summaryrefslogtreecommitdiff
path: root/package/kernel/broadcom-diag
Commit message (Collapse)AuthorAgeFilesLines
* broadcom-diag: fix 'autoload' number of diag.koHauke Mehrtens2013-10-021-1/+1
| | | | | | | | Change the autoload number from '5' to '05' so the module loads earlier (as intended). Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> SVN-Revision: 38293
* brcm47xx: update board detection patchesHauke Mehrtens2013-09-181-2/+2
| | | | | | | | | | This is now the version which was send for mainline Linux kernel inclusion. The data needed to detection a board is now stored in init data. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38036
* broadcom-diag: add GPIO configuration for Linksys E2000 V1Hauke Mehrtens2013-09-161-0/+16
| | | | | | | | Thank you Javier Achirica for the patch. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38008
* broadcom-diag: Add WRT310N v1 gpio leds and buttonsHauke Mehrtens2013-09-161-0/+15
| | | | | | Signed-off-by: Flavio Silveira <fggs@terra.com.br> SVN-Revision: 38007
* brcm47xx: add detection code for Huawei E970Hauke Mehrtens2013-09-151-0/+15
| | | | | | | | | This is based on a patch by Mathias Adam. Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38001
* brcm47xx: board detection, GPIO for Linksys E1000 V2.1Hauke Mehrtens2013-09-131-0/+16
| | | | | | | | | | | | | | This patch adds board detection for the Linksys E1000 V2.1 router, as well as GPIO support for same. This fixes bug #14135. Currently, wired networking isn't working on the router, and I haven't tried the wireless, but with this patch, OpenWRT successfully boots, and all the LEDs and buttons work properly. Signed-off-by: Zachary Catlin <zcatlin@indiana.edu> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37977
* brcm47xx: do not use GPIO configuration of WRT54G for every unknown Linksys ↵Hauke Mehrtens2013-09-131-2/+3
| | | | | | | | | | | | | device Most of the Linksys devices without an own GPIO configuration where detected as WRT54G. On one board this made OpenWrt to boot into failsafe every time, because one GPIO configurated as button was not a button. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37970
* broadcom-diag: remove BUFFALO_UNKNOWNHauke Mehrtens2013-08-171-12/+0
| | | | | | | | | | This was itriggered by to many non buffalo devices This closes #14043. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37804
* brcm47xx: change board detection for some Asus devicesHauke Mehrtens2013-08-041-18/+10
| | | | | | | | This closes #13316 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37680
* broadcom-diag: show error message in case something goes wrong with gpio irqHauke Mehrtens2013-08-031-2/+9
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37668
* broadcom-diag: add gpio config for Asus RT-N66UHauke Mehrtens2013-08-031-0/+14
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37667
* broadcom-diag: add gpio config for Linksys E4200v1Hauke Mehrtens2013-08-031-0/+13
| | | | | | | | | GPIO for Linksys E4200v1, tested and works. This closes #13454 and #13894 Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37666
* broadcom-diag: add support for the ASUS RT-N12Hauke Mehrtens2013-08-021-0/+20
| | | | | | | | | | This adds button and led info, which I determined by manually poking the gpio values. Signed-off-by: Josh Stone <cuviper@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37655
* broadcom-diag: increase version numberHauke Mehrtens2013-08-021-1/+1
| | | | | | There are some changes in there and this should be rebuild. SVN-Revision: 37654
* brcm47xx: improve detection of Linksys WRTSL54GSHauke Mehrtens2013-08-011-3/+2
| | | | | | | | This closes #13319 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 37647
* brcm47xx: do not load the kernel modules needed for Ethernet manuallyHauke Mehrtens2013-07-141-0/+5
| | | | | | | add the boot flag to make the kernel modules needed for Ethernet and diag load on startup. SVN-Revision: 37284
* broadcom-diag: make it work with kernel 3.10Hauke Mehrtens2013-07-141-119/+121
| | | | | | In kernel 3.10 the proc interface changed, this patch adds the changes needed for the new interface. SVN-Revision: 37280
* broadcom-diag: check the correct value for not null.Hauke Mehrtens2013-07-141-2/+2
| | | | | | This also fixes a compile warning. SVN-Revision: 37279
* broadcom-diag: reoder some parts.Hauke Mehrtens2013-07-142-156/+126
| | | | | | | This was done to reduce the number of forward declaration needed. This does not contain any real change in the code. SVN-Revision: 37278
* packages: clean up the package folderJohn Crispin2013-06-215-0/+2018
Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37007
generated by cgit v1.1 at 2024-12-14 12:02:30 +0000