in u-boot code. Modern git versions produce 10-digit short hashes for the Openwrt main repo, and that causes the version string to be too long in the image header, breaking the image ID verification by the TFTP flash routine. (Other option could be to force a shorter hash in scripts/getver.sh, but as the problem only concerns Netgear routers, let's patch just them.) More detailed explanations in FS#1583 Tested with WNDR3800 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> (cherry picked from commit dcfe2a461e4b06de6e2b23d29afebbb3c775f647)
* mips: fix dynamic ftraceVincent Wiemann2018-06-181-3/+8
| | | | | | | | | | | The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as dynamic ftrace depends on -mlong-calls. See http://patchwork.linux-mips.org/patch/675/ Thus we always set -mlong-calls if the kernel is being compiled with dynamic ftrace support. Signed-off-by: Vincent Wiemann <webmaster@codefetch.de> (cherry picked from commit 076d2ea6829855ee14ebd65230146eb27ee16750)
* ar71xx: add kmod-usb-ehci to fix USB on RB hAP ACThomas Nixon2018-06-181-1/+1
| | | | | Signed-off-by: Thomas Nixon <tom@tomn.co.uk> (cherry picked from commit bb71a3f27efb4140c47e98b933bdb64384cbcbbf)
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> (cherry picked from commit 8f804f42d52e49191429ad1d716e7adb3cd10ceb)
* ipq806x: D7800 only has a single sata portJohn Crispin2018-06-181-0/+1
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit ee1dbffeed442b4968af48b2492ad41ac988dab8)
* mvebu: backport ahci_mvebu errata patchsetJeremiah McConnell2018-06-182-0/+334
| | | | | | | | | | | | | Marvell ahci hardware requires a workaround to prevent eSATA failures on hotplug/reset when used with multi-bay external enclosures. Errata Ref#226 - SATA Disk HOT swap issue when connected through Port Multiplier in FIS-based Switching mode. These patches backport the workaround from 4.17. Signed-off-by: Jeremiah McConnell <miah@miah.com> (cherry picked from commit e820455198aa50cc32f9a108a4696f0cc23023c3)
* cron: add procd listeners for crontabsPaul Spooren2018-06-181-3/+5
| | | | | | | | | Add procd file listeners to check files in `/etc/crontabs/`. Also unified a bit the function style. Signed-off-by: Paul Spooren <mail@aparcar.org> (cherry picked from commit cbf69fb2adced6096addbe6aeb54c1971c63dbe4)
* mediatek: mt7622: Do not deactivate CONFIG_BLK_DEVHauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | zram.ko needs CONFIG_BLK_DEV activated and it is by default for all other targets in OpenWrt. This makes zram.ko compile again. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 6745af9a0de28171b45c0e8584e393bd80f0a377)
* mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53Hauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | | | Neon and vfpv4 are mandatory extensions in the ARM64 instruction set now, do not activate them explicitly. GCC will make use of these extension now by default. This makes it possible to share the toolchain with other Cortex A53 SoCs. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 10ce015c652b1e48c1c113604e26481626fa6059)
* mvebu: enable SATA port multiplier supportJeremiah McConnell2018-06-181-0/+1
| | | | | | | | | | | Some of the Marvell targets have functional SATA port multiplier support, which is required for multi-bay eSATA enclosures. Enable kernel support by setting CONFIG_SATA_PMP. Closes: FS#1232 and FS#547 Signed-off-by: Jeremiah McConnell <miah@miah.com> (cherry picked from commit 390c4df2c0b2e7b31c52eca3dcba139b0d745a97)
* ltq-vdsl-mei: reset g_tx_link_rate on showtime exitMartin Schiller2018-06-181-0/+12
| | | | | | | | | | | | | Without this change, ifx_mei_atm_showtime_check() will always return "showtime" after one call of MEI_InternalXtmSwhowtimeEntrySignal() was done, even if MEI_InternalXtmSwhowtimeExitSignal() was called in the meantime. The ifx_mei_atm_showtime_check() function is used by the ltq-atm and ltq-ptm driver. Signed-off-by: Martin Schiller <ms@dev.tdt.de> (cherry picked from commit eee8ab59dc8bc4c599b3508201349fdd96463e69)
* ar71xx: Fix offset to WMAC address for 8devices LimaSven Eckelmann2018-06-181-3/+1
| | | | | | | | | | | | | | | | | | | The ART partition of the Lima board stores exactly three mac addresses: * 0x0: eth0 * 0x6: eth1 * 0x1002: wmac The first two are correctly assigned in the mach file but the latter points to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when it doesn't find a valid mac address in the platform_data. Remove this bogus offset to the ART partition to directly load the wmac via the EEPROM data in the ART partition. Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 4f6320704f7e37368a1dae2deba767a73b3bf121)
* ipq806x: Limit NR_CPUS to 2Rosen Penev2018-06-181-1/+1
| | | | | | | | | | | ipq806x is all dual core processors. ipq807x is quad core. Removes this from dmesg: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit fff65dbe2436351ea1feee6c79110971ec4d5881)
* mtd: mark as nonshared to fix FS#484Mirko Parthey2018-06-181-0/+2
| | | | | | | | | | | The mtd tool is built with different configurations depending on the target. For example, brcm47xx adds the fixtrx subcommand, without which an image fails when booting the second time. Mark the mtd package as nonshared to really fix FS#484. Signed-off-by: Mirko Parthey <mirko.parthey@web.de> (cherry picked from commit 46d7ced9d1e104693a9f995bfe8a6e28ac82b592)
* mediatek: add missing symbols for mt7622John Crispin2018-06-181-1/+1
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 55f37310020c48ff575158791eb8dbcc6802c549)
* mediatek: add missing symbolsJohn Crispin2018-06-182-8/+8
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit de6162e832d028d24267d9cbfc64c71b9a7c5ec9)
* mediatek: add mt7622 subtargetJohn Crispin2018-06-187-1/+565
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 51740777fb37cb7bdc250d74b366840269439cf3)
* mediatek: backport upstream mediatek patchesJohn Crispin2018-06-18130-99/+21978
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 050da2107a7eb2a571a8a3d0cee21cc6a44b72b8)
* uboot-oxnas: fix typo accidentally committed during oxnas rebootDaniel Golle2018-06-181-1/+1
| | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry-picked from ff0f3522b7)
* uboot-oxnas: fix build with newer GCCDaniel Golle2018-06-182-0/+593
| | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry-picked from d44b7b7d31)
* oxnas: reboot targetDaniel Golle2018-06-1873-10633/+1899
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reboot the oxnas target based on Linux 4.14 by rebasing our support on top of the now-existing upstream kernel support. This commit brings oxnas support to the level of v4.17 having upstream drivers for Ethernet, Serial and NAND flash. Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the new platform code and device-tree. Re-introduce base-files from old oxnas target which works for now but needs further clean-up towards generic board support. Functional issues: * PCIe won't come up (hence no USB3 on Shuttle KD20) * I2C bus of Akitio myCloud device is likely not to work (missing debounce support in new pinctrl driver) Code-style issues: * plla/pllb needs further cleanup -- currently their users are writing into the syscon regmap after acquireling the clk instead of using defined clk_*_*() functions to setup multipliers and dividors. * PCIe phy needs its own little driver. * SATA driver is a monster and should be split into an mfd having a raidctrl regmap, sata controller, sata ports and sata phy. Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (squash-picked commit 17511a7ea8 and commit dcc34574ef from master)
* kernel: bump 4.14 to 4.14.50 for 18.06Koen Vandeputte2018-06-181-2/+2
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.109 for 18.06Koen Vandeputte2018-06-183-6/+6
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.49 for 18.06Koen Vandeputte2018-06-184-11/+11
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86-64 Runtime-tested on: cns3xxx, imx6, x86-64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.108 for 18.06Koen Vandeputte2018-06-189-173/+195
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add support for TP-Link TL-WR842N v5Maxim Anisimov2018-06-166-1/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 7x LED, 2x button, power input switch Flash instruction: The only way to flash OpenWrt image in wr842nv5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: use phytpt trigger for mt76 wirelessDavid Bauer2018-06-161-4/+4
| | | | | | | | | | | | | With this change, the LED trigger is independent from the (wireless) netdev name. The (wireless) netdev name can be easiliy changed in OpenWrt and would require an update of the netdev trigger settings each time it is done. This change is (for now) applied only to MT7628 devices from TP-Link, as we only had the possibility to test this change against two of those devices, namely a TL-WR841 v13 and a Archer C50 v3. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix mt7688 watchdog register base addrlbzhung2018-06-161-2/+2
| | | | | | | | | | | | | I found mt7688 watchdog not working. The watchdog registers are identical for mt7621 and mt7628/mt7688. The first watchdog related register is at 0x10000100, the last one - a 16bit sized - at 0x10000128. Set the correct register address and size in the dtsi file to get the watchdog working. Signed-off-by: lbzhung <gewalalb@gmail.com> [add commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* mt76: update to the latest versionFelix Fietkau2018-06-151-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | 73edb22 mt76: discard early received packets if not running yet 0b8d1dd mt76: fix beacon timer drift 20c0766 mt7603: adjust rx hang watchdog for MT7628 664e321 mt7603: add extra PSE hang check signature for MT7628 f24b56f update MT7628 firmware to the latest version d87e4b0 mt7603: clear PSE reset bit if PSE reset fails 0ef26ef mt76: only stop tx queues on offchannel, not during the entire scan f399da3 mt76: prevent tx scheduling during channel change 21c1e1e mt76: move ieee80211_hw allocation to common core 730c292 mt76: wait for pending tx to complete before switching channel fcbb49e mt76x2: use udelay instead of usleep_range in mt76x2_mac_stop 792dbe0 mt7603: do not hold dev->mutex while flushing dev->mac_work 9090f9c mt76x2: fix threshold for gain adjustment 2cbaa57 mt76x2: fix swapped values for RXO-18 in gain control a39ab70 mt76x2: adjust AGC control register 26 based on gain for VHT80 4936c0c mt76x2: clear false CCA counters after changing gain settings 1528fe7 mt76x2: fix variable gain adjustment range f3522e1 mt76x2: add a debugfs file to dump agc calibration information 65e161b mt76x2: fix tracking rssi for dynamic gain adjustment Signed-off-by: Felix Fietkau <nbd@nbd.name>
* libnfnetlink: Remove dead mirrorDaniel Engberg2018-06-141-2/+1
| | | | | | Remove mirrors.evolva.ro as it's no longer available Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* kernel: fix conntrack fixup of offloaded flows on timeoutFelix Fietkau2018-06-143-9/+33
| | | | | | Fixes excessively long conntrack timeout of short lived connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix conntrack leak for flow_offload connectionsFelix Fietkau2018-06-143-28/+123
| | | | | | | This was caused by a race condition between offload teardown and conntrack gc bumping the timeout of offloaded connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: allow hardware NAT offload drivers to keep a priv pointerFelix Fietkau2018-06-141-0/+25
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* dnsmasq: fix confdir option processing (FS#1572)Hans Dedecker2018-06-112-2/+3
| | | | | | | | Fix condir option processing allowing to use the format "<directory>[,<file-extension>......]," as documented on the dnsmasq man page which previously resulted into bogus dir being created. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* base-files: sysupgrade: fix handling get_image unpack commandsMatthias Schiffer2018-06-111-6/+6
| | | | | | | | On bcm53xx and brcm47xx, commands are passed to default_do_upgrade that expect the image to be passed on stdin, rather than as an argument. Fixes: 30f61a34b4cf ("base-files: always use staged sysupgrade") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* mac80211: rt2x00: no longer use TXOP_BACKOFF for probe framesDaniel Golle2018-06-112-1/+46
| | | | | | | | Import a revert-commit from Stanislaw Gruszka which significantly improves WiFi performance on rt2x00 based hardware. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry-picked from commit f4a639a3d7d40b4f63c431c2d554c479fbcc6b74)
* ramips: fix network config for ravpower wd03Matthias Badaire2018-06-091-1/+1
| | | | | | | | This device has only one ethernet port. Signed-off-by: Matthias Badaire <mbadaire@gmail.com> [add the existing eth0 as lan block, shorten commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.1 at 2024-07-03 19:22:41 +0000